HER3001 THRU HER3006 30.0 AMP HIGH EFFICIENCY RECTIFIERS VOLTAGE RANGE 50 to 600 Volts CURRENT 30.0 Amperes FEATURES * Low forward voltage drop * High current capability * High reliability * High surge current capability * High speed switching TO-247 .635(16.13) .120(3.05) DIA. .115(2.92) .205(5.21) .195(4.49) .625(15.88) .320(8.13) .310(7.87) .180(4.53) .170(4.32) 30 .840(21.34) .820(20.83) MECHANICAL DATA .170(4.32) .150(3.81) .12(3.0) .11(2.8) * Case: Molded plastic * Epoxy: UL 94V-0 rate flame retardant * Lead: Lead solderable per MIL-STD-202, method 208 guranteed * Polarity: As Marked * Mounting position: Any PIN 1 + PIN 1 * Weight: 5.60 grams PIN 3 CASE PIN 2 PIN 3 .095 (2.4) .800(20.32) .770(19.56) .030(0.8) .020(0.5) .050(1.27) .045(1.14) .225(5.7) .205(5.2) Positive CT Suffix "C" CASE PIN 2 Negative CT Suffix "A" Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating 25 C ambient temperature uniess otherwies specified. Single phase half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYPE NUMBER Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current HER3001 HER3002 HER3003 HER3004 HER3005 HER3006 UNITS 50 35 50 100 70 100 200 140 200 .375"(9.5mm) Lead Length at Tc=75 C Peak Forward Surge Current, 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Instantaneous Forward Voltage at 15.0A Maximum DC Reverse Current Tc=25 C at Rated DC Blocking Voltage Tc=100 C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range TJ, TSTG NOTES: 1. Reverse Recovery Time test condition: IF=0.5A, IR=1.0A, IRR=0.25A 2. Measured at 1MHz and applied reverse voltage of 4.0V D.C. 300 210 300 400 280 400 600 420 600 A 30.0 300 1.0 1.3 1.85 10.0 200 60 100 -65 125 +150 V V V A V mA mA nS pF C RATING AND CHARACTERISTIC CURVES (HER3001 THRU HER3006) FIG.1-TYPICAL FORWARD FIG.2-TYPICAL FORWARD CURRENT DERATING CURVE CHARACTERISTICS AVERAGE FORWARD CURRENT,(A) 03 00 HE R3 00 HE R3 6 430 05 130 00 10.0 HE R3 1.0 30 25 20 15 Single Phase Half Wave 60Hz 10 Resistive Or Inductive Load 5 0 0 20 40 60 Tj=25 C 80 100 120 140 160 180 200 CASE TEMPERATURE ( C) Pulse Width 300us 1% Duty Cycle .1 FIG.4-MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT .4 .6 .8 1.0 1.2 1.4 1.6 FORWARD VOLTAGE,(V) FIG.3- TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTICS 50W NONINDUCTIVE 10W NONINDUCTIVE ( ) (+) D.U.T. 25Vdc (approx.) PULSE GENERATOR (NOTE 2) ( ) PEAK FORWARD SURGE CURRENT,(A) 500 .01 .2 400 300 Sine Wave 200 JEDEC method 100 0 1 5 2. Rise Time= 10ns max., Source Impedance= 50 ohms. | | | | | | | | 0 -0.25A 100 FIG.5-TYPICAL JUNCTION CAPACITANCE NOTES: 1. Rise Time= 7ns max., Input Impedance= 1 megohm.22pF. +0.5A 50 10 NUMBER OF CYCLES AT 60Hz OSCILLISCOPE (NOTE 1) trr 8.3ms Single Half Tj=25 C (+) 1W NONINDUCTIVE 175 JUNCTION CAPACITANCE,(pF) INSTANTANEOUS FORWARD CURRENT,(A) 100 150 125 100 75 50 25 0 -1.0A 1cm SET TIME BASE FOR 50 / 10ns / cm 0.1 0.5 1 2 5 10 20 REVERSE VOLTAGE,(V) 50 100 200 500 1000