5021D-A13 3 GHz, 35 µs Max External Fiber Delay Line System DATASHEET | NOVEMBER 2013 MICROWAVE The 5021D-A13, 3 GHz fiber optic delay line delivers unmatched performance for radar testing, signal processing, phased array antennas and phase noise testing. This rugged device eliminates many of the problems that are inherent in alternative transceiver technologies. Applications Radar Testing Signal Processing EMCORE’s fiber optic delay lines provide bandwidth that is essentially independent of fiber length, loss or delay, and triple transit signals that are immeasurable. In addition to enhanced electrical performance, the delay lines provide several mechanical advantages. EMCORE’s technology takes advantage of the rigid yet flexible properties of fiber optic cable to provide repeatable enhanced phase and group delay characteristics. The small size of these components allows for a long delay in a compact package with the superior temperature stability of fiber. Block Diagram Delay Line Phased Array Antennas DC Driver Phase Noise Processing RF IN Laser PL Features PR Photodiode RF OUT Fiber Delay Spool Bandwidth to 3 GHz High-Dynamic-Range -40 to +65°C Typical S21 Graph Delays to 35 Microseconds Flat Frequency Response Low Phase Noise © 2013 EMCORE Corporation | REV 2013.11 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5021D-A13 3 GHz, 35 µs Max External Fiber Delay Line System DATASHEET | NOVEMBER 2013 MICROWAVE Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Min Max Unit Operating Temperature Range of Baseplate -40 +65 °C Storage Temperature -55 +85 °C - 20 dBm RF Input Power Electrical Characteristics Parameter 5021D-A13 Unit Upper Band Edge Frequency 3 GHz Lower Band Edge Frequency 0.05 GHz Amplitude Flatness 4 dB p-p Delay Time 35 µ-sec, max Insertion Loss @ 1 GHz1 35 µ-sec -41 dB, max Input RF Return Loss, max 0.05 GHz - 3 GHz -7.0 dB Output RF Return Loss, max 0.05 GHz - 3 GHz -9.0 dB Impedance 50 Ohm Input 1 dB Compression, min +20 dBm Input Third Order Intercept, min 0.05 GHz - 3 GHz +30 dBm Noise Figure 0.05 GHz - 3 GHz 44 dB 1. Shorter delay times will have lower loss. DC Interface Characteristics Pin Number Min Typ Max Max Ripple Current 1 14 V 15 V 16 V 100 mV p-p 0.3 A max 2 4.5 V 5V 5.5 V 200 mV p-p 1.6 A max Pin/Package Information Nine-Pin, Male D-Sub Connector Pin Number Function 1 +15 VDC 2 +5 VDC 3 Not Used 4 Ground 5 Ground 6 Photodiode Current Monitor 7 Alarm Common 8 Laser Current Monitor 9 Alarm © 2013 EMCORE Corporation | REV 2013.11 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5021D-A13 3 GHz, 35 µs Max External Fiber Delay Line System DATASHEET | NOVEMBER 2013 MICROWAVE Outline Drawing DC Monitor Voltages Photodiode Current, Pin 6: 1 V/1 mA (into 1 MOhm load). Proportional to Photodiode Optical Input Power. Laser DC Current, Pin 8: 1 V/100 mA (into 1 MOhm load) Alarm Circuits Summary Alarm, Pins 7 & 9: Closed when unit is OK. Open if fault or no DC power. The alarm is a dry, form A contact. The alarm is a summary of : 1. +5 VDC Regulator 2. Laser Temperature 3. Laser Optical Output Power 4. Photodiode Optical Power Input Front Panel LEDs Power On Laser Temperature Stable Laser Optical Power Stable Photodiode Optical Input Power © 2013 EMCORE Corporation | REV 2013.11 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5021D-A13 3 GHz, 35 µs Max External Fiber Delay Line System DATASHEET | NOVEMBER 2013 MICROWAVE Order Information Model Number Description 5021D-A13-XXXXXX Delay Line, 3 GHz, SMA, Delay Time to 35 μs Note1: XXXXXX designates required delay time. Example: 5021D-A13-032550 is a 3 GHz system with 35 μs delay Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1M laser product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class 1M laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. An additional warning for Class 1M laser products. For diverging beams, this warning shall state that viewing the laser output with certain optical instruments (for example: eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. For collimated beams, this warning shall state that viewing the laser output with certain instruments designed for use at a distance (for example: telescopes and binoculars) may pose an eye hazard. Wavelength = 1.3/1.5 μm. Maximum power = 30 mW. *Caution - Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. *IEC is a registered trademark of the International Electrotechnical Commision. © 2013 EMCORE Corporation | REV 2013.11 +1 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.