SRP600A THRU SRP600K FAST SWITCHING PLASTIC RECTIFIER Reverse Voltage - 50 to 800 Volts Forward Current - 6.0 Amperes FEATURES Case Style P600 ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High surge current capability ♦ Construction utilizes void-free molded plastic technique ♦ Fast switching for high efficiency ♦ High temperature soldering guaranteed: 250°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension 1.0 (25.4) MIN. 0.360 (9.1) 0.340 (8.6) 0.360 (9.1) 0.340 (8.6) MECHANICAL DATA 0.052 (1.32) 0.048 (1.22) DIA. Case: Void-free molded package body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.07 ounce, 2.1 grams 1.0 (25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS SRP 600A SRP 600B SRP 600D SRP 600G SRP 600J SRP 600K UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Volts Maximum RMS voltage VRMS 35 70 140 280 420 560 Volts Maximum DC blocking voltage VDC 50 100 200 400 600 800 Volts Maximum average forward rectified current 0.375" (9.5mm) lead length at T A=55°C I(AV) 6.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 300.0 Amps VF 1.3 Volts IR 10.0 1.0 µA mA Maximum instantaneous forward voltage at 6.0A Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C Maximum reverse recovery time (NOTE 1) trr Typical junction capacitance (NOTE 2) CJ Typical thermal resistance (NOTE 3) Operating junction temperature range Storage temperature range 100 100 150 200 200 ns 300.0 pF RΘJA 10.0 °C/W TJ -50 to +125 °C TSTG -50 to +150 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length, with both leads equally to heat sink 4/98 150 RATINGS AND CHARACTERISTIC CURVES SRP600A THRU SRP600K FIG. 1 - FORWARD CURRENT DERATING CURVE FIG. 2 - FORWARD CURRENT DERATING CURVE 20 6.0 5.0 AVERAGE FORWARD CURRENT, AMPERES RESISTIVE OR INDUCTIVE LOAD CAPACITIVE Ipk/IAV = π LOADS 5.0 = Ipk/IAV 10 20 4.0 3.0 2.0 1.0 1.1 x 1.1” (30 x 30mm) COPPER PADS 0 20 40 60 80 100 120 140 160 RESISTIVE OR INDUCTIVE LOAD L=LEAD LENGTH L=0 16 .12” L=0.2 L=0.3 ) 1.6 x 1.6 x 0.04” (40 x 40 x 1mm) COPPER HEAT SINKS mm) 75”( 8 mm 5”(6.3 12 9.5m m) L=0.62”( 15.9mm ) 4 0 75 180 (3.2 80 85 90 95 100 105 110 115 120 125 LEAD TEMPERATURE, °C AMBIENT TEMPERATURE, °C FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 PEAK FORWARD SURGE CURRENT, AMPERES 400 INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 350 TJ=25°C 300 250 TJ=125°C 200 150 100 1 10 100 NUMBER OF CYCLES AT 60 HZ TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 10 1 0.1 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL REVERSE CHARACTERISTICS 10 TJ=100°C 1 TJ=50°C 0.1 0.01 0 TJ=25°C 20 40 60 FIG. 6 - TYPICAL THERMAL RESISTANCE RΘJL, THERMAL RESISTANCE FROM JUNCTION TO LEAD,°C/W INSTANTANEOUS REVERSE CURRENT, MICROAMPERES AVERAGE FORWARD CURRENT, AMPERES 7.0 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 25 L=LEAD LENGTH 20 COPPER HEATSINKS 15 10 5.0 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 EQUAL LEAD LENGTHS TO HEAT SINK, INCHES 1.0