I N D U C T O R S May 2013 Inductors for Standard Circuits Wound Ferrite NL series NL453232 NL565050 4532 [1812 inch]* 5650 [2220 inch] * Dimensions Code JIS[EIA] (1/12) I N D U C T O R S REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 6 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150°C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130516 / e511_nl.fm (2/12) I N D U C T O R S Product compatible with RoHS directive Compatible with lead-free solders Inductors for Standard Circuits Wound Ferrite Overview of the NL Series FEATURES Resin mold type wound inductor for standard circuits. 1 to 10000µH, E-12 Series, wide lineup compatible with J (±5%) tolerance, can be used for applications that need to meet strict L tolerance such as filter circuits. Has excellent inductance temperature characteristics in the operating temperature range. APPLICATION Smart meters, AV equipment, xDSL, electronic devices for communications infrastructure such as mobile base stations, industrial equipment, other PART NUMBER CONSTRUCTION NL Series name 453232 L×W×H Dimensions (mm) 453232 4.5×3.2×3.2 565050 5.6×5.0×5.0 T Packaging style T Taping - 1R0 J Inductance (µH) 1R0 1 100 10 101 100 102 1000 103 10000 Inductance tolerance J ±5% - PF Internal code OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Package quantity Operating Storage Type temperature temperature (pieces/reel) （°C） （°C） NL453232 –40 to +105 –40 to +105 500 NL565050 –40 to +105 –40 to +105 400 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. Individual weight （mg） 180 380 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (3/12) I N D U C T O R S Overview of the NL Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150°C 180°C Time t1 90 to 120s Soldering Temp. Time T3 t2 230°C 40s Peak Temp. T4 255°C Time t3 10s max. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (4/12) I N D U C T O R S NL series NL453232 Type SHAPE & DIMENSIONS 4.5±0.3 102J 2.6±0.1 3.2±0.2 R0.2 C0.5 (0.6) (3.3) (0.6) 3.2±0.2 0.5 Dimensions in mm 2.8 RECOMMENDED LAND PATTERN 1.5 3 1.5 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (5/12) I N D U C T O R S NL series NL453232 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (µH) Tolerance Q min. 1 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 50 40 40 40 40 40 40 40 40 40 30 30 30 30 L, Q measuring frequency (MHz) 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 Self-resonant frequency (MHz) min. 100 80 70 60 55 50 45 40 35 33 27 25 20 18 17 15 13 12 11 10 10 9 9 8 8 6 5 5 4 4 3.5 3 3 3 3 2.5 2.5 DC resistance (Ω ) max. Rated current (mA) max. Part No. 0.5 0.55 0.6 0.65 0.7 0.75 0.8 0.9 1 1.1 1.2 1.4 1.6 2 2.5 2.8 3.2 3.6 4 4.5 5 5.5 6 7 8 8 9 9.5 10 12 14 16 26 30 30 35 40 450 430 410 390 380 370 355 330 315 300 285 270 250 225 200 190 180 170 160 150 140 135 130 120 110 110 105 102 100 92 85 80 62 50 50 30 30 NL453232T-1R0J-PF NL453232T-1R2J-PF NL453232T-1R5J-PF NL453232T-1R8J-PF NL453232T-2R2J-PF NL453232T-2R7J-PF NL453232T-3R3J-PF NL453232T-3R9J-PF NL453232T-4R7J-PF NL453232T-5R6J-PF NL453232T-6R8J-PF NL453232T-8R2J-PF NL453232T-100J-PF NL453232T-120J-PF NL453232T-150J-PF NL453232T-180J-PF NL453232T-220J-PF NL453232T-270J-PF NL453232T-330J-PF NL453232T-390J-PF NL453232T-470J-PF NL453232T-560J-PF NL453232T-680J-PF NL453232T-820J-PF NL453232T-101J-PF NL453232T-121J-PF NL453232T-151J-PF NL453232T-181J-PF NL453232T-221J-PF NL453232T-271J-PF NL453232T-331J-PF NL453232T-391J-PF NL453232T-471J-PF NL453232T-561J-PF NL453232T-681J-PF NL453232T-821J-PF NL453232T-102J-PF Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (10% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 20°C by self heating) ○ Measurement equipment Measurement item Product No. L, Q 4194A Self-resonant frequency 8753C DC resistance VP-2941A ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Panasonic • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (6/12) I N D U C T O R S NL series NL453232 Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100000 102J 10000 821J 681J 561J 471J 391J 121J 331J 271J 221J 181J 820J 680J 151J 101J 1000 470J 8R2J Inductance(µH) 390J 330J 270J 220J 180J 150J 120J 100 100J 560J 6R8J 5R6J 4R7J 3R9J 3R3J 10 2R7J 2R2J 1R8J 1R5J 1R2J 1R0J 1 0.1 0.001 0.01 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (7/12) I N D U C T O R S NL series NL453232 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 100 90 1R5J 1R0J 2R2J 80 4R7J 1R2J 5R6J 2R7J 470J 70 560J 6R8J 3R3J 120J 60 8R2J 680J Q 331J 50 100J 150J 271J 40 471J 221J 820J 220J 101J 330J 30 391J 270J 20 681J 390J 121J 3R9J 821J 1R8J 10 181J 151J 0 0.001 180J 102J 561J 0.01 0.1 1 10 100 Frequency(MHz) ○ Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (8/12) I N D U C T O R S NL series NL565050 Type SHAPE & DIMENSIONS 5±0.3 4±0.2 5.6±0.3 472J C1 (0.5) (4.6) (0.5) 5±0.3 1 Dimensions in mm 4.5 RECOMMENDED LAND PATTERN 2 4 2 Dimensions in mm • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (9/12) I N D U C T O R S NL series NL565050 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE L (mH) tolerance Q min. 1.2 1.5 1.8 2.2 2.7 3.3 3.9 4.7 5.6 6.8 8.2 10 ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% ±5% 30 30 30 30 30 30 30 30 30 30 30 20 L, Q measuring frequency (MHz) 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.0796 Self-resonant frequency (MHz) min. 1.5 1.4 1.3 1.2 1.1 1 1 0.9 0.8 0.7 0.6 0.5 DC resistance (Ω ) max. Rated current (mA) max. Part No. 17 20 30 35 55 60 70 78 85 110 125 150 75 70 60 55 45 40 38 36 33 30 28 25 NL565050T-122J-PF NL565050T-152J-PF NL565050T-182J-PF NL565050T-222J-PF NL565050T-272J-PF NL565050T-332J-PF NL565050T-392J-PF NL565050T-472J-PF NL565050T-562J-PF NL565050T-682J-PF NL565050T-822J-PF NL565050T-103J-PF Rated current: smaller value of either Idc1 or Idc2. Idc1: When based on the inductance change rate (10% below the initial value) Idc2: When based on the temperature increase (Temperature increase of 20°C by self heating) ○ Measurement equipment Measurement item Product No. L, Q 4194A Self-resonant frequency 8753C DC resistance VP-2941A ＊ Equivalent measurement equipment may be used. Manufacturer Agilent Technologies Agilent Technologies Panasonic • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (10/12) I N D U C T O R S NL series NL565050Type ELECTRICAL CHARACTERISTICS L FREQUENCY CHARACTERISTICS GRAPH 100000 103J 100000 822J 392J 682J 562J 472J 332J 272J 222J 182J 152J Inductance(µH) 10000 122J 1000 100 10 1 0.001 0.01 0.1 Frequency(MHz) 1 10 ○ Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (11/12) I N D U C T O R S NL series NL565050 Type ELECTRICAL CHARACTERISTICS Q FREQUENCY CHARACTERISTICS GRAPH 60 50 40 332J 562J 472J Q 182J 30 222J 822J 272J 20 682J 152J 10 392J 122J 103J 0 0.001 0.01 0.1 Frequency(MHz) 1 10 ○ Measurement equipment Product No. Manufacturer 4294A Agilent Technologies ＊ Equivalent measurement equipment may be used. • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm (12/12) I N D U C T O R S NL series Packaging Style REEL DIMENSIONS 2.0±0.5 B Type NL453232 NL565050 A ø180 ø180 B 17 17 C ø60 ø60 D 13 13 E 0.5 0.5 C * These values are typical values. (1.0) ø13.0±0.5 E D ø21.0±0.8 A Dimensions in mm P2 P0 P1 K t A0 Type NL453232 NL565050 A0 3.6 5.4 B0 4.9 5.8 øD0 1.5+0.1/-0 1.5+0.1/-0 B0 W F øD0 E TAPE DIMENSIONS Dimensions in mm E F P0 P1 P2 W 1.75±0.1 5.50±0.05 4.00±0.10 8.00±0.10 2.00±0.05 12.0±0.30 1.75±0.1 5.50±0.05 4.00±0.10 8.00±0.10 2.00±0.05 12.0±0.30 K 3.2 5.4 t 0.4 0.4 • All specifications are subject to change without notice. 001-01 / 20130516 / e511_nl.fm