HT24LC04 CMOS 4K 2-Wire Serial EEPROM Features · Operating voltage: 2.2V~5.5V · Partial page write allowed · Low power consumption · 16-byte page write modes - Operation: 5mA max. - Standby: 5mA max. · Write operation with built-in timer · Hardware controlled write protection · Internal organization: 512´8 · 40-year data retention · 2-wire serial interface · 106 erase/write cycles per word · Write cycle time: 5ms max. · Commercial temperature range (0°C to +70°C) · Automatic erase-before-write operation · 8-pin DIP/SOP package General Description The HT24LC04 is a 4K-bit serial read/write non-volatile memory device using the CMOS floating gate process. Its 4096 bits of memory are organized into 512 words and each word is 8 bits. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. Up to four HT24LC04 devices may be connected to the same two-wire bus. The HT24LC04 is guaranteed for 1M erase/write cycles and 40-year data retention. Block Diagram Pin Assignment S C L S D A I/O C o n tro l L o g ic H V P u m p X W P M e m o ry C o n tro l L o g ic E E P R O M A rra y D E A 0 1 8 V C C A 1 2 7 W P A 2 3 6 S C L V S S 4 5 S D A H T 2 4 L C 0 4 8 D IP -A /S O P -A C P a g e B u f Y D E C A 0 ~ A 2 A d d re s s C o u n te r S e n s e A M P R /W C o n tro l V C C V S S Rev. 1.30 1 November 25, 2003 HT24LC04 Pin Description Pin No. Pin Name I/O I Description 1~3 A0~A2 Address inputs 4 VSS ¾ Negative power supply 5 SDA I/O Serial data inputs/output 6 SCL I Serial clock data input 7 WP I Write protect 8 VCC ¾ Positive power supply Absolute Maximum Ratings Operating Temperature (Commercial) ........................................................................................................ 0°C to 70°C Storage Temperature ............................................................................................................................-50°C to 125°C Applied VCC Voltage with Respect to VSS ..................................................................................VSS -0.3V to VCC+6.0V Applied Voltage on any Pin with Respect to VSS .................................................................................................VSS-0.3V to VCC+0.3V Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. D.C. Characteristics Symbol Parameter Ta=0°C to 70°C Test Conditions VCC Conditions ¾ VCC Operating Voltage ¾ Min. Typ. Max. Unit 2.2 ¾ 5.5 V ¾ ¾ 2 mA ICC1 Operating Current 5V Read at 100kHz ICC2 Operating Current 5V Write at 100kHz ¾ ¾ 5 mA VIL Input Low Voltage ¾ ¾ -1 ¾ 0.3VCC V VIH Input High Voltage ¾ ¾ 0.7VCC ¾ VCC+0.5 V VOL Output Low Voltage 2.4V IOL=2.1mA ¾ ¾ 0.4 V ILI Input Leakage Current 5V VIN=0 or VCC ¾ ¾ 1 mA ILO Output Leakage Current 5V VOUT=0 or VCC ¾ ¾ 1 mA ISTB1 Standby Current 5V VIN=0 or VCC ¾ ¾ 5 mA ISTB2 Standby Current 2.4V VIN=0 or VCC ¾ ¾ 4 mA CIN Input Capacitance (See Note) ¾ f=1MHz 25°C ¾ ¾ 6 pF COUT Output Capacitance (See Note) ¾ f=1MHz 25°C ¾ ¾ 8 pF Note: These parameters are periodically sampled but not 100% tested Rev. 1.30 2 November 25, 2003 HT24LC04 A.C. Characteristics Symbol Parameter Ta=0°C to 70°C Standard Mode* VCC=5V±10% Min. Max. Min. Max. Unit Remark fSK Clock Frequency ¾ 100 ¾ 400 kHz ¾ tHIGH Clock High Time 4000 ¾ 600 ¾ ns ¾ tLOW Clock Low Time 4700 ¾ 1200 ¾ ns ¾ tr SDA and SCL Rise Time ¾ 1000 ¾ 300 ns Note tf SDA and SCL Fall Time ¾ 300 ¾ 300 ns Note tHD:STA START Condition Hold Time 4000 ¾ 600 ¾ ns After this period the first clock pulse is generated tSU:STA START Condition Setup Time 4000 ¾ 600 ¾ ns Only relevant for repeated START condition tHD:DAT Data Input Hold Time 0 ¾ 0 ¾ ns ¾ ¾ tSU:DAT Data Input Setup Time 200 ¾ 100 ¾ ns tSU:STO STOP Condition Setup Time 4000 ¾ 600 ¾ ns ¾ tAA Output Valid from Clock ¾ 3500 ¾ 900 ns ¾ tBUF Bus Free Time 4700 ¾ 1200 ¾ ns Time in which the bus must be free before a new transmission can start tSP Input Filter Time Constant (SDA and SCL Pins) ¾ 100 ¾ 50 ns Noise suppression time tWR Write Cycle Time ¾ 5 ¾ 5 ms Note: ¾ These parameters are periodically sampled but not 100% tested * The standard mode means VCC=2.2V to 5.5V For relative timing, refer to timing diagrams Functional Description · Serial clock (SCL) VSS. When the write protect pin is connected to Vcc, the write protection feature is enabled and operates as shown in the following table. The SCL input is used for positive edge clock data into each EEPROM device and negative edge clock data out of each device. WP Pin Status · Serial data (SDA) The SDA pin is bidirectional for serial data transfer. The pin is open-drain driven and may be wired-OR with any number of other open-drain or open collector devices. Full Array (4K) At VSS Normal Read/Write Operations Memory Organization · HT24LC04, 4K Serial EEPROM · A0, A1, A2 Internally organized with 512 8-bit words, random word addressing requires a 9-bit data word address. The HT24LC04 uses the A2 and A1 inputs for hard wire addressing and a total of four 4K devices may be addressed on a single bus system. The A0 pin is not connected. (The device addressing is discussed in detail under the Device Addressing section). Device Operations · Clock and data transition Data transfer may be initiated only when the bus is not busy. During data transfer, the data line must remain stable whenever the clock line is high. Changes in data line while the clock line is high will be interpreted as a START or STOP condition. · Write protect (WP) The HT24LC04 has a write protect pin that provides hardware data protection. The write protect pin allows normal read/write operations when connected to the Rev. 1.30 Protect Array At VCC 3 November 25, 2003 HT24LC04 · Start condition The 8th bit of device address is the read/write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition Timing diagram). If the comparison of the device address succeed the EEPROM will output a zero at ACK bit. If not, the chip will return to a standby state. · Stop condition A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition Timing Diagram). 1 A 1 A 0 R /W A write operation requires an 8-bit data word address following the device address word and acknowledgment. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8-bit data word. After receiving the 8-bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle to the non-volatile memory. All inputs are disabled during this write cycle and EEPROM will not respond until the write is completed (refer to Byte write timing). S D A S C L S to p c o n d itio n Device Addressing · Page write The 4K EEPROM devices require an 8-bit device address word following a start condition to enable the chip for a read or write operation. The device address word consist of a mandatory one, zero sequence for the first four most significant bits (refer to diagram showing the Device Address). This is common to all the EEPROM device. The next three bits are the A2, A1 and A0 device address bits for the 1K/2K EEPROM. These three bits must compare to their corresponding hard-wired input pins. The 4K device is capable of 16-byte page writes. A page write is initiated the same as byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges the receipt of the first data word, the microcontroller can transmit up to fifteen more data words. The EEPROM will respond with a ze r o a f t e r e a ch d a t a w o r d r e ce i ve d . T h e microcontroller must terminate the page write sequence with a stop condition. The data word address lower four bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location (refer to Page write timing). The 4K EEPROM only use the A2 and A1 device address bits with the third bit as a memory page address bit. The two device address bits must compare to their corresponding hardwired input pins. The A0 pin is not connected. D e v ic e a d d r e s s S D A A 2 · Byte write D a ta a llo w e d to c h a n g e N o A C K s ta te 0 Write Operations All addresses and data words are serially transmitted to and from the EEPROM in 8-bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. A d d re s s o r a c k n o w le d g e v a lid 1 D e v ic e A d d r e s s · Acknowledge S ta rt c o n d itio n 0 S W o rd a d d re s s D A T A A 2 A 1 A 0 P R /W S ta rt A C K A C K A C K S to p Byte Write Timing D e v ic e a d d r e s s S D A W o rd a d d re s s D A T A n + 1 D A T A n P S S ta rt D A T A n + x A C K A C K A C K A C K S to p Page Write Timing Rev. 1.30 4 November 25, 2003 HT24LC04 · Acknowledge polling · Current address read To maximize bus throughput, one technique is to allow the master to poll for an acknowledge signal after the start condition and the control byte for a write command have been sent. If the device is still busy implementing its write cycle, then no ACK will be returned. The master can send the next read/write command when the ACK signal has finally been received. The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address roll over during read from the last byte of the last memory page to the first byte of the first page. The address roll over during write from the last byte of the current page to the first byte of the same page. Once the device address with the read/write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller should respond with a ²no ACK² signal (high) followed by a stop condition (refer to Current read timing). S e n d W r ite C o m m a n d S e n d S to p C o n d itio n to In itia te W r ite C y c le S e n d S ta rt · Random read S e n d C o tr o ll B y te w ith R /W = 0 (A C K = 0 )? A random read requires a dummy byte write sequence to load in the data word address which is then clocked in and acknowledged by the EEPROM. The microcontroller must then generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read/write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller should respond with a ²no ACK² signal (high) followed by a stop condition (refer to Random read timing). N o Y e s N e x t O p e r a tio n Acknowledge Polling Flow · Write protect The HT24LC04 has a write-protect function and programming will then be inhibited when the WP pin is connected to VCC. Under this mode, the HT24LC04 is used as a serial ROM. · Read operations The HT24LC04 supports three read operations, namely, current address read, random address read and sequential read. During read operation execution, the read/write select bit should be set to ²1². D e v ic e a d d r e s s S D A S D A T A S to p A 2 A 1 A 0 S ta rt P A C K N o A C K Current Read Timing D e v ic e a d d r e s s S D A S S ta rt A 2 W o rd a d d re s s D e v ic e a d d r e s s D A T A S A 1 A 0 A C K S to p P A C K S ta rt A C K N o A C K Random Read Timing Rev. 1.30 5 November 25, 2003 HT24LC04 · Sequential read words. When the memory address limit is reached, the data word address will roll over and the sequential read continues. The sequential read operation is terminated when the microcontroller responds with a ²no ACK² signal (high) followed by a stop condition. Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledgment. As long as the EEPROM receives an acknowledgment, it will continue to increment the data word address and serially clock out sequential data D e v ic e a d d r e s s S D A D A T A n D A T A n + 1 D A T A n + x S to p S P S ta rt N o A C K A C K A C K Sequential Read Timing Timing Diagrams tF tR S C L tS S D A U :S T A tS tL O W tH D :S T A tH IG H tH D :D A T tS U :D A T P tA S D A A V a lid O U T tS U :S T O tB U F V a lid S C L S D A 8 th b it A C K W o rd n tW S to p C o n d itio n Note: R S ta rt C o n d itio n The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the valid start condition of sequential command. Rev. 1.30 6 November 25, 2003 HT24LC04 Package Information 8-pin DIP (300mil) Outline Dimensions A 8 B 5 4 1 H C D = G E I F Symbol Rev. 1.30 Dimensions in mil Min. Nom. Max. A 355 ¾ 375 B 240 ¾ 260 C 125 ¾ 135 D 125 ¾ 145 E 16 ¾ 20 F 50 ¾ 70 G ¾ 100 ¾ H 295 ¾ 315 I 335 ¾ 375 a 0° ¾ 15° 7 November 25, 2003 HT24LC04 8-pin SOP (150mil) Outline Dimensions 5 8 A B 4 1 C C ' G H D E Symbol Rev. 1.30 = F Dimensions in mil Min. Nom. Max. A 228 ¾ 244 B 149 ¾ 157 C 14 ¾ 20 C¢ 189 ¾ 197 D 53 ¾ 69 E ¾ 50 ¾ F 4 ¾ 10 G 22 ¾ 28 H 4 ¾ 12 a 0° ¾ 10° 8 November 25, 2003 HT24LC04 Product Tape and Reel Specifications Reel Dimensions D T 2 A C B T 1 SOP 8N Symbol Description A Reel Outer Diameter B Reel Inner Diameter Dimensions in mm 330±1.0 62±1.5 13.0+0.5 -0.2 C Spindle Hole Diameter D Key Slit Width 2.0±0.15 T1 Space Between Flange 12.8+0.3 -0.2 T2 Reel Thickness 18.2±0.2 Rev. 1.30 9 November 25, 2003 HT24LC04 Carrier Tape Dimensions P 0 D P 1 t E F W C D 1 B 0 P K 0 A 0 SOP 8N Symbol Description Dimensions in mm W Carrier Tape Width 12.0+0.3 -0.1 P Cavity Pitch 8.0±0.1 E Perforation Position 1.75±0.1 F Cavity to Perforation (Width Direction) 5.5±0.1 D Perforation Diameter 1.55±0.1 D1 Cavity Hole Diameter 1.5+0.25 P0 Perforation Pitch 4.0±0.1 P1 Cavity to Perforation (Length Direction) 2.0±0.1 A0 Cavity Length 6.4±0.1 B0 Cavity Width 5.20±0.1 K0 Cavity Depth 2.1±0.1 t Carrier Tape Thickness 0.3±0.05 C Cover Tape Width Rev. 1.30 9.3 10 November 25, 2003 HT24LC04 Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031 Tel: 0755-8346-5589 Fax: 0755-8346-5590 ISDN: 0755-8346-5591 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holmate Semiconductor, Inc. (North America Sales Office) 46712 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright Ó 2003 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek¢s products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. Rev. 1.30 11 November 25, 2003