SCDS037J − DECEMBER 1997 − REVISED OCTOBER 2003 D Standard ’125-Type Pinout D 5-Ω Switch Connection Between Two Ports D Rail-to-Rail Switching on Data I/O Ports 13 3 12 4 11 5 10 6 9 7 8 VCC 4OE 4A 4B 3OE 3A 3B 1 1A 1B 2OE 2A 2B DBQ PACKAGE (TOP VIEW) VCC 14 2 NC 1OE 1A 1B 2OE 2A 2B GND 14 2 13 4OE 3 12 4A 4 11 4B 5 10 3OE 9 3A 6 7 8 3B 1 Operation Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II RGY PACKAGE (TOP VIEW) GND 1OE 1A 1B 2OE 2A 2B GND D 1OE D, DGV, NS, OR PW PACKAGE (TOP VIEW) D Ioff Supports Partial-Power-Down Mode 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 VCC 4OE 4A 4B 3OE 3A 3B NC NC − No internal connection description/ordering information The SN74CBTLV3125 quadruple FET bus switch features independent line switches. Each switch is disabled when the associated output-enable (OE) input is high. This device is fully specified for partial-power-down applications using Ioff. The Ioff feature ensures that damaging current will not backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION QFN − RGY TOP-SIDE MARKING Tape and reel SN74CBTLV3125RGYR Tube SN74CBTLV3125D Tape and reel SN74CBTLV3125DR SOP − NS Tape and reel SN74CBTLV3125NSR CBTLV3125 SSOP (QSOP) − DBQ Tape and reel SN74CBTLV3125DBQR CL125 TSSOP − PW Tape and reel SN74CBTLV3125PWR CL125 TVSOP − DGV Tape and reel SN74CBTLV3125DGVR SOIC − D −40°C 85°C −40 C to 85 C ORDERABLE PART NUMBER PACKAGE† TA CL125 CBTLV3125 CL125 † Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated !"#$ % &'!!($ #% )'*+&#$ ,#$(!,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (/#% %$!'"($% %$#,#!, 0#!!#$1- !,'&$ )!&(%%2 ,(% $ (&(%%#!+1 &+',( $(%$2 #++ )#!#"($(!%- • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 1 SCDS037J − DECEMBER 1997 − REVISED OCTOBER 2003 FUNCTION TABLE (each bus switch) INPUT OE FUNCTION L A port = B port H Disconnect logic diagram (positive logic) 3 2 1A 1OE 1B SW 1 6 5 2A 2B SW 4 2OE 9 8 3A 3B SW 10 3OE 12 11 4A SW 4B 13 4OE Pin numbers shown are for the D, DGV, NS, PW, and RGY packages. simplified schematic, each FET switch A B (OE) 2 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • SCDS037J − DECEMBER 1997 − REVISED OCTOBER 2003 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V Continuous channel current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128 mA Input clamp current, IIK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Package thermal impedance, θJA (see Note 2): D package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86°C/W (see Note 2): DBQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90°C/W (see Note 2): DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127°C/W (see Note 2): NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76°C/W (see Note 2): PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W (see Note 3): RGY package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The package thermal impedance is calculated in accordance with JESD 51-7. 3. The package thermal impedance is calculated in accordance with JESD 51-5. recommended operating conditions (see Note 4) VCC Supply voltage VIH High-level control input voltage VIL Low-level control input voltage VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V VCC = 2.3 V to 2.7 V VCC = 2.7 V to 3.6 V MIN MAX 2.3 3.6 UNIT V 1.7 V 2 0.7 0.8 V TA Operating free-air temperature −40 85 °C NOTE 4: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 3 SCDS037J − DECEMBER 1997 − REVISED OCTOBER 2003 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS MIN VIK II VCC = 3 V, VCC = 3.6 V, II = −18 mA VI = VCC or GND Ioff ICC VCC = 0, VCC = 3.6 V, VI or VO = 0 to 3.6 V IO = 0, VI = VCC or GND One input at 3 V, Other inputs at VCC or GND ∆ICC‡ Control inputs Ci Control inputs Cio(OFF) VCC = 3.6 V, VI = 3 V or 0 TYP† MAX UNIT −1.2 V ±1 µA 10 µA 10 µA 300 µA 2.5 VO = 3 V or 0, OE = VCC VCC = 2.3 V, TYP at VCC = 2.5 V ron§ VCC = 3 V pF 7 pF 5 8 VI = 0 II = 64 mA II = 24 mA 5 8 VI = 1.7 V, II = 15 mA 27 40 5 7 VI = 0 II = 64 mA II = 24 mA 5 7 Ω VI = 2.4 V, II = 15 mA 10 15 † All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C. ‡ This is the increase in supply current for each input that is at the specified voltage level, rather than VCC or GND. § Measured by the voltage drop between the A and B terminals at the indicated current through the switch. On-state resistance is determined by the lower of the voltages of the two (A or B) terminals. switching characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 1) VCC = 2.5 V ± 0.2 V FROM (INPUT) TO (OUTPUT) tpd¶ A or B B or A ten OE A or B 2 4.6 tdis OE A or B 1.1 3.9 PARAMETER MIN MAX VCC = 3.3 V ± 0.3 V MIN 0.15 UNIT MAX 0.25 ns 2 4.4 ns 1 4.2 ns ¶ The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). 4 • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • SCDS037J − DECEMBER 1997 − REVISED OCTOBER 2003 PARAMETER MEASUREMENT INFORMATION 2 × VCC RL From Output Under Test S1 Open GND CL (see Note A) TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND RL LOAD CIRCUIT VCC CL RL V∆ 2.5 V ±0.2 V 3.3 V ±0.3 V 30 pF 50 pF 500 Ω 500 Ω 0.15 V 0.3 V VCC Timing Input VCC/2 0V tw tsu VCC VCC/2 Input th VCC VCC/2 VCC/2 Data Input VCC/2 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC VCC/2 Input 0V tPHL tPLH VCC/2 VCC/2 VOL tPLH tPHL Output Waveform 2 S1 at GND (see Note B) VOH Output VCC/2 VCC/2 VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS VCC/2 0V t Output PZL Waveform 1 S1 at 2 × VCC (see Note B) VOH Output VCC Output Control VCC/2 tPLZ VCC VCC/2 VOL + V∆ VOL tPHZ tPZH VCC/2 VOH − V∆ VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2 ns, tf ≤ 2 ns. D. The outputs are measured one at a time with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms • POST OFFICE BOX 655303 DALLAS, TEXAS 75265 POST OFFICE BOX 1443 HOUSTON, TEXAS 77251−1443 • 5 MECHANICAL DATA MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000 DGV (R-PDSO-G**) PLASTIC SMALL-OUTLINE 24 PINS SHOWN 0,40 0,23 0,13 24 13 0,07 M 0,16 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 0°–8° 1 0,75 0,50 12 A Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,08 14 16 20 24 38 48 56 A MAX 3,70 3,70 5,10 5,10 7,90 9,80 11,40 A MIN 3,50 3,50 4,90 4,90 7,70 9,60 11,20 DIM 4073251/E 08/00 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side. Falls within JEDEC: 24/48 Pins – MO-153 14/16/20/56 Pins – MO-194 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MSOI002B – JANUARY 1995 – REVISED SEPTEMBER 2001 D (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 8 PINS SHOWN 0.020 (0,51) 0.014 (0,35) 0.050 (1,27) 8 0.010 (0,25) 5 0.008 (0,20) NOM 0.244 (6,20) 0.228 (5,80) 0.157 (4,00) 0.150 (3,81) Gage Plane 1 4 0.010 (0,25) 0°– 8° A 0.044 (1,12) 0.016 (0,40) Seating Plane 0.010 (0,25) 0.004 (0,10) 0.069 (1,75) MAX PINS ** 0.004 (0,10) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 4040047/E 09/01 NOTES: A. B. C. D. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Falls within JEDEC MS-012 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MSOI004E JANUARY 1995 – REVISED MAY 2002 DBQ (R–PDSO–G**) PLASTIC SMALL–OUTLINE PACKAGE 0.012 (0,30) 0.008 (0,20) 0.025 (0,64) 0.005 (0,13) 13 24 0.244 (6,20) 0.228 (5,80) 0.157 (3,99) 0.150 (3,81) 0.008 (0,20) NOM Gauge Plane 1 12 0.010 (0,25) A 0°–8° 0.035 (0,89) 0.016 (0,40) 0.069 (1,75) MAX Seating Plane 0.010 (0,25) 0.004 (0,10) 0.004 (0,10) PINS ** 16 20 24 28 A MAX 0.197 (5,00) 0.344 (8,74) 0.344 (8,74) 0.394 (10,01) A MIN 0.189 (4,80) 0.337 (8,56) 0.337 (8,56) 0.386 (9,80) M0–137 VARIATION AB AD AE AF DIM D 4073301/F 02/02 NOTES: A. All linear dimensions are in millimeters. B. This drawing is subject to change without notice. C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15). D. Falls within JEDEC MO–137. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0°– 8° A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Applications amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2003, Texas Instruments Incorporated