ALLEGRO UGS3133LT

Data Sheet
27631.2B
3132 AND
3133
ULTRA-SENSITIVE BIPOLAR
HALL-EFFECT SWITCHES
X
These Hall-effect switches are designed for magnetic actuation using
a bipolar magnetic field, i.e., a north-south alternating field. They
combine extreme magnetic sensitivity with excellent stability over
varying temperature and supply voltage. The high sensitivity permits
their use with multi-pole ring magnets over relatively large distances.
2
3
OUTPUT
1
GROUND
CC
SUPPLY
V
Each device includes a voltage regulator, quadratic Hall voltage
generator, temperature stability circuit, signal amplifier, Schmitt trigger,
and open-collector output on a single silicon chip. The on-board regulator permits operation with supply voltages of 4.5 to 24 V. The switch
output can sink up to 25 mA. With suitable output pull up, they can be
used directly with bipolar or MOS logic circuits.
Dwg. PH-003A
Pinning is shown viewed from branded side.
The three package styles available provide a magnetically optimized
package for most applications. Suffix ‘LT’ is a miniature SOT-89/TO243AA transistor package for surface-mount applications; suffixes ‘U’,
and ‘UA’ feature wire leads for through-hole mounting. Prefix ‘UGN’
devices are rated for continuous operation over the temperature range of
-20°C to +85°C, prefix ‘UGS’ devices over an extended range of -40°C
to +125°C, and prefix ‘UGL’ devices over the range of -40°C to +150°C.
FEATURES
■ 4.5 V to 24 V Operation
■ Reverse Battery Protection
■ Superior Temperature Stability
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC . . . . . . . . . . . . . 25 V
Reverse Battery Voltage, VRCC . . . . -35 V
Magnetic Flux Density, B . . . . Unlimited
Output OFF Voltage, VOUT . . . . . . . . 25 V
Continuous Output Current, IOUT . 25 mA
Operating Temperature Range, TA
Prefix UGL . . . . . . . -40°C to +150°C
Prefix UGN . . . . . . . . -20°C to +85°C
Prefix UGS . . . . . . . -40°C to +125°C
Storage Temperature Range,
TS . . . . . . . . . . . . . . . -65°C to +150°C
■ Superior Supply Voltage Stability
■ Activate with Multi-Pole Ring Magnets
■ Solid-State Reliability
■ Small Size
■ Constant Output Amplitude
■ Resistant to Physical Stress
Always order by complete part number
including prefix and suffix, e.g., UGN3132LT .
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
FUNCTIONAL BLOCK DIAGRAM
1
VCC
REG.
X
3
OUTPUT
2
GROUND
Dwg. FH-005-2
ELECTRICAL CHARACTERISTICS at TA = +25°C
Limits
Characteristic
Symbol
Supply Voltage
VCC
Min.
Typ.
Max.
Units
Operating
4.5
—
24
V
VOUT(SAT)
IOUT = 20 mA, B ≥ BOP
—
145
400
mV
Output Leakage Current
IOFF
VOUT = 24 V, B ≤ BRP
—
<1.0
10
µA
Supply Current
ICC
VCC = 24 V, B ≤ BRP
—
4.3
9.0
mA
Output Saturation Voltage
Test Conditions
Output Rise Time
tr
VCC = 12 V, RL = 820 Ω, CL = 20 pF
—
0.04
2.0
µs
Output Fall Time
tf
VCC = 12 V, RL = 820 Ω, CL = 20 pF
—
0.18
2.0
µs
MAGNETIC CHARACTERISTICS over operating temperature and voltage range.
Limits
Characteristic
Symbol
Operate Point
BOP
Release Point
Hysteresis
BRP
Bhys
Device Type*
Min.
Typ.
Max.
Units
3132
—
32
95
G
3133
—
32
75
G
3132
-95
-20
—
G
3133
-75
-20
—
G
Both
30
52
—
G
NOTE: As used here, negative flux densities are defined as less than zero (algebraic convention.)
Typical values are at TA = +25°C and VCC = 12 V.
*
Complete part number includes a prefix denoting operating temperature range (UGL, UGN, or UGS)
and a suffix denoting package type (LT, U, or UA).
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Copyright © 1996,1999, Allegro MicroSystems, Inc.
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
TYPICAL CHARACTERISTICS
40
40
OPERATE POINT
OPERATE POINT
20
SWITCH POINT IN GAUSS
SWITCH POINT IN GAUSS
20
VCC = 12 V
0
I OUT = 20 mA
RELEASE POINT
-20
T A = 25°C
0
I OUT = 20 mA
-20
RELEASE POINT
-40
-50
-25
0
25
50
75
AMBIENT TEMPERATURE IN °C
-40
4.0
125
100
8.0
12
16
SUPPLY VOLTAGE IN VOLTS
Dwg. GH-022
Dwg. GH-021
6.0
200
I OUT = 20 mA
VCC = 12 V
SUPPLY CURRENT IN mA
SATURATION VOLTAGE IN mV
B ≥ B OP
175
150
5.0
4.0
B ≤ B RP
125
100
-50
28
24
20
-25
0
25
50
75
100
125
-25
0
25
50
75
AMBIENT TEMPERATURE IN °C
AMBIENT TEMPERATURE IN °C
Dwg. GH-024
www.allegromicro.com
3.0
-50
100
125
Dwg. GH-023
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
SENSOR LOCATIONS
(±0.005” [0.13mm] die placement)
SUFFIX “LT”
ACTIVE AREA DEPTH
0.030"
0.76 mm
NOM
0.089"
2.26 mm
0.043"
1.09 mm
A
1
2
3
Dwg. MH-008-2C
SUFFIX “U”
ACTIVE AREA DEPTH
0.016"
0.41 mm
NOM
SUFFIX “UA”
ACTIVE AREA DEPTH
0.019"
0.48 mm
NOM
0.091"
2.31 mm
0.082"
2.07 mm
0.070"
1.78 mm
A
BRANDED
SURFACE
0.055"
1.39 mm
A
BRANDED
SURFACE
1
2
1
2
3
3
Dwg. MH-011-10
Dwg. MH-002-2B
Allegro
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
PACKAGE DESIGNATOR ‘LT’
(SOT-89/TO-243AA)
Dimensions in Inches
(for reference only)
0.181
0.173
0.072
0.064
0.167
0.155
1
2
0.063
0.055
3
0.102
0.090
0.0173
0.0138
0.090
0.084
0.0189
0.0142
0.0221
0.0173
0.047
0.035
0.059
BSC
0.118
BSC
Dwg. MA-009-3A in
Dimensions in Millimeters
(controlling dimensions)
4.60
4.40
1.83
1.62
4.25
3.94
1
2
3
2.60
2.29
0.44
0.35
2.29
2.13
0.48
0.36
1.20
0.89
0.56
0.44
1.50
BSC
1.60
1.40
3.00
BSC
Dwg. MA-009-3A mm
NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are
measured at the widest point (parting line).
2. Exact body and lead configuration at vendor’s option within limits shown.
3. Height does not include mold gate flash.
www.allegromicro.com
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
PACKAGE DESIGNATOR ‘U’
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
0.183
0.178
4.65
4.52
0.063
0.059
1.60
1.50
0.181
0.176
4.60
4.47
45°
0.086
1
2
45°
0.018
3
2.18
1
2
0.46
3
MAX
MAX
0.44
0.35
15.24
14.23
0.0173
0.0138
0.600
0.560
0.48
0.36
0.0189
0.0142
SEE NOTE
SEE NOTE
1.27
2.54
0.050
0.100
Dwg. MH-003E in
Devices in the ‘U’ package are
NOT RECOMMENDED FOR NEW DESIGN
NOTES: 1. Tolerances on package height and width represent allowable mold offsets. Dimensions given are measured at the widest
point (parting line).
2. Exact body and lead configuration at vendor’s option within limits shown.
3. Height does not include mold gate flash.
4. Recommended minimum PWB hole diameter to clear transition area is 0.035" (0.89 mm).
5. Where no tolerance is specified, dimension is nominal.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Dwg. MH-003E mm
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
PACKAGE DESIGNATOR ‘UA’
Dimensions in Millimeters
(for reference only)
Dimensions in Inches
(controlling dimensions)
0.164
0.159
4.17
4.04
0.062
0.058
45°
1.57
1.47
45°
0.122
0.117
3.10
2.97
45°
0.085
1
2
3
45°
0.031
2.16
MAX
1
2
3
0.79
MAX
0.640
0.600
16.26
15.24
0.0173
0.0138
0.0189
0.0142
SEE NOTE
0.48
0.36
SEE NOTE
0.050
BSC
0.44
0.35
1.27
Dwg. MH-014E in
NOTES: 1. Tolerances on package height and width represent
allowable mold offsets. Dimensions given are measured at the
widest point (parting line).
2. Exact body and lead configuration at vendor’s option
within limits shown.
3. Height does not include mold gate flash.
4. Recommended minimum PWB hole diameter to clear
transition area is 0.035" (0.89 mm).
5. Where no tolerance is specified, dimension is nominal.
BSC
Dwg. MH-014E mm
The products described herein are manufactured under one or
more of the following U.S. patents: 5,045,920; 5,264,783; 5,442,283;
5,389,889; 5,581,179; 5,517,112; 5,619,137; 5,621,319; 5,650,719;
5,686,894; 5,694,038; 5,729,130; 5,917,320; and other patents
pending.
Allegro MicroSystems, Inc. reserves the right to make, from time to
time, such departures from the detail specifications as may be
required to permit improvements in the performance, reliability, or
manufacturability of its products. Before placing an order, the user is
cautioned to verify that the information being relied upon is current.
Allegro products are not authorized for use as critical components
in life-support appliances, devices, or systems without express written
approval.
The information included herein is believed to be accurate and
reliable. However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor for any infringements of patents or other rights of
third parties that may result from its use.
www.allegromicro.com
3132 AND 3133
BIPOLAR
HALL-EFFECT SWITCHES
HALL-EFFECT SENSORS SELECTION GUIDE
Partial Part
Number
Avail. Oper.
Characteristics at TA = +25°C
Temp.
BOP(max) BRP(min) Bhys(typ)
Features
HALL-EFFECT UNIPOLAR SWITCHES in order of BOP and Bhys
3240
3210
3361
3362
3161
3141
3235
E/L
E
E
E
E
E/L
S
5140
3142
3143
3144
3122
3123
3121
3150
E
E/L
E/L
E/L
E/L
E/L
E/L
J
+50
±70
+120
+120
+160
+160
+175
-25
+200
+230
+340
+350
+400
+440
+450
+40 to +850
+5.0
±5.0
+50
+50
+30
+10
+25
-175
+50
+75
+165
+50
+140
+180
+125
–
10
7.7
5.0*
5.0*
20
55
15*
15*
55
55
55
55
105
105
105
20
Notes
chopper stabilized
micropower, chopper stabilized
2-wire, chopper stabilized
2-wire, chopper stabilized
2-wire
1
output 1
output 2
300 mA output
2
2
1, 3
programmable, chopper stabilized
1
†
HALL-EFFECT LATCHES & BIPOLAR SWITCHES in order of BOP and Bhys
3260
E/L
+30
-30
20
bipolar, chopper stabilized
3280
E/L
+40
-40
45
chopper stabilized
3134
E/L
+50
-50
27
bipolar switch
3133
K/L/S
+75
-75
52
bipolar switch
3281
E/L
+90
-90
100
chopper stabilized
3132
K/L/S
+95
-95
52
bipolar switch
3187
E/L
+150
-150
100*
3177
S
+150
-150
200
3625
S
+150
-150
200
900 mA outputs
1, 3, 5
3626
S
+150
-150
200
400 mA outputs
1, 3, 5
3195
E/L
+160
-160
220
1, 4
3197
L
+160
-160
230
1
3175
S
+170
-170
200
3188
E/L
+180
-180
200*
3283
E/L
+180
-180
300
chopper stabilized
3189
E/L
+230
-230
100*
3275
S
+250
-250
100*
5
3185
E/L
+270
-270
340*
Operating Temperature Ranges:
S = -20°C to +85°C, E = -40°C to +85°C, J = -40°C to +115°C, K = -40°C to +125°C, L = -40°C to +150°C
Notes 1. Protected.
2. Output 1 switches on south pole, output 2 switches on north pole for 2-phase, bifilar-wound, unipolar-driven brushless dc
motor control.
3. Power driver output.
4. Active pull down.
5. Complementary outputs for 2-phase bifilar-wound, unipolar-driven brushless dc motor control.
* Minimum.
† Latches will not switch on removal of magnetic field; bipolar switches may switch on removal of field but require field reversal
for reliable operation over operating temperature range.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000