ADS8412 SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 16-BIT, 2 MSPS, UNIPOLAR DIFFERENTIAL INPUT, MICROPOWER SAMPLING ANALOG-TO-DIGITAL CONVERTER WITH PARALLEL INTERFACE AND REFERENCE FEATURES APPLICATIONS • • • • • • • • • • • • • • • 2-MHz Sample Rate 16-Bit NMC Ensured Over Temperature Zero Latency Unipolar Differential Input Range: Vref to -Vref Onboard Reference Onboard Reference Buffer High-Speed Parallel Interface Power Dissipation: 175 mW at 2 MHz Typ Wide Digital Supply 8-/16-Bit Bus Transfer 48-Pin TQFP Package ESD Sensitive - HBM Capability of 500 V, 1000 V at All Input Pins • • • DWDM Instrumentation High-Speed, High-Resolution, Zero Latency Data Acquisition Systems Transducer Interface Medical Instruments Communication DESCRIPTION The ADS8412 is a 16-bit, 2 MHz A/D converter with an internal 4.096-V reference. The device includes a 16-bit capacitor-based SAR A/D converter with inherent sample and hold. The ADS8412 offers a full 16-bit interface and an 8-bit option where data is read using two 8-bit read cycles. The ADS8412 has a unipolar differential input. It is available in a 48-lead TQFP package and is characterized over the industrial -40°C to 85°C temperature range. SAR +IN -IN + _ Output Latches and 3-State Drivers CDAC BYTE 16-/8-Bit Parallel DATA Output Bus Comparator RESET REFIN REFOUT 4.096-V Internal Reference Clock Conversion and Control Logic CONVST BUSY CS RD Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2004, Texas Instruments Incorporated ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. ORDERING INFORMATION (1) MODEL MAXIMUM INTEGRAL LINEARITY (LSB) MAXIMUM DIFFERENTIAL LINEARITY (LSB) NO MISSING CODES RESOLUTION (BIT) PACKAGE TYPE PACKAGE DESIGNATOR TEMPERATURE RANGE ADS8412I –6 ~ 6 –2~+3 15 48 Pin TQFP PFB –40°C to 85°C 48 Pin TQFP PFB ADS8412IB (1) –2.5 ~ 2.5 –1~+2 16 ORDERING INFORMATION TRANSPORT MEDIA QUANTITY ADS8412IPFBT Tape and reel 250 ADS8412IPFBR Tape and reel 1000 ADS8412IBPFBT Tape and reel 250 ADS8412IBPFBR Tape and reel 1000 –40°C to 85°C For the most current specifications and package information, refer to our website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) UNIT Voltage Voltage range +IN to AGND –0.4 V to +VA + 0.1 V –IN to AGND –0.4 V to +VA + 0.1 V +VA to AGND –0.3 V to 7 V +VBD to BDGND –0.3 V to 7 V +VA to +VBD –0.3 V to 2.55 V Digital input voltage to BDGND –0.3 V to +VBD + 0.3 V Digital output voltage to BDGND –0.3 V to +VBD + 0.3 V Operating free-air temperature range, TA –40°C to 85°C Storage temperature range, Tstg –65°C to 150°C Junction temperature (TJ max) TQFP package 2 (TJMax - TA)/θJA θJA thermal impedance Lead temperature, soldering (1) 150°C Power dissipation 86°C/W Vapor phase (60 sec) 215°C Infrared (15 sec) 220°C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 SPECIFICATIONS TA = –40°C to 85°C, +VA = 5 V, +VBD = 3 V or 5 V, Vref = 4.096 V, fSAMPLE = 2 MHz (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT ANALOG INPUT Full-scale input voltage (1) Absolute input voltage Common-mode input range +IN – (–IN) –Vref Vref +IN –0.2 Vref + 0.2 –IN –0.2 Vref + 0.2 ADS8412I (Vref/2) – 0.2 Vref/2 (Vref/2) + 0.2 V V V Input capacitance 25 pF Input leakage current 0.5 nA 16 Bits SYSTEM PERFORMANCE Resolution No missing codes (2) (3) ADS8412I 15 ADS8412IB 16 –6 ±4 6 –2.5 ±1.5 2.5 ADS8412I –2 ±1 3 ADS8412IB –1 ±0.8 2 ADS8412I INL Integral linearity DNL Differential linearity EO Offset error EG Gain error (4) (5) CMRR Common-mode rejection ratio (4) ADS8412IB ADS8412I ADS8412IB ADS8412I ADS8412IB –3 ±1 3 –1.5 ±0.5 1.5 –0.15 0.15 –0.098 0.098 At dc (±0.2 V around Vref/2) 80 +IN – (–IN) = 1 Vpp at 1 MHz 80 Noise PSRR Bits DC Power supply rejection ratio At 7FFFh output code, +VA = 4.75 V to 5.25 V, Vref = 4.096 V (4) LSB LSB mV %FS dB 60 µV RMS 1 LSB SAMPLING DYNAMICS Conversion time 340 Acquisition time 100 400 ns ns Throughput rate 2 MHz Aperture delay 2 ns Aperture jitter 25 ps Step response 100 ns Overvoltage recovery 100 ns DYNAMIC CHARACTERISTICS VIN = 8 Vpp at 100 kHz –95 VIN = 8 Vpp at 500 kHz –90 Signal-to-noise ratio VIN = 8 Vpp at 100 kHz 90 Signal-to-noise + distortion VIN = 8 Vpp at 100 kHz 88 VIN = 8 Vpp at 100 kHz 95 VIN = 8 Vpp at 500 kHz 93 THD Total harmonic distortion (6) SNR SINAD SFDR Spurious free dynamic range –3 dB Small signal bandwidth (1) (2) (3) (4) (5) (6) 5 dB dB dB MHz Ideal input span, does not include gain or offset error. LSB means least significant bit This is endpoint INL, not best fit Measured relative to an ideal full-scale input [+IN – (–IN)] of 8.192 V This specification does not include the internal reference voltage error and drift. Calculated on the first nine harmonics of the input frequency 3 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 SPECIFICATIONS (continued) TA = –40°C to 85°C, +VA = 5 V, +VBD = 3 V or 5 V, Vref = 4.096 V, fSAMPLE = 2 MHz (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP MAX 3.9 4.096 4.2 UNIT EXTERNAL VOLTAGE REFERENCE INPUT Vref Reference voltage at REFIN Reference resistance (7) 500 V kΩ INTERNAL REFERENCE OUTPUT Vref Internal reference start-up time From 95% (+VA), with 1 µF storage capacity Reference voltage IOUT = 0 Source current Static load Line regulation +VA = 4.75 ~ 5.25 V 0.6 mV Drift IOUT = 0 36 PPM/°C 120 4.065 4.096 ms 4.13 V 10 µA DIGITAL INPUT/OUTPUT Logic family — CMOS VIH High level input voltage IIH = 5 µA +VBD – 1 VIL Low level input voltage IIL = 5 µA –0.3 +VBD + 0.3 0.8 VOH High level output voltage IOH = 2 TTL loads +VBD – 0.6 +VBD VOL Low level output voltage IOL = 2 TTL loads 0 0.4 V Data format – 2's complement POWER SUPPLY REQUIREMENTS Power supply voltage PD +VBD +VA 2.7 3 5.25 4.75 5 5.25 V +VA Supply current (8) fs = 2 MHz 35 40 mA Power dissipation (8) fs = 2 MHz 175 200 mW 85 °C TEMPERATURE RANGE TA (7) (8) 4 Operating free-air –40 Can vary ±20% This includes only +VA current. +VBD current is typically 1 mA with 5-pF load capacitance on output pins. ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TIMING CHARACTERISTICS All specifications typical at –40°C to 85°C, +VA = +VBD = 5 V (1) (2) (3) PARAMETER MIN tCONV Conversion time 340 tACQ Acquisition time 100 tpd1 CONVST low to BUSY high tpd2 Propagation delay time, end of conversion to BUSY low tw1 Pulse duration, CONVST low tsu1 Setup time, CS low to CONVST low tw2 Pulse duration, CONVST high TYP MAX UNIT 400 ns ns 30 ns 5 ns 20 ns 0 ns 20 ns CONVST falling edge jitter 10 tw3 Pulse duration, BUSY signal low tw4 Pulse duration, BUSY signal high th1 Hold time, first data bus data transition (RD low, or CS low for read cycle, or BYTE input changes) after CONVST low td1 tsu2 tw5 Pulse duration, RD low ten Enable time, RD low (or CS low for read cycle) to data valid td2 Delay time, data hold from RD high 0 td3 Delay time, BYTE rising edge or falling edge to data valid 2 tw6 Pulse duration, RD high 20 ns tw7 Pulse duration, CS high 20 ns th2 Hold time, last RD (or CS for read cycle ) rising edge to CONVST falling edge 50 ns tsu3 Setup time, BYTE transition to RD falling edge 0 ns th3 Hold time, BYTE transition to RD falling edge 0 tdis Disable time, RD high (CS high for read cycle) to 3-stated data bus 20 ns td5 Delay time, end of conversion to MSB data valid 10 ns tsu4 Byte transition setup time, from BYTE transition to the next BYTE transition 50 ns td6 Delay time, CS rising edge to BUSY falling edge 50 ns td7 Delay time, BUSY falling edge to CS rising edge 50 ns tsu(AB) Setup time, from the falling edge of CONVST (used to start the valid conversion) to the next falling edge of CONVST (when CS = 0 and CONVST used to abort) or to the next falling edge of CS (when CS is used to abort) 60 tsu5 Setup time, falling edge of CONVST to read valid data (MSB) from current conversion th4 Hold time, data (MSB) from previous conversion hold valid from falling edge of CONVST (1) (2) (3) Min(tACQ) ps ns 370 ns 40 ns Delay time, CS low to RD low (or BUSY low to RD low) 0 ns Setup time, RD high to CS high 0 ns 50 ns 20 ns ns 20 ns ns 340 MAX(tCONV) + MAX(td5) ns ns MIN(tCONV) ns All input signals are specified with tr = tf = 5 ns (10% to 90% of +VBD) and timed from a voltage level of (VIL + VIH)/2. See timing diagrams. All timings are measured with 20 pF equivalent loads on all data bits and BUSY pins. 5 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TIMING CHARACTERISTICS All specifications typical at –40°C to 85°C, +VA = 5 V, +VBD = 3 V (1) (2) (3) PARAMETER MIN TYP MAX UNIT 400 ns tCONV Conversion time 340 tACQ Acquisition time 100 tpd1 CONVST low to conversion started (BUSY high) 40 ns tpd2 Propagation delay time, end of conversion to BUSY low 10 ns tw1 Pulse duration, CONVST low tsu1 Setup time, CS low to CONVST low tw2 Pulse duration, CONVST high ns 20 ns 0 ns 20 ns CONVST falling edge jitter 10 tw3 Pulse duration, BUSY signal low tw4 Pulse duration, BUSY signal high th1 Hold time, first data bus transition (RD low, or CS low for read cycle, or BYTE input changes) after CONVST low td1 tsu2 tw5 Pulse duration, RD low ten Enable time, RD low (or CS low for read cycle) to data valid td2 Delay time, data hold from RD high 0 td3 Delay time, BYTE rising edge or falling edge to data valid 2 tw6 Pulse duration, RD high 20 ns tw7 Pulse duration, CS high 20 ns th2 Hold time, last RD (or CS for read cycle ) rising edge to CONVST falling edge 50 ns tsu3 Setup time, BYTE transition to RD falling edge 0 ns th3 Hold time, BYTE transition to RD falling edge 0 tdis Disable time, RD high (CS high for read cycle) to 3-stated data bus td5 Delay time, end of conversion to MSB data valid tsu4 Byte transition setup time, from BYTE transition to next BYTE transition 50 ns td6 Delay time, CS rising edge to BUSY falling edge 50 ns td7 Delay time, BUSY falling edge to CS rising edge 50 ns tsu(AB) Setup time, from the falling edge of CONVST (used to start the valid conversion) to the next falling edge of CONVST (when CS = 0 and CONVST used to abort) or to the next falling edge of CS (when CS is used to abort) 70 tsu5 Setup time, falling edge of CONVST to read valid data (MSB) from current conversion th4 Hold time, data (MSB) from previous conversion hold valid from falling edge of CONVST (1) (2) (3) 6 Min(tACQ) ps ns 370 ns 40 ns Delay time, CS low to RD low (or BUSY low to RD low) 0 ns Setup time, RD high to CS high 0 ns 50 ns 30 ns ns 30 ns ns 30 ns 20 ns 350 MAX(tCONV) + MAX(td5) ns ns MIN(tCONV) All input signals are specified with tr = tf = 5 ns (10% to 90% of +VBD) and timed from a voltage level of (VIL + VIH)/2. See timing diagrams. All timings are measured with 20 pF equivalent loads on all data bits and BUSY pins. ns ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 PIN ASSIGNMENTS BUSY BDGND +VBD DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 BDGND PFB PACKAGE (TOP VIEW) 36 35 34 33 32 31 30 29 28 27 26 25 37 24 38 23 39 22 40 21 41 20 42 19 43 18 44 17 45 16 46 15 47 14 48 3 4 5 6 7 8 13 9 10 11 12 REFIN REFOUT NC +VA AGND +IN -IN AGND +VA +VA 1 2 +VBD DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 AGND AGND +VA AGND AGND +VBD RESET BYTE CONVST RD CS +VA AGND AGND +VA REFM REFM NC - No connection 7 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 Terminal Functions NAME NO. I/O 5, 8, 11, 12, 14, 15, 44, 45 - Analog ground 25, 35 - Digital ground for bus interface digital supply BUSY 36 O Status output. High when a conversion is in progress. BYTE 39 I Byte select input. Used for 8-bit bus reading. 0: No fold back 1: Low byte D[7:0] of the 16 most significant bits is folded back to high byte of the 16 most significant pins DB[15:8]. CONVST 40 I Convert start. The falling edge of this input ends the acquisition period and starts the hold period. CS 42 I Chip select. The falling edge of this input starts the acquisition period. AGND BDGND DESCRIPTION 8-Bit Bus Data Bus BYTE = 0 16-Bit Bus BYTE = 1 BYTE = 0 DB15 16 O D15 (MSB) D7 D15 (MSB) DB14 17 O D14 D6 D14 DB13 18 O D13 D5 D13 DB12 19 O D12 D4 D12 DB11 20 O D11 D3 D11 DB10 21 O D10 D2 D10 DB9 22 O D9 D1 D9 DB8 23 O D8 D0 (LSB) D8 DB7 26 O D7 All ones D7 DB6 27 O D6 All ones D6 DB5 28 O D5 All ones D5 DB4 29 O D4 All ones D4 DB3 30 O D3 All ones D3 DB2 31 O D2 All ones D2 DB1 32 O D1 All ones D1 DB0 33 O D0 (LSB) All ones D0 (LSB) –IN 7 I Inverting input channel +IN 6 I Non inverting input channel NC 3 - No connection REFIN 1 I Reference input REFM 47, 48 I Reference ground REFOUT 2 O Reference output. Add 1 µF capacitor between the REFOUT pin and REFM pin when internal reference is used. RESET 38 I Current conversion is aborted and output latches are cleared (set to zeros) when this pin is asserted low. RESET works independantly of CS. RD 41 I Synchronization pulse for the parallel output. When CS is low, this serves as the output enable and puts the previous conversion result on the bus. +VA 4, 9, 10, 13, 43, 46 - Analog power supplies, 5-V dc 24, 34, 37 - Digital power supply for bus +VBD 8 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TIMING DIAGRAMS tw2 tw1 CONVST (used in normal conversion) tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tpd1 tw3 BUSY tsu1 tw7 td7 CS td6 CONVERT† tCONV tCONV SAMPLING† (When CS Toggle) tACQ BYTE tsu4 th1 tsu2 td1 th2 RD Data to be read† Invalid Previous Conversion th4 tdis ten tsu5 DB[15:8] Invalid Current Conversion Hi−Z Hi−Z D [15:8] DB[7:0] Hi−Z D [7:0] Hi−Z D [7:0] †Signal internal to device Figure 1. Timing for Conversion and Acquisition Cycles With CS and RD Toggling 9 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 tw1 CONVST (used in normal conversion) tw2 tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tw3 BUSY tw7 tsu1 td7 CS td6 CONVERT† tCONV tCONV SAMPLING† (When CS Toggle) tACQ BYTE th1 RD = 0 Data to be read† tdis ten DB[15:8] DB[7:0] †Signal tsu5 Hi−Z Previous D [7:0] Hi−Z internal to device Invalid Current Conversion Previous Hi−Z D [15:8] Hi−Z tdis Invalid Previous Conversion th4 tsu4 th2 ten D [15:8] D [7:0] D [7:0] Hi−Z Repeated D [15:8] Hi−Z Repeated D [7:0] ten Figure 2. Timing for Conversion and Acquisition Cycles With CS Toggling, RD Tied to BDGND 10 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 tw1 tw2 CONVST (used in normal conversion) tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tpd1 tw3 BUSY CS = 0 CONVERT† tCONV tCONV t(ACQ) SAMPLING† (When CS = 0) BYTE tsu4 th1 th2 RD tdis ten Data to be read† th4 DB[15:8] DB[7:0] †Signal Invalid Invalid Previous Conversion Current Conversion tsu5 Hi−Z Hi−Z D [15:8] D [7:0] D [7:0] Hi−Z Hi−Z internal to device Figure 3. Timing for Conversion and Acquisition Cycles With CS Tied to BDGND, RD Toggling 11 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 tw1 CONVST (used in normal conversion) tw2 tcycle CONVST (used in ABORT) tsu(AB) tpd1 tsu(AB) tpd2 tw4 tpd1 tpd2 tw3 BUSY CS = 0 CONVERT† tCONV tCONV tACQ SAMPLING† (When CS Toggle) th1 th1 BYTE RD = 0 td3 td3 td5 th4 tsu5 Previous MSB Invalid DB[15:8] Previous Previous LSB LSB Invalid DB[7:0] †Signal td5 th4 td3 tsu5 Invalid MSB LSB MSB MSB LSB MSB Invalid internal to device Figure 4. Timing for Conversion and Acquisition Cycles With CS and RD Tied to BDGND—Auto Read CS RD tsu4 BYTE ten tdis tdis ten DB[15:0] td3 Hi−Z Valid Hi−Z Valid Valid Figure 5. Detailed Timing for Read Cycles 12 Hi−Z ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TYPICAL CHARACTERISTICS SIGNAL-TO-NOISE RATIO vs FREE-AIR TEMPERATURE HISTOGRAM (DC Code Spread) HALF SCALE 131071 CONVERSIONS 80000 90.4 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Code = 65292 60000 SNR − Signal-to-Noise Ratio − dB 70000 50000 40000 30000 20000 10000 90.2 90.1 90 89.9 89.8 89.7 89.6 89.5 −40 65295 65292 65289 0 Figure 7. EFFECTIVE NUMBER OF BITS vs FREE-AIR TEMPERATURE SIGNAL-TO-NOISE AND DISTORTION vs FREE-AIR TEMPERATURE 80 86.2 SINAD − Signal-to-Nois and Distortion − dB 14.015 14.01 14.005 14 13.995 fi = 50 kHz, +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference 13.99 13.985 13.98 −40 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 6. 14.02 ENOB − Effective Number of Bits − Bits fi = 50 kHz, +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference 90.3 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 8. 80 86.15 86.1 86.05 fi = 50 kHz, +VA = 5 V, +VBD = 3.3 V, Internal Reference 86 85.95 85.9 −40 −20 0 20 40 60 TA − Free-Air Temperature − °C 80 Figure 9. At –40°C to 85°C, +VA = 5 V, +VBD = 5 V, REFIN = 4.096 V (internal reference used) and fsample = 2 MHz (unless otherwise noted) 13 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) SPURIOUS FREE DYNAMIC RANGE vs FREE-AIR TEMPERATURE TOTAL HARMONIC DISTORTION vs FREE-AIR TEMPERATURE 100.5 100 −93.8 fi = 100 kHz, +VA = 5 V, +VBD = 3.3 V, Internal Reference 99.5 99 98.5 98 97.5 97 96.5 −40 −20 0 20 40 60 −94.4 −94.6 −94.8 −95 −95.2 −95.4 TA − Free-Air Temperature − °C −95.8 −40 80 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 10. Figure 11. SIGNAL-TO-NOISE RATIO vs INPUT FREQUENCY EFFECTIVE NUMBER OF BITS vs INPUT FREQUENCY 80 14.45 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference 91 90.8 ENOB − Effective Number of Bits − Bits SNR − Signal-to-Noise Ratio − dB −94.2 −95.6 91.2 90.6 90.4 90.2 90 89.8 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference 14.4 14.35 14.3 14.25 14.2 14.15 14.1 14.05 14 13.95 13.9 0 20 40 60 80 fi − Input Frequency − kHz Figure 12. 14 fi = 100 kHz, +VA = 5 V, +VBD = 3.3 V, Internal Reference −94 THD − Total Harmonic Distortion − dB SFDR − Spurious Free Dynamic Range − dB 101 100 0 20 40 60 80 fi − Input Frequency − kHz Figure 13. 100 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) SIGNAL-TO-NOISE AND DISTORTION vs INPUT FREQUENCY SPURIOUS FREE DYNAMIC RANGE vs INPUT FREQUENCY 103 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference 88.5 88 SFDR − Spurious Free Dynamic Range − dB SINAD − Signal-to-Nois and Distortion − dB 89 87.5 87 86.5 86 85.5 0 20 40 60 80 fi − Input Frequency − kHz 100 99 98 97 0 20 40 60 80 fi − Input Frequency − kHz Figure 15. TOTAL HARMONIC DISTORTION vs INPUT FREQUENCY SUPPLY CURRENT vs SAMPLE RATE 100 34 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference −95 33.5 ICC − Supply Current − mA −94 THD − Total Harmonic Distortion − dB 101 Figure 14. −93 −96 −97 −98 −99 −100 33 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Referance 32.5 32 31.5 31 30.5 30 −101 −102 102 96 100 +VA = 5 V, +VBD = 3.3 V, TA = 25°C, Internal Reference 29.5 0 20 40 60 80 fi − Input Frequency − kHz Figure 16. 100 29 500 1000 1500 Samply Rate − KSPS 2000 Figure 17. 15 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) GAIN ERROR vs SUPPLY VOLTAGE (VA+) OFFSET ERROR vs SUPPLY VOLTAGE (VA+) 0.6 0.14 +VBD = 3.3 V, TA = 25°C, External Reference 0.12 EO − Offset Error − mV E G − Gain Error − mV 0.5 0.4 0.3 0.2 0.1 0 4.75 0.08 0.06 0.04 +VBD = 3.3 V, TA = 25°C, External Reference 0.02 4.85 4.95 5.05 5.15 VDD − Supply Voltage − V 0 4.75 5.25 4.85 4.95 5.05 5.15 5.25 VDD − Supply Voltage − V Figure 18. Figure 19. INTERNAL VOLTAGE REFERENCE vs FREE-AIR TEMPERATURE GAIN ERROR vs FREE-AIR TEMPERATURE 1 4.091 +VA = 5 V, +VBD = 3.3 V 4.090 +VA = 5 V, +VBD = 3.3 V, External Reference 0.8 0.6 E G − Gain Error − mV Internal Voltage Reference − V 0.10 4.089 4.088 4.087 0.4 0.2 0 −0.2 −0.4 4.086 −0.6 4.085 −0.8 4.084 −40 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 20. 16 80 −1 −40 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 21. 80 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) OFFSET ERROR vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs FREE-AIR TEMPERATURE 34.8 0.1 +VA = 5 V, +VBD = 3.3 V, External Reference EO − Offset Error − mV 0.06 ICC − Supply Current − mA 0.08 0.04 0.02 0 −0.02 −0.04 34.2 34 33.8 33.6 33.2 −0.08 −20 0 20 40 60 TA − Free-Air Temperature − °C 33 −40 80 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 22. Figure 23. DIFFERENTIAL NONLINEARITY vs FREE-AIR TEMPERATURE INTEGRAL NONLINEARITY vs FREE-AIR TEMPERATURE 1.5 80 2 Max INL − Integral Nonlinearity − LSBs DNL − Differential Nonlinearity − LSBs 34.4 33.4 −0.06 −0.1 −40 +VA = 5 V, +VBD = 3.3 V 34.6 +VA = 5 V, +VBD = 3.3 V, Internal Reference 1 0.5 0 −0.5 Min −1 −1.5 −40 −20 0 20 40 60 TA − Free-Air Temperature − °C Figure 24. 80 1.5 MAX 1 0.5 0 −0.5 MIN −1 −1.5 −2 −40 −25 −10 5 20 35 50 65 80 TA − Free-Air Temperature − °C Figure 25. 17 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 TYPICAL CHARACTERISTICS (continued) 4 3 DNL − LSBs 2 1 0 −1 −2 −3 −4 0 16384 32768 Code Figure 26. 49152 65536 0 16384 32768 Code Figure 27. 49152 65536 4 INL − LSBs 3 2 1 0 −1 −2 −3 −4 Magnitude - dB FFT 0 -20 -40 -60 -80 -100 -120 -140 -160 -180 -200 0 100 200 300 400 500 600 Frequency - kHz Figure 28. 18 700 800 900 1000 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 APPLICATION INFORMATION MICROCONTROLLER INTERFACING ADS8412 to 8-Bit Microcontroller Interface Figure 29 shows a parallel interface between the ADS8412 and a typical microcontroller using the 8-bit data bus. The BUSY signal is used as a falling-edge interrupt to the microcontroller. Analog 5 V 0.1 µF AGND 10 µF Ext Ref Input 0.1 µF 1 µF Micro Controller -IN REFM AGND +IN +VA REFIN Analog Input Digital 3 V GPIO CS BYTE GPIO P[7:0] ADS8412 DB[15:8] RD CONVST BUSY RD GPIO INT 0.1 µF BDGND BDGND +VBD Figure 29. ADS8412 Application Circuitry (using external reference) Analog 5 V 0.1 µF AGND 10 µF 0.1 µF AGND REFM REFIN REFOUT +VA 1 µF AGND ADS8412 Figure 30. Use Internal Reference 19 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 PRINCIPLES OF OPERATION The ADS8412 is a high-speed successive approximation register (SAR) analog-to-digital converter (ADC). The architecture is based on charge redistribution, which inherently includes a sample/hold function. See Figure 29 for the application circuit for the ADS8412. The conversion clock is generated internally. The conversion time of 400 ns is capable of sustaining a 2-MHz throughput. The analog input is provided to two input pins: +IN and –IN. When a conversion is initiated, the differential input on these pins is sampled on the internal capacitor array. While a conversion is in progress, both inputs are disconnected from any internal function. REFERENCE The ADS8412 can operate with an external reference with a range from 3.9 V to 4.2 V. A 4.096-V internal reference is included. When internal reference is used, pin 2 (REFOUT) should be connected to pin 1 (REFIN) with an 0.1 µF decoupling capacitor and 1 µF storage capacitor between pin 2 (REFOUT) and pins 47 and 48 (REFM) (see Figure 33). The internal reference of the converter is double buffered. If an external reference is used, the second buffer provides isolation between the external reference and the CDAC. This buffer is also used to recharge all of the capacitors of the CDAC during conversion. Pin 2 (REFOUT) can be left unconnected (floating) if external reference is used. ANALOG INPUT When the converter enters the hold mode, the voltage difference between the +IN and -IN inputs is captured on the internal capacitor array. Both +IN and -IN input has a range of –0.2 V to Vref + 0.2 V. The input span(+IN – (–IN)) is limited to –Vref to Vref. The input current on the analog inputs depends upon a number of factors: sample rate, input voltage, and source impedance. Essentially, the current into the ADS8412 charges the internal capacitor array during the sample period. After this capacitance has been fully charged, there is no further input current. The source of the analog input voltage must be able to charge the input capacitance (25 pF) to an 16-bit settling level within the acquisition time (100 ns) of the device. When the converter goes into the hold mode, the input impedance is greater than 1 GΩ. Care must be taken regarding the absolute analog input voltage. To maintain the linearity of the converter, the +IN and –IN inputs and the span (+IN – (–IN)) should be within the limits specified. Outside of these ranges, the converter's linearity may not meet specifications. To minimize noise, low bandwidth input signals with low-pass filters should be used. Care should be taken to ensure that the output impedance of the sources driving +IN and –IN inputs are matched. If this is not observed, the two inputs could have different setting time. This may result in offset error, gain error and linearity error which varies with temperature and input voltage. A typical input circuit using TI's THS4503 is shown Figure 31. Input from a single-ended source may be converted into differential signal for ADS8412 as shown in the figure. In case the source itself is differential then THS4503 may be used in differential input and differential output mode. 20 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 PRINCIPLES OF OPERATION (continued) 68 pF RS RG RT 1 kΩ 50 Ω VCC+ + _ 20 pF THS4503 _ + + _ INADS8412 IN+ OCM VCC1 kΩ RG, RS, and RT should be chosen such that RG + RS || RT = 1 k Ω VOCM = 2 V, +VCC = 7 V, and -VCC = -7 V 1 kΩ 50 Ω 68 pF Figure 31. Using THS4503 With ADS8412 DIGITAL INTERFACE Timing And Control See the timing diagrams in the specifications section for detailed information on timing signals and their requirements. The ADS8412 uses an internal oscillator generated clock which controls the conversion rate and in turn the throughput of the converter. No external clock input is required. Conversions are initiated by bringing the CONVST pin low for a minimum of 20 ns (after the 20 ns minimum requirement has been met, the CONVST pin can be brought high), while CS is low. The ADS8412 switches from the sample to the hold mode on the falling edge of the CONVST command. A clean and low jitter falling edge of this signal is important to the performance of the converter. The BUSY output is brought high after CONVST goes low. BUSY stays high throughout the conversion process and returns low when the conversion has ended. Sampling starts when CS is tied low or starts with the falling edge of CS when BUSY is low. Both RD and CS can be high during and before a conversion with one exception (CS must be low when CONVST goes low to initiate a conversion). Both the RD and CS pins are brought low in order to enable the parallel output bus with the conversion. Reading Data The ADS8412 outputs full parallel data in two's complement format as shown in Table 1. The parallel output is active when CS and RD are both low. There is a minimal quiet zone requirement around the falling edge of CONVST. This is 50 ns prior to the falling edge of CONVST and 40 ns after the falling edge. No data read should be attempted within this zone. Any other combination of CS and RD sets the parallel output to 3-state. BYTE is used for multiword read operations. BYTE is used whenever lower bits of the conversion result are output on the higher byte of the bus. Refer to Table 1 for ideal output codes. 21 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 Table 1. Ideal Input Voltages and Output Codes DESCRIPTION DIGITAL OUTPUT – TWOS COMPLEMENT ANALOG VALUE BINARY CODE HEX CODE Full Scale Range 2(+Vref) Least significant bit (LSB) 2(+Vref)/65536 +Full scale (+Vref) – 1 LSB 0111 1111 1111 1111 7FFF Midscale 0V 0000 0000 0000 0000 0000 Midscale – 1 LSB 0 V – 1 LSB 1111 1111 1111 1111 FFFF –Full scale (–Vref) 1000 0000 0000 0000 8000 The output data is a full 16-bit word (D15-D0) on DB15-DB0 pins (MSB-LSB) if BYTE is low. The result may also be read on an 8-bit bus for convenience. This is done by using only pins DB15-DB8. In this case two reads are necessary: the first as before, leaving BYTE low and reading the 8 most significant bits on pins DB15-DB8, then bringing BYTE high. When BYTE is high, the low bits (D7-D0) appears on pins DB15-D8. These multiword read operations can be done with multiple active RD (toggling) or with RD tied low for simplicity. Table 2. Conversion Data Readout BYTE DATA READ OUT DB15–DB8 Pins DB7–DB0 Pins High D7–D0 All one's Low D15–D8 D7–D0 RESET RESET is an asynchronous active low input signal (that works independantly of CS). Minimum RESET low time is 25 ns. Current conversion will be aborted no later than 50 ns after the converter is in the reset mode. In addition, all output latches are cleared (set to zero's) after RESET. The converter goes back to normal operation mode no later than 20 ns after RESET input is brought high. The converter starts the first sampling period 20 ns after the rising edge of RESET. Any sampling period except for the one immediately after a RESET is started with the falling edge of the previous BUSY signal or the falling edge of CS, whichever is later. Another way to reset the device is through the use of the combination of CS and CONVST. This is useful when the dedicated RESET pin is tied to the system reset but there is a need to abort only the conversion in a specific converter. Since the BUSY signal is held high during the conversion, either one of these conditions triggers an internal self-clear reset to the converter just the same as a reset via the dedicated RESET pin. The reset does not have to be cleared as for the dedicated RESET pin. A reset can be started with either of the two following steps. • Issue a CONVST when CS is low and a conversion is in progress. The falling edge of CONVST must satisfy the timing as specified by the timing parameter tsu(AB) mentioned in the timing characteristics table to ensure a reset. The falling edge of CONVST starts a reset. Timing is the same as a reset using the dedicated RESET pin except the instance of the falling edge is replaced by the falling edge of CONVST. • Issue a CS while a conversion is in progress. The falling edge of CS must satisfy the timing as specified by the timing parameter tsu(AB) mentioned in the timing characteristics table to ensure a reset. The falling edge of CONVST starts a reset. The falling edge of CS causes a reset. Timing is the same as a reset using the dedicated RESET pin except the instance of the falling edge is replaced by the falling edge of CS. POWER-ON INITIALIZATION RESET is not required after power on. An internal power-on reset circuit generates the reset. To ensure that all of the registers are cleared, three conversion cycles must be given to the converter after power on. 22 ADS8412 www.ti.com SLAS384A – JUNE 2003 – REVISED DECEMBER 2004 LAYOUT For optimum performance, care should be taken with the physical layout of the ADS8412 circuitry. As the ADS8412 offers single-supply operation, it is often used in close proximity with digital logic, microcontrollers, microprocessors, and digital signal processors. The more digital logic present in the design and the higher the switching speed, the more difficult it is to achieve good performance from the converter. The basic SAR architecture is sensitive to glitches or sudden changes on the power supply, reference, ground connections and digital inputs that occur just prior to latching the output of the analog comparator. Thus, driving any single conversion for an n-bit SAR converter, there are at least n windows in which large external transient voltages can affect the conversion result. Such glitches might originate from switching power supplies, nearby digital logic, or high power devices. The degree of error in the digital output depends on the reference voltage, layout, and the exact timing of the external event. On average, the ADS8412 draws very little current from an external reference, as the reference voltage is internally buffered. If the reference voltage is external and originates from an op amp, make sure that it can drive the bypass capacitor or capacitors without oscillation. A 0.1-µF bypass capacitor and 1-µF storage capacitor are recommended from pin 1 (REFIN) directly to pin 48 (REFM). REFM and AGND should be shorted on the same ground plane under the device. The AGND and BDGND pins should be connected to a clean ground point. In all cases, this should be the analog ground. Avoid connections which are close to the grounding point of a microcontroller or digital signal processor. If required, run a ground trace directly from the converter to the power supply entry point. The ideal layout consists of an analog ground plane dedicated to the converter and associated analog circuitry. As with the AGND connections, +VA should be connected to a 5-V power supply plane or trace that is separate from the connection for digital logic until they are connected at the power entry point. Power to the ADS8412 should be clean and well bypassed. A 0.1-µF ceramic bypass capacitor should be placed as close to the device as possible. See Table 3 for the placement of the capacitor. In addition, a 1-µF to 10-µF capacitor is recommended. In some situations, additional bypassing may be required, such as a 100-µF electrolytic capacitor or even a Pi filter made up of inductors and capacitors—all designed to essentially low-pass filter the 5-V supply, removing the high frequency noise. Table 3. Power Supply Decoupling Capacitor Placement POWER SUPPLY PLANE SUPPLY PINS CONVERTER ANALOG SIDE CONVERTER DIGITAL SIDE Pin pairs that require shortest path to decoupling capacitors (4,5), (8,9), (10,11), (13,15), (43,44), (45,46) (24,25), (34, 35) Pins that require no decoupling 12, 14 37 23 PACKAGE OPTION ADDENDUM www.ti.com 1-Apr-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty ADS8412IBPFBR ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS8412IBPFBRG4 ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS8412IBPFBT ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS8412IBPFBTG4 ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS8412IPFBR ACTIVE TQFP PFB 48 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS8412IPFBT ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS8412IPFBTG4 ACTIVE TQFP PFB 48 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 MECHANICAL DATA MTQF019A – JANUARY 1995 – REVISED JANUARY 1998 PFB (S-PQFP-G48) PLASTIC QUAD FLATPACK 0,27 0,17 0,50 36 0,08 M 25 37 24 48 13 0,13 NOM 1 12 5,50 TYP 7,20 SQ 6,80 9,20 SQ 8,80 Gage Plane 0,25 0,05 MIN 0°– 7° 1,05 0,95 Seating Plane 0,75 0,45 0,08 1,20 MAX 4073176 / B 10/96 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Falls within JEDEC MS-026 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated