5100 Series L-Band Fiber Optic Links DATASHEET | OCTOBER 2012 SATCOM The 5100-Series fiber optic inter-facility links (IFLs) are a high performance, cost-effective alternative to coaxial cable for 950 MHz to 2050 MHz L-Band satellite communications applications. EMCORE’s fiber optic IFLs, function as transparent links between satellite antennas and Network Operations Centers (NOC). These IFLs eliminate the limitations of copper systems by enabling longer transmission distance while retaining the highest level of signal quality. Features 950 MHz – 2050 MHz Up to eight plug-in cards per 3u chassis Up to four flange-mount modules per 1u chassis 50 ohm SMA and 75 ohm Type Options Affordable replacement for coaxial systems Applications In addition, EMCORE’s fiber optics provide several other significant network advantages, including simplified network design, ease of installation, and immunity from EMI/RFI and lightning. They are available either in a flange-mount package for outdoor applications or as a plug-in for integration with EMCORE’s System 10000 rack-mount chassis. Performance Highlights Minimum Typical Maximum Units Wavelength - 1310 - nm Transmitter Optical Output Power - 0 - dBm Receiver Optical Input Power - -12 - dBm Link Gain @ 1 dB optical loss Standard High - -4 13 - dB TVRO Broadcast Earth Stations Temperature Range Flange Mount Rack Mount -40 0 - +65 +50 ˚C ˚C Headends Frequency Range 950 - 2050 MHz VSAT GPS Radios See following pages for complete specifications and conditions. Package Options Transmitter Receiver Rack Mount 950 - 1450 MHz 950 - 1750 MHz 950 - 2150 MHz 10346A 10346B 10347A 10446A 10446B 10447A Flange Mount 950 - 1450 MHz 950 - 1750 MHz 950 - 2150 MHz 3110A 3111A 3112A 4110A 4111A 4112A 1 1. Rack mount package for System 10000 platform only © 2012 EMCORE Corporation | REV 2012.10 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5100 Series L-Band Fiber Optic Links DATASHEET | OCTOBER 2012 SATCOM Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Condition Min Max Units -40 0 +65 +50 ˚C ˚C -40 -40 +85 +85 ˚C ˚C VDC Operating Temperature Range Flange-mount Rack-mount TOP - Storage Temperature Flange-mount Rack-mount TSTG - DC Voltage - - - 24 DC Current (Transmitter) - +8VDC 250 - mA DC Current (Receiver) - +8 VDC 200 - mA Link Characteristics, 1 dB Optical Electrical / Optical Characteristics L-Band Performance Symbol Min Type Max Units Wavelength (Transmitter) - - 1290 - 1340 nm Link Gain - Std. Low High Optical Output Power (Transmitter) - - - 1 - mW 50 Ohm (At 25° C), min. - -4.00 dB -15.00 dB +13.00 dB dc Responsivity (Receiver) - - 0.75 - - A/W 75 Ohm (At 25° C), min. - -4.00 dB -15.00 dB +13.00 dB - Corning SMF-28 or equivalent - - - - - FC/APC Tight Fit, (Seikoh Giken or equivalent) - - - - - - 60 - - dB Fiber Connector Connector Return Loss Condition Parameter Parameter Parameter Performance Tx Gain Option Gain vs. temp. (typ.) - Std. -002 (high) - Std. -002 (low) Tx Gain (TG) - 50 Ohm - -19.50 dB -2.50 dB Rx Gain (RG) - 50Ohm - +21.00 dB +4.00 dB - -17.75 dB -0.75 dB Rx Gain (RG) - 75 Ohm - +19.25 dB +2.25 dB Noise figure, max - 45 dB 28 dB Gain vs. temp. (typ.) - 0.06 dB/°C 0.03 dB/°C Input IP3, min. -20° C -40° C +7.5 dBm +4.5 dBm -9.5 dBm -12.5 dBm Input 1 dB compression, typical –20° C -40° C ≥ 0 dBm ≥ -3 dBm ≥ -17 dBm ≥ -20 dBm Amplitude flatness any 500 MHz any 40 MHz Gain vs. temp. (typ.) - 0.09 dB/°C 0.12 dB/°C Max RF input (Tx) - +3 dBm -14 dBm VSWR Input Impedance - ± 0.75 dB 0.03 dB/°C Performance Rx gain option Tx Gain (TG) - 75 Ohm Amplitude flatness any 500 MHz any 40 MHz ± 1.50 dB ± 0.35 dB RF Characteristics, Rx RF Characteristics, Tx Parameter Amplitude flatness any 500 MHz any 40 MHz VSWR Output Impedance ± 0.75 dB ± 0.15 dB Output 1.8:1 - 75 Ohm F, (50 Ohm SMA, option –001) ± 0.75 dB ± 0.20 dB Input 2.0:1 - 75 Ohm F, (50 Ohm SMA, option –001) © 2012 EMCORE Corporation | REV 2012.10 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5100 Series L-Band Fiber Optic Links DATASHEET | OCTOBER 2012 SATCOM Device Resistance and Voltage for Rx Optical Power and DC Electrical Power Monitor Outputs (See Figures 1 and 2) Version Voltage Resistance Tx/Rx 5V 333 Ω ALARM VCC VCC Orange Wire Open if <0.1 mW (approx.): Sinks < 10 mA if > 0.1 mW Figure 1. Receiver Electrical Schematic for Power Alarm Figure 2. Schematic for DC Power Monitor (Flange Mount Units Only) DC Voltage Pin Information Flange Mount Package Rack Mount Package: Used with the 10990A 3u Rack Mount Chassis) Input Voltage 12 V 1,2 15 V 1,2 18 V 1,2 24 V 1,2 Plug-in Tx 170 mA 135 mA 115 mA 85 mA D-Sub Rx 150 mA 120 mA 100 mA 75 mA 1. Applies to All Versions Except –003) 2. Ripple and noise: 100 mVp-p >100 kHz; 200 mVp-p <100 kHz Flange Mount Package Lead Color Tx Rx Red +8 to +24 volts +8 to +24 volts Brown Not used Low optical power alarm Orange DC power monitor DC power monitor Yellow Not Used Photodiode current monitor 1 V/mA Black GND GND © 2012 EMCORE Corporation | REV 2012.10 Tx Plug-in Rx Plug-in 13 +15 volts +15 volts 2 nc nc 3 nc nc 4 GND GND 5 GND GND 64 nc Photodiode current Monitor. (1 V/mA) 74 nc Low optical power alarm 8 LNB DC Output nc 94 Connects to RF center pin for powering LNB nc 4 3. Powered from 10901G, or equivalent power supply 4. Accessible via connector on back panel of 10990A chassis 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5100 Series L-Band Fiber Optic Links DATASHEET | OCTOBER 2012 SATCOM Ordering Code Definitions - Transmitters Option Option Availability Flange Mount Option Description Standard Configuration Plug-in -001 X X 50 Ω SMA, female 75 Ω F-type connector, female -002 X X Two-stage RF Pre-amp Single stage RF Pre-amp -003 X Unit to run from + 5.0 V ± 0.2V No internal DC regulator Internal DC regulator operates from +8V to +24 V input -004 X No LNB voltage on center pin DC voltage on center pin for LNB powering 75 Ω CANARE BNC, female 75 Ω F-type connector, female -006 X Ordering Code Definitions - Receivers Option Option Availability Flange Mount Option Description Standard Configuration Plug-in -001 X X 50 Ω SMA, female 75 Ω F-type connector, female -002 X X Single stage RF Post-amp Two-stage RF Post-amp. -003 X Unit to run from + 5.0 V ± 0.2V No internal DC regulator Internal DC regulator operates from +8V to +24 V input -004 X No DC voltage on center pin DC voltage on center pin 75 Ω CANARE BNC, female 75 Ω F-type connector, female -006 X Mounting Options Part / Number Model Description Capacity 1260-001-001 NEMA enclosure (12” x 12” x4”) Up to 2 flange-mount modules 1260-001-001 1U 19” rack mount chassis (1.75” x19” x 18”) Up to 4 flange-mount modules 1261-002-001 1U 19” rack mount chassis & internal power supply Up to 4 flange-mount modules 10990A 10901G 10901G 3U 19” rack mount chassis 3U, plug-in power supply (90-260 VAC input) 3U, auxiliary plug-in power supply (90-260 VAC input) Up to 8 plug-in modules Laser Safety This product meets the appropriate standard in Title 21 of the Code of Federal Regulations (CFR). FDA/CDRH Class 1 laser product. This device has been classified with the FDA/CDRH under accession number 0220191. All versions of this laser are Class 1 laser product, tested according to IEC 60825-1:2007 / EN 60825-1:2007. Wavelength = 1.3 μm. Maximum power = 30 mW. Caution: Use of controls, adjustments and procedures other than those specified herein may result in hazardous laser radiation exposure. © 2012 EMCORE Corporation | REV 2012.10 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice. 5100 Series L-Band Fiber Optic Links DATASHEET | OCTOBER 2012 SATCOM Rack Mount Package Receiver package depicted below. Transmitter plug-in has only “Power On” indicator LED. Flange Mount Package © 2012 EMCORE Corporation | REV 2012.10 626-293-3400 [email protected] www.emcore.com Information contained herein is deemed to be reliable and accurate as of the issue date. EMCORE reserves the right to change the design or specifications at any time without notice.