2N5551 / MMBT5551 MMBT5551 2N5551 C E C B TO-92 SOT-23 E B Mark: 3S NPN General Purpose Amplifier This device is designed for general purpose high voltage amplifiers and gas discharge display driving. Sourced from Process 16. Absolute Maximum Ratings* Symbol TA = 25°C unless otherwise noted Parameter Value Units V VCEO Collector-Emitter Voltage 160 VCBO Collector-Base Voltage 180 V VEBO Emitter-Base Voltage 6.0 V IC Collector Current - Continuous 600 mA TJ, Tstg Operating and Storage Junction Temperature Range -55 to +150 °C *These ratings are limiting values above which the serviceability of any semiconductor device may be impaired. NOTES: 1) These ratings are based on a maximum junction temperature of 150 degrees C. 2) These are steady state limits. The factory should be consulted on applications involving pulsed or low duty cycle operations. Thermal Characteristics Symbol PD TA = 25°C unless otherwise noted Characteristic RθJC Total Device Dissipation Derate above 25°C Thermal Resistance, Junction to Case RθJA Thermal Resistance, Junction to Ambient Max Units 2N5551 625 5.0 83.3 *MMBT5551 350 2.8 200 357 mW mW/°C °C/W °C/W *Device mounted on FR-4 PCB 1.6" X 1.6" X 0.06." 2000 Fairchild Semiconductor International 2N5551/MMBT5551 Rev A (continued) Electrical Characteristics Symbol TA = 25°C unless otherwise noted Parameter Test Conditions Min Max Units OFF CHARACTERISTICS V(BR)CEO Collector-Emitter Sustaining Voltage* IC = 1.0 mA, IB = 0 160 V V(BR)CBO Collector-Base Breakdown Voltage IC = 100 µA, IE = 0 180 V V(BR)EBO Emitter-Base Breakdown Voltage IE = 10 µA, IC = 0 6.0 V ICBO Collector Cutoff Current IEBO Emitter Cutoff Current VCB = 120 V, IE = 0, VCB = 120 V, IE = 0, TA = 100°C VEB = 4.0 V, IC = 0 50 50 50 nA µA nA ON CHARACTERISTICS hFE DC Current Gain VCE(sat) Collector-Emitter Saturation Voltage VBE(sat) Base-Emitter Saturation Voltage IC = 1.0 mA, VCE = 5.0 V IC = 10 mA, VCE = 5.0 V IC = 50 mA, VCE = 5.0 V IC = 10 mA, IB = 1.0 mA IC = 50 mA, IB = 5.0 mA IC = 10 mA, IB = 1.0 mA IC = 50 mA, IB = 5.0 mA 80 80 30 IC = 10 mA, VCE = 10 V, f = 100 MHz VCB = 10 V, IE = 0, f = 1.0 MHz VBE = 0.5 V, IC = 0, f = 1.0 MHz IC = 1.0 mA, VCE = 10 V, f = 1.0 kHz IC = 250 µA, VCE = 5.0 V, RS=1.0 kΩ, f=10 Hz to 15.7 kHz 100 250 0.15 0.20 1.0 1.0 V V V V 300 MHz 6.0 pF 20 pF SMALL SIGNAL CHARACTERISTICS fT Current Gain - Bandwidth Product Cobo Output Capacitance Cibo Input Capacitance hfe Small-Signal Current Gain NF Noise Figure 50 250 8.0 dB *Pulse Test: Pulse Width ≤ 300 µs, Duty Cycle ≤ 2.0% Spice Model NPN (Is=2.511f Xti=3 Eg=1.11 Vaf=100 Bf=242.6 Ne=1.249 Ise=2.511f Ikf=.3458 Xtb=1.5 Br=3.197 Nc=2 Isc=0 Ikr=0 Rc=1 Cjc=4.883p Mjc=.3047 Vjc=.75 Fc=.5 Cje=18.79p Mje=.3416 Vje=.75 Tr=1.202n Tf=560p Itf=50m Vtf=5 Xtf=8 Rb=10) 2N5551 / MMBT5551 NPN General Purpose Amplifier (continued) hFE - TYPICAL PULSED CURRENT GAIN Typical Pulsed Current Gain vs Collector Current 250 Vce = 5V 125 °C 200 150 25 °C 100 - 40 °C 50 0 0.1 0.2 0.5 1 2 5 10 20 50 100 I C - COLLECTOR CURRENT (mA) VCESAT- COLLECTOR EMITTER VOLTAGE (V) Typical Characteristics Collector-Emitter Saturation Voltage vs Collector Current 0.5 0.4 β = 10 0.3 25 °C 0.2 125 ºC 0.1 - 40 ºC 0 1 10 100 I C - COLLECTOR CURRENT (mA) 200 Base-Emitter Saturation Voltage vs Collector Current 1 β = 10 0.8 - 40 ºC 25 °C 0.6 125 ºC 0.4 0.2 0 1 10 100 I C - COLLECTOR CURRENT (mA) 200 VBEON - BASE EMITTER ON VOLTAGE (V) VBESAT- BASE EMITTER VOLTAGE (V) P 16 Base Emitter ON Voltage vs Collector Current 1 25 °C 0.6 125 ºC 0.4 10 1 25 50 75 100 T A - AMBIENT TEMPERATURE ( º C) P 125 BV CER - BREAKDOWN VOLTAGE (V) I CBO- COLLECTOR CURRENT (nA) VCB = 100V VCE = 5V 0.2 0 0.1 1 10 I C - COLLECTOR CURRENT (mA) 100 200 Collector-Emitter Breakdown Voltage with Resistance Between Emitter-Base Collector-Cutoff Current vs. Ambient Temperature 50 - 40 ºC 0.8 260 I C = 1.0 mA 240 220 200 180 160 0.1 1 10 RESISTANCE (k Ω) 100 1000 2N5551 / MMBT5551 NPN General Purpose Amplifier (continued) Typical Characteristics Input and Output Capacitance vs Reverse Voltage 30 25 20 15 10 C ib 5 0 0.1 C cb 1 10 100 Small Signal Current Gain vs Collector Current 16 FREG = 20 MHz V CE = 10V 12 8 4 0 1 10 I C - COLLECTOR CURRENT (mA) V CE - COLLECTOR VOLTAGE (V) Power Dissipation vs Ambient Temperature 700 PD - POWER DISSIPATION (mW) CAPACITANCE (pF) f = 1.0 MHz h FE - SMALL SIGNAL CURRENT GAIN (continued) 600 500 TO-92 SOT-23 400 300 200 100 0 0 25 50 75 100 TEMPERATURE ( o C) 125 150 50 2N5551 / MMBT5551 NPN General Purpose Amplifier TO-92 Tape and Reel Data and Package Dimensions TO-92 Packaging Configuration: Figure 1.0 TAPE and REEL OPTION FSCINT Label sample FAIRCHILD SEMICONDUCTOR CORPORATION LOT: NSID: D/C1: CBVK741B019 QTY: PN2222N See Fig 2.0 for various Reeling Styles HTB:B 10000 SPEC: D9842 SPEC REV: FSCINT Label B2 QA REV: 5 Reels per Intermediate Box (FSCINT) Customized Label F63TNR Label sample LOT: CBVK741B019 FSID: PN222N D/C1: D9842 D/C2: F63TNR Label QTY: 2000 SPEC: QTY1: QTY2: SPEC REV: CPN: N/F: F Customized Label (F63TNR)3 375mm x 267mm x 375mm Intermediate Box TO-92 TNR/AMMO PACKING INFROMATION Packing Style Quantity EOL code Reel A 2,000 D26Z E 2,000 D27Z Ammo M 2,000 D74Z P 2,000 D75Z AMMO PACK OPTION See Fig 3.0 for 2 Ammo Pack Options FSCINT Label Unit weight = 0.22 gm Reel weight with components = 1.04 kg Ammo weight with components = 1.02 kg Max quantity per intermediate box = 10,000 units 327mm x 158mm x 135mm Immediate Box Customized Label (TO-92) BULK PACKING INFORMATION EOL CODE DESCRIPTION 5 Ammo boxes per Intermediate Box Customized Label F63TNR Label 333mm x 231mm x 183mm Intermediate Box BULK OPTION LEADCLIP DIMENSION QUANTITY J18Z TO-18 OPTION STD NO LEAD CLIP 2.0 K / BOX J05Z TO-5 OPTION STD NO LEAD CLIP 1.5 K / BOX NO EOL CODE TO-92 STANDARD STRAIGHT NO LEADCLIP 2.0 K / BOX See Bulk Packing Information table Anti-static Bubble Sheets FSCINT Label 2000 units per EO70 box for std option 114mm x 102mm x 51mm Immediate Box 5 EO70 boxes per intermediate Box 530mm x 130mm x 83mm Intermediate box Customized Label FSCINT Label 10,000 units maximum per intermediate box for std option September 1999, Rev. B TO-92 Tape and Reel Data and Package Dimensions, continued TO-92 Reeling Style Configuration: Figure 2.0 Machine Option “A” (H) Machine Option “E” (J) Style “A”, D26Z, D70Z (s/h) Style “E”, D27Z, D71Z (s/h) TO-92 Radial Ammo Packaging Configuration: Figure 3.0 FIRST WIRE OFF IS COLLECTOR ADHESIVE TAPE IS ON THE TOP SIDE FLAT OF TRANSISTOR IS ON TOP ORDER STYLE D74Z (M) FIRST WIRE OFF IS EMITTER (ON PKG. 92) ADHESIVE TAPE IS ON BOTTOM SIDE FLAT OF TRANSISTOR IS ON BOTTOM FIRST WIRE OFF IS EMITTER ADHESIVE TAPE IS ON THE TOP SIDE FLAT OF TRANSISTOR IS ON BOTTOM ORDER STYLE D75Z (P) FIRST WIRE OFF IS COLLECTOR (ON PKG. 92) ADHESIVE TAPE IS ON BOTTOM SIDE FLAT OF TRANSISTOR IS ON TOP September 1999, Rev. B TO-92 Tape and Reel Data and Package Dimensions, continued TO-92 Tape and Reel Taping Dimension Configuration: Figure 4.0 Hd P Pd b Ha W1 d L H1 HO L1 S WO t W2 W t1 P1 F1 DO P2 PO User Direction of Feed TO-92 Reel Configuration: Figure 5.0 ITEM DESCRIPTION SYMBOL DIMENSION Base of Package to Lead Bend b 0.098 (max) Component Height Ha 0.928 (+/- 0.025) Lead Clinch Height HO 0.630 (+/- 0.020) Component Base Height H1 0.748 (+/- 0.020) Component Alignment ( side/side ) Pd 0.040 (max) Component Alignment ( front/back ) Hd 0.031 (max) Component Pitch P 0.500 (+/- 0.020) Feed Hole Pitch PO 0.500 (+/- 0.008) Hole Center to First Lead P1 0.150 (+0.009, -0.010) Hole Center to Component Center P2 0.247 (+/- 0.007) Lead Spread F1/F2 0.104 (+/- 0 .010) Lead Thickness d 0.018 (+0.002, -0.003) Cut Lead Length L 0.429 (max) Taped Lead Length L1 0.209 (+0.051, -0.052) Taped Lead Thickness t 0.032 (+/- 0.006) Carrier Tape Thickness t1 0.021 (+/- 0.006) Carrier Tape Width W 0.708 (+0.020, -0.019) Hold - down Tape Width WO 0.236 (+/- 0.012) Hold - down Tape position W1 0.035 (max) Feed Hole Position W2 0.360 (+/- 0.025) Sprocket Hole Diameter DO 0.157 (+0.008, -0.007) Lead Spring Out S 0.004 (max) Note : All dimensions are in inches. ELECT ROSTATIC SEN SITIVE D EVICES D4 D1 D2 F63TNR Label ITEM DESCRIPTION SYSMBOL MINIMUM MAXIMUM Reel Diameter D1 13.975 14.025 Arbor Hole Diameter (Standard) D2 1.160 1.200 D2 0.650 0.700 Customized Label (Small Hole) W1 Core Diameter D3 3.100 3.300 Hub Recess Inner Diameter D4 2.700 3.100 Hub Recess Depth W1 0.370 0.570 Flange to Flange Inner Width W2 1.630 Hub to Hub Center Width W3 1.690 2.090 W3 W2 Note: All dimensions are inches D3 July 1999, Rev. A TO-92 Tape and Reel Data and Package Dimensions TO-92 (FS PKG Code 92, 94, 96) 1:1 Scale 1:1 on letter size paper Dimensions shown below are in: inches [millimeters] Part Weight per unit (gram): 0.1977 January 2000, Rev. B SOT-23 Tape and Reel Data and Package Dimensions SOT-23 Packaging Configuration: Figure 1.0 Customized Label Packaging Description: SOT-23 parts are shipped in tape. The carrier tape is made from a dissipative (carbon filled) polycarbonate resin. The cover tape is a multilayer film (Heat Activated Adhesive in nature) primarily composed of polyester film, adhesive layer, sealant, and anti-static sprayed agent. These reeled parts in standard option are shipped with 3,000 units per 7" or 177cm diameter reel. The reels are dark blue in color and is made of polystyrene plastic (antistatic coated). Other option comes in 10,000 units per 13" or 330cm diameter reel. This and some other options are described in the Packaging Information table. Antistatic Cover Tape Human Readable Label These full reels are individually labeled and placed inside a standard intermediate made of recyclable corrugated brown paper with a Fairchil d logo printing. One pizza box contains eight reels maximum. And these intermediate boxes are placed inside a labeled shipping box which comes in different sizes depending on the number of parts shipped. Embossed Carrier Tape 3P 3P 3P 3P SOT-23 Packaging Information Packaging Option Packaging type Qty per Reel/Tube/Bag Standard (no flow code) TNR 3,000 D87Z 7" Dia 13" 187x107x183 343x343x64 Max qty per Box 24,000 30,000 Weight per unit (gm) 0.0082 0.0082 Weight per Reel (kg) 0.1175 0.4006 Reel Size Box Dimension (mm) SOT-23 Unit Orientation TNR 10,000 343mm x 342mm x 64mm Intermediate box for L87Z Option Human Readable Label Note/Comments Human Readable Label sample H uman readable Label 187mm x 107mm x 183mm Intermediate Box for Standard Option SOT-23 Tape Leader and Trailer Configuration: Figure 2.0 Carrier Tape Cover Tape Components Trailer Tape 300mm minimum or 75 empty poc kets Leader Tape 500mm minimum or 125 empty pockets September 1999, Rev. C SOT-23 Tape and Reel Data and Package Dimensions, continued SOT-23 Embossed Carrier Tape Configuration: Figure 3.0 P0 P2 D0 D1 T E1 W F E2 Wc B0 Tc A0 P1 K0 User Direction of Feed Dimensions are in millimeter Pkg type A0 B0 SOT-23 (8mm) 3.15 +/-0.10 2.77 +/-0.10 W 8.0 +/-0.3 D0 D1 E1 E2 1.55 +/-0.05 1.125 +/-0.125 1.75 +/-0.10 F 6.25 min 3.50 +/-0.05 P1 P0 4.0 +/-0.1 4.0 +/-0.1 K0 T 1.30 +/-0.10 0.228 +/-0.013 Notes: A0, B0, and K0 dimensions are determined with respect to the EIA/Jedec RS-481 rotational and lateral movement requirements (see sketches A, B, and C). Wc 0.06 +/-0.02 0.5mm maximum 20 deg maximum Typical component cavity center line B0 5.2 +/-0.3 Tc 0.5mm maximum 20 deg maximum component rotation Typical component center line Sketch A (Side or Front Sectional View) A0 Component Rotation Sketch C (Top View) Component lateral movement Sketch B (Top View) SOT-23 Reel Configuration: Figure 4.0 Component Rotation W1 Measured at Hub Dim A Max Dim A max See detail AA Dim N 7" Diameter Option B Min Dim C See detail AA W3 13" Diameter Option Dim D min W2 max Measured at Hub DETAIL AA Dimensions are in inches and millimeters Tape Size Reel Option Dim A Dim B Dim C Dim D Dim N Dim W1 Dim W2 Dim W3 (LSL-USL) 8mm 7" Dia 7.00 177.8 0.059 1.5 512 +0.020/-0.008 13 +0.5/-0.2 0.795 20.2 2.165 55 0.331 +0.059/-0.000 8.4 +1.5/0 0.567 14.4 0.311 – 0.429 7.9 – 10.9 8mm 13" Dia 13.00 330 0.059 1.5 512 +0.020/-0.008 13 +0.5/-0.2 0.795 20.2 4.00 100 0.331 +0.059/-0.000 8.4 +1.5/0 0.567 14.4 0.311 – 0.429 7.9 – 10.9 September 1999, Rev. C SOT-23 Tape and Reel Data and Package Dimensions, continued SOT-23 (FS PKG Code 49) 1:1 Scale 1:1 on letter size paper Dimensions shown below are in: inches [millimeters] Part Weight per unit (gram): 0.0082 September 1998, Rev. A1 TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. HiSeC™ ISOPLANAR™ MICROWIRE™ POP™ PowerTrench QFET™ QS™ Quiet Series™ SuperSOT™-3 SuperSOT™-6 ACEx™ Bottomless™ CoolFET™ CROSSVOLT™ E2CMOSTM FACT™ FACT Quiet Series™ FAST FASTr™ GTO™ SuperSOT™-8 SyncFET™ TinyLogic™ UHC™ VCX™ DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or 2. A critical component is any component of a life support device or system whose failure to perform can systems which, (a) are intended for surgical implant into be reasonably expected to cause the failure of the life the body, or (b) support or sustain life, or (c) whose support device or system, or to affect its safety or failure to perform when properly used in accordance with instructions for use provided in the labeling, can be effectiveness. reasonably expected to result in significant injury to the user. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Definition Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Preliminary First Production This datasheet contains preliminary data, and supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice in order to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild semiconductor. The datasheet is printed for reference information only. Rev. E