Document 185-1 Maxi Spring™ Air Core Inductors • Air core inductors feature higher Q, L and current ratings • Rigid package provides a flat surface for pick and place • Leads are locked in position for precise terminal spacing Weight 0.42 – 0.59 g Terminations RoHS compliant tin-silver (96.5/3.5) over copper. Other terminations available at additional cost. Ambient temperature –40°C to +125°C with Irms current, +125°C to +140°C with derated current Storage temperature Component: –40°C to +140°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +5 to +70 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 800/13″ reel Plastic tape: 24 mm wide, 0.3 mm thick, 12 mm pocket spacing, 6.1 mm pocket depth PCB washing Only pure water or alcohol recommended Inductance2 Percent Part number1Turns (nH) tolerance3 132-09SM_L_9 90 5,2 132-10SM_L_10 111 5,2 132-11SM_L_11 130 5,2 132-12SM_L_12 169 5,2 132-13SM_L_13 206 5,2 Q2 Q2 Test freq. SRF min4 DCR max5 Irms6 typ min (MHz) (GHz) (mOhm)(A) 11495 50 1.140 15 3.5 10487 50 1.020 15 3.5 10487 50 0.900 20 3.0 11495 50 0.875 25 3.0 11495 50 0.800 30 3.0 132-14SM_L_14 132-15SM_L_15 132-16SM_L_16 132-17SM_L_17 132-18SM_L_18 222 246 307 380 422 5,2 5,2 5,2 5,2 5,2 11092 11495 11495 11495 11495 50 50 50 50 50 0.730 0.685 0.660 0.590 0.540 35 35 35 50 60 132-19SM_L_19 132-20SM_L_20 491 538 5,2 5,2 11495 10487 50 50 0.535 0.490 65 2.0 90 2.0 1. When ordering, specify tolerance, termination and packaging codes: 132-20SMGLD Termination: L = RoHS compliant tin-silver (96.5/3.5) over copper. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Tolerance: G=2% J = 5% Packaging:D = 13″ machine-ready reel. EIA-481 embossed plastic tape (800 parts per full reel). B = Less than full reel. In tape, but not machine-ready. To have a leader and trailer added ($25 charge), use code letter D instead. 3.0 3.0 3.0 2.5 2.5 2. Inductance and Q tested at 50 MHz on an Agilent/HP 4291A with a 16193 fixture and correlation. 3. Tolerances in bold are stocked for immediate shipment. 4. SRF tested on the Agilent/HP 8753D and a Coilcraft CCF1248 test fixture. 5. DCR tested on the Cambridge Technology Model 510 Micro Ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Document 185-1 Revised 01/11/11 Document 185-2 Designer’s Kit C319 contains 8 each of all 5% values. Designer’s Kit C319-2 contains 8 each of all 2% values. Maxi Spring™ Air Core Inductors Typical L vs Frequency Typical Q vs Frequency 1000 250 900 200 90 nH 422 nH 700 600 500 Q factor Inductance (nH) 800 246 nH 400 169 nH 150 169 nH 246 nH 422 nH 100 300 90 nH 200 50 100 0 10 1 0 1000 100 1 10 100 1000 Frequency (MHz) Frequency (MHz) Typical Irms Derating 120 110 90 80 70 60 50 40 30 25°C Percent of rated Irms 100 20 10 0 -40 -20 0 20 40 60 80 100 120 140 Ambient temperature (°C) A E D Recommended Land Pattern C Strip Length B A max B max C max D E 0.415 10,55 0.260 6,60 0.235 5,97 0.240 ±0.015 6,10 ±0,38 0.314 ±0.020 7,98 ±0,51 0.095 2,42 0.080 2,04 0.185 4,70 135° max 0.314 7,98 0° min Dimensions are in inches mm Document 185-2 Revised 01/11/11