TI TLVH431BQDBZR

 SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
D Low-Voltage Operation . . . Down to 1.24 V
D Reference Voltage Tolerances at 255C
D
D
− 0.5% for B Grade
− 1% for A Grade
− 1.5% for Standard Grade
Adjustable Output Voltage, VO = VREF to 18 V
Wide Operating Cathode Current Range . . .
55 µA to 80 mA
TLVH431
DBV (SOT23-5) PACKAGE
(TOP VIEW)
NC
*NC
CATHODE
1
5
ANODE
4
REF
D 0.25-Ω Typical Output Impedance
D −405C to 1255C Specifications
D TLVH432 Provides Alternative Pinouts for
D
SOT-23-3 and SOT-89 Packages
Ultra-Small SC-70 Package Offers 40%
Smaller Footprint Than SOT-23-3
TLVH431
DBZ (SOT23-3) PACKAGE
(TOP VIEW)
REF
1
CATHODE
2
2
3
3
ANODE
NC - No internal connection
* Pin 2 is connected internally to ANODE
(die substrate). Pin 2 should be
connected to ANODE or left floating.
TLVH431
DCK (SC-70) PACKAGE
(TOP VIEW)
CATHODE
NC
REF
1
6
2
5
3
4
TLVH431
PK (SOT-89) PACKAGE
(TOP VIEW)
TLVH431
LP (TO-92/TO-226) PACKAGE
(TOP VIEW)
CATHODE
ANODE
NC
NC
CATHODE
ANODE
ANODE
REF
NC - No internal connection
REF
TLVH432
PK (SOT-89) PACKAGE
(TOP VIEW)
REF
TLVH432
DBZ (SOT23-3) PACKAGE
(TOP VIEW)
CATHODE
1
REF
2
3
ANODE
ANODE
ANODE
ANODE
CATHODE
description/ordering information
The TLVH431 and TLVH432 are low-voltage 3-terminal adjustable voltage references with specified thermal
stability over applicable industrial and commercial temperature ranges. Output voltage can be set to any value
between VREF (1.24 V) and 18 V with two external resistors (see Figure 2). These devices operate from a lower
voltage (1.24 V) than the widely used TL431 and TL1431 shunt-regulator references.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright  2005, Texas Instruments Incorporated
!" # $%&" !# '%()$!" *!"&+
*%$"# $ " #'&$$!"# '& ",& "&# &-!# #"%&"#
#"!*!* .!!"/+ *%$" '$&##0 *&# " &$&##!)/ $)%*&
"&#"0 !)) '!!&"&#+
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
description/ordering information (continued)
When used with an optocoupler, the TLVH431 and TLVH432 are ideal voltage references in isolated feedback
circuits for 3-V to 3.3-V switching-mode power supplies. They have a typical output impedance of 0.25 Ω. Active
output circuitry provides a very sharp turn-on characteristic, making the TLVH431 and TLVH432 excellent
replacements for low-voltage Zener diodes in many applications, including on-board regulation and adjustable
power supplies.
The TLVH432 is identical to the TLVH431, but is offered with different pinouts for the SOT23-3 and SOT-89
packages.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
ORDERING INFORMATION
TJ
VREF
TOLERANCE
ORDERABLE
PART NUMBER
PACKAGE†
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 3000
TLVH431BCDCKR
Reel of 250
TLVH431BCDCKT
Reel of 3000
TLVH431BCDBVR
Reel of 250
TLVH431BCDBVT
TLVH431BCDBZR
Reel of 3000
0.5%
SOT-23-3 (DBZ)
TO-92 (LP)
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 1000
Y3J_
PREVIEW
Y3J_
PREVIEW
TLVH432BCDBZT
TLVH431BCPK
SOT-89 (PK)
YH_
TLVH432BCDBZR
TLVH431BCDBZT
Reel of 250
TOP-SIDE
MARKING‡
TLVH432BCPK
Bulk of 1000
TLVH431BCLP
Reel of 2000
TLVH431BCLPR
Reel of 3000
TLVH431ACDCKR
Reel of 250
TLVH431ACDCKT
Reel of 3000
TLVH431ACDBVR
Reel of 250
TLVH431ACDBVT
PREVIEW
ZA431B
PREVIEW
PREVIEW
TLVH431ACDBZR
Reel of 3000
0°C to 70°C
1%
SOT-23-3 (DBZ)
TLVH432ACDBZR
TLVH431ACDBZT
Reel of 250
TLVH432ACDBZT
TLVH431ACPK
SOT-89 (PK)
TO-92 (LP)
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 1000
PREVIEW
TLVH432ACPK
Bulk of 1000
TLVH431ACLP
Reel of 2000
TLVH431ACLPR
Reel of 3000
TLVH431CDCKR
Reel of 250
TLVH431CDCKT
Reel of 3000
TLVH431CDBVR
Reel of 250
TLVH431CDBVT
PREVIEW
PREVIEW
PREVIEW
PREVIEW
TLVH431CDBZR
Reel of 3000
1.5%
SOT-23-3 (DBZ)
TLVH432CDBZR
TLVH431CDBZT
Reel of 250
PREVIEW
TLVH432CDBZT
TLVH431CPK
SOT-89 (PK)
TO-92 (LP)
Reel of 1000
TLVH432CPK
PREVIEW
Bulk of 1000
TLVH431CLP
PREVIEW
Reel of 2000
TLVH431CLPR
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
‡ DBV/DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
ORDERING INFORMATION (continued)
TJ
VREF
TOLERANCE
ORDERABLE
PART NUMBER
PACKAGE†
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 3000
TLVH431BIDCKR
Reel of 250
TLVH431BIDCKT
Reel of 3000
TLVH431BIDBVR
Reel of 250
TLVH431BIDBVT
TLVH431BIDBZR
Reel of 3000
0.5%
SOT-23-3 (DBZ)
TO-92 (LP)
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 1000
Y3K_
PREVIEW
Y3K_
PREVIEW
TLVH432BIDBZT
TLVH431BIPK
SOT-89 (PK)
YJ_
TLVH432BIDBZR
TLVH431BIDBZT
Reel of 250
TOP-SIDE
MARKING‡
TLVH432BIPK
Bulk of 1000
TLVH431BILP
Reel of 2000
TLVH431BILPR
Reel of 3000
TLVH431AIDCKR
Reel of 250
TLVH431AIDCKT
Reel of 3000
TLVH431AIDBVR
Reel of 250
TLVH431AIDBVT
PREVIEW
ZB431B
PREVIEW
PREVIEW
TLVH431AIDBZR
Reel of 3000
−40°C to 85°C
1%
SOT-23-3 (DBZ)
TLVH432AIDBZR
TLVH431AIDBZT
Reel of 250
TLVH432AIDBZT
TLVH431AQPK
SOT-89 (PK)
TO-92 (LP)
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 1000
TLVH432AQPK
Bulk of 1000
TLVH431AILP
Reel of 2000
TLVH431AILPR
Reel of 3000
TLVH431IDCKR
Reel of 250
TLVH431IDCKT
Reel of 3000
TLVH431IDBVR
Reel of 250
TLVH431IDBVT
TLVH431IDBZR
Reel of 3000
1.5%
SOT-23-3 (DBZ)
TLVH432IDBZR
TLVH431IDBZT
Reel of 250
TLVH432IDBZT
TLVH431QPK
SOT-89 (PK)
TO-92 (LP)
Reel of 1000
PREVIEW
TLVH432IPK
Bulk of 1000
TLVH431ILP
Reel of 2000
TLVH431ILPR
PREVIEW
PREVIEW
PREVIEW
PREVIEW
PREVIEW
PREVIEW
PREVIEW
PREVIEW
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
‡ DBV/DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
ORDERING INFORMATION (continued)
TJ
VREF
TOLERANCE
ORDERABLE
PART NUMBER
PACKAGE†
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 3000
TLVH431BQDCKR
Reel of 250
TLVH431BQDCKT
Reel of 3000
TLVH431BQDBVR
Reel of 250
TLVH431BQDBVT
TLVH431BQDBZR
Reel of 3000
0.5%
SOT-23-3 (DBZ)
TO-92 (LP)
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 1000
Y3L_
PREVIEW
Y3L_
PREVIEW
TLVH432BQDBZT
TLVH431BQPK
SOT-89 (PK)
YK_
TLVH432BQDBZR
TLVH431BQDBZT
Reel of 250
TOP-SIDE
MARKING‡
TLVH432BQPK
Bulk of 1000
TLVH431BQLP
Reel of 2000
TLVH431BQLPR
Reel of 3000
TLVH431AQDCKR
Reel of 250
TLVH431AQDCKT
Reel of 3000
TLVH431AQDBVR
Reel of 250
TLVH431AQDBVT
PREVIEW
ZD431B
PREVIEW
PREVIEW
TLVH431AQDBZR
Reel of 3000
−40°C to 125°C
1%
SOT-23-3 (DBZ)
TLVH432AQDBZR
TLVH431AQDBZT
Reel of 250
TLVH432AQDBZT
TLVH431AQPK
SOT-89 (PK)
TO-92 (LP)
SC-70 (DCK)
SOT-23-5 (DBV)
Reel of 1000
PREVIEW
TLVH432AQPK
Bulk of 1000
TLVH431AQLP
Reel of 2000
TLVH431AQLPR
Reel of 3000
TLVH431QDCKR
Reel of 250
TLVH431QDCKT
Reel of 3000
TLVH431QDBVR
Reel of 250
TLVH431QDBVT
PREVIEW
PREVIEW
PREVIEW
PREVIEW
TLVH431QDBZR
Reel of 3000
1.5%
SOT-23-3 (DBZ)
TLVH432QDBZR
TLVH431QDBZT
Reel of 250
TLVH432QDBZT
TLVH431QPK
SOT-89 (PK)
TO-92 (LP)
Reel of 1000
PREVIEW
TLVH432QPK
Bulk of 1000
TLVH431QLP
Reel of 2000
TLVH431QLPR
PREVIEW
PREVIEW
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
‡ DBV/DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
logic block diagram
CATHODE
REF
+
−
VREF = 1.24 V
ANODE
equivalent schematic
Cathode
REF
Anode
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Cathode voltage, VKA (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
Cathode current range, IK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −25 mA to 80 mA
Reference current range, Iref . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.05 mA to 3 mA
Package thermal impedance, θJA (see Notes 2 and 3): DBV package . . . . . . . . . . . . . . . . . . . . . . . . 206°C/W
DBZ package . . . . . . . . . . . . . . . . . . . . . . . . 206°C/W
DCK package . . . . . . . . . . . . . . . . . . . . . . . . 252°C/W
LP package . . . . . . . . . . . . . . . . . . . . . . . . . . 140°C/W
PK package . . . . . . . . . . . . . . . . . . . . . . . . . . . 52°C/W
Operating virtual junction temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to the anode terminal, unless otherwise noted.
2. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
3. The package thermal impedance is calculated in accordance with JESD 51-7.
recommended operating conditions
VKA
Cathode voltage
IK
Cathode current (continuous)
TLVH43X_C
TA
Operating free-air temperature range
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MIN
MAX
VREF
18
V
0.1
80
mA
0
70
TLVH43X_I
−40
85
TLVH43X_Q
−40
125
UNIT
°C
C
7
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
TLVH431 electrical characteristics at 25°C free-air temperature (unless otherwise noted)
TLVH431, TLVH432
PARAMETER
TEST CONDITIONS
TA = 25°C
VREF
VKA = VREF,
IK = 10 mA
Reference voltage
TA = full range
(see Note 4 and
Figure 1)
VREF(dev)
VKA = VREF, IK = 10 mA
(see Note 4 and Figure 1)
∆VREF
∆VKA
Ratio of VREF change to cathode
voltage change
IK = 10 mA
(see Figure 2)
Iref
Reference terminal current
IK = 10 mA, R1 = 10 kΩ, R2 = open
(see Figure 2)
Iref(dev)
Iref deviation over full temperature
range (see Note 5)
IK = 10 mA, R1 = 10 kΩ, R2 = open
(see Note 4 and Figure 2)
IK(min)
Minimum cathode current for
regulation
IK(off)
Off-state cathode current
|zKA|
Dynamic impedance
(see Note 6)
VREF = 0, VKA = 18 V (see Figure 3)
VKA = VREF, f ≤ 1 kHz,
IK = 0.1 mA to 80 mA (see Figure 1)
MAX
1.222
1.24
1.258
1.21
1.27
TLVH431I
1.202
1.278
TLVH431Q
1.194
UNIT
V
1.286
4
12
TLVH431I
6
20
TLVH431Q
11
31
-1.5
-2.7
mV/V
0.1
0.5
µA
TLVH431C
0.05
0.3
TLVH431I
0.1
0.4
TLVH431Q
0.15
0.5
60
100
µA
0.02
0.1
µA
0.25
0.4
Ω
VKA = VREF to 18 V
VKA = VREF (see Figure 1)
TYP
TLVH431C
TLVH431C
VREF deviation over full
temperature range (see Note 5)
MIN
mV
µA
NOTES: 4. Full temperature ranges are: − 40°C to 125°C for TLVH431Q, − 40°C to 85°C for TLVH431I, and 0°C to 70°C for the TLVH431C.
5. The deviation parameters VREF(dev) and Iref(dev) are defined as the differences between the maximum and minimum values obtained
over the rated temperature range. The average full-range temperature coefficient of the reference input voltage, αVREF,
is defined as:
V
REF(dev)
10 6
VREF (T A+25°C)
ŤαV REFŤ ppm +
∆T
°C
A
ǒ Ǔ
ǒ
Ǔ
where ∆TA is the rated operating free-air temperature range of the device.
αVREF can be positive or negative, depending on whether minimum VREF or maximum VREF, respectively, occurs at the
lower temperature.
∆V
KA
6. The dynamic impedance is defined as: z
+
ka
∆I
K
Ť Ť
When the device is operating with two external resistors (see Figure 2), the total dynamic impedance of the circuit is defined
as:
z
+ ∆V [ z
1 ) R1
ka
ka
∆I
R2
Ť Ť
8
Ť Ť
ǒ
Ǔ
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
TLVH431A electrical characteristics at 25°C free-air temperature (unless otherwise noted)
PARAMETER
TLVH431A
TLVH432A
TEST CONDITIONS
TA = 25°C
VREF
VKA = VREF,
IK = 10 mA
Reference voltage
VREF(dev)
VREF deviation over full
temperature range (see Note 5)
TA = full range
(see Note 4 and
Figure 1)
VKA = VREF, IK = 10 mA
(see Note 4 and Figure 1)
∆VREF
∆VKA
Ratio of VREF change to cathode
voltage change
IK = 10 mA
(see Figure 2)
Iref
Reference terminal current
IK = 10 mA, R1 = 10 kΩ, R2 = open
(see Figure 2)
Iref(dev)
Iref deviation over full temperature
range (see Note 5)
IK = 10 mA, R1 = 10 kΩ, R2 = open
(see Note 4 and Figure 2)
IK(min)
Minimum cathode current for
regulation
UNIT
MIN
TYP
MAX
1.228
1.24
1.252
TLVH431AC
1.221
1.259
TLVH431AI
1.215
1.265
TLVH431AQ
1.209
V
1.271
TLVH431AC
4
12
TLVH431AI
6
20
TLVH431AQ
11
31
-1.5
-2.7
mV/V
0.1
0.5
µA
TLVH431AC
0.05
0.3
TLVH431AI
0.1
0.4
TLVH431AQ
0.15
0.5
60
100
VKA = VREF to 18 V
VKA = VREF (see Figure 1)
mV
µA
µA
VREF = 0, VKA = 18 V (see Figure 3)
0.02
0.1
µA
Dynamic impedance
VKA = VREF, f ≤ 1 kHz,
|zKA|
0.25
0.4
Ω
(see Note 6)
IK = 0.1 mA to 80 mA (see Figure 1)
NOTES: 4. Full temperature ranges are: − 40°C to 125°C for TLVH431AQ, − 40°C to 85°C for TLVH431AI, and 0°C to 70°C for the TLVH431AC.
5. The deviation parameters VREF(dev) and Iref(dev) are defined as the differences between the maximum and minimum values obtained
over the rated temperature range. The average full-range temperature coefficient of the reference input voltage, αVREF,
is defined as:
V
REF(dev)
10 6
VREF (T A+25°C)
ppm
ŤαV REFŤ
+
∆T
°C
A
IK(off)
Off-state cathode current
ǒ Ǔ
ǒ
Ǔ
where ∆TA is the rated operating free-air temperature range of the device.
αVREF can be positive or negative, depending on whether minimum VREF or maximum VREF, respectively, occurs at the
lower temperature.
∆V
KA
6. The dynamic impedance is defined as: z
+
ka
∆I
K
Ť Ť
When the device is operating with two external resistors (see Figure 2), the total dynamic impedance of the circuit is defined
as:
z
+ ∆V [ z
1 ) R1
ka
ka
∆I
R2
Ť Ť
Ť Ť
ǒ
Ǔ
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
9
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
TLVH431B electrical characteristics at 25°C free-air temperature (unless otherwise noted)
PARAMETER
TLVH431B
TLVH432B
TEST CONDITIONS
TA = 25°C
VREF
Reference voltage
VREF(dev)
∆VREF
∆VKA
Iref
VKA = VREF,
IK = 10 mA
VREF deviation over full
temperature range (see Note 5)
TA = full range
(see Note 4 and
Figure 1)
VKA = VREF, IK = 10 mA
(see Note 4 and Figure 1)
Ratio of VREF change to cathode
voltage change
IK = 10 mA
(see Figure 2)
Reference terminal current
IK = 10 mA, R1 = 10 kΩ (see Figure 2)
Iref deviation over full temperature
range (see Note 5)
IK(min)
Minimum cathode current for
regulation
IK(off)
Off-state cathode current
|zKA|
Dynamic impedance
(see Note 6)
VKA = VREF (see Figure 1)
VREF = 0, VKA = 18 V (see Figure 3)
VKA = VREF, f ≤ 1 kHz,
IK = 0.1 mA to 80 mA (see Figure 1)
MAX
1.234
1.24
1.246
1.227
1.253
TLVH431BI
1.224
1.259
TLVH431BQ
1.221
V
1.265
TLVH431BC
4
12
TLVH431BI
6
20
TLVH431BQ
11
31
-1.5
-2.7
mV/V
µA
VKA = VREF to 18 V
IK = 10 mA, R1 = 10 kΩ, R2 = open
(see Note 4 and Figure 2)
TYP
TLVH431BC
mV
0.1
0.5
0.05
0.3
TLVH431BI
0.1
0.4
TLVH431BQ
0.15
0.5
60
100
µA
0.02
0.1
µA
0.25
0.4
Ω
TLVH431BC
Iref(dev)
UNIT
MIN
µA
NOTES: 4. Full temperature ranges are: − 40°C to 125°C for TLVH431BQ, − 40°C to 85°C for TLVH431BI, and 0°C to 70°C for the TLVH431BC.
5. The deviation parameters VREF(dev) and Iref(dev) are defined as the differences between the maximum and minimum values obtained
over the rated temperature range. The average full-range temperature coefficient of the reference input voltage, αVREF,
is defined as:
V
REF(dev)
10 6
VREF (T A+25°C)
ŤαV REFŤ ppm +
∆T
°C
A
ǒ Ǔ
ǒ
Ǔ
where ∆TA is the rated operating free-air temperature range of the device.
αVREF can be positive or negative, depending on whether minimum VREF or maximum VREF, respectively, occurs at the
lower temperature.
∆V
KA
6. The dynamic impedance is defined as: z
+
ka
∆I
K
Ť Ť
When the device is operating with two external resistors (see Figure 2), the total dynamic impedance of the circuit is defined
as:
z
+ ∆V [ z
1 ) R1
ka
ka
∆I
R2
Ť Ť
10
Ť Ť
ǒ
Ǔ
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION
Input
VO
Input
VO
IK
IK
R1
R2
VREF
Figure 1. Test Circuit for VKA = VREF,
VO = VKA = VREF
Input
Iref
VREF
Figure 2. Test Circuit for VKA > VREF,
VO = VKA = VREF × (1 + R1/R2) + Iref × R1
VO
IK(off)
Figure 3. Test Circuit for IK(off)
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
11
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION
REFERENCE VOLTAGE
vs
JUNCTION TEMPERATURE
1.254
IK = 10 mA
V ref − Reference Voltage − V
1.252
1.250
1.248
1.246
1.244
1.242
1.240
1.238
−50
−25
0
25
50
75
100
125
150
TJ − Junction Temperature − °C
Figure 4
REFERENCE INPUT CURRENT
vs
JUNCTION TEMPERATURE
250
230
210
IK = 10 mA
R1 = 10 kΩ
R2 = Open
190
170
150
130
110
90
70
50
−50
−25
0
25
50
75
100
125
Figure 5
12
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
150
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION†
CATHODE CURRENT
vs
CATHODE VOLTAGE
CATHODE CURRENT
vs
CATHODE VOLTAGE
80
250
VKA = VREF
TA = 25°C
200
VKA = VREF
TA = 25°C
10
I K − Cathode Current − µ A
5
0
−5
100
50
0
−50
−100
−150
−10
−200
−15
−1
−0.5
0
0.5
1
VKA − Cathode Voltage − V
−250
−1
1.5
−0.5
0
0.5
1
VKA − Cathode Voltage − V
Figure 6
1.5
Figure 7
OFF-STATE CATHODE CURRENT
vs
JUNCTION TEMPERATURE
4000
I K(off) − Off-State Cathode Current − nA
I K − Cathode Current − mA
150
VKA = 5 V
VREF = 0
3500
3000
2500
2000
1500
1000
500
0
−50
−25
0
25
50
75
100
125
150
TJ − Junction Temperature − °C
Figure 8
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
13
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION†
RATIO OF DELTA REFERENCE VOLTAGE
TO DELTA CATHODE VOLTAGE
vs
JUNCTION TEMPERATURE
∆V ref/ ∆V KA − Ratio of Delta Reference Voltage
to Delta Cathode Voltage − mV/V
0
−0.0
IK = 10 mA
∆VKA = VREF to 18 V
−0.1
−0.2
−0.3
−0.4
−0.5
−0.6
−0.7
−0.8
−0.9
−1
−1.0
−50
−25
0
25
50
75
100
125
150
TJ − Junction Temperature − °C
Figure 9
PERCENTAGE CHANGE IN VREF
vs
OPERATING LIFE AT 55°C
0.025
V ref − %
Percentage Change in Vref
IK = 1 mA
0
% Change (avg)
− 0.025
% Change (3δ)
− 0.05
− 0.075
− 0.1
% Change (−3δ)
− 0.125
0
10
20
30
40
50
Operating Life at 55°C − kh†
60
† Extrapolated from life-test data taken at 125°C; the activation energy
assumed is 0.7 eV.
Figure 10
† Operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
3V
Vn − Equivalent Input Noise Voltage − nV/ Hz
350
VKA = VREF
IK = 1 mA
TA = 25°C
1 kΩ
300
470 µF
+
250
TLVH431
TLVH432
750 Ω
2200 µF
+
820 Ω
TLE2027
+
_
TP
160 kΩ
160 Ω
200
150
10
TEST CIRCUIT FOR EQUIVALENT INPUT NOISE VOLTAGE
100
1k
10 k
100 k
f – Frequency – Hz
Figure 11
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
15
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION
EQUIVALENT INPUT NOISE VOLTAGE
OVER A 10-SECOND PERIOD
Vn − Equivalent Input Noise Voltage − µ V
10
f = 0.1 Hz to 10 Hz
IK = 1 mA
TA = 25°C
8
6
4
2
0
−2
−4
−6
−8
−10
0
2
4
6
8
10
t − Time − s
3V
1 kΩ
470 µF
+
750 Ω
0.47 µF
2200 µF
+
820 Ω
TLVH431
TLVH432
TLE2027
10 kΩ
+
_
10 kΩ
1 µF
160 kΩ
TLE2027
+
_
2.2 µF
+
CRO 1 MΩ
33 kΩ
16 Ω
0.1 µF
33 kΩ
TEST CIRCUIT FOR 0.1-Hz TO 10-Hz EQUIVALENT NOISE VOLTAGE
Figure 12
16
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
TP
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION
80
0°
IK = 10 mA
TA = 25°C
70
36°
60
72°
50
108°
40
144°
30
180°
Phase Shift
A V − Small-Signal Voltage Gain/Phase Margin − dB
SMALL-SIGNAL VOLTAGE GAIN
/PHASE MARGIN
vs
FREQUENCY
Output
IK
6.8 kΩ
180 Ω
10 µF
5V
4.3 kΩ
20
10
GND
0
−10
−20
100
TEST CIRCUIT FOR VOLTAGE GAIN
AND PHASE MARGIN
1k
10 k
100 k
1M
f − Frequency − Hz
Figure 13
REFERENCE IMPEDANCE
vs
FREQUENCY
100
|z ka | − Reference Impedance − Ω
IK = 0.1 mA to 80 mA
TA = 25°C
100 Ω
Output
10
IK
100 Ω
1
+
−
GND
0.1
TEST CIRCUIT FOR REFERENCE IMPEDANCE
0.01
1k
10 k
100 k
1M
10 M
f − Frequency − Hz
Figure 14
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
17
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION
PULSE RESPONSE 1
3.5
3
Input and Output Voltage − V
R = 18 kΩ
TA = 25°C
Input
18 kΩ
Output
2.5
Ik
2
1.5
Pulse
Generator
f = 100 kHz
Output
50 Ω
1
GND
0.5
0
TEST CIRCUIT FOR PULSE RESPONSE 1
−0.5
0
1
2
3
4
5
6
7
8
t − Time − µs
Figure 15
PULSE RESPONSE 2
3.5
3
Input and Output Voltage − V
R = 1.8 kΩ
TA = 25°C
Input
1.8 kΩ
Output
2.5
IK
2
1.5
Pulse
Generator
f = 100 kHz
Output
1
GND
0.5
0
TEST CIRCUIT FOR PULSE RESPONSE 2
−0.5
0
1
2
3
4
5
6
7
8
t − Time − µs
Figure 16
18
50 Ω
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
PARAMETER MEASUREMENT INFORMATION†
STABILITY BOUNDARY CONDITION‡
80
VKA = 18 V
VKA = 3 V
VKA = 2 V
70
60
Unstable
VKA =VREF
IKA (mA)
50
Unstable
40
30
Unstable
20
Stable
10
Stable
0
0.00001
0.0001
0.01
0.001
CL (µF)
150 Ω
150 Ω
IK
IK
+
CL
−
R1 = 10 kΩ
CL
Vbat
R2
+
−
Vbat
TEST CIRCUIT FOR VKA = VREF
TEST CIRCUIT FOR VKA = 2 V, 3 V
† Operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied.
‡ The areas enclosed by the curves represent conditions that may cause the device to oscillate. For VKA = 2-V, 3-V, and 18-V curves, R2 and Vbat
were adjusted to establish the initial VKA and IK conditions with CL = 0. Vbat and CL then were adjusted to determine the ranges of stability.
Figure 17
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
19
SLVS555D – NOVEMBER 2004 – REVISED FEBRUARY 2005
APPLICATION INFORMATION
∼
VI
120 V
−
P
+
∼
VO
3.3 V
P
P
Gate Drive
VCC
Controller
VFB
TLVH431
Current
Sense
GND
P
P
P
P
Figure 18. Flyback With Isolation Using TLVH431 and TLVH432 as Voltage Reference and Error Amplifier
Figure 18 shows the TLVH431 used in a 3.3-V isolated flyback supply. Output voltage VO can be as low as
reference voltage VREF (1.24 V). The output of the regulator plus the forward voltage drop of the optocoupler
LED (1.24 + 1.4 = 2.64 V) determine the minimum voltage that can be regulated in an isolated supply
configuration. Regulated voltage as low as 2.7 Vdc is possible in the topology shown in Figure 18.
20
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLVH431ACDBVR
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TLVH431ACDBVT
PREVIEW
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TLVH431ACDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH431ACDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH431ACDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
TLVH431ACDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
TLVH431ACLP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
TLVH431ACLPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
Lead/Ball Finish
MSL Peak Temp (3)
TLVH431ACPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH431AIDBVR
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TLVH431AIDBVT
PREVIEW
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TLVH431AIDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH431AIDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH431AIDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
TLVH431AILP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
TLVH431AILPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
TLVH431AIPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH431AQDBVR
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TLVH431AQDBVT
PREVIEW
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TLVH431AQDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH431AQDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH431AQDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
TLVH431AQDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
TLVH431AQLP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
TLVH431AQLPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
TLVH431AQPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH431BCDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BCDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BCDBZR
ACTIVE
SOT-23
DBZ
3
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BCDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BCDCKR
ACTIVE
SC70
DCK
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BCDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BCLP
ACTIVE
TO-92
LP
3
1000
TBD
CU SNPB
Level-NC-NC-NC
TLVH431BCLPR
ACTIVE
TO-92
LP
3
2000
TBD
CU SNPB
Level-NC-NC-NC
TLVH431BIDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BIDBVT
ACTIVE
SOT-23
DBV
5
250
CU NIPDAU
Level-1-260C-UNLIM
Addendum-Page 1
Green (RoHS &
no Sb/Br)
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
TLVH431BIDBZR
PREVIEW
SOT-23
DBZ
3
TLVH431BIDBZT
ACTIVE
SOT-23
DBZ
3
250
TLVH431BIDCKR
ACTIVE
SC70
DCK
TLVH431BIDCKT
ACTIVE
SC70
TLVH431BILP
ACTIVE
TO-92
Lead/Ball Finish
MSL Peak Temp (3)
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
DCK
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
LP
3
1000
TBD
CU SNPB
Level-NC-NC-NC
TBD
CU SNPB
Level-NC-NC-NC
TLVH431BILPR
ACTIVE
TO-92
LP
3
2000
TLVH431BQDBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BQDBVT
ACTIVE
SOT-23
DBV
5
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BQDBZR
ACTIVE
SOT-23
DBZ
3
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BQDBZT
ACTIVE
SOT-23
DBZ
3
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BQDCKR
ACTIVE
SC70
DCK
6
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BQDCKT
ACTIVE
SC70
DCK
6
250
Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
TLVH431BQLP
ACTIVE
TO-92
LP
3
1000
TBD
CU SNPB
Level-NC-NC-NC
Level-NC-NC-NC
TLVH431BQLPR
ACTIVE
TO-92
LP
3
2000
TBD
CU SNPB
TLVH431CDBVR
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TLVH431CDBVT
PREVIEW
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TLVH431CDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH431CDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH431CDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
TLVH431CDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
TLVH431CLP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
TLVH431CLPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
TLVH431CPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH431IBQDBZR
PREVIEW
SOT-23
DBZ
3
TBD
Call TI
Call TI
TLVH431IDBVR
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TLVH431IDBVT
PREVIEW
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TLVH431IDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH431IDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH431IDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
TLVH431IDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
TLVH431ILP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
TLVH431ILPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
TLVH431IPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH431QDBVR
PREVIEW
SOT-23
DBV
5
3000
TBD
Call TI
Call TI
TLVH431QDBVT
PREVIEW
SOT-23
DBV
5
250
TBD
Call TI
Call TI
TLVH431QDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
Lead/Ball Finish
MSL Peak Temp (3)
TLVH431QDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH431QDCKR
PREVIEW
SC70
DCK
6
3000
TBD
Call TI
Call TI
TLVH431QDCKT
PREVIEW
SC70
DCK
6
250
TBD
Call TI
Call TI
TLVH431QLP
PREVIEW
TO-92
LP
3
1000
TBD
Call TI
Call TI
TLVH431QLPR
PREVIEW
TO-92
LP
3
2000
TBD
Call TI
Call TI
TLVH431QPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432ACDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432ACDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432ACPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432AIDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432AIDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432AIPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432AQDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432AQDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432AQPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432BCDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432BCDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432BCPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432BIDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432BIDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432BIPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432BQDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432BQDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432BQPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432CDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432CDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432CPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432IDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432IDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432IPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
TLVH432QDBZR
PREVIEW
SOT-23
DBZ
3
3000
TBD
Call TI
Call TI
TLVH432QDBZT
PREVIEW
SOT-23
DBZ
3
250
TBD
Call TI
Call TI
TLVH432QPK
PREVIEW
SOT-89
PK
3
1000
TBD
Call TI
Call TI
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 4
MECHANICAL DATA
MPDS108 – AUGUST 2001
DBZ (R-PDSO-G3)
PLASTIC SMALL-OUTLINE
3,04
2,80
2,05
1,78
0,60
0,45
1,03
0,89
1,40
1,20
2,64
2,10
0,51
0,37
1,12
0,89
0,100
0,013
0,55 REF
0,180
0,085
4203227/A 08/01
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Dimensions are inclusive of plating.
Dimensions are exclusive of mold flash and metal burr.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDS114 – FEBRUARY 2002
DCK (R-PDSO-G6)
PLASTIC SMALL-OUTLINE PACKAGE
0,30
0,15
0,65
6
0,10 M
4
1,40
1,10
1
0,13 NOM
2,40
1,80
3
Gage Plane
2,15
1,85
0,15
0°–8°
0,46
0,26
Seating Plane
1,10
0,80
0,10
0,00
0,10
4093553-3/D 01/02
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC MO-203
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MSOT002A – OCTOBER 1994 – REVISED NOVEMBER 2001
LP (O-PBCY-W3)
PLASTIC CYLINDRICAL PACKAGE
0.205 (5,21)
0.175 (4,44)
0.165 (4,19)
0.125 (3,17)
DIA
0.210 (5,34)
0.170 (4,32)
Seating
Plane
0.157 (4,00) MAX
0.050 (1,27)
C
0.500 (12,70) MIN
0.104 (2,65)
FORMED LEAD OPTION
0.022 (0,56)
0.016 (0,41)
0.016 (0,41)
0.014 (0,35)
STRAIGHT LEAD OPTION
D
0.135 (3,43) MIN
0.105 (2,67)
0.095 (2,41)
0.055 (1,40)
0.045 (1,14)
1
2
3
0.105 (2,67)
0.080 (2,03)
0.105 (2,67)
0.080 (2,03)
4040001-2 /C 10/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Lead dimensions are not controlled within this area
D. FAlls within JEDEC TO -226 Variation AA (TO-226 replaces TO-92)
E. Shipping Method:
Straight lead option available in bulk pack only.
Formed lead option available in tape & reel or ammo pack.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
MECHANICAL DATA
MSOT002A – OCTOBER 1994 – REVISED NOVEMBER 2001
LP (O-PBCY-W3)
PLASTIC CYLINDRICAL PACKAGE
0.539 (13,70)
0.460 (11,70)
1.260 (32,00)
0.905 (23,00)
0.650 (16,50)
0.610 (15,50)
0.020 (0,50) MIN
0.098 (2,50)
0.384 (9,75)
0.335 (8,50)
0.748 (19,00)
0.217 (5,50)
0.433 (11,00)
0.335 (8,50)
0.748 (19,00)
0.689 (17,50)
0.114 (2,90)
0.094 (2,40)
0.114 (2,90)
0.094 (2,40)
0.169 (4,30)
0.146 (3,70)
DIA
0.266 (6,75)
0.234 (5,95)
0.512 (13,00)
0.488 (12,40)
TAPE & REEL
4040001-3 /C 10/01
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Tape and Reel information for the Format Lead Option package.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated