ALLEGRO UDN2987

2987
8-CHANNEL
SOURCE DRIVER
Data Sheet
29310.4A
2987
8-CHANNEL SOURCE DRIVER
WITH OVER-CURRENT PROTECTION
IN 1
1
20
OUT 1
IN 2
2
19
OUT 2
IN 3
3
18
OUT 3
IN 4
4
17
OUT 4
IN 5
5
16
OUT 5
IN 6
6
15
OUT 6
IN 7
7
14
OUT 7
IN 8
8
13
OUT 8
12
GROUND
11
V
S
FAULT
x8
9
OE
OE/R
10
OEN
FF
SENSEN
Providing over-current protection for each of its eight sourcing
outputs, the UDN2987A and UDN2987LW drivers are used as an
interface between standard low-level logic and relays, motors, solenoids, LEDs, and incandescent lamps. The device includes thermal
shutdown and output transient protection/clamp diodes for use with
sustaining voltages to 35 V.
In these drivers, each channel includes a latch to turn OFF that
channel if the maximum channel current is exceeded. All channels are
disabled if the thermal shutdown is activated. A common FAULT
output is used to indicate either chip thermal shutdown or any overcurrent condition. All outputs are enabled by pulling the common OE/
R input high. When OE/R is low, all outputs are inhibited and the eight
latches are reset.
Under normal operating conditions, each of eight outputs will
source in excess of 100 mA continuously at an ambient temperature of
25°C and a supply of 35 V. The over-current fault circuit will protect
the device from short-circuits to ground with supply voltages of up to
35 V.
Dwg. PP-067
Note that the UDN2987A (DIP) and the UDN2987LW
(SOIC) are electrically identical and share a common
terminal number assignment.
The inputs are compatible with 5 V and 12 V logic systems—TTL,
Schottky TTL, DTL, PMOS, and CMOS. In all cases, the output is
switched ON by an active high input level. The UDN2987A is supplied
in a 20-pin dual in-line plastic package; the UDN2987LW is supplied in
a 20-lead small-outline plastic package.
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Driver Supply Voltage, VS ..................... 35 V
Output Sustaining Voltage, VCE(sus) ...... 35 V
Continuous Output Current,
IOUT ........................................ -500 mA*
FAULT Output Voltage, VCE ................. 35 V
FAULT Output Current, lC ................. 30 mA
Input Voltage, VIN ................................. 15 V
Package Power Dissipation,
PD ........................................ See Graph
FEATURES
■
■
■
■
■
■
■
350 mA Output Source Current
Over-Current Protected
Internal Ground Clamp Diodes
Output Breakdown Voltage 35 V, Minimum
TTL, DTL, PMOS, or CMOS Compatible Inputs
Internal Thermal Shutdown
Automotive Capable
Operating Temperature Range,
TA ................................. -20°C to +85°C
Storage Temperature Range,
TS ............................... -55°C to +150°C
* Outputs are disabled at approximately -500 mA
per driver.
Always order by complete part number:
Part Number
Package
UDN2987A
20-Pin DIP
UDN2987LW
20-Lead Wide-Body SOIC
2987
8-CHANNEL
SOURCE DRIVER
ALLOWABLE PACKAGE POWER DISSIPATION IN WATTS
FUNCTIONAL BLOCK DIAGRAM
2.5
2.0
SU
FF
IX
1.5
SU
FF
IX
'A
', R
θJ
A
'LW
', R
θJ
1.0
A =
=
55
°C
/W
70
°C
/W
0.5
0
25
50
75
100
125
AMBIENT TEMPERATURE IN °C
150
Dwg. GS-004A
Dwg. No. A-13,286
OVER-CURRENT FAULT SENSE
OUTPUT CURRENT WAVESHAPES
PHL
Dwg. No. A-13,293
Dwg. No. A-13,292
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright © 1987, 1997, Allegro MicroSystems, Inc.
2987
8-CHANNEL
SOURCE DRIVER
ELECTRICAL CHARACTERISTICS at TA = 25°C, VOE = 2.4 V, VS = 35 V
(unless otherwise noted).
Characteristic
Symbol
Functional Supply Range
VS
Output Leakage Current
ICEX
Test Conditions
Min.
Limits
Typ.
Max.
Units
7.0
—
35
V
VIN = 0.4 V*
—
<-5.0
-200
µA
Output Sustaining Voltage
VOUT(sus)
IOUT = -350 mA, L = 2.0 mH
35
—
—
V
Output Saturation Voltage
VOUT(SAT)
VIN = 2.4 V, IOUT = -100 mA
—
1.6
1.8
V
VIN = 2.4 V, IOUT = -225 mA
—
1.7
1.9
V
VIN = 2.4 V, IOUT = -350 mA
—
1.8
2.0
V
Channel Shutdown Threshold
FAULT Leakage Current
FAULT Saturation Voltage
Input Voltage
Input Current
IM
VIN = 2.4 V
-370
-500
—
mA
ICEX
VCC = 35 V
—
<1.0
100
µA
VCE(SAT)
IC = 30 mA
—
0.3
0.8
V
VIN(ON)
2.4
—
—
V
V IN(OFF)
—
—
0.4
V
VIN = 2.4 V
—
125
170
µA
VIN = 5.0 V
—
840
1020
µA
VIN = 12 V
—
1500
1800
µA
VIN = 0.4 V
—
—
15
µA
IIN(ON)
IIN(OFF)
Clamp Diode Leakage Current
IR
VR = 35 V, TA = 70°C
—
—
50
µA
Clamp Diode Forward Voltage
VF
IF = 350 mA
—
1.5
1.8
V
IS(ON)
VIN = 2.4 V*, Outputs Open
—
13
18
mA
IS(OFF)
VIN = 0.4 V*
—
8.0
12
mA
Supply Current
Thermal Shutdown
TJ
—
165
—
°C
Thermal Hysteresis
∆TJ
—
15
—
°C
Propagation Delay Time
tPLH
RL = 100Ω
—
0.3
0.6
µs
tPHL
RL = 100Ω
—
2.0
4.0
µs
—
1.0
—
µs
Dead Time
*AII inputs simultaneously.
td
2987
8-CHANNEL
SOURCE DRIVER
ALLOWABLE OUTPUT CURRENT
AS A FUNCTION OF DUTY CYCLE
(UDN2987A shown, multiply by 78% for UDN2987LW)
At +25°C
APPLICATIONS INFORMATION
AND CIRCUIT DESCRIPTION
As with all power integrated circuits, the UDN2987A
and UDN2987LW have a maximum allowable output
current rating. The 500 mA rating does not imply that
operation at that value is permitted or even obtainable.
The channel output current trip point is specified as -370
mA, minimum; therefore, attempted operation at current
levels greater than -370 mA may cause a fault indication
and channel shutdown. The device is tested at a maximum of -350 mA and that is the recommended maximum
output current per driver. It provides protection for current
overloads or shorted loads up to 35 V.
All outputs are enabled by pulling the OE/R input high.
When OE/R is low or allowed to float (internal pull-down),
all outputs are inhibited and the latches are reset. Note
that the RESET pulse duration (OE/R low) should be
at least 1 µs. This will ensure safe operation under
attempted RESET conditions with a shorted load. The
latches are also reset during power up, regardless of the
state of the OE/R input.
At +50°C
The load current causes a small voltage drop across
the internal low-value sense resistor. This voltage is
compared to the voltage drop across a reference resistor
with a constant current. The two resistors are matched to
eliminate errors due to manufacturing tolerances or
temperature effects. Each channel includes a comparator
and its own latch. An over-current fault (VSENSE > VREF)
will set the affected latch and shut down only that channel.
All other channels will continue to operate normally. The
latch includes a 1 µs delay (td) to prevent unwanted
triggering due to crossover currents generated when
switching inductive loads. For an abrupt short circuit, the
delay and output switching times will allow a brief,
permissable current in excess of the trip current before the
output driver is turned OFF.
A common thermal shutdown disables all outputs
if the chip temperature exceeds +165°C. At thermal
shutdown, all latches are reset. The outputs are disabled
until the chip cools down to about +150°C (thermal
hysteresis).
A common open-collector FAULT output is used to
indicate any channel over-current condition or chip
thermal shutdown.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
2987
8-CHANNEL
SOURCE DRIVER
UDN2987A
Dimensions in Inches
(controlling dimensions)
20
0.014
0.008
11
0.430
MAX
0.280
0.240
0.300
BSC
1
0.070
0.045
0.100
1.060
0.980
10
BSC
0.005
MIN
0.210
MAX
0.015
0.150
0.115
MIN
0.022
0.014
Dwg. MA-001-20 in
Dimensions in Millimeters
(for reference only)
20
0.355
0.204
11
10.92
MAX
7.11
6.10
7.62
BSC
1
1.77
1.15
2.54
26.92
24.89
BSC
10
0.13
MIN
5.33
MAX
0.39
3.81
2.93
MIN
0.558
0.356
NOTES: 1. Exact body and lead configuration at vendor’s option within limits shown.
2. Lead spacing tolerance is non-cumulative.
3. Lead thickness is measured at seating plane or below.
Dwg. MA-001-20 mm
2987
8-CHANNEL
SOURCE DRIVER
UDN2987LW
Dimensions in Inches
(for reference only)
20
11
0.0125
0.0091
0.419
0.394
0.2992
0.2914
0.050
0.016
0.020
0.013
1
2
0.050
3
0° TO 8°
BSC
0.5118
0.4961
0.0926
0.1043
0.0040 MIN.
Dwg. MA-008-20 in
Dimensions in Millimeters
(controlling dimensions)
20
11
0.32
0.23
10.65
10.00
7.60
7.40
1.27
0.40
0.51
0.33
1
2
1.27
3
13.00
12.60
BSC
0° TO 8°
2.65
2.35
NOTES: 1.
2.
0.10 MIN.
Exact body and lead configuration at vendor’s option within limits shown.
Lead spacing tolerance is non-cumulative.
Dwg. MA-008-20 mm
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
2987
8-CHANNEL
SOURCE DRIVER
This page intentionally left blank
2987
8-CHANNEL
SOURCE DRIVER
POWER SOURCE DRIVERS
SELECTION GUIDE
IN ORDER OF 1) OUTPUT CURRENT, 2) OUTPUT VOLTAGE, 3) NUMBER OF DRIVERS
Features
Output Ratings *
mA
-25
-120
-350
*
†
V
60
60
60
60
60
85
-25
30
50
35
50
50
-50
80
80
-80
#
8
10
12
20
32
8
8
8
8
8
8
8
8
8
8
8
Serial
Input
–
X
X
X
X
–
–
–
X
–
–
X
–
–
X
–
Latched
Drivers
Diode
Clamp
Saturated
Outputs
Internal
Protection
X
X
X
X
X
–
–
–
X
–
–
X
–
–
X
–
–
–
–
–
–
–
–
X
X
X
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
X
–
–
–
–
–
–
Active Pull-Down
Active Pull-Down
Active Pull-Down
Active Pull-Down
–
X
X
X
X
X
X
X
X
X
X
†
Part Number
5815
5810-F and 6809/10
5811 and 6811
5812-F and 6812
5818-F and 6818
6118
2585
2985
5895
2987
2981 and 2982
5891
2580
2983 and 2984
5890
2588
Current is maximum specified test condition, voltage is maximum rating. See specification for sustaining voltage limits or
over-current protection voltage limits.
Complete part number includes additional characters to indicate operating temperature range and package style.
Allegro MicroSystems, Inc. reserves the right to make, from time to time, such departures from the
detail specifications as may be required to permit improvements in the design of its products.
The information included herein is believed to be accurate and reliable. However, Allegro
MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other
rights of third parties which may result from its use.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000