EOS-6000 Optical A/B Switch DATASHEET | OCTOBER 2012 Applications Fiber Optical Protection Switching Redundant Ring Architectures FTTx Networks Features Automatic, Manual and Remote Switching Auto-Switching Time Less than 25ms SNMP Control Interface FIBER OPTICS The EOS-6000 Optical A/B Switch is a high-performance solution for network protection and optical redundancy. Packaged in convenient 1RU housing, this line of optical switches provides an automatic or manual fiber switching function to protect the network from inadvertent service outages due to up-stream optical signal degradation. Each fiber’s optical signal power level is continuously monitored, as is an adjustable optical trip threshold for each channel. If the primary fiber’s optical signal power level falls below the desired optical trip threshold, the unit automatically switches to the secondary fiber, thus eliminating the need for intervention of a system operator. The EOS-6000 is capable of manual switching or can be switched remotely via SNMP adding optical protection to many system applications. The EOS-6000 series is designed as a low power, cost-effective, high-performance switching solution for applications that demand reliable and rapid response to changing network conditions Figure 1: Redundant Path Configuration for CATV Broadcast Front Panel LED Indicators Medallion 6000 1 RU Rack-Mount Enclosure with Choice of AC or DC Power Supply RF In MAIN CATV Tx (Main) Medallion 6000 RF In EOS-6000 NMOA8100/8200 Optical Switch EDFA … To WDM & PONs BACKUP CATV Tx (Backup) Optical Characteristics Property Operating Wave Length Units Min. Nm Typ. Max. 1310 +/- 10 or 1550 +/- 20 Insertion Loss dB Return Loss dB Polarization Dependent Loss dB 0.06 0.1 Repeatability dB +/-0.01 +/-0.02 Isolation dB -60 -50 Input Optical Power Switching Time 1.0 55 1.3 60 dBm 24 ms 25 | REV 2012.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice. EOS-6000 Optical A/B Switch FIBER OPTICS DATASHEET | OCTOBER 2012 General and Mechanical Specifications Property Requirement Comments Switching Threshold 20 dB range – see ordering info Switching Mode Auto, Manual, remote Optical Connector SC/APC Other styles available 100 Base-T Ethernet Rear Panel RS-232 interface LED Indicators SNMP v1 Reserved for Factory Use Power, Main, Backup, and Output Indicators Monitoring Interfaces Settable within range Operating Temperature 0C to 50C Storage Temperature -25C to 65C Agency Listings FCC: Subpart B. Part 15, class “A” Unintentional Radiators Power Consumption 5W Supply Range (VDC) (VAC) Maximum 85 to 240 VAC, 50/60 Hz 36 - 72 VDC Dimensions 430x300x44mm Model Number Information (note 1) 6000 – 0S □-□ □ □ □ Operating Wavelenghth Optics Power Supply Switching Threshold range EMCORE Logo 3 – 1310nm 1 – SC/APC 1 – AC 1 – [-30, -10] dBm 0 – No 5 – 1550nm 2 – FC/APC 2 – DC 2 – [-20, 0] dBm 2 – Yes 3 – SC/UPC 3 – [-10, 10] dBm 4 – FC/UPC 4 – [0, 20] dBm 5 – LC/UPC 6- LC/APC Note 1: Not all configurations are available - contact factory. Example: 6000-0S5-1232 1550nm, SC/APC connectors, DC power supply, -10 to + 10 dBm input range, EMCORE Logo. | REV 2012.10 Information contained herein is deemed reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specification at any time without notice.