AAT3532 MicroPower™ Microprocessor Reset Circuit General Description Features The AAT3532 PowerManager™ product is a member of AATI’s Total Power Management ICs™ (TPMIC™) product family. It is a fully integrated device for monitoring microprocessor activity, external reset, and power supply conditions. The device holds the microprocessor in a reset condition for a minimum of 250ms while VCC is established to ensure correct system start-up. A manual reset can be initiated via a de-bounced input pin. As an additional level of protection, the AAT3532 includes a watchdog timer which requires a periodic strobe input from the microprocessor to ensure correct operation. The AAT3532 has a programmable watchdog timer and voltage tolerance level. The quiescent supply current is extremely low, typically 23µA. • • • • • • Adjustable 4.5V or 4.75V Voltage Monitor 250ms (min) Reset Pulse Width Low quiescent current: typically 23µA Adjustable Watchdog Timer (150ms, 600ms, or 1200ms) De-bounced Manual Reset Input Operates down to 20ns strobe input pulse width No external components Temp range -40° to 85°C Standard 8 pin SOP package Pin compatible with MAX1232 Preliminary Information • • • • PowerManager™ Applications The AAT3532 is available in an 8-pin SOP package specified over -40° to 85°C temperature range. • • • • • • Computers Controllers Telecom Equipment Embedded Systems Intelligent Instrumentation Automotive Typical Application VDD VDD VCC PBRST RST AAT3532 RESET INPUT µP RST TD ST I/O TOL GND 3532.2001.11.0.9 1 AAT3532 MicroPower™ Microprocessor Reset Circuit Pin Descriptions Pin # Symbol 1 PBRST 2 3 4 5 TD TOL GND RST 6 7 RST ST 8 Vcc Function Pushbutton reset input. A de-bounced active low input for manual reset. Guaranteed to recognize inputs 20ms or greater. Watchdog time delay set input. See Table 1 for watchdog timeout selections. Tolerance set. Input selects 5% or 10% threshold detection IC ground connection Reset Output (active high). Activated when either: VCC falls below the reset voltage threshold, or PBRST is forced low, or ST not strobed within the minimum timeout period, or during power-up. Reset Output (active low, open drain). Inverse of RST. Strobe input to watchdog timer. A pulse is required within watchdog timeout period to prevent RST and RST entering active state 5V Supply Pin Programming Selections Time-Out TD Pin GND Float VCC Min Typ Max 62.5ms 250ms 500ms 150ms 600ms 1200ms 250ms 1000ms 2000ms Table 1: TD Pin Programming for Watchdog Timeout Selections TOL Pin Tolerance VCC GND 10% 5% Table 2: Reset Voltage Threshold Programming Selections Pin Configuration SOP-8 (Top View) 2 PBRST TD 1 8 Vcc 2 7 TOL 3 6 ST RST GND 4 5 RST 3532.2001.11.0.9 AAT3532 MicroPower™ Microprocessor Reset Circuit Absolute Maximum Ratings Symbol (TA=25°C unless otherwise noted) Description Value Units -0.5 to 6 V -0.5 to (VCC+0.5) V VCC VCC to GND VI/O Voltage on I/O pins relative to GND TA Operating Temperature Range -40 to 85 °C TS Storage Temperature Range -65 to 150 °C TLEAD Maximum Soldering Temperature (at Leads) for 10s 300 °C VESD ESD Rating1—HBM 2000 V Note: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at conditions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time. Note 1: Human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin. Thermal Characteristics Symbol ΘJA PD Description Maximum Thermal Resistance2 2 Maximum Power Dissipation Value Units 100 °C/W 1.25 W Note 2: Mounted on an FR4 board. 3532.2001.11.0.9 3 AAT3532 MicroPower™ Microprocessor Reset Circuit DC Electrical Characteristics (VIN = 4.5V to 5.5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C) Symbol Description VCC Supply Voltage IQ VCCTP IIL IOH IOL VIH VIL IRST Conditions Quiescent Current1 VCC = 5.5V Reset Threshold 5% Reset Threshold 10% Input Leakage ST, TOL Output Current RST2 Current RST2, RST ST and PBRST Input High ST and PBRST Input Low RST Output Leakage TOL = GND TOL = VCC Min Typ Max Units 4.5 5.0 23 160 4.62 4.37 5.5 50 500 4.74 4.49 1.0 V CMOS Levels TTL Levels 4.50 4.25 -1.0 -8.0 10.0 2.0 -0.3 VOH = 2.4V VOL = 0.4V VCC+0.3 0.8 1.0 VOH = VCC AC Electrical Characteristics µA V V µA mA mA V V µA (VIN = 4.5V to 5.5V, TA = -40 to 85°C unless otherwise noted. Typical values are at TA=25°C) Symbol CIN COUT tPB tPBD tRST tST tTD tf tr tRPD tRPU Description Conditions 3 Input Capacitance ST, TOL Output Capacitance RST, RST3 PBRST4 PBRST Delay Reset Active Time ST Pulse Width ST Time-out Period VCC VCC VCC VCC Fall Time3 Rise Time3 Detect to RST High and RST Low Detect to RST Low and RST Open TA = 25ºC TA = 25ºC Fig 2 Fig 2 Fig 3 TD Pin = 0V TD Pin = Open TD Pin = VCC 4.75V to 4.25V 4.25V to 4.75V VCC Falling VCC Rising Min 20 1 250 20 62.5 250 500 10 0 250 Typ Max Units 5 7 pF pF ms ms ms ns ms ms ms µs µs µs ms 4 610 20 1000 150 600 1200 250 1000 2000 5 610 50 1000 Notes: 1. Measured with outputs open and ST toggling at 100kHz, 50% duty cycle 2. RST is an open drain output 3. Guaranteed by design and not subject to production testing. 4. PBRST must remain low for greater than 20ms to guarantee a reset 4 3532.2001.11.0.9 AAT3532 MicroPower™ Microprocessor Reset Circuit Functional Block Diagram VCC VCC Tolerance Select TOL Reset Generator RST RST VREF De-Bounce Circuit PBRST Watchdog Timer Detector ST Watchdog Timer TD GND age can be set by programming the TOL pin. Connecting TOL to VCC sets the 10% tolerance of the VCC supply (typically 4.37V for VCC = 5V). Connecting TOL to GND sets the 5% tolerance of the VCC supply (typically 4.62V for VCC = 5V). The reset pin is guaranteed to remain asserted for a minimum period of 250ms after VCC has risen above the reset threshold voltage. Applications Information Power Monitor The reset function monitors the VCC supply to ensure a microprocessor is correctly reset and is powered up into a known condition following a power supply failure. RST and RST will remain valid for Vcc voltages down to 1.4V. RST output is an open drain output. For correct operation, a pull-up resistor of 10kΩ should be connected between this output and VCC. The RST and RST pins are asserted whenever VCC drops below the reset threshold voltage. This volt- +5V +4.75V (5% Trip Point) VCC +4.50V (10% Trip Point) 0V RESET output delay (VCC Falling) RESET output delay (VCC Rising) tRPU tRPD RST RST Figure 1. Reset Output Delay 3532.2001.11.0.9 5 AAT3532 MicroPower™ Microprocessor Reset Circuit Applications Information Manual Reset The PBRST pin makes it possible to manually reset the system by either directly connecting a mechanical push-button between the PBRST pin and GND or connecting to a logic low output. Internal de-bounce circuitry is provided to reduce the effect of noise glitches at the input. The signal should remain low for a minimum of 20ms for correct operation. Once the PBRST signal is released (or goes to a logic high), RESET (RESET) remains asserted for a minimum of 250ms. tPB tPBD PBRST tRST RESET RESET Figure 2 Push-button Reset Watchdog Timer The watchdog timer monitors the microprocessor to ensure that the system is functioning correctly. The ST pin of the AAT3532 can be derived from the microprocessor data signals, address signals, and/or I/O signals. The watchdog timer function forces the RST and RST signals into the active state when the ST input is not toggled by a predetermined time. This time period is set by the logic state of the TD pin as shown in Table 1. The timer starts once the RST signals become inactive. If the watchdog timer does not receive a high-to-low transition within the specified timeout period, then the RST signals are activated for a minimum 250ms. In normal operation the timer should receive a transition from the microprocessor within the timeout period, in which case the timer is reset and normal operation continues. The AAT3532 will accept and recognize ST pulses down to a minimum of 20ns wide. tST ST tTD Figure 3. Watchdog Input 6 3532.2001.11.0.9 AAT3532 MicroPower™ Microprocessor Reset Circuit Ordering Information Package Part Number Marking 8 Pin SOIC Bulk Tape and Reel AAT3532IAS-B1 AAT3532IAS-T1 Package Information SOP-8 Dim E H D 7 (4x) A c A2 b y 3532.2001.11.0.9 e A1 Θ L A A1 A2 B C D E e H L Y θ1 Millimeters Min Max 1.35 1.75 0.10 0.25 1.45 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 5.80 6.20 0.40 1.27 0.00 0.10 0° 8° Inches Min Max 0.053 0.069 0.004 0.010 0.057 0.013 0.020 0.007 0.010 0.189 0.197 0.150 0.157 0.050 0.228 0.244 0.016 0.050 0.000 0.004 0° 8° Note: 1. PACKAGE BODY SIZES EXCLUDE MOLD FLASH PROTRUSIONS OR GATE BURRS. 2. TOLERANCE± 0.1000mm (4mil) UNLESS OTHERWISE SPECIFIED 3. COPLANARITY: 0.1000mm 4. DIMENSION L IS MEASURED IN GAGE PLANE. 5. CONTROLLING DIMENSION IS MILLIMETER, CONVERTED INCH DIMENSIONS ARE NOT NECESSARILY EXACT. 7 AAT3532 MicroPower™ Microprocessor Reset Circuit This page intentionally left blank. Advanced Analogic Technologies, Inc. 1250 Oakmead Parkway, Suite 310, Sunnyvale, CA 94086 Phone (408) 524-9684 Fax (408) 524-9689 8 3532.2001.11.0.9