EMC EKM6251

Preliminary
eKM6251
U+P RF Mouse Rx Controller
GENERAL DESCRIPTOR
The eKM6251 is standard RF Mouse Receiver (Rx) Controller for USB and PS/2 compatible
interface. It’s receives the RF packet data from RF Rx module (circuits). And decode the RF packet
data and transmitting the data to PC by USB or PS/2 interface. The eKM6251 have internal
EEPROM to storage the Device ID, do not need the external storage device like 93C46. It’s have
built-in RF signal sampling and noise immunity function to improve the RF data decode efficiency.
FEATURE
Operating voltage: 2.5V~5.5V
Built-in regulator to generate 3.3V
Operating frequency: 6.00Mhz
Built-in USB Device Controller and Interface.
Support USB and PS/2 detect mode and compatible interface.
Built-in EEPROM to storage 1 byte Device ID (255 sets)
Built-in RF signal sampling and noise immunity function.
Support a LED to display RF packet receive status and ID set mode.
Using jump connect to set Device ID into default ID.
Support RF monitor pin to check RF packet receive situation.
To match with RF Mouse Tx controller:
EM84100 series
EKM6711 : Optical RF Mouse Tx
Package:
16 pin DIP and NSOP (150mil)
APPLICATION
USB RF Mouse Rx
PS/2 RF Mouse Rx
* This specification are subject to be changed without notice.
1
2002/11/15
Preliminary
eKM6251
U+P RF Mouse Rx Controller
PIN ASSIGNMENT
U1
1
2
3
4
5
6
7
8
RFC1
RFC2
RxLED
RFM
VSS
NC
V3.3
OSCI
RFD
Connect
IDR
NC
D+/DATA
D-/CLK
VDD
OSCO
16
15
14
13
12
11
10
9
eKM6251
PIN DESCRIPTOR
Pin No.
Symbol
I/O
Function
1
RFC1
O
RF module control pin 1 (channel control)
2
RFC2
O
RF module control pin 2 (power down control)
3
RxLED
O
Direct sink LED to display RF packet receive.
4
RFM
O
RF monitor pin, to check RF packet receive situation.
5
VSS
-
Ground
6
NC
-
NC
7
V3.3
O
V3.3 DC voltage output from internal regulator
8
OSCI
I
6.00Mhz ceramic resonator crystal input
9
OSCO
I/O
10
VDD
-
11
D-/CLK
I/O
USB: D- line
PS/2: CLK line (It’s need external USB to PS/2 transfer)
12
D+/DATA
I/O
USB: D+ line
PS/2: CLK line (It’s need external USB to PS/2 transfer)
13
NC
-
NC
14
IDR
I
ID Reset button, its set device ID to default ID (internal pull high
resistor)
15
CONNECT
I
Connect button, it’s will receive new device ID duration 10
seconds. (internal pull high resistor)
16
RFD
I
RF data input
Output terminal for crystal oscillator
5.0V Power supply
* This specification are subject to be changed without notice.
2
2002/11/15
Preliminary
eKM6251
U+P RF Mouse Rx Controller
ABSOLUTE MAXIMUM RATINGS
Items
Sym.
Condition
Rating
0℃~70℃
Temperature under bias
TOPR
Storage temperature
TSTR
-65℃~150℃
Input voltage
VIN
-0.3V~+6.0V
Output voltage
VO
-0.3V~+6.0V
DC ELECTRICAL CHARACTERISTIC
Parameter
Sym.
Condition
Min. Typ. Max. Unit
* This specification are subject to be changed without notice.
3
2002/11/15
eKM6251
U+P RF Mouse Rx Controller
Preliminary
APPLICATION CIRCUIT
RF Control2(Power Down)
RF Control1(Channel)
R6
RF Data
D15
U10
VCC
R
RxLED
RF Monitor
C7
1uF
1
2
3
4
5
6
7
8
RFC1
RFC2
RxLED
RFM
VSS
NC
V3.3
OSCI
SW8
RFD
Connect
IDR
NC
D+/DATA
D-/CLK
VDD
OSCO
16
15
14
13
12
11
10
9
CONNECT
1 J2
2
ID Reset
USB D+ / DATA
USB D- / CLK
VCC
VCC
C6
10uF
eKM6251
Q5
J6
1
2
3
4
DD+
6.00Mhz
C4
20pF
C5
20pF
USB CONN
VCC
CLK
DATA
1
2
3
6
5
4
PS2/MS
* This specification are subject to be changed without notice.
4
2002/11/15