VX-501 Voltage Controlled Crystal Oscillator VX-501 Features Applications • AT-Cut Crystal • Surface Mount FR4 based package • Reflow Process Compatible • Low Phase Noise • Tight Stabilities • Frequency Range 1 - 1200MHz • Standard Frequencies 2.048; 10; 16,384; 30,72; 32,768; 38,88; 44.8; • 52; 61.44; 68.736; 76.8; 77.76; 81.92; 92.16; • 100; 112; 122.88; 125; 134.4; 153.6; 155.52; • 160; 179.2; 184.32; 245.76; 312.5; 320; • 368.64; 400; 448; 471.8592; 491.52; 622.08; • 672; 737.28; 800MHz • Previous Model Number: C5310 • Base Stations • Test Equipment • Synthesizers • Switching Performance Specifications Frequency Stabilities1 Parameter Min vs. operating temperature range (referenced to +25°C) Typical Max Units Condition -15 +15 ppm -20 to +70°C Initial tolerance vs. supply voltage change vs. load change vs. aging / 1 Year vs. aging (following years) -10 -3 -1 -3 -1 +10 +3 +1 +3 +1 ppm ppm ppm ppm ppm @Vc=Vs/2 VS ±5% Load ±10% vs. operating temperature range (referenced to +25°C) -30 +30 ppm -40 to +85°C Initial tolerance vs. supply voltage change vs. load change vs. aging / 1 Year vs. aging (following years) -15 -3 -2 -3 -1 +15 +3 +2 +3 +1 ppm ppm ppm ppm ppm @Vc=Vs/2 VS ±5% Load ±10% Page 1 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Performance Specifications Supply Voltage (Vs) Min Typical Max Units 3.135 3.3 3.465 VDC Current consumption 40 mA @ HCMOS, Sinewave Current consumption 90 mA @ PECL, LVDS 5.25 VDC Current consumption 30 mA @ HCMOS, Sinewave Current consumption 80 mA @ PECL, LVDS Supply voltage (standard) Supply voltage 4.75 5 Condition Options Parameter RF Output Signal HCMOS Load 15 pF Rise and Fall time Duty cycle 40 Signal 5 ns @ 15 pF 10 to 90% 60 % @ Vs / 2 PECL 50 Ω Rise and Fall time Duty cycle 45 Signal 1 ns 55 % 20 to 80% Options Load LVDS Load 100 Ω Rise and Fall time Duty cycle 40 Signal 1 ns 60 % 10 to 90% Sinewave Load 50 Output Power -3 0 Tuning Range ±75.0 ±90 Ω 3 dBm Frequency Tuning (EFC) Linearity ±200.0 ppm 10 % Tuning Slope Positive Control Voltage Range 0 0.5 Frequency Control Input Impedance 10 1.65 2.5 3.3 4.5 VDC VDC with Vs = 3.3V with Vs = 5V kΩ Additional Parameters Phase Noise Jitter Phase Noise Jitter Phase Noise Jitter Phase Noise Jitter -78 -110 -138 -155 -161 0.2 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ 12kHz .. 20MHz @100MHz LVCMOS 3.3V -75 -105 -130 -145 -153 0.1 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ 12kHz .. 20MHz @ 153.6 MHz PECL 3.3V -59 -90 -118 -137 -144 0.1 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ 12kHz .. 20MHz @ 300 MHz LVDS 3.3V -60 -95 -121 -141 -150 0.03 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz ps RMS 10 Hz 100 Hz 1 kHz 10 kHz 100 kHz @ 12kHz .. 20MHz @ 491.52 MHz PECL 3.3V Page 2 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Performance Specifications Additional Parameters Subharmonics -40 Weight dBc For f > 160 MHz 2.0 g Processing & Packing Handling & Processing Note Absolute Maximum Ratings Supply voltage (Vs) 6.0 V Operable Temperature Range -40 +85 °C Storage Temperature Range -55 +125 °C Cross Reference Typical CrossPhase Reference NoiseList List and Jitter Phase Noise Phase Noise VX-501 @ 100 MHz LVCMOS VX-501 @ 153.6 MHz LVPECL Phase Noise Phase Noise VX-501 @ 300 MHz LVDS VX-501 @ 491.52 MHz LVPECL Page 3 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Enclosure Package Codes Package Codes Type Height “H” Type Height “H” G223B 5.9 G218B 5.9 G218E 4.7 G218C 2.8 Pin Connections Pin Connections 1 Control Voltage (Vc) 1 Control Voltage (Vc) 2 Ground 2 N.C. / Enable (Option) 3 RF Output 3 Ground 4 Supply Voltage Input (Vs) 4 RF Output 5 RF Output complementary (PECL / LVDS) N.C. (CMOS) 6 Supply Voltage Input (Vs) Marking Enable true table (optional) VX-501-xxxx HCMOS LVPECL / LVDS Frequency Pin 2 Pin 4 Pin 5 Pin 4 Pin 5 AYYWW High Data N.C. No Data No Data Open Data N.C. Data Compl. Data Low High Tristate N.C. Data Compl. Data Page 4 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Standard Shipping Method Lage im Gurt Position in tape Pin 1 A Abwickelrichtung Unwinding direction X B P Gurtunterseite Tape buttom side K Gurtoberseite Tape upper side *bei W ≤ 24 mm nur untere Lochreihe ∗by W ≤ 24 mm only lower hole line Enclosure Type Tape Width W (mm) Quantity per meter Quantity per reel Dimension P G218B/G223B 24 83.3 850 12 Recommended Reflow Profile Profile Feature Pb-Free Assembly/ Sn-Pb Assembly Profile Feature Pb-Free Assembly/ Sn-Pb Assembly Average ramp-up rate (TL to TP) 3°C/second max. Time 25°C to Peak Temperature 8 minutes max. 150°C 200°C 60-180 seconds Time maintained above -Temperature (TL) -Time (tL) 217°C 60-150 seconds Preheat -Temperature Min TSmin -Temperature Min TSmax -Time (min to max) tS TSmax to TL -Ramp-up Rate 3°C/second max Time maintained above -Temperature (TL) -Time (tL) 217°C 60-150 seconds Time within 5°C of actual Peak Temperature (tP) 20-40 seconds Peak Temperature (TP) max 260°C Ramp-down Rate 6°C/ second max Note: All temperatures refer to topside of the package, measured on the package body surface. Page 5 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Ordering Information VX-501 0 - E A J - 105 0 - 52M0 Frequency Model Code Enable 0: No Enable 1: Enable Height 0: 5.9 mm (G218B / G223B) 1: 4.7 mm (G218E) 2: 2.8 mm (G218C) Stability Code E-305: ±30ppm J-105: ±15ppm Supply Voltage D: 5V E: 3.3V RF Output Code A: HCMOS C: PECL D: LVDS E: Sinewave Temperature Range E: -40°C to +85°C J: -20°C to +70°C Notes: 1. Contact factory for improved stabilities or additional product options. Not all options and codes are available at all frequencies. 2. Unless other stated all values are valid after warm-up time and refer to typical conditions for supply voltage, frequency control voltage, load, temperature (25°C). 3. Phase noise degrades with increasing output frequency. 4. Subject to technical modification. 5. Contact factory for availability. For Additional Information, Please Contact USA: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Europe: Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 7268-801-0 Fax: +49 (0) 7268-801-281 Asia: Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Rev: 05/2012 Page 6 of 5 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com