TI SN74AUC1G32YZPR

SCES377I − SEPTEMBER 2001 − REVISED NOVEMBER 2003
D Available in the Texas Instruments
D
D
D
D
D
D
D
D
DBV OR DCK PACKAGE
(TOP VIEW)
NanoStar and NanoFree Packages
Optimized for 1.8-V Operation and Is 3.6-V
I/O Tolerant to Support Mixed-Mode Signal
Operation
Ioff Supports Partial-Power-Down Mode
Operation
Sub 1-V Operable
Max tpd of 2.4 ns at 1.8 V
Low Power Consumption, 10-µA Max ICC
±8-mA Output Drive at 1.8 V
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
ESD Protection Exceeds JESD 22
− 2000-V Human-Body Model (A114-A)
− 200-V Machine Model (A115-A)
− 1000-V Charged-Device Model (C101)
A
B
GND
1
5
VCC
4
Y
2
3
YEA, YEP, YZA, OR YZP PACKAGE
(BOTTOM VIEW)
GND
B
A
3 4
Y
2
1 5
VCC
description/ordering information
This single 2-input positive-OR gate is operational at 0.8-V to 2.7-V VCC, but is designed specifically for 1.65-V
to 1.95-V VCC operation.
The SN74AUC1G32 performs the Boolean function Y + A ) B or Y + A • B in positive logic.
NanoStar and NanoFree package technology is a major breakthrough in IC packaging concepts, using the
die as the package.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
PACKAGE†
TA
NanoStar − WCSP (DSBGA)
0.17-mm Small Bump − YEA
SN74AUC1G32YEAR
NanoFree − WCSP (DSBGA)
0.17-mm Small Bump − YZA (Pb-free)
−40°C to 85°C
NanoStar − WCSP (DSBGA)
0.23-mm Large Bump − YEP
TOP-SIDE
MARKING‡
SN74AUC1G32YZAR
Tape and reel
_ _ _UG_
SN74AUC1G32YEPR
NanoFree − WCSP (DSBGA)
0.23-mm Large Bump − YZP (Pb-free)
SN74AUC1G32YZPR
SOT (SOT-23) − DBV
Tape and reel
SN74AUC1G32DBVR
U32_
SOT (SC-70) − DCK
Tape and reel
SN74AUC1G32DCKR
UG_
† Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
‡ DBV/DCK: The actual top-side marking has one additional character that designates the assembly/test site.
YEA/YZA, YEP/YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code,
and one following character to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition
(1 = SnPb, • = Pb-free).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
NanoStar and NanoFree are trademarks of Texas Instruments.
Copyright  2003, Texas Instruments Incorporated
!" #!$% &"'
&! #" #" (" " ") !"
&& *+' &! #", &" ""%+ %!&"
", %% #""'
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
1
SCES377I − SEPTEMBER 2001 − REVISED NOVEMBER 2003
description/ordering information (continued)
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down.
For more information about AUC Little Logic devices, please refer to the TI application report, Applications of
Texas Instruments AUC Sub-1-V Little Logic Devices, literature number SCEA027.
FUNCTION TABLE
INPUTS
A
B
OUTPUT
Y
H
X
H
X
H
H
L
L
L
logic diagram (positive logic)
A
B
1
2
4
Y
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 3.6 V
Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 3.6 V
Voltage range applied to any output in the high-impedance or power-off state, VO
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 3.6 V
Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V
Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA
Continuous output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA
Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±100 mA
Package thermal impedance, θJA (see Note 2): DBV package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206°C/W
DCK package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252°C/W
YEA/YZA package . . . . . . . . . . . . . . . . . . . . . . . . . . . 154°C/W
YEP/YZP package . . . . . . . . . . . . . . . . . . . . . . . . . . . 132°C/W
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
† Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed.
2. The package thermal impedance is calculated in accordance with JESD 51-7.
2
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
SCES377I − SEPTEMBER 2001 − REVISED NOVEMBER 2003
recommended operating conditions (see Note 3)
VCC
VIH
MIN
MAX
0.8
2.7
Supply voltage
VCC = 0.8 V
VCC = 1.1 V to 1.95 V
High-level input voltage
VI
VO
V
1.7
0
0.35 × VCC
VCC = 1.1 V to 1.95 V
VCC = 2.3 V to 2.7 V
Low-level input voltage
Output voltage
0
3.6
V
0
VCC
−0.7
V
VCC = 0.8 V
VCC = 1.1 V
High-level output current
IOL
Low-level output current
∆t/∆v
V
0.7
Input voltage
IOH
V
VCC
0.65 × VCC
VCC = 2.3 V to 2.7 V
VCC = 0.8 V
VIL
UNIT
−3
VCC = 1.4 V
VCC = 1.65 V
−5
VCC = 2.3 V
VCC = 0.8 V
−9
mA
−8
0.7
VCC = 1.1 V
VCC = 1.4 V
3
VCC = 1.65 V
VCC = 2.3 V
8
5
mA
9
Input transition rise or fall rate
20
ns/V
TA
Operating free-air temperature
−40
85
°C
NOTE 3: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, literature number SCBA004.
electrical characteristics over recommended operating free-air temperature range (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
IOH = −100 µA
IOH = −0.7 mA
VOH
VOL
II
Ioff
ICC
Ci
A or B input
VCC
0.8 V to 2.7 V
MIN
MAX
0.55
IOH = −3 mA
IOH = −5 mA
1.1 V
0.8
1.4 V
1
IOH = −8 mA
IOH = −9 mA
1.65 V
1.2
2.3 V
1.8
IOL = 100 µA
IOL = 0.7 mA
0.8 V to 2.7 V
V
0.2
0.25
IOL = 3 mA
IOL = 5 mA
1.1 V
0.3
1.4 V
0.4
IOL = 8 mA
IOL = 9 mA
1.65 V
0.45
2.3 V
0.6
VI = VCC or GND
VI or VO = 2.7 V
VI = VCC or GND,
VI = VCC or GND
IO = 0
UNIT
VCC−0.1
0.8 V
0.8 V
TYP†
V
0 to 2.7 V
±5
µA
0
±10
µA
10
µA
0.8 V to 2.7 V
2.5 V
4
pF
† All typical values are at TA = 25°C.
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
3
SCES377I − SEPTEMBER 2001 − REVISED NOVEMBER 2003
switching characteristics over recommended operating free-air temperature range, CL = 15 pF
(unless otherwise noted) (see Figure 1)
PARAMETER
tpd
VCC = 1.2 V
± 0.1 V
VCC = 1.5 V
± 0.1 V
VCC = 1.8 V
± 0.15 V
VCC = 2.5 V
± 0.2 V
FROM
(INPUT)
TO
(OUTPUT)
VCC = 0.8 V
TYP
MIN
MAX
MIN
MAX
MIN
TYP
MAX
MIN
MAX
A or B
Y
4.8
1
3.5
0.6
2.3
†
†
†
†
†
UNIT
ns
† This information was not available at the time of publication.
switching characteristics over recommended operating free-air temperature range, CL = 30 pF
(unless otherwise noted) (see Figure 1)
PARAMETER
tpd
FROM
(INPUT)
TO
(OUTPUT)
A or B
Y
VCC = 1.8 V
± 0.15 V
VCC = 2.5 V
± 0.2 V
MIN
TYP
MAX
MIN
MAX
0.8
1.4
2.4
0.6
2.1
UNIT
ns
operating characteristics, TA = 25°C
PARAMETER
Cpd
4
Power dissipation
capacitance
TEST
CONDITIONS
f = 10 MHz
VCC = 0.8 V
TYP
14
POST OFFICE BOX 655303
VCC = 1.2 V
TYP
VCC = 1.5 V
TYP
14
• DALLAS, TEXAS 75265
15
VCC = 1.8 V
TYP
15
VCC = 2.5 V
TYP
20
UNIT
pF
SCES377I − SEPTEMBER 2001 − REVISED NOVEMBER 2003
PARAMETER MEASUREMENT INFORMATION
2 × VCC
S1
RL
From Output
Under Test
Open
GND
CL
(see Note A)
RL
VCC
0.8 V
1.2 V ± 0.1 V
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
LOAD CIRCUIT
TEST
S1
tPLH/tPHL
tPLZ/tPZL
tPHZ/tPZH
Open
2 × VCC
GND
CL
RL
15 pF
15 pF
15 pF
15 pF
15 pF
30 pF
30 pF
2 kΩ
2 kΩ
2 kΩ
2 kΩ
2 kΩ
1 kΩ
500 Ω
V∆
0.1 V
0.1 V
0.1 V
0.15 V
0.15 V
0.15 V
0.15 V
VCC
Timing Input
VCC/2
0V
tw
tsu
VCC
VCC/2
Input
th
VCC
VCC/2
VCC/2
Data Input
VCC/2
0V
0V
VOLTAGE WAVEFORMS
PULSE DURATION
VOLTAGE WAVEFORMS
SETUP AND HOLD TIMES
VCC
VCC/2
Input
0V
tPHL
tPLH
VOH
VCC/2
Output
VCC/2
VOL
Output
Waveform 1
S1 at 2 × VCC
(see Note B)
VOH
Output
VCC/2
VCC/2
VCC/2
VOL
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
INVERTING AND NONINVERTING OUTPUTS
VCC/2
0V
tPLZ
tPZL
VCC
VCC/2
Output
Waveform 2
S1 at GND
(see Note B)
VOL + V∆
VOL
tPHZ
tPZH
tPLH
tPHL
VCC
Output
Control
VCC/2
VCC/2
VOH − V∆
VOH
≈0 V
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
LOW- AND HIGH-LEVEL ENABLING
NOTES: A. CL includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, slew rate ≥ 1 V/ns.
D. The outputs are measured one at a time with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.
Figure 1. Load Circuit and Voltage Waveforms
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
5
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
SN74AUC1G32DBVR
ACTIVE
SOT-23
DBV
5
3000 Green (RoHS &
no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
SN74AUC1G32DCKR
ACTIVE
SC70
DCK
5
3000
Pb-Free
(RoHS)
CU NIPDAU
Level-1-260C-UNLIM
SN74AUC1G32YEAR
ACTIVE
WCSP
YEA
5
3000
TBD
SNPB
Level-1-260C-UNLIM
SN74AUC1G32YEPR
ACTIVE
WCSP
YEP
5
3000
TBD
SNPB
Level-1-260C-UNLIM
SN74AUC1G32YZAR
ACTIVE
WCSP
YZA
5
3000
TBD
Call TI
Call TI
SN74AUC1G32YZPR
ACTIVE
WCSP
YZP
5
3000
Pb-Free
(RoHS)
SNAGCU
Lead/Ball Finish
MSL Peak Temp (3)
Level-1-260C-UNLIM
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
MECHANICAL DATA
MPDS025C – FEBRUARY 1997 – REVISED FEBRUARY 2002
DCK (R-PDSO-G5)
PLASTIC SMALL-OUTLINE PACKAGE
0,30
0,15
0,65
5
0,10 M
4
1,40
1,10
1
0,13 NOM
2,40
1,80
3
Gage Plane
2,15
1,85
0,15
0°–8°
0,46
0,26
Seating Plane
1,10
0,80
0,10
0,00
0,10
4093553-2/D 01/02
NOTES: A.
B.
C.
D.
All linear dimensions are in millimeters.
This drawing is subject to change without notice.
Body dimensions do not include mold flash or protrusion.
Falls within JEDEC MO-203
POST OFFICE BOX 655303
• DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2005, Texas Instruments Incorporated