SAW Components SAW IF filter GSM Base Station Series/type: Ordering code: B5233 B39141B5233H810 Date: Version: Jun 30, 2011 2.0 EPCOS AG 2011. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the information contained therein without EPCOS’ prior express consent is prohibited. SAW Components B5233 138.2 MHz SAW IF filter Data Sheet Application ■ Low-loss IF filter for GSM applications ■ Usable passband 35 MHz ■ Balanced operation Features ■ ■ ■ ■ ■ ■ ■ ■ ■ Package size 7.0 x 5.0 x 1.33 mm3 Package code QCC12E RoHS compatible Approx. weight 0.25 g Ceramic package for Surface Mount Technology (SMT) Ni, gold-plated terminals Electrostatic Sensitive Device (ESD) Filter surface passivated Moisture Sensitivity Level 1 Pin configuration ■ ■ ■ ■ 10, 12 4, 6 1,5,7,11 2,3,8,9 Input Output Case Ground To be grounded 1,5,7,11 Please read cautions and warnings and important notes at the end of this document. 2 Jun 30, 2011 SAW Components B5233 138.2 MHz SAW IF filter Data Sheet Characteristics Operating temperature range: Terminating source impedance: Terminating load impedance: T = –40 to 85 ˚C ZS = 200 Ω balanced and matching network ZL = 200 Ω balanced and matching network min. Nominal frequency fN — typ. @ 25 ˚C 138.2 max. Minimum insertion attenuation (including matching network) αmin — 10.4 12 35.0 41 — MHz — 0.7 1.4 dB — 30 100 ns 40 40 45 58 44 60 — — — dB dB dB — 0.540 1.0 µs — -75 — ppm/K — MHz dB Passband width αrel < 1.2 dB Amplitude ripple (p-p) fN ± 17.6 MHz Group delay ripple (p-p) fN ± 17.6 MHz Β1.2dB ∆α ∆τ Relative attenuation (relative to αmin) 28.00 MHz ... 64.00 MHz 212.0 MHz ... 464.0 MHz 464.0 MHz ... 3000 MHz αrel Average group delay τmean fN ± 17.6 MHz Temperature coefficient of frequency Please read cautions and warnings and important notes at the end of this document. TCf 3 Jun 30, 2011 SAW Components B5233 138.2 MHz SAW IF filter Data Sheet Matching network to 200 Ω balanced input - 200 Ω balanced output Ls2 Ls1 Lp1 200 Ω 200 Ω Lp2 Ls2 Ls1 Ls2 = 47 nH Lp2 = 120 nH Ls1 = 100 nH Lp1 = 120 nH (Element values depend upon PCB properties and layout) Maximum ratings Operable temperature range Storage temperature range DC voltage Input power at 120.6-155.8 MHz T Tstg VDC PIN Please read cautions and warnings and important notes at the end of this document. –40/+85 –55/+125 0 20 4 ˚C ˚C V dBm Jun 30, 2011 CW SAW Components B5233 138.2 MHz SAW IF filter Data Sheet Transfer function (S21, wideband, normalised) Transfer function (S21, narrowband, normalised) Please read cautions and warnings and important notes at the end of this document. 5 Jun 30, 2011 SAW Components B5233 138.2 MHz SAW IF filter Data Sheet References Type B5233 Ordering code B39141B5233H810 Marking and package C61157-A7-A103 Packaging F61074-V8170-Z000 Date codes L_1126 S-parameters B5233_NB.s2p; B5233_WB.s2p Soldering profile S_6001 RoHS compatible defined as compatible with the following documents: "DIRECTIVE 2002/95/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 2005/618/EC from April 18th, 2005, amending Directive 2002/95/EC of the European Parliament and of the Council for the purposes of establishing the maximum concentration values for certain hazardous substances in electrical and electronic equipment." Matching coils See Inductor pdf-catalog http://www.tdk.co.jp/tefe02/coil.htm#aname1 and Data Library for circuit simulation http://www.tdk.co.jp/etvcl/index.htm For further information please contact your local EPCOS sales office or visit our webpage at www.epcos.com . Published by EPCOS AG Systems, Acoustics, Waves Business Group P.O. Box 80 17 09, 81617 Munich, GERMANY EPCOS AG 2011. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices. Please read cautions and warnings and important notes at the end of this document. 6 Jun 30, 2011 Important notes The following applies to all products named in this publication: 1. 2. 3. 4. 5. 6. 7. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. We also point out that in individual cases, a malfunction of electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of an electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of an electronic component. The warnings, cautions and product-specific notes must be observed. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the foregoing for customer-specific products. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSMP, CSSP, CTVS, DeltaCap, DigiSiMic, DSSP, FormFit, MiniBlue, MiniCell, MKD, MKK, MLSC, MotorCap, PCC, PhaseCap, PhaseCube, PhaseMod, PhiCap, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SiMic, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. 7 Jun 30, 2011