SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 D D D D D D D D D D Members of the Texas Instruments Widebus Family Inputs Are TTL-Voltage Compatible Inverting Data Paths Independent Registers and Enables for A and B Buses Multiplexed Real-Time and Stored Data Flow-Through Architecture Optimizes PCB Layout Distributed VCC and GND Pin Configurations Minimize High-Speed Switching Noise EPIC (Enhanced-Performance Implanted CMOS) 1-µm Process 500-mA Typical Latch-Up Immunity at 125°C Packaged in Plastic 300-mil Shrink Small-Outline (DL) Packages and 380-mil Fine-Pitch Ceramic Flat (WD) Packages Using 25-mil Center-to-Center Pin Spacings description The SN54ACT16651 and 74ACT16651 are 16-bit bus transceivers that consist of D-type flip-flops and control circuitry arranged for multiplexed transmission of data directly from the data bus or from the internal storage registers. These devices can be used as two 8-bit transceivers or one 16-bit transceiver. Complementary output-enable (OEAB and OEBA) inputs are provided to control the transceiver functions. Select-control (SAB and SBA) inputs are provided to select whether real-time or stored data is transferred. A low input level selects real-time data, and a high input level selects stored data. The circuitry used for select control eliminates the typical decoding glitch that occurs in a multiplexer during the transition between stored and real-time data. Figure 1 illustrates the four fundamental bus-management functions that can be performed with the SN54ACT16651 and 74ACT16651. SN54ACT16651 . . . WD PACKAGE 74ACT16651 . . . DL PACKAGE (TOP VIEW) 1OEAB 1CLKAB 1SAB GND 1A1 1A2 VCC 1A3 1A4 1A5 GND 1A6 1A7 1A8 2A1 2A2 2A3 GND 2A4 2A5 2A6 VCC 2A7 2A8 GND 2SAB 2CLKAB 2OEAB 1 56 2 55 3 54 4 53 5 52 6 51 7 50 8 49 9 48 10 47 11 46 12 45 13 44 14 43 15 42 16 41 17 40 18 39 19 38 20 37 21 36 22 35 23 34 24 33 25 32 26 31 27 30 28 29 1OEBA 1CLKBA 1SBA GND 1B1 1B2 VCC 1B3 1B4 1B5 GND 1B6 1B7 1B8 2B1 2B2 2B3 GND 2B4 2B5 2B6 VCC 2B7 2B8 GND 2SBA 2CLKBA 2OEBA Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. EPIC and Widebus are trademarks of Texas Instruments Incorporated. Copyright 1996, Texas Instruments Incorporated UNLESS OTHERWISE NOTED this document contains PRODUCTION DATA information current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 description (continued) Data on the A or B bus, or both, can be stored in the internal D flip-flops by low-to-high transitions at the appropriate clock (CLKAB or CLKBA) inputs regardless of the levels on the select-control or output-enable inputs. When SAB and SBA are in the real-time transfer mode, it is also possible to store data without using the internal D-type flip-flops by simultaneously enabling OEAB and OEBA. In this configuration, each output reinforces its input. Thus, when all other data sources to the two sets of bus lines are at high impedance, each set of bus lines remains at its last state. The 74ACT16651 is packaged in TI’s shrink small-outline package, which provides twice the I/O pin count and functionality of standard small-outline packages in the same printed-circuit-board area. The SN54ACT16651 is characterized for operation over the full military temperature range of –55°C to 125°C. The 74ACT16651 is characterized for operation from –40°C to 85°C. FUNCTION TABLE DATA I/O† INPUTS OPERATION OR FUNCTION OEAB OEBA CLKAB CLKBA SAB SBA A1–A8 B1–B8 L H L L X X Input Input Isolation L H ↑ ↑ X X Input H ↑ L X Input H H ↑ ↑ X X‡ Input Unspecified‡ Store A and B data X X Input Output Store A in both registers L X L ↑ X Unspecified‡ Input Hold A, store B L L ↑ ↑ X X X‡ Output Input Store B in both registers L L X X X L Output Input Real-time B data to A bus Store A, hold B L L X L X H Output Input Stored B data to A bus H H X X L X Input Output Real-time A data to B bus H H L X H X Input Output Stored A data to B bus Output Stored A data to B bus and stored B data to A bus H L L L H H Output † The data-output functions may be enabled or disabled by a variety of level combinations at OEAB or OEBA. Data-input functions are always enabled; i.e., data at the bus terminals is stored on every low-to-high transition of the clock inputs. ‡ Select control = L; clocks can occur simultaneously. Select control = H; clocks must be staggered to load both registers. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS OEAB OEBA L L CLKAB CLKBA SAB X X X BUS B BUS A BUS A BUS B SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 SBA L OEAB OEBA H H OEBA H X H CLKAB CLKBA SAB ↑ X ↑ X ↑ ↑ SAB L X X X SBA X BUS B BUS A BUS A OEAB X L L CLKBA X REAL-TIME TRANSFER BUS A TO BUS B BUS B REAL-TIME TRANSFER BUS B TO BUS A CLKAB X SBA X X X STORAGE FROM A, B, OR A AND B OEAB H OEBA L CLKAB CLKBA SAB SBA L L H H TRANSFER STORED DATA TO A AND/OR B Figure 1. Bus-Management Functions POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 logic symbol† 56 1OEBA 1OEAB 1CLKBA 1SBA 1CLKAB 1SAB 2OEBA 2OEAB 2CLKBA 2SBA 2CLKAB 2SAB 1A1 1 55 54 2 EN1 [BA] EN2 [AB] C3 G4 C5 3 29 28 30 31 27 26 G6 EN7 [BA] EN8 [AB] C9 G10 C11 G12 ≥1 5 3D 4 1 52 1B1 4 1 5D 1A2 1A3 1A4 1A5 1A6 1A7 1A8 2A1 6 1 6 ≥1 2 6 51 8 49 9 48 10 47 12 45 13 44 14 43 ≥1 15 10 7 9D 42 1B2 1B3 1B4 1B5 1B6 1B7 1B8 2B1 10 1 11D 12 ≥1 8 2A2 2A3 2A4 2A5 2A6 2A7 2A8 16 1 12 40 19 38 20 37 21 36 23 34 24 33 † This symbol is in accordance with ANSI/IEEE Std 91-1984 and IEC Publication 617-12. 4 41 17 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 2B2 2B3 2B4 2B5 2B6 2B7 2B8 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 logic diagram (positive logic) 1OEBA 1OEAB 1CLKBA 1SBA 56 1 55 54 1CLKAB 2 3 1SAB C1 TG 1A1 1D 5 TG C1 TG 1D 52 TG 1B1 To Seven Other Channels 2OEBA 2OEAB 2CLKBA 2SBA 29 28 30 31 2CLKAB 27 26 2SAB C1 TG 2A1 1D 15 TG C1 TG 1D 42 TG 2B1 To Seven Other Channels POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0 or VI > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±400 mA Maximum package power dissipation at TA = 55°C (in still air) (see Note 2): DL package . . . . . . . . . . . 1.4 W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. The maximum package power dissipation is calculated using a junction temperature of 150_C and a board trace length of 750 mils. recommended operating conditions (see Note 3) SN54ACT16651 NOM MAX MIN NOM MAX 4.5 5 5.5 4.5 5 5.5 VCC VIH Supply voltage VIL VI Low-level input voltage Input voltage 0 VO IOH Output voltage 0 High-level output current IOL ∆t/∆v Low-level output current High-level input voltage 2 2 0.8 Input transition rise or fall rate TA Operating free-air temperature NOTE 3: Unused inputs must be held high or low to prevent them from floating. POST OFFICE BOX 655303 UNIT V V 0.8 V VCC VCC V –24 –24 mA 24 24 mA VCC VCC 0 0 V 0 10 0 10 ns/V –55 125 –40 85 °C PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 6 74ACT16651 MIN • DALLAS, TEXAS 75265 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS 4.5 V IOH = –50 50 µA VOH 24 mA IOH = –24 IOH = –50 mA† IOH = –75 mA† II IOZ‡ A or B ports ICC ∆ICC§ Ci Control inputs Cio A or B ports TA = 25°C SN54ACT16651 TYP MAX MIN MAX 74ACT16651 MIN 4.4 4.4 4.4 5.5 V 5.4 5.4 5.4 4.5 V 3.94 3.7 3.8 5.5 V 4.94 4.7 4.8 MAX UNIT V 3.85 5.5 V IOL = 24 mA Control inputs MIN 5.5 V IOL = 50 µA VOL VCC 3.85 4.5 V 0.1 0.1 5.5 V 0.1 0.1 0.1 0.1 4.5 V 0.36 0.5 0.44 5.5 V 0.36 0.5 0.44 V IOL = 50 mA† IOL = 75 mA† 5.5 V VI = VCC or GND VO = VCC or GND 5.5 V ±0.1 ±1 ±1 µA 5.5 V ±0.5 ±10 ±5 µA VI = VCC or GND, IO = 0 One input at 3.4 V, Other inputs at VCC or GND 5.5 V 8 160 80 µA 5.5 V 0.9 1 1 mA 1.65 5.5 V VI = VCC or GND VO = VCC or GND 1.65 5V 4 pF 5V 12 pF † Not more than one output should be tested at a time, and the duration of the test should not exceed 10 ms. ‡ For I/O ports, the parameter IOZ includes the input leakage current. § This is the increase in supply current for each input that is at one of the specified TTL voltage levels rather than 0 V or VCC. timing requirements over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 2) TA = 25°C SN54ACT16651 MIN MAX MIN MAX 0 0 90 MIN MAX 0 90 UNIT fclock tw Clock frequency Pulse duration, CLKAB or CLKBA high or low 5.5 5.5 5.5 ns tsu th Setup time, A before CLKAB↑ or B before CLKBA↑ 5.3 5.3 5.3 ns 1 1 1 ns Hold time, A after CLKAB↑ or B after CLKBA↑ 90 74ACT16651 MHz PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 switching characteristics over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 2) PARAMETER fmax tPLH tPHL tPLH tPHL tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ tPZH tPZL tPHZ tPLZ FROM (INPUT) TO (OUTPUT) MIN TA = 25°C SN54ACT16651 TYP MAX MIN MAX 90 A or B B or A CLKBA or CLKAB A or B SBA or SAB (with A or B high) A or B SBA or SAB (with A or B low) A or B OEBA A OEBA A OEAB B OEAB B 74ACT16651 MIN 90 MAX 90 UNIT MHz 3 6.6 10 3 12.2 3 11.3 4.6 8 10.6 4.6 12.7 4.6 11.9 5.4 9.1 12 5.4 14.8 5.4 13.7 5.4 9.1 12 5.4 14.6 5.4 13.6 4.6 7.9 10.5 4.6 13.1 4.6 12.1 5.4 10.9 15.5 5.4 19.6 5.4 17.8 5 10.4 14.9 5 19.2 5 17.3 4.9 8.6 11.9 4.9 13.7 4.9 12.7 3.2 7.2 10.8 3.2 13.6 3.2 12.3 3.8 8 12.2 3.8 15.3 3.8 13.9 5.1 7.8 9.8 5.1 11.3 5.1 10.6 4.9 7.7 9.9 4.9 11.4 4.9 10.8 4.9 8 10.5 4.9 12.9 4.9 11.9 5.4 8.8 11.8 5.4 14.7 5.4 13.5 4.3 7.5 10.7 4.3 12 4.3 11.4 4.5 7.6 10.8 4.5 12.3 4.5 11.6 ns ns ns ns ns ns ns ns operating characteristics, VCC = 5 V, TA = 25°C PARAMETER Cpd d Power dissipation capacitance per transceiver TEST CONDITIONS Outputs enabled Outputs disabled PRODUCT PREVIEW information concerns products in the formative or design phase of development. Characteristic data and other specifications are design goals. Texas Instruments reserves the right to change or discontinue these products without notice. 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 pF CL = 50 pF, f = 1 MHz TYP 62 14 UNIT pF SN54ACT16651, 74ACT16651 16-BIT TRANSCEIVERS AND REGISTERS WITH 3-STATE OUTPUTS SCAS449A – FEBRUARY 1993 – REVISED APRIL 1996 PARAMETER MEASUREMENT INFORMATION 2 × VCC S1 500 Ω From Output Under Test Open GND TEST S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open 2 × VCC GND 500 Ω CL = 50 pF (see Note A) LOAD CIRCUIT 3V Timing Input 1.5 V 0V tw tsu 3V Input 1.5 V th 1.5 V 3V 1.5 V 1.5 V Data Input 0V 0V VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS Output Control (low-level enabling) 3V 1.5 V Input 1.5 V 0V tPHL tPLH In-Phase Output 50% VCC 50% VCC 0V tPZL tPLZ Output Waveform 1 S1 at 2 × VCC (see Note B) tPLH tPHL Out-of-Phase Output VOH 50% VCC VOL 3V VOH 50% VCC VOL Output Waveform 2 S1 at GND (see Note B) 1.5 V 1.5 V 50% VCC 20% VCC VOL tPHZ tPZH VOLTAGE WAVEFORMS ≈ VCC 50% VCC 80% VCC VOH ≈0V VOLTAGE WAVEFORMS NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr = 3 ns, tf = 3 ns. D. The outputs are measured one at a time with one input transition per measurement. Figure 2. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 6-Dec-2006 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74ACT16651DL ACTIVE SSOP DL 56 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ACT16651DLG4 ACTIVE SSOP DL 56 20 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ACT16651DLR ACTIVE SSOP DL 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74ACT16651DLRG4 ACTIVE SSOP DL 56 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device 74ACT16651DLR Package Package Pins Type Drawing SSOP DL 56 SPQ Reel Reel Diameter Width (mm) W1 (mm) 1000 330.0 32.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 11.35 18.67 3.1 16.0 32.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 74ACT16651DLR SSOP DL 56 1000 346.0 346.0 49.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated