High Speed, Dual Channel Power MOSFET Drivers Features General Description # Industry standard driver replacement # Improved response times # Matched rise and fall times # Reduced clock skew # Low output impedance # Low input capacitance # High noise immunity # Improved clocking rate # Low supply current # Wide operating voltage range The EL7202C/EL7212C/EL7222C ICs are matched dual-drivers ICs that improve the operation of the industry standard DS0026 clock drivers. The Elantec Versions are very high speed drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads. The high speed performance is achieved by means of a proprietary ‘‘Turbo-Driver’’ circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques. Applications # # # # # # # # Clock/line drivers CCD Drivers Ultra-sound transducer drivers Power MOSFET drivers Switch mode power supplies Class D switching amplifiers Ultrasonic and RF generators Pulsed circuits EL7202C/EL7212C/EL7222C EL7202C/7212C/7222C Connection Diagrams EL7222C EL7212C Ordering Information 7202 – 2 Part No. Temp. Range Pkg. Outline Ý Inverting Drivers 7202 – 1 Complementary Drivers EL7202CN b 40§ C to a 85§ C 8-Pin P-DIP MDP0031 EL7202CS b 40§ C to a 85§ C 8-Pin SO MDP0027 EL7202C EL7212CN b 40§ C to a 85§ C 8-Pin P-DIP MDP0031 EL7212CS b 40§ C to a 85§ C 8-Pin SO MDP0027 EL7222CN b 40§ C to a 85§ C 8-Pin P-DIP MDP0031 EL7222CS b 40§ C to a 85§ C 8-Pin SO MDP0027 Manufactured under U.S. Patent Nos. 5,334,883, Ý5,341,047 Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a ‘‘controlled document’’. Current revisions, if any, to these specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation. © 1994 Elantec, Inc. January 1996 Rev. B 7202 – 3 Non-Inverting Drivers EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers Absolute Maximum Ratings Supply (V a to Gnd) Input Pins Combined Peak Output Current Storage Temperature Range Ambient Operating Temperature 125§ C Operating Junction Temperature Power Dissipation SOIC PDIP 16.5V b 0.3V to a 0.3V above V a 4A b 65§ C to a 150§ C b 40§ C to a 85§ C 570 mW 1050 mW Important Note: All parameters having Min/Max specifications are guaranteed. The Test Level column indicates the specific device testing actually performed during production and Quality inspection. Elantec performs most electrical tests using modern high-speed automatic test equipment, specifically the LTX77 Series system. Unless otherwise noted, all tests are pulsed tests, therefore TJ e TC e TA. Test Level I II III IV V Test Procedure 100% production tested and QA sample tested per QA test plan QCX0002. 100% production tested at TA e 25§ C and QA sample tested at TA e 25§ C , TMAX and TMIN per QA test plan QCX0002. QA sample tested per QA test plan QCX0002. Parameter is guaranteed (but not tested) by Design and Characterization Data. Parameter is typical value at TA e 25§ C for information purposes only. DC Electrical Characteristics TA e 25§ C, V e 15V unless otherwise specified Parameter Description Test Conditions Min Typ Test Level Units I V 10 I mA 0.8 I V Max Input VIH Logic ‘‘1’’ Input Voltage IIH Logic ‘‘1’’ Input Current VIL Logic ‘‘0’’ Input Voltage IIL Logic ‘‘0’’ Input Current VHVS Input Hysteresis 2.4 @Va 0.1 @ 0V 0.1 10 0.3 I mA V V Output ROH Pull-Up Resistance IOUT e b100 mA 3 6 I X ROL Pull-Down Resistance IOUT e a 100 mA 4 6 I X IPK Peak Output Current Source Sink 2 2 IV A IDC Continuous Output Current Source/Sink I mA Power Supply Current Inputs High/7202 Inputs High/7212 Inputs High/7222 7.5 2.5 5.0 I I I mA 15 I V 100 IS VS Operating Voltage 4.5 1 2.5 4.5 2 TD is 3.3in Power Supply EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers AC Electrical Characteristics TA e 25§ C, V e 15V unless otherwise specified Parameter Description Test Conditions Min Typ Max CL e 500 pF CL e 1000 pF 7.5 10 20 CL e 500 pF CL e 1000 pF 10 13 20 Test Level Units IV ns IV ns tR tF Rise Time Fall Time tD1 Turn-On Delay Time See Timing Table 18 25 IV ns tD2 Turn-Off Delay Time See Timing Table 20 25 IV ns Timing Table Standard Test Configuration 7202 – 19 7202 – 4 Simplified Schematic 7202 – 5 3 TD is 1.5in Switching Characteristics EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers Typical Performance Curve Max Power/Derating Curves Switch Threshold vs Supply Voltage 7202 – 6 7202 – 7 Input Current vs Voltage Peak Drive vs Supply Voltage 7202 – 8 7202 – 9 Quiescent Supply Current ‘‘ON’’ Resistance vs Supply Voltage 7202 – 10 4 7202 – 11 EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers Typical Performance Curve Ð Contd. Average Supply Current vs Voltage and Frequency Average Supply Current vs Capacitive Load 7202 – 12 7202 – 13 Rise/Fall Time vs Load Rise/Fall Time vs Supply Voltage 7202 – 15 7202 – 14 5 EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers Typical Performance Curve Ð Contd. Propagation Delay vs Supply Voltage Rise/Fall Time vs Temperature 7202 – 16 7202 – 17 Delay vs Temperature 7202 – 18 6 EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers EL7212 Macro Model 7202 – 20 TD is 3.6in **** EL7212 model **** * input * gnd l Vsupply * l l Vout * l l l .subckt M7212 2 3 6 7 V1 12 3 1.6 R1 13 15 1k R2 14 15 5k R5 11 12 100 C1 15 3 43.3 pF D1 14 13 dmod X1 13 11 2 3 comp1 X2 16 12 15 3 comp1 sp 6 7 16 3 spmod sn 7 3 16 3 snmod g1 11 0 13 0 938m .model dmod d .model spmod vswitch ron43 roff42meg von41 voff41.5 .model snmod vswitch ron44 roff42meg von43 voff42 .ends M7212 .subckt comp1 out inp inm vss e1 out vss table À (v(inp) 1v(inm))* 5000Ó 4 (0,0) (3.2,3.2) Rout out vss 10meg Rinp inp vss 10meg Rinm inm vss 10meg .ends comp1 7 EL7202C/EL7212C/EL7222C EL7202C/EL7212C/EL7222C High Speed, Dual Channel Power MOSFET Drivers General Disclaimer Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the circuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement. January 1996 Rev. B WARNING Ð Life Support Policy Elantec, Inc. products are not authorized for and should not be used within Life Support Systems without the specific written consent of Elantec, Inc. Life Support systems are equipment intended to support or sustain life and whose failure to perform when properly used in accordance with instructions provided can be reasonably expected to result in significant personal injury or death. Users contemplating application of Elantec, Inc. products in Life Support Systems are requested to contact Elantec, Inc. factory headquarters to establish suitable terms & conditions for these applications. Elantec, Inc.’s warranty is limited to replacement of defective components and does not cover injury to persons or property or other consequential damages. Elantec, Inc. 1996 Tarob Court Milpitas, CA 95035 Telephone: (408) 945-1323 (800) 333-6314 Fax: (408) 945-9305 European Office: 44-71-482-4596 8 Printed in U.S.A.