SCDS144A − OCTOBER 2003 − REVISED NOVEMBER 2003
D High-Bandwidth Data Path
D
D
† For additional information regarding the performance
characteristics of the CB3Q family, refer to the TI
application report, CBT-C, CB3T, and CB3Q
Signal-Switch Families, literature number SCDA008.
D
D
D
D
D
RGY PACKAGE
(TOP VIEW)
DBQ, DGV, OR PW PACKAGE
(TOP VIEW)
OE
A1
A2
A3
A4
A5
A6
A7
A8
GND
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
VCC
OE
B1
B2
B3
B4
B5
B6
B7
B8
A1
A2
A3
A4
A5
A6
A7
A8
VCC
D
D
D
1
20
19 OE
18 B1
2
3
17 B2
16 B9
4
5
15 B4
14 B5
6
7
13 B6
12 B7
8
9
10
11
B8
D
D
Undershoot Clamp Diodes
Low Power Consumption
(ICC = 0.7 mA Typical)
VCC Operating Range From 2.3 V to 3.6 V
Data I/Os Support 0 to 5-V Signaling Levels
(0.8-V, 1.2-V, 1.5-V, 1.8-V, 2.5-V, 3.3-V, 5-V)
Control Inputs Can be Driven by TTL or
5-V/3.3-V CMOS Outputs
Ioff Supports Partial-Power-Down Mode
Operation
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Performance Tested Per JESD 22
− 2000-V Human-Body Model
(A114-B, Class II)
− 1000-V Charged-Device Model (C101)
Supports Both Digital and Analog
Applications: Differential Signal Interface,
Memory Interleaving, Bus Isolation,
Low-Distortion Signal Gating
OE
D
D Data and Control Inputs Provide
GND
D
(Up To 500 MHz†)
5-V Tolerant I/Os with Device Powered-Up
or Powered-Down
Low and Flat ON-State Resistance (ron)
Characteristics Over Operating Range
(ron = 4 Ω Typical)
Rail-to-Rail Switching on Data I/O Ports
− 0- to 5-V Switching With 3.3-V VCC
− 0- to 3.3-V Switching With 2.5-V VCC
Bidirectional Data Flow, With Near-Zero
Propagation Delay
Low Input/Output Capacitance Minimizes
Loading and Signal Distortion
(Cio(OFF) = 4 pF Typical)
Fast Switching Frequency
(fOE = 20 MHz Max)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2003, Texas Instruments Incorporated
!"#$%&" ' ()##*& %' "! +),-(%&" .%&*
#".)(&' ("!"#$ &" '+*(!(%&"' +*# &/* &*#$' "! *0%' '&#)$*&'
'&%.%#. 1%##%&2 #".)(&" +#"(*''3 ."*' "& *(*''%#-2 (-).*
&*'&3 "! %-- +%#%$*&*#'
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCDS144A − OCTOBER 2003 − REVISED NOVEMBER 2003
description/ordering information
The SN74CB3Q3345 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage
of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance
allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The
device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data
bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q3345 provides an optimized
interface solution ideally suited for broadband communications, networking, and data-intensive computing
systems.
The SN74CB3Q3384A is organized as an 8-bit bus switch with two output-enable (OE, OE) inputs. When OE
is high or OE is low, the bus switch is ON, and the A port is connected to the B port, allowing bidirectional data
flow between ports. When OE is low and OE is high, the bus switch is OFF, and a high-impedance state exists
between the A and B ports.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging
current backflow through the device when it is powered down. The device has isolation during power off.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup
resistor and OE should be tied to GND through a pulldown resistor; the minimum value of the resistor is
determined by the current-sinking/current-sourcing capability of the driver.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
PACKAGE†
TA
TOP-SIDE
MARKING
QFN − RGY
Tape and reel
SN74CB3Q3345RGYR
BU345
SSOP (QSOP) − DBQ
Tape and reel
SN74CB3Q3345DBQR
CB3Q3345
Tube
SN74CB3Q3345PW
Tape and reel
SN74CB3Q3345PWR
−40°C
−40
C to 85
85°C
C
TSSOP − PW
BU345
TVSOP − DGV
Tape and reel
SN74CB3Q3345DGVR
BU345
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
FUNCTION TABLE
INPUTS
OE
OE
INPUT/OUTPUT
A
FUNCTION
H
X
B
A port = B port
X
L
B
A port = B port
L
H
Z
Disconnect
logic diagram (positive logic)
2
18
A1
A8
B1
SW
9
11
SW
1
OE
OE
2
19
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
B8
SCDS144A − OCTOBER 2003 − REVISED NOVEMBER 2003
simplified schematic, each FET switch (SW)
A
B
VCC
Charge
Pump
EN†
† EN is the internal enable signal applied to the switch.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)‡
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 4.6 V
Control input voltage range, VIN (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Switch I/O voltage range, VI/O (see Notes 1, 2, and 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V
Control input clamp current, IIK (VIN < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
I/O port clamp current, II/OK (VI/O < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
ON-state switch current, II/O (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±64 mA
Continuous current through VCC or GND terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 5): DBQ package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68°C/W
(see Note 5): DGV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92°C/W
(see Note 5): PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83°C/W
(see Note 6): RGY package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
‡ Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltages are with respect to ground unless otherwise specified.
2. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
3. VI and VO are used to denote specific conditions for VI/O.
4. II and IO are used to denote specific conditions for II/O.
5. The package thermal impedance is calculated in accordance with JESD 51-7.
6. The package thermal impedance is calculated in accordance with JESD 51-5.
recommended operating conditions (see Note 7)
VCC
Supply voltage
VIH
High-level control input voltage
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VIL
Low-level control input voltage
VCC = 2.3 V to 2.7 V
VCC = 2.7 V to 3.6 V
VI/O
TA
Data input/output voltage
Operating free-air temperature
MIN
MAX
2.3
3.6
UNIT
1.7
5.5
2
5.5
0
0.7
0
0.8
0
5.5
V
−40
85
°C
V
V
V
NOTE 7: All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCDS144A − OCTOBER 2003 − REVISED NOVEMBER 2003
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
VIK
IIN
TEST CONDITIONS
MIN
VCC = 3.6 V,
VCC = 3.6 V,
II = −18 mA
VIN = 0 to 5.5 V
IOZ‡
VCC = 3.6 V,
VO = 0 to 5.5 V,
VI = 0,
Switch OFF,
VIN = VCC or GND
Ioff
VCC = 0,
VI = 0
ICC
VCC = 3.6 V,
VO = 0 to 5.5 V,
II/O = 0,
Switch ON or OFF,
Control inputs
∆ICC§
Control inputs
ICCD¶
Per control
input
VCC = 3.6 V,
One input at 3 V,
VCC = 3.6 V,
A and B ports open,
Control input switching at 50% duty cycle
Cin
Control inputs
VCC = 3.3 V,
VIN = VCC or GND
TYP†
0.7
Other inputs at VCC or GND
MAX
UNIT
−1.8
V
±1
µA
±1
µA
1
µA
2
mA
30
VIN = 5.5 V, 3.3 V, or 0
Switch OFF,
VI/O = 5.5 V, 3.3 V, or 0
VIN = VCC or GND,
0.13
0.14
2.5
3.5
pF
3.5
5
pF
pF
Cio(OFF)
VCC = 3.3 V,
Cio(ON)
VCC = 3.3 V,
Switch ON,
VIN = VCC or GND,
VI/O = 5.5 V, 3.3 V, or 0
9
11.5
VCC = 2.3 V,
TYP at VCC = 2.5 V
VI = 0,
VI = 1.7 V,
IO = 30 mA
IO = −15 mA
4
8
4.5
9
VCC = 3 V
VI = 0,
VI = 2.4 V,
IO = 30 mA
IO = −15 mA
4
6
4.5
8
ron#
µA
mA/
MHz
Ω
VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins.
† All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.
‡ For I/O ports, the parameter IOZ includes the input leakage current.
§ This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.
¶ This parameter specifies the dynamic power-supply current associated with the operating frequency of a single control input (see Figure 2).
# Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by
the lower of the voltages of the two (A or B) terminals.
switching characteristics over recommended operating free-air temperature range (unless
otherwise noted) (see Figure 3)
VCC = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
FROM
(INPUT)
TO
(OUTPUT)
fOE or fOE||
tpdk
OE or OE
A or B
10
20
MHz
A or B
B or A
0.12
0.2
ns
ten
OE or OE
A or B
6.5
ns
PARAMETER
MIN
1.5
MAX
7.7
MIN
1.5
UNIT
MAX
tdis
A or B
1
6.9
1
6.8
ns
OE or OE
|| Maximum switching frequency for control input (VO > VCC, VI = 5 V, RL ≥ 1 MΩ, CL = 0)
k The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance,
when driven by an ideal voltage source (zero output impedance).
4
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCDS144A − OCTOBER 2003 − REVISED NOVEMBER 2003
TYPICAL ron
vs
VI
ron − ON-State Resistance − W
16
VCC = 3.3 V
TA = 25°C
IO = −15 mA
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
VI − V
Figure 1. Typical ron vs VI, VCC = 3.3 V and IO = −15 mA
TYPICAL ICC
vs
OE or OE SWITCHING FREQUENCY
12
VCC = 3.3 V
TA = 25 °C
A and B ports Open
ICC − mA
10
8
6
4
One OE or OE Switching
2
0
0
2
4
6
8
10
12
14
16
18
20
OE or OE Switching Frequency − MHz
Figure 2. Typical ICC vs OE or OE Switching Frequency, VCC = 3.3 V
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
SCDS144A − OCTOBER 2003 − REVISED NOVEMBER 2003
PARAMETER MEASUREMENT INFORMATION
VCC
Input Generator
VIN
50 Ω
50 Ω
VG1
TEST CIRCUIT
DUT
Input Generator
VI
S1
RL
VO
50 Ω
VG2
CL
(see Note A)
RL
TEST
VCC
S1
RL
VI
CL
tpd(s)
2.5 V ± 0.2 V
3.3 V ± 0.3 V
Open
Open
500 Ω
500 Ω
VCC or GND
VCC or GND
30 pF
50 pF
tPLZ/tPZL
2.5 V ± 0.2 V
3.3 V ± 0.3 V
2 × VCC
2 × VCC
500 Ω
500 Ω
GND
GND
30 pF
50 pF
0.15 V
0.3 V
tPHZ/tPZH
2.5 V ± 0.2 V
3.3 V ± 0.3 V
GND
GND
500 Ω
500 Ω
VCC
VCC
30 pF
50 pF
0.15 V
0.3 V
Output
Control
(VIN)
V∆
VCC
VCC/2
VCC
VCC/2
0V
tPLH
VOH
Output
VCC/2
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
tPLZ
VCC
VCC/2
tPZH
tPHL
VCC/2
VOL
Output
Waveform 2
S1 at GND
(see Note B)
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES (tpd(s))
VCC/2
0V
tPZL
VCC/2
Open
GND
50 Ω
Output
Control
(VIN)
2 × VCC
VOL + V∆
VOL
tPHZ
VCC/2
VOH − V∆
VOH
0V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns.
D. The outputs are measured one at a time with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd(s). The tpd propagation delay is the calculated RC time constant of the typical ON-state
resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance).
H. All parameters and waveforms are not applicable to all devices.
Figure 3. Test Circuit and Voltage Waveforms
6
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MPDS006C – FEBRUARY 1996 – REVISED AUGUST 2000
DGV (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
24 PINS SHOWN
0,40
0,23
0,13
24
13
0,07 M
0,16 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
0°–8°
1
0,75
0,50
12
A
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,08
14
16
20
24
38
48
56
A MAX
3,70
3,70
5,10
5,10
7,90
9,80
11,40
A MIN
3,50
3,50
4,90
4,90
7,70
9,60
11,20
DIM
4073251/E 08/00
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion, not to exceed 0,15 per side.
Falls within JEDEC: 24/48 Pins – MO-153
14/16/20/56 Pins – MO-194
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MSOI004E JANUARY 1995 – REVISED MAY 2002
DBQ (R–PDSO–G**)
PLASTIC SMALL–OUTLINE PACKAGE
0.012 (0,30)
0.008 (0,20)
0.025 (0,64)
0.005 (0,13)
13
24
0.244 (6,20)
0.228 (5,80)
0.157 (3,99)
0.150 (3,81)
0.008 (0,20) NOM
Gauge Plane
1
12
0.010 (0,25)
A
0°–8°
0.035 (0,89)
0.016 (0,40)
0.069 (1,75) MAX
Seating Plane
0.010 (0,25)
0.004 (0,10)
0.004 (0,10)
PINS **
16
20
24
28
A MAX
0.197
(5,00)
0.344
(8,74)
0.344
(8,74)
0.394
(10,01)
A MIN
0.189
(4,80)
0.337
(8,56)
0.337
(8,56)
0.386
(9,80)
M0–137
VARIATION
AB
AD
AE
AF
DIM
D
4073301/F 02/02
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0.006 (0,15).
D. Falls within JEDEC MO–137.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
MECHANICAL DATA
MTSS001C – JANUARY 1995 – REVISED FEBRUARY 1999
PW (R-PDSO-G**)
PLASTIC SMALL-OUTLINE PACKAGE
14 PINS SHOWN
0,30
0,19
0,65
14
0,10 M
8
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
0,25
1
7
0°– 8°
A
0,75
0,50
Seating Plane
0,15
0,05
1,20 MAX
PINS **
0,10
8
14
16
20
24
28
A MAX
3,10
5,10
5,10
6,60
7,90
9,80
A MIN
2,90
4,90
4,90
6,40
7,70
9,60
DIM
4040064/F 01/97
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion not to exceed 0,15.
Falls within JEDEC MO-153
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Amplifiers
Applications
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2003, Texas Instruments Incorporated