TI SN74AVC2T45DCTR

SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
FEATURES
•
•
•
•
•
•
•
•
DCT OR DCU PACKAGE
(TOP VIEW)
Available in the Texas Instruments
NanoFree™ Package
Control Inputs VIH/VIL Levels Are Referenced
to VCCA Voltage
Fully Configurable Dual-Rail Design Allows
Each Port to Operate Over the Full 1.2-V to
3.6-V Power-Supply Range
I/Os Are 4.6-V Tolerant
Ioff Supports Partial-Power-Down Mode
Operation
Max Data Rates
– 500 Mbps (1.8-V to 3.3-V Translation)
– 320 Mbps (<1.8-V to 3.3-V Translation)
– 320 Mbps (Translate to 2.5 V or 1.8 V)
– 280 Mbps (Translate to 1.5 V)
– 240 Mbps (Translate to 1.2 V)
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
– 8000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
– 1000-V Charged-Device Model (C101)
VCCA
A1
A2
GND
1
8
2
7
3
6
4
5
VCCB
B1
B2
DIR
YZP PACKAGE
(BOTTOM VIEW)
GND
D1
4 5
D2
DIR
A2
C1
3 6
C2
B2
A1
B1
2 7
B2
B1
VCCA
A1
1 8
A2
VCCB
DESCRIPTION/ORDERING INFORMATION
This dual-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is
designed to track VCCA. VCCA accepts any supply voltage from 1.2 V to 3.6 V. The B port is designed to track
VCCB. VCCB accepts any supply voltage from 1.2 V to 3.6 V. This allows for universal low-voltage bidirectional
translation between any of the 1.2-V, 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.
ORDERING INFORMATION
PACKAGE (1) (2)
TA
–40°C to 85°C
(1)
(2)
(3)
ORDERABLE PART NUMBER
TOP-SIDE MARKING (3)
NanoFree™ – WCSP (DSBGA)
0.23-mm Large Bump – YZP (Pb-free)
Reel of 3000
SN74AVC2T45YZPR
_ _ _TD_
SSOP – DCT
Reel of 3000
SN74AVC2T45DCTR
DT2_ _ _
VSSOP – DCU
Reel of 3000
SN74AVC2T45DCUR
DT2_
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
DCT: The actual top-side marking has three additional characters that designate the year, month, and assembly/test site.
DCU: The actual top-side marking has one additional character that designates the assembly/test site.
YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following
character to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NanoFree is a trademark of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2003–2007, Texas Instruments Incorporated
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
DESCRIPTION/ORDERING INFORMATION (CONTINUED)
The SN74AVC2T45 is designed for asynchronous communication between two data buses. The logic levels of
the direction-control (DIR) input activate either the B-port outputs or the A-port outputs. The device transmits
data from the A bus to the B bus when the B-port outputs are activated and from the B bus to the A bus when
the A-port outputs are activated. The input circuitry on both A and B ports always is active and must have a logic
HIGH or LOW level applied to prevent excess ICC and ICCZ.
The SN74AVC2T45 is designed so that the DIR input is powered by VCCA.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
The VCC isolation feature ensures that if either VCC input is at GND, both ports are in the high-impedance state.
NanoFree™ package technology is a major breakthrough in IC packaging concepts, using the die as the
package.
FUNCTION TABLE (1)
(EACH TRANSCEIVER)
(1)
INPUT
DIR
OPERATION
L
B data to A bus
H
A data to B bus
Input circuits of the data I/Os always are active.
LOGIC DIAGRAM (POSITIVE LOGIC)(1)
DIR
A1
5
2
7
A2
3
6
VCCA
(1)
2
B1
Pin numbers are for the DCT and DCU packages only.
Submit Documentation Feedback
VCCB
B2
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Absolute Maximum Ratings
(1)
over operating free-air temperature range (unless otherwise noted)
VCCA
VCCB
Supply voltage range
VI
Input voltage range (2)
MIN
MAX
–0.5
4.6
I/O ports (A port)
–0.5
4.6
I/O ports (B port)
–0.5
4.6
Control inputs
–0.5
4.6
A port
–0.5
4.6
B port
–0.5
4.6
A port
–0.5
VCCA + 0.5
B port
–0.5
VCCB + 0.5
UNIT
V
V
VO
Voltage range applied to any output in the high-impedance or
power-off state (2)
VO
Voltage range applied to any output in the high or low state (2) (3)
IIK
Input clamp current
VI < 0
–50
mA
IOK
Output clamp current
VO < 0
–50
mA
IO
Continuous output current
±50
mA
±100
mA
Continuous current through VCCA, VCCB, or GND
θJA
Package thermal impedance (4)
Tstg
Storage temperature range
DCT package
220
DCU package
227
YZP package
(1)
(2)
(3)
(4)
V
V
°C/W
102
–65
150
°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current ratings are observed.
The package thermal impedance is calculated in accordance with JESD 51-7.
Submit Documentation Feedback
3
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Recommended Operating Conditions (1) (2) (3) (4) (5)
VCCI
VCCO
MIN
MAX
VCCA
Supply voltage
1.2
3.6
V
VCCB
Supply voltage
1.2
3.6
V
High-level
input voltage
VIH
Low-level
input voltage
VIL
High-level
input voltage
VIH
VIL
Low-level
input voltage
VI
Input voltage
Data inputs (4)
Data inputs
(4)
DIR
(referenced to VCCA) (5)
DIR
(referenced to VCCA) (5)
1.2 V to 1.95 V
VCCI × 0.65
1.95 V to 2.7 V
1.6
2.7 V to 3.6 V
2
VO
Output voltage
IOH
VCCI × 0.35
1.95 V to 2.7 V
0.7
2.7 V to 3.6 V
0.8
1.2 V to 1.95 V
VCCA × 0.65
1.95 V to 2.7 V
1.6
2.7 V to 3.6 V
2
1.2 V to 1.95 V
VCCA × 0.35
1.95 V to 2.7 V
0.7
3.6
0
VCCO
3-state
0
3.6
Δt/Δv
Input transition rise or fall rate
TA
Operating free-air temperature
(1)
(2)
(3)
(4)
(5)
V
0.8
Active state
Low-level output current
V
V
0
High-level output current
IOL
V
1.2 V to 1.95 V
2.7 V to 3.6 V
4
UNIT
1.2 V
–3
1.4 V to 1.6 V
–6
1.65 V to 1.95 V
–8
2.3 V to 2.7 V
–9
3 V to 3.6 V
–12
1.2 V
3
1.4 V to 1.6 V
6
1.65 V to 1.95 V
8
2.3 V to 2.7 V
9
3 V to 3.6 V
12
–40
V
V
mA
mA
5
ns/V
85
°C
VCCI is the VCC associated with the input port.
VCCO is the VCC associated with the output port.
All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
For VCCI values not specified in the data sheet, VIH min = VCCI × 0.7 V, VIL max = VCCI × 0.3 V.
For VCCI values not specified in the data sheet, VIH min = VCCA × 0.7 V, VIL max = VCCA × 0.3 V.
Submit Documentation Feedback
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Electrical Characteristics
(1) (2)
over recommended operating free-air temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOL
II
1.2 V to 3.6 V
1.2 V to 3.6 V
IOH = –3 mA
1.2 V
1.2 V
IOH = –6 mA
1.4 V
1.4 V
1.05
IOH = –8 mA
1.65 V
1.65 V
1.2
IOH = –9 mA
2.3 V
2.3 V
1.75
IOH = –12 mA
3V
3V
2.3
IOL = 100 μA
1.2 V to 3.6 V
1.2 V to 3.6 V
IOL = 3 mA
1.2 V
1.2 V
IOL = 6 mA
1.4 V
1.4 V
0.35
1.65 V
1.65 V
0.45
IOL = 9 mA
2.3 V
2.3 V
0.55
IOL = 12 mA
3V
3V
1.2 V to 3.6 V
1.2 V to 3.6 V
Ioff
IOZ
IOL = 8 mA
DIR
A port
B port
VI = VIH
VI = VIL
VI = VCCA or GND
VI or VO = 0 to 3.6 V
B port
VO = VCCO or GND
A port
VI = VCCI or GND
ICCA
VI = VCCI or GND, IO = 0
ICCB
VI = VCCI or GND, IO = 0
ICCA + ICCB
(see Table 1)
–40°C to 85°C
VCCB
IOH = –100 μA
VOH
TA = 25°C
VCCA
VI = VCCI or GND, IO = 0
MIN
TYP
MAX
MIN MAX
UNIT
VCCO – 0.2
V
0.95
V
0.2
0.25
V
0.7
±0.025
±0.25
±1
0V
0 to 3.6 V
±0.1
±1
±5
0 to 3.6 V
0V
±0.1
±1
±5
0V
3.6 V
±0.5
±2.5
±5
3.6 V
0V
±0.5
±2.5
±5
1.2 V to 3.6 V
1.2 V to 3.6 V
10
0V
3.6 V
–2
3.6 V
0V
10
1.2 V to 3.6 V
1.2 V to 3.6 V
10
0V
3.6 V
10
3.6 V
0V
–2
1.2 V to 3.6 V
1.2 V to 3.6 V
20
μA
μA
μA
μA
μA
μA
CI
Control
inputs
VI = 3.3 V or GND
3.3 V
3.3 V
2.5
pF
Cio
A or B
port
VO = 3.3 V or GND
3.3 V
3.3 V
6
pF
(1)
(2)
VCCO is the VCC associated with the output port.
VCCI is the VCC associated with the input port.
Submit Documentation Feedback
5
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 1.2 V (see Figure 1)
PARAMETER
tPLH
tPHL
tPLH
tPHL
tPHZ
tPLZ
tPHZ
tPLZ
tPZH (1)
tPZL (1)
tPZH (1)
tPZL
(1)
(1)
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
DIR
A
DIR
B
DIR
A
DIR
B
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.8 V
VCCB = 2.5 V
VCCB = 3.3 V
TYP
TYP
TYP
TYP
TYP
3.1
2.6
2.4
2.2
2.2
3.1
2.6
2.4
2.2
2.2
3.4
3.1
3
2.9
2.9
3.4
3.1
3
2.9
2.9
5.2
5.2
5.1
5
4.8
5.2
5.2
5.1
5
4.8
5
4
3.8
2.8
3.2
5
4
3.8
2.8
3.2
8.4
7.1
6.8
5.7
6.1
8.4
7.1
6.8
5.7
6.1
8.3
7.8
7.5
7.2
7
8.3
7.8
7.5
7.2
7
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
UNIT
ns
ns
ns
ns
ns
ns
The enable time is a calculated value, derived using the formula shown in the enable times section.
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 1.5 V ± 0.1 V (see Figure 1)
PARAMETER
tPLH
tPHL
tPLH
tPHL
tPHZ
tPLZ
tPHZ
tPLZ
tPZH (1)
tPZL (1)
tPZH (1)
tPZL
(1)
6
(1)
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
DIR
A
DIR
B
DIR
A
DIR
B
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
2.8
0.7
5.4
0.5
4.6
0.4
3.7
0.3
3.5
2.8
0.7
5.4
0.5
4.6
0.4
3.7
0.3
3.5
2.7
0.8
5.4
0.7
5.2
0.6
4.9
0.5
4.7
2.7
0.8
5.4
0.7
5.2
0.6
4.9
0.5
4.7
3.9
1.3
8.5
1.3
7.8
1.1
7.7
1.4
7.6
3.9
1.3
8.5
1.3
7.8
1.1
7.7
1.4
7.6
4.7
1.1
7
1.4
6.9
1.2
6.9
1.7
7.1
4.7
1.1
7
1.4
6.9
1.2
6.9
1.7
7.1
7.4
12.4
12.1
11.8
11.8
7.4
12.4
12.1
11.8
11.8
6.7
13.9
12.4
11.4
11.1
6.7
13.9
12.4
11.4
11.1
The enable time is a calculated value, derived using the formula shown in the enable times section.
Submit Documentation Feedback
UNIT
ns
ns
ns
ns
ns
ns
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (see Figure 1)
PARAMETER
tPLH
tPHL
tPLH
tPHL
tPHZ
tPLZ
tPHZ
tPLZ
tPZH (1)
tPZL (1)
tPZH (1)
tPZL (1)
(1)
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
DIR
A
DIR
B
DIR
A
DIR
B
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
2.7
0.5
5.2
0.4
4.3
0.2
3.4
0.2
3.1
2.7
0.5
5.2
0.4
4.3
0.2
3.4
0.2
3.1
2.4
0.7
4.7
0.5
4.4
0.5
4
0.4
3.8
2.4
0.7
4.7
0.5
4.4
0.5
4
0.4
3.8
3.7
1.3
8.1
0.7
6.9
1.4
5.3
1.1
5.2
3.7
1.3
8.1
0.7
6.9
1.4
5.3
1.1
5.2
4.4
1.3
5.8
1.3
5.9
0.8
5.7
1.5
5.9
4.4
1.3
5.8
1.3
5.9
0.8
5.7
1.5
5.9
6.8
10.5
10.3
9.7
9.7
6.8
10.5
10.3
9.7
9.7
6.4
13.3
11.2
8.7
8.3
6.4
13.3
11.2
8.7
8.3
UNIT
ns
ns
ns
ns
ns
ns
The enable time is a calculated value, derived using the formula shown in the enable times section.
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (see Figure 1)
PARAMETER
tPLH
tPHL
tPLH
tPHL
tPHZ
tPLZ
tPHZ
tPLZ
tPZH (1)
tPZL (1)
tPZH (1)
tPZL
(1)
(1)
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
DIR
A
DIR
B
DIR
A
DIR
B
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
2.6
0.4
4.9
0.2
4
0.2
3
0.2
2.6
2.6
0.4
4.9
0.2
4
0.2
3
0.2
2.6
2.1
0.6
3.8
0.5
3.4
0.4
3
0.3
2.8
2.1
0.6
3.8
0.5
3.4
0.4
3
0.3
2.8
2.4
0.7
7.9
0.8
6.4
0.8
5
0.5
4.3
2.4
0.7
7.9
0.8
6.4
0.8
5
0.5
4.3
3.8
1
4.3
0.6
4.3
0.5
4.2
1.1
4.1
3.8
1
4.3
0.6
4.3
0.5
4.2
1.1
4.1
5.9
8.5
7.7
7.2
6.9
5.9
8.5
7.7
7.2
6.9
5
12.8
10.4
8
6.9
5
12.8
10.4
8
6.9
UNIT
ns
ns
ns
ns
ns
ns
The enable time is a calculated value, derived using the formula shown in the enable times section.
Submit Documentation Feedback
7
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Switching Characteristics
over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (see Figure 1)
PARAMETER
FROM
(INPUT)
TO
(OUTPUT)
A
B
B
A
DIR
A
DIR
B
DIR
A
DIR
B
tPLH
tPHL
tPLH
tPHL
tPHZ
tPLZ
tPHZ
tPLZ
tPZH (1)
tPZL (1)
tPZH (1)
tPZL (1)
(1)
VCCB = 1.2 V
VCCB = 1.5 V
± 0.1 V
VCCB = 1.8 V
± 0.15 V
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
TYP
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
2.5
0.3
4.7
0.2
3.8
0.2
2.8
0.2
2.4
2.5
0.3
4.7
0.2
3.8
0.2
2.8
0.2
2.4
2.1
0.6
3.6
0.4
3.1
0.3
2.6
0.3
2.4
2.1
0.6
3.6
0.4
3.1
0.3
2.6
0.3
2.4
2.9
1.1
8
1
6.5
1.3
4.7
1.2
4
2.9
1.1
8
1
6.5
1.3
4.7
1.2
4
3.4
0.5
6.6
0.3
5.6
0.3
4.6
1.1
4.2
3.4
0.5
6.6
0.3
5.6
0.3
4.6
1.1
4.2
5.5
10.2
8.7
7.2
6.6
5.5
10.2
8.7
7.2
6.6
5.4
12.7
10.3
7.5
6.4
5.4
12.7
10.3
7.5
6.4
UNIT
ns
ns
ns
ns
ns
ns
The enable time is a calculated value, derived using the formula shown in the enable times section.
Operating Characteristics
TA = 25°C
PARAMETER
CpdA (1)
CpdB (1)
(1)
8
A-port input,
B-port output
B-port input,
A-port output
A-port input,
B-port output
B-port input,
A-port output
TEST
CONDITIONS
CL = 0,
f = 10 MHz,
tr = tf = 1 ns
CL = 0,
f = 10 MHz,
tr = tf = 1 ns
VCCA =
VCCB = 1.2 V
VCCA =
VCCB = 1.5 V
VCCA =
VCCB = 1.8 V
VCCA =
VCCB = 2.5 V
VCCA =
VCCB = 3.3 V
TYP
TYP
TYP
TYP
TYP
3
3
3
3
4
12
13
13
14
15
12
13
13
14
15
3
3
3
3
4
UNIT
pF
pF
Power-dissipation capacitance per transceiver
Submit Documentation Feedback
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
Power-Up Considerations
A proper power-up sequence always should be followed to avoid excessive supply current, bus contention,
oscillations, or other anomalies. To guard against such power-up problems, take the following precautions:
1. Connect ground before any supply voltage is applied.
2. Power up VCCA.
3. VCCB can be ramped up along with or after VCCA.
Table 1. Typical Total Static Power Consumption (ICCA + ICCB)
VCCB
VCCA
0V
1.2 V
1.5 V
1.8 V
2.5 V
3.3 V
0V
0
<0.5
<0.5
<0.5
<0.5
<0.5
1.2 V
<0.5
<1
<1
<1
<1
1
1.5 V
<0.5
<1
<1
<1
<1
1
1.8 V
<0.5
<1
<1
<1
<1
<1
2.5 V
<0.5
1
<1
<1
<1
<1
3.3 V
<0.5
1
<1
<1
<1
<1
Submit Documentation Feedback
UNIT
μA
9
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
TYPICAL CHARACTERISTICS
6
6
5
5
4
4
tPHL - ns
tPLH - ns
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE,
TA = 25°C, VCCA = 1.2 V
3
2
3
2
VCCB = 1.2 V
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.5 V
VCCB = 1.8 V
1
VCCB = 1.8 V
1
VCCB = 2.5 V
VCCB = 2.5 V
VCCB = 3.3 V
VCCB = 3.3 V
0
0
10
20
30
40
50
0
60
0
10
20
CL - pF
30
CL - pF
40
50
60
6
6
5
5
4
4
tPHL - ns
tPLH - ns
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE,
TA = 25°C, VCCA = 1.5 V
3
2
3
2
VCCB = 1.2 V
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.5 V
VCCB = 1.8 V
1
VCCB = 1.8 V
1
VCCB = 2.5 V
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
VCCB = 3.3 V
60
0
0
CL - pF
10
Submit Documentation Feedback
10
20
30
CL - pF
40
50
60
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
TYPICAL CHARACTERISTICS
6
6
5
5
4
4
tPHL - ns
tPLH - ns
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE,
TA = 25°C, VCCA = 1.8 V
3
2
3
2
VCCB = 1.2 V
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.5 V
VCCB = 1.8 V
1
VCCB = 1.8 V
1
VCCB = 2.5 V
VCCB = 2.5 V
VCCB = 3.3 V
0
0
10
20
30
40
50
VCCB = 3.3 V
0
60
0
10
20
CL - pF
30
CL - pF
40
50
60
50
60
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE,
TA = 25°C, VCCA = 2.5 V
6
6
VCCB = 1.2 V
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.5 V
VCCB = 1.8 V
5
VCCB = 1.8 V
5
VCCB = 2.5 V
VCCB = 2.5 V
VCCB = 3.3 V
VCCB = 3.3 V
4
tPHL - ns
tPLH - ns
4
3
3
2
2
1
1
0
0
10
20
30
40
50
60
0
0
CL - pF
Submit Documentation Feedback
10
20
30
CL - pF
40
11
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
TYPICAL CHARACTERISTICS
TYPICAL PROPAGATION DELAY (A to B) vs LOAD CAPACITANCE,
TA = 25°C, VCCA = 3.3 V
6
6
VCCB = 1.2 V
VCCB = 1.2 V
VCCB = 1.5 V
VCCB = 1.5 V
VCCB = 1.8 V
5
VCCB = 1.8 V
5
VCCB = 2.5 V
VCCB = 2.5 V
VCCB = 3.3 V
VCCB = 3.3 V
4
tPHL - ns
tPLH - ns
4
3
3
2
2
1
1
0
0
10
20
30
40
50
60
0
0
CL - pF
12
Submit Documentation Feedback
10
20
30
CL - pF
40
50
60
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
PARAMETER MEASUREMENT INFORMATION
2 × VCCO
S1
RL
From Output
Under Test
Open
GND
CL
(see Note A)
TEST
S1
tpd
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCCO
GND
RL
tw
LOAD CIRCUIT
VCCI
VCCI/2
Input
VCCO
CL
RL
VTP
1.2 V
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
15 pF
15 pF
15 pF
15 pF
15 pF
2 kΩ
2 kΩ
2 kΩ
2 kΩ
2 kΩ
0.1 V
0.1 V
0.15 V
0.15 V
0.3 V
VCCI/2
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VCCA
Output
Control
(low-level
enabling)
VCCA/2
VCCA/2
0V
tPZL
VCCI
Input
VCCI/2
VCCI/2
0V
tPLH
Output
tPHL
VOH
VCCO/2
VOL
VCCO/2
tPLZ
VCCO
Output
Waveform 1
S1 at 2 × VCCO
(see Note B)
VCCO/2
VOL + VTP
VOL
tPZH
Output
Waveform 2
S1 at GND
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
tPHZ
VCCO/2
VOH - VTP
VOH
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, ZO = 50 Ω, dv/dt ≥ 1 V/ns.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. VCCI is the VCC associated with the input port.
I. VCCO is the VCC associated with the output port.
Figure 1. Load Circuit and Voltage Waveforms
Submit Documentation Feedback
13
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
APPLICATION INFORMATION
Figure 2 is an example circuit of the SN74AVC2T45 used in a unidirectional logic level-shifting application.
VCC1
VCC2
VCC1
VCC2
1
8
2
7
3
6
4
5
VCC2
VCC1
SYSTEM-1
SYSTEM-2
PIN
NAME
FUNCTION
1
VCCA
VCC1
SYSTEM-1 supply voltage (1.2 V to 3.6 V)
DESCRIPTION
2
A1
OUT1
Output level depends on VCC1 voltage.
3
A2
OUT2
Output level depends on VCC1 voltage.
4
GND
GND
Device GND
5
DIR
DIR
The GND (low-level) determines B-port to A-port direction.
6
B2
IN2
Input threshold value depends on VCC2 voltage.
7
B1
IN1
Input threshold value depends on VCC2 voltage.
8
VCCB
VCC2
SYSTEM-2 supply voltage (1.2 V to 3.6 V)
Figure 2. Unidirectional Logic Level-Shifting Application
14
Submit Documentation Feedback
SN74AVC2T45
DUAL-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES531J – DECEMBER 2003 – REVISED JUNE 2007
APPLICATION INFORMATION
Figure 3 shows the SN74AVC2T45 used in a bidirectional logic level-shifting application. Since the
SN74AVC2T45 does not have an output-enable (OE) pin, the system designer should take precautions to avoid
bus contention between SYSTEM-1 and SYSTEM-2 when changing directions.
VCC1
VCC1
I/O-1
VCC2
VCC2
Pullup/Pulldown
or Bus Hold(1)
Pullup/Pulldown
or Bus Hold(1)
1
8
2
7
3
6
4
5
I/O-2
DIR CTRL
SYSTEM-1
SYSTEM-2
Following is a sequence that illustrates data transmission from SYSTEM-1 to SYSTEM-2 and then from
SYSTEM-2 to SYSTEM-1.
(1)
STATE
DIR CTRL
I/O-1
I/O-2
1
H
Out
In
DESCRIPTION
2
H
Hi-Z
Hi-Z
SYSTEM-2 is getting ready to send data to SYSTEM-1. I/O-1 and I/O-2 are
disabled.
The bus-line state depends on pullup or pulldown. (1)
3
L
Hi-Z
Hi-Z
DIR bit is flipped. I/O-1 and I/O-2 still are disabled.
The bus-line state depends on pullup or pulldown. (1)
4
L
In
Out
SYSTEM-2 data to SYSTEM-1
SYSTEM-1 data to SYSTEM-2
SYSTEM-1 and SYSTEM-2 must use the same conditions, i.e., both pullup or both pulldown.
Figure 3. Bidirectional Logic Level-Shifting Application
Enable Times
Calculate the enable times for the SN74AVC2T45 using the following formulas:
• tPZH (DIR to A) = tPLZ (DIR to B) + tPLH (B to A)
• tPZL (DIR to A) = tPHZ (DIR to B) + tPHL (B to A)
• tPZH (DIR to B) = tPLZ (DIR to A) + tPLH (A to B)
• tPZL (DIR to B) = tPHZ (DIR to A) + tPHL (A to B)
In a bidirectional application, these enable times provide the maximum delay from the time the DIR bit is
switched until an output is expected. For example, if the SN74AVC2T45 initially is transmitting from A to B, then
the DIR bit is switched; the B port of the device must be disabled before presenting it with an input. After the B
port has been disabled, an input signal applied to it appears on the corresponding A port after the specified
propagation delay.
Submit Documentation Feedback
15
PACKAGE OPTION ADDENDUM
www.ti.com
11-Jun-2010
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package
Drawing
Pins
Package Qty
Eco Plan
(2)
Lead/
Ball Finish
MSL Peak Temp
(3)
Samples
(Requires Login)
SN74AVC2T45DCTR
ACTIVE
SM8
DCT
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
SN74AVC2T45DCTRE4
ACTIVE
SM8
DCT
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
SN74AVC2T45DCTRG4
ACTIVE
SM8
DCT
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
SN74AVC2T45DCTT
ACTIVE
SM8
DCT
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Purchase Samples
SN74AVC2T45DCTTE4
ACTIVE
SM8
DCT
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Purchase Samples
SN74AVC2T45DCTTG4
ACTIVE
SM8
DCT
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Purchase Samples
SN74AVC2T45DCUR
ACTIVE
US8
DCU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
SN74AVC2T45DCURE4
ACTIVE
US8
DCU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
SN74AVC2T45DCURG4
ACTIVE
US8
DCU
8
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
SN74AVC2T45DCUT
ACTIVE
US8
DCU
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Purchase Samples
SN74AVC2T45DCUTE4
ACTIVE
US8
DCU
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Purchase Samples
SN74AVC2T45DCUTG4
ACTIVE
US8
DCU
8
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Purchase Samples
SN74AVC2T45YZPR
ACTIVE
DSBGA
YZP
8
3000
Green (RoHS
& no Sb/Br)
(1)
SNAGCU
Level-1-260C-UNLIM
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
Addendum-Page 1
Request Free Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Jun-2010
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jan-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
SN74AVC2T45DCUR
US8
DCU
8
3000
180.0
9.2
2.25
3.35
1.05
4.0
8.0
Q3
SN74AVC2T45YZPR
DSBGA
YZP
8
3000
180.0
8.4
1.02
2.02
0.63
4.0
8.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jan-2010
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
SN74AVC2T45DCUR
US8
DCU
8
3000
202.0
201.0
28.0
SN74AVC2T45YZPR
DSBGA
YZP
8
3000
220.0
220.0
34.0
Pack Materials-Page 2
MECHANICAL DATA
MPDS049B – MAY 1999 – REVISED OCTOBER 2002
DCT (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,30
0,15
0,65
8
0,13 M
5
0,15 NOM
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
ÇÇÇÇÇ
2,90
2,70
4,25
3,75
Gage Plane
PIN 1
INDEX AREA
1
0,25
4
0° – 8°
3,15
2,75
0,60
0,20
1,30 MAX
Seating Plane
0,10
0,10
0,00
NOTES: A.
B.
C.
D.
4188781/C 09/02
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion
Falls within JEDEC MO-187 variation DA.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated