SM4933A THRU SM4937A 1.0 AMP SURFACE MOUNT FAST RECOVERY RECTIFIERS VOLTAGE RANGE 50 to 600 Volts CURRENT 1.0 Ampere FEATURES * Ideal for surface mount applications * Easy pick and place * Built-in strain relief * Fast switching speed DO-214AC(SMA) .110(2.79) .100(2.54) .058(1.47) .052(1.32) MECHANICAL DATA .177(4.50) .157(3.99) * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Metallurgically bonded construction * Polarity: Color band denotes cathode end * Mounting position: Any * Weight: 0.063 grams .012(0.31) .006(0.15) .090(2.29) .078(1.98) .005 MAX. (.127) .208(5.28) .194(4.93) .060(1.52) .030(0.76) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current SM4933A SM4934A 50 100 35 70 50 100 SM4935A 200 140 200 SM4936A SM4937A UNITS V 400 600 V 280 420 V 400 600 See Fig. 2 Peak Forward Surge Current, 8.3 ms single half sine-wave 1.0 A superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 1.0A Maximum DC Reverse Current Ta=25 C 30 1.3 5.0 A V µA 100 200 15 -65 +175 µA nS at Rated DC Blocking Voltage Ta=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: 1. Reverse Recovery Time test condition:IF=1.0A, VR=30V. 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 236 pF C RATING AND CHARACTERISTIC CURVES (SM4933A THRU SM4937A) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE AVERAGE FORWARD CURRENT,(A) CHARACTERISTICS 10 3.0 1.0 1.2 1.0 0.8 Single Phase 0.6 Half Wave 60Hz Resistive Or Inductive Load 0.4 0.2 0 0 20 40 60 Tj=25 C 0.1 .6 .8 1.0 1.2 1.4 1.6 1.8 2.0 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 10K 2W 115Va 60Hz 100 120 140 160 180 200 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 1 8 2 7 6 C P CLARE HPG1002 3 30 Ω/50W NON-INDUCTIVE R1 3Ω 25W UNIT UNDER TEST 4 5 1 AMP SLO-BLO FUSE 30Vdc CONSTANT VOLTAGE SUPPLY C1 1.0µF 300V A R2 1Ω /10W NONINDUCTIVE 1.0Adc FROM CONSTANT VOLTAGE SUPPLY RIPPLE=3mVrms MAX. +10 C 0 IFM 1.0 i(t) di/dt=50A/µS trr 0 IRM(REC) 2.0 40 30 Sine Wave 20 JEDEC method 10 0 5 50 10 100 NUMBER OF CYCLES AT 60Hz Zout 11/2ΩMAX. DC To 2KHz FIG.5-TYPICAL JUNCTION CAPACITANCE 35 FOR RECTIFIER 30 25 20 15 10 5 0 1cm 8.3ms Single Half Tj=25 C 1 R2- TEN 1W 10 Ω1% CARBON CORE IN PARALLEL TA= 25 50 C1 1.0µF 300V MINIMIZE ALL LEAD LENGTHS A-TEKTRONIX 545A. K PLUG IN PRE AMP P6000 PROBE OR EQUIVALENT R1- ADJUSTED FOR 14 BETWEEN POINT 2 OF RELAY AND RECTIFIER INDUCTIVE=3.8 µH PEAK FORWARD SURGE CURRENT,(A) .01 80 AMBIENT TEMPERATURE,( C) Pulse Width 300us 1% Duty Cycle JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) 50 .01 SET TIME BASE FOR .05 .1 .5 1 REVERSE VOLTAGE,(V) 50 / 100ns / cm 237 5 10 50 100