EVALSPEAr320PLC Evaluation board for SPEAr320 embedded MPU Data brief Features ■ CPU board – SPEAr320 embedded MPU – Up to 2 Gbits DDR2 333 MHz (std 128 Mbytes) – Up to 16 Mbytes serial Flash memory (std 8 Mbytes) – Two USB 2.0 full host port channels – One USB 2.0 host device port – One serial port (up to 115 baud) – JTAG debug ports ■ Application board – 2 x Ethernet RJ-45 connectors (ST802RT1A) – 2 x CAN DB9 plug connectors – 3 x RS-232 DB9 plug connectors (ST3232EBTR) – 1 x RS-485 DB9 socket connector (ST3485EBDR) – Digital input connectors (parallel and serial) compatible with STEVAL-IFP007V1, STEVAL-IFP008V1 and STEVALIFP004V1 evaluation boards Figure 1. – Digital output connectors (parallel and serial) compatible with STEVAL-IFP009V1, STEVAL-IFP001V1, STEVAL-IFP002V1 and STEVAL-IFP006V1 evaluation boards – On-board temperature sensor (STLM20W87F) and potentiometer (analog input for ADC) – Analog extension connector featuring 8 ADC lines – General-purpose extension connector with GPIOs and I2C functionality – DC/DC converter L7986A (+24 V / +5 V) – MicroSD card socket – 4 LEDs, 2 general-purpose buttons and system reset button Description This evaluation board can be used to evaluate the SPEAr320 microprocessor with a variety of devices and especially its media independent interface (MII) automation mode. The EVALSPEAr320PLC evaluation board kit consists of two boards: a CPU board and a MII mode application board. The SPEAr320 microprocessor is mounted on the CPU board that is plugged on the MII mode application board. EVALSPEAr320PLC evaluation board September 2010 Doc ID 18019 Rev 1 For further information contact your local STMicroelectronics sales office. 1/3 www.st.com 3 Revision history EVALSPEAr320PLC Revision history Table 1. 2/3 Document revision history Date Revision 20-Sep-2010 1 Changes Initial release. Doc ID 18019 Rev 1 EVALSPEAr320PLC Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 18019 Rev 1 3/3