AWT6134 KPCS/CDMA 3.4V/28dBm Linear Power Amplifier Module PRELIMINARY DATA SHEET - Rev 1.0 FEATURES • InGaP HBT Technology • High Efficiency: 39% • Low Quiescent Current: 48 mA • Low Leakage Current in Shutdown Mode: <1 µA • VREF = +2.8 V (+2.7 V min over temp) • Optimized for a 50 Ω System • Low Profile Miniature Surface Mount Package: 1.56mm Max • CDMA 1XRTT Compliant • CDMA 1xEV-DO Compliant APPLICATIONS • M7 Package 10 Pin 4mm x 4mm Surface Mount Module Korean PCS CDMA Wireless Handsets PRODUCT DESCRIPTION The AWT6134 meets the increasing demands for higher efficiency and linearity in CDMA 1XRTT handsets. The PA module is optimized for VREF = +2.8 V, a requirement for compatibility with the Qualcomm 6000 chipset. The device is manufactured on an advanced InGaP HBT MMIC technology offering state-of-the-art reliability, temperature stability, and ruggedness. Selectable bias modes that optimize efficiency for different output power levels, and a shutdown mode with low leakage current, increase handset talk and standby time. The self-contained 4mm x 4mm surface mount package incorporates matching networks optimized for output power, efficiency, and linearity in a 50 Ω system. GND at slug (pad) VCC 1 10 VCC RFIN 2 9 GND GND 3 8 RFOUT 7 GND 6 GND VMODE 4 Bias Control VREF 5 Figure 1: Block Diagram 07/2003 AWT6134 GND VCC 1 10 VCC RFIN 2 9 GND GND 3 8 RFOUT VMODE 4 7 GND VREF 5 6 GND GND Figure 2: Pinout (X-ray Top View) Table 1: Pin Description 2 PIN NAME DESCRIPTION 1 V CC Supply Voltage 2 RFIN RF Input 3 GND Ground 4 VMODE Mode Control Voltage 5 VREF Reference Voltage 6 GND Ground 7 GND Ground 8 RFOUT RF Output 9 GND Ground 10 V CC Supply Voltage PRELIMINARY DATA SHEET - Rev 1.0 07/2003 AWT6134 ELECTRICAL CHARACTERISTICS Table 2: Absolute Minimum and Maximum Ratings PARAMETER MIN MAX UNIT Supply Voltage (VCC) 0 +5 V Mode Control Voltage (VMODE) 0 +3.5 V Reference Voltage (VREF) 0 +3.5 V RF Input Power (PIN) - +10 dB m -40 +150 °C Storage Temperature (TSTG) Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Table 3: Operating Ranges PARAMETER MIN TYP MAX UNIT COMMENTS Operating Frequency (f) 1750 - 1780 MHz Supply Voltage (VCC) +3.2 +3.4 +4.2 V Reference Voltage (VREF) +2.7 0 +2.8 - +3.1 +0.5 V PA "on" PA "shut down" Mode Control Voltage (VMODE) +2.5 0 +2.8 - +3.1 +0.5 V Low Bias Mode High Bias Mode RF Output Power (POUT) +27.5(1) +28.0 - dB m Case Temperature (TC) -30 - +85 °C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Notes: (1) For operation at TC = +85 °C and VCC = +3.2 V, POUT is derated by 0.5 dB. PRELIMINARY DATA SHEET - Rev 1.0 07/2003 3 AWT6134 Table 4: Electrical Specifications (TC = +25 °C, VCC = +3.4 V, VREF = +2.8 V, 50 Ω system) MIN TYP MAX UNIT 24 21 26 23.5 29 27 dB POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.8 V Adjacent Channel Power (1) at ±1.25 kHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -49 -52 -46.5 -46.5 dB c POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.8 V Adjacent Channel Power (1) at ±2.25 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -60 -68 -57 -57 dB c POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.8 V 37 8 39 9 - % POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.8 V Quiescent Current (Icq) - 48 60 mA VMODE = +2.8 V Reference Current - 3.5 5 mA through VREF pin, PA "on" Mode Control Current - 0.3 0.5 mA through VMODE pin, VMODE = +2.8 V Leakage Current - <1 5 µA VCC = +4.2 V, VREF = 0 V VMODE = 0 V Noise in Receive Band 1840 MHz to 1870 MHz - -137 -141 -135 -138 dBm/Hz Harmonics 2fo 3fo, 4fo - -45 -55 -30 -30 dB c Input Impedance - - 2:1 VSWR PARAMETER Gain Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure - - -65 dB c 8:1 - - VSWR Notes: (1) ACPR and PAE limits apply to middle frequency only. 4 PRELIMINARY DATA SHEET - Rev 1.0 07/2003 COMMENTS POUT = +28 dBm, VMODE = 0 V POUT = +16 dBm, VMODE = +2.8 V POUT < +28 dBm POUT < +28 dBm In-band load VSWR < 8:1 Out-of-band load VSWR < 8:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range AWT6134 Table 5: Electrical Specifications (TC = +25 °C, VCC = +3.4 V, VREF = +2.9 V, VMODE = +2.9 V, 50 Ω system) PARAMETER MIN TYP MAX UNIT Gain 23.5 20 25 23.5 28 27 dB POUT = +28 dBm POUT = +16 dBm Adjacent Channel Power (1) at ±1.25 kHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -50 -52 -46.5 -46.5 dB c POUT = +28 dBm POUT = +16 dBm Adjacent Channel Power (1) at ±2.25 MHz offset Primary Channel BW = 1.23 MHz Adjacent Channel BW = 30 kHz - -58 -68 -56 -57 dB c POUT = +28 dBm POUT = +16 dBm 37 8 40 9 - % POUT = +28 dBm POUT = +16 dBm Quiescent Current (Icq) - 56 68 mA VREF = +2.9 V Reference Current - 3.5 5 mA through VREF pin, PA "on" Mode Control Current - 0.3 0.5 mA through VMODE pin Leakage Current - <1 5 µA VCC = +4.2 V, VREF = 0 V VMODE = 0 V Noise in Receive Band 1840 MHz to 1870 MHz - -135 -133 Harmonics 2fo 3fo, 4fo - -45 -55 -30 -30 dB c Input Impedance - - 2:1 VSWR Power-Added Efficiency (1) Spurious Output Level (all spurious outputs) Load mismatch stress with no permanent degradation or failure COMMENTS dBm/Hz POUT = +28 dBm, VMODE = +2.8 V - - -65 dB c 8:1 - - VSWR POUT < +28 dBm In-band load VSWR < 8:1 Out-of-band load VSWR < 8:1 Applies over all voltage and temperature operating ranges VCC = +5.0 V, PIN = +5 dBm Applies over full operating temperature range Notes: (1) ACPR and PAE limits apply to middle frequency only. PRELIMINARY DATA SHEET - Rev 1.0 07/2003 5 AWT6134 APPLICATION INFORMATION To ensure proper performance, refer to all related Application Notes on the ANADIGICS web site: http://www.anadigics.com Shutdown Mode The power amplifier may be placed in a shutdown mode by applying logic low levels (see Operating Ranges table) to both the VREF and VMODE voltages. Bias Modes The power amplifier may be placed in either a Low Bias mode or a High Bias mode by applying the appropriate logic level (see Operating Ranges table) to the VMODE voltage. The Bias Control table lists the recommended modes of operation for various applications. Table 6: Bias Control APPLICATION POUT LE V E LS BIAS MODE V R EF VMODE CDMA - low power <+16dBm Low +2.8 V +2.8 V CDMA - high power >+16 dBm High +2.8 V 0V - Shutdown 0V 0V Shutdown VCC1 VCC2 C1 0.01µF C3 0.01µF RF IN VMODE VREF C2 0.01µF 1 VCC 2 VCC 10 3 RFIN GND 9 GND RFOUT 8 4 VMODE GND 7 5 VREF GND 6 GND at slug Figure 3: Application Circuit Schematic 6 PRELIMINARY DATA SHEET - Rev 1.0 07/2003 C4 2.2µF ceramic RF OUT AWT6134 PACKAGE OUTLINE Figure 4: M7 Package Outline - 10 Pin 4mm x 4mm Surface Mount Module AWT6134 AWT6134 BBB LASER MARKED Figure 5: Branding Specification PRELIMINARY DATA SHEET - Rev 1.0 07/2003 7 AWT6134 COMPONENT PACKAGING Figure 6: Tape & Reel Packaging Table 7: Tape & Reel Dimensions 8 PACKAGE TYPE TAPE WIDTH POCKET PITCH REEL CAPACITY MAX REEL DIA 4mm X 4mm 12mm 8mm 2500 13" PRELIMINARY DATA SHEET - Rev 1.0 07/2003 AWT6134 NOTES PRELIMINARY DATA SHEET - Rev 1.0 07/2003 9 AWT6134 NOTES 10 PRELIMINARY DATA SHEET - Rev 1.0 07/2003 AWT6134 NOTES PRELIMINARY DATA SHEET - Rev 1.0 07/2003 11 AWT6134 ORDERING INFORMATION ORDER NUMBER TEMPERATURE RANGE PACKAGE DESCRIPTION AWT6134M7P8 -30 oC to +110 oC 10 Pin 4mm x 4mm Surface Mount Module COMPONENT PACKAGING Tape and Reel, 2500 pieces per Reel ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: [email protected] IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product’s formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 PRELIMINARY DATA SHEET - Rev 1.0 07/2003