MIC5233 High Input Voltage Low IQ µCap LDO Regulator General Description Features The MIC5233 is a 100mA highly accurate, low dropout regulator with high input voltage and ultra-low ground current. This combination of high voltage and low ground current makes the MIC5233 ideal for multi-cell Li-Ion battery systems. A µCap LDO design, the MIC5233 is stable with either ceramic or tantalum output capacitor. It only requires a 2.2µF capacitor for stability. Features of the MIC5233 include enable input, thermalshutdown, current-limit, reverse-battery protection, and reverse-leakage protection. Available in fixed and adjustable output voltage versions, the MIC5233 is offered in the IttyBitty® SOT-23-5 and SOT223-3 package with a junction temperature range of −40°C to +125°C. Data sheets and support documentation can be found on Micrel’s web site at: www.micrel.com. • • • • • • • • • • • Wide input voltage range: 2.3V to 36V Ultra-low ground current: 18µA Low dropout voltage of 270mV at 100mA High output accuracy of ±2.0% over temperature µCap: stable with ceramic or tantalum capacitors Excellent line and load regulation specifications Zero shutdown current Reverse-battery protection Reverse-leakage protection Thermal-shutdown and current-limit protection IttyBitty® SOT-23-5 and SOT-223-3 packages Applications • • • • • • Keep-alive supply in notebook and portable computers USB power supply Logic supply for high-voltage batteries Automotive electronics Battery-powered systems 3 − 4 cell Li-Ion battery input range _________________________________________________________________________________________________________________________ Typical Application Ultra-Low Current Adjustable Regulator Application Ground Current vs. Input Voltage IttyBitty is a registered trademark of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 2012 M9999-071212-B Micrel, Inc. MIC5233 Ordering Information Marking Voltage Junction Temperature Range(1) Package MIC5233-1.8YM5 L318 1.8V −40°C to +125°C SOT-23-5 MIC5233-2.5YM5 L325 2.5V −40°C to +125°C SOT-23-5 MIC5233-3.0YM5 L330 3.0V −40°C to +125°C SOT-23-5 MIC5233-3.3YM5 L333 3.3V −40°C to +125°C SOT-23-5 Part Number MIC5233-5.0YM5 L350 5.0V −40°C to +125°C SOT-23-5 MIC5233YM5 L3AA Adjustable −40°C to +125°C SOT-23-5 MIC5233-3.3YS 33YS 3.3V −40°C to +125°C SOT-223 Note: 1. Other voltages available. Contact Micrel for details. Pin Configuration 5-Pin SOT-23 (M5) 3-Pin SOT-223 (S) Pin Description Pin Number SOT-223 Pin Number SOT-23 Pin Name Pin Function 1 1 IN Supply Input. 2 2 GND 3 4 3 TAB July 2012 5 Ground. EN Enable (Input). Logic LOW = shutdown; logic HIGH = enable. NC No Connect. ADJ Adjustable (Input). Feedback input; connect to resistive voltage-divider network. OUT Regulator Output. GND Ground. 2 M9999-071212-B Micrel, Inc. MIC5233 Absolute Maximum Ratings(1) Operating Ratings(2) Input Supply Voltage (VIN).............................. −20V to +38V Enable Input Voltage (VEN)............................ −0.3V to +38V Power Dissipation (PDIS)............................Internally Limited Junction Temperature (TJ) ........................−40°C to +125°C Storage Temperature (TS).........................−65°C to +150°C ESD Rating(3) ................................................. ESD Sensitive Input Supply Voltage (VIN)............................. +2.3V to +36V Enable Input Voltage (VEN)................................. 0V to +36V Junction Temperature (TJ) ........................ −40°C to +125°C Package Thermal Resistance SOT-23-5 (θJA) .................................................235°C/W SOT-223 (θJA) ....................................................50°C/W Electrical Characteristics(4) TJ = 25°C with VIN = VOUT + 1V; IOUT = 100µA; Bold values indicate –40°C < TJ < +125°C; unless otherwise specified. Parameter Condition Min. Output Voltage Accuracy Variation from nominal VOUT Typ. Max. −1.0 +1.0 −2.0 +2.0 Units % Line Regulation VIN = VOUT + 1V to 36V 0.04 0.5 % Load Regulation IOUT = 100µA to 100mA 0.25 1 % IOUT = 100µA Dropout Voltage 50 230 IOUT = 50mA 400 270 IOUT = 100mA mV 400 450 18 IOUT = 100µA Ground Current 300 30 35 IOUT = 50mA 0.25 0.70 IOUT = 100mA 1 2 µA mA Ground Current in Shutdown VEN ≤ 0.6V; VIN + 36V (SOT-23 package only) 0.1 1 µA Short-Circuit Current VOUT = 0V 190 350 mA Output Leakage, Reverse Polarity Input Load = 500Ω; VIN = −15V −0.1 µA Enable Input (SOT-23 Package Only) Input LOW Voltage Regulator OFF Input HIGH Voltage Regulator ON 2.0 VEN = 0.6V; Regulator OFF −1.0 Enable Input Current Start-Up Time 0.6 V V 0.01 1.0 VEN = 2.0V; Regulator ON 0.1 1.0 VEN = 36V; Regulator ON 0.5 2.5 Guaranteed by design 1.7 7 µA ms Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF. 4. Specification for packaged product only July 2012 3 M9999-071212-B Micrel, Inc. MIC5233 Typical Characteristics July 2012 4 M9999-071212-B Micrel, Inc. MIC5233 Typical Characteristics (Continued) July 2012 5 M9999-071212-B Micrel, Inc. MIC5233 Functional Characteristics July 2012 6 M9999-071212-B Micrel, Inc. MIC5233 Functional Diagrams Fixed Output Voltage (M5 Package) Fixed Output Voltage (S Package) July 2012 7 M9999-071212-B Micrel, Inc. MIC5233 Functional Diagrams (Continued) Adjustable Output Voltage July 2012 8 M9999-071212-B Micrel, Inc. MIC5233 To determine the maximum power dissipation of the package, use the junction-to-ambient thermal resistance of the device and the following Equation 1: Application Information Enable/Shutdown The MIC5233 comes with an active-high enable pin that allows the regulator to be disabled. Forcing the enable pin low disables the regulator and sends it into a “zero” off-mode-current state. In this state, current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output voltage. ⎛ TJ(MAX) − TA PD(MAX) = ⎜⎜ θ JA ⎝ Eq. 1 TJ(MAX) is the maximum junction temperature of the die, 125°C, and TA is the ambient operating temperature. θJA is layout dependent; Table 1 shows examples of the junction-to-ambient thermal resistance for the MIC5233: Input Capacitor The MIC5233 has high input voltage capability up to 36V. The input capacitor must be rated to sustain voltages that may be used on the input. An input capacitor may be required when the device is not near the source power supply or when supplied by a battery. Small, surface mount, ceramic capacitors can be used for bypassing. A larger value may be required if the source supply has high ripple. Output Capacitor The MIC5233 requires an output capacitor for stability. The design requires 2.2µF or greater on the output to maintain stability. The design is optimized for use with low-ESR ceramic chip capacitors. High-ESR capacitors may cause high-frequency oscillation. The maximum recommended ESR is 3Ω. The output capacitor can be increased without limit. Larger valued capacitors help to improve transient response. X7R/X5R dielectric-type ceramic capacitors are recommended because of their temperature performance. X7R-type capacitors change capacitance by 15% over their operating temperature range and are the most stable type of ceramic capacitors. Z5U and Y5V dielectric capacitors change value by as much as 50% and 60% respectively over their operating temperature ranges. To use a ceramic chip capacitor with Y5V dielectric, the value must be much higher than an X7R ceramic capacitor to ensure the same minimum capacitance over the equivalent operating temperature range. Package θJA Recommended Minimum Footprint SOT-23-5 235°C/W SOT223 50°C/W Table 1. SOT23-5 and SOT-223 Thermal Resistance The actual power dissipation of the regulator circuit can be determined using Equation 2: PD = (VIN − VOUT)IOUT + VIN × IGND Eq. 2 Substituting PD(MAX) for PD and solving for the operating conditions that are critical to the application will give the maximum operating conditions for the regulator circuit. For example, when operating the MIC5233-3.0YM5 at 50°C with a minimum footprint layout, the maximum input voltage for a set output current can be determined as follows: ⎛ 125°C − 50°C ⎞ PD(MAX) = ⎜ ⎟ ⎝ 235°C/W ⎠ Eq. 3 where PD(MAX) = 319mW. No-Load Stability The MIC5233 will remain stable and in regulation with no load unlike many other voltage regulators. This is especially important in CMOS RAM keep-alive applications. The junction-to-ambient (θJA) thermal resistance for the minimum footprint is 235°C/W, from Table 1. It is important that the maximum power dissipation not be exceeded to ensure proper operation. Since the MIC5233 was designed to operate with high input voltages, careful consideration must be given so as not to overheat the device. With very high input-to-output voltage differentials, the output current is limited by the total power dissipation. Thermal Consideration The MIC5233 is designed to provide 100mA of continuous current in a very-small package. Maximum power dissipation can be calculated based on the output current and the voltage drop across the part. July 2012 ⎞ ⎟ ⎟ ⎠ 9 M9999-071212-B Micrel, Inc. MIC5233 Maximum input voltage for a 10mA load current at 50°C ambient temperature is 34.9V, utilizing virtually the entire operating voltage range of the device. Total power dissipation is calculated using the following equation: PD = (VIN − VOUT)IOUT + VIN × IGND Eq. 4 Adjustable Regulator Application The MIC5233BM5 can be adjusted from 1.24V to 20V by using two external resistors (Figure 1). The resistors set the output voltage based on the following equation: Due to the potential for input voltages up to 36V, ground current must be taken into consideration. If we know the maximum load current, we can solve for the maximum input voltage using the maximum power dissipation calculated for a 50°C ambient, 319mV. ⎛ ⎛ R1 ⎞ ⎞ VOUT = VREF ⎜⎜1+ ⎜ ⎟ ⎟⎟ ⎝ ⎝ R2 ⎠ ⎠ PD(MAX) = (VIN − VOUT)IOUT + VIN × IGND where VREF = 1.24V. 319mW = (VIN − 3V)100mA + VIN × 2.8mA Eq. 5 Feedback resistor R2 should be no larger than 300kΩ. Ground pin current is estimated using the typical characteristics of the device. 619mW = VIN (102.8mA) VIN = 6.02V Eq. 8 Eq. 6 For higher current outputs only a lower input voltage will work for higher ambient temperatures. Assuming a lower output current of 10mA, the maximum input voltage can be recalculated: Figure 1. Adjustable Voltage Application 319mW = (VIN − 3V)10mA + VIN × 0.1mA 349mW = VIN × 10.1mA VIN = 34.9V July 2012 Eq. 7 10 M9999-071212-B Micrel, Inc. MIC5233 Package Information 5-Pin SOT-23 (M5) July 2012 11 M9999-071212-B Micrel, Inc. MIC5233 Package Information (Continued) 3-Pin SOT-223 (S) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry, specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2003 Micrel, Incorporated. July 2012 12 M9999-071212-B