HT82K68E Preliminary Multimedia Keyboard Encoder OTP Features · · · · · · · Operating voltage: 2.8V~5.5V 34(42-pin)/32(40-pin) bidirectional I/O lines One 8-bit programmable timer counter with overflow interrupts Crystal or RC oscillator Watchdog Timer 3K´16 OTP EPROM 160´8 data RAM · · · · · · · HALT function and wake-up feature reduce power consumption Six-level subroutine nesting Bit manipulation instructions 16-bit table read instructions 63 powerful instructions All instructions in 1 or 2 machine cycles 40/42-pin DIP package General Description The program and option PROM can be electrically programmed making the HT82K68E suitable for use in product development. The HT82K68E is an 8-bit high performance peripheral interface IC, designed for multiple I/O products and multimedia applications. It supports interface to a low speed PC with multimedia keyboard or wireless keyboard in Windows 95, Windows 98 or Windows 2000 environment. A HALT feature is included to reduce power consumption. 1 August 8, 2000 Preliminary HT82K68E Block Diagram S T A C K 0 S T A C K 1 S T A C K 2 S T A C K 3 P ro g ra m E P R O M In te rru p t C ir c u it S T A C K 4 S T A C K 5 P ro g ra m C o u n te r IN T C S Y S C L K /4 T M R T M R C In s tr u c tio n R e g is te r M P 0 M P 1 M U X 8 b it S Y S C L K /4 W D T S D A T A M e m o ry W D T P r e s c a le r W D T M U X R C In s tr u c tio n D e c o d e r P E C M U X A L U T im in g G e n e ra to r P O R T E P E P D C S T A T U S P O R T D P D S h ifte r P C C P O R T C P C O S C 2 O S R E V D V S S C 1 S E T D A C C P B C P O R T B P B P A C P A 2 P O R T A O S C P E 0 ~ P E 4 P D 0 ~ P D 7 P C 0 ~ P C 7 P B 0 ~ P B 7 P A 0 ~ P A 7 August 8, 2000 Preliminary HT82K68E Pin Assignment P B 5 1 4 2 P B 6 P B 5 1 4 0 P B 6 P B 4 2 4 1 P B 7 P B 4 2 3 9 P B 7 P A 3 3 4 0 P A 4 P A 3 3 3 8 P A 4 P A 2 4 3 9 P A 5 P A 2 4 3 7 P A 5 P A 1 5 3 8 P A 6 P A 1 5 3 6 P A 6 P A 0 6 3 7 P A 7 P A 0 6 3 5 P A 7 P B 3 7 3 6 O S C 2 P B 3 7 3 4 O S C 2 P B 2 8 3 5 O S C 1 P B 2 8 3 3 O S C 1 P B 1 9 3 4 V D D P B 1 9 3 2 V D D P B 0 1 0 3 3 R E S E T P B 0 1 0 3 1 R E S E T P D 7 1 1 3 2 P E 4 (L E D ) P D 7 1 1 3 0 P E 4 (L E D ) P D 6 1 2 3 1 P D 3 P D 6 1 2 2 9 P D 3 P D 5 1 3 3 0 P D 2 P D 5 1 3 2 8 P D 2 P D 4 1 4 2 9 P D 1 P D 4 1 4 2 7 P D 1 V S S 1 5 2 8 P D 0 V S S 1 5 2 6 P D 0 P E 2 (L E D ) 1 6 2 7 P C 7 P E 2 (L E D ) 1 6 2 5 P C 7 P E 3 (L E D ) 1 7 2 6 P C 6 P E 3 (L E D ) 1 7 2 4 P C 6 P C 0 1 8 2 5 P C 5 P C 0 1 8 2 3 P C 5 P C 1 1 9 2 4 P C 4 P C 1 1 9 2 2 P C 4 P C 2 2 0 2 3 P C 3 P C 2 2 0 2 1 P C 3 P E 0 2 1 2 2 P E 1 H T 8 2 K 6 8 E 4 0 D IP H T 8 2 K 6 8 E 4 2 D IP Pin Description Pin Name I/O ROM Code Option Description Bidirectional 8-bit input/output port. Each bit can be configured as a wake-up input by ROM code option. Software* instructions determine the CMOS output or schmitt trigger input with or without pull-high resistor 12K. PA0~PA7 I/O Wake-up Pull-high or None PB0~PB7 I/O Pull-high or None Bidirectional 8-bit input/output port. Software* instructions determine the CMOS output or schmitt trigger input with or without pull-high resistor. PC0 I/O Wake-up Pull-high or None This pin is an I/O port. Open drain output with pull-high resistor and can be used as DATA or CLOCK line of PS2. This pin can be configured as a wake-up input by ROM code option. PC1 I/O Wake-up Pull-high or None This pin is an I/O port. open drain output with pull-high resistor and can be used as DATA or CLOCK line of . This pin can be configured as a wake-up input by ROM code option. 3 August 8, 2000 Preliminary Pin Name I/O HT82K68E ROM Code Option Description Bidirectional 2-bit input/output port. Each bit can be configured as a wake-up input by ROM code option. Software* instructions determine the CMOS output or schmitt trigger input with or without pull-high resistor. PC2~PC3 I/O Wake-up Pull-high or None PC4~PC7 I/O Pull-high or None Bidirectional 4-bit input/output port. Software* instructions determine the CMOS output or schmitt trigger input with or without pull-high resistor. PD0~PD7 I/O Pull-high or None Bidirectional 8-bit input/output port. Software* instructions determine the CMOS output or schmitt trigger input with or without pull-high resistor. PE0~PE1 I/O Pull-high or None Bidirectional input/output port. Software* instructions determine the CMOS output or schmitt trigger input with or without pull-high resistor. PE2~PE4 O ¾ This pin is an NMOS output structure. The pad can function as LED drivers for the keyboard. IOL=14mA, @VOL=3.2V VDD ¾ ¾ Positive power supply VSS ¾ ¾ Negative power supply, ground RESET I ¾ Chip reset input. Active low. Built-in power-on reset circuit to reset the entire chip. Chip can also be externally reset via RESET pin OSC1 OSC2 I O Crystal or RC OSC1, OSC2 are connected to an RC network or a crystal for the internal system clock. In the case of RC operation, OSC2 is the output terminal for the 1/4 system clock; A 110kW resistor is connected to OSC1 to generate a 2MHZ frequency. Note: *: Software means the ROM code option can be configured by HT-IDE (Holtek Integrated Development Environment). Absolute Maximum Ratings Supply Voltage .............................-0.3V to 5.5V Storage Temperature ................-50°C to 125°C Input Voltage ................VSS-0.3V to VDD+0.3V Operating Temperature .............-25°C to 70°C Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability. 4 August 8, 2000 Preliminary HT82K68E D.C. Characteristics Symbol Parameter Ta=25°C Test Conditions VDD Conditions ¾ VDD Operating Voltage ¾ IDD1 Operating Current (Crystal OSC) 3V 5V IDD2 Operating Current (RC OSC) 5V ISTB1 Standby Current (WDT enabled) ISTB2 Standby Current (WDT Disabled) VIL Input Low Voltage for I/O Ports 3V VIH Input High Voltage for I/O Ports VIL1 Min. Typ. Max. Unit 2.8 ¾ 5.5 V ¾ 0.7 1.5 mA ¾ 2 5 mA ¾ 1 1.5 mA ¾ 2 5 mA ¾ ¾ 8 mA ¾ ¾ 15 mA ¾ ¾ 3 mA ¾ ¾ 6 mA ¾ 0 ¾ 1 V 5V ¾ 0 ¾ 1.5 V 3V ¾ 2.1 ¾ 3 V 5V ¾ 3.5 ¾ 5 V Input Low Voltage (RESET) 3V ¾ 0 ¾ 0.7 V 5V ¾ 0 ¾ 1.3 V VIH1 Input High Voltage (RESET) 3V ¾ 2.5 ¾ 3 V ¾ 4.1 ¾ 5 V IOL I/O Port Sink Current 5V VOL= 0.5V 7 15 ¾ mA IOH I/O Port Source Current 5V VOH= 4.5V -2.5 -4.5 ¾ mA ILED LED Sink Current 5V VOL=3.2V 10 14 18 mA tPOR Power-on Reset Time 5V ¾ 120 150 180 ms RPH Internal Pull-high Resistance of PA, PB, PC, PD, PE Port 5V ¾ 5 12 20 kW RPH1 Internal Pull-high Resistance of DATA, CLK 5V ¾ 2 5 8 kW Df/f Frequency Variation 5V Crystal ¾ ¾ ±1 % Df/f1 Frequency Variation 5V RC ¾ ¾ ±10 % 3V 3V 5V 3V 5V No load, fSYS= 2MHz No load, fSYS= 2MHz No load, system HALT No load, system HALT 5V 5 August 8, 2000 Preliminary HT82K68E A.C. Characteristics Symbol Parameter fSYS1 System Clock (Crystal OSC) fSYS2 System Clock (RC OSC) Ta=25°C Test Conditions Min. Typ. Max. Unit VDD Conditions 3V ¾ ¾ 2 ¾ MHz 5V ¾ ¾ 2 20 MHz 3V ¾ ¾ 2 ¾ MHz 5V ¾ ¾ 2 20 MHz 3V ¾ 45 90 180 ms 5V ¾ 35 65 130 ms 12 23 45 ms 9 17 35 ms ¾ 1024 ¾ tSYS tWDTOSC Watchdog Oscillator tWDT1 Watchdog Time-out Period (RC) tWDT2 Watchdog Time-out Period (System Clock) ¾ tRES External Reset Low Pulse Width ¾ ¾ 1 ¾ ¾ ms tSST System Start-up Timer Period ¾ Power-up or wake-up from HALT ¾ 1024 ¾ tSYS tINT Interrupt Pulse Width ¾ ¾ 1 ¾ ¾ ms Note: 3V 5V Without WDT prescaler Without WDT prescaler tSYS= 1/fSYS 6 August 8, 2000 Preliminary HT82K68E Functional Description nal interrupt or return from subroutine, the PC manipulates the program transfer by loading the address corresponding to each instruction. Execution flow The HT82K68E system clock is derived from either a crystal or an RC oscillator. The system c l o c k i s i nter na l l y d i v i d ed i n t o f o u r non-overlapping clocks. One instruction cycle consists of four system clock cycles. The conditional skip is activated by instruction. Once the condition is met, the next instruction, fetched during the current instruction execution, is discarded and a dummy cycle replaces it to get the proper instruction. Otherwise proceed with the next instruction. Instruction fetching and execution are pipelined in such a way that a fetch takes one instruction cycle while decoding and execution takes the next instruction cycle. However, the pipelining scheme causes each instruction to effectively execute within one cycle. If an instruction changes the program counter, two cycles are required to complete the instruction. The lower byte of the program counter (PCL) is a readable and writeable register (06H). Moving data into the PCL performs a short jump. The destination will be within 256 locations. Once a control transfer takes place, an additional dummy cycle is required. Program counter - PC Program memory - PROM The 12-bit program counter (PC) controls the sequence in which the instructions stored in the program ROM are executed and its contents specify a maximum of 4096 addresses. The program memory is used to store the program instructions which are to be executed. It also contains data, table, and interrupt entries, and is organized with 3072 ´ 16 bits, addressed by the program counter and table pointer. After accessing a program memory word to fetch an instruction code, the contents of the program counter are incremented by one. The program counter then points to the memory word containing the next instruction code. Certain locations in the program memory are reserved for special usage: · Location 000 When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, exterT 1 S y s te m T 2 T 3 T 4 This area is reserved for the initialization program. After chip reset, the program always begins execution at location 000H. T 1 T 2 T 3 T 4 T 1 T 2 T 3 T 4 C lo c k O S C 2 ( R C o n ly ) ( N M O S o p e n d r a in o u tp u t) P C P C P C + 1 F e tc h IN S T (P C ) E x e c u te IN S T (P C -1 ) F e tc h IN S T (P C + 1 ) E x e c u te IN S T (P C ) P C + 2 F e tc h IN S T (P C + 2 ) E x e c u te IN S T (P C + 1 ) Execution flow 7 August 8, 2000 Preliminary HT82K68E · Location 008H This area is reserved for the timer counter interrupt service program. If timer interrupt results from a timer counter overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 008H. 0 0 0 H 0 0 8 H T im e r /e v e n t c o u n te r in te r r u p t s u b r o u tin e n 0 0 H · Table location P ro g ra m P R O M L o o k - u p ta b le ( 2 5 6 w o r d s ) n F F H Any location in the PROM space can be used as look-up tables. The instructions TABRDC [m] (the current page, 1 page=256 words) and TABRDL [m] (the last page) transfer the contents of the lower-order byte to the specified data memory, and the higher-order byte to TBLH (08H). Only the destination of the lower-order byte in the table is well-defined, the other bits of the table word are transferred to the lower portion of TBLH, the remaining 1 bit is read as 0. The Table Higher-order byte register (TBLH) is read only. The TBLH is read only and cannot be restored. If the main routine and the ISR (Interrupt Service Routine) both employ the table read instruction, the contents of the TBLH in the main routine are likely to be changed by the table read instruction used in the ISR. Errors can occur. In other words, using the table read instruction in the main routine and the ISR simultaneously should be avoided. HowMode D e v ic e in itia liz a tio n p r o g r a m L o o k - u p ta b le ( 2 5 6 w o r d s ) B F F H 1 6 b its N o te : n ra n g e s fro m 0 to B Program memory ever, if the table read instruction has to be applied in both the main routine and the ISR, the interrupt is supposed to be disabled prior to the table read instruction. It will not be enabled until the TBLH has been backed up. The table pointer (TBLP) is a read/write register (07H), which indicates the table location. Before accessing the table, the location must be placed in TBLP. All table related instructions need 2 cycles to complete the operation. These areas may function as normal program memory depending upon the requirements. Program Counter *11 *10 *9 *8 *7 *6 *5 *4 *3 *2 *1 *0 Initial reset 0 0 0 0 0 0 0 0 0 0 0 0 Timer counter overflow 0 0 0 0 0 0 0 0 1 0 0 0 Skip PC+2 Loading PCL *11 *10 *9 *8 @7 @6 @5 @4 @3 @2 @1 @0 Jump, call branch #11 #10 #9 #8 #7 #6 #5 #4 #3 #2 #1 #0 Return from subroutine S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 Note: *11~*0: Program counter bits #11~#0: Instruction code bits S11~S0: Stack register bits @7~@0: PCL bits 8 August 8, 2000 Preliminary Stack register - STACK 0 0 H This is a special part of the memory which is used to save the contents of the program counter (PC) only. The stack is organized into six levels and is neither part of the data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the stack pointer (SP) and is neither readable nor writeable. At a subroutine call or interrupt acknowledgement, the contents of the program counter are pushed onto the stack. At the end of a subroutine or an interrupt routine, signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the stack. After a chip reset, the SP will point to the top of the stack. In d ir e c t A d d r e s s in g R e g is te r 0 0 1 H M P 0 0 2 H In d ir e c t A d d r e s s in g R e g is te r 1 0 3 H M P 1 0 4 H A C C 0 5 H 0 6 H P C L 0 7 H T B L P 0 8 H T B L H 0 9 H W D T S 0 A H S T A T U S 0 B H IN T C 0 C H 0 D H T M R 0 E H T M R C S p e c ia l P u r p o s e D A T A M E M O R Y 0 F H 1 0 H 1 1 H If the stack is full and a non-masked interrupt takes place, the interrupt request flag will be recorded but the acknowledgement will be inhibited. When the stack pointer is decremented (by RET or RETI), the interrupt will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily. In a similar case, if the stack is full and a ²CALL² is subsequently executed, stack overflow occurs and the first entry will be lost (only the most recent four return addresses are stored). 1 2 H P A 1 3 H P A C 1 4 H P B 1 5 H P B C 1 6 H P C 1 7 H P C C 1 8 H P D 1 9 H P D C 1 A H P E 1 B H P E C : U n u s e d . 1 C H 1 D H R e a d a s ² 0 0 ² 1 E H 1 F H 2 0 H 6 0 H Data memory - RAM G e n e ra l P u rp o s e D A T A M E M O R Y (1 6 0 B y te s ) The data memory is designed with 184 ´ 8 bits. It is divided into two functional groups: special function registers and general purpose data memory (160´8). Most of them are read/write, but some are read only. F F H RAM mapping The special function registers include the Indirect Addressing register 0 (00H), the Memory Pointer register 0 (MP0;01H), the Indirect Addressing register 1 (02H), the Memory Pointer register 1 (MP1;03H), the Accumulator Instruction(s) HT82K68E (ACC;05H), the Program Counter Lower-byte register (PCL;06H), the Table Pointer (TBLP;07H), the Table Higher-order byte register (TBLH;08H), the Watchdog Timer option Setting register (WDTS;09H), the Status register Table Location *11 *10 *9 *8 *7 *6 *5 *4 *3 *2 *1 *0 TABRDC [m] P11 P10 P9 P8 @7 @6 @5 @4 @3 @2 @1 @0 TABRDL [m] 1 0 1 1 @7 @6 @5 @4 @3 @2 @1 @0 Note: *11~*0: Table location bits @7~@0: Table location bits P11~P8: Current program counter bits 9 August 8, 2000 Preliminary (STATUS;0AH), the Interrupt Control register (INTC;0BH), the timer counter register (TMR;0DH), the timer counter control register (TMRC;0EH), the I/O registers (PA;12H, PB;14H, PC;16H, PD;18H, PE;1AH) and the I/O control registers (PAC;13H, PBC;15H, PCC;17H, PDC;19H, PEC;1BH). The remaining space before the 60H is reserved for future expanded usage and reading these locations will get the result 00H. The general purpose data memory, addressed from 60H to FFH, is used for data and control information under instruction command. HT82K68E Arithmetic and logic unit - ALU This circuit performs 8-bit arithmetic and logic operation. The ALU provides the following functions: · Arithmetic operations (ADD, ADC, SUB, SBC, DAA) · Logic operations (AND, OR, XOR, CPL) · Rotation (RL, RR, RLC, RRC) · Increment and Decrement (INC, DEC) · Branch decision (SZ, SNZ, SIZ, SDZ ....) The ALU not only saves the results of a data operation but also changes the status register. All data memory areas can handle arithmetic, logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the data memory can be set and reset by the SET [m].i and CLR [m].i instructions, respectively. They are also indirectly accessible through Memory pointer registers (MP0;01H, MP1;03H). Status register - Status The 8-bit status register (0AH) contains the zero flag (Z), carry flag (C), auxiliary carry flag (AC), overflow flag (OV), power down flag (PD) and watch dog time-out flag (TO). The status register not only records the status information but also controls the operation sequence. Indirect addressing register With the exception of the TO and PD flags, bits in the status register can be altered by instructions like most other registers. Any data written into the status register will not change the TO or PD flags. It should be noted that operations related to the status register may give different results from those intended. The TO and PD flags can only be changed by system power up, Watchdog Timer overflow, executing the HALT instruction and clearing the Watchdog Timer. Location 00H and 02H are indirect addressing registers that are not physically implemented. Any read/write operation of [00H] and [02H] can access the data memory pointed to by MP0 (01H) and MP1 (03H) respectively. Reading location 00H or 02H indirectly will return the result 00H. Writing indirectly results in no operation. The function of data movement between two indirect addressing registers is not supported. The memory pointer registers, MP0 and MP1, are 8-bit registers which can be used to access the data memory by combining corresponding indirect addressing registers. The Z, OV, AC and C flags generally reflect the status of the latest operations. In addition, on entering an interrupt sequence or executing a subroutine call, the status register will not be automatically pushed onto the stack. If the contents of status are important and if the subroutine can corrupt the status register, precaution must be taken to save it properly. Accumulator The accumulator is closely related to the ALU operations. It is also mapped to location 05H of the data memory and is capable of carrying out immediate data operations. The data movement between two data memory locations must pass through the accumulator. 10 August 8, 2000 Preliminary memory. Only the program counter is pushed onto the stack. If the contents of the register and Status register (STATUS) are altered by the interrupt service program which corrupt the desired control sequence, the contents should be saved in advance. Interrupt The HT82K68E provides an internal timer counter interrupt. The interrupt control register (INTC;0BH) contains the interrupt control bits to set not only the enable/disable status but also the interrupt request flags. The internal timer counter interrupt is initialized by setting the timer counter interrupt request flag (T0F; bit 5 of INTC), which is normally caused by a timer counter overflow. When the interrupt is enabled, and the stack is not full and the T0F bit is set, a subroutine call to location 08H will occur. The related interrupt request flag (T0F) will be reset and the EMI bit cleared to disable further interrupts. Once an interrupt subroutine is serviced, all other interrupts will be blocked (by clearing the EMI bit). This scheme may prevent any further interrupt nesting. Other interrupt requests may occur during this interval but only the interrupt request flag is recorded. If a certain interrupt requires servicing within the service routine, the EMI bit and the corresponding bit of the INTC may be set to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If immediate service is desired, the stack must be prevented from becoming full. During the execution of an interrupt subroutine, other interrupt acknowledgements are held until the RETI instruction is executed or the EMI bit and the related interrupt control bit are set to 1 (if the stack is not full). To return from the interrupt subroutine, a RET or RETI instruction may be invoked. RETI will set the EMI bit to enable an interrupt service, but RET will not. All these kinds of interrupt have the wake-up capability. As an interrupt is serviced, a control transfer occurs by pushing the program counter onto the stack followed by a branch to a subroutine at the specified location in the program Labels HT82K68E Interrupts occurring in the interval between the rising edges of two consecutive T2 pulses, Bits Function C 0 C is set if the operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. C is also affected by a rotate through carry instruction. AC 1 AC is set if the operation results in a carry out of the low nibbles in addition or if no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared. Z 2 Z is set if the result of an arithmetic or logic operation is zero; otherwise Z is cleared. OV 3 OV is set if the operation results in a carry into the highest-order bit but not a carry out of the highest-order bit, or vice versa; otherwise OV is cleared. PD 4 PD is cleared when either a system power-up or executing the CLR WDT instruction. PD is set by executing the HALT instruction. TO 5 TO is cleared by a system power-up or executing the CLR WDT or HALT instruction. TO is set by a WDT time-out. ¾ 6 Undefined, read as "0" ¾ 7 Undefined, read as "0" Status register 11 August 8, 2000 Preliminary will be serviced on the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests, the following table shows the priority that is applied. These can be masked by resetting the EMI bit. No. a Interrupt Source Timer counter overflow controlled, once the ²CALL subroutine² operates in the interrupt subroutine it will damage the original control sequence. Oscillator configuration There are two oscillator circuits in HT82K68E. VDD Vector 08H The timer counter interrupt request flag (T0F), enable timer counter bit (ET0I), and enable master interrupt bit (EMI) constitute an interrupt control register (INTC) which is located at 0BH in the data memory. EMI, ET0I, are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once the interrupt request flags (T0F) are set, they will remain in the INTC register until the interrupts are serviced or cleared by a software instruction. OSC1 INTC (0BH) OSC1 fSYS/4 (NMOS Open Drain Output) OSC2 OSC2 Crystal Oscillator RC Oscillator System oscillator Both are designed for system clocks; the RC oscillator and the Crystal oscillator, which are determined by mask options. No matter what oscillator type is selected, the signal provides the system clock. The HALT mode stops the system oscillator and resists the external signal to conserve power. It is suggested that a program does not use the ²CALL subroutine² within the interrupt subroutine. Because interrupts often occur in an unpredictable manner or need to be serviced immediately in some applications, if only one stack is left and enabling the interrupt is not well Register HT82K68E Bit No. Label Function 0 EMI 1 ¾ 2 ET0I 3 ¾ Undefined, read as "0" 4 ¾ Undefined, read as "0"; programming must be "0" 5 T0F 6 ¾ Undefined, read as "0" 7 ¾ Unused bit, read as "0" Controls the master (global) interrupt (1= enabled; 0= disabled) Undefined, read as "0"; programming must be "0" Controls the timer counter interrupt (1= enabled; 0= disabled) Internal timer counter request flag (1= active; 0= inactive) INTC register 12 August 8, 2000 Preliminary HT82K68E If an RC oscillator is used, an external resistor between OSC1 and VDD is needed and the resistance must range from 51kW to 1MW. The system clock, divided by 4, is available on OSC2, which can be used to synchronize external logic. The RC oscillator provides the most cost effective solution. However, the frequency of the oscillation may vary with VDD, temperature and the chip itself due to process variations. It is, therefore, not suitable for timing sensitive operations where accurate oscillator frequency is desired. time-out periods. If WS2, WS1, WS0 are all equal to 1, the division ratio is up to 1:128, and the maximum time-out period is 2.6 seconds. If the Crystal oscillator is used, a crystal across OSC1 and OSC2 is needed to provide the feedback and phase shift needed for oscillator, no other external components are needed. Instead of a crystal, the resonator can also be connected between OSC1 and OSC2 to get a frequency reference, but two external capacitors in OSC1 and OSC2 are required. If the device operates in a noisy environment, using the on-chip RC oscillator (WDT OSC) is strongly recommended, since the HALT will stop the system clock. If the WDT oscillator is disabled, the WDT clock may still come from the instruction clock and operate in the same manner except that in the HALT state the WDT may stop counting and lose its protecting purpose. In this situation the WDT logic can be restarted by external logic. The high nibble and bit 3 of the WDTS are reserved for user defined flags, which can be used to indicate some specified status. The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Even if the system enters the power down mode, the system clock is stopped, but the WDT oscillator still works for a period of approximately 78 ms. The WDT oscillator can be disabled by mask option to conserve power. Watchdog Timer - WDT WS2 WS1 WS0 Division Ratio 0 0 0 1:1 0 0 1 1:2 0 1 0 1:4 0 1 1 1:8 1 0 0 1:16 1 0 1 1:32 1 1 0 1:64 1 1 1 1:128 WDTS register The WDT clock source is implemented by a dedicated RC oscillator (WDT oscillator) or instruction clock (system clock divided by 4), decided by mask options. This timer is designed to prevent a software malfunction or sequence jumping to an unknown location with unpredictable results. The Watchdog Timer can be disabled by mask option. If the Watchdog Timer is disabled, all the executions related to the WDT results in no operation. The WDT overflow under normal operation will initialize ²chip reset² and set the status bit TO. An overflow in the HALT mode, initializes a ²warm reset² only when the PC and SP are reset to zero. To clear the contents of the WDT (including the WDT prescaler ), three methods are adopted; external reset (a low level to RESET), software instruction(s), or a HALT instruction. There are two types of software instructions; CLR WDT and CLR WDT1/CLR WDT2. Of these two types of instruction, only one can be active depending on the mask option - ²CLR WDT times selection option². If the ²CLR WDT² is selected (ie. CLR WDT times equal one), any execution of the CLR WDT instruction will clear the WDT. In case ²CLR WDT1² and ²CLR WDT2² are chosen (ie. CLRWDT times equal two), these two instructions must be exe- Once the internal WDT oscillator (RC oscillator normally with a period of 78ms) is selected, it is first divided by 256 (8-stages) to get the nominal time-out period of approximately 20 ms. This time-out period may vary with temperature, VDD and process variations. By invoking the WDT prescaler, longer time-out periods can be realized. Writing data to WS2, WS1, WS0 (bit 2,1,0 of the WDTS) can give different 13 August 8, 2000 Preliminary Once a wake-up event occurs, and the system clock comes from a crystal, it takes 1024 tSYS (system clock period) to resume normal operation. In other words, the HT82K68E will insert a dummy period after the wake-up. If the system clock comes from an RC oscillator, it continues operating immediately. If the wake-up results in next instruction execution, this will execute immediately after the dummy period is completed. cuted to clear the WDT; otherwise, the WDT may reset the chip because of the time-out. Power down operation - HALT The HALT mode is initialized by the HALT instruction and results in the following... · The system oscillator will turn off but the · · · · WDT oscillator keeps running (if the WDT oscillator is selected). The contents of the on chip RAM and registers remain unchanged. WDT and WDT prescaler will be cleared and recount again (if the WDT clock has come from the WDT oscillator). All I/O ports maintain their original status. The PD flag is set and the TO flag is cleared. To minimize power consumption, all I/O pins should be carefully managed before entering the HALT status. Reset There are three ways in which a reset can occur: · RESET reset during normal operation · RESET reset during HALT The system can leave the HALT mode by means of an external reset, an external falling edge signal on port A and port C [0:3] or a WDT overflow. An external reset causes a device initialization and the WDT overflow performs a ²warm reset². Examining the TO and PD flags, the reason for chip reset can be determined. The PD flag is cleared when system power-up or executing the CLR WDT instruction and is set when the HALT instruction is executed. The TO flag is set if the WDT time-out occurs, and causes a wake-up that only resets the PC and SP, the others keep their original status. V D D tS R E S E T S T S S T T im e - o u t C h ip R e s e t Reset timing chart · WDT time-out reset during normal operation The WDT time-out during HALT is different from other chip reset conditions, since it can perform a warm reset that just resets the PC and SP, leaving the other circuits to remain in their original state. Some registers remain unchanged during other reset conditions. Most registers are reset to the ²initial condition² The port A or port C [0:3] wake-up can be considered as a continuation of normal execution. Each bit in port A can be independently selected to wake up the device by mask option. Awakening from an I/O port stimulus, the program will resume execution of the next instruction. S y s te m HT82K68E c lo c k /4 W D T O S C R O M C o d e O p tio n S e le c t W D T P r e s c a le r 8 - b it C o u n te r 7 - b it C o u n te r 8 -to -1 M U X W S 0 ~ W S 2 W D T T im e - o u t Watchdog Timer 14 August 8, 2000 Preliminary V HT82K68E When a system power-up occurs, the SST delay is added during the reset period. But when the reset comes from the RESET pin, the SST delay is disabled. Any wake-up from HALT will enable the SST delay. D D R E S E T The functional unit chip reset status is shown below. Reset circuit when the reset conditions are met. By examining the PD and TO flags, the program can distinguish between different ²chip resets². TO PD RESET Conditions 0 0 RESET reset during power-up u u RESET reset during normal operation 0 1 RESET wake-up HALT 1 u WDT time-out during normal operation 1 1 WDT wake-up HALT W D T T im e - o u t R e s e t W a rm S S T 1 0 -s ta g e R ip p le C o u n te r Clear WDT Clear. After master reset, WDT begins counting Timer counter Off Points to the top of the stack Timer counter A timer counter (TMR) is implemented in the HT82K68E. The timer counter contains an 8-bit programmable count-up counter and the clock may come from the system clock divided by 4. Using the internal instruction clock, there is only one reference time-base. There are two registers related to the timer counter; TMR ([0DH]), TMRC ([0EH]). Two physical registers are mapped to TMR location; writing TMR makes the starting value be placed in the timer counter preload register and reading TMR gets the contents of the timer counter. The TMRC is a timer counter control register, which defines some options. R e s e t In the timer mode, once the timer counter starts counting, it will count from the current contents in the timer counter to FFH. Once overflow occurs, the counter is reloaded from the timer counter preload register and generates the interrupt request flag (TF; bit 5 of INTC) at the same time. R E S E T O S C 1 Prescaler SP To guarantee that the system oscillator has started and stabilized, the SST (System Start-up Timer) provides an extra-delay of 1024 system clock pulses when the system powers up or when it awakes from the HALT state. W D T 000H Input/output ports Input mode Note: ²u² means ²unchanged² H A L T PC C o ld R e s e t P o w e r - o n D e te c tio n Reset configuration 15 August 8, 2000 Preliminary To enable the counting operation, the timer ON bit (TON; bit 4 of TMRC) should be set to 1. In the case of timer counter OFF condition, writing data to the timer counter preload register will also reload that data to the timer counter. But if the timer counter is turned on, data written to it will only be kept in the timer counter preload register. The timer counter will still operate until overflow occurs. When the timer counter (reading TMR) is read, the clock will be blocked to avoid errors. As clock blocking may results in a counting error, this must be taken into consideration by the programmer. HT82K68E Input/output ports There are 32 bidirectional input/output lines in the HT82K68E, labeled from PA to PE, which are mapped to the data memory of [12H], [14H], [16H], [18H] and [1AH] respectively. All these I/O ports can be used for input and output operations. For input operation, these ports are non-latching, that is, the inputs must be ready at the T2 rising edge of instruction MOV A,[m] (m=12H, 14H, 16H, 18H or 1AH). For output operation, all data is latched and remains unchanged until the output latch is rewritten. Label Bits Function ¾ 0~3 TON 4 To enable/disable timer counting (0= disabled; 1= enabled) ¾ 5 Unused bits, read as "0" TM0 TM1 6 7 10= Timer mode (internal clock) Unused bits, read as "0" TMRC register S y s te m C lo c k /4 T M 1 T M 0 T O N D a ta B u s T M 1 T M 0 T im e r C o u n te r P r e lo a d R e g is te r T im e r C o u n te r P u ls e W id th M e a s u re m e n t M o d e C o n tro l R e lo a d O v e r flo w to In te rru p t Timer counter 16 August 8, 2000 Preliminary HT82K68E The state of the registers is summarized in the following table: WDT Time-out RESET Reset RESET Reset (Normal (Normal (HALT) Operation) Operation) WDT Time-out (HALT) Register Reset (Power On) TMR xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu TMRC 00-0 1--- 00-0 1--- 00-0 1--- 00-0 1--- uu-u u--- PC 000H 000H 000H 000H 000H* MP0 xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu MP1 xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ACC xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu TBLP xxxx xxxx uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu TBLH -xxx xxxx -uuu uuuu -uuu uuuu -uuu uuuu -uuu uuuu STATUS --00 xxxx --1u uuuu --uu uuuu --01 uuuu --11 uuuu INTC -000 0000 -000 0000 -000 0000 -000 0000 -uuu uuuu WDTS 0000 0111 0000 0111 0000 0111 0000 0111 uuuu uuuu PA 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PAC 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PB 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PBC 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PC 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PCC 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PD 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PDC 1111 1111 1111 1111 1111 1111 1111 1111 uuuu uuuu PE ---1 1111 ---1 1111 ---1 1111 ---1 1111 ---u uuuu PEC ---1 1111 ---1 1111 ---1 1111 ---1 1111 ---u uuuu Note: ²*² means warm reset ²u² means unchanged ²x² means unknown 17 August 8, 2000 Preliminary After a chip reset, these input/output lines stay at high levels or floating (mask option). Each bit of these input/output latches can be set or cleared by the SET [m].i or CLR [m].i (m=12H, 14H, 16H, 18H or 1AH) instruction. Each I/O line has its own control register (PAC, PBC, PCC, PDC, PEC) to control the input/output configuration. With this control register, CMOS output or schmitt trigger input with or without pull-high resistor (mask option) structures can be reconfigured dynamically (i.e., on-the-fly) under software control. To function as an input, the corresponding latch of the control register must write ²1². The pull-high resistance will exhibit automatically if the pull-high option is selected. The input source(s) also depend(s) on the control register. If the control register bit is ²1², input will read the pad state. If the control register bit is ²0², the contents of the latches will move to the internal bus. The latter is possible in ²read-modify-write² instruction. For output function, CMOS is the only configuration. These control registers are mapped to locations 13H, 15H, 17H, 19H and 1BH. D a ta B u s Some instructions first input data and then follow the output operations. For example, the SET [m].i, CLR [m].i, CPL [m] and CPLA [m] instructions read the entire port states into the CPU, execute the defined operations (bit-operation), and then write the results back to the latches or the accumulator. Each line of port A and port C [0:3] has the capability to wake-up the device. V D Q W r ite C o n tr o l R e g is te r C K Q S V C h ip R e s e t D W e a k P u ll- u p P A P B P C P D P E Q C K S Q M R e a d I/O S y s te m W a k e -u p ( P A & P C 0 ~ P C 3 o n ly ) D D D D R O M R e a d C o n tr o l R e g is te r W r ite I/O HT82K68E R O M U C o d e O p tio n 0 ~ P 0 ~ P 0 ~ P 0 ~ P 0 ~ P A 7 B 7 C 7 D 7 E 4 X C o d e O p tio n Input/output ports 18 August 8, 2000 Preliminary HT82K68E ROM code option The following shows six kinds of ROM code option in the HT82K68E. All the ROM code options must be defined to ensure proper system function. No. ROM Code Option 1 OSC type selection. This option is to decide if an RC or Crystal oscillator is chosen as system clock. If the Crystal oscillator is selected, the XST (Crystal Start-up Timer) default is activated, otherwise the XST is disabled. 2 WDT source selection. There are three types of selection: on-chip RC oscillator, instruction clock or disable the WDT. 3 CLRWDT times selection. This option defines the way to clear the WDT by instruction. ²One time² means that the CLR WDT instruction can clear the WDT. ²Two times² means only if both of the CLR WDT1 and CLR WDT2 instructions have been executed, only then will the WDT be cleared. 4 Wake-up selection. This option defines the wake-up function activity. External I/O pins (PA and PC [0:3] only) all have the capability to wake-up the chip from a HALT. 5 Pull-high selection. This option is to decide whether the pull-high resistance is visible or not in the input mode of the I/O ports. Each bit of an I/O port can be independently selected. 6 Special power on reset. This option defines the function will reset the chip to prevent incorrect status. If the special power on reset is enabled, the chip must not enter the HALT mode. 19 August 8, 2000 Preliminary HT82K68E Application Circuits R C V o s c illa to r fo r m u ltip le I/O D D F .B . a p p lic a tio n s V D D 1 0 m F 0 .1 m F V fS Y S /4 (N M O S O p e n D r a in O u tp u t) D D O S C 1 V O S C 2 D D V R E S E T D D P E 2 P E 3 P E 4 P C 0 P C 1 C r y s ta l o s c illa to r o r c e r a m ic r e s o n a to r fo r m u ltip le I/O a p p lic a tio n s V P A 0 P A 1 P A 2 P A 3 P A 4 P A 5 P A 6 P A 7 P B 0 P B 1 P B 2 P B 3 P B 4 P B 5 P B 6 P B 7 P D 0 P D 1 P D 2 P D 3 P D 4 P D 5 P D 6 P D 7 P C 2 P C 3 P C 4 P C 5 P C 6 P C 7 P E 0 P E 1 D D F .B . P A 0 P A 1 P A 2 P A 3 P A 4 P A 5 P A 6 P A 7 P B 0 P B 1 P B 2 P B 3 P B 4 P B 5 P B 6 P B 7 P D 0 P D 1 P D 2 P D 3 P D 4 P D 5 P D 6 P D 7 P C 2 P C 3 P C 4 P C 5 P C 6 P C 7 P E 0 P E 1 V D D 1 0 m F 0 .1 m F R e s e rv e fo r R e s o n a to r O S C 1 O S C 2 V D D R E S E T V D D P E 2 P E 3 P E 4 P C 0 P C 1 H T 8 2 K 6 8 E H T 8 2 K 6 8 E 20 August 8, 2000 Preliminary HT82K68E Instruction Set Summary Mnemonic Description Flag Affected Add data memory to ACC Add ACC to data memory Add immediate data to ACC Add data memory to ACC with carry Add ACC to register with carry Subtract immediate data from ACC Subtract data memory from ACC Subtract data memory from ACC with result in data memory Subtract data memory from ACC with carry Subtract data memory from ACC with carry with result in data memory Decimal adjust ACC for addition with result in data memory Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Arithmetic ADD A,[m] ADDM A,[m] ADD A,x ADC A,[m] ADCM A,[m] SUB A,x SUB A,[m] SUBM A,[m] SBC A,[m] SBCM A,[m] DAA [m] C Logic Operation AND A,[m] OR A,[m] XOR A,[m] ANDM A,[m] ORM A,[m] XORM A,[m] AND A,x OR A,x XOR A,x CPL [m] CPLA [m] AND data memory to ACC OR data memory to ACC Exclusive-OR data memory to ACC AND ACC to data memory OR ACC to data memory Exclusive-OR ACC to data memory AND immediate data to ACC OR immediate data to ACC Exclusive-OR immediate data to ACC Complement data memory Complement data memory with result in ACC Z Z Z Z Z Z Z Z Z Z Z Increment & Decrement INCA [m] INC [m] DECA [m] DEC [m] Increment data memory with result in ACC Increment data memory Decrement data memory with result in ACC Decrement data memory Z Z Z Z Rotate RRA [m] RR [m] RRCA [m] RRC [m] RLA [m] RL [m] RLCA [m] RLC [m] Rotate data memory right with result in ACC Rotate data memory right Rotate data memory right through carry with result in ACC Rotate data memory right through carry Rotate data memory left with result in ACC Rotate data memory left Rotate data memory left through carry with result in ACC Rotate data memory left through carry 21 None C C None None C C August 8, 2000 Preliminary Mnemonic Description HT82K68E Flag Affected Data Move MOV A,[m] MOV [m],A MOV A,x Move data memory to ACC Move ACC to data memory Move immediate data to ACC None None None Clear bit of data memory Set bit of data memory None None Jump unconditional Skip if data memory is zero Skip if data memory is zero with data movement to ACC Skip if bit i of data memory is zero Skip if bit i of data memory is not zero Skip if increment data memory is zero Skip if decrement data memory is zero Skip if increment data memory is zero with result in ACC Skip if decrement data memory is zero with result in ACC Subroutine call Return from subroutine Return from subroutine and load immediate data to ACC Return from interrupt None None None None None None None None None None None None None Read ROM code (current page) to data memory and TBLH Read ROM code (last page) to data memory and TBLH None None Bit Operation CLR [m].i SET [m].i Branch JMP addr SZ [m] SZA [m] SZ [m].i SNZ [m].i SIZ [m] SDZ [m] SIZA [m] SDZA [m] CALL addr RET RET A,x RETI Table Read TABRDC [m] TABRDL [m] Miscellaneous NOP CLR [m] SET [m] CLR WDT CLR WDT1 CLR WDT2 SWAP [m] SWAPA [m] HALT No operation Clear data memory Set data memory Clear Watchdog Timer Pre-clear Watchdog Timer Pre-clear Watchdog Timer Swap nibbles of data memory Swap nibbles of data memory with result in ACC Enter power down mode Note: x: 8-bit immediate data None None None TO,PD TO*,PD* TO*,PD* None None TO,PD m: 7-bit data memory address A: Accumulator i: 0~7 number of bits addr: 12 bits program memory address Ö: 0~7 number of bits -: Flag(s) is not affected *: Flag(s) may be affected by the execution status 22 August 8, 2000 Preliminary HT82K68E Instruction Definition ADC A,[m] Add data memory and carry to the accumulator Description The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator. Operation ACC ¬ ACC+[m]+C Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö ADCM A,[m] Add the accumulator and carry to data memory Description The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory. Operation [m] ¬ ACC+[m]+C Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö ADD A,[m] Add data memory to the accumulator Description The contents of the specified data memory and the accumulator are added. The result is stored in the accumulator. Operation ACC ¬ ACC+[m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö ADD A,x Add immediate data to the accumulator Description The contents of the accumulator and the specified data are added, leaving the result in the accumulator. Operation ACC ¬ ACC+x Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö 23 August 8, 2000 Preliminary HT82K68E ADDM A,[m] Add the accumulator to the data memory Description The contents of the specified data memory and the accumulator are added. The result is stored in the data memory. Operation [m] ¬ ACC+[m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö AND A,[m] Logical AND accumulator with data memory Description Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator. Operation ACC ¬ ACC ²AND² [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ AND A,x Logical AND immediate data to the accumulator Description Data in the accumulator and the specified data perform a bitwise logical_AND operation. The result is stored in the accumulator. Operation ACC ¬ ACC ²AND² x Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ ANDM A,[m] Logical AND data memory with the accumulator Description Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory. Operation [m] ¬ ACC ²AND² [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ 24 August 8, 2000 Preliminary HT82K68E CALL addr Subroutine call Description The instruction unconditionally calls a subroutine located at the indicated address. The program counter increments once to obtain the address of the next instruction, and pushes this onto the stack. The indicated address is then loaded. Program execution continues with the instruction at this address. Operation Stack ¬ PC+1 PC ¬ addr Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ CLR [m] Clear data memory Description The contents of the specified data memory are cleared to zero. Operation [m] ¬ 00H Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ CLR [m].i Clear bit of data memory Description The bit i of the specified data memory is cleared to zero. Operation [m].i ¬ 0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ CLR WDT Clear Watchdog Timer Description The WDT and the WDT Prescaler are cleared (re-counting from zero). The power down bit (PD) and time-out bit (TO) are cleared. Operation WDT and WDT Prescaler ¬ 00H PD and TO ¬ 0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ 0 0 ¾ ¾ ¾ ¾ 25 August 8, 2000 Preliminary HT82K68E CLR WDT1 Preclear Watchdog Timer Description The TD, PD flags, WDT and the WDT Prescaler has cleared (re-counting from zero), if the other preclear WDT instruction has been executed. Only execution of this instruction without the other preclear instruction sets the indicated flag which implies that this instruction has been executed and the TO and PD flags remain unchanged. Operation WDT and WDT Prescaler ¬ 00H* PD and TO ¬ 0* Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ 0* 0* ¾ ¾ ¾ ¾ CLR WDT2 Preclear Watchdog Timer Description The TO, PD flags, WDT and the WDT Prescaler are cleared (re-counting from zero), if the other preclear WDT instruction has been executed. Only execution of this instruction without the other preclear instruction sets the indicated flag which implies that this instruction has been executed and the TO and PD flags remain unchanged. Operation WDT and WDT Prescaler ¬ 00H* PD and TO ¬ 0* Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ 0* 0* ¾ ¾ ¾ ¾ CPL [m] Complement data memory Description Each bit of the specified data memory is logically complemented (1¢s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. Operation [m] ¬ [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ 26 August 8, 2000 Preliminary HT82K68E CPLA [m] Complement data memory and place result in the accumulator Description Each bit of the specified data memory is logically complemented (1¢s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. The complemented result is stored in the accumulator and the contents of the data memory remain unchanged. Operation ACC ¬ [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ DAA [m] Decimal-Adjust accumulator for addition Description The accumulator value is adjusted to the BCD (Binary Code Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored in the data memory and only the carry flag (C) may be affected. Operation If ACC.3~ACC.0 >9 or AC=1 then [m].3~[m].0 ¬ (ACC.3~ACC.0)+6, AC1=AC else [m].3~[m].0) ¬ (ACC.3~ACC.0), AC1=0 and If ACC.7~ACC.4+AC1 >9 or C=1 then [m].7~[m].4 ¬ ACC.7~ACC.4+6+AC1,C=1 else [m].7~[m].4 ¬ ACC.7~ACC.4+AC1,C=C Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ Ö DEC [m] Decrement data memory Description Data in the specified data memory is decremented by1. Operation [m] ¬ [m] 1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ 27 August 8, 2000 Preliminary HT82K68E DECA [m] Decrement data memory and place result in the accumulator Description Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. Operation ACC ¬ [m] 1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ HALT Enter power down mode Description This instruction stops program execution and turns off the system clock. The contents of the RAM and registers are retained. The WDT and prescaler are cleared. The power down bit (PD) is set and the WDT time-out bit (TO) is cleared. Operation PC ¬ PC+1 PD ¬ 1 TO ¬ 0 Affected flag(s) INC [m] TC2 TC1 TO PD OV Z AC C ¾ ¾ 0 1 ¾ ¾ ¾ ¾ Increment data memory Description Data in the specified data memory is incremented by 1. Operation [m] ¬ [m]+1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ INCA [m] Increment data memory and place result in the accumulator Description Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. Operation ACC ¬ [m]+1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ 28 August 8, 2000 Preliminary HT82K68E JMP addr Directly jump Description The contents of the program counter are replaced with the directly-specified address unconditionally, and control is passed to this destination. Operation PC ¬ addr Affected flag(s) MOV A,[m] TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ Move data memory to the accumulator Description The contents of the specified data memory are copied to the accumulator. Operation ACC ¬ [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ MOV A,x Move immediate data to the accumulator Description The 8-bit data specified by the code is loaded into the accumulator. Operation ACC ¬ x Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ MOV [m],A Move the accumulator to data memory Description The contents of the accumulator are copied to the specified data memory (one of the data memories). Operation [m] ¬ ACC Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ NOP No operation Description No operation is performed. Execution continues with the next instruction. Operation PC ¬ PC+1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 29 August 8, 2000 Preliminary HT82K68E OR A,[m] Logical OR accumulator with data memory Description Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator. Operation ACC ¬ ACC ²OR² [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ OR A,x Logical OR immediate data to the accumulator Description Data in the accumulator and the specified data perform a bitwise logical_OR operation. The result is stored in the accumulator. Operation ACC ¬ ACC ²OR² x Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ ORM A,[m] Logical OR data memory with the accumulator Description Data in the data memory (one of the data memories) and the accumulator perform a bitwise logical_OR operation. The result is stored in the data memory. Operation [m] ¬ ACC ²OR² [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ RET Return from subroutine Description The program counter is restored from the stack. This is a two-cycle instruction. Operation PC ¬ Stack Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 30 August 8, 2000 Preliminary HT82K68E RET A,x Return and place immediate data in the accumulator Description The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data. Operation PC ¬ Stack ACC ¬ x Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ RETI Return from interrupt Description The program counter is restored from the stack, and interrupts are enabled by setting the EMI bit. EMI is the enable master (global) interrupt bit (bit 0; register INTC). Operation PC ¬ Stack EMI ¬ 1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ RL [m] Rotate data memory left Description The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0. Operation [m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 ¬ [m].7 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ RLA [m] Rotate data memory left and place result in the accumulator Description Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. Operation ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 ¬ [m].7 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 31 August 8, 2000 Preliminary HT82K68E RLC [m] Rotate data memory left through carry Description The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position. Operation [m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 ¬ C C ¬ [m].7 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ Ö RLCA [m] Rotate left through carry and place result in the accumulator Description Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored in the accumulator but the contents of the data memory remain unchanged. Operation ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 ¬ C C ¬ [m].7 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ Ö RR [m] Rotate data memory right Description The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7. Operation [m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 ¬ [m].0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 32 August 8, 2000 Preliminary HT82K68E RRA [m] Rotate right-place result in the accumulator Description Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. Operation ACC.(i) ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 ¬ [m].0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ RRC [m] Rotate data memory right through carry Description The contents of the specified data memory and the carry flag are together rotated 1 bit right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position. Operation [m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 ¬ C C ¬ [m].0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ Ö RRCA [m] Rotate right through carry - place result in the accumulator Description Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is stored in the accumulator. The contents of the data memory remain unchanged. Operation ACC.i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 ¬ C C ¬ [m].0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ Ö 33 August 8, 2000 Preliminary HT82K68E SBC A,[m] Subtract data memory and carry from the accumulator Description The contents of the specified data memory and the complement of the carry flag aresubtractedfromtheaccumulator, leaving the result in the accumulator. Operation ACC ¬ ACC+[m]+C Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö SBCM A,[m] Subtract data memory and carry from the accumulator Description The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory. Operation [m] ¬ ACC+[m]+C Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö SDZ [m] Skip if decrement data memory is 0 Description The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (two cycles). Otherwise proceed with the next instruction (one cycle). Operation Skip if ([m]-1)=0, [m] ¬ ([m]-1) Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SDZA [m] Decrement data memory and place result in ACC, skip if 0 Description The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. The result is stored in the accumulator but the data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Operation Skip if ([m]-1)=0, ACC ¬ ([m]-1) Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 34 August 8, 2000 Preliminary HT82K68E SET [m] Set data memory Description Each bit of the specified data memory is set to 1. Operation [m] ¬ FFH Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SET [m].i Set bit of data memory Description Bit ²i² of the specified data memory is set to 1. Operation [m].i ¬ 1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SIZ [m] Skip if increment data memory is zero Description The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Operation Skip if ([m]+1)=0, [m] ¬ ([m]+1) Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SIZA [m] Increment data memory and place result in ACC, skip if 0 Description The contents of the specified data memory are incremented by 1. If the result is zero, the next instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Operation Skip if ([m]+1)=0, ACC ¬ ([m]+1) Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 35 August 8, 2000 Preliminary HT82K68E SNZ [m].i Skip if bit ²i² of the data memory is not 0 Description If bit ²i² of the specified data memory is not zero, the next instruction is skipped. If bit ²i² of the data memory is not 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Operation Skip if [m].i¹0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SUB A,[m] Subtract data memory from the accumulator Description The specified data memory is subtracted from the contents of the accumulator, leaving the result in the accumulator. Operation ACC ¬ ACC+[m]+1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö SUBM A,[m] Subtract data memory from the accumulator Description The specified data memory is subtracted from the contents of the accumulator, leaving the result in the data memory. Operation [m] ¬ ACC+[m]+1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö SUB A,x Subtract immediate data from the accumulator Description The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator. Operation ACC ¬ ACC+x+1 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ Ö Ö Ö Ö 36 August 8, 2000 Preliminary HT82K68E SWAP [m] Swap nibbles within the data memory Description The low-order and high-order nibbles of the specified data memory (one of the data memories) are interchanged. Operation [m].3~[m].0 « [m].7~[m].4 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SWAPA [m] Swap data memory-place result in the accumulator Description The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged. Operation ACC.3~ACC.0 ¬ [m].7~[m].4 ACC.7~ACC.4 ¬ [m].3~[m].0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SZ [m] Skip if data memory is 0 Description If the contents of the specified data memory are 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (2 cycle). Operation Skip if [m]=0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ SZA [m] Move data memory to ACC, skip if 0 Description The contents of the specified data memory are copied to the accumulator. If the contents is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Operation Skip if [m]=0, ACC ¬ [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ 37 August 8, 2000 Preliminary HT82K68E SZ [m].i Skip if bit ²i² of the data memory is zero Description If bit ²i² of the specified data memory is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Operation Skip if [m].i=0 Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ TABRDC [m] Move the ROM code (current page) to TBLH and data memory Description The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved to the specified data memory and the high byte transferred to TBLH directly. Operation [m] ¬ ROM code (low byte) TBLH ¬ ROM code (high byte) Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ TABRDL [m] Move the ROM code (last page) to TBLH and data memory Description The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to the data memory and the high byte transferred to TBLH directly. Operation [m] ¬ ROM code (low byte) TBLH ¬ ROM code (high byte) Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ ¾ ¾ ¾ XOR A,[m] Logical XOR accumulator with data memory Description Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator. Operation ACC ¬ ACC ²XOR² [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ 38 August 8, 2000 Preliminary HT82K68E XORM A,[m] Logical XOR data memory with the accumulator Description Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected. Operation [m] ¬ ACC ²XOR² [m] Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ XOR A,x Logical XOR immediate data to the accumulator Description Data in the the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected. Operation ACC ¬ ACC ²XOR² x Affected flag(s) TC2 TC1 TO PD OV Z AC C ¾ ¾ ¾ ¾ ¾ Ö ¾ ¾ 39 August 8, 2000 Preliminary HT82K68E Holtek Semiconductor Inc. (Headquarters) No.3 Creation Rd. II, Science-based Industrial Park, Hsinchu, Taiwan, R.O.C. Tel: 886-3-563-1999 Fax: 886-3-563-1189 Holtek Semiconductor Inc. (Taipei Office) 5F, No.576, Sec.7 Chung Hsiao E. Rd., Taipei, Taiwan, R.O.C. Tel: 886-2-2782-9635 Fax: 886-2-2782-9636 Fax: 886-2-2782-7128 (International sales hotline) Holtek Semiconductor (Hong Kong) Ltd. RM.711, Tower 2, Cheung Sha Wan Plaza, 833 Cheung Sha Wan Rd., Kowloon, Hong Kong Tel: 852-2-745-8288 Fax: 852-2-742-8657 Copyright Ó 2000 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw. 40 August 8, 2000