STEVAL-ISA011V1 VIPER12ADIP-E low power AC/DC adapter demonstration board (suitable for the STEVAL-ILL002V1) Data brief Features ■ Minimum AC input voltage = 88 Vrms ■ Maximum AC input voltage = 265 Vrms ■ Max output power = 4.1 W ■ Output voltage = 4.5 V ■ Max output current = 900 mA ■ Efficiency (at full load and 230 Vac) = 70 % ■ Efficiency (at full load and 115 Vac) = 70 % Description The STEVAL-ISA011V1 demonstration board is a low power (4.1 W output), general purpose adapter. The design is based on the VIPER12ADIP-E monolithic device which, in the same package, integrates the high voltage power switch and the basic control function needed for a current mode flyback converter. STEVAL-ISA011V1 The board can handle a wide range AC input voltage, from 88 Vac to 265 Vac, with one output voltage of 4.5 V delivering a maximum output current of 900 mA. The main applications for this board are auxiliary power supplies and wall-plug adapters. September 2010 Doc ID 18014 Rev 1 For further information contact your local STMicroelectronics sales office. 1/4 www.st.com 4 Doc ID 18014 Rev 1 17& & &E )9 &Q)< 8 9LSHU$ ' 677+5 Q) & 5 ( & ) N5 '1 8 3& 5 '67368 8 7/ &Q) 5N 3UHFLVLRQ 5HVLVWRU 5N 3UHFLVLRQ 5HVLVWRU P)90%=5XE\FRQ & 5 N 9$ - 5 N STEVAL-ISA011V evaluation board schematic &21 )9 &D 5N 5 N: Figure 1. )&;FDS )P$ & S)9 7 Schematic circuit - ' ± ' 6 ' 6 ' )% 9'' ' 2/4 /P+ 1 $9%ULGJH Schematic circuit STEVAL-ISA011V1 $, STEVAL-ISA011V1 2 Revision history Revision history Table 1. Document revision history Date Revision 23-Sep-2010 1 Changes Initial release. Doc ID 18014 Rev 1 3/4 STEVAL-ISA011V1 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 4/4 Doc ID 18014 Rev 1