SN74AUC2G125 DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS www.ti.com SCES532D – DECEMBER 2003 – REVISED AUGUST 2007 FEATURES • • • • • Available in the Texas Instruments NanoFree™ Package Optimized for 1.8-V Operation and Is 3.6-V I/O Tolerant to Support Mixed-Mode Signal Operation Ioff Supports Partial-Power-Down Mode Operation Sub-1-V Operable Max tpd of 1.8 ns at 1.8 V DCT PACKAGE (TOP VIEW) • • • Low Power Consumption, 10 μA at 1.8 V ±8-mA Output Drive at 1.8 V Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 – 2000-V Human-Body Model (A114-A) – 200-V Machine Model (A115-A) – 1000-V Charged-Device Model (C101) • DCU PACKAGE (TOP VIEW) 1OE 1 8 VCC 1A 2 7 2OE 2Y 3 6 1Y GND 4 5 2A 1OE 1A 2Y GND 1 2 3 8 7 6 4 5 YZP PACKAGE (BOTTOM VIEW) VCC 2OE 1Y 2A GND 2Y 1A 1OE 4 5 3 6 2 7 1 8 2A 1Y 2OE VCC See mechanical drawings for dimensions. DESCRIPTION/ORDERING INFORMATION This dual bus buffer gate is operational at 0.8-V to 2.7-V VCC, but is designed specifically for 1.65-V to 1.95-V VCC operation. The SN74AUC2G125 features dual line drivers with 3-state outputs. The outputs are disabled when the associated output-enable (OE) input is high. NanoFree™ package technology is a major breakthrough in IC packaging concepts, using the die as the package. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION TA –40°C to 85°C (1) (2) (3) PACKAGE (1) (2) ORDERABLE PART NUMBER TOP-SIDE MARKING (3) NanoFree™ – WCSP (DSBGA) Reel of 3000 0.23-mm Large Bump – YZP (Pb-free) SN74AUC2G125YZPR _ _ _UM_ SSOP – DCT Reel of 3000 SN74AUC2G125DCTR U25_ _ _ VSSOP – DCU Reel of 3000 SN74AUC2G125DCUR U25_ Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. DCT: The actual top-side marking has three additional characters that designate the year, month, and assembly/test site. DCU: The actual top-side marking has one additional character that designates the assembly/test site. YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following character to designate the assembly/test site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free). Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. NanoFree is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2007, Texas Instruments Incorporated SN74AUC2G125 DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS www.ti.com SCES532D – DECEMBER 2003 – REVISED AUGUST 2007 DESCRIPTION/ORDERING INFORMATION (CONTINUED) This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. For more information about AUC Little Logic devices, please refer to the TI application report, Applications of Texas Instruments AUC Sub-1-V Little Logic Devices, literature number SCEA027. FUNCTION TABLE (EACH BUFFER) INPUTS OE A OUTPUT Y L H H L L L H X Z LOGIC DIAGRAM (POSITIVE LOGIC) 1 1OE 1A 2 6 1Y 7 2OE 5 3 2A 2 2Y Submit Documentation Feedback SN74AUC2G125 DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS www.ti.com SCES532D – DECEMBER 2003 – REVISED AUGUST 2007 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 3.6 V VI Input voltage range (2) –0.5 3.6 V –0.5 3.6 V –0.5 VCC + 0.5 (2) UNIT VO Voltage range applied to any output in the high-impedance or power-off state VO Output voltage range (2) IIK Input clamp current VI < 0 –50 mA IOK Output clamp current VO < 0 –50 mA IO Continuous output current ±20 mA ±100 mA Continuous current through VCC or GND Package thermal impedance (3) θJA Tstg (1) (2) (3) DCT package 220 DCU package 227 YZP package 102 Storage temperature range –65 V °C/W °C 150 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input negative-voltage and output voltage ratings may be exceeded if the input and output current ratings are observed. The package thermal impedance is calculated in accordance with JESD 51-7. Recommended Operating Conditions (1) VCC Supply voltage VCC = 0.8 V VIH High-level input voltage MIN MAX 0.8 2.7 0.65 × VCC VCC = 1.1 V to 1.95 V 0 0.35 × VCC VCC = 1.1 V to 1.95 V VCC = 2.3 V to 2.7 V VI Output voltage IOH High-level output current IOL Low-level output current 0 3.6 Active state 0 VCC 3-state 0 3.6 VCC = 0.8 V –0.7 VCC = 1.1 V –3 VCC = 1.4 V –5 VCC = 1.65 V –8 VCC = 2.3 V –9 VCC = 0.8 V 0.7 VCC = 1.1 V 3 VCC = 1.4 V 5 VCC = 1.65 V 8 VCC = 2.3 V VCC = 0.8 V to 1.65 V ∆t/∆v TA (1) (2) (3) Input transition rise or fall rate V V mA mA 9 (2) 20 VCC = 1.65 V to 1.95 V (3) 20 VCC = 2.3 V to 2.7 V (3) 15 Operating free-air temperature V 0.7 Input voltage VO V 1.7 VCC = 0.8 V Low-level input voltage V VCC VCC = 2.3 V to 2.7 V VIL UNIT –40 85 ns/V °C All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. The data was taken at CL = 15 pF, RL = 2 kΩ (see Figure 1). The data was taken at CL = 30 pF, RL = 500 Ω (see Figure 1). Submit Documentation Feedback 3 SN74AUC2G125 DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS www.ti.com SCES532D – DECEMBER 2003 – REVISED AUGUST 2007 Electrical Characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS VOH VOL VCC TYP (1) MIN MAX IOH = –100 μA 0.8 V to 2.7 V IOH = –0.7 mA 0.8 V IOH = –3 mA 1.1 V 0.8 IOH = –5 mA 1.4 V 1 IOH = –8 mA 1.65 V 1.2 IOH = –9 mA 2.3 V 1.8 IOL = 100 μA 0.8 V to 2.7 V IOL = 0.7 mA 0.8 V IOL = 3 mA 1.1 V 0.3 IOL = 5 mA 1.4 V 0.4 IOL = 8 mA 1.65 V 0.45 IOL = 9 mA 2.3 V 0.6 UNIT VCC – 0.1 0.55 V 0.2 0.25 V VI = VCC or GND 0 to 2.7 V ±5 μA Ioff VI or VO = 2.7 V 0 ±10 μA IOZ VO = VCC or GND 2.7 V ±10 μA ICC VI = VCC or GND, 10 μA Ci VI = VCC or GND 2.5 V 2.5 pF Co VO = VCC or GND 2.5 V 5.5 pF II (1) A or OE inputs IO = 0 0.8 V to 2.7 V All typical values are at TA = 25°C. Switching Characteristics over recommended operating free-air temperature range, CL = 15 pF (unless otherwise noted) (see Figure 1) VCC = 1.2 V ± 0.1 V VCC = 1.5 V ± 0.1 V VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V FROM (INPUT) TO (OUTPUT) VCC = 0.8 V TYP MIN MAX MIN MAX MIN TYP MAX MIN MAX tpd A Y 5.1 1 3.6 0.7 2.3 0.6 1 1.8 0.5 1.3 ns ten OE Y 5.9 1.1 4.1 1 2.6 0.9 1.3 2 0.8 1.5 ns tdis OE Y 6.6 2 4.8 1.5 3.5 1.8 2.6 3.7 1.4 2.9 ns PARAMETER UNIT Switching Characteristics over recommended operating free-air temperature range, CL = 30 pF (unless otherwise noted) (see Figure 1) FROM (INPUT) TO (OUTPUT) tpd A ten OE tdis OE PARAMETER 4 VCC = 1.8 V ± 0.15 V VCC = 2.5 V ± 0.2 V UNIT MIN TYP MAX MIN MAX Y 0.8 1.6 2.6 0.7 1.8 ns Y 1.1 1.7 2.9 0.9 2.2 ns Y 1.7 2.3 3.6 0.8 2 ns Submit Documentation Feedback SN74AUC2G125 DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS www.ti.com SCES532D – DECEMBER 2003 – REVISED AUGUST 2007 Operating Characteristics TA = 25°C PARAMETER Cpd Power dissipation capacitance TEST CONDITIONS VCC = 0.8 V VCC = 1.2 V VCC = 1.5 V VCC = 1.8 V VCC = 2.5 V TYP TYP TYP TYP TYP f = 10 MHz 16 16 16 17 18 Submit Documentation Feedback UNIT pF 5 SN74AUC2G125 DUAL BUS BUFFER GATE WITH 3-STATE OUTPUTS www.ti.com SCES532D – DECEMBER 2003 – REVISED AUGUST 2007 PARAMETER MEASUREMENT INFORMATION TEST tPLH/tPHL tPLZ/tPZL tPHZ/tPZH 2 × VCC S1 RL From Output Under Test Open S1 Open 2 × VCC GND GND CL (see Note A) RL LOAD CIRCUIT VCC CL RL VD 0.8 V 1.2 V ± 0.1 V 1.5 V ± 0.1 V 1.8 V ± 0.15 V 2.5 V ± 0.2 V 1.8 V ± 0.15 V 2.5 V ± 0.2 V 15 pF 15 pF 15 pF 15 pF 15 pF 30 pF 30 pF 2 kW 2 kW 2 kW 2 kW 2 kW 1 kW 500 W 0.1 V 0.1 V 0.1 V 0.15 V 0.15 V 0.15 V 0.15 V VCC Timing Input VCC/2 0V tW tsu VCC Input VCC/2 VCC/2 th VCC Data Input VCC/2 VCC/2 0V 0V VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VOLTAGE WAVEFORMS PULSE DURATION VCC VCC/2 Input VCC/2 0V tPLH VOH VCC/2 VOL tPHL VCC/2 tPLZ VCC VCC/2 tPZH VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS Output Waveform 2 S1 at GND (see Note B) VCC/2 0V Output Waveform 1 S1 at 2 × VCC (see Note B) tPLH VOH Output VCC/2 tPZL tPHL VCC/2 Output VCC Output Control VOL + VD VOL tPHZ VCC/2 VOH – VD VOH »0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR £ 10 MHz, ZO = 50 W, slew rate ³ 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. Figure 1. Load Circuit and Voltage Waveforms 6 Submit Documentation Feedback PACKAGE OPTION ADDENDUM www.ti.com 22-Jul-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty 74AUC2G125DCTRE4 ACTIVE SM8 DCT 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AUC2G125DCURE4 ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM 74AUC2G125DCURG4 ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AUC2G125DCTR ACTIVE SM8 DCT 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AUC2G125DCUR ACTIVE US8 DCU 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM SN74AUC2G125YZPR ACTIVE DSBGA YZP 8 3000 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 5-Aug-2009 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SN74AUC2G125DCUR US8 DCU 8 3000 180.0 9.2 2.25 3.35 1.05 4.0 8.0 Q3 SN74AUC2G125YZPR DSBGA YZP 8 3000 180.0 8.4 1.02 2.02 0.63 4.0 8.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 5-Aug-2009 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) SN74AUC2G125DCUR US8 DCU 8 3000 202.0 201.0 28.0 SN74AUC2G125YZPR DSBGA YZP 8 3000 220.0 220.0 34.0 Pack Materials-Page 2 MECHANICAL DATA MPDS049B – MAY 1999 – REVISED OCTOBER 2002 DCT (R-PDSO-G8) PLASTIC SMALL-OUTLINE PACKAGE 0,30 0,15 0,65 8 0,13 M 5 0,15 NOM ÇÇÇÇÇ ÇÇÇÇÇ ÇÇÇÇÇ ÇÇÇÇÇ 2,90 2,70 4,25 3,75 Gage Plane PIN 1 INDEX AREA 1 0,25 4 0° – 8° 3,15 2,75 0,60 0,20 1,30 MAX Seating Plane 0,10 0,10 0,00 NOTES: A. B. C. D. 4188781/C 09/02 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion Falls within JEDEC MO-187 variation DA. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated