Ordering number : ENA1772A LB11685AV Monolithic Digital IC 3-phase sensor less Motor driver http://onsemi.com Overview The LB11685AV is a three-phase full-wave current-linear-drive motor driver IC. It adopts a sensor less control system without the use of a Hall Effect device. For quieter operation, the LB11685AV features a current soft switching circuit and be optimal for driving the cooling fan motors used in refrigerators, etc. Functions • Three-phase full-wave linear drive (Hall sensor-less method) • Built-in three-phase output voltage control circuit • Motor lock protection detection output • Built-in thermal shut down circuit • Built-in current limiter circuit • Built-in motor lock protection circuit • FG output made by back EMF • Beat lock prevention circuit Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Maximum supply voltage VCC max Input applied voltage VIN max Maximum output current IO max *1 Allowable power dissipation Pd max Operating temperature Storage temperature Conditions Ratings Unit 19 V -0.3 to VCC +0.3 V 1.2 A 1.05 W Topr -40 to 85 °C Tstg -55 to 150 °C 150 °C Junction temperature Tj max *1: The IO is a peak value of motor-current. Mounted on a board *2 *2: Specified board: 76.1mm × 114.3mm × 1.6mm, glass epoxy board. Caution 1) Absolute maximum ratings represent the value which cannot be exceeded for any length of time. Caution 2) Even when the device is used within the range of absolute maximum ratings, as a result of continuous usage under high temperature, high current, high voltage, or drastic temperature change, the reliability of the IC may be degraded. Please contact us for the further details. Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Semiconductor Components Industries, LLC, 2013 May, 2013 71812 SY/61610 SY 20100604-S00001 No.A1772-1/7 LB11685AV Recommended Operating Conditions at Ta = 25°C Parameter Symbol Recommended Supply voltage VCC Operating supply voltage VCC op Conditions Ratings Unit 12.0 V 4.5 to 18.0 V Electrical Characteristics at Ta = 25°C, VCC = 5.0V Parameter Symbol Ratings Conditions min Supply current ICC FC1 = FC2 = 0V Internal regulate voltage VREG Output voltage (source) VOSOUR IO = 0.8A *3 Output voltage (sink) VOSINK IO = 0.8A *3 Current limiter VOLIM MCOM pin VINCOM typ 5 3.0 Unit max 10 20 mA 3.3 3.6 V 1.3 1.7 V 0.5 1.3 V 0.300 0.332 V 0 VCC - 2 V 0.268 common-input voltage range ICOM+ MCOM = 7V 30 80 μA ICOM- MCOM = 7V 30 80 μA RTCOM RTCOM = ICOM+ / ICOM- 0.6 1.4 VCO input bias current IVCO VCO = 2.3V VCO oscillation minimum fVCOmin VCO = 2.1V, CX = 0.015μF Design target *2 930 Hz fVCOmax VCO = 2.7V, CX = 0.015μF Design target *2 8.6 kHz CX charge / discharge current ICX VCO = 2.5V, CX = 1.6V CX hysteresis voltage ΔVCX C1 (C2) charge current IC1(2)+ VCO = 2.5V, C1(2) = 1.3V C1 (C2) discharge current IC1(2)- VCO = 2.5V, C1(2) = 1.3V 12 C1 (C2) charge / discharge RTC1(2) RTC1(2) = IC1(2)+ / IC1(2)- 0.8 MCOM pin Source current for hysteresis MCOM pin Sink current for hysteresis MCOM pin hysteresis current ratio frequency VCO oscillation maximum frequency 0.2 μA μA 70 100 140 0.35 0.55 0.75 12 20 28 μA 20 28 μA 1.0 1.2 current ratio C1/C2 charge current ratio RTCCHG RTCCHG = IC1+ / IC2+ 0.8 1.0 1.2 C1/C2 discharge current ratio RTCDIS RTCDIS = IC1- / IC2- 0.8 1.0 1.2 C1 (C2) cramp voltage width VCW1(2) 1.0 1.3 1.6 V V FG output low level voltage VFGL IFG = 3mA 0.5 RD output low level voltage VRDL IRD = 3mA 0.5 Thermal shut down operating TTSD Junction temperature ΔTTSD Junction temperature temperature *1 Thermal shut down hysteresis 150 v 180 °C 15 °C Design target *2 temperature *1 Design target *2 *1: The thermal shut down circuit is built-in for protection from damage of IC. But its operation is out of Topr. Design thermal calculation at normal operation. *2: Design target value and no measurement is made. *3: The IO is a peak value of motor-current. No.A1772-2/7 LB11685AV Package Dimensions unit : mm (typ) 3315 Pd max - Ta 0.5 5.6 13 7.6 24 1 12 0.8 0.15 0.3 1.5MAX (1.3) (0.48) Allowable power dissipation, Pd max -- W 1.5 9.75 Specified circuit board : 114.3 ×76.1× 1.6mm3 glass epoxy board 1.05 1.0 0.55 0.5 -20 0 20 40 60 80 100 Ambient temperature, Ta -- C 0.1 0 -40 SANYO : SSOP24J(275mil) Pin Assignment UOUT 1 24 VOUT (NC) 2 23 WOUT (NC) 3 22 (NC) PGND 4 21 (NC) MCOM 5 20 RF (NC) 6 19 VCC SGND 7 18 REG FG 8 17 VOH RD 9 16 FC1 (NC) 10 15 FC2 VCO 11 14 C2 CX 12 13 C1 No.A1772-3/7 LB11685AV Block Diagram 1 24 2 23 3 22 Pre Drive Distributor 4 21 Output Switching Control 5 Start Up & Mask Timing 6 Reference Voltage 20 Bandgap 19 + 7 Power On Reset 18 TSD 8 Motor Lock Detector 9 FG 17 Torque Ripple Rejection & Current Limit 10 15 PLL Low Voltage Control 14 11 VCO 12 16 Soft Switching 13 No.A1772-4/7 LB11685AV Pin Function Pin No. Pin name 1 UOUT 23 WOUT 24 VOUT 4 PGND Function Equivalent circuit Each output pin of three phases. Pin No.20 GND pin in the output part. This pin is connected to GND. The SGND pin is also Pin No.1,23,24 connected to GND 20 RF Pin to detect output current. By connecting a resistor between this pin and VCC, the Pin No.4 output current is detected as a voltage. The current limiter is operated by this voltage. 5 MCOM Motor coil midpoint input pin. The coil voltage waveform is detected based on this voltage. SGND SGND SGND VCC VCC Pin No.5 SGND 7 SGND SGND Ground pin (except the output part) This pin is connected to GND. The PGND pin is also connected to GND. 8 FG FG out made by back EMF pin. It synchronizes FG out with inverted V-phase. Pin No.8 No.9 When don’t use this function, open this pin. 9 RD Motor lock protection detection output pin. SGND Output with L during rotation of motor. SGND Open during lock protection of motor (High-impedance). When don’t use this function, open this pin. 11 VCO PLL output pin and VCO input pin. To stabilize PLL output, connect a capacitor between this VREG pin and GND. VCC Pin No.11 VREG SGND VREG SGND 12 CX VCO oscillation output pin. Operation frequency range and minimum frequency are VREG determined by the capacity of the capacitor connected to this pin. VCC Pin No.12 SGND SGND Continue to the next page. No.A1772-5/7 LB11685AV Continue from the former page. Pin No. Pin name Function 13 C1 Soft switching adjustment pin. 14 C2 The triangular wave from is form formed by connecting a Equivalent circuit capacitor with this pin. VCC And, the switching of three-phase output is adjusted by the slope. Pin No.13 14 SGND SGND 15 FC2 Frequency characteristic correction pin 2. VREG To suppress the oscillation of control system closed loop of sink-side, connect a capacitor between this pin and VCC GND. Pin No.15 SGND SGND 16 FC1 Frequency characteristic correction pin 1. VCC To suppress the oscillation of control system closed loop of source-side, connect a capacitor between this pin and Pin No.16 GND. SGND SGND 17 VOH Three-phase output high level output pin. VCC To stabilize the output voltage of this pin, connect a capacitor between this pin and the VCC pin. VCC Pin No.17 SGND SGND 18 VREG DC voltage (3.3V) output pin. VCC Connect a capacitor between this pin and GND for VCC stabilization. Pin No.18 SGND SGND 19 VCC Pin to supply power-supply voltage. To curb the influence of ripple and noise. The voltage should be stabilized. No.A1772-6/7 LB11685AV Application Circuit Example * Each fixed number in the following FIG, is the referential value. FAN MOTOR 1 24 2 23 3 22 4 21 5 20 6 19 7 18 8 17 9 16 10 15 11 14 12 13 VCC ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A1772-7/7