TI XIO2213BZAY

XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
Data Manual
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Literature Number: SCPS210D
October 2008 – Revised July 2009
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Contents
1
Introduction ....................................................................................................................... 13
2
Overview ........................................................................................................................... 14
1.1
2.1
2.2
2.3
2.4
2.5
2.6
3
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
3.10
3.11
14
16
16
16
17
25
Power-Up/Power-Down Sequencing.....................................................................................
3.1.1
Power-Up Sequence ............................................................................................
3.1.2
Power-Down Sequence.........................................................................................
XIO2213B Reset Features ................................................................................................
PCI Express (PCIe) Interface .............................................................................................
3.3.1
External Reference Clock ......................................................................................
3.3.2
Beacon and Wake ...............................................................................................
3.3.3
Initial Flow Control Credits .....................................................................................
3.3.4
PCIe Message Transactions ...................................................................................
PCI Interrupt Conversion to PCIe Messages ...........................................................................
Two-Wire Serial-Bus Interface ............................................................................................
3.5.1
Serial-Bus Interface Implementation ..........................................................................
3.5.2
Serial-Bus Interface Protocol...................................................................................
3.5.3
Serial-Bus EEPROM Application ..............................................................................
3.5.4
Accessing Serial-Bus Devices Through Softwaree .........................................................
Advanced Error Reporting Registers ....................................................................................
Data Error Forwarding Capability ........................................................................................
General-Purpose I/O (GPIO) Interface ..................................................................................
Set Slot Power Limit Functionality .......................................................................................
PCIe and PCI Bus Power Management .................................................................................
1394b OHCI Controller Functionality ....................................................................................
3.11.1 1394b OHCI Power Management .............................................................................
3.11.2 1394b OHCI and VAUX ..........................................................................................
3.11.3 1394b OHCI and Reset Options ...............................................................................
3.11.4 1394b OHCI PCI Bus Master ..................................................................................
3.11.5 1394b OHCI Subsystem Identification ........................................................................
3.11.6 1394b OHCI PME Support .....................................................................................
32
33
34
35
36
36
36
36
37
38
39
39
40
42
44
44
44
45
45
45
47
47
47
47
47
48
48
Classic PCI Configuration Space .......................................................................................... 49
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
2
Description ..................................................................................................................
Related Documents ........................................................................................................
Documents Conventions ..................................................................................................
Ordering Information .......................................................................................................
Terminal Assignments .....................................................................................................
Terminal Descriptions ......................................................................................................
Feature/Protocol Descriptions.............................................................................................. 32
3.1
4
XIO2213B Features ........................................................................................................ 13
Vendor ID Register .........................................................................................................
Device ID Register .........................................................................................................
Command Register ........................................................................................................
Status Register .............................................................................................................
Class Code and Revision ID Register ...................................................................................
Cache Line Size Register .................................................................................................
Primary Latency Timer Register ..........................................................................................
Header Type Register .....................................................................................................
BIST Register ...............................................................................................................
Device Control Base Address Register .................................................................................
Scratchpad RAM Base Address ..........................................................................................
Primary Bus Number Register ............................................................................................
Contents
50
50
50
52
53
53
53
54
54
54
55
55
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
4.21
4.22
4.23
4.24
4.25
4.26
4.27
4.28
4.29
4.30
4.31
4.32
4.33
4.34
4.35
4.36
4.37
4.38
4.39
4.40
4.41
4.42
4.43
4.44
4.45
4.46
4.47
4.48
4.49
4.50
4.51
4.52
4.53
4.54
4.55
4.56
4.57
4.58
4.59
4.60
4.61
4.62
4.63
4.64
4.65
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Secondary Bus Number Register ........................................................................................
Subordinate Bus Number Register ......................................................................................
Secondary Latency Timer Register ......................................................................................
I/O Base Register ..........................................................................................................
I/O Limit Register ...........................................................................................................
Secondary Status Register................................................................................................
Memory Base Register ....................................................................................................
Memory Limit Register .....................................................................................................
Prefetchable Memory Base Register ....................................................................................
Prefetchable Memory Limit Register .....................................................................................
Prefetchable Base Upper 32 Bits Register..............................................................................
Prefetchable Limit Upper 32 Bits Register ..............................................................................
I/O Base Upper 16 Bits Register .........................................................................................
I/O Limit Upper 16 Bits Register..........................................................................................
Capabilities Pointer Register..............................................................................................
Interrupt Line Register .....................................................................................................
Interrupt Pin Register ......................................................................................................
Bridge Control Register....................................................................................................
PM Capability ID Register .................................................................................................
Next Item Pointer Register ................................................................................................
Power Management Capabilities Register ..............................................................................
Power Management Control/Status Register ...........................................................................
Power Management Bridge Support Extension Register .............................................................
Power Management Data Register ......................................................................................
MSI Capability ID Register ................................................................................................
Next Item Pointer Register ................................................................................................
MSI Message Control Register ...........................................................................................
MSI Message Lower Address Register .................................................................................
MSI Message Upper Address Register .................................................................................
MSI Message Data Register ..............................................................................................
SSID/SSVID Capability ID Register......................................................................................
Next Item Pointer Register ...............................................................................................
Subsystem Vendor ID Register...........................................................................................
Subsystem ID Register ....................................................................................................
PCI Express Capability ID Register ......................................................................................
Next Item Pointer Register ................................................................................................
PCI Express Capabilities Register .......................................................................................
Device Capabilities Register ..............................................................................................
Device Control Register ...................................................................................................
Device Status Register ....................................................................................................
Link Capabilities Register .................................................................................................
Link Control Register ......................................................................................................
Link Status Register........................................................................................................
Serial-Bus Data Register ..................................................................................................
Serial-Bus Word Address Register.......................................................................................
Serial-Bus Slave Address Register .....................................................................................
Serial-Bus Control and Status Register .................................................................................
GPIO Control Register .....................................................................................................
GPIO Data Register ........................................................................................................
Control and Diagnostic Register 0 .......................................................................................
Control and Diagnostic Register 1 .......................................................................................
PHY Control and Diagnostic Register 2 .................................................................................
Subsystem Access Register ..............................................................................................
Contents
55
56
56
56
57
58
59
59
60
60
61
61
62
62
63
63
63
64
66
66
67
68
69
69
69
70
70
71
71
72
72
72
73
73
73
73
74
75
76
77
78
79
80
80
80
81
82
83
84
85
87
88
89
3
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.66
4.67
4.68
4.69
4.70
4.71
4.72
4.73
4.74
4.75
5
Advanced Error Reporting Capability ID Register ..................................................................... 97
Next Capability Offset/Capability Version Register .................................................................... 98
Uncorrectable Error Status Register ..................................................................................... 98
Uncorrectable Error Mask Register ...................................................................................... 99
Uncorrectable Error Severity Register ................................................................................. 100
Correctable Error Status Register ...................................................................................... 101
Correctable Error Mask Register ....................................................................................... 102
Advanced Error Capabilities and Control Register ................................................................... 103
Header Log Register ..................................................................................................... 103
Secondary Uncorrectable Error Status Register ...................................................................... 104
Secondary Uncorrectable Error Mask Register ....................................................................... 105
Secondary Uncorrectable Error Severity .............................................................................. 106
Secondary Error Capabilities and Control Register .................................................................. 107
Secondary Header Log Register........................................................................................ 108
Device Control Map ID Register ........................................................................................
Revision ID Register......................................................................................................
GPIO Control Register ...................................................................................................
GPIO Data Register ......................................................................................................
Serial-Bus Data Register ................................................................................................
Serial-Bus Word Address Register .....................................................................................
Serial-Bus Slave Address Register ....................................................................................
Serial-Bus Control and Status Register ................................................................................
109
110
110
111
112
112
112
113
1394 OHCI PCI Configuration Space.................................................................................... 114
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
7.12
7.13
7.14
7.15
7.16
7.17
4
89
92
92
92
93
94
95
96
96
96
Memory-Mapped TI Proprietary Register Space .................................................................... 109
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
7
General Control Register ..................................................................................................
TI Proprietary Register ....................................................................................................
TI Proprietary Register ....................................................................................................
TI Proprietary Register.....................................................................................................
Arbiter Control Register ...................................................................................................
Arbiter Request Mask Register ...........................................................................................
Arbiter Time-Out Status Register ........................................................................................
TI Proprietary Register.....................................................................................................
TI Proprietary Register ....................................................................................................
TI Proprietary Register.....................................................................................................
PCIe Extended Configuration Space ..................................................................................... 97
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
5.10
5.11
5.12
5.13
5.14
6
www.ti.com
Vendor ID Register .......................................................................................................
Device ID Register ........................................................................................................
Command Register .......................................................................................................
Status Register ............................................................................................................
Class Code and Revision ID Registers ................................................................................
Cache Line Size and Latency Timer Registers .......................................................................
Header Type and BIST Registers ......................................................................................
OHCI Base Address Register ...........................................................................................
TI Extension Base Address Register ...................................................................................
CIS Base Address Register .............................................................................................
CIS Pointer Register......................................................................................................
Subsystem Vendor ID and Subsystem ID Registers .................................................................
Power Management Capabilities Pointer Register ...................................................................
Interrupt Line and Interrupt Pin Registers .............................................................................
Minimum Grant and Minimum Latency Registers ....................................................................
OHCI Control Register ...................................................................................................
Capability ID and Next Item Pointer Registers .......................................................................
Contents
115
115
116
117
118
118
119
119
120
120
121
121
122
122
123
123
124
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
7.18
7.19
7.20
7.21
7.22
7.23
8
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Power Management Capabilities Register ............................................................................
Power Management Control and Status Register ....................................................................
Power Management Extension Registers .............................................................................
PCI Miscellaneous Configuration Register ............................................................................
Link Enhancement Control Register ...................................................................................
Subsystem Access Register.............................................................................................
124
125
125
125
128
130
1394 OHCI Memory-Mapped Register Space ........................................................................ 131
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
8.10
8.11
8.12
8.13
8.14
8.15
8.16
8.17
8.18
8.19
8.20
8.21
8.22
8.23
8.24
8.25
8.26
8.27
8.28
8.29
8.30
8.31
8.32
8.33
8.34
8.35
8.36
8.37
8.38
8.39
8.40
8.41
8.42
8.43
8.44
8.45
8.46
OHCI Version Register ...................................................................................................
GUID ROM Register .....................................................................................................
Asynchronous Transmit Retries Register ..............................................................................
CSR Data Register ......................................................................................................
CSR Compare Register ..................................................................................................
CSR Control Register ....................................................................................................
Configuration ROM Header Register...................................................................................
Bus Identification Register ...............................................................................................
Bus Options Register .....................................................................................................
GUID High Register ......................................................................................................
GUID Low Register .......................................................................................................
Configuration ROM Mapping Register .................................................................................
Posted Write Address Low Register ...................................................................................
Posted Write Address High Register ...................................................................................
Vendor ID Register .......................................................................................................
Host Controller Control Register ........................................................................................
Self-ID Buffer Pointer Register ..........................................................................................
Self-ID Count Register ...................................................................................................
Isochronous Receive Channel Mask High Register ..................................................................
Isochronous Receive Channel Mask Low Register ..................................................................
Interrupt Event Register ..................................................................................................
Interrupt Mask Register ..................................................................................................
Isochronous Transmit Interrupt Event Register .......................................................................
Isochronous Transmit Interrupt Mask Register .......................................................................
Isochronous Receive Interrupt Event Register........................................................................
Isochronous Receive Interrupt Mask Register ........................................................................
Initial Bandwidth Available Register ....................................................................................
Initial Channels Available High Register ...............................................................................
Initial Channels Available Low Register ...............................................................................
Fairness Control Register................................................................................................
Link Control Register .....................................................................................................
Node Identification Register .............................................................................................
PHY Control Register ....................................................................................................
Isochronous Cycle Timer Register .....................................................................................
Asynchronous Request Filter High Register .........................................................................
Asynchronous Request Filter Low Register ...........................................................................
Physical Request Filter High Register .................................................................................
Physical Request Filter Low Register ..................................................................................
Physical Upper Bound Register (Optional Register) .................................................................
Asynchronous Context Control Register ...............................................................................
Asynchronous Context Command Pointer Register..................................................................
Isochronous Transmit Context Control Register ......................................................................
Isochronous Transmit Context Command Pointer Register .........................................................
Isochronous Receive Context Control Register.......................................................................
Isochronous Receive Context Command Pointer Register .........................................................
Isochronous Receive Context Match Register ........................................................................
Contents
134
135
136
136
137
137
138
138
139
140
140
141
141
142
142
142
144
144
145
146
146
148
150
151
151
152
152
153
153
154
155
156
157
158
158
161
161
164
164
165
166
167
168
168
170
170
5
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
9
1394 OHCI Memory-Mapped TI Extension Register Space...................................................... 172
9.1
9.2
9.3
9.4
9.5
10
Digital Video (DV) and MPEG2 Timestamp Enhancements ........................................................
Isochronous Receive Digital Video Enhancements ..................................................................
Isochronous Receive Digital Video Enhancement Registers .......................................................
Link Enhancement Control Registers ..................................................................................
Timestamp Offset Registers .............................................................................................
Physical Layer (PHY) Section
10.1
10.2
11
www.ti.com
172
173
173
174
176
............................................................................................ 177
PHY Section Register Configuration ...................................................................................
PHY Section Application Information...................................................................................
10.2.1 Power Class Programming ...................................................................................
10.2.2 Power-Up Reset ................................................................................................
10.2.3 Crystal Oscillator Selection ...................................................................................
10.2.4 Bus Reset .......................................................................................................
178
185
185
186
186
187
Electrical Characteristics ................................................................................................... 188
11.1
11.2
11.3
11.4
11.5
11.6
11.7
11.8
11.9
11.10
11.11
11.12
Absolute Maximum Ratings .............................................................................................
Recommended Operating Conditions ..................................................................................
PCIe Differential Transmitter Output Ranges .........................................................................
PCIe Differential Receiver Input Ranges ..............................................................................
PCIe Differential Reference Clock Input Ranges .....................................................................
Electrical Characteristics Over Recommended Operating Conditions (3.3-V I/O) ...............................
Electrical Characteristics Over Recommended Operating Conditions (PHY Port Driver) ......................
Switching Characteristics for PHY Port Driver .......................................................................
Electrical Characteristics Over Recommended Operating Conditions PHY Port Receiver ....................
Jitter/Skew Characteristics for 1394a PHY Port Receiver .........................................................
Operating, Timing, and Switching Characteristics of XI ............................................................
Electrical Characteristics Over Recommended Operating Conditions
(1394a Miscellaneous I/O) ..............................................................................................
188
188
189
191
192
192
193
193
194
194
194
194
12
Glossary .......................................................................................................................... 195
6
Contents
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
List of Figures
3-1
XIO2213B Block Diagram ........................................................................................................ 32
3-2
Power-Up Sequence .............................................................................................................. 33
3-3
Power-Down Sequence .......................................................................................................... 34
3-4
PCIe Assert_INTA Message ..................................................................................................... 38
3-5
PCIe Deassert_INTX Message.................................................................................................. 38
3-6
Serial EEPROM Application ..................................................................................................... 39
3-7
Serial-Bus Start/Stop Conditions and Bit Transfers .......................................................................... 40
3-8
Serial-Bus Protocol Acknowledge............................................................................................... 40
3-9
Serial-Bus Protocol Byte Write .................................................................................................. 41
3-10
Serial-Bus Protocol Byte Read .................................................................................................. 41
3-11
Serial-Bus Protocol Multibyte Read............................................................................................. 41
11-1
Test Load Diagram .............................................................................................................. 193
List of Figures
7
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
List of Tables
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
4-16
4-17
4-18
4-19
4-20
8
7 × 7 Terminals Sorted By Ball Number
.......................................................................................
7 × 7 Terminals Sorted Alphanumerically ......................................................................................
12 × 12 Terminals Sorted By Ball Number ....................................................................................
12 × 12 Terminals Sorted Alphanumerically ...................................................................................
Power-Supply Terminals .........................................................................................................
Ground Terminals .................................................................................................................
PCIe Terminals ....................................................................................................................
Clock Terminals ...................................................................................................................
1394 Terminals ....................................................................................................................
Reserved Terminals ..............................................................................................................
Miscellaneous Terminals .........................................................................................................
XIO2213B Reset Options ........................................................................................................
Initial Flow Control Credit Advertisements .....................................................................................
Messages Supported by Bridge .................................................................................................
EEPROM Register Loading Map................................................................................................
Registers Used To Program Serial-Bus Devices .............................................................................
Clocking In Low Power States...................................................................................................
1394b OHCI Configuration Register Map ......................................................................................
1394 OHCI Memory Command Options .......................................................................................
Classic PCI Configuration Register Map .......................................................................................
Command Register Description .................................................................................................
Status Register Description ......................................................................................................
Class Code and Revision ID Register Description ...........................................................................
Device Control Base Address Register Description ..........................................................................
Device Control Base Address Register Description ..........................................................................
I/O Base Register Description ...................................................................................................
I/O Limit Register Description ...................................................................................................
Secondary Status Register Description ........................................................................................
Memory Base Register Description .............................................................................................
Memory Limit Register Description .............................................................................................
Prefetchable Memory Base Register Description .............................................................................
Prefetchable Memory Limit Register Description .............................................................................
Prefetchable Base Upper 32 Bits Register Description ......................................................................
Prefetchable Limit Upper 32 Bits Register Description.......................................................................
I/O Base Upper 16 Bits Register Description..................................................................................
I/O Limit Upper 16 Bits Register Description ..................................................................................
Bridge Control Register Description ............................................................................................
Power Management Capabilities Register Description ......................................................................
Power Management Control/Status Register Description ...................................................................
List of Tables
17
19
21
23
26
27
27
27
28
30
30
35
36
37
42
44
45
47
48
49
51
52
53
54
55
56
57
58
59
59
60
60
61
61
62
62
64
67
68
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4-21
PM Bridge Support Extension Register Description .......................................................................... 69
4-22
................................................................................... 70
MSI Message Lower Address Register Description .......................................................................... 71
MSI Message Data Register Description ...................................................................................... 72
PCI Express Capabilities Register Description ................................................................................ 74
Device Capabilities Register Description ...................................................................................... 75
Device Control Register Description ............................................................................................ 76
Device Status Register Description ............................................................................................. 77
Link Capabilities Register Description .......................................................................................... 78
Link Control Register Description ............................................................................................... 79
Link Status Register Description ................................................................................................ 80
Serial-Bus Slave Address Register Descriptions ............................................................................. 81
Serial-Bus Control and Status Register Description .......................................................................... 82
GPIO Control Register Description ............................................................................................. 83
GPIO Data Register Description ................................................................................................ 84
Control and Diagnostic Register 0 Description ............................................................................... 85
Control and Diagnostic Register 1 Description ............................................................................... 87
Control and Diagnostic Register 2 Description ............................................................................... 88
Subsystem Access Register Description....................................................................................... 89
General Control Register Description .......................................................................................... 90
Arbiter Control Register Description ............................................................................................ 93
Arbiter Request Mask Register Description ................................................................................... 94
Arbiter Time-Out Status Register Description ................................................................................. 95
PCIe Extended Configuration Register Map ................................................................................... 97
Uncorrectable Error Status Register Description ............................................................................. 98
Uncorrectable Error Mask Register Description............................................................................... 99
Uncorrectable Error Severity Register Description .......................................................................... 100
Correctable Error Status Register Description ............................................................................... 101
Correctable Error Mask Register Description ................................................................................ 102
Advanced Error Capabilities and Control Register Description............................................................ 103
Secondary Uncorrectable Error Status Register Description .............................................................. 104
Secondary Uncorrectable Error Mask Register Description ............................................................... 105
Secondary Uncorrectable Error Severity Register Description ........................................................... 106
Secondary Error Capabilities and Control Register Description ........................................................... 107
Secondary Header Log Register Description ................................................................................ 108
Device Control Memory Window Register Map ............................................................................. 109
GPIO Control Register Description ............................................................................................ 110
GPIO Data Register Description ............................................................................................... 111
Serial-Bus Slave Address Register Descriptions ............................................................................ 112
Serial-Bus Control and Status Register Description ........................................................................ 113
1394 OHCI Configuration Register Map ...................................................................................... 114
4-23
4-24
4-25
4-26
4-27
4-28
4-29
4-30
4-31
4-32
4-33
4-34
4-35
4-36
4-37
4-38
4-39
4-40
4-41
4-42
4-43
5-1
5-2
5-3
5-4
5-5
5-6
5-7
5-8
5-9
5-10
5-11
5-12
6-1
6-2
6-3
6-4
6-5
7-1
MSI Message Control Register Description
List of Tables
9
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
7-2
Command Register Description................................................................................................ 116
7-3
Status Register Description .................................................................................................... 117
7-4
Class Code and Revision ID Registers Description ......................................................................... 118
7-5
Latency Timer and Class Cache Line Size Registers Description ........................................................ 118
7-6
Header Type and BIST Registers Description
7-7
7-8
7-9
7-10
7-11
7-12
7-13
7-14
7-15
7-16
7-17
7-18
7-19
8-1
8-2
8-3
8-4
8-5
8-6
8-7
8-8
8-9
8-10
8-11
8-12
8-13
8-14
8-15
8-16
8-17
8-18
8-19
8-20
8-21
8-22
8-23
10
..............................................................................
OHCI Base Address Register Description....................................................................................
TI Base Address Register Description ........................................................................................
Subsystem Vendor ID and Subsystem ID Registers Description .........................................................
Interrupt Line and Interrupt Pin Registers Description ......................................................................
Minimum Grant and Minimum Latency Registers Description .............................................................
OHCI Control Register Description ............................................................................................
Capability ID and Next Item Pointer Registers Description ................................................................
Power Management Capabilities Register Description .....................................................................
Power Management Control and Status Register Description ............................................................
Power Management Extension Registers Description ......................................................................
PCI Miscellaneous Configuration Register ...................................................................................
Link Enhancement Control Register Description ............................................................................
Subsystem Access Register Description .....................................................................................
OHCI Register Map .............................................................................................................
OHCI Version Register Description ...........................................................................................
GUID ROM Register Description ..............................................................................................
Asynchronous Transmit Retries Register Description ......................................................................
CSR Control Register Description .............................................................................................
Configuration ROM Header Register Description ...........................................................................
Bus Options Register Description .............................................................................................
Configuration ROM Mapping Register Description ..........................................................................
Posted Write Address Low Register Description ............................................................................
Posted Write Address High Register Description ...........................................................................
Host Controller Control Register Description ................................................................................
Self-ID Count Register Description ............................................................................................
Isochronous Receive Channel Mask High Register Description ..........................................................
Isochronous Receive Channel Mask Low Register Description ...........................................................
Interrupt Event Register Description ..........................................................................................
Interrupt Mask Register Description ...........................................................................................
Isochronous Transmit Interrupt Event Register Description ...............................................................
Isochronous Receive Interrupt Event Register Description ................................................................
Initial Bandwidth Available Register Description ............................................................................
Initial Channels Available High Register Description .......................................................................
Initial Channels Available Low Register Description ........................................................................
Fairness Control Registre Description ........................................................................................
Link Control Register Description .............................................................................................
List of Tables
119
119
120
121
122
123
123
124
124
125
125
127
129
130
131
134
135
136
137
138
139
141
141
142
143
144
145
146
147
148
150
151
152
153
153
154
155
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8-24
Node Identification Register Description...................................................................................... 156
8-25
PHY Control Register Description ............................................................................................. 157
8-26
Isochronous Cycle Timer Register Description .............................................................................. 158
8-27
Asynchronous Request Filter High Register Description ................................................................... 159
8-28
...................................................................
Physical Request Filter High Register Description ..........................................................................
Physical Request Filter Low Register Description ..........................................................................
Asynchronous Context Control Register Description .......................................................................
Asynchronous Context Command Pointer Register Description .........................................................
Isochronous Transmit Context Control Register Description ..............................................................
Isochronous Receive Context Control Register Description ...............................................................
Isochronous Receive Context Match Register Description ................................................................
TI Extension Register Map .....................................................................................................
Isochronous Receive Digital Video Enhancement Registers Description ................................................
Link Enhancement Control Registers Description ...........................................................................
Timestamp Offset Registers Description .....................................................................................
Base Register Description ......................................................................................................
Base Register Field Description ...............................................................................................
Page 0 (Port Status) Register Description ...................................................................................
Page 0 (Port Status) Register Field Description .............................................................................
Page 1 (Vendor ID) Register Configuration ..................................................................................
Page 1 (Vendor ID) Register Field Descriptions.............................................................................
Page 7 (Vendor Dependent) Register Configuration .......................................................................
Page 7 (Vendor Dependent) Register Field Descriptions ..................................................................
Power Class Register Description .............................................................................................
8-29
8-30
8-31
8-32
8-33
8-34
8-35
9-1
9-2
9-3
9-4
10-1
10-2
10-3
10-4
10-5
10-6
10-7
10-8
10-9
Asynchronous Request Filter Low Register Description
161
162
164
165
166
167
169
170
172
173
174
176
179
179
181
182
183
184
185
185
185
OHCI-Lynx is a trademark of Texas Instruments.
PCI Express is a trademark of PCI-SIG.
List of Tables
11
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
12
List of Tables
www.ti.com
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
1
Introduction
1.1
XIO2213B Features
•
•
•
•
•
•
Full ×1 PCI Express™ (PCIe) Throughput
Fully Compliant With PCI Express Base
Specification, Revision 1.1
Utilizes 100-MHz Differential PCI Express
Common Reference Clock or 125-MHz
Single-Ended Reference Clock
Fully Supports Provisions of IEEE Std
P1394b-2002
Fully Compliant With Provisions of IEEE Std
1394-1995 for a High-Performance Serial Bus
and IEEE Std 1394a-2000
Fully Compliant With 1394 Open Host
Controller Interface (OHCI) Specification,
Revision 1.1 and Revision 1.2 Draft
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
•
•
•
•
•
•
•
Three IEEE Std 1394b Fully Compliant Cable
Ports at 100M Bit/s, 200M Bit/s, 400M Bit/s, and
800M Bit/s
Cable Ports Monitor Line Conditions for Active
Connection to Remote Node
Cable Power Presence Monitoring
EEPROM Configuration Support to Load
Global Unique ID for 1394 Fabric
Support for D1, D2, D3hot
Active-State Link Power Management Saves
Power When Packet Activity on the PCI
Express Link Is Idle, Using Both L0s and L1
States
Eight 3.3-V Multifunction General-Purpose I/O
(GPIO) Terminals
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this document.
OHCI-Lynx is a trademark of Texas Instruments.
PCI Express is a trademark of PCI-SIG.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2009, Texas Instruments Incorporated
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
2
www.ti.com
Overview
The Texas Instruments XIO2213B is a single-function PCI Express™ (PCIe) to PCI local bus translation
bridge, where the PCI bus interface is internally connected to a 1394b open host controller/link-layer
controller with a 3-port 1394b physical layer (PHY). When the XIO2213B is properly configured, this
solution provides full PCIe and 1394b functionality and performance.
2.1
Description
The TI XIO2213B is a PCIe to PCI translation bridge, where the PCI bus interface is internally connected
to a 1394b open host controller/link-layer controller with a 3-port 1394b PHY. The PCIe to PCI translation
bridge is fully compatible with the PCI Express to PCI/PCI-X Bridge Specification, Revision 1.0. Also, the
bridge supports the standard PCI-to-PCI bridge programming model. The 1394b OHCI controller function
is fully compatible with IEEE Std 1394b and the latest 1394 Open Host Controller Interface (OHCI)
Specification.
The XIO2213B simultaneously supports up to four posted write transactions, four nonposted transactions,
and four completion transactions pending in each direction at any time. Each posted write data queue and
completion data queue can store up to 8K bytes of data. The nonposted data queues can store up to 128
bytes of data.
The PCIe interface supports a ×1 link operating at full 250 Mbit/s packet throughput in each direction
simultaneously. Also, the bridge supports the advanced error reporting capability including ECRC as
defined in the PCI Express Base Specification, Revision 1.1. Supplemental firmware or software is
required to fully utilize both of these features.
Robust pipeline architecture is implemented to minimize system latency. If parity errors are detected,
packet poisoning is supported for both upstream and downstream operations.
PCIe power management (PM) features include active-state link PM, PME mechanisms, and all
conventional PCI D states. If the active-state link PM is enabled, the link automatically saves power when
idle using the L0s and L1 states. PM active-state NAK, PM PME, and PME-to-ACK messages are
supported. The bridge is compliant with the latest PCI Bus Power Management Specification and provides
several low-power modes, which enable the host power system to further reduce power consumption
Eight general-purpose inputs and outputs (GPIOs), configured through accesses to the PCIe configuration
space, allow for further system control and customization.
Deep FIFOs are provided to buffer 1394 data and accommodate large host bus latencies. The device
provides physical write posting and a highly tuned physical data path for SBP-2 performance. The device
is capable of transferring data between the PCIe bus and the 1394 bus at 100M bit/s, 200M bit/s, 400M
bit/s, and 800M bit/s. The device provides three 1394 ports that have separate cable bias (TPBIAS).
As required by the 1394 Open Host Controller Interface (OHCI) Specification, internal control registers are
memory mapped and nonprefetchable. This configuration header is accessed through configuration cycles
specified by PCIe, and it provides plug-and-play (PnP) compatibility.
The PHY provides the digital and analog transceiver functions needed to implement a 3-port node in a
cable-based 1394 network. Each cable port incorporates two differential line transceivers. The
transceivers include circuitry to monitor the line conditions as needed for determining connection status,
for initialization and arbitration, and for packet reception and transmission. An optional external 2-wire
serial EEPROM interface is provided to load the global unique ID for the 1394 fabric.
14
Overview
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
The XIO2213B requires an external 98.304-MHz crystal oscillator to generate a reference clock. The
external clock drives an internal phase-locked loop (PLL), which generates the required reference signal.
This reference signal provides the clock signals that control transmission of the outbound encoded
information. The power-down (PD) function, when enabled by asserting the PD terminal high, stops
operation of the PLL. Data bits to be transmitted through the cable ports are latched internally, combined
serially, encoded, and transmitted at 98.304, 196.608, 393.216, 491.52, or 983.04 Mbit/s (referred to as
S100, S200, S400, S400B, or S800 speed, respectively) as the outbound information stream.
To ensure that the XIO2213B conforms to IEEE Std 1394b-2002, the BMODE terminal must be asserted.
The BMODE terminal does not select the cable-interface mode of operation. BMODE selects the internal
PHY-section/LLC-section interface mode of operation and affects the arbitration modes on the cable.
BMODE must be pulled high during normal operation.
Three package terminals are used as inputs to set the default value for three configuration status bits in
the self-ID packet. They can be pulled high through a 1-kΩ resistor or hardwired low as a function of the
equipment design. The PC0, PC1, and PC2 terminals indicate the default power class status for the node
(the need for power from the cable or the ability to supply power to the cable). The contender bit in the
PHY register set indicates that the node is a contender either for the isochronous resource manager (IRM)
or for the bus manager (BM). On the XIO2213B, this bit can only be set by a write to the PHY register set.
If a node is to be a contender for IRM or BM, the node software must set this bit in the PHY register set.
Submit Documentation Feedback
Overview
15
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
2.2
Related Documents
•
•
•
•
•
•
•
•
•
•
•
•
•
2.3
www.ti.com
PCI Express™ to PCI/PCI-X Bridge Specification, Revision 1.0
PCI Express™ Base Specification, Revision 1.1
PCI Express™ Card Electromechanical Specification, Revision 1.1
PCI Local Bus Specification, Revision 2.3 and Revision 3.0
PCI-to-PCI Bridge Architecture Specification, Revision 1.1
PCI Bus Power-Management Interface Specification, Revision 1.1 and Revision 1.2
1394 Open Host Controller Interface (OHCI) Specification, Release 1.2
High-Performance Serial Bus, IEEE Std 1394-1995
High-Performance Serial Bus, Amendment 1, IEEE Std 1394a-2000
High-Performance Serial Bus, Amendment 2, IEEE Std 1394b-2002
Express Card Standard, Release 1.0 and Release 1.1
PCI Express™ Jitter and BER white paper
PCI Mobile Design Guide, Revision 1.1
Documents Conventions
Throughout this data manual, several conventions are used to convey information. These conventions are:
• To identify a binary number or field, a lower-case b follows the numbers. For example, 000b is a 3-bit
binary field.
• To identify a hexadecimal number or field, a lower-case h follows the numbers. For example, 8AFh is a
12-bit hexadecimal field.
• All other numbers that appear in this document that do not have either a b or h following the number
are assumed to be decimal format.
• If the signal or terminal name has a bar above the name (for example, GRST), this indicates the logical
NOT function. When asserted, this signal is a logic low, 0, or 0b.
• Differential signal names end with P, N, +, or – designators. The P or + designators signify the positive
signal associated with the differential pair. The N or – designators signify the negative signal
associated with the differential pair.
• RSVD indicates that the referenced item is reserved.
• In Sections 4 through 6, the configuration space for the bridge is defined. For each register bit, the
software access method is identified in an access column. The legend for this access column includes
the following entries:
– R: Read access by software
– U: Updates by the bridge internal hardware
– W: Write access by software
– C: Clear an asserted bit with a write back of 1b by software. Write of zero to the field has no effect.
– S: The field may be set by a write of one. Write of zero to the field has no effect.
– NA: Not accessible or not applicable
• The XIO2213B consists of a PCIe to PCI translation bridge, where the secondary PCI bus is internally
connected to a 1394b OHCI with a 3-port PHY. When describing functionality that is specific to the
PCIe to PCI translation bridge, the term bridge is used to reduce text. The term 1394b OHCI is used to
reduce text when describing the 1394b OHCI with 3-port PHY function.
• LLC refers to the 1394 link layer controller.
2.4
Ordering Information
VOLTAGE
ORDERABLE PART NUMBER
167-terminal (Lead-Free) PBGA – ZAY
PACKAGE
3.3-V and 1.5-V power terminals
XIO2213BZAY
168-terminal (Lead-Free) BGA – ZAJ
3.3-V and 1.5-V power terminals
XIO2213BZAJ
16
Overview
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
2.5
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Terminal Assignments
The XIO2213B is packaged in a 168-ball BGA (ZAJ) and a 167-ball PBGA (ZAY). For the ZAJ package
Table 2-1 lists the terminals sorted by ball number. Table 2-2 lists the terminals in alphanumerical order.
For the ZAY packageTable 2-3 lists the terminals sorted by ball number. Table 2-4 lists the terminals in
alphanumerical order.
BALL NO.
Table 2-1. 7 × 7 Terminals Sorted By Ball Number
BALL NO.
A01
A02
A03
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
B01
B03
B04
TERMINAL NAME
VDDA_33
CNA
TESTM
RXN
RXP
PHY_RESET
TXN
TXP
PCI
REF1_PCIE
REF0_PCIE
TPBIAS2
TPA2+
REFCLK+
PD
VDDA_15
B05
VDDA_15
B06
BMODE
B07
B08
B09
B10
B11
B12
B13
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
VREG_PD
PC2
VDD_33_COMB
VDD_33_COM_IO
VDD_15_COMB
PERST
TPA2–
REFCLK–
LINKON_L
LPS_L
VDDA_15
VDDA_15
VSSA_PCIE
VDD_15
VDDA_33
VDD_33_AUX
RSVD
PC0
C12
GRST
C13
TPB2+
D01
D02
D03
D04
D05
D06
D07
Submit Documentation Feedback
LREQ_L
LKON/DS2_P
LPS_P
VSSA
VSSA_PCIE
VSSA_PCIE
VSSA
TERMINAL NAME
D08
DVDD_CORE
D09
DVDD_CORE
D10
VDD_33
D11
RSVD
D12
RSVD
D13
TPB2–
E01
LREQ_P
E02
PINT_L
E03
PINT_P
E04
DVDD_3.3
E05
GND
E06
VSSA_PCIE
E07
VSS
E08
VSS
E09
VSSA
E10
AVDD_3.3
E11
RSVD
E12
TPBIAS1
E13
TPA1+
F01
CTL0
F02
PCLK_P
F03
PCLK_L
F04
GND
F05
GND
F06
GND
F07
GND
F08
GND
F09
GND
F10
AVDD_3.3
F11
RSVD
F12
RSVD
F13
TPA1–
G01
CTL1
G02
LCLK_P
G03
LCLK_L
G04
GND
G05
GND
G06
GND
G07
GND
G08
GND
G09
GND
G10
GND
G11
REFCLK_SEL
G12
SCL
G13
TPB1_
H01
D0
H02
D1
Overview
17
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-1. 7 × 7 Terminals Sorted By Ball Number
(continued)
BALL NO.
H03
VDD_15
H04
GND
H05
GND
H06
GND
H07
H08
H09
H10
H11
H12
H13
J01
J02
J03
J05
J06
J07
J08
J09
J10
J11
GND
GND
VDD_15
AVDD_3.3
SDA
CLKREQ
TPB1–
D3
D2
VDD_15
GND
GND
GND
GND
VDD_15
AVDD_3.3
RSVD
J12
TPBIAS0
J13
TPA0+
K01
D5
K02
K03
K04
K05
K06
K07
K08
K09
K10
K11
K12
K13
18
TERMINAL NAME
Overview
D4
VDD_33
GPIO5
DVDD_3.3
DVDD_3.3
GND
VDD_33
DVDD_CORE
RSVD
RSVD
RSVD
TPA0–
www.ti.com
BALL NO.
TERMINAL NAME
L01
D6
L02
GPIO2
L03
VDD_33
L04
GPIO3
L05
GPIO7
L06
VDD_15
L07
GND
L08
VDD_33
L09
CYCLEOUT
L10
RSVD
L11
RSVD
L12
RSVD
L13
TPB0+
M01
D7
M02
GPIO0
M03
GPIO4
M04
AVDD_3.3
M05
XO
M06
GPIO6
M07
DS1
M08
OHCI_PME
M09
RSVD
M10
SE
M11
RSVD
M12
RSVD
M13
TPB0–
N01
GPIO1
N02
R1
N03
R0
N04
PLLGND
N05
XI
N06
PLLVDD_CORE
N07
PLLVDD_3.3
N08
DS0
N09
CPS
N10
SM
N11
RSVD
N12
RSVD
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-2. 7 × 7 Terminals Sorted
Alphanumerically
BALL NO.
E10
TERMINAL NAME
AVDD_3.3
F10
AVDD_3.3
H10
AVDD_3.3
J10
M04
B06
H12
A02
N09
F01
G01
L09
H01
H02
J02
J01
K02
K01
L01
M01
N08
AVDD_3.3
AVDD_3.3
BMODE
CLKREQ
CNA
CPS
CTL0
CTL1
CYCLEOUT
D0
D1
D2
D3
D4
D5
D6
D7
DS0
M07
DS1
E04
DVDD_3.3
K05
K06
D08
D09
K09
E05
F04
F05
F06
F07
F08
F09
G04
G05
G06
G07
G08
G09
DVDD_3.3
DVDD_3.3
DVDD_CORE
DVDD_CORE
DVDD_CORE
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
G10
GND
H04
GND
H05
H06
H07
H08
J04
J05
J06
Submit Documentation Feedback
GND
GND
GND
GND
GND
GND
GND
BALL NO.
TERMINAL NAME
J07
GND
J08
GND
K07
GND
L07
GND
M02
GPIO0
N01
GPIO1
L02
GPIO2
L04
GPIO3
M03
GPIO4
K04
GPIO5
M06
GPIO6
L05
GPIO7
C12
GRST
G03
LCLK_L
G02
LCLK_P
C02
LINKON_L
D02
LKON/DS2_P
C03
LPS_L
D03
LP2_P
D01
LREQ_L
E01
LREQ_P
M08
OHCI_PME
C11
PC0
A09
PC1
B08
PC2
F03
PCLK_L
F02
PCLK_P
B03
PD
B12
PERST
E02
PINT_L
E03
PINT_P
N04
PLLGND
N07
PLLVDD_3.3
N06
PLLVDD_CORE
N03
R0
N02
R1
A11
REF0_PCIE
A10
REF1_PCIE
C01
REFCLK–
G11
REFCLK_SEL
B01
REFCLK+
A06
PHY_RESET
C10
RSVD
D11
RSVD
D12
RSVD
E11
RSVD
F11
RSVD
F12
RSVD
J11
RSVD
K10
RSVD
K11
RSVD
K12
RSVD
Overview
19
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-2. 7 × 7 Terminals Sorted
Alphanumerically (continued)
BALL NO.
L10
RSVD
L11
RSVD
L12
RSVD
M09
RSVD
M11
M12
N11
N12
N13
A04
A05
G12
H11
M10
N10
A03
B07
K13
J13
F13
E13
RSVD
RSVD
RSVD
RSVD
RSVD
RXN
RXP
SCL
SDA
SE
SM
TESTM
VREG_PD
TPA0–
TPA0+
TPA1–
TPA1+
B13
TPA2–
A13
TPA2+
M13
TPB0–
L13
H13
G13
D13
C13
J12
E12
A12
20
TERMINAL NAME
Overview
TPB0+
TPB1–
TPB1+
TPB2–
TPB2+
TPBIAS0
TPBIAS1
TPBIAS2
www.ti.com
BALL NO.
TERMINAL NAME
A07
TXN
A08
TXP
C07
VDD_15
H03
VDD_15
H09
VDD_15
J03
VDD_15
J09
VDD_15
L06
VDD_15
B11
VDD_15_COMB
C09
VDD_33_AUX
D10
VDD_33
K03
VDD_33
K08
VDD_33
L03
VDD_33
L08
VDD_33
B10
VDD_33_COM_IO
B09
VDD_33_COMB
B04
VDDA_15
B05
VDDA_15
C04
VDDA_15
C05
VDDA_15
A01
VDDA_33
C08
VDDA_33
E07
VSS
E08
VSS
D04
VSSA
D07
VSSA
E09
VSSA
C06
VSSA_PCIE
D05
VSSA_PCIE
D06
VSSA_PCIE
E06
VSSA_PCIE
N05
XI
M05
XO
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-3. 12 × 12 Terminals Sorted By Ball
Number
BALL NO.
A01
TERMINAL NAME
REFCLK+
A02
CNA
A03
RXN
A04
A05
A06
A07
A08
A09
A10
A11
A12
A13
A14
B01
B02
B03
B04
B05
B06
B07
RXP
BMODE
VREG_PD
VSS
TXN
TXP
VDDA_33
PC2
REF1_PCIE
REF0_PCIE
VSS
REFCLK–
TESTM
PD
PHY_RESET
VDDA_15
VSSA
VDDA_15
B08
VDD_15
B09
VDDA_15
B10
B11
B12
B13
B14
C01
C02
C03
C04
C05
C06
C07
C08
C09
C10
C11
C12
C13
VDDA_15
VDD_33_COMB
VDD_33
PERST
TPA2+
LPS_L
LPS_P
VDDA_33
VSSA_PCIE
VSSA_PCIE
VSSA_PCIE
VSSA_PCIE
DVDD_3.3
DVDD_CORE
VSSA
VDD_33_COM_IO
VDD_15_COMB
GRST
C14
TPA2–
D01
LKON/DS2_P
D02
D03
D12
D13
D14
E01
E02
Submit Documentation Feedback
PINT_L
PINT_P
RSVD
RSVD
TPB2+
LINKON_L
LREQ_P
BALL NO.
TERMINAL NAME
E03
VDD_33
E06
GND
E07
GND
E08
PC1
E09
PC0
E10
AVDD_3.3
E12
RSVD
E13
TPBIAS2
E14
TPB2–
F01
PCLK_P
F02
LREQ_L
F03
DVDD_CORE
F05
VSSA
F06
GND
F07
GND
F08
GND
F09
GND
F10
AVDD_3.3
F12
RSVD
F13
RSVD
F14
TPA1+
G01
PCLK_L
G02
LCLK_L
G03
VDD_15
G05
GND
G06
GND
G07
GND
G08
GND
G09
GND
G10
VDD_33
G12
RSVD
G13
TPBIAS1
G14
TPA1–
H01
CTL0
H02
LCLK_P
H03
VDD_15
H05
GND
H06
GND
H07
GND
H08
GND
H09
GND
H10
VDD_33
H12
SDA
H13
REFCLK_SEL
H14
TPB1+
J01
CTL1
J02
D0
J03
DVDD_3.3
J05
GND
J06
GND
J07
GND
J08
GND
Overview
21
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-3. 12 × 12 Terminals Sorted By Ball
Number (continued)
BALL NO.
J09
AVDD_3.3
J10
VDD_33
J12
CLKREQ
J13
SCL
J14
K01
K02
K03
K05
K06
K07
K08
K09
K10
K12
K13
K14
L01
L02
L03
L12
TPB1–
D2
D1
DVDD_3.3
GND
GND
GND
GND
AVDD_3.3
VDD_15
RSVD
TPBIAS0
TPA0+
D3
D4
D5
RSVD
L13
RSVD
L14
TPA0–
M01
R1
M02
M03
M04
M05
M06
M07
M08
22
TERMINAL NAME
Overview
D6
D7
AVDD_3.3
VDD_33
VDD_15
PLLVDD_CORE
RSVD
www.ti.com
BALL NO.
TERMINAL NAME
M09
DVDD_CORE
M10
AVDD_3.3
M11
RSVD
M12
RSVD
M13
RSVD
M14
TPB0+
N01
R0
N02
GPIO1
N03
GPIO3
N04
GPIO4
N05
PLLGND
N06
GPIO7
N07
PLLVDD_3.3
N08
CYCLEOUT
N09
DS0
N10
RSVD
N11
RSVD
N12
RSVD
N13
RSVD
N14
TPB0–
P01
GPIO0
P02
GPIO2
P03
RSVD
P04
XI
P05
GPIO5
P06
GPIO6
P07
VDD_15
P08
OHCI_PME
P09
DS1
P10
RSVD
P11
RSVD
P12
CPS
P13
SE
P14
SM
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-4. 12 × 12 Terminals Sorted
Alphanumerically
TERMINAL NAME
BALL NO.
GND
J06
BALL NO.
GND
J07
AVDD_3.3
E10
GND
J08
AVDD_3.3
F10
GND
K05
J09
GND
K06
AVDD_3.3
K09
GND
K07
AVDD_3.3
M10
GND
K08
M04
GPIO0
P01
BMODE
A05
GPIO1
N02
CLKREQ
J12
GPIO2
P02
CNA
A02
GPIO3
N03
CPS
P12
GPIO3
N04
CTL0
H01
GPIO5
P05
CTL1
J01
GPIO6
P06
CYCLEOUT
N08
GPIO7
N06
D0
J02
GRST
C13
D1
K02
LCLK_L
G02
K01
LCLK_P
H02
D3
L01
LINKON_L
E01
D4
L02
LKON/DS2_P
D01
L03
LPS_L
C01
M02
LPS_P
C02
D7
M03
LREQ_L
F02
DS0
N09
LREQ_P
E02
P09
OHCI_PME
P08
DVDD_3.3
C08
PC0
E09
DVDD_3.3
J03
PC1
E08
K03
PC2
A11
DVDD_CORE
C09
PCLK_L
G01
DVDD_CORE
F03
PCLK_P
F01
DVDD_CORE
M09
PD
B03
GND
E06
PERST
B13
GND
E07
PINT_L
D02
GND
F06
PINT_P
D03
F07
PLLGND
N05
GND
F08
PLLVDD_3.3
N07
GND
F09
PLLVDD_CORE
M07
G05
R0
N01
GND
G06
R1
M01
GND
G07
REF0_PCIE
A13
G08
REF1_PCIE
A12
G09
REFCLK-
B01
GND
H05
REFCLK_SEL
H13
GND
H06
REFCLK+
A01
H07
PHY_RESET
B04
GND
H08
RSVD
G12
GND
H09
RSVD
F13
J05
RSVD
F12
TERMINAL NAME
AVDD_3.3
AVDD_3.3
D2
D5
D6
DS1
DVDD_3.3
GND
GND
GND
GND
GND
GND
Submit Documentation Feedback
Overview
23
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 2-4. 12 × 12 Terminals Sorted
Alphanumerically (continued)
TERMINAL NAME
TPB2+
BALL NO.
D14
BALL NO.
TPBIAS0
K13
RSVD
E12
TPBIAS1
G13
RSVD
D12
TPBIAS2
E13
RSVD
D13
TXN
A08
RSVD
M08
TXP
A09
RSVD
N10
VDD_15
G03
RSVD
P10
VDD_15
H03
P11
VDD_15
K10
RSVD
N11
VDD_15
M06
RSVD
M11
VDD_15
B08
RSVD
N12
VDD_15_COMB
C12
RSVD
N13
VDD_33
E03
RSVD
M12
VDD_33
G10
RSVD
M13
VDD_33
H10
RSVD
L13
VDD_33
J10
RSVD
K12
VDD_33
M05
RSVD
L12
VDD_33
B12
RXN
A03
VDD_33_COM_IO
C11
RXP
A04
VDD_33_COMB
B11
SCL
J13
VDDA_15
B10
H12
VDDA_15
B09
SE
P13
VDDA_15
B07
SM
P14
VDDA_15
B05
TESTM
B02
VDDA_33
C03
VREG_PD
A06
VDDA_33
A10
TPA0–
L14
VDD_15
P07
TPA0+
K14
VSS
A14
G14
VSS
A07
TPA1+
F14
VSSA
F05
TPA2–
C14
VSSA
C10
TPA2+
B14
VSSA
B06
TPB0–
N14
VSSA_PCIE
C04
TPB0+
M14
VSSA_PCIE
C05
TPB1–
J14
VSSA_PCIE
C06
TPB1+
H14
VSSA_PCIE
C07
TPB2–
E14
XI
P04
RSVD
P03
TERMINAL NAME
RSVD
SDA
TPA1–
24
Overview
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
2.6
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Terminal Descriptions
The following tables give a description of the terminals. These terminals are grouped in tables by
functionality. Each table includes the terminal name, terminal number, I/O type, and terminal description.
The following list describes the different input/output cell types that appear in the terminal description
tables:
• HS DIFF IN = High-speed differential input
• HS DIFF OUT = High-speed differential output
• LV CMOS = 3.3-V low-voltage CMOS input or output with 3.3-V clamp rail
• BIAS = Input/output terminals that generate a bias voltage to determine a driver's operating current
• Feedthrough = Terminals that connect directly to macros within the part and not through an input or
output cell
• PWR = Power terminal
• GND = Ground terminal
Submit Documentation Feedback
Overview
25
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 2-5. Power-Supply Terminals
BALL NO.
I/O
TYPE
EXTERNAL
PARTS
C07 H03
H09 J03
J09 L06
PWR
Bypass
capacitors
B10 B09
B07 B05
B04 B05
C04 C05
PWR
Filter
E03 M05
J10 H10
G10
D10 K03
K08 L03
L08
PWR
Bypass
capacitors
B12
C09
VDDA_33
C03 A10
A01 C08
PWR
Filter
DVDD_CORE
C09 F03
M09
D08 D09
K09
PWR
Bypass
capacitors
Digital 1.95-V circuit power for the PHY. A combination of
high-frequency decoupling capacitors near each terminal is
suggested, such as paralleled 0.1 µF and 0.001 µF. An
additional 1-µF capacitor is required for voltage regulation.
These supply terminals are separated from the other power
terminals internal to the device to provide noise isolation.
M07
N06
PWR
Bypass
capacitors
PLL 1.95-V circuit power for the PHY. A combination of
high-frequency decoupling capacitors near each terminal is
suggested, such as paralleled 0.1 µF and 0.001 µF. An
additional 1-µF capacitor is required for voltage regulation, and
the PLLVDD_CORE terminals must be separate from the
DVDD_CORE terminals. These supply terminals are separated
from the other power terminals internal to the device to provide
noise isolation.
DVDD_33
C08 J03
K03
E04 K05
K06
PWR
Bypass
capacitors
3.3-V digital I/O power for the PHY
AVDD_33
M04 E10
F10 J09
K09 M10
E10 F10
H10 J10
M04
PWR
Filter
PLLVDD_33
N07
N07
PWR
Bypass
capacitors
PLL 3.3-V circuit power for the PHY. This supply terminal is
separated from the other power terminals internal to the device
to provide noise isolation. The PLLVDD_33 and VDDA_33 pins
should be connected together with a low-dc-impedance
connection on the circuit board.
VDD_15_COMB
C12
B11
PWR
Bypass
capacitors
Internal 1.5-V main power output for external bypass capacitor
filtering
Caution: Do not use this terminal to supply external power to
other devices.
VDD_33_COMB
B11
B09
PWR
Bypass
capacitors
Internal 3.3-V main power output for external bypass capacitor
filtering
Caution: Do not use this terminal to supply external power to
other devices.
VDD_33_COMBIO
C11
B10
PWR
Bypass
capacitors
Internal 3.3-V IO power output for external bypass capacitor
filtering
Caution: Do not use this terminal to supply external power to
other devices.
SIGNAL
ZAY
PACKAGE
ZAJ
PACKAGE
VDD_15
G03 H03
K10 M06
B08 P07
VDDA_15
VDD_33
VDD_33_AUX
PLLVDD_CORE
26
Overview
DESCRIPTION
1.5-V digital core power for the link
1.5-V analog power for the link
3.3-V digital I/O power for the link
This terminal is connected to VSS through a pulldown resistor,
since the XIO2213B does not support auxiliary power.
3.3-V analog power for the link. This supply terminal is
separated from the other power terminals internal to the device
to provide noise isolation.
3.3-V analog power for the PHY
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-6. Ground Terminals
BALL NO.
SIGNAL
ZAY
PACKAGE
ZAJ
PACKAGE
I/O
TYPE
DESCRIPTION
VSS
A07 A14
E07 E08
GND
Digital ground for link
VSSA
B06 C10 F05
D04 D07 E09
GND
Analog ground for link
VSSA_PCIE
C04 C05 C06 C07
C06 D05 D06 E06
GND
Analog ground for PCIe function
PLLGND
N05
N04
GND
PLL circuit ground. This terminal must be tied to the
low-impedance circuit-board ground plane.
GND
Ground. These terminals must be tied together to the
low-impedance circuit-board ground plane.
GND
E06 E07 F06 F07 F08
E05 F04 F05 F06 F07
F09 G05 G06 G07 G08 F08 F09 G04 G05 G06
G09 H05 H06 H07 H08 G07 G08 G09 G10 H04
H09 J05 J06 J07 J08
H05 H06 H07 H08 J04
K05 K06 K07 K08
J05 J06 J07 J08 K07
L07
Table 2-7. PCIe Terminals
BALL NO.
SIGNAL
I/O
TYPE
ZAY
PACKAGE
ZAJ
PACKAGE
PERST
B13
B12
I
REF0_PCIE
REF1_PCIE
A13
A12
A11
A10
I/O
RXP
RXN
A04
A03
A05
A04
DI
TXP
TXN
A09
A08
A08
A07
DO
EXTERNAL
PARTS
DESCRIPTION
PCI Express reset. PERST identifies when the system power is stable
and generates an internal power-on reset.
Note: The PERST input buffer has hysteresis.
External
resistor
External reference resistor + and terminals for setting TX driver current.
An external resistor is connected between terminals REF0_PCIE and
REF1_PCIE.
High-speed receive pair. RXP and RXN comprise the differential
receive pair for the single PCIe lane supported.
Series
capacitors
High-speed transmit pair. TXP and TXN comprise the differential
transmit pair for the single PCIe lane supported.
Table 2-8. Clock Terminals
BALL NO.
SIGNAL
ZAY
PACKAGE
ZAJ
PACKAGE
REFCLK_SEL
H13
G11
I/O
TYPE
EXTERNAL
PARTS
I
Pullup or
pulldown
resistor
DESCRIPTION
Reference clock select. This terminal selects the reference clock input.
0 = 100-MHz differential common reference clock used
1 = 125-MHz single-ended reference clock used
REFCLK+
A01
B01
DI
REFCLK–
B01
C01
DI
CLKREQ
J12
H12
O
Clock request. This terminal is used to support the clock request
protocol.
XI
P04
N05
I
Oscillator input. This terminal connects to a 98.304-MHz low-jitter
external oscillator. XI is a 1.8-V CMOS input. Oscillator jitter must be
5-ps RMS or better. If only 3.3-V oscillators can be acquired, great care
must be taken to not introduce significant jitter by the means used to
level shift from 3.3 V to 1.8 V. If a resistor divider is used, a high-current
oscillator and low-value resistors must be used to minimize RC time
constants.
Submit Documentation Feedback
Reference clock positive. REFCLK+ and REFCLK– comprise the
differential input pair for the 100-MHz system reference clock. For a
single-ended, 125-MHz system reference clock, use the REFCLK+
input.
Capacitor to Reference clock negative. REFCLK+ and REFCLK– comprise the
VSS for
differential input pair for the 100-MHz system reference clock. For a
singlesingle-ended, 125-MHz system reference clock, attach a capacitor from
ended
REFCLK– to VSS.
mode
Overview
27
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 2-9. 1394 Terminals
BALL NO.
SIGNAL
I/O
TYPE
DESCRIPTION
ZAY
PACKAGE
ZAJ
PACKAGE
CNA
A02
A02
I/O
CPS
P12
N09
I
Cable power status. This terminal is normally connected to cable power through a
400-kΩ resistor. This circuit drives an internal comparator that detects the presence
of cable power. If CPS is not used to detect cable power, this terminal must be
connected to VSSA.
DS0
N09
N08
I
Data-strobe-only mode for port 0. IEEE Std 1394a-2000-only port-0-enable
programming terminal. On hardware reset, this terminal allows the user to select
whether port 0 acts like an IEEE Std 1394b-2002 bilingual port (terminal at logic 0) or
as an IEEE Std 1394a-2000-only port (terminal at logic 1). Programming is
accomplished by tying the terminal low through a 1-kΩ or smaller resistor (to enable
IEEE Std 1394b-2002 bilingual mode) or high through a 10-kΩ or smaller resistor (to
enable IEEE Std 1394a-2000-only mode).
DS1
P09
M07
I
Data-strobe-only mode for port 1. IEEE Std 1394a-2000-only port-1-enable
programming terminal. On hardware reset, this terminal allows the user to select
whether port 1 acts like an IEEE Std 1394b-2002 bilingual port (terminal at logic 0) or
as an IEEE Std 1394a-2000-only port (terminal at logic 1). Programming is
accomplished by tying the terminal low through a 1-kΩ or smaller resistor (to enable
IEEE Std 1394b-2002 bilingual mode) or high through a 10-kΩ or smaller resistor (to
enable IEEE Std 1394a-2000-only mode).
PC0
PC1
PC2
E09
E08
A11
C11
A09
B08
I
Power-class programming. On hardware reset, these inputs set the default value of
the power class indicated during self-ID. Programming is done by tying the terminals
high through a 1-kΩ or smaller resistor or by tying directly to ground through a 1-kΩ
or smaller resistor. Bus holders are built into these terminals.
R0
R1
N01
M01
N03
N02
I/O
Current-setting resistor. These terminals are connected to an external resistance to
set the internal operating currents and cable driver output currents. A resistance of
6.34 kΩ ± 1% is required to meet the IEEE Std 1394-1995 output voltage limits.
TPA0P
TPA0N
TPB0P
TPB0N
K14
L14
M14
N14
J13
K13
L13
M13
I/O
Port 0 twisted-pair cable A differential. Board trace lengths from each pair of positive
and negative differential signal pins must be matched and as short as possible to the
external load resistors and to the cable connector. For an unused port, TPA+ and
TPA– can be left open.
TPA1P
TPA1N
TPB1P
TPB1N
F14
G14
H14
J14
E13
F13
G13
H13
I/O
Port 1 twisted-pair cable A differential. Board trace lengths from each pair of positive
and negative differential signal pins must be matched and as short as possible to the
external load resistors and to the cable connector. For an unused port, TPA+ and
TPA– can be left open.
TPA2P
TPA2N
TPB2P
TPB2N
B14
C14
D14
E14
A13
B13
C13
D13
I/O
Port 2 twisted-pair cable A differential. Board trace lengths from each pair of positive
and negative differential signal pins must be matched and as short as possible to the
external load resistors and to the cable connector. For an unused port, TPA+ and
TPA– can be left open.
TPBIAS0
TPBIAS1
TPBIAS2
K13
G13
E13
J12
E12
A12
O
Twisted-pair bias. These terminals provide the 1.86-V nominal bias voltage needed
for proper operation of the twisted-pair cable drivers and receivers, and for signaling
to the remote nodes that there is an active cable connection in IEEE Std 1394a-2000
mode. Each of these terminals, except for an unused port, must be decoupled with a
1-µF capacitor to ground. For the unused port, this terminal can be left unconnected.
PCLK_L
G01
F03
I
PHY-section clock. This terminal must be connected to the PCLK_P output of the
PHY section.
PCLK_P
F01
F02
O
PHY-section clock. This terminal must be connected to the PCLK_L input of the LLC
section.
LCLK_L
G02
G03
O
LLC-section clock. This terminal must be connected to the LCLK_P input terminal of
the PHY section.
LCLK_P
H02
G02
I
LLC-section clock. This terminal must be connected to the LCLK_L output terminal of
the LLC section.
LPS_L
C01
C03
O
LLC-section power status. This terminal must be connected to the LPS_P input
terminal of the PHY section.
LPS_P
C02
D03
I
Link power status. This terminal must be connected to the LPS_L ouput terminal of
the LLC section.
28
Overview
Cable not active. This terminal is asserted high when there are no ports receiving
incoming bias voltage. If it is not used, this terminal should be left unconnected.
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-9. 1394 Terminals (continued)
BALL NO.
SIGNAL
I/O
TYPE
DESCRIPTION
ZAY
PACKAGE
ZAJ
PACKAGE
PINT_L
D02
E02
I
PHY-section interrupt. The PHY section uses this signal to transfer status and
interrupt information serially to the LLC section. This terminal must be connected to
the PINT_P output of the PHY section.
PINT_P
D03
E03
O
PHY-section interrupt. PINT_P is a serial input to the LLC section from the PHY
section that is used to transfer status, register, interrupt, and other information to the
link. Information encoded on PINT_P is synchronous to PCLK_P. This terminal must
be connected to the PINT_L input of the LLC section.
LKON/DS2_P
D01
D02
I/O
Link-on notification. If port is to operate in DS mode or is unused then it is necessary
to pull the terminal high through a 470-Ω or smaller resistor. This terminal must also
be connected to the LINKON_L input terminal of the LLC section via a 1-kΩ series
resistor. A bus holder is built into this terminal. If the port is to operate in bilingual
mode then the terminal should be tied low via a 1-kΩ resistor and directly connected
to the link's LINKON_L pin with no series termination. After hardware reset, this
terminal is the link-on output, which notifies the LLC section or other power-up logic
to power up and become active. The link-on output is a square-wave signal with a
period of approximately 163 ns (eight PCLK cycles) when active. The link-on output
is otherwise driven low, except during hardware reset when it is high impedance. The
link-on output is activated if the LLC section is inactive (the LPS input inactive or the
LCtrl bit cleared) and when any of the following occurs:
a) The XIO2213B receives a link-on PHY packet addressed to this node.
b) The PEI (port-event interrupt) register bit is 1.
c) Any of the configuration-timeout interrupt (CTOI), cable-power-status interrupt
(CPSI), or state-time-out interrupt (STOI) register bits are 1, and the resuming-port
interrupt enable (RPIE) register bit also is 1.
d) The PHY is power cycled and the power class is 0 through 4.
Once activated, the link-on output is active until the LLC section becomes active
(both the LPS_L input active and the LCtrl bit set). The PHY section also deasserts
the link-on output when a bus reset occurs unless the link-on output is otherwise
active because one of the interrupt bits is set (that is, the link-on output is active due
solely to the reception of a link-on PHY packet). In the case of power cycling, the
LKON signal must stop after 167 ms if the previous conditions have not been met.
Note: If an interrupt condition exists that otherwise causes the link-on output to be
activated if the LLC section were inactive, the link-on output is activated when the
LLC section subsequently becomes inactive.
LINKON_L
E01
C02
I/O
Link-on notification. LINKON_L is an input to the LLC section from the PHY section
that is used to provide notification that a link-on packet has been received or an
event, such as a port connection, has occurred. This I/O only has meaning when
LPS is disabled. This includes the D0 (uninitialized), D2, and D3 power states. If
LINKON_L becomes active in the D0 (uninitialized), D2, or D3 power state, the
XIO2213B device sets bit 15 (PME_STS) in the power-management control and
status register in the PCI configuration space at offset 48h. This terminal must be
connected to the LKON output terminal of the PHY section.
LREQ_L
F02
D01
O
LLC-section request. The LLC section uses this output to initiate a service request to
the PHY section.This terminal must be connected to the LREQ_P input of the PHY
section.
LREQ_P
E02
E01
I
LLC-section request. LREQ_P is a serial input from the LLC section to the PHY
section used to request packet transmissions, read and write PHY section registers,
and to indicate the occurrence of certain link events that are relevant to the PHY
section. Information encoded on LREQ_P is synchronous to LCLK_P.This terminal
must be connected to the LREQ_L output of the LLC section.
PHY_RESET
B04
A06
I
Reset for the 1394 PHY logic
CTL1
CTL0
J01
H01
G01
F01
I/O
Submit Documentation Feedback
Control. CTL[1:0] are bidirectional control bus signals that are used to indicate the
phase of operation of the PHY link interface. Upon a reset of the interface, this bus is
driven by the PHY. When driven by the PHY, information on CTL[1:0] is synchronous
to PCLK. When driven by the link, information on CTL[1:0] is synchronous to LCLK.
If not implemented, these terminals should be left unconnected.
Overview
29
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 2-9. 1394 Terminals (continued)
BALL NO.
SIGNAL
D0
D1
D2
D3
D4
D5
D6
D7
ZAY
PACKAGE
ZAJ
PACKAGE
J02
K02
K01
L01
L02
L03
M02
M03
H01
H02
J02
J01
K02
K01
L01
M01
I/O
TYPE
DESCRIPTION
I/O
Data. D[7:0] comprise a bidirectional data bus that is used to carry 1394 packet data,
packet speed, and grant type information between the PHY and the link. Upon a
reset of the interface, this bus is driven by the PHY. When driven by the PHY,
information on D[7:0] is synchronous to PCLK. When driven by the link, information
on D[7:0] is synchronous to LCLK. If not implemented, these terminals should be left
unconnected.
Table 2-10. Reserved Terminals
BALL NO.
SIGNAL
ZAY
PACKAGE
ZAJ
PACKAGE
I/O TYPE
RSVD
E12 F12 F13 K12 L12 L13
M11 M12 M13 N10 N11 N12
N13 P03 P10 P11
D11 E11 F12 J11 K10 K11
K12 L10 L11 L12 M05 M11
M12 N11 N12 N13
I/O
RSVD
D12 D13 G12 M08
C10 D12 F11 M09
I
DESCRIPTION
Reserved, do not connect to external signals.
Must be connected to VSS.
Table 2-11. Miscellaneous Terminals
BALL NO.
SIGNAL
I/O
TYPE
ZAY
PACKAGE
ZAJ
PACKAGE
GPIO0
P01
M02
I/O
GPIO1
N02
N01
I/O
GPIO2
P02
L02
I/O
GPIO3
N03
L04
I/O
GPIO4
N04
M03
I/O
DESCRIPTION
General-purpose I/O 0. This terminal functions as a GPIO controlled by bit 0
(GPIO0_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
General-purpose I/O 1. This terminal functions as a GPIO controlled by bit 1
(GPIO1_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
General-purpose I/O 2. This terminal functions as a GPIO controlled by bit 2
(GPIO2_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
General-purpose I/O 3. This terminal functions as a GPIO controlled by bit 3
(GPIO3_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
General-purpose I/O 4. This terminal functions as a GPIO controlled by bit 4
(GPIO4_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
GPIO5
P05
K04
I/O
General-purpose I/O 5. This terminal functions as a GPIO controlled by bit 5
(GPIO5_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
GPIO6
P06
M06
I/O
General-purpose I/O 6. This terminal functions as a GPIO controlled by bit 6
(GPIO6_DIR) in the GPIO control register (see Section 4.60).
GPIO7
N06
L05
I/O
OHCI_PME
P08
M08
O
OHCI power-management event. This is an optional signal that can be used by a
device to request a change in the device or system power state. This signal must be
enabled by software.
CYCLEOUT
N08
L09
O
Cycle out. This terminal provides an 8-kHz cycle timer synchronization signal. If not
implemented, this terminal should be left unconnected.
Note: This terminal has an internal active pullup resistor.
General-purpose I/O 7. This terminal functions as a GPIO controlled by bit 7
(GPIO7_DIR) in the GPIO control register (see Section 4.60).
Note: This terminal has an internal active pullup resistor.
30
Overview
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 2-11. Miscellaneous Terminals (continued)
BALL NO.
SIGNAL
I/O
TYPE
DESCRIPTION
ZAY
PACKAGE
ZAJ
PACKAGE
PD
B03
B03
I
Power down. A high on this terminal turns off all internal circuitry, except the
cable-active monitor circuits that control the CNA output. Asserting PD high also
activates an internal pulldown to force a reset of the internal control logic. If PD is
not used, this terminal must be connected to VSS.
GRST
C13
C12
I
Global power reset. This reset brings all of the XIO2213B internal link registers to
their default states. This should be a one-time power-on reset. This terminal has
hysteresis and an integrated pullup resistor.
SCL
J13
G12
I/O
Serial-bus clock. This signal is used as a serial bus clock when a pullup is detected
on SDA or when the SBDETECT bit is set in the serial bus control and status
register.
Note: This terminal has an internal active pullup resistor.
SDA
H12
H11
I/O
Serial-bus data. This signal is used as serial bus data when a pullup is detected on
SDA or when the SBDETECT bit is set in the serial bus control and status register.
Note: In serial-bus mode, an external pullup resistor is required to prevent the SDA
signal from floating.
BMODE
A05
B06
I
Beta mode. This terminal determines the PHY-section/LLC-section interface
connection protocol. When logic high (asserted), the PHY-section/LLC-section
interface complies with the IEEE Std 1394b-2002 Revision 1.33 beta interface.
When logic low (deasserted), the PHY-section/LLC-section interface complies with
legacy IEEE Std 1394a-2000. This terminal must be pulled high with a 1-kΩ resistor
during normal operation.
TESTM
B02
A03
I
Test control. This input is used in the manufacturing test of the XIO2213B. For
normal use, this terminal must be pulled high through a 1-kΩ resistor to VDD.
VREG_PD
A06
B07
I
Voltage regulator power-down input. When asserted logic high, this pin will
power-down the internal 3.3- to 1.95V regulator. For single 3.3V supply operation,
this pin should be tied to GND. When using the internal regulator, the XIO2213B can
support a maximum of 2-Beta and 1-DS connection simultaneously. If 3-Beta ports
are required to be simultaneously supported, it is recommended to use an external
1.95V regulator.
SE
P13
M10
I
Test control. This input is used in the manufacturing test of the XIO2213B. For
normal use, this terminal must be pulled low either through a 1-kΩ resistor to GND
or directly to GND.
SM
P14
N10
I
Test control. This input is used in the manufacturing test of the XIO2213B. For
normal use, this terminal must be pulled low either through a 1-kΩ resistor to GND
or directly to GND.
Submit Documentation Feedback
Overview
31
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3
www.ti.com
Feature/Protocol Descriptions
This chapter provides a high-level overview of all significant device features. Figure 3-1 shows a simplified
block diagram of the basic architecture of the PCIe to PCI bridge with 1394b OHCI and 3-port PHY. The
top of the diagram is the PCIe interface, and the 1394b OHCI with 3-port PHY is located at the bottom of
the diagram.
PCI Express
Transmitter
PCI Express
Receiver
Power
Mgmt
GPIO
Configuration and
Memory Register
Clock
Generator
Serial
EEPROM
Reset
Controller
PCI Bus Interface
1394b OHCI with 3-Port PHY
1394 Cable Port
1394 Cable Port
1394 Cable Port
Figure 3-1. XIO2213B Block Diagram
3.1
Power-Up/Power-Down Sequencing
The bridge contains both 1.5-V and 3.3-V power terminals. The following power-up and power-down
sequences describe how power is applied to these terminals.
In addition, the bridge has three resets: PERST, GRST, and an internal power-on reset. These resets are
described in Section 3.2. The following power-up and power-down sequences describe how PERST is
applied to the bridge.
The application of the PCIe reference clock (REFCLK) is important to the power-up/-down sequence and
is included in the following power-up and power-down descriptions.
32
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
3.1.1
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Power-Up Sequence
1.
2.
3.
4.
Assert PERST to the device.
Apply 1.5-V and 3.3-V voltages.
Apply a stable PCIe reference clock.
To meet PCIe specification requirements, PERST cannot be deasserted until the following two delay
requirements are satisfied:
– Wait a minimum of 100 s after applying a stable PCIe reference clock. The 100-s limit satisfies the
requirement for stable device clocks by the deassertion of PERST.
– Wait a minimum of 100 ms after applying power. The 100-ms limit satisfies the requirement for
stable power by the deassertion of PERST.
See the power-up sequencing diagram in Figure 3-2.
VDD_15 and
VDDA_15
VDD_33 and
VDDA_33
REFCLK
PERST
100 ms
100 ms
Figure 3-2. Power-Up Sequence
Submit Documentation Feedback
Feature/Protocol Descriptions
33
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.1.2
www.ti.com
Power-Down Sequence
1. Assert PERST to the device.
2. Remove the reference clock.
3. Remove 3.3-V and 1.5-V voltages.
See the power-down sequencing diagram in Figure 3-3. If the VDD_33_AUX terminal is to remain
powered after a system shutdown, the bridge power-down sequence is the same as shown in Figure 3-3.
VDD_15 and
VDDA_15
VDD_33 and
VDDA_33
REFCLK
PERST
Figure 3-3. Power-Down Sequence
34
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
3.2
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
XIO2213B Reset Features
There are five XIO2213B reset options that include internally-generated power-on reset, resets generated
by asserting input terminals, and software-initiated resets that are controlled by sending a PCIe hot reset
or setting a configuration register bit. Table 3-1 identifies these reset sources and describes how the
XIO2213B responds to each reset.
Table 3-1. XIO2213B Reset Options
RESET
OPTION
XIO2213B
internallygenerated
power-on reset
XIO2213B FEATURE
RESET RESPONSE
During a power-on cycle, the XIO2213B asserts an internal
reset and monitors the VDD_15_COMB (B11) terminal. When
this terminal reaches 90% of the nominal input voltage
specification, power is considered stable. After stable power,
the XIO2213B monitors the PCIe reference clock (REFCLK)
and waits 10 s after active clocks are detected. Then,
internal power-on reset is deasserted.
When the internal power-on reset is asserted, all control
registers, state machines, sticky register bits, and power
management state machines are initialized to their default
state.
In addition, the XIO2213B asserts the internal PCI bus
reset.
PCIe reset input This XIO2213B input terminal is used by an upstream PCIe
(PERST, B12) device to generate a PCIe reset and to signal a system
power good condition.
When PERST is asserted low, the XIO2213B generates an
internal PCIe reset as defined in the PCI Express
Specification.
When PERST is asserted low, all control register bits that
are not sticky are reset. Within the configuration register
maps, the sticky bits are indicated by the symbol. Also, all
state machines that are not associated with sticky
functionality are reset.
When PERST transitions from low to high, a system power
good condition is assumed by the XIO2213B.
In addition, the XIO2213B asserts the internal PCI bus
reset.
Note: The system must assert PERST before power is
removed, before REFCLK is removed or before REFCLK
becomes unstable.
When the rising edge of PERST occurs, the XIO2213B
samples the state of all static control inputs and latches
the information internally. If an external serial EEPROM is
detected, a download cycle is initiated. Also, the process to
configure and initialize the PCIe link is started. The
XIO2213B starts link training within 80 ms after PERST is
deasserted.
PCIe training
The XIO2213B responds to a training control hot reset
control hot reset received on the PCIe interface. After a training control hot
reset, the PCIe interface enters the DL_DOWN state.
In the DL_DOWN state, all remaining configuration register
bits and state machines are reset. All remaining bits
exclude sticky bits and EEPROM loadable bits. All
remaining state machines exclude sticky functionality and
EEPROM functionality.
Within the configuration register maps, the sticky bits are
reset by a global reset (GRST) or the internally-generated
power-on reset and EEPROM loadable bits are rest by a
PCIe reset (PERST), GRST, or internally generated
power-on reset.
In addition, the XIO2213B asserts the internal PCI bus
reset.
PCI bus reset
System software has the ability to assert and deassert the
PCI bus reset on the secondary PCI bus interface.
Submit Documentation Feedback
When bit 6 (SRST) in the XIO2213B control register at
offset 3Eh (see Section 4.30) is asserted, the XIO2213B
asserts the internal PCI bus reset. A 0b in the SRST bit
deasserts the PCI bus reset.
Feature/Protocol Descriptions
35
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.3
3.3.1
www.ti.com
PCI Express (PCIe) Interface
External Reference Clock
The XIO2213B requires either a differential, 100-MHz common clock reference or a single-ended,
125-MHz clock reference. The selected clock reference must meet all PCI Express Electrical Specification
requirements for frequency tolerance, spread-spectrum clocking, and signal electrical characteristics.
If the REFCLK_SEL input is connected to VSS, a differential, 100-MHz common clock reference is
expected by the XIO2213B. If the REFCLK_SEL terminal is connected to VDD_33, a single-ended 125-MHz
clock reference is expected by the XIO2213B.
When the single-ended, 125-MHz clock reference option is enabled, the single-ended clock signal is
connected to the REFCLK+ terminal. The REFCLK terminal is connected to one side of an external
capacitor with the other side of the capacitor connected to VSS.
When using a single-ended reference clock, care must be taken to ensure interoperability from a system
jitter standpoint. The PCI Express Base Specification does not ensure interoperability when using a
differential reference clock commonly used in PC applications along with a single-ended clock in a
noncommon clock architecture. System jitter budgets will have to be verified to ensure interoperability (see
the PCI Express Jitter and BER white paper from PCI-SIG).
3.3.2
Beacon and Wake
Since the 1394b OHCI function in the XIO2213B does not support PME from D3cold, it is not necessary
for the PCIe to PCI bridge portion of the design to support beacon generation or WAKE signaling. As a
result, the XIO2213B does not implement VAUX power support.
3.3.3
Initial Flow Control Credits
The bridge flow control credits are initialized using the rules defined in the PCI Express Base
Specification. Table 3-2 identifies the initial flow control credit advertisement for the bridge.
Table 3-2. Initial Flow Control Credit Advertisements
CREDIT TYPE
36
INITIAL ADVERTISEMENT
Posted request headers (PH)
8
Posted request data (PD)
128
Nonposted header (NPH)
4
Nonposted data (NPD)
4
Completion header (CPLH)
0 (infinite)
Completion data (CPLD)
0 (infinite)
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
3.3.4
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
PCIe Message Transactions
PCIe messages are both initiated and received by the bridge. Table 3-3 outlines message support within
the bridge.
Table 3-3. Messages Supported by Bridge
MESSAGE
SUPPORTED
BRIDGE ACTION
Assert_INTx
Yes
Transmitted upstream
Deassert_INTx
Yes
Transmitted upstream
PM_Active_State_Nak
Yes
Received and processed
PM_PME
Yes
Transmitted upstream
PME_Turn_Off
Yes
Received and processed
PME_TO_Ack
Yes
Transmitted upstream
ERR_COR
Yes
Transmitted upstream
ERR_NONFATAL
Yes
Transmitted upstream
ERR_FATAL
Yes
Transmitted upstream
Set_Slot_Power_Limit
Yes
Received and processed
Unlock
No
Discarded
Hot plug messages
No
Discarded
Advanced switching messages
No
Discarded
Vendor defined type 0
No
Unsupported request
Vendor defined type 1
No
Discarded
All supported message transactions are processed per the PCI Express Base Specification.
Submit Documentation Feedback
Feature/Protocol Descriptions
37
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.4
www.ti.com
PCI Interrupt Conversion to PCIe Messages
The bridge converts interrupts from the PCI bus sideband interrupt signals to PCIe interrupt messages.
Since the 1394a OHCI only generates INTA interrupts, only PCIe INTA messages are generated by the
bridge.
PCIe Assert_INTA messages are generated when the 1394a OHCI signals an INTA interrupt. The
requester ID portion of the Assert_INTA message uses the value stored in the primary bus number
register (see Section 4.12) as the bus number, 0 as the device number, and 0 as the function number.
The tag field for each Assert_INTA message is 00h.
PCIe Deassert_INTA messages are generated when the 1394a OHCI deasserts the INTA interrupt. The
requester ID portion of the Deassert_INTA message uses the value stored in the primary bus number
register as the bus number, 0 as the device number, and 0 as the function number. The Tag field for each
Deassert_INTA message is 00h.
Figure 3-4 and Figure 3-5 show the format for both the assert and deassert INTA messages.
+0
7
Byte 0>
R
6
5
+1
3
4
1
1
0
1
1
7
6
5
4
0
0
R
0
0
+3
+2
3
2
0
1
TC
Type
Fmt
0
2
0
Reserved
0
7
6
5
T
E
Attr
D
P
0
3
4
2
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
3
2
1
0
0
0
0
0
1
0
0
Length
R
0
1
0
0
0
0
0
0
0
Code
Byte 4>
Reserved ID
Tag
Byte 8>
Byte 12>
0
0
1
0
Reserved
Figure 3-4. PCIe Assert_INTA Message
+0
7
Byte 0>
Byte 4>
R
6
5
4
+1
3
1
1
0
1
0
1
7
6
5
4
0
0
R
0
0
0
+3
+2
3
2
0
1
TC
Type
Fmt
0
2
Reserved
7
6
5
T
E
Attr
D
P
0
4
3
0
2
R
1
0
7
6
5
4
Length
0
0
0
0
0
0
Code
Reserved ID
Byte 8>
Byte 12>
Tag
0
0
1
0
0
Reserved
Figure 3-5. PCIe Deassert_INTX Message
38
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
3.5
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Two-Wire Serial-Bus Interface
The bridge provides a two-wire serial-bus interface to load subsystem identification information and
specific register defaults from an external EEPROM. The serial-bus interface signals are SCL and SDA.
3.5.1
Serial-Bus Interface Implementation
To enable the serial-bus interface, a pullup resistor must be implemented on the SDA signal. At the rising
edge of PERST or GRST, whichever occurs later in time, the SDA terminal is checked for a pullup
resistor. If one is detected, bit 3 (SBDETECT) in the serial-bus control and status register (see
Section 4.59) is set. Software may disable the serial-bus interface at any time by writing a 0b to the
SBDETECT bit. If no external EEPROM is required, the serial-bus interface is permanently disabled by
attaching a pulldown resistor to the SDA signal.
The bridge implements a two-terminal serial interface with one clock signal (SCL) and one data signal
(SDA). The SCL signal is a unidirectional output from the bridge and the SDA signal is bidirectional. Both
are open-drain signals and require pullup resistors. The bridge is a bus master device and drives SCL at
approximately 60 kHz during data transfers and places SCL in a high-impedance state (0 frequency)
during bus idle states. The serial EEPROM is a bus slave device and must acknowledge a slave address
equal to A0h. Figure 3-6 shows an example application implementing the two-wire serial bus.
VDD_33
Serial
EEPROM
XIO2213B
A0
A1
SCL
SCL
A2
SDA
SDA
Figure 3-6. Serial EEPROM Application
Submit Documentation Feedback
Feature/Protocol Descriptions
39
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.5.2
www.ti.com
Serial-Bus Interface Protocol
All data transfers are initiated by the serial-bus master. The beginning of a data transfer is indicated by a
start condition, which is signaled when the SDA line transitions to the low state while SCL is in the high
state (see Figure 3-7). The end of a requested data transfer is indicated by a stop condition, which is
signaled by a low-to-high transition of SDA while SCL is in the high state (see Figure 3-7). Data on SDA
must remain stable during the high state of the SCL signal, as changes on the SDA signal during the high
state of SCL are interpreted as control signals, that is, a start or stop condition.
SDA
SCL
Start
Condition
Stop
Condition
Change of
Data Allowed
Data Line Stable,
Data Valid
Figure 3-7. Serial-Bus Start/Stop Conditions and Bit Transfers
Data is transferred serially in 8-bit bytes. During a data transfer operation, the exact number of bytes that
are transmitted is unlimited. However, each byte must be followed by an acknowledge bit to continue the
data transfer operation. An acknowledge (ACK) is indicated by the data byte receiver pulling the SDA
signal low, so that it remains low during the high state of the SCL signal. Figure 3-8 shows the
acknowledge protocol.
SCL From
Master
1
2
3
7
8
9
SDA Output
By Transmitter
SDA Output
By Receiver
Figure 3-8. Serial-Bus Protocol Acknowledge
The bridge performs three basic serial-bus operations: single-byte reads, single-byte writes, and multibyte
reads. The single-byte operations occur under software control. The multibyte read operations are
performed by the serial EEPROM initialization circuitry immediately after a PCIe reset (see Section 3.5.3,
Serial-Bus EEPROM Application, for details on how the bridge automatically loads the subsystem
identification and other register defaults from the serial-bus EEPROM.
Figure 3-9 shows a single-byte write. The bridge issues a start condition and sends the 7-bit slave device
address, and the R/W command bit is equal to 0b. A 0b in the R/W command bit indicates that the data
transfer is a write. The slave device acknowledges if it recognizes the slave address. If no
acknowledgment is received by the bridge, bit 1 (SB_ERR) is set in the serial-bus control and status
register (PCI offset B3h, see Section 4.59). Next, the EEPROM word address is sent by the bridge, and
another slave acknowledgment is expected. Then the bridge delivers the data-byte most significant bit
(MSB) first and expects a final acknowledgment before issuing the stop condition.
40
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
b6 b5 b4 b3 b2 b1 b0
S
Data Byte
Word Address
Slave Address
0
A
b7 b6 b5 b4 b3 b2 b1 b0
A
b7 b6 b5 b4 b3 b2 b1 b0
A
P
R/W
A = Slave Acknowledgement
S/P = Start/Stop Condition
Figure 3-9. Serial-Bus Protocol Byte Write
Figure 3-10 shows a single-byte read. The bridge issues a start condition and sends the 7-bit slave device
address, and the R/W command bit is equal to 0b (write). The slave device acknowledges if it recognizes
the slave address. Next, the EEPROM word address is sent by the bridge, and another slave
acknowledgment is expected. Then, the bridge issues a restart condition followed by the 7-bit slave
address, and the R/W command bit is equal to 1b (read). Once again, the slave device responds with an
acknowledge. Next, the slave device sends the 8-bit data byte, MSB first. Since this is a 1-byte read, the
bridge responds with no acknowledge (logic high) indicating the last data byte. Finally, the bridge issues a
stop condition.
Word Address
Slave Address
b6 b5 b4 b3 b2 b1 b0
S
Start
b7 b6 b5 b4 b3 b2 b1 b0
A
0
Slave Address
b6 b5 b4 b3 b2 b1 b0
S
A
Restart
R/W
A
1
R/W
Data Byte
b7 b6 b5 b4 b3 b2 b1 b0
M
P
Stop
M = Master Acknowledgement
A = Slave Acknowledgement
S/P = Start/Stop Condition
Figure 3-10. Serial-Bus Protocol Byte Read
Figure 3-11 shows the serial interface protocol during a multibyte serial EEPROM download. The
serial-bus protocol starts exactly the same as a 1-byte read. The only difference is that multiple data bytes
are transferred. The number of transferred data bytes is controlled by the bridge master. After each data
byte, the bridge master issues acknowledge (logic low) if more data bytes are requested. The transfer
ends after a bridge master no acknowledge (logic high) followed by a stop condition.
Word Address
Slave Address
S
1
0
1
0
0
0
0
Start
0
A
0
0
0
0
0
0
Slave Address
0
0
M
A = Slave Acknowledgement
S
1
0
0
1
0
Restart
R/W
Data Byte 0
A
Data Byte 1
M
Data Byte 2
M = Master Acknowledgement
M
0
0
1
A
R/W
Data Byte 3
M
P
S/P = Start/Stop Condition
Figure 3-11. Serial-Bus Protocol Multibyte Read
Bit 7 (PROT_SEL) in the serial-bus control and status register changes the serial-bus protocol. Each of
the three previous serial-bus protocol figures show the PROT_SEL bit default (logic low). When this
control bit is asserted, the word address and corresponding acknowledge are removed from the serial-bus
protocol. This feature allows the system designer a second serial-bus protocol option when selecting
external EEPROM devices.
Submit Documentation Feedback
Feature/Protocol Descriptions
41
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.5.3
www.ti.com
Serial-Bus EEPROM Application
The registers and corresponding bits that are loaded through the EEPROM are provided in Table 3-4.
Table 3-4. EEPROM Register Loading Map
SERIAL EEPROM
WORD ADDRESS
BYTE DESCRIPTION
00h
PCIe to PCI bridge function indicator (00h)
01h
Number of bytes to download (1Eh)s
02h
PCI 84h, subsystem vendor ID, byte 0
03h
PCI 85h, subsystem vendor ID, byte 1
04h
PCI 86h, subsystem ID, byte 0s
05h
PCI 87h, subsystem ID, byte 1s
06h
PCI D4h, general control, byte 0
07h
PCI D5h, general control, byte 1
08h
PCI D6h, general control, byte 2
09h
PCI D7h, general control, byte 3
0Ah
TI Proprietary register load 00h (PCI D8h)
0Bh
TI Proprietary register load 00h (PCI D9h)
0Ch
Reserved — no bits loaded 00h (PCI DAh)
0Dh
PCI DCh, arbiter control
0Eh
PCI DDh, arbiter request mask
0Fh
PCI C0h, TL control and diagnostic register, byte 0
10h
PCI C0h, TL control and diagnostic register, byte 1
11h
PCI C0h, TL control and diagnostic register, byte 2
12h
PCI C0h, TL control and diagnostic register, byte 3
13h
PCI C4h, DLL control and diagnostic register, byte 0
14h
PCI C5h, DLL control and diagnostic register, byte 1
15h
PCI C6h, DLL control and diagnostic register, byte 2
16h
PCI C7h, DLL control and diagnostic register, byte 3
17h
PCI C8h, PHY control and diagnostic register, byte 0
18h
PCI C9h, PHY control and diagnostic register, byte 1
19h
PCI CAh, PHY control and diagnostic register, byte 2
1Ah
PCI CBh, PHY control and diagnostic register, byte 3
1Bh
Reserved — no bits loaded 00h (PCI CEh)
1Ch
Reserved — no bits loaded 00h (PCI CFh)
1Dh
TI proprietary register load 00h (PCI E0h)
1Eh
TI proprietary register load 00h (PCI E2h)
1Fh
TI proprietary register load 00h (PCI E3h)
20h
1394 OHCI function indicator (01h)
21h
22h
PCI 3Eh, minimum grant, bits 3-0
23h
PCI 2Ch, subsystem vendor ID, byte 0
24h
PCI 2Dh, subsystem vendor ID, byte 1
25h
PCI 2Eh, subsystem ID, byte 0
26h
PCI 2Fh, subsystem ID, byte 1
27h
42
Number of bytes (18h)
PCI 3Fh, maximum latency, bits 7-4
[7]
Link_Enh enab_unfair
Feature/Protocol Descriptions
[6]
HC Control
Program Phy
Enable
[5:3]
RSVD
[2]
Link_Enh
[1]
Link_Enh enab_accel
[0]
RSVD
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 3-4. EEPROM Register Loading Map (continued)
SERIAL EEPROM
WORD ADDRESS
BYTE DESCRIPTION
28h
Mini-ROM address, this byte indicates the MINI ROM offset into the EEPROM
00h = No MINI ROM
01h to FFh = MINI ROM offset
29h
OHCI 24h, GUIDHi, byte 0
2Ah
OHCI 25h, GUIDHi, byte 1
2Bh
OHCI 26h, GUIDHi, byte 2
2Ch
OHCI 27h, GUIDHi, byte 3
2Dh
OHCI 28h, GUIDLo, byte 0
2Eh
OHCI 29h, GUIDLo, byte 1
2Fh
OHCI 2Ah, GUIDLo, byte 2
30h
OHCI 2Bh, GUIDLo, byte 3
31h
Reserved — no bits loaded
32h
PCI F5h, Link_Enh, byte 1, bits 7, 6, 5, 4
33h
PCI F0h, PCI miscellaneous, byte 0, bits 7, 4, 2, 1, 0
34h
PCI F1h, PCI miscellaneous, byte 1, bits 1, 0
35h
Reserved — no bits loaded
36h
Reserved — no bits loaded
37h
Reserved — no bits loaded
38h
Reserved — no bits loaded
39h
Reserved multifunction select register
3Ah
End-of-list indicator (80h)
This format must be explicitly followed for the bridge to correctly load initialization values from a serial
EEPROM. All byte locations must be considered when programming the EEPROM.
The serial EEPROM is addressed by the bridge at slave address 1010 000b. This slave address is
internally hardwired and cannot be changed by the system designer. Therefore, all three hardware
address bits for the EEPROM are tied to VSS to achieve this address. The serial EEPROM in the sample
application circuit (Figure 3-6) assumes the 1010b high-address nibble. The lower three address bits are
terminal inputs to the chip, and the sample application shows these terminal inputs tied to VSS.
During an EEPROM download operation, bit 4 (ROMBUSY) in the serial-bus control and status register is
asserted. After the download is finished, bit 0 (ROM_ERR) in the serial-bus control and status register
may be monitored to verify a successful download.
Submit Documentation Feedback
Feature/Protocol Descriptions
43
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.5.4
www.ti.com
Accessing Serial-Bus Devices Through Softwaree
The bridge provides a programming mechanism to control serial-bus devices through system software.
The programming is accomplished through a doubleword of PCI configuration space at offset B0h.
Table 3-5 lists the registers that program a serial-bus device through software.
Table 3-5. Registers Used To Program Serial-Bus Devices
PCI OFFSET
REGISTER NAME
DESCRIPTION
B0h
Serial-bus data
(see Section 4.56)
Contains the data byte to send on write commands or the received data byte on read
commands.
B1h
Serial-bus word address
(see Section 4.57)
The content of this register is sent as the word address on byte writes or reads. This register is
not used in the quick command protocol. Bit 7 (PROT_SEL) in the serial-bus control and status
register (offset B3h, see Section 4.59) is set to 1b to enable the slave address to be sent.
B2h
Serial-bus slave address
(see Section 4.58)
Write transactions to this register initiate a serial-bus transaction. The slave device address and
the R/W command selector are programmed through this register.
B3h
Serial-bus control and
status (see Section 4.59)
Serial interface enable, busy, and error status are communicated through this register. In
addition, the protocol-select bit (PROT_SEL) and serial-bus test bit (SBTEST) are programmed
through this register.
To access the serial EEPROM through the software interface, the following steps are performed:
1. The control and status byte is read to verify the EEPROM interface is enabled (SBDETECT asserted)
and not busy (REQBUSY and ROMBUSY deasserted).
2. The serial-bus word address is loaded. If the access is a write, the data byte is also loaded.
3. The serial-bus slave address and R/W command selector byte is written.
4. REQBUSY is monitored until this bit is deasserted.
5. SB_ERR is checked to verify that the serial-bus operation completed without error. If the operation is a
read, the serial-bus data byte is now valid.
3.6
Advanced Error Reporting Registers
In the extended PCIe configuration space, the bridge supports the advanced error reporting capabilities
structure. For the PCIe interface, both correctable and uncorrectable error statuses are provided. For the
PCI bus interface, secondary uncorrectable error status is provided. All uncorrectable status bits have
corresponding mask and severity control bits. For correctable status bits, only mask bits are provided.
Both the primary and secondary interfaces include first error pointer and header log registers. When the
first error is detected, the corresponding bit position within the uncorrectable status register is loaded into
the first error pointer register. Likewise, the header information associated with the first failing transaction
is loaded into the header log. To reset this first error control logic, the corresponding status bit in the
uncorrectable status register is cleared by a writeback of 1b.
For systems that require high data reliability, ECRC is fully supported on the PCIe interface. The
primary-side advanced error capabilities and control register has both ECRC generation and checking
enable control bits. When the checking bit is asserted, all received TLPs are checked for a valid ECRC
field. If the generation bit is asserted, all transmitted TLPs contain a valid ECRC field.
3.7
Data Error Forwarding Capability
The bridge supports the transfer of data errors in both directions.
If a downstream PCIe transaction with a data payload is received that targets the internal PCI bus and the
EP bit is set indicating poisoned data, the bridge must ensure that this information is transferred to the PCI
bus. To do this, the bridge forces a parity error on each PCI bus data phase by inverting the parity bit
calculated for each double word of data.
If the bridge is the target of a PCI transaction that is forwarded to the PCIe interface and a data parity
error is detected, this information is passed to the PCIe interface. To do this, the bridge sets the EP bit in
the upstream PCIe header.
44
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
3.8
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
General-Purpose I/O (GPIO) Interface
Up to eight GPIO terminals are provided for system customization. These GPIO terminals are 3.3-V
tolerant.
The exact number of GPIO terminals varies based on implementing the clock-run, power-override, and
serial EEPROM interface features. These features share four of the eight GPIO terminals. When any of
the three shared functions are enabled, the associated GPIO terminal is disabled.
All eight GPIO terminals are individually configurable as either inputs or outputs by writing the
corresponding bit in the GPIO control register at offset B4h. A GPIO data register at offset B6h exists to
either read the logic state of each GPIO input or to set the logic state of each GPIO output. The power-up
default state for the GPIO control register is input mode.
3.9
Set Slot Power Limit Functionality
The PCI Express Specification provides a method for devices to limit internal functionality and save power
based on the value programmed into the captured slot power limit scale (CSPLS) and capture slot power
limit value (CSPLV) fields of the PCIe device capabilities register at offset 94h (see Section 4.50, Device
Capabilities Register, for details). The bridge writes these fields when a set slot power limit message is
received on the PCIe interface.
After the deassertion of PERST, the XIO2213B compares the information within the CSPLS and CSPLV
fields of the device capabilities register to the minimum power scale (MIN_POWER_SCALE) and minimum
power value (MIN_POWER_VALUE) fields in the general control register at offset D4h (see Section 4.66,
General Control Register, for details). If the CSPLS and CSPLV fields are less than the
MIN_POWER_SCALE and MIN_POWER_VALUE fields, respectively, the bridge takes the appropriate
action that is defined below.
The power usage action is programmable within the bridge. The general control register includes a 3-bit
POWER_OVRD field. This field is programmable to the following two options:
• Ignore slot power limit fields.
• Respond with unsupported request to all transactions except type 0/1 configuration transactions, and
set slot power limit messages.
3.10 PCIe and PCI Bus Power Management
The bridge supports both software-directed power management and active-state power management
through standard PCI configuration space. Software-directed registers are located in the power
management capabilities structure located at offset 50h. Active-state power management control registers
are located in the PCIe capabilities structure located at offset 90h.
During software-directed power-management state changes, the bridge initiates link state transitions to L1
or L2/L3 after a configuration write transaction places the device in a low-power state. The
power-management state machine is also responsible for gating internal clocks based on the power state.
Table 3-6 identifies the relationship between the D-states and bridge clock operation.
Table 3-6. Clocking In Low Power States
CLOCK SOURCE
D0/L0
D1/L1
D2/L1
D3/L2/L3
PCIe reference clock input (REFCLK)
On
On
On
On/Off
Internal PCI bus clock to bridge function
On
Off
Off
Off
Internal PCI bus clock to 1394b OHCI function
On
On
On
On/Off
Submit Documentation Feedback
Feature/Protocol Descriptions
45
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
The link power management (LPM) state machine manages active-state power by monitoring the PCIe
transaction activity. If no transactions are pending and the transmitter has been idle for at least the
minimum time required by the PCI Express Specification, the LPM state machine transitions the link to
either the L0s or L1 state. By reading the bridges L0s and L1 exit latency in the link capabilities register,
the system software may make an informed decision relating to system performance versus power
savings. The ASLPMC field in the link control register provides an L0s-only option, L1-only option, or both
L0s and L1 options.
Finally, the bridge generates the PM_Active_State_Nak Message if a PM_Active_State_Request_L1
DLLP is received on the PCIe interface and the link cannot be transitioned to L1.
46
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
3.11 1394b OHCI Controller Functionality
3.11.1 1394b OHCI Power Management
The 1394b OHCI controller complies with the PCI Bus Power Management Interface Specification. The
controller supports the D0 (uninitialized), D0 (active), D1, D2, and D3 power states as defined by the
power-management definition in the 1394 Open Host Controller Interface Specification, Appendix A4.
Table 3-7 identifies the supported power-management registers within the 1394 OHCI configuration
register map.
Table 3-7. 1394b OHCI Configuration Register Map
REGISTER NAME
Power management capabilities
PM data
Power management control/status register bridge support extensions
OFFSET
Next item pointer
Capability ID
Power management control/status (CSR)
44h
48h
3.11.2 1394b OHCI and VAUX
The 1394b OHCI function within the XIO2213B is powered by VDD_MAIN only. Therefore, during the D3cold
power-management state, VAUX is not supplied to the 1394b OHCI function.
This implies that the 1394b OHCI function does not implement sticky bits must be initialized after a D3cold
power-management state. An external serial EEPROM interface is available to initialize critical
configuration register bits. The EEPROM download is triggered by the deassertion of the PERST input.
Otherwise, the BIOS must initialize the 1394b OHCI function.
3.11.3 1394b OHCI and Reset Options
The 1394b OHCI function is completely reset by the internal power-on reset feature, GRST input, or
PERST input. This includes all EEPROM loadable bits, power-management functions, and all remaining
configuration register bits and logic.
A PCIe training control hot reset or the PCI bus configuration register reset bit (SRST) excludes the
EEPROM loadable bits, power-management functions, and 1394 PHY. All remaining configuration
registers and logic are reset.
If the OHCI controller is in the power-management D2 or D3 state, or if the OHCI configuration register
reset bit (SoftReset) is set, the OHCI controller DMA logic and link logic is reset.
Finally, if the OHCI configuration register PHY reset bit (ISBR) is set, the 1394 PHY logic is reset.
3.11.4 1394b OHCI PCI Bus Master
As a bus master, the 1394 OHCI function supports the memory commands specified in Table 3-8. The
commands include memory read, memory read line, memory read multiple, memory write, and memory
write and invalidate.
The read command usage for read transactions of greater than two data phases are determined by the
selection in bits 9:8 (MR_ENHANCE field) of the PCI miscellaneous configuration register at offset F0h
(see Section 7.21). For read transactions of one or two data phases, a memory read command is used.
The write command usage is determined by the MWI_ENB bit 4 of the command configuration register at
offset 04h (see Section 4.3). If bit 4 is asserted and a memory write starts on a cache boundary with a
length greater than one cache line, memory write and invalidate commands are used. Otherwise, memory
write commands are used.
Submit Documentation Feedback
Feature/Protocol Descriptions
47
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 3-8. 1394 OHCI Memory Command Options
PCI
COMMAND
C/BE3C/BE0
OHCI MASTER FUNCTION
DMA read from memory
Memory read
0110
Memory write
0111
DMA write to memory
Memory read multiple
1100
DMA read from memory
Memory read line
1110
DMA read from memory
Memory write and invalidate
1111
DMA write to memory
3.11.5 1394b OHCI Subsystem Identification
The subsystem identification register at offset 2Ch is used for system and option card identification
purposes. This register can be initialized from the serial EEPROM or programmed via the subsystem
access register at offset F8h in the 1394a OHCI PCI configuration space (see Section 7.23).
Write access to the subsystem access register updates the subsystem identification registers identically to
OHCI-Lynx™ integrated circuits. The contents of the subsystem access register are aliased to the
subsystem vendor ID and subsystem ID registers at PCI offsets 2Ch and 2Eh, respectively. The
subsystem ID value written to this register may also be read back from this register.
3.11.6 1394b OHCI PME Support
Since the 1394b OHCI controller is not connected to VAUX, PME generation is disabled for D3cold
power-management states.
48
Feature/Protocol Descriptions
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
4
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Classic PCI Configuration Space
The programming model of the XIO2213B PCIe to PCI bridge is compliant to the classic PCI-to-PCI bridge
programming model. The PCI configuration map uses the type 1 PCI bridge header.
Sticky bits are reset by a global reset (GRST) or the internally-generated power-on reset. EEPROM
loadable bits are reset by a PCIe reset (PERST), GRST, or the internally-generated power-on reset. The
remaining register bits are reset by a PCIe hot reset, PERST, GRST, or the internally-generated power-on
reset.
Table 4-1. Classic PCI Configuration Register Map
REGISTER NAME
OFFSET
Device ID
Vendor ID
000h
Status
Command
004h
Class code
BIST
Header type
Primary latency timer
Revision ID
008h
Cache line size
00Ch
Device contol base address
010h
Scratchpad RAM base address
Secondary latency timer
Subordinate bus number
014h
Secondary bus number
Primary bus number
018h
I/O limit
I/O base
01Ch
Secondary status
Memory limit
Prefetchable memory limit
Memory base
020h
Prefetchable memory base
024h
Prefetchable base upper 32 bits
028h
Prefetchable limit upper 32 bits
02Ch
I/O limit upper 16 bits
I/O base upper 16 bits
Reserved
Capabilities pointer
Reserved
Interrupt pin
Interrupt line
Reserved
Next item pointer
Power management bridge
support extention
PM apability ID
Power management control/status
Reserved
Next item pointer
MSI capability ID
MSI message lower address
Reserved
Reserved
SSID/SSVID capability ID
Subsystem vendor ID (1)
Reserved
080h
084h
088h-08Ch
PCI Express capabilities register
Next item pointer
PCI Express capability ID
Device capabilities
Device status
090h
094h
Device control
Link capabilities
098h
09Ch
Link control
0A0h
Reserved
(1)
06Ch
070h-07Ch
Next item pointer
Subsystem ID (1)
GPIO data
060h
068h
MSI message data
Reserved
(1)
054h
064h
MSI message upper address
Serial-bus slave address (1)
050h
058h-05Ch
MSI message control
Serial-bus control and
status (1)
03Ch
040h-04Ch
Power management capabilities
Link status
034h
038h
Bridge control
Power management data
030h
0A4h-0ACh
Serial-bus word address (1)
Serial-bus data (1)
(1)
GPIO control
0B0h
0B4h
One or more bits in this register are reset by PERST, GRST, or the internally-generated power-on reset.
Submit Documentation Feedback
Classic PCI Configuration Space
49
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 4-1. Classic PCI Configuration Register Map (continued)
REGISTER NAME
OFFSET
Reserved
0B8h-0BCh
Control and diagnostic register 0(1)
0C0h
(1)
0C4h
Control and diagnostic register 1
Control and diagnostic register 2(1)
0C8h
Reserved
0CCh
Subsystem access(1)
0D0h
General control(1)
0D4h
Reserved
TI proprietary(1)
TI proprietary(1)
TI proprietary(1)
0D8h
Reserved
Arbiter time-out status
Arbiter request mask(1)
Arbiter control(1)
0DCh
Reserved
TI proprietary(1)
0E0h
TI proprietary(1)
Reserved
TI proprietary
0E4h
Reserved
4.1
0E8h-0FCh
Vendor ID Register
This 16-bit read-only register contains the value 104Ch, which is the vendor ID assigned to TI.,
PCI register offset:
00h
Register type:
Read-only
Default value:
104Ch
BIT NUMBER
RESET STATE
4.2
15
0
14
0
13
0
12
1
11
0
10
0
9
0
8
0
7
0
6
1
5
0
4
0
3
1
2
1
1
0
0
0
Device ID Register
This 16-bit read-only register contains the value 823Eh, which is the device ID assigned by TI for the
bridge.,
PCI register offset:
02h
Register type:
Read only
Default value:
823Eh
BIT NUMBER
RESET STATE
4.3
15
1
14
0
13
0
12
0
11
0
10
0
9
1
8
0
7
0
6
0
5
1
4
1
3
0
2
0
1
0
0
1
Command Register
The command register controls how the bridge behaves on the PCIe interface. See Table 4-2 for a
complete description of the register contents.
PCI register offset:
04h
Register type:
Read only, Read/Write
Default value:
BIT NUMBER
RESET STATE
50
15
0
0000h
14
0
Classic PCI Configuration Space
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 4-2. Command Register Description
BIT
15:11
FIELD NAME
ACCESS
DESCRIPTION
RSVD
R
Reserved. Returns 00000b when read.
10
INT_DISABLE
R
INTx disable. This bit enables device specific interrupts. Since the bridge does not
generate any internal interrupts, this bit is read-only 0b.
9
FBB_ENB
R
Fast back-to-back enable. The bridge does not generate fast back-to-back transactions;
therefore, this bit returns 0b when read.
8
SERR_ENB
RW
SERR enable. When this bit is set, the bridge can signal fatal and nonfatal errors on the
PCIe interface on behalf of SERR assertions detected on the PCI bus.
0 = Disable the reporting of nonfatal errors and fatal errors (default)
1 = Enable the reporting of nonfatal errors and fatal errors
7
STEP_ENB
R
6
PERR_ENB
RW
Address/data stepping control. The bridge does not support address/data stepping, and
this bit is hardwired to 0b.
Controls the setting of bit 8 (DATAPAR) in the status register (offset 06h, see Section 4.4)
in response to a received poisoned TLP from PCIe. A received poisoned TLP is forwarded
with bad parity to conventional PCI, regardless of the setting of this bit.
0 = Disables the setting of the master data parity error bit (default)
1 = Enables the setting of the master data parity error bit
5
VGA_ENB
R
VGA palette snoop enable. The bridge does not support VGA palette snooping; therefore,
this bit returns 0b when read.
4
MWI_ENB
RW
Memory write and invalidate enable. When this bit is set, the bridge translates PCIe
memory write requests into memory write and invalidate transactions on the PCI interface.
0 = Disable the promotion to memory write and invalidate (default)
1 = Enable the promotion to memory write and invalidate
3
SPECIAL
2
MASTER_ENB
R
RW
Special cycle enable. The bridge does not respond to special cycle transactions; therefore,
this bit returns 0b when read.
Bus master enable. When this bit is set, the bridge is enabled to initiate transactions on
the PCIe interface.
0 = PCIe interface cannot initiate transactions. The bridge must disable the response
to memory and I/O transactions on the PCI interface (default).
1 = PCIe interface can initiate transactions. The bridge can forward memory and I/O
transactions from PCI secondary interface to the PCIe interface.
1
MEMORY_ENB
RW
Memory space enable. Setting this bit enables the bridge to respond to memory
transactions on the PCIe interface.
0 = PCIe receiver cannot process downstream memory transactions and must
respond with an unsupported request (default)
1 = PCIe receiver can process downstream memory transactions. The bridge can
forward memory transactions to the PCI interface.
0
IO_ENB
RW
I/O space enable. Setting this bit enables the bridge to respond to I/O transactions on the
PCIe interface.
0 = PCIe receiver cannot process downstream I/O transactions and must respond
with an unsupported request (default)
1 = PCIe receiver can process downstream I/O transactions. The bridge can forward
I/O transactions to the PCI interface.
Submit Documentation Feedback
Classic PCI Configuration Space
51
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.4
www.ti.com
Status Register
The status register provides information about the PCIe interface to the system. See Table 4-3 for a
complete description of the register contents.
PCI register offset:
06h
Register type:
Read only, Read/Clear
Default value:
0010h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
1
3
0
2
0
1
0
0
0
Table 4-3. Status Register Description
BIT
FIELD NAME
15
PAR_ERR
ACCESS
DESCRIPTION
RCU
Detected parity error. This bit is set when the PCIe interface receives a poisoned TLP. This
bit is set regardless of the state of bit 6 (PERR_ENB) in the command register (offset 04h,
see Section 4.3).
0 = No parity error detected
1 = Parity error detected
14
SYS_ERR
RCU
Signaled system error. This bit is set when the bridge sends an ERR_FATAL or
ERR_NONFATAL message and bit 8 (SERR_ENB) in the command register (offset 04h,
see Section 4.3) is set.
0 = No error signaled
1 = ERR_FATAL or ERR_NONFATAL signaled
13
MABORT
RCU
Received master abort. This bit is set when the PCIe interface of the bridge receives a
completion-with-unsupported-request status.
0 = Unsupported request not received on the PCIe interface
1 = Unsupported request received on the PCIe interface
12
TABORT_REC
RCUT
Received target abort. This bit is set when the PCIe interface of the bridge receives a
completion-with-completer-abort status.
0 = Completer abort not received on the PCIe interface
1 = Completer abort received on the PCIe interface
11
TABORT_SIG
RCUT
Signaled target abort. This bit is set when the PCIe interface completes a request with
completer abort status.
0 = Completer abort not signaled on the PCIe interface
1 = Completer abort signaled on the PCIe interface
10:9
8
PCI_SPEED
DATAPAR
R
RCU
DEVSEL timing. These bits are read-only 00b, because they do not apply to PCIe.
Master data parity error. This bit is set if bit 6 (PERR_ENB) in the command register (offset
04h, see Section 4.3) is set and the bridge receives a completion with data marked as
poisoned on the PCIe interface or poisons a write request received on the PCIe interface.
0 = No uncorrectable data error detected on the primary interface
1 = Uncorrectable data error detected on the primary interface
7
FBB_CAP
R
Fast back-to-back capable. This bit does not have a meaningful context for a PCIe device
and is hardwired to 0b.
6
RSVD
R
Reserved. Returns 0b when read.
5
66MHZ
R
66-MHz capable. This bit does not have a meaningful context for a PCIe device and is
hardwired to 0b.
4
CAPLIST
R
Capabilities list. This bit returns 1b when read, indicating that the bridge supports additional
PCI capabilities.
3
INT_STATUS
R
Interrupt status. This bit reflects the interrupt status of the function. This bit is read-only 0b
since the bridge does not generate any interrupts internally.
RSVD
R
Reserved. Returns 000b when read.
2:0
52
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
4.5
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Class Code and Revision ID Register
This read-only register categorizes the base class, subclass, and programming interface of the bridge. The
base class is 06h, identifying the device as a bridge. The subclass is 04h, identifying the function as a PCI
to PCI bridge, and the programming interface is 00h. Furthermore, the TI device revision is indicated in the
lower byte (00h). See Table 4-4 for a complete description of the register contents.
PCI register offset:
08h
Register type:
Read only
Default value:
0604 0001h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
1
25
1
24
0
23
0
22
0
21
0
20
0
19
0
18
1
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
Table 4-4. Class Code and Revision ID Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
31:24
BASECLASS
R
Base class. This field returns 06h when read, which classifies the function as a bridge device.
23:16
SUBCLASS
R
Subclass. This field returns 04h when read, which classifies the function as a PCI to PCI bridge.
15:8
PGMIF
R
Programming interface. This field returns 00h when read.
7:0
CHIPREV
R
Silicon revision. This field returns the silicon revision of the function.
4.6
Cache Line Size Register
If the EN_CACHE_LINE_CHECK bit in the TL control and diagnostic register is 0, Cheetah- Express shall
use side-band signals from the 1394b OHCI core to determine how much data to fetch when handling
delayed read transactions. In this case, the cache line size register will have no effect on the design and
will essentially be a read/write scratchpad register. If the EN_CACHE_LINE_CHECK bit is 1, the cache
line size register is used by the bridge to determine how much data to prefetch when handling delayed
read transactions. In this case, the value in this register must be programmed to a power of 2, and any
value greater than 32 DWORDs will be treated as 32 DWORDs.
PCI register offset:
0Ch
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
4.7
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Primary Latency Timer Register
This read-only register has no meaningful context for a PCIe device and returns 00h when read.
PCI register offset:
0Dh
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
Submit Documentation Feedback
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Classic PCI Configuration Space
53
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.8
www.ti.com
Header Type Register
This read-only register indicates that this function has a type 1 PCI header. Bit 7 of this register is 0b,
indicating that the bridge is a single-function device.
PCI register offset:
0Eh
Register type:
Read only
Default value:
01h
BIT NUMBER
RESET STATE
4.9
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
BIST Register
Since the bridge does not support a built-in self test (BIST), this read-only register returns the value of 00h
when read.
PCI register offset:
0Fh
Register type:
Read only
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.10 Device Control Base Address Register
This read/write register programs the memory base address that accesses the device control registers.
See Table 4-5 for a complete description of the register contents.
PCI register offset:
10h
Register type:
Read only, Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-5. Device Control Base Address Register Description
BIT
ACCESS
DESCRIPTION
R or RW
Memory address. The memory address field for XIO2213B uses 20 read/write bits indicating
that 4096 bytes of memory space are required. While less than this is actually used, typical
systems will allocate this space on a 4K boundary. If the BAR0_EN bit (bit 5 at C8h) is 0,
these bits are read only and return zeros when read. If the BAR0_EN bit is 1, these bits are
read/write.
ADDRESS
11:4
RSVD
R
Reserved. These bits are read only and return 00h when read.
3
PRE_FETCH
R
Prefetchable. This bit is read-only 0b indicating that this memory window is not prefetchable.
2:1
MEM_TYPE
R
Memory type. This field is read-only 00b indicating that this window can be located anywhere
in the 32-bit address space.
MEM_IND
R
Memory space indicator. This field returns 0b indicating that memory space is used.
0
54
FIELD NAME
31:12
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.11 Scratchpad RAM Base Address
This register is used to program the memory address used to access the embedded scratchpad RAM.
PCI register offset:
14h
Register type:
Read only, Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-6. Device Control Base Address Register Description
BIT
FIELD NAME
31:12
ADDRESS
11:4
ACCESS
DESCRIPTION
R or RW
Memory address. The memory address field for XIO2213B uses 20 read/write bits indicating
that 4096 bytes of memory space are required. If the BAR1_EN bit (bit 6 at C8h) is 0, these
bits are read only and return zeros when read. If the BAR1_EN bit is 1, these bits are
read/write.
RSVD
R
Reserved. These bits are read only and return 00h when read.
3
PRE_FETCH
R
Prefetchable. This bit is read-only 0b indicating that this memory window is not prefetchable.
2:1
MEM_TYPE
R
Memory type. This field is read-only 00b indicating that this window can be located anywhere
in the 32-bit address space.
MEM_IND
R
Memory space indicator. This field returns 0b indicating that memory space is used.
0
4.12 Primary Bus Number Register
This read/write register specifies the bus number of the PCI bus segment that the PCIe interface is
connected to.
PCI register offset:
18h
Register type:
Read/Write
Default value:
BIT NUMBER
RESET STATE
7
0
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.13 Secondary Bus Number Register
This read/write register specifies the bus number of the PCI bus segment that the PCI interface is
connected to. The bridge uses this register to determine how to respond to a type 1 configuration
transaction.
PCI register offset:
19h
Register type:
Read/Write
Default value:
BIT NUMBER
RESET STATE
7
0
Submit Documentation Feedback
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Classic PCI Configuration Space
55
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.14 Subordinate Bus Number Register
This read/write register specifies the bus number of the highest-number PCI bus segment that is
downstream of the bridge. Since the PCI bus is internal and only connects to the 1394a OHCI, this
register must always be equal to the secondary bus number register (offset 19h, see Section 4.13). The
bridge uses this register to determine how to respond to a type 1 configuration transaction.
PCI register offset:
1Ah
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.15 Secondary Latency Timer Register
This read/write register specifies the secondary bus latency timer for the bridge, in units of PCI clock
cycles.
PCI register offset:
1Bh
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.16 I/O Base Register
This read/write register specifies the lower limit of the I/O addresses that the bridge forwards downstream.
See Table 4-7 for a complete description of the register contents.
PCI register offset:
1Ch
Register type:
Read only, Read/Write
Default value:
BIT NUMBER
RESET STATE
7
0
01h
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Table 4-7. I/O Base Register Description
BIT
FIELD NAME
ACCESS
7:4
3:0
56
IOTYPE
R
DESCRIPTION
IOBASE
I/O type. This field is read-only 1h indicating that the bridge supports 32-bit I/O addressing.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.17 I/O Limit Register
This read/write register specifies the upper limit of the I/O addresses that the bridge forwards downstream.
See Table 4-8 for a complete description of the register contents.
PCI register offset:
1Dh
Register type:
Read only, Read/Write
Default value:
01h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Table 4-8. I/O Limit Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
I/O limit. Defines the top address of the I/O address range that determines when to forward I/O
transactions from one interface to the other. These bits correspond to address bits [15:12] in the I/O
address. The lower 12 bits are assumed to be FFFh. The 16 bits corresponding to address bits
[31:16] of the I/O address are defined in the I/O limit upper 16 bits register (offset 32h, see
Section 4.26).
7:4
IOLIMIT
RW
3:0
IOTYPE
R
Submit Documentation Feedback
I/O type. This field is read-only 1h indicating that the bridge supports 32-bit I/O addressing.
Classic PCI Configuration Space
57
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.18 Secondary Status Register
The secondary status register provides information about the PCI bus interface. See Table 4-9 for a
complete description of the register contents.
PCI register offset:
1Eh
Register type:
Read only, Read/Clear
Default value:
02X0h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
1
8
0
7
x
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-9. Secondary Status Register Description
BIT
15
FIELD NAME
PAR_ERR
ACCESS
RCU
DESCRIPTION
Detected parity error. This bit reports the detection of an uncorrectable address, attribute, or data
error by the bridge on its internal PCI bus secondary interface. This bit must be set when any of the
following three conditions are true:
The bridge detects an uncorrectable address or attribute error as a potential target.
The bridge detects an uncorrectable data error when it is the target of a write transaction.
The bridge detects an uncorrectable data error when it is the master of a read transaction
(immediate read data).
The bit is set irrespective of the state of bit 0 (PERR_EN) in the bridge control register at offset 3Eh
(see Section 4.30).
0 = Uncorrectable address, attribute, or data error not detected on secondary interface
1 = Uncorrectable address, attribute, or data error detected on secondary interface
14
SYS_ERR
RCU
Received system error. This bit is set when the bridge detects an SERR assertion.
0 = No error asserted on the PCI interface
1 = SERR asserted on the PCI interface
13
MABORT
RCU
Received master abort. This bit is set when the PCI interface of the bridge reports the detection of a
master abort termination by the bridge when it is the master of a transaction on its secondary
interface.
0 = Master abort not received on the PCI interface
1 = Master abort received on the PCI interface
12
TABORT_REC
RCU
Received target abort. This bit is set when the PCI interface of the bridge receives a target abort.
0 = Target abort not received on the PCI interface
1 = Target abort received on the PCI interface
11
TABORT_SIG
RCU
Signaled target abort. This bit reports the signaling of a target abort termination by the bridge when it
responds as the target of a transaction on its secondary interface.
0 = Target abort not signaled on the PCI interface
1 = Target abort signaled on the PCI interface
10:9 PCI_SPEED
8
DATAPAR
R
RCU
DEVSEL timing. These bits are 01b indicating that this is a medium-speed decoding device.
Master data parity error. This bit is set if the bridge is the bus master of the transaction on the PCI
bus, bit 0 (PERR_EN) in the bridge control register (offset 3Eh see Section 4.30) is set, and the
bridge either asserts PERR on a read transaction or detects PERR asserted on a write transaction.
0 = No data parity error detected on the PCI interface
1 = Data parity error detected on the PCI interface
7
FBB_CAP
R
Fast back-to-back capable. This bit returns a 1b when read indicating that the secondary PCI
interface of bridge supports fast back-to-back transactions.
6
RSVD
R
Reserved. Returns 0b when read.
5
66MHZ
R
66-MHz capable. The bridge operates at a PCI bus CLK frequency of 66 MHz; therefore, this bit
always returns a 1b.
4:0
RSVD
R
Reserved. Returns 00000b when read.
58
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.19 Memory Base Register
This read/write register specifies the lower limit of the memory addresses that the bridge forwards
downstream. See Table 4-10 for a complete description of the register contents.
PCI register offset:
20h
Register type:
Read only, Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-10. Memory Base Register Description
BIT
FIELD NAME
15:4
MEMBASE
3:0
RSVD
ACCESS
DESCRIPTION
RW
Memory base. Defines the lowest address of the memory address range that determines when to
forward memory transactions from one interface to the other. These bits correspond to address bits
[31:20] in the memory address. The lower 20 bits are assumed to be 00000h.
R
Reserved. Returns 0h when read.
4.20 Memory Limit Register
This read/write register specifies the upper limit of the memory addresses that the bridge forwards
downstream. See Table 4-11 for a complete description of the register contents.
PCI register offset:
22h
Register type:
Read only, Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-11. Memory Limit Register Description
BIT
FIELD NAME
15:4
MEMLIMIT
3:0
RSVD
ACCESS
DESCRIPTION
RW
Memory limit. Defines the highest address of the memory address range that determines when to
forward memory transactions from one interface to the other. These bits correspond to address bits
[31:20] in the memory address. The lower 20 bits are assumed to be FFFFFh.
R
Submit Documentation Feedback
Reserved. Returns 0h when read.
Classic PCI Configuration Space
59
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.21 Prefetchable Memory Base Register
This read/write register specifies the lower limit of the prefetchable memory addresses that the bridge
forwards downstream. See Table 4-12 for a complete description of the register contents.
PCI register offset:
24h
Register type:
Read only, Read/Write
Default value:
0001h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Table 4-12. Prefetchable Memory Base Register Description
BIT
FIELD NAME
15:4
PREBASE
3:0
64BIT
ACCESS
DESCRIPTION
RW
Prefetchable memory base. Defines the lowest address of the prefetchable memory address range
that determines when to forward memory transactions from one interface to the other. These bits
correspond to address bits [31:20] in the memory address. The lower 20 bits are assumed to be
00000h. The prefetchable base upper 32 bits register (offset 28h, see Section 4.23) specifies the bit
[63:32] of the 64-bit prefetchable memory address.
R
64-bit memory indicator. These read-only bits indicate that 64-bit addressing is supported for this
memory window.
4.22 Prefetchable Memory Limit Register
This read/write register specifies the upper limit of the prefetchable memory addresses that the bridge
forwards downstream. See Table 4-13 for a complete description of the register contents.
PCI register offset:
26h
Register type:
Read only, Read/Write
Default value:
BIT NUMBER
RESET STATE
15
0
0001h
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Table 4-13. Prefetchable Memory Limit Register Description
BIT
FIELD NAME
15:4
PRELIMIT
3:0
64BIT
60
ACCESS
DESCRIPTION
RW
Prefetchable memory limit. Defines the highest address of the prefetchable memory address range
that determines when to forward memory transactions from one interface to the other. These bits
correspond to address bits [31:20] in the memory address. The lower 20 bits are assumed to be
FFFFFh. The prefetchable limit upper 32 bits register (offset 2Ch, see Section 4.24) specifies the bit
[63:32] of the 64-bit prefetchable memory address.
R
64-bit memory indicator. These read-only bits indicate that 64-bit addressing is supported for this
memory window.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.23 Prefetchable Base Upper 32 Bits Register
This read/write register specifies the upper 32 bits of the prefetchable memory base register. See
Table 4-14 for a complete description of the register contents.
PCI register offset:
28h
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-14. Prefetchable Base Upper 32 Bits Register Description
BIT
31:0
FIELD NAME
ACCESS
PREBASE
RW
DESCRIPTION
Prefetchable memory base upper 32 bits. Defines the upper 32 bits of the lowest address of the
prefetchable memory address range that determines when to forward memory transactions
downstream.
4.24 Prefetchable Limit Upper 32 Bits Register
This read/write register specifies the upper 32 bits of the prefetchable memory limit register. See
Table 4-15 for a complete description of the register contents.
PCI register offset:
2Ch
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-15. Prefetchable Limit Upper 32 Bits Register Description
BIT
31:0
FIELD NAME
PRELIMIT
ACCESS
RW
Submit Documentation Feedback
DESCRIPTION
Prefetchable memory limit upper 32 bits. Defines the upper 32 bits of the highest address of the
prefetchable memory address range that determines when to forward memory transactions
downstream.
Classic PCI Configuration Space
61
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.25 I/O Base Upper 16 Bits Register
This read/write register specifies the upper 16 bits of the I/O base register. See Table 4-16 for a complete
description of the register contents.
PCI register offset:
30h
Register type:
Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-16. I/O Base Upper 16 Bits Register Description
BIT
15:0
FIELD NAME
ACCESS
IOBASE
RW
DESCRIPTION
I/O base upper 16 bits. Defines the upper 16 bits of the lowest address of the I/O address range
that determines when to forward I/O transactions downstream. These bits correspond to address
bits [31:20] in the I/O address. The lower 20 bits are assumed to be 00000h.
4.26 I/O Limit Upper 16 Bits Register
This read/write register specifies the upper 16 bits of the I/O limit register. See Table 4-17 for a complete
description of the register contents.
PCI register offset:
32h
Register type:
Read/Write
Default value:
BIT NUMBER
RESET STATE
15
0
0000h
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-17. I/O Limit Upper 16 Bits Register Description
BIT
15:0
62
FIELD NAME
IOLIMIT
ACCESS
RW
DESCRIPTION
I/O limit upper 16 bits. Defines the upper 16 bits of the top address of the I/O address range that
determines when to forward I/O transactions downstream. These bits correspond to address bits
[31:20] in the I/O address. The lower 20 bits are assumed to be FFFFFh.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.27 Capabilities Pointer Register
This read-only register provides a pointer into the PCI configuration header where the PCI power
management block resides. Since the PCI power-management registers begin at 50h, this register is
hardwired to 50h.
PCI register offset:
34h
Register type:
Read only
Default value:
50h
BIT NUMBER
RESET STATE
7
0
6
1
5
0
4
1
3
0
2
0
1
0
0
0
4.28 Interrupt Line Register
This read/write register is programmed by the system and indicates to the software which interrupt line the
bridge has assigned to it. The default value of this register is FFh, indicating that an interrupt line has not
yet been assigned to the function. Since the bridge does not generate interrupts internally, this register is
a scratchpad register.
PCI register offset:
3Ch
Register type:
Read/Write
Default value:
FFh
BIT NUMBER
RESET STATE
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
1
4.29 Interrupt Pin Register
The interrupt pin register is read-only 00h indicating that the bridge does not generate internal interrupts.
While the bridge does not generate internal interrupts, it does forward interrupts from the secondary
interface to the primary interface.
PCI register offset:
3Dh
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
Submit Documentation Feedback
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Classic PCI Configuration Space
63
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.30
www.ti.com
Bridge Control Register
The bridge control register provides extensions to the command register that are specific to a bridge. See
Table 4-18 for a complete description of the register contents.
PCI register offset:
3Eh
Register type:
Read only, Read/Write, Read/Clear
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-18. Bridge Control Register Description
BIT
FIELD NAME
15:12
11
RSVD
DTSERR
ACCESS
R
RW
DESCRIPTION
Reserved. Returns 0h when read.
Discard timer SERR enable. Applies only in conventional PCI mode. This bit enables the
bridge to generate either an ERR_NONFATAL (by default) or ERR_FATAL transaction on
the primary interface when the secondary discard timer expires and a delayed transaction
is discarded from a queue in the bridge. The severity is selectable only if advanced error
reporting is supported.
0 = Do not generate ERR_NONFATAL or ERR_FATAL on the primary interface as a
result of the expiration of the secondary discard timer. Note that an error message
can still be sent if advanced error reporting is supported and bit 10
(DISCARD_TIMER_MASK) in the secondary uncorrectable error mask register
(offset 130h, see Section 5.11) is clear (default).
1 = Generate ERR_NONFATAL or ERR_FATAL on the primary interface if the
secondary discard timer expires and a delayed transaction is discarded from a
queue in the bridges.
10
DTSTATUS
RCU
Discard timer status. This bit indicates if a discard timer expires and a delayed transaction
is discarded.
0 = No discard timer error
1 = Discard timer error
9
SEC_DT
RW selects the number of PCI clocks that the bridge waits for the 1394a OHCI master on
the secondary interface to repeat a delayed transaction request. The counter starts once
the delayed completion (the completion of the delayed transaction on the primary
interface) has reached the head of the downstream queue of the bridge (i.e., all ordering
requirements have been satisfied and the bridge is ready to complete the delayed
transaction with the initiating master on the secondary bus). If the master does not repeat
the transaction before the counter expires, the bridge deletes the delayed transaction from
its queue and sets the discard timer status bit.
0 = Secondary discard timer counts 215 PCI clock cycles (default).
1 = Secondary discard timer counts 210 PCI clock cycles.
8
PRI_DEC
R
Primary discard timer. This bit has no meaning in PCIe and is hardwired to 0b.
7
FBB_EN
RW
Fast back-to-back enable. This bit allows software to enable fast back-to-back
transactions on the secondary PCI interface.
0 = Fast back-to-back transactions are disabled (default).
1 = Secondary interface fast back-to-back transactions are enabled.
6
SRST
RW
Secondary bus reset. This bit is set when software wishes to reset all devices
downstream of the bridge. Setting this bit causes the PRST signal on the secondary
interface to be asserted.
0 = Secondary interface is not in reset state (default).
1 = Secondary interface is in the reset state.
64
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 4-18. Bridge Control Register Description (continued)
BIT
5
FIELD NAME
MAM
ACCESS
RW
DESCRIPTION
Master abort mode. This bit controls the behavior of the bridge when it receives a master
abort or an unsupported request.
0 = Do not report master aborts. Returns FFFF FFFFh on reads and discard data on
writes (default).
1 = Respond with an unsupported request on PCIe when a master abort is received on
PCI. Respond with target abort on PCI when an unsupported request completion
on PCIe is received. This bit also enables error signaling on master abort
conditions on posted writes.
4
VGA16
RW
VGA 16-bit decode. This bit enables the bridge to provide full 16-bit decoding for VGA I/O
addresses. This bit only has meaning if the VGA enable bit is set.
0 = Ignore address bits [15:10] when decoding VGA I/O addresses (default)
1 = Decode address bits [15:10] when decoding VGA I/O addresses
3
VGA
RW
VGA enable. This bit modifies the response by the bridge to VGA compatible addresses.
If this bit is set, the bridge decodes and forwards the following accesses on the primary
interface to the secondary interface (and, conversely, block the forwarding of these
addresses from the secondary to primary interface):
Memory accesses in the range 000A 0000h to 000B FFFFh
I/O addresses in the first 64 KB of the I/O address space (address bits [31:16] are
0000h) and where address bits [9:0] are in the range of 3B0h to 3BBh or 3C0h to
3DFh (inclusive of ISA address aliases – address bits [15:10] may possess any
value and are not used in the decoding)
If this bit is set, forwarding of VGA addresses is independent of the value of bit 2 (ISA),
the I/O address and memory address ranges defined by the I/O base and limit registers,
the memory base and limit registers, and the prefetchable memory base and limit
registers of the bridge. The forwarding of VGA addresses is qualified by bits 0 (IO_ENB)
and 1 (MEMORY_ENB) in the command register (offset 04h, see Section 4.3).
0 = Do not forward VGA-compatible memory and I/O addresses from the primary to
secondary interface (addresses previously defined) unless they are enabled for
forwarding by the defined I/O and memory address ranges (default).
1 = Forward VGA-compatible memory and I/O addresses (addresses previously
defined) from the primary interface to the secondary interface (if the I/O enable and
memory enable bits are set) independent of the I/O and memory address ranges
and independent of the ISA enable bit.
2
ISA
RW
ISA enable. This bit modifies the response by the bridge to ISA I/O addresses. This
applies only to I/O addresses that are enabled by the I/O base and I/O limit registers and
are in the first 64 KB of PCI I/O address space (0000 0000h to 0000 FFFFh). If this bit is
set, the bridge blocks any forwarding from primary to secondary of I/O transactions
addressing the last 768 bytes in each 1-KB block. In the opposite direction (secondary to
primary), I/O transactions are forwarded if they address the last 768 bytes in each 1-KB
block.
0 = Forward downstream all I/O addresses in the address range defined by the I/O
base and I/O limit registers (default)
1 = Forward upstream ISA I/O addresses in the address range defined by the I/O base
and I/O limit registers that are in the first 64 KB of PCI I/O address space (top 768
bytes of each 1-KB block)
1
SERR_EN
RW
SERR enable. This bit controls forwarding of system error events from the secondary
interface to the primary interface. The bridge forwards system error events when:
This bit is set.
Bit 8 (SERR_ENB) in the command register (offset 04h, see Section 4.3) is set.
SERR is asserted on the secondary interface.
0 = Disable the forwarding of system error events (default)
1 = Enable the forwarding of system error events
Submit Documentation Feedback
Classic PCI Configuration Space
65
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 4-18. Bridge Control Register Description (continued)
BIT
0
FIELD NAME
ACCESS
DESCRIPTION
RW
Parity error response enable. Controls the bridge's response to data, uncorrectable
address, and attribute errors on the secondary interface. Also, the bridge always forwards
data with poisoning, from conventional PCI to PCIe on an uncorrectable conventional PCI
data error, regardless of the setting of this bit.
PERR_EN
0 = Ignore uncorrectable address, attribute, and data errors on the secondary interface
(default)
1 = Enable uncorrectable address, attribute, and data error detection and reporting on
the secondary interface
4.31 PM Capability ID Register
This read-only register identifies the linked list item as the register for PCI power management. The
register returns 01h when read.
PCI register offset:
50h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
01h
6
0
5
0
4
0
3
0
2
0
1
0
0
1
4.32 Next Item Pointer Register
The contents of this read-only register indicate the next item in the linked list of capabilities for the bridge.
This register reads 80h pointing to the subsystem ID capabilities registers.
PCI register offset:
51h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
66
7
0
60h
6
1
Classic PCI Configuration Space
5
1
4
0
3
0
2
0
1
0
0
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.33 Power Management Capabilities Register
This read-only register indicates the capabilities of the bridge related to PCI power management. See
Table 4-19 for a complete description of the register contents.
PCI register offset:
52h
Register type:
Read only
Default value:
0603h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
1
9
1
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
1
0
1
Table 4-19. Power Management Capabilities Register Description
BIT
FIELD NAME
ACCESS
15:11
PME_SUPPORT
R
PME support. This 5-bit field indicates the power states from which the bridge may assert
PME. Because the bridge never generates a PME except on a behalf of a secondary
device, this field is read only and returns 00000b.
10
D2_SUPPORT
R
This bit returns a 1b when read, indicating that the function supports the D2 device power
state.
9
D1_SUPPORT
R
This bit returns a 1b when read, indicating that the function supports the D1 device power
state.
AUX_CURRENT
R
3.3 VAUX auxiliary current requirements. This field returns 000b since the bridge does not
generate PME from D3cold.
5
DSI
R
Device specific initialization. This bit returns 0b when read, indicating that the bridge does
not require special initialization beyond the standard PCI configuration header before a
generic class driver is able to use it.
4
RSVD
R
Reserved. Returns 0b when read.
3
PME_CLK
R
PME clock. This bit returns 0b indicating that the PCI clock is not needed to generate PME.
PM_VERSION
R
Power-management version. If bit 26 (PCI_PM_VERSION_CTRL) in the general control
register (offset D4h, see Section 4.66) is 0b, this field returns 010b indicating revision 1.1
compatibility. If PCI_PM_VERSION_CTRL is 1b, this field returns 011b indicating revision
1.2 compatibility.
8:6
2:0
Submit Documentation Feedback
DESCRIPTION
Classic PCI Configuration Space
67
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.34 Power Management Control/Status Register
This register determines and changes the current power state of the bridge. No internal reset is generated
when transitioning from the D3hot state to the D0 state. See Table 4-20 for a complete description of the
register contents.
PCI register offset:
54h
Register type:
Read only, Read/Write
Default value:
0008h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
1
2
0
1
0
0
0
Table 4-20. Power Management Control/Status Register Description
BIT
15
FIELD NAME
ACCESS
DESCRIPTION
PME_STAT
R
PME status. This bit is read only and returns 0b when read.
14:13
DATA_SCALE
R
Data scale. This 2-bit field returns 00b when read since the bridge does not use the data
register.
12:9
DATA_SEL
R
Data select. This 4-bit field returns 0h when read since the bridge does not use the data
register.
8
7:4
PME_EN
RW
PME enable. This bit has no function and acts as scratchpad space. The default value for
this bit is 0b.
RSVD
R
Reserved. Returns 0h when read.
3
NO_SOFT_RESET
R
No soft reset. If bit 26 (PCI_PM_VERSION_CTRL) in the general control register (offset
D4h, see Section 4.66) is 0b, this bit returns 0b for compatibility with version 1.1 of the PCI
Power Management Specification. If PCI_PM_VERSION_CTRL is 1b, this bit returns 1b
indicating that no internal reset is generated and the device retains its configuration context
when transitioning from the D3hot state to the D0 state.
2
RSVD
R
Reserved. Returns 0b when read.
1:0
PWR_STATE
RW
Power state. This 2-bit field determines the current power state of the function and sets the
function into a new power state. This field is encoded as follows:
00 = D0 (default)
01 = D1
10 = D2
11 = D3hot
68
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.35 Power Management Bridge Support Extension Register
This read-only register indicates to host software what the state of the secondary bus will be when the
bridge is placed in D3. See Table 4-21 for a complete description of the register contents.
PCI register offset:
56h
Register type:
Read only
Default value:
40h
BIT NUMBER
RESET STATE
7
0
6
1
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-21. PM Bridge Support Extension Register Description
BIT
7
FIELD NAME
ACCESS
DESCRIPTION
R
Bus power/clock control enable. This bit indicates to the host software if the bus secondary
clocks are stopped when the bridge is placed in D3. The state of the BPCC bit is
controlled by bit 11 (BPCC_E) in the general control register (offset D4h, see
Section 4.66).
BPCC
0 = Secondary bus clocks are not stopped in D3.
1 = Secondary bus clocks are stopped in D3.
6
5:0
BSTATE
R
B2/B3 support. This bit is read-only 1b indicating that the bus state in D3 is B2.
RSVD
R
Reserved. Returns 00 0000b when read.
4.36 Power Management Data Register
The read-only register is not applicable to the bridge and returns 00h when read.
PCI register offset:
57h
Register type:
Read only
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.37 MSI Capability ID Register
This read-only register identifies the linked list item as the register for message signaled interrupts
capabilities. The register returns 05h when read.
PCI register offset:
60h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
Submit Documentation Feedback
05h
6
0
5
0
4
0
3
0
2
1
1
0
0
1
Classic PCI Configuration Space
69
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.38 Next Item Pointer Register
The contents of this read-only register indicate the next item in the linked list of capabilities for the bridge.
This register reads 80h pointing to the subsystem ID capabilities registers.
PCI register offset:
61h
Register type:
Read only
Default value:
80h
BIT NUMBER
RESET STATE
7
1
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.39 MSI Message Control Register
This register controls the sending of MSI messages. See Table 4-22 for a complete description of the
register contents.
PCI register offset:
62h
Register type:
Read only, Read/Write
Default value:
0088h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
1
6
0
5
0
4
0
3
1
2
0
1
0
0
0
Table 4-22. MSI Message Control Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
15:8
RSVD
R
Reserved. Returns 00h when read.
7
64CAP
R
64-bit message capability. This bit is read-only 1b indicating that the bridge supports 64-bit
MSI message addressing.
6:4
MM_EN
RW
Multiple message enable. This bit indicates the number of distinct messages that the
bridge is allowed to generate.
000
001
010
011
100
101
110
111
3:1
MM_CAP
R
0
MSI_EN
RW
= 1 message (default)
= 2 messages
= 4 messages
= 8 messages
= 16 messages
= Reserved
= Reserved
= Reserved
Multiple message capabilities. This field indicates the number of distinct messages that the
bridge is capable of generating. This field is read-only 100b, indicating that the bridge can
signal 1 interrupt for each IRQ supported on the serial IRQ stream up to a maximum of 16
unique interrupts.
MSI enable. This bit enables MSI interrupt signaling. MSI signaling must be enabled by
software for the bridge to signal that a serial IRQ has been detected.
0 = MSI signaling is prohibited (default).
1 = MSI signaling is enabled.
NOTE
Enabling MSI messaging in the XIO2213B has no effect.
70
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.40 MSI Message Lower Address Register
This register contains the lower 32 bits of the address that a MSI message writes to when a serial IRQ is
detected. See Table 4-23 for a complete description of the register contents.
PCI register offset:
64h
Register type:
Read only, Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-23. MSI Message Lower Address Register Description
BIT
FIELD NAME
31:2
ADDRESS
1:0
RSVD
ACCESS
DESCRIPTION
RW
System specified message address
R
Reserved. Returns 00b when read.
NOTE
Enabling MSI messaging in the XIO2213B has no effect.
4.41 MSI Message Upper Address Register
This register contains the upper 32 bits of the address that a MSI message writes to when a serial IRQ is
detected. If this register contains 0000 0000h, 32-bit addressing is used; otherwise, 64-bit addressing is
used.
PCI register offset:
68h
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
NOTE
Enabling MSI messaging in the XIO2213B has no effect.
Submit Documentation Feedback
Classic PCI Configuration Space
71
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.42 MSI Message Data Register
This register contains the data that software programmed the bridge to send when it send a MSI message.
See Table 4-24 for a complete description of the register contents.
PCI register offset:
6Ch
Register type:
Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-24. MSI Message Data Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
15:4
MSG
RW
System specific message. This field contains the portion of the message that the bridge
forwards unmodified.
3:0
MSG_NUM
RW
Message number. This portion of the message field may be modified to contain the
message number is multiple messages are enable. The number of bits that are modifiable
depends on the number of messages enabled in the message control register.
1 message = No message data bits can be modified (default).
2 messages = Bit 0 can be modified.
4 messages = Bits 1:0 can be modified.
8 messages = Bits 2:0 can be modified.
16 messages = Bits 3:0 can be modified.
NOTE
Enabling MSI messaging in the XIO2213B has no effect.
4.43
SSID/SSVID Capability ID Register
This read-only register identifies the linked list item as the register for subsystem ID and subsystem
vendor ID capabilities. The register returns 0Dh when read.
PCI register offset:
80h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
0Dh
6
0
5
0
4
0
3
1
2
1
1
0
0
1
4.44 Next Item Pointer Register
The contents of this read-only register indicate the next item in the linked list of capabilities for the bridge.
This register reads 90h pointing to the PCI Express capabilities registers.
PCI register offset:
81h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
72
7
1
90h
6
0
Classic PCI Configuration Space
5
0
4
1
3
0
2
0
1
0
0
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.45 Subsystem Vendor ID Register
This register, used for system and option card identification purposes, may be required for certain
operating systems. This read-only register is initialized through the EEPROM and can be written through
the subsystem alias register. This register shall only be reset by a fundamental reset (FRST).
PCI register offset:
84h
Register type:
Read only
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.46 Subsystem ID Register
This register, used for system and option card identification purposes, may be required for certain
operating systems. This read-only register is initialized through the EEPROM and can be written through
the subsystem alias register. This register shall only be reset by FRST.
PCI register offset:
86h
Register type:
Read only
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.47 PCI Express Capability ID Register
This read-only register identifies the linked list item as the register for PCIe capabilities. The register
returns 10h when read.
PCI register offset:
90h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
10h
6
0
5
0
4
1
3
0
2
0
1
0
0
0
4.48 Next Item Pointer Register
The contents of this read-only register indicate the next item in the linked list of capabilities for the bridge.
This register reads 00h indicating no additional capabilities are supported.
PCI register offset:
91h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
Submit Documentation Feedback
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Classic PCI Configuration Space
73
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.49 PCI Express Capabilities Register
This read-only register indicates the capabilities of the bridge related to PCIe. See Table 4-25 for a
complete description of the register contents.
PCI register offset:
92h
Register type:
Read only
Default value:
0071h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
1
5
1
4
1
3
0
2
0
1
0
0
1
Table 4-25. PCI Express Capabilities Register Description
BIT
74
FIELD NAME
ACCESS
DESCRIPTION
15:9
RSVD
R
Reserved. Returns 000 0000b when read.
8
SLOT
R
Slot implemented. This bit is not valid for the bridge and is read-only 0b.
7:4
DEV_TYPE
R
Device/port type. This read-only field returns 0111b indicating that the device is a PCIe to
PCI bridge.
3:0
VERSION
R
Capability version. This field returns 1h indicating revision 1 of the PCIe capability.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.50 Device Capabilities Register
This register indicates the device-specific capabilities of the bridge. See Table 4-26 for a complete
description of the register contents.
PCI register offset:
94h
Register type:
Read only
Default value:
0000 8002
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
1
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
Table 4-26. Device Capabilities Register Description
BIT
FIELD NAME
ACCESS
31:28
RSVD
R
27:26
CSPLS
RU
DESCRIPTION
Reserved. Returns 0h when read.
Captured slot power limit scale. The value in this field is programmed by the host by issuing a
Set_Slot_Power_Limit message. When a Set_Slot_Power_Limit message is received, bits 9:8
are written to this field. The value in this field specifies the scale used for the slot power limit.
00 =
01 =
10 =
11 =
1.0x
0.1x
0.01x
0.001x1
25:18
CSPLV
RU
Captured slot power limit value. The value in this field is programmed by the host by issuing a
Set_Slot_Power_Limit message. When a Set_Slot_Power_Limit message is received, bits 7:0
are written to this field. The value in this field in combination with the slot power limit scale value
(bits 27:26) specifies the upper limit of power supplied to the slot. The power limit is calculated
by multiplying the value in this field by the value in the slot power limit scale field.
17:16
RSVD
R
Reserved. Return 000b when read.
15
RBER
R
Role-based error reporting. This bit is hardwired to 1 indicating that the XIO2213B supports
role-based error reporting.
14
PIP
R
Power indicator present. This bit is hardwired to 0b indicating that a power indicator is not
implemented.
13
AIP
R
Attention indicator present. This bit is hardwired to 0b indicating that an attention indicator is not
implemented.
12
ABP
R
Attention button present. This bit is hardwired to 0b indicating that an attention button is not
implemented.
11:9
EP_L1_LAT
RU
Endpoint L1 acceptable latency. This field indicates the maximum acceptable latency for a
transition from L1 to L0 state. This field can be programmed by writing to the L1_LATENCY
field (bits 15:13) in the general control register (offset D4h, see Section 4.66). The default value
for this field is 000b, which indicates a range less than 1s. This field cannot be programmed to
be less than the latency for the PHY to exit the L1 state.
8:6
EP_L0S_LAT
RU
Endpoint L0s acceptable latency. This field indicates the maximum acceptable latency for a
transition from L0s to L0 state. This field can be programmed by writing to the L0s_LATENCY
field (bits 18:16) in the general control register (offset D4h, see Section 4.66). The default value
for this field is 000b, which indicates a range less than 1s. This field cannot be programmed to
be less than the latency for the PHY to exit the L0s state.
ETFS
R
Extended tag field supported. This field indicates the size of the tag field not supported.
4:3
5
PFS
R
Phantom functions supported. This field is read-only 00b indicating that function numbers are
not used for phantom functions.
2:0
MPSS
R
Maximum payload size supported. This field indicates the maximum payload size that the
device can support for TLPs. This field is encoded as 010b indicating the maximum payload
size for a TLP is 512 bytes.
Submit Documentation Feedback
Classic PCI Configuration Space
75
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.51 Device Control Register
The device control register controls PCIe device-specific meters. See Table 4-27 for a complete
description of the register contents.
PCI register offset:
98h
Register type:
Read only, Read/Write
Default value:
2800h
BIT NUMBER
RESET STATE
15
0
14
0
13
1
12
0
11
1
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-27. Device Control Register Description
BIT
FIELD NAME
15
14:12
ACCESS
DESCRIPTION
CFG_RTRY_ENB
RW
Configuration retry status enable. When this read/write bit is set to 1b, the bridge returns a
completion with completion retry status on PCIe if a configuration transaction forwarded to the
secondary interface did not complete within the implementation specific time-out period. When
this bit is set to 0b, the bridge does not generate completions with completion retry status on
behalf of configuration transactions. The default value of this bit is 0b.
MRRS
RW
Maximum read request size. This field is programmed by host software to set the maximum
size of a read request that the bridge can generate. The bridge uses this field in conjunction
with the cache line size register (offset 0Ch, see Section 7.6) to determine how much data to
fetch on a read request. This field is encoded as:
000
001
010
011
100
101
110
111
11
ENS
RW
= 128B
= 256B
= 512B (default)
= 1024B
= 2048B
= 4096B
= Reserved
= Reserved
Enable no snoop. Controls the setting of the no snoop flag within the TLP header for upstream
memory transactions mapped to any traffic class mapped to a virtual channel (VC) other than
VC0 through the upstream decode windows.
0 = No snoop field is 0b.
1 = No snoop field is 1b (default).
10*
APPE
RW
Auxiliary power PM enable. This bit has no effect in the bridge.
0 = AUX power is disabled (default).
1 = AUX power is enabled.
9
PFE
R
Phantom function enable. Since the bridge does not support phantom functions, this bit is
read-only 0b.
8
ETFE
R
Extended tag field enable. Since the bridge does not support extended tags, this bit is
read-only 0b.
7:5
MPS
RW
Maximum payload size. This field is programmed by host software to set the maximum size of
posted writes or read completions that the bridge can initiate. This field is encoded as:
000
001
010
011
100
101
110
111
4
ERO
3
URRE
R
RW
= 128B (default)
= 256B
= 512B
= 1024B
= 2048B
= 4096B
= Reserved
= Reserved
Enable relaxed ordering. Since the bridge does not support relaxed ordering, this bit is
read-only 0b.
Unsupported request reporting enable. If this bit is set, the bridge sends an ERR_NONFATAL
message to the root complex when an unsupported request is received.
0 = Do not report unsupported requests to the root complex (default)
1 = Report unsupported requests to the root complex
76
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 4-27. Device Control Register Description (continued)
BIT
2
FIELD NAME
ACCESS
FERE
RW
DESCRIPTION
Fatal error reporting enable. If this bit is set, the bridge is enabled to send ERR_FATAL
messages to the root complex when a system error event occurs.
0 = Do not report fatal errors to the root complex (default)
1 = Report fatal errors to the root complex
1
NFERE
RW
Nonfatal error reporting enable. If this bit is set, the bridge is enabled to send
ERR_NONFATAL messages to the root complex when a system error event occurs.
0 = Do not report nonfatal errors to the root complex (default)
1 = Report nonfatal errors to the root complex
0
CERE
RW
Correctable error reporting enable. If this bit is set, the bridge is enabled to send ERR_COR
messages to the root complex when a system error event occurs.
0 = Do not report correctable errors to the root complex (default)
1 = Report correctable errors to the root complex
4.52 Device Status Register
The device status register provides PCIe device specific information to the system. See Table 4-28 for a
complete description of the register contents.
PCI register offset:
9Ah
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
15
0
0000h
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-28. Device Status Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
15:6
RSVD
R
Reserved. Returns 00 0000 0000b when read.
5
PEND
RU
Transaction pending. This bit is set when the bridge has issued a nonposted transaction that has
not been completed.
4
APD
RU
AUX power detected. This bit indicates that AUX power is present.
0 = No AUX power detected
1 = AUX power detected
3
URD
RCU
Unsupported request detected. This bit is set by the bridge when an unsupported request is
received.
2
FED
RCU
Fatal error detected. This bit is set by the bridge when a fatal error is detected.
1
NFED
RCU
Nonfatal error detected. This bit is set by the bridge when a nonfatal error is detected.
0
CED
RCU
Correctable error detected. This bit is set by the bridge when a correctable error is detected.
Submit Documentation Feedback
Classic PCI Configuration Space
77
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.53 Link Capabilities Register
The link capabilities register indicates the link-specific capabilities of the bridge. See Table 4-29 for a
complete description of the register contents.
PCI register offset:
9Ch
Register type:
Read only
Default value:
0006 XC11h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
1
17
1
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
x
x
x
1
1
0
0
0
0
0
1
0
0
0
1
Table 4-29. Link Capabilities Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
31:24
PORT_NUM
R
Port number. This field indicates port number for the PCIe link. This field is read-only 00h
indicating that the link is associated with port 0.
23:19
RSVD
R
Reserved. Return 00 0000b when read.
CLK_PM
R
Clock power management. This bit is hardwired to 1 to indicate that XIO2213B supports clock
power management through CLKREQ protocol.
L1_LATENCY
R
L1 exit latency. This field indicates the time that it takes to transition from the L1 state to the L0
state. Bit 6 (CCC) in the link control register (offset A0h, see Section 4.54) equals 1b for a
common clock and equals 0b for an asynchronous clock.
18
17:15
For a common reference clock, the value of this field is determined by bits 20:18
(L1_EXIT_LAT_ASYNC) of the control and diagnostic register 1 (offset C4h, see Section 4.63).
For an asynchronous reference clock, the value of this field is determined by bits 17:15
(L1_EXIT_LAT_COMMON) of the control and diagnostic register 1 (offset C4h, see
Section 4.63).
14:12
L0S_LATENCY
R
L0s exit latency. This field indicates the time that it takes to transition from the L0s state to the
L0 state. Bit 6 (CCC) in the link control register (offset A0h, see Section 4.54) equals 1b for a
common clock and equals 0b for an asynchronous clock.
For a common reference clock, the value of 011b indicates that the L1 exit latency falls between
256 ns to less than 512 ns.
For an asynchronous reference clock, the value of 100b indicates that the L1 exit latency falls
between 512 ns to less than 1 s.
11:10
78
ASLPMS
R
Active-state link PM support. This field indicates the level of active-state power management
that the bridge supports. The value 11b indicates support for both L0s and L1 through
active-state power management.
9:4
MLW
R
Maximum link width. This field is encoded 00 0001b to indicate that the bridge only supports a
1× PCIe link.
3:0
MLS
R
Maximum link speed. This field is encoded 1h to indicate that the bridge supports a maximum
link speed of 2.5 Gb/s.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.54 Link Control Register
The link control register controls link-specific behavior. See Table 4-30 for a complete description of the
register contents.
PCI register offset:
A0h
Register type:
Read only, Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-30. Link Control Register Description
BIT
15:9
8
FIELD NAME
ACCESS
DESCRIPTION
RSVD
RW
Reserved. Returns 00h when read.
CPM_EN
RW
Clock power management enable. This bit is used to enable XIO2213B to use CLKREQ
for clock power management
0 = Clock power management is disabled and XIO2213B shall hold the CLKREQ
signal low.
1 = Clock power management is enabled and XIO2213B is permitted to use the
CLKREQ signal to allow the REFCLK input to be stopped.
7
ES
RW
Extended synch. This bit forces the bridge to extend the transmission of FTS ordered sets
and an extra TS2 when exiting from L1 prior to entering to L0.
0 = Normal synch (default)
1 = Extended synch
6
CCC
RW
Common clock configuration. When this bit is set, it indicates that the bridge and the
device at the opposite end of the link are operating with a common clock source. A value
of 0b indicates that the bridge and the device at the opposite end of the link are operating
with se te reference clock sources. The bridge uses this common clock configuration
information to report the correct L0s and L1 exit latencies.
0 = Reference clock is asynchronous (default).
1 = Reference clock is common.
5
RL
4
LD
3
RCB
R
Retrain link. This bit has no function and is read-only 0b.
R
Link disable. This bit has no function and is read-only 0b.
RW
Read completion boundary. This bit is an indication of the RCB of the root complex. The
state of this bit has no effect on the bridge, since the RCB of the bridge is fixed at 128
bytes.
0 = 64 bytes (default)
1 = 128 bytes
2
1:0
RSVD
ASLPMC
R
RW
Reserved. Returns 0b when read.
Active-state link PM control. This field enables and disables the active-state PM.
00
01
10
11
Submit Documentation Feedback
=
=
=
=
Active-state PM disabled (default)
L0s entry enabled
L1 entry enabled
L0s and L1 entry enabled
Classic PCI Configuration Space
79
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.55 Link Status Register
The link status register indicates the current state of the PCIe link. See Table 4-31 for a complete
description of the register contents.
PCI register offset:
A2h
Register type:
Read only
Default value:
X011h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
x
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
1
3
0
2
0
1
0
0
1
Table 4-31. Link Status Register Description
BIT
15:13
12
FIELD NAME
ACCESS
DESCRIPTION
RSVD
R
Reserved. Returns 000b when read.
SCC
R
Slot clock configuration. This bit indicates that the bridge uses the same physical reference
clock that the platform provides on the connector. If the bridge uses an independent clock
irrespective of the presence of a reference on the connector, this bit must be cleared.
0 = Independent 125-MHz reference clock is used.
1 = Common 100-MHz reference clock is used.
11
LT
R
Link training. This bit has no function and is read-only 0b.
10
TE
R
Retrain link. This bit has no function and is read-only 0b.
9:4
NLW
R
Negotiated link width. This field is read-only 00 0001b indicating the lane width is 1×.
3:0
LS
R
Link speed. This field is read-only 1h indicating the link speed is 2.5 Gb/s.
4.56 Serial-Bus Data Register
The serial-bus data register reads and writes data on the serial-bus interface. Write data is loaded into this
register prior to writing the serial-bus slave address register (offset B2h, see Section 4.58) that initiates the
bus cycle. When reading data from the serial bus, this register contains the data read after bit 5
(REQBUSY) of the serial-bus control and status register (offset B3h, see Section 4.59) is cleared. This
register shall only be reset by FRST.
PCI register offset:
B0h
Register type:
Read/Write
Default value:
BIT NUMBER
RESET STATE
7
0
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.57 Serial-Bus Word Address Register
The value written to the serial-bus word address register represents the word address of the byte being
read from or written to the serial-bus device. The word address is loaded into this register prior to writing
the serial-bus slave address register (offset B2h, see Section 4.58) that initiates the bus cycle. This
register shall only be reset by FRST.
PCI register offset:
B1h
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
80
7
0
6
0
Classic PCI Configuration Space
5
0
4
0
3
0
2
0
1
0
0
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.58 Serial-Bus Slave Address Register
The serial-bus slave address register indicates the slave address of the device being targeted by the
serial-bus cycle. This register also indicates if the cycle is a read or a write cycle. Writing to this register
initiates the cycle on the serial interface. See Table 4-32 for a complete description of the register
contents.
PCI register offset:
B2h
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-32. Serial-Bus Slave Address Register Descriptions
BIT
7:1
(1)
0 (1)
FIELD NAME
ACCESS
DESCRIPTION
SLAVE_ADDR
RW
Serial-bus slave address. This 7-bit field is the slave address for a serial-bus read or write
transaction. The default value for this field is 000 0000b.
RW_CMD
RW
Read/write command. This bit determines if the serial-bus cycle is a read or a write cycle.
0 = A single byte write is requested (default).
1 = A single byte read is requested.
(1)
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
Classic PCI Configuration Space
81
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.59 Serial-Bus Control and Status Register
The serial-bus control and status register controls the behavior of the serial-bus interface. This register
also provides status information about the state of the serial bus. See Table 4-33 for a complete
description of the register contents.
PCI register offset:
B3h
Register type:
Read only, Read/Write, Read/Clear
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-33. Serial-Bus Control and Status Register Description
BIT
7
(1)
FIELD NAME
PROT_SEL
ACCESS
RW
DESCRIPTION
Protocol select. This bit selects the serial-bus address mode used.
0 = Slave address and word address are sent on the serial bus (default
1 = Only the slave address is sent on the serial bus.
6
5(1)
RSVD
REQBUSY
R
RU
Reserved. Returns 0b when read.
Requested serial-bus access busy. This bit is set when a software-initiated serial-bus cycle
is in progress.
0 = No serial-bus cycle
1 = Serial-bus cycle in progress
4(1)
ROMBUSY
RU
Serial EEPROM access busy. This bit is set when the serial EEPROM circuitry in the bridge
is downloading register defaults from a serial EEPROM.
0 = No EEPROM activity
1 = EEPROM download in progress
3(1)
SBDETECT
RWU
Serial EEPROM access busy. This bit is set when the serial EEPROM circuitry in the bridge
is downloading register defaults from a serial EEPROM.
Note: A serial EEPROM is only detected once following PERST.
0 = No EEPROM present, EEPROM load process does not happen. GPIO4//SCL and
GPIO5//SDA terminals are configured as GPIO signals.
1 = EEPROM present, EEPROM load process takes place. GPIO4//SCL and
GPIO5//SDA terminals are configured as serial-bus signals.
2(1)
SBTEST
RW
Serial-bus test. This bit is used for internal test purposes. This bit controls the clock source
for the serial interface clock.
0 = Serial-bus clock at normal operating frequency ~60 kHz (default)
1 = Serial-bus clock frequency increased for test purposes ~4 MHz
1(1)
SB_ERR
RCU
Serial-bus error. This bit is set when an error occurs during a software-initiated serial-bus
cycle.
0 = No error
1 = Serial-bus error
0(1)
ROM_ERR
RCU
Serial EEPROM load error. This bit is set when an error occurs while downloading registers
from serial EEPROM.
0 = No error
1 = EEPROM load error
(1)
82
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.60 GPIO Control Register
This register controls the direction of the eight GPIO terminals. This register has no effect on the behavior
of GPIO terminals that are enabled to perform secondary functions. The secondary functions share GPIO4
(SCL) and GPIO5 (SDA). See Table 4-34 for a complete description of the register contents.
PCI register offset:
B4h
Register type:
Read only, Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-34. GPIO Control Register Description
BIT
FIELD NAME
15:8
RSVD
7 (1)
GPIO7_DIR
ACCESS
R
RW
DESCRIPTION
Reserved. Return 00h when read.
GPIO 7 data direction. This bit selects whether GPIO7 is in input or output mode.
0 = Input (default)
1 = Output
6(1)
GPIO6_DIR
RW
GPIO 6 data direction. This bit selects whether GPIO6 is in input or output mode.
0 = Input (default)
1 = Output
5(1)
GPIO5_DIR
RW
GPIO 5 data direction. This bit selects whether GPIO5 is in input or output mode.
0 = Input (default)
1 = Output
4(1)
GPIO4_DIR
RW
GPIO 4 data direction. This bit selects whether GPIO4 is in input or output mode.
0 = Input (default)
1 = Output
3(1)
GPIO3_DIR
RW
GPIO 3 data direction. This bit selects whether GPIO3 is in input or output mode.
0 = Input (default)
1 = Output
2(1)
GPIO2_DIR
RW
GPIO 2 data direction. This bit selects whether GPIO2 is in input or output mode.
0 = Input (default)
1 = Output
1(1)
GPIO1_DIR
RW
GPIO 1 data direction. This bit selects whether GPIO1 is in input or output mode.
0 = Input (default)
1 = Output
0(1)
GPIO0_DIR
RW
GPIO 0 data direction. This bit selects whether GPIO0 is in input or output mode.
0 = Input (default)
1 = Output
(1)
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
Classic PCI Configuration Space
83
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.61 GPIO Data Register
This register reads the state of the input-mode GPIO terminals and changes the state of the output-mode
GPIO terminals. Writing to a bit that is in input mode or is enabled for a secondary function is ignored. The
secondary functions share GPIO4 (SCL) and GPIO5 (SDA). The default value at power up depends on
the state of the GPIO terminals as they default to general-purpose inputs. See Table 4-35 for a complete
description of the register contents.
PCI register offset:
B6h
Register type:
Read only, Read/Write
Default value:
00XXh
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
x
6
x
5
x
4
x
3
x
2
x
1
x
0
x
Table 4-35. GPIO Data Register Description
BIT
(1)
84
FIELD NAME
ACCESS
R
DESCRIPTION
15:8
RSVD
7 (1)
GPIO7_DATA
RW
Reserved
GPIO 7 data. This bit reads the state of GPIO7 when in input mode or changes the state of
GPIO7 when in output mode.
6(1)
GPIO6_DATA
RW
GPIO 6 data. This bit reads the state of GPIO6 when in input mode or changes the state of
GPIO6 when in output mode.
5(1)
GPIO5_DATA
RW
GPIO 5 data. This bit reads the state of GPIO5 when in input mode or changes the state of
GPIO5 when in output mode.
4(1)
GPIO4_DATA
RW
GPIO 4 data. This bit reads the state of GPIO4 when in input mode or changes the state of
GPIO4 when in output mode.
3(1)
GPIO3_DATA
RW
GPIO 3 data. This bit reads the state of GPIO3 when in input mode or changes the state of
GPIO3 when in output mode.
2(1)
GPIO2_DATA
RW
GPIO 2 data. This bit reads the state of GPIO2 when in input mode or changes the state of
GPIO2 when in output mode.
1(1)
GPIO1_DATA
RW
GPIO 1 data. This bit reads the state of GPIO1 when in input mode or changes the state of
GPIO1 when in output mode.
0(1)
GPIO0_DATA
RW
GPIO 0 data. This bit reads the state of GPIO0 when in input mode or changes the state of
GPIO0 when in output mode.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.62 Control and Diagnostic Register 0
The contents of this register are used for monitoring status and controlling behavior of the bridge. See
Table 4-36 for a complete description of the register contents. It is recommended that all values within this
register be left at the default value. Improperly programming fields in this register may cause
interoperability or other problems.
PCI register offset:
C0h
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-36. Control and Diagnostic Register 0 Description
BIT
FIELD NAME
(1)
31:24
ACCESS
DESCRIPTION
PRI_BUS_NUM
R
This field contains the captured primary bus number.
23:19(1)
PRI_DEVICE_NUM
R
This field contains the captured primary device number.
18
ALT_ERROR_REP
RW
Alternate error reporting. This bit controls the method that the XIO2213B uses for error
reporting.
0 = Advisory nonratal error reporting supported (default)
1 = Advisory nonfatal error reporting not supported
17 (2)
DIS_BRIDGE_PME
RW
Disable bridge PME input
0 = PME input signal to the bridge is enabled and connected to the PME signal
from the 1394 OHCI function (default).
1 = PME input signal to the bridge is disabled.
16 (2)
DIS_OHCI_PME
RW
Disable OHCI_PME
0 = OHCI_PME pin is enabled and connected to the PME signal from the 1394
OHCI function (default).
1 = OHCI_PME pin is disabled.
(1)
15:14
13:12
FIFO_SIZE
RSVD
RW
R
FIFO size. This field contains the maximum size (in DW) of the FIFO.
Reserved. Returns 00b when read.
11
ALLOW_CFG_ANY_FN
RW
Allow configuration access to any function. When this bit is set, the bridge shall respond
to configuration accesses to any function number.
10
RETURN_PW_CREDITS
RW
Return PW packet credits. When this bit is set, the bridge shall return all the PW packet
credits.
9
RSVD
8
RETURN_CPL_CREDITS
RW
Return completion credits. When this bit is set, the bridge shall return all completion
credits immediately.
7
EN_CACHE_LINE_CHECK
RW
Enable cache line check
R
Reserved. Returns 0b when read.
0 = Bridge shall use side-band signals to determine the transaction size (default).
1 = Bridge shall use the cache line size register to determine the transaction size.
(1)
(2)
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
These bits are reset only by a global reset (GRST) or the internally generated power-on reset.
Submit Documentation Feedback
Classic PCI Configuration Space
85
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 4-36. Control and Diagnostic Register 0 Description (continued)
BIT
6(1)
FIELD NAME
PREFETCH_4X
ACCESS
RW
DESCRIPTION
Prefetch 4× enable
0 = Bridge prefetches up to two cache lines, as defined in the cache line size
register (offset 0Ch, see Section 7.6) for upstream memory read multiple
(MRM) transactions (default).
1 = Bridge prefetches up to four cache lines, as defined in the cache line size
register (offset 0Ch, see Section 7.6) for upstream memory read multiple
(MRM) transactions.
Note: When this bit is set and the FORCE_MRM bit in the general control register is
set, both upstream memory read multiple transactions and upstream memory
transactions prefetch up to four cache lines.
Note: When the READ_PREFETCH_DIS bit in the general control register is set, this bit
has no effect and only one DWORD will be fetched on a burst read.
This bit only affects the XIO2213B design when the EN_CACHE_LINE_CHECK bit is
set.
5:4(1)
UP_REQ_BUF_VALUE
RW
PCI upstream req-res buffer threshold value. The value in this field controls the buffer
space that must be available for the device to accept a PCI bus transaction. If the
cache line size is not valid, the device will use eight DW for calculating the threshold
value.
00
01
10
11
3(1)
UP_REQ_BUF_CTRL
RW
=
=
=
=
1
1
1
2
cache
cache
cache
cache
line + 4 DW (default)
line + 8 DW
line + 12 DW
lines + 4 DW
PCI upstream req-res buffer threshold control. This bit enables the PCI upstream
req-res buffer threshold control mode of the bridge.
0 = PCI upstream req-res buffer threshold control mode disabled (default)
1 = PCI upstream req-res buffer threshold control mode enabled
86
2(1)
CFG_ACCESS_MEM_
REG
RW
Configuration access to memory-mapped registers. When this bit is set, the bridge
allows configuration access to memory-mapped configuration registers.
1(1)
RSVD
RW
Reserved. Bit 1 defaults to 0b. If this register is programmed via EEPROM or another
mechanism, the value written into this field must be 0b.
0
RSVD
R
Classic PCI Configuration Space
Reserved. Returns 0b when read.
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.63 Control and Diagnostic Register 1
The contents of this register are used for monitoring status and controlling behavior of the bridge. See
Table 4-37 for a complete description of the register contents. It is recommended that all values within this
register be left at the default value. Improperly programming fields in this register may cause
interoperability or other problems.
PCI register offset:
C4h
Register type:
Read/Write
Default value:
0012 0108h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
1
19
0
18
0
17
1
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
1
0
0
0
0
1
0
0
0
Table 4-37. Control and Diagnostic Register 1 Description
BIT
32:21
FIELD NAME
RSVD
ACCESS
R
DESCRIPTION
Reserved. Returns 000h when read.
20:18 (1)
L1_EXIT_LAT_
ASYNC
RW
L1 exit latency for asynchronous clock. When bit 6 (CCC) of the link control register (offset
A0h, see Section 4.54) is set, the value in this field is mirrored in bits 17:15 (L1_LATENCY)
field in the link capabilities register (offset 9Ch, see Section 4.53). This field defaults to 100b.
17:15(1)
L1_EXIT_LAT_
COMMON
RW
L1 exit latency for common clock. When bit 6 (CCC) of the link control register (offset A0h, see
Section 4.54) is clear, the value in this field is mirrored in bits 17:15 (L1_LATENCY) field in the
link capabilities register (offset 9Ch, see Section 4.53). This field defaults to 100b.
14:11(1)
RSVD
RW
Reserved. Bits 14:11 default to 0000b. If this register is programmed via EEPROM or another
mechanism, the value written into this field must be 0000b.
10(1)
SBUS_RESET_
MASK
RW
Secondary bus reset bit mask. When this bit is set, the bridge masks the reset caused by bit 6
(SRST) of the bridge control register (offset 3Eh, see Section 4.30). This bit defaults to 0b.
9:6(1)
L1ASPM_TIMER
RW
L1ASPM entry timer. This field specifies the value (in 512-ns ticks) of the L1ASPM entry timer.
This field defaults to 0100b.
5:2(1)
L0s_TIMER
RW
L0s entry timer. This field specifies the value (in 62.5-MHz clock ticks) of the L0s entry timer.
This field defaults to 0010b.
1:0(1)
RSVD
RW
Reserved. Bits 1:0 default to 00b. If this register is programmed via EEPROM or another
mechanism, the value written into this field must be 00b.
(1)
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
Classic PCI Configuration Space
87
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.64 PHY Control and Diagnostic Register 2
The contents of this register are used for monitoring status and controlling behavior of the PHY macro for
diagnostic purposes. See Table 4-38 for a complete description of the register contents. It is
recommended that all values within this register be left at the default value. Improperly programming fields
in this register may cause interoperability or other problems.
PCI register offset:
C8h
Register type:
Read/Write
Default value:
3214 2000h
BIT NUMBER
RESET STATE
31
0
30
0
29
1
28
1
27
0
26
0
25
1
24
0
23
0
22
0
21
0
20
1
19
0
18
1
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-38. Control and Diagnostic Register 2 Description
BIT
31:24
FIELD NAME
(1)
23:16(1)
15:13
(1)
12:8
7
6
ACCESS
DESCRIPTION
N_FTS_ ASYNC_
CLK
RW
N_FTS for asynchronous clock. When bit 6 (CCC) of the link control register (offset A0h,
see Section 4.54) is clear, the value in this field is the number of FTS that are sent on a
transition from L0s to L0. This field shall default to 32h.
N_FTS_COMMON_
CLK
RW
N_FTS for common clock. When bit 6 (CCC) of the link control register (offset A0h, see
Section 4.54) is set, the value in this field is the number of FTS that are sent on a transition
from L0s to L0. This field defaults to 14h.
PHY_REV
R
PHY revision number
LINK_NUM
RW
Link number
EN_L2_PWR_
SAVE
RW
Enable L2 power savings
BAR1_EN
RW
0 = Power savings not enabled when in L2
1 = Power savings enabled when in L2
BAR 1 enable
0 = BAR at offset 14h is disabled (default).
1 = BAR at offset 14h is enabled.
5
BAR0_EN
RW
BAR 0 enable
0 = BAR at offset 10h is disabled (default).
1 = BAR at offset 10h is enabled.
(1)
88
4
REQ_RECOVERY
RW
REQ_RECOVERY to LTSSM
3
REQ_RECONFIG
RW
REQ_RECONFIGURE to LTSSM
2
REQ_HOT_RESET
RW
REQ_HOT_RESET to LTSSM
1
REQ_DIS_
SCRAMBLER
RW
REQ_DISABLE_SCRAMBLER to LTSSM
0
REQ_LOOPBACK
RW
REQ_LOOPBACK to LTSSM
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.65 Subsystem Access Register
The contents of this read/write register are aliased to the subsystem vendor ID and subsystem ID registers
at PCI offsets 84h and 86h. See Table 4-39 for a complete description of the register contents.
PCI register offset:
D0h
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 4-39. Subsystem Access Register Description
BIT
31:16
FIELD NAME
(1)
15:0(1)
(1)
ACCESS
DESCRIPTION
SubsystemID
RW
Subsystem ID. The value written to this field is aliased to the subsystem ID register at PCI
offset 86h (see Section 4.46).
SubsystemVendorID
RW
Subsystem vendor ID. The value written to this field is aliased to the subsystem vendor ID
register at PCI offset 84h (see Section 4.45).
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
4.66 General Control Register
This read/write register controls various functions of the bridge. See Table 4-40 for a complete description
of the register contents.
PCI register offset:
D4h
Register type:
Read only, Read/Write
Default value:
8600 025Fh
BIT NUMBER
RESET STATE
31
1
30
0
29
0
28
0
27
0
26
1
25
1
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
1
0
0
1
0
1
1
1
1
1
Submit Documentation Feedback
Classic PCI Configuration Space
89
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 4-40. General Control Register Description
BIT
FIELD NAME
31:30 (1)
CFG_RETRY_
CNTR
ACCESS
RW
DESCRIPTION
Configuration retry counter. Configures the amount of time that a configuration request must be
retried on the secondary PCI bus before it may be completed with configuration retry status on
the PCIe side.
00 =
01 =
10 =
11 =
29:28 (1)
ASPM_CTRL_
DEF_OVRD
RW
25 s
1 ms
25 ms (default)
50 ms
Active-state power-management control default override. These bits are used to determine the
power up default for bits 1:0 of the link control register in the PCIe capability structure.
00 =
01 =
10 =
11 =
Power-on default indicates
(default).
Power-on default indicates
L0s (01b).
Power-on default indicates
L1s (10b).
Power-on default indicates
L0s and L1s (11b).
that the active-state power management is disabled (00b)
that the active-state power management is enabled for
that the active-state power management is enabled for
that the active-state power management is enabled for
27 (2)
LOW_POWER _
EN
RW
Low-power enable. When this bit is set, the half-ampitude, no preemphasis mode for the PCIe TX
drivers is enabled. The default for this bit is 0b.
26 (1)
PCI_PM_
VERSION_ CTRL
RW
PCI power management version control. This bit controls the value reported in bits 2:0
(PM_VERSION) in the power management capabilities register (offset 52h, see Section 4.33). It
also controls the value of bit 3 (NO_SOFT_RESET) in the power management control/status
register (offset 54h, see Section 4.34).
0 = Version fields reports 010b and NO_SOFT_RESET reports 0b for Power
Management 1.1 compliance.
1 = Version fields reports 011b and NO_SOFT_RESET reports 1b for Power
Management 1.2 compliance (default).
25 (1)
STRICT_
PRIORITY_EN
RW
Strict priority enable. When this bit is 0, the default LOW_PRIORITY_COUNT will be 001. When
this bit is 1, the default LOW_PRIORITY_COUNT will be 000. This default value for this bit is 1.
When this bit is set and the LOW_PRIORITY_COUNT is 000, meaning that strict priority VC
arbitration is used and the extended virtual channel always receives priority over VC0 at the PCIe
port.
0 = Default LOW_PRIORITY_COUNT is 001b.
1 = Default LOW_PRIORITY_COUNT is 000b (default).
24 (1)
FORCE_MRM
RW
Force memory read multiple
0 = Memory read multiple transactions are disabled (default).
1 = All upstream memory read transactions initiated on the PCI bus are treated as though
they are memory read multiple transactions in which prefetching is supported for the
transaction. This bit shall only affect the XIO2213B design when the
EN_CACHE_LINE_CHECK bit in the TL control and diagnostic register is set.
23 (1)
CPM_EN_
DEF_OVRD
RW
Clock power-management enable default override. This bit is used to determine the power up
default for bit 8 of the link control register in the PCIe capability structure.
0 = Power-on default indicates that clock power management is disabled (00b) (default).
1 = Power-on default indicates that clock power management is enabled for L0s and L1
(11b).
22:20 (1)
POWER_ OVRD
RW
Power override. This bit field determines how the bridge responds when the slot power limit is
less than the amount of power required by the bridge and the devices behind the bridge. This
field shall be hardwired to 000b since XIO2213B does not support slot power limit functionality.
000 = Ignore slot power limit (default)
001 = Assert the PWR_OVRD terminal
010 = Disable secondary clocks selected by the clock mask register
011 = Disable secondary clocks selected by the clock mask register and assert the
PWR_OVRD terminal
100 = Respond with unsupported request to all transactions except for configuration
transactions (type 0 or type 1) and set slot power limit messages
101, 110, 111 = Reserved
(1)
(2)
90
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
These bits are reset only by a global reset (GRST) or the internally generated power-on reset.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 4-40. General Control Register Description (continued)
BIT
FIELD NAME
ACCESS
19 (1)
READ_
PREFETCH_ DIS
RW
DESCRIPTION
Read prefetch disable. This bit controls the prefetch functionality on PCI memory read
transactions.
0 = Prefetch to the next cache line boundary on a burst read (default)
1 = Fetch only a single DWORD on a burst read
Note: When this bit is set, the PREFETCH_4X bit in the TL control and diagnostic register shall
have no effect on the design. This bit shall only affect the XIO2213B when the
EN_CACHE_LINE_CHECK bit in the TL control and diagnostic register is set.
18:16 (1)
L0s_LATENCY
RW
L0s maximum exit latency. This field programs the maximum acceptable latency when exiting the
L0s state. This sets bits 8:6 (EP_L0S_LAT) in the device capabilities register (offset 94h, see
Section 4.50).
000 =
001 =
010 =
011 =
100 =
101 =
110 =
111 =
15:13 (1)
L1_LATENCY
RW
L1 maximum exit latency. This field programs the maximum acceptable latency when exiting the
L1 state. This sets bits 11:9 (EP_L1_LAT) in the device capabilities register (offset 94h, see
Section 4.50).
000 =
001 =
010 =
011 =
100 =
101 =
110 =
111 =
12 (1)
VC_CAP_EN
R
Less than 64 ns (default)
64 ns up to less than 128 ns
128 ns up to less than 256 ns
256 ns up to less than 512 ns
512 ns up to less than 1 s
1 s up to less than 2 s
2 s to 4 s
More than 4 s
Less than 1 s (default)
1 s up to less than 2 s
2 s up to less than 4 s
4 s up to less than 8 s
8 s up to less than 16 s
6 s up to less than 32 s
32 s to 64 s
More than 64 s
VC capability structure enable. This bit enables the VC capability structure by changing the next
offset field of the advanced error reporting capability register at offset 102h. This bit is a read only
0b indicating that the VC capability structure is permanently disabled.
0 = VC capability structure disabled (offset field = 000h)
1 = VC capability structure enabled (offset field = 150h)
11 (1)
BPCC_E
RW
Bus power clock control enable. This bit controls whether the secondary bus PCI clocks are
stopped when the XIO2213B is placed in the D3 state. It is assumed that if the secondary bus
clocks are required to be active that a reference clock continues to be provided on the PCIe
interface.
0 = Secondary bus clocks are not stopped in D3 (default).
1 = Secondary bus clocks are stopped on D3.
10
(2)
BEACON_
ENABLE
RW
Beacon enable. This bit controls the mechanism for waking up the physical PCIe link when in L2.
0 = WAKE mechanism is used exclusively. Beacon is not used (default).
1 = Beacon and WAKE mechanisms are used.
9:8
(1)
MIN_POWER_
SCALE
RW
Minimum power scale. This value is programmed to indicate the scale of bits 7:0
(MIN_POWER_VALUE).
00 =
01 =
10 =
11 =
7:0 (1)
MIN_POWER_
VALUE
Submit Documentation Feedback
RW
1.0x
0.1x
0.01x (default)
0.001x
Minimum power value. This value is programmed to indicate the minimum power requirements.
This value is multiplied by the minimum power scale field (bits 9:8) to determine the minimum
power requirements for the bridge. The default is 5Fh, indicating that XIO2213B requires 0.95 W
of power. This field can be reprogrammed through an EEPROM or the system BIOS.
Classic PCI Configuration Space
91
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.67 TI Proprietary Register
This read/write TI proprietary register is located at offset D8h and controls TI proprietary functions. This
register must not be changed from the specified default state. This register shall only be reset by FRST.
PCI register offset:
D8h
Register type:
Read only, Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.68 TI Proprietary Register
This read/write TI proprietary register is located at offset D9h and controls TI proprietary functions. This
register must not be changed from the specified default state. This register shall only be reset by FRST.
PCI register offset:
D9h
Register type:
Read only, Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.69 TI Proprietary Register
This read-only TI proprietary register is located at offset DAh and controls TI proprietary functions. This
register must not be changed from the specified default state. This register shall only be reset by FRST.
PCI register offset:
DAh
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
92
7
0
00h
6
0
Classic PCI Configuration Space
5
0
4
0
3
0
2
0
1
0
0
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.70 Arbiter Control Register
The arbiter control register controls the device's internal arbiter. The arbitration scheme used is a
two-tier rotational arbitration. The device is the only secondary bus master that defaults to the
higher-priority arbitration tier. See Table 4-41 for a complete description of the register contents.
PCI register offset:
DCh
Register type:
Read/Write
Default value:
40h
BIT NUMBER
RESET STATE
7
0
6
1
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-41. Arbiter Control Register Description
BIT
7
(1)
FIELD NAME
PARK
ACCESS
DESCRIPTION
RW
Bus parking mode. This bit determines where the internal arbiter parks the secondary bus.
When this bit is set, the arbiter parks the secondary bus on the bridge. When this bit is
cleared, the arbiter parks the bus on the last device mastering the secondary bus.
0 = Park the secondary bus on the last secondary bus master (default)
1 = Park the secondary bus on the bridge
6(1)
BRIDGE_TIER_SEL
RW
Bridge tier select. This bit determines in which tier the bridge is placed in the arbitration
scheme.
0 = Lowest-priority tier
1 = Highest-priority tier (default)
5:1(1)
0(1)
RSVD
RW
Reserved. These bits are reserved and must not be changed from their default value of
00000b.
TIER_SEL0
RW
GNT0 tier select. This bit determines in which tier GNT0 is placed in the arbitration
scheme.
0 = Lowest-priority tier (default)
1 = Highest-priority tier
(1)
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
Classic PCI Configuration Space
93
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.71 Arbiter Request Mask Register
The arbiter request mask register enables and disables support for requests from specific masters on the
secondary bus. The arbiter request mask register also controls if a request input is automatically masked
on an arbiter time-out. See Table 4-42 for a complete description of the register contents.
PCI register offset:
DDh
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-42. Arbiter Request Mask Register Description
BIT
7
(1)
FIELD NAME
ARB_TIMEOUT
ACCESS
DESCRIPTION
RW
Arbiter time-out. This bit enables the arbiter time-out feature. The arbiter time-out is
defined as the number of PCI clocks after the PCI bus has gone idle for a device to assert
FRAME before the arbiter assumes the device will not respond.
0 = Arbiter time disabled (default)
1 = Arbiter time-out set to 16 PCI clocks
6(1)
AUTO_MASK
RW
Automatic request mask. This bit enables automatic request masking when an arbiter
time-out occurs.
0 = Automatic request masking disabled (default)
1 = Automatic request masking enabled
5:1(1)
0(1)
RSVD
RW
Reserved. These bits are reserved and must not be changed from their default value of
00000b.
REQ0_MASK
RW
Request 0 (REQ0) mask. Setting this bit forces the internal arbiter to ignore requests
signal on request input 0.
0 = Use 1394a OHCI request (default)
1 = Ignore 1394a OHCI request
(1)
94
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Classic PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
4.72 Arbiter Time-Out Status Register
The arbiter time-out status register contains the status of each request (request 50) time-out. The time-out
status bit for the respective request is set if the device did not assert FRAME after the arbiter time-out
value. See Table 4-43 for a complete description of the register contents.
PCI register offset:
DEh
Register type:
Read/Clear
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 4-43. Arbiter Time-Out Status Register Description
BIT
7:6
5
FIELD NAME
RSVD
REQ5_TO
ACCESS
R
RCU
DESCRIPTION
Reserved. Returns 00b when read.
Request 5 time-out status
0 = No time-out
1 = Time-out has occurred.
4
REQ4_TO
RCU
Request 4 time-out status
0 = No time-out
1 = Time-out has occurred.
3
REQ3_TO
RCU
Request 3 time-out status
0 = No time-out
1 = Time-out has occurred.
2
REQ2_TO
RCU
Request 2 time-out status
0 = No time-out
1 = Time-out has occurred.
1
REQ1_TO
RCU
Request 1time-out status
0 = No time-out
1 = Time-out has occurred.
0
REQ0_TO
RCU
Request 0 time-out status
0 = No time-out
1 = Time-out has occurred.
Submit Documentation Feedback
Classic PCI Configuration Space
95
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
4.73 TI Proprietary Register
This read/write TI proprietary register is located at offset E0h and controls TI proprietary functions. This
register must not be changed from the specified default state. This register shall only be reset by FRST.
PCI register offset:
E0h
Register type:
Read only, Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.74 TI Proprietary Register
This read/write TI proprietary register is located at offset E2h and controls TI proprietary functions. This
register must not be changed from the specified default state. This register shall only be reset by FRST.
PCI register offset:
E2h
Register type:
Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
4.75 TI Proprietary Register
This read/clear TI proprietary register is located at offset E4h and controls TI proprietary functions. This
register must not be changed from the specified default state.
PCI register offset:
E4h
Register type:
Read/Clear
Default value:
BIT NUMBER
RESET STATE
96
15
0
0000h
14
0
Classic PCI Configuration Space
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
5
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
PCIe Extended Configuration Space
The programming model of the PCIe extended configuration space is compliant to the PCI Express Base
Specification and the PCI Express to PCI/PCI-X Bridge Specification programming models. The PCIe
extended configuration map uses the PCIe advanced error reporting capability and PCIe virtual channel
(VC) capability headers.
Sticky bits are reset by a global reset (GRST) or the internally-generated power-on reset. EEPROM
loadable bits are reset by a PCIe reset (PERST), GRST, or the internally-generated power-on reset. The
remaining register bits are reset by a PCIe hot reset, PERST, GRST, or the internally-generated power-on
reset.
Table 5-1. PCIe Extended Configuration Register Map
REGISTER NAME
OFFSET
Next capability offset/capability version
Advanced error reporting capabilities ID
100h
Uncorrectable error status register (1)
104h
(1)
Uncorrectable error mask
108h
Uncorrectable error severity(1)
10Ch
Correctable error status(1)
110h
(1)
114h
Correctable error mask
Advanced error capabilities and control(1)
118h
Header log(1)
11Ch
Header log(1)
120h
(1)
124h
Header log
(1)
5.1
Header log(1)
128h
Secondary uncorrectable error status(1)
12Ch
Secondary uncorrectable error mask(1)
130h
Secondary uncorrectable error severity(1)
134h
Secondary error capabilities and control(1)
138h
(1)
Secondary header log
13Ch
Secondary header log(1)
140h
Secondary header log(1)
144h
Secondary header log(1)
148h
Reserved
14Ch FFCh
This register shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Advanced Error Reporting Capability ID Register
This read-only register identifies the linked list item as the register for PCIe advanced error reporting
capabilities. The register returns 0001h when read.
PCIe extended register
offset:
100h
Register type:
Read only
Default value:
0001h
BIT NUMBER
RESET STATE
15
0
Submit Documentation Feedback
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
PCIe Extended Configuration Space
0
1
97
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
5.2
www.ti.com
Next Capability Offset/Capability Version Register
This read-only register identifies the next location in the PCIe extended capabilities link list. The upper 12
bits in this register shall be 000h, indicating that the advanced error reporting capability is the last
capability in the linked list. The least significant four bits identify the revision of the current capability block
as 1h.
PCIe extended register
offset:
102h
Register type:
Read only
Default value:
0001h
BIT NUMBER
RESET STATE
5.3
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Uncorrectable Error Status Register
The uncorrectable error status register reports the status of individual errors as they occur on the primary
PCIe interface. Software may only clear these bits by writing a 1b to the desired location. See Table 5-2
for a complete description of the register contents.
PCIe extended register
offset:
104h
Register type:
Read only, Read/Clear
Default value:
0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-2. Uncorrectable Error Status Register Description
BIT
98
ACCESS
R
DESCRIPTION
RSVD
20 (1)
UR_ERROR
RCU
Unsupported request error. This bit is asserted when an unsupported request is received.
19(1)
ECRC_ERROR
RCU
Extended CRC error. This bit is asserted when an extended CRC error is detected.
18
MAL_TLP
RCU
Malformed TLP. This bit is asserted when a malformed TLP is detected.
17(1)
RX_OVERFLOW
RCU
Receiver overflow. This bit is asserted when the flow control logic detects that the
transmitting device has illegally exceeded the number of credits that were issued.
16(1)
UNXP_CPL
RCU
Unexpected completion. This bit is asserted when a completion packet is received that
does not correspond to an issued request.
15(1)
CPL_ABORT
RCU
Completed abort. This bit is asserted when the bridge signals a completed abort.
14(1)
CPL_TIMEOUT
RCU
Completion time-out. This bit is asserted when no completion has been received for an
issued request before the time-out period.
13(1)
FC_ERROR
RCU
Flow control error. This bit is asserted when a flow control protocol error is detected either
during initialization or during normal operation.
12(1)
PSN_TLP
RCU
Poisoned TLP. This bit is asserted when a poisoned TLP is received.
11:5
RSVD
4(1)
DLL_ERROR
3:0
RSVD
(1)
(1)
FIELD NAME
31:21
R
RCU
R
Reserved. Returns 000 0000 0000b when read.
Reserved. Returns 000 0000b when read.
Data link protocol error. This bit is asserted if a data link layer protocol error is detected.
Reserved. Returns 0h when read.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
PCIe Extended Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
5.4
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Uncorrectable Error Mask Register
The uncorrectable error mask register controls the reporting of individual errors as they occur. When a
mask bit is set to 1b, the corresponding error status bit is not set, PCIe error messages are blocked, the
header log is not loaded, and the first error pointer is not updated. See Table 5-3 for a complete
description of the register contents.
PCIe extended register offset: 108h
Register type:
Read only, Read/Write
Default value:
0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-3. Uncorrectable Error Mask Register Description
BIT
FIELD NAME
31:21
RSVD
20 (1)
UR_ERROR_MASK
ACCESS
R
RW
DESCRIPTION
Reserved. Returns 000 0000 0000b when read.
Unsupported request error mask
0 = Error condition is unmasked (default)..
1 = Error condition is masked.
19(1)
ECRC_ERROR_MASK
RW
Extended CRC error mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
18(1)
MAL_TLP_MASK
RW
Malformed TLP mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
17(1)
RX_OVERFLOW_MASK
RW
Receiver overflow mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
16(1)
UNXP_CPL_MASK
RW
Unexpected completion mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
15(1)
CPL_ABORT_MASK
RW
Completer abort mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
14(1)
CPL_TIMEOUT_MASK
RW
Completion time-out mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
13(1)
FC_ERROR_MASK
RW
Flow control error mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
12(1)
PSN_TLP_MASK
RW
Poisoned TLP mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
11:5
RSVD
4(1)
DLL_ERROR_MASK
R
RW
Reserved. Returns 000 0000b when read.
Data link protocol error mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
3:0
(1)
RSVD
R
Reserved. Returns 0h when read.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
PCIe Extended Configuration Space
99
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
5.5
www.ti.com
Uncorrectable Error Severity Register
The uncorrectable error severity register controls the reporting of individual errors as ERR_FATAL or
ERR_NONFATAL. When a bit is set, the corresponding error condition is identified as fatal. When a bit is
cleared, the corresponding error condition is identified as nonfatal. See Table 5-4 for a complete
description of the register contents.
PCIe extended register offset:
10Ch
Register type:
Read only, Read/Write
Default value:
0006 2011h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
1
17
1
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
1
0
0
0
0
0
0
0
1
1
0
0
0
1
Table 5-4. Uncorrectable Error Severity Register Description
BIT
FIELD NAME
31:21
RSVD
20 (1)
UR_ERROR_SEVRO
ACCESS
R
RW
DESCRIPTION
Reserved. Returns 000 0000 0000b when read.
Unsupported request error severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
19(1)
ECRC_ERROR_SEVRR
RW
Extended CRC error severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
18(1)
MAL_TLP_SEVR
RW
Malformed TLP severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
17(1)
RX_OVERFLOW_SEVR
RW
Receiver overflow severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
16(1)
UNXP_CPL_SEVRP
RW
Unexpected completion severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
15(1)
CPL_ABORT_SEVR
RW
Completed abort severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
14(1)
CPL_TIMEOUT_SEVR
RW
Completion time-out severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
13(1)
FC_ERROR_SEVR
RW
Flow control error severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
12(1)
PSN_TLP_SEVR
RW
Poisoned TLP severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
11:6
RSVD
R
Reserved. Returns 000 000b when read.
5
RSVD
R
Reserved. Returns 1h when read.
4(1)
DLL_ERROR_SEVR
RW
Data link protocol error severity
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL.
3:1
RSVD
R
Reserved. Returns 000b when read.
0
RSVD
R
Reserved. Returns 1h when read.
(1)
100
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
PCIe Extended Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
5.6
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Correctable Error Status Register
The correctable error status register reports the status of individual errors as they occur. Software may
only clear these bits by writing a 1b to the desired location. See Table 5-5 for a complete description of
the register contents.t
PCIe extended register
offset:
110h
Register type:
Read only, Read/Clear
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-5. Correctable Error Status Register Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
31:14
RSVD
R
13
ANFES
RCU
Advisory nonfatal error status. This bit is asserted when an advisory nonfatal error has been
reported.
REPLAY_TMOUT
RCU
Replay timer time-out. This bit is asserted when the replay timer expires for a pending request
or completion that has not been acknowledged.
12
(1)
(1)
R
Reserved. Returns 000 0000 0000 0000 0000b when read.
11:9
RSVD
8(1)
REPLAY_ROLL
RCU
REPLAY_NUM rollover. This bit is asserted when the replay counter rolls over after a pending
request or completion has not been acknowledged.
7(1)
BAD_DLLP
RCU
Bad DLLP error. This bit is asserted when an 8b/10b error was detected by the PHY during
the reception of a DLLP.
6(1)
BAD_TLP
RCU
Bad TLP error. This bit is asserted when an 8b/10b error was detected by the PHY during the
reception of a TLP.
5:1
RSVD
0(1)
RX_ERROR
R
RCU
Reserved. Returns 000b when read.
Reserved. Returns 00000b when read.
Receiver error. This bit is asserted when an 8b/10b error is detected by the PHY at any time.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
PCIe Extended Configuration Space
101
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
5.7
www.ti.com
Correctable Error Mask Register
The correctable error mask register controls the reporting of individual errors as they occur. When a mask
bit is set to 1b, the corresponding error status bit is not set, PCIe error messages are blocked, the header
log is not loaded, and the first error pointer is not updated. See Table 5-6 for a complete description of the
register contents.
PCIe extended register
offset:
114h
Register type:
Read only, Read/Write
Default value:
0000 2000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-6. Correctable Error Mask Register Description
BIT
31:14
13
FIELD NAME
RSVD
ANFEM
ACCESS
R
RW
DESCRIPTION
Reserved. Returns 000 0000 0000 0000 0000b when read.
Advisory nonfatal error mask
0 = Error condition is unmasked.
1 = Error condition is masked (default).
12 (1)
REPLAY_TMOUT_MASK
RW
Replay timer time-out mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
11:9
RSVD
8(1)
REPLAY_ROLL_MASK
R
RW
Reserved. Returns 000b when read.
REPLAY_NUM rollover mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
7(1)
BAD_DLLP_MASK
RW
Bad DLLP error mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
6(1)
BAD_TLP_MASK
RW
Bad TLP error mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
5:1
(1)
0
RSVD
RX_ERROR_MASK
R
RW
Reserved. Returns 00000b when read.
Receiver error mask
0 = Error condition is unmasked (default).
1 = Error condition is masked.
(1)
102
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
PCIe Extended Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
5.8
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Advanced Error Capabilities and Control Register
The advanced error capabilities and control register allows the system to monitor and control the
advanced error reporting capabilities. See Table 5-7 for a complete description of the register contents.
PCIe extended register
offset:
118h
Register type:
Read only, Read/Write
Default value:
0000 00A0h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
Table 5-7. Advanced Error Capabilities and Control Register Description
BIT
FIELD NAME
31:9
RSVD
8 (1)
ECRC_CHK_EN
ACCESS
R
RW
DESCRIPTION
Reserved. Returns 000 0000 0000 0000 0000 0000b when read.
Extended CRC check enable
0 = Extended CRC checking is disabled.
1 = Extended CRC checking is enabled.
7
ECRC_CHK_CAPABLE
6(1)
R
ECRC_GEN_EN
RW
Extended CRC check capable. This read-only bit returns a value of 1b indicating that the
bridge is capable of checking extended CRC information.
Extended CRC generation enable
0 = Extended CRC generation is disabled.
1 = Extended CRC generation is enabled.
5
ECRC_GEN_CAPABLE
4:0(1)
(1)
5.9
R
FIRST_ERR
RU
Extended CRC generation capable. This read-only bit returns a value of 1b indicating
that the bridge is capable of generating extended CRC information.
First error pointer. This 5-bit value reflects the bit position within the uncorrectable error
status register (offset 104h, see Section 5.3) corresponding to the class of the first error
condition that was detected.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Header Log Register
The header log register stores the TLP header for the packet that lead to the most recently detected error
condition. Offset 11Ch contains the first DWORD. Offset 128h contains the last DWORD (in the case of a
4DW TLP header). Each DWORD is stored with the least significant byte representing the earliest
transmitted. This register shall only be reset by a fundamental reset (FRST).
PCIe extended register offset:
11Ch, 120h, 124h, and 128h
Register type:
Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Submit Documentation Feedback
PCIe Extended Configuration Space
103
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
5.10 Secondary Uncorrectable Error Status Register
The secondary uncorrectable error status register reports the status of individual PCI bus errors as they
occur. Software may only clear these bits by writing a 1b to the desired location. See Table 5-8 for a
complete description of the register contents.
PCIe extended register offset:
12Ch
Register type:
Read only, Read/Clear
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-8. Secondary Uncorrectable Error Status Register Description
BIT
FIELD NAME
ACCESS
31:13
RSVD
12 (1)
SERR_DETECT
RCU
SERR assertion detected. This bit is asserted when the bridge detects the assertion of
SERR on the secondary bus.
11(1)
PERR_DETECT
RCU
PERR assertion detected. This bit is asserted when the bridge detects the assertion of
PERR on the secondary bus.
10(1)
DISCARD_TIMER
RCU
Delayed transaction discard timer expired. This bit is asserted when the discard timer
expires for a pending delayed transaction that was initiated on the secondary bus.
9(1)
UNCOR_ADDR
RCU
Uncorrectable address error. This bit is asserted when the bridge detects a parity error
during the address phase of an upstream transaction.
8
(1)
104
RSVD
7(1)
UNCOR_DATA
6:4
RSVD
R
DESCRIPTION
R
RCU
R
Reserved. Returns 000 0000 0000 0000 0000b when read.
Reserved. Returns 0b when read.
Uncorrectable data error. This bit is asserted when the bridge detects a parity error during
a data phase of an upstream write transaction, or when the bridge detects the assertion of
PERR when forwarding read completion data to a PCI device.
Reserved. Returns 000b when read.
(1)
3
MASTER_ABORT
RCU
Received master abort. This bit is asserted when the bridge receives a master abort on
the PCI interface.
2(1)
TARGET_ABORT
RCU
Received target abort. This bit is asserted when the bridge receives a target abort on the
PCI interface.
1:0
RSVD
R
Reserved. Returns 00b when read.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
PCIe Extended Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
5.11 Secondary Uncorrectable Error Mask Register
The secondary uncorrectable error mask register controls the reporting of individual errors as they occur.
When a mask bit is set to 1b, the corresponding error status bit is not set, PCIe error messages are
blocked, the header log is not loaded, and the first error pointer is not updated. See Table 5-9 for a
complete description of the register contents.
PCIe extended register offset:
130h
Register type:
Read only, Read/Write
Default value:
0000 17A8h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
1
0
1
1
1
1
0
1
0
1
0
0
0
Table 5-9. Secondary Uncorrectable Error Mask Register Description
BIT
FIELD NAME
ACCESS
R
DESCRIPTION
31:14
RSVD
13 (1)
BRIDGE_ERROR_MASK
RW
Reserved. Returns 00 0000 0000 0000 0000b when read.
Internal bridge error. This mask bit is associated with a PCI-X error and has no effect
on the bridge.
12(1)
SERR_DETECT_MASK
RW
SERR assertion detected
0 = Error condition is unmasked.
1 = Error condition is masked (default).
11(1)
PERR_DETECT_MASK
RW
PERR assertion detectedi
0 = Error condition is unmasked.
1 = Error condition is masked (default).
10(1)
DISCARD_TIMER_MASK
RW
Delayed transaction discard timer expired
0 = Error condition is unmasked.
1 = Error condition is masked (default).
9(1)
UNCOR_ADDR_MASK
RW
Uncorrectable address error
0 = Error condition is unmasked.
1 = Error condition is masked (default).
8(1)
ATTR_ERROR_MASK
RW
Uncorrectable attribute error. This mask bit is associated with a PCI-X error and has
no effect on the bridge.
7(1)
UNCOR_DATA_MASK
RW
Uncorrectable data error
0 = Error condition is unmasked.
1 = Error condition is masked (default).
6(1)
SC_MSG_DATA_MASK
RW
Uncorrectable split completion message data error. This mask bit is associated with a
PCI-X error and has no effect on the bridge.
5(1)
SC_ERROR_MASK
RW
Unexpected split completion error. This mask bit is associated with a PCI-X error and
has no effect on the bridge.
4
RSVD
(1)
MASTER_ABORT_MASK
3
R
RW
Reserved. Returns 0b when read.
Received master abort
0 = Error condition is unmasked.
1 = Error condition is masked (default).
2(1)
TARGET_ABORT_MASK
RW
Received target abort
0 = Error condition is unmasked.
1 = Error condition is masked (default).
1(1)
0
(1)
SC_MSTR_ABORT_MASK
RSVD
RW
R
Master abort on split completion. This mask bit is associated with a PCI-X error and
has no effect on the bridge.
Reserved. Returns 0b when read.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
PCIe Extended Configuration Space
105
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
5.12 Secondary Uncorrectable Error Severity
The uncorrectable error severity register controls the reporting of individual errors as ERR_FATAL or
ERR_NONFATAL. When a bit is set, the corresponding error condition is identified as fatal. When a bit is
cleared, the corresponding error condition is identified as nonfatal. See Table 5-10 for a complete
description of the register contents.
PCIe extended register offset: 134h
Register type:
Read only, Read/Write
Default value:
0000 1340h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
1
0
0
1
1
0
1
0
0
0
0
0
0
Table 5-10. Secondary Uncorrectable Error Severity Register Description
BIT
FIELD NAME
ACCESS
R
DESCRIPTION
31:14
RSVD
13 (1)
BRIDGE_ERROR_SEVR
RW
Reserved. Returns 00 0000 0000 0000 0000b when read.
Internal bridge error. This severity bit is associated with a PCI-X error and has no effect
on the bridge.
12(1)
SERR_DETECT_SEVR
RW
SERR assertion detected
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL (default).
11(1)
PERR_DETECT_SEVR
RW
PERR assertion detected
0 = Error condition is signaled using ERR_NONFATAL (default).
1 = Error condition is signaled using ERR_FATAL.
10(1)
DISCARD_TIMER_SEVR
RW
Delayed transaction discard timer expired
0 = Error condition is signaled using ERR_NONFATAL (default).
1 = Error condition is signaled using ERR_FATAL.
9(1)
UNCOR_ADDR_SEVR
RW
Uncorrectable address error
0 = Error condition is signaled using ERR_NONFATAL.
1 = Error condition is signaled using ERR_FATAL (default).
8(1)
ATTR_ERROR_SEVR
RW
Uncorrectable attribute error. This severity bit is associated with a PCI-X error and has
no effect on the bridge.
7(1)
UNCOR_DATA_SEVR
RW
Uncorrectable data error
0 = Error condition is signaled using ERR_NONFATAL (default).
1 = Error condition is signaled using ERR_FATAL.
6(1)
SC_MSG_DATA_SEVR
RW
Uncorrectable split completion message data error. This severity bit is associated with
a PCI-X error and has no effect on the bridge.
5(1)
SC_ERROR_SEVR
RW
Unexpected split completion error. This severity bit is associated with a PCI-X error and
has no effect on the bridge.
4
RSVD
(1)
MASTER_ABORT_SEVR
3
R
RW
Reserved. Returns 0b when read.
Received master abort
0 = Error condition is signaled using ERR_NONFATAL (default).
1 = Error condition is signaled using ERR_FATAL.
2(1)
TARGET_ABORT_SEVR
RW
Received target abort
0 = Error condition is signaled using ERR_NONFATAL (default).
1 = Error condition is signaled using ERR_FATAL.
1(1)
0
(1)
106
SC_MSTR_ABORT_SEVR
RW
RSVD
R
Master abort on split completion. This severity bit is associated with a PCI-X error and
has no effect on the bridge.
Reserved. Returns 0b when read.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
PCIe Extended Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
5.13 Secondary Error Capabilities and Control Register
The secondary error capabilities and control register allows the system to monitor and control the
secondary advanced error reporting capabilities. See Table 5-11 for a complete description of the register
contents.
PCIe extended register offset:
138h
Register type:
Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-11. Secondary Error Capabilities and Control Register Description
BIT
(1)
FIELD NAME
31:5
RSVD
4:0 (1)
SEC_FIRST_ERR
ACCESS
R
RU
DESCRIPTION
Reserved. Return 000 0000 0000 0000 0000 0000 0000b when read.
First error pointer. This 5-bit value reflects the bit position within the secondary
uncorrectable error status register (offset12Ch, see Section 5.10) corresponding to the
class of the first error condition that was detected.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
PCIe Extended Configuration Space
107
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
5.14 Secondary Header Log Register
The secondary header log register stores the transaction address and command for the PCI bus cycle that
led to the most recently detected error condition. Offset 13Ch accesses register bits 31:0. Offset 140h
accesses register bits 63:32. Offset 144h accesses register bits 95:64. Offset 148h accesses register bits
127:96. See Table 5-12 for a complete description of the register contents.
PCIe extended register offset:
13Ch, 140h, 144h, and 148h
Register type:
Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
127
0
126
0
125
0
124
0
123
0
122
0
121
0
120
0
119
0
118
0
117
0
116
0
115
0
114
0
113
0
112
0
BIT NUMBER
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT NUMBER
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT NUMBER
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT NUMBER
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT NUMBER
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT NUMBER
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 5-12. Secondary Header Log Register Description
BIT
FIELD NAME
127:64 (1) ADDRESS
63:44
RSVD
ACCESS
RU
R
DESCRIPTION
Transaction address. The 64-bit value transferred on AD[31:0] during the first and
second address phases. The first address phase is logged to 95:64 and the second
address phase is logged to 127:96. In the case of a 32-bit address, bits 127:96 are set
to 0.
Reserved. Returns 0 0000h when read.
(1)
43:40
UPPER_CMD
RU
Transaction command upper. Contains the status of the C/BE terminals during the
second address phase of the PCI transaction that generated the error if using a
dual-address cycle.
39:36(1)
LOWER_CMD
RU
Transaction command lower. Contains the status of the C/BE terminals during the first
address phase of the PCI transaction that generated the error.
35:0
(1)
108
TRANS_ATTRIBUTE
R
Transaction attribute. Because the bridge does not support the PCI-X attribute
transaction phase, these bits have no function, and return 0 0000 0000h when read.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
PCIe Extended Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
6
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Memory-Mapped TI Proprietary Register Space
The programming model of the memory-mapped TI proprietary register space is unique to this device.
These custom registers are specifically designed to provide enhanced features associated with upstream
isochronous applications.
Sticky bits are reset by a fundamental reset (FRST).
Table 6-1. Device Control Memory Window Register Map
REGISTER NAME
OFFSET
Reserved
Revision ID
Device control map ID
Reserved
GPIO data (1)
(1)
Serial-bus control and status
(1)
6.1
GPIO control(1)
(1)
Serial-bus word address(1)
Serial-bus slave address
00h
04h-3Ch
40h
Serial-bus data(1)
44h
This register shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Device Control Map ID Register
The device control map ID register identifies the TI proprietary layout for this device control map. The
value 04h identifies this as a PCIe-to-PCI bridge without isochronous capabilities.
Device control memory window register
offset:
00h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
7
0
Submit Documentation Feedback
04h
6
0
5
0
4
0
3
0
2
1
1
0
0
0
Memory-Mapped TI Proprietary Register Space
109
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
6.2
www.ti.com
Revision ID Register
Device control memory window register
offset:
01h
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
6.3
7
0
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
GPIO Control Register
This register controls the direction of the eight GPIO terminals. This register has no effect on the behavior
of GPIO terminals that are enabled to perform secondary functions. The secondary functions share GPIO4
(SCL) and GPIO5 (SDA). This register is an alias of the GPIO control register in the classic PCI
configuration space (offset B4h, see Section 4.60). See Table 6-2 for a complete description of the
register contents.
Device control memory window register
offset:
40h
Register type:
Read only, Read/Write
Default value:
BIT NUMBER
RESET STATE
15
0
0000h
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 6-2. GPIO Control Register Description
BIT
FIELD NAME
15:8
RSVD
7 (1)
GPIO7_DIR
ACCESS
R
RW
DESCRIPTION
Reserved. Returns 00h when read.
GPIO 7 data direction. This bit selects whether GPIO7 is in input or output mode.
0 = Input (default)
1 = Output
6(1)
GPIO6_DIR
RW
GPIO 6 data direction. This bit selects whether GPIO6 is in input or output mode.
0 = Input (default)
1 = Output
5(1)
GPIO5_DIR
RW
GPIO 5 data direction. This bit selects whether GPIO5 is in input or output mode.
0 = Input (default)
1 = Output
4(1)
GPIO4_DIR
RW
GPIO 4 data direction. This bit selects whether GPIO4 is in input or output mode.
0 = Input (default)
1 = Output
3(1)
GPIO3_DIR
RW
GPIO 3 data direction. This bit selects whether GPIO3 is in input or output mode.
0 = Input (default)
1 = Output
2(1)
GPIO2_DIR
RW
GPIO 2 data direction. This bit selects whether GPIO2 is in input or output mode.
0 = Input (default)
1 = Output
1(1)
GPIO1_DIR
RW
GPIO 1 data direction. This bit selects whether GPIO1 is in input or output mode.
0 = Input (default)
1 = Output
0(1)
GPIO0_DIR
RW
GPIO 0 data direction. This bit selects whether GPIO0 is in input or output mode.
0 = Input (default)
1 = Output
(1)
110
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Memory-Mapped TI Proprietary Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
6.4
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
GPIO Data Register
This register reads the state of the input-mode GPIO terminals and changes the state of the output-mode
GPIO terminals. Writing to a bit that is in input mode or is enabled for a secondary function is ignored. The
secondary functions share GPIO4 (SCL) and GPIO5 (SDA). The default value at power up depends on
the state of the GPIO terminals as they default to general-purpose inputs. This register is an alias of the
GPIO data register in the classic PCI configuration space (offset B6h, see Section 4.61). See Table 6-3 for
a complete description of the register contents.
Device control memory window register offset:
42h
Register type:
Read only, Read/Write
Default value:
00XXh
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
x
6
x
5
x
4
x
3
x
2
x
1
x
0
x
Table 6-3. GPIO Data Register Description
BIT
(1)
FIELD NAME
ACCESS
R
DESCRIPTION
15:8
RSVD
7 (1)
GPIO7_Data
RW
Reserved
GPIO 7 data. This bit reads the state of GPIO7 when in input mode or changes the state
of GPIO7 when in output mode.
6(1)
GPIO6_Data
RW
GPIO 6 data. This bit reads the state of GPIO6 when in input mode or changes the state
of GPIO6 when in output mode.
5(1)
GPIO5_Data
RW
GPIO 5 data. This bit reads the state of GPIO5 when in input mode or changes the state
of GPIO5 when in output mode.
4(1)
GPIO4_Data
RW
GPIO 4 data. This bit reads the state of GPIO4 when in input mode or changes the state
of GPIO4 when in output mode.
3(1)
GPIO3_Data
RW
GPIO 3 data. This bit reads the state of GPIO3 when in input mode or changes the state
of GPIO3 when in output mode.
2(1)
GPIO2_Data
RW
GPIO 2 data. This bit reads the state of GPIO2 when in input mode or changes the state
of GPIO2 when in output mode.
1(1)
GPIO1_Data
RW
GPIO 1 data. This bit reads the state of GPIO1 when in input mode or changes the state
of GPIO1 when in output mode.
0(1)
GPIO0_Data
RW
GPIO 0 data. This bit reads the state of GPIO0 when in input mode or changes the state
of GPIO0 when in output mode.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
Memory-Mapped TI Proprietary Register Space
111
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
6.5
www.ti.com
Serial-Bus Data Register
The serial-bus data register is used to read and write data on the serial-bus interface. When writing data
to the serial bus, this register must be written before writing to the serial-bus address register to initiate the
cycle. When reading data from the serial bus, this register will contain the data read after the REQBUSY
(bit 5 serial-bus control register) bit is cleared. This register is an alias for the serial-bus data register in
the PCI header. This register shall only be reset by FRST.
Device control memory window register offset:
44h
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
6.6
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Serial-Bus Word Address Register
The value written to the serial-bus index register represents the byte address of the byte being read or
written from the serial-bus device. The serial-bus index register must be written before the before initiating
a serial bus cycle by writing to the serial-bus slave address register. This register is an alias for the
serial-bus index register in the PCI header. This register shall only be reset by FRST.
Device control memory window register offset:
45h
Register type:
Read/Write
Default value:
00h
BIT NUMBER
RESET STATE
6.7
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Serial-Bus Slave Address Register
The serial-bus slave address register is used to indicate the address of the device being targeted by the
serial-bus cycle. This register also indicates if the cycle will be a read or a write cycle. Writing to this
register initiates the cycle on the serial interface. This register is an alias for the serial-bus slave address
register in the PCI header.
Device control memory window register offset:
46h
Register type:
Read/Write
Default value:
BIT NUMBER
RESET STATE
7
0
00h
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 6-4. Serial-Bus Slave Address Register Descriptions
BIT
7:1 (1)
0(1)
FIELD NAME
ACCESS
DESCRIPTION
SLAVE_ADDR
RW
Serial-bus slave address. This 7-bit field is the slave address for a serial-bus read or write
transaction. The default value for this field is 000 0000b.
RW_CMD
RW
Read/write command. This bit determines if the serial-bus cycle is a read or a write cycle.
0 = A single-byte write is requested (default) .
1 = A single-byte read is requested.
(1)
112
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Memory-Mapped TI Proprietary Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
6.8
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Serial-Bus Control and Status Register
The serial-bus control and status register is used to control the behavior of the serial-bus interface. This
register also provides status information about the state of the serial bus. This register is an alias for the
serial-bus control and status register in the PCI header.
Device control memory window register offset:
47h
Register type:
Read only, Read/Write, Read/Clear
Default value:
00h
BIT NUMBER
RESET STATE
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 6-5. Serial-Bus Control and Status Register Description
BIT
(1)
7
FIELD NAME
PROT_SEL
ACCESS
RW
DESCRIPTION
Protocol select. This bit selects the serial-bus address mode used.
0 = Slave address and word address are sent on the serial bus (default).
1 = Only the slave address is sent on the serial bus.
6
RSVD
5
REQBUSY
R
RU
Reserved. Returns 0b when read.
Requested serial-bus access busy. This bit is set when a software-initiated serial-bus cycle
is in progress.
0 = No serial-bus cycle
1 = Serial-bus cycle in progresss
4(1)
ROMBUSY
RU
Serial EEPROM access busy. This bit is set when the serial EEPROM circuitry in the
bridge is downloading register defaults from a serial EEPROM.
0 = No EEPROM activity
1 = EEPROM download in progress
3(1)
SBDETECT
RWU
Serial EEPROM detected. This bit enables the serial-bus interface. The value of this bit
controls whether the GPIO4/SCL and GPIO5/SDA terminals are configured as GPIO
signals or as serial-bus signals. This bit is automatically set to 1b when a serial EEPROM
is detected.
Note: A serial EEPROM is only detected once following PERST.
0 = No EEPROM present, EEPROM load process does not happen. GPIO4//SCL and
GPIO5//SDA terminals are configured as GPIO signals.
1 = EEPROM present, EEPROM load process takes place. GPIO4/SCL and
GPIO5/SDA terminals are configured as serial-bus signals.
2(1)
SBTEST
RW
Serial-bus test. This bit is used for internal test purposes. This bit controls the clock source
for the serial interface clock.
0 = Serial-bus clock at normal operating frequency ~60 kHz (default)
1 = Serial-bus clock frequency increased for test purposes ~4 MHz
(1)
1
SB_ERR
RCU
Serial-bus error. This bit is set when an error occurs during a software-initiated serial-bus
cycle.
0 = No error
1 = Serial-bus error
0(1)
ROM_ERR
RCU
Serial EEPROM load error. This bit is set when an error occurs while downloading
registers from a serial EEPROM.
0 = No error
1 = EEPROM load error
(1)
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
Submit Documentation Feedback
Memory-Mapped TI Proprietary Register Space
113
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7
www.ti.com
1394 OHCI PCI Configuration Space
The 1394 OHCI core is integrated as a PCI device behind the PCIe to PCI bridge. The configuration
header for the 1394b OHCI portion of the design is compliant with the PCI specification as a standard
header. Table 7-1 shows the configuration header that includes both the predefined portion of the
configuration space and the user-definable registers.
Since the 1394 OHCI configuration space is accessed over the bridge secondary PCI bus, PCIe type 1
configuration read and write transactions are required when accessing these registers. The 1394 OHCI
configuration register map is accessed as device number 0 and function number 0. Of course, the bus
number is determined by the value that is loaded into the secondary bus number field at offset 19h within
the PCIe configuration register map.
Sticky bits are reset by a fundamental reset (FRST). The remaining register bits are reset by a PCIe hot
reset, PERST, GRST, or the internally-generated power-on reset.
Table 7-1. 1394 OHCI Configuration Register Map
REGISTER NAME
OFFSET
Device ID
Vendor ID
00h
Status
Command
04h
Class code
Revision ID
BIST
Header type
Latency timer
08h
Cache line size
OHCI base address
10h
TI extension base address
14h
CIS base address
18h
Reserved
1Ch-27h
CIS pointer
28h
Subsystem ID (1)
Subsystem vendor ID(1)
2Ch
Reserved
30h
Reserved
Power management capabilities
pointer
Reserved
(1)
Maximum latency
Minimum grant
Power management capabilities
Interrupt pin
Interrupt line
Next item pointer
Capability ID
(1)
PMCSR_BSE
Power management control and status
44h
48h
4Ch-E7h
Multifunction select
E8h
(1)
ECh
PCI PHY control
PCI miscellaneous configuration(1)
F0h
Link enhancement control(1)
F4h
(1)
Subsystem access
TI proprietary
114
3Ch
40h
Reserved
(1)
34h
38h
(1)
OHCI control
Power management data
(reserved)
0Ch
F8h
FCh
This register shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
7.1
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Vendor ID Register
The vendor ID register contains a value allocated by the PCI SIG and identifies the manufacturer of the
OHCI controller. The vendor ID assigned to TI is 104Ch.
PCI register offset:
00h
Register type:
Read only
Default value:
104Ch
BIT NUMBER
RESET STATE
7.2
15
0
14
0
13
0
12
1
11
0
10
0
9
0
8
0
7
0
6
1
5
0
4
0
3
1
2
1
1
0
0
0
Device ID Register
The device ID register contains a value assigned to the 1394 OHCI function by TI. The device
identification for the 1394 OHCI function is 823Fh.
PCI register offset:
02h
Register type:
Read only
Default value:
823Fh
BIT NUMBER
RESET STATE
15
1
Submit Documentation Feedback
14
0
13
0
12
0
11
0
10
0
9
1
8
0
7
0
6
0
5
1
4
1
3
1
2
1
1
1
1394 OHCI PCI Configuration Space
0
1
115
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7.3
www.ti.com
Command Register
The command register provides control over the 1394b OHCI function interface to the PCI bus. All bit
functions adhere to the definitions in the PCI Local Bus Specification, as shown in the following bit
descriptions. See Table 7-2 for a complete description of the register contents.
PCI register offset:
04h
Register type:
Read/Write, Read only
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 7-2. Command Register Description
BIT
15-11
FIELD NAME
TYPE
DESCRIPTION
RSVD
R
Reserved. Return 0 0000b when read.
10
INT_DISABLE
R
Interrupt disable. When bit 10 is set to 1b, the OHCI controller is disabled from asserting an
interrupt. When cleared, the OHCI controller is able to send interrupts normally. This default
value for this bit is 0b.
9
FBB_ENB
R
Fast back-to-back enable. The 1394b OHCI controller does not generate fast back-to-back
transactions; therefore, bit 9 returns 0b when read.
8
SERR_ENB
RW
7
STEP_ENB
R
6
PERR_ENB
RW
5
VGA_ENB
R
4
MWI_ENB
RW
3
SPECIAL
R
Special cycle enable. The 1394b OHCI controller function does not respond to special cycle
transactions; therefore, bit 3 returns 0b when read.
2
MASTER_ENB
RW
Bus master enable. When bit 2 is set to 1b, the 1394b OHCI controller is enabled to initiate
cycles on the PCI bus. The default value for this bit is 0b.
1
MEMORY_ENB
RW
Memory response enable. Setting bit 1 to 1b enables the 1394b OHCI controller to respond to
memory cycles on the PCI bus. This bit must be set to access OHCI registers. The default
value for this bit is 0b.
0
IO_ENB
116
R
PCI_SERR enable. When bit 8 is set to 1b, the 1394b OHCI controller PCI_SERR driver is
enabled. PCI_SERR can be asserted after detecting an address parity error on the PCI bus.
The default value for this bit is 0b.
Address/data stepping control. The 1394b OHCI controller does not support address/data
stepping; therefore, bit 7 is hardwired to 0b.
Parity error enable. When bit 6 is set to 1b, the 1394b OHCI controller is enabled to drive
PCI_PERR response to parity errors through the PCI_PERR signal. The default value for this
bit is 0b.
VGA palette snoop enable. The 1394b OHCI controller does not feature VGA palette snooping;
therefore, bit 5 returns 0b when read.
Memory write and invalidate enable. When bit 4 is set to 1b, the OHCI controller is enabled to
generate MWI PCI bus commands. If this bit is cleared, the 1394b OHCI controller generates
memory write commands instead. The default value for this bit is 0b.
I/O space enable. The 1394b OHCI controller does not implement any I/O-mapped functionality;
therefore, bit 0 returns 0b when read.
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
7.4
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Status Register
The status register provides status over the 1394b OHCI controller interface to the PCI bus. All bit
functions adhere to the definitions in the PCI Local Bus Specification, as shown in the following bit
descriptions. See Table 7-3 for a complete description of the register contents.
PCI register offset:
06h
Register type:
Read/Clear/Update, Read only
Default value:
0230h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
1
8
0
7
0
6
0
5
1
4
1
3
0
2
0
1
0
0
0
Table 7-3. Status Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15
PAR_ERR
RCU
Detected parity error. Bit 15 is set to 1b when either an address parity or data parity error is
detected.
14
SYS_ERR
RCU
Signaled system error. Bit 14 is set to 1b when PCI_SERR is enabled and the 1394b OHCI
controller has signaled a system error to the host.
13
MABORT
RCU
Received master abort. Bit 13 is set to 1b when a cycle initiated by the 1394b OHCI controller
on the PCI bus has been terminated by a master abort.
12
TABORT_REC
RCU
Received target abort. Bit 12 is set to 1b when a cycle initiated by the 1394b OHCI controller on
the PCI bus was terminated by a target abort.
11
TABORT_SIG
RCU
Signaled target abort. Bit 11 is set to 1b by the 1394b OHCI controller when it terminates a
transaction on the PCI bus with a target abort.
10-9
PCI_SPEEDO
R
8
DATAPAR
RCU
DEVSEL timing. Bits 10 and 9 encode the timing of PCI_DEVSEL and are hardwired to 01b,
indicating that the 1394b OHCI controller asserts this signal at a medium speed on
nonconfiguration cycle accesses.
Data parity error detected. Bit 8 is set to 1b when the following conditions have been met:
a. PCI_PERR was asserted by any PCI device including the OHCI controller.
b. 1394b OHCI controller was the bus master during the data parity error.
c. Bit 6 (PERR_EN) in the command register at offset 04h in the PCI configuration space
(see Section 7.3, Command Register) is set to 1b.
7
FBB_CAP
R
Fast back-to-back capable. The 1394b OHCI controller cannot accept fast back-to-back
transactions; therefore, bit 7 is hardwired to 0b.
6
UDF
R
User-definable features (UDFs) supported. The 1394b OHCI controller does not support the
UDF; therefore, bit 6 is hardwired to 0b.
5
66MHZ
R
66-MHz capable. The 1394b OHCI controller operates at a maximum PCI_CLK frequency of 66
MHz; therefore, bit 5 is hardwired to 1b.
4
CAPLIST
R
Capabilities list. Bit 4 returns 1b when read, indicating that capabilities additional to standard
PCI are implemented. The linked list of PCI power-management capabilities is implemented in
this function.
3
INT_STATUS
RU
Interrupt status. This bit reflects the interrupt status of the function. Only when bit 10
(INT_DISABLE) in the command register (PCI offset 04h, see Section 4.3) is a 0 and this bit is
a 1, is the functions INTx signal asserted. Setting the INT_DISABLE bit to a 1 has no effect on
the state of this bit. This bit has been defined as part of the PCI Local Bus Specification
(Revision 2.3).
2-0
RSVD
Submit Documentation Feedback
R
Reserved. Bits 3-0 return 0h when read.
1394 OHCI PCI Configuration Space
117
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7.5
www.ti.com
Class Code and Revision ID Registers
The class code and revision ID registers categorize the 1394b OHCI controller as a serial bus controller
(0Ch), controlling an IEEE Std 1394 bus (00h), with an OHCI programming model (10h). Furthermore, the
TI chip revision is indicated in the least significant byte. See Table 7-4 for a complete description of the
register contents.
PCI register offset:
08h
Register type:
Read only
Default value:
0C00 1001h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
1
27
1
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
1
Table 7-4. Class Code and Revision ID Registers Description
BIT
FIELD NAME
ACCESS
DESCRIPTION
31-24
BASECLASS
R
Base class. This field returns 0Ch when read, which broadly classifies the function as a
serial bus controller.
23-16
SUBCLASS
R
Subclass. This field returns 00h when read, which specifically classifies the function as
controlling an IEEE Std 1394 serial bus.
15-8
PGMIF
R
Programming interface. This field returns 10h when read, which indicates that the
programming model is compliant with the 1394 Open Host Controller Interface
Specification.
7-0
CHIPREV
R
Silicon revision. This field returns 00h when read, which indicates the silicon revision of the
1394b OHCI controller.
7.6
Cache Line Size and Latency Timer Registers
The latency timer and class cache line size registers are programmed by the host BIOS to indicate system
cache-line size and the latency timer are associated with the 1394b OHCI controller. See Table 7-5 for a
complete description of the register contents.
PCI register offset:
0Ch
Register type:
Read/Write
Default value:
BIT NUMBER
RESET STATE
15
0
0000h
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 7-5. Latency Timer and Class Cache Line Size Registers Description
ACCESS
DESCRIPTION
15-8
BIT
LATENCY_TIMER
RW
PCI latency timer. The value in this register specifies the latency timer for the 1394b OHCI
controller, in units of PCI clock cycles. When the 1394b OHCI function is a PCI bus
initiator and asserts PCI_FRAME, the latency timer begins counting from zero. If the
latency timer expires before the 1394b OHCI functions transaction has terminated, the
1394b OHCI function terminates the transaction when its PCI_GNT is deasserted.
7-0
CACHELINE_SZ
RW
Cache-line size. This value is used by the OHCI controller during memory write and
invalidate, memory-read line, and memory-read multiple transactions. The default value for
this field is 00h.
118
FIELD NAME
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
7.7
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Header Type and BIST Registers
The header type and built-in self-test (BIST) registers indicate the OHCI controller PCI header type and no
built-in self-test. See Table 7-6 for a complete description of the register contents.
PCI register offset:
0Eh
Register type:
Read only
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 7-6. Header Type and BIST Registers Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15-8
BIST
R
Built-in self-test. The OHCI controller does not include a BIST; therefore, this field returns
00h when read.
7-0
HEADER_TYPE
R
PCI header type. The OHCI controller includes the standard PCI header, which is
communicated by returning 00h when this field is read. Since the 1394b OHCI core is
implemented as a single-function PCI device, bit 7 of this register must be 0b.
7.8
OHCI Base Address Register
The OHCI base address register is programmed with a base address referencing the memory-mapped
OHCI control. When the BIOS writes all 1s to this register, the value read back is FFFF F800h, indicating
that at least 2K bytes of memory address space are required for the OHCI registers. See Table 7-7 for a
complete description of the register contents.
PCI register offset:
10h
Register type:
Read/Write, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 7-7. OHCI Base Address Register Description
BIT
FIELD NAME
31-11
OHCIREG_PTR
10-4
3
2-1
0
TYPE
DESCRIPTION
RW
OHCI register pointer. This field specifies the upper 21 bits of the 32-bit OHCI base
address register. The default value for this field is all 0s.
OHCI_SZ
R
OHCI register size. This field returns 000 0000b when read, indicating that the OHCI
registers require a 2K-byte region of memory.
OHCI_PF
R
OHCI register prefetch. Bit 3 returns 0b when read, indicating that the OHCI registers are
nonprefetchable.
OHCI_MEMTYPE
R
OHCI memory type. This field returns 00b when read, indicating that the OHCI base
address register is 32 bits wide and mapping can be done anywhere in the 32-bit memory
space.
OHCI_MEM
R
OHCI memory indicator. Bit 0 returns 0b when read, indicating that the OHCI registers are
mapped into system memory space.
Submit Documentation Feedback
1394 OHCI PCI Configuration Space
119
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7.9
www.ti.com
TI Extension Base Address Register
The TI extension base address register is programmed with a base address referencing the
memory-mapped TI extension registers. When the BIOS writes all 1s to this register, the value read back
is FFFF C000h, indicating that at least 16K bytes of memory address space are required for the TI
registers. See Table 7-8 for a complete description of the register contents.
PCI register offset:
14h
Register type:
Read/Write, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 7-8. TI Base Address Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-14
TIREG_PTR
13-4
TI_SZ
R
TI register size. This field returns 00 0000 0000b when read, indicating that the TI registers
require a 16K-byte region of memory.
3
TI_PF
R
TI register prefetch. Bit 3 returns 0b when read, indicating that the TI registers are
nonprefetchable.
TI_MEMTYPE
R
TI memory type. This field returns 00b when read, indicating that the TI base address
register is 32 bits wide and mapping can be done anywhere in the 32-bit memory space.
TI_MEM
R
TI memory indicator. Bit 0 returns 0b when read, indicating that the TI registers are
mapped into system memory space.
2-1
0
RW
TI register pointer. This field specifies the upper 18 bits of the 32-bit TI base address
register. The default value for this field is all 0s.
7.10 CIS Base Address Register
The CARDBUS input to the 1394 OHCI core is tied high such that this register returns 0000 0000h when
read.
PCI register offset:
18h
Register type:
Read only
Default value:
120
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7.11 CIS Pointer Register
The CARDBUS input to the 1394 OHCI core is tied high such that this register returns 0000 0000h when
read.
PCI register offset:
28h
Register type:
Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
7.12 Subsystem Vendor ID and Subsystem ID Registers
The subsystem vendor ID and subsystem ID registers are used for system and option card identification
purposes. These registers can be initialized from the serial EEPROM or programmed via the subsystem
access register at offset F8h in the PCI configuration space (see Section 7.23). See Table 7-9 for a
complete description of the register contents.
PCI register offset:
2Ch
Register type:
Read/Update
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 7-9. Subsystem Vendor ID and Subsystem ID Registers Description
BIT
31-16 (1)
15-0(1)
(1)
FIELD NAME
TYPE
DESCRIPTION
OHCI_SSID
RU
Subsystem device ID. This field indicates the subsystem device ID.
OHCI_SSVID
RU
Subsystem vendor ID. This field indicates the subsystem vendor ID.
These bits are reset by PERST or FRST.
Submit Documentation Feedback
1394 OHCI PCI Configuration Space
121
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
7.13 Power Management Capabilities Pointer Register
The power management capabilities pointer register provides a pointer into the PCI configuration header
where the power-management register block resides. The OHCI controller configuration header double
words at offsets 44h and 48h provide the power-management registers. This register is read only and
returns 44h when read.
PCI register offset:
34h
Register type:
Read only
Default value:
44h
BIT NUMBER
RESET STATE
7
0
6
1
5
0
4
0
3
0
2
1
1
0
0
0
7.14 Interrupt Line and Interrupt Pin Registers
The interrupt line and interrupt pin registers communicate interrupt line routing information. See Table 7-10
for a complete description of the register contents.
PCI register offset:
3Ch
Register type:
Read/Write
Default value:
01FFh
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
1
7
1
6
1
5
1
4
1
3
1
2
1
1
1
0
1
Table 7-10. Interrupt Line and Interrupt Pin Registers Description
BIT
FIELD NAME
TYPE
15-8
INTR_PIN
R
7-0
INTR_LINE
RW
122
DESCRIPTION
Interrupt pin. This field returns 01h when read, indicating that the 1394 OHCI core signals
interrupts on the INTA terminal.
Interrupt line. This field is programmed by the system and indicates to software which interrupt
line the OHCI controller INTA is connected to. The default value for this field is all FFh, indicating
that an interrupt line has not yet been assigned to the function.
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7.15 Minimum Grant and Minimum Latency Registers
The minimum grant and minimum latency registers communicate to the system the desired setting of bits
15–8 in the latency timer and class cache line size register at offset 0Ch in the PCI configuration space
(see Section 7.6). If a serial EEPROM is detected, the contents of these registers are loaded through the
serial EEPROM interface. If no serial EEPROM is detected, these registers return a default value that
corresponds to the MAX_LAT = 4, MIN_GNT = 2. See Table 7-11 for a complete description of the
register contents.
PCI register offset:
3Eh
Register type:
Read/Update
Default value:
0402h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
1
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
1
0
0
Table 7-11. Minimum Grant and Minimum Latency Registers Description
BIT
15-8
FIELD NAME
(1)
7-0(1)
(1)
TYPE
DESCRIPTION
MAX_LAT
RU
Maximum latency. The contents of this field may be used by the host BIOS to assign an
arbitration priority level to the OHCI controller. The default for this register indicates that the
OHCI controller may access the PCI bus as often as every 0.25 s; thus, an extremely high
priority level is requested. Bits 11-8 of this field may also be loaded through the serial EEPROM.
MIN_GNT
RU
Minimum grant. The contents of this field may be used by the host BIOS to assign a latency timer
register value to the OHCI controller. The default for this register indicates that the OHCI
controller may sustain burst transfers for nearly 64 s and, thus, request a large value be
programmed in bits 15-8 of the OHCI controller latency timer and class cache line size register at
offset 0Ch in the PCI configuration space (see Section 7.6). Bits 3-0 of this field may also be
loaded through the serial EEPROM.
These bits are reset by PERST or FRST.
7.16 OHCI Control Register
The PCI OHCI control register is defined by the 1394 Open Host Controller Interface Specification and
provides a bit for big endian PCI support. See Table 7-12 for a complete description of the register
contents.
PCI register offset:
40h
Register type:
Read/Write, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 7-12. OHCI Control Register Description
BIT
31-1
0
FIELD NAME
RSVD
GLOBAL_SWAP
TYPE
R
RW
Submit Documentation Feedback
DESCRIPTION
Reserved. Bits 31-1 return 000 0000 0000 0000 0000 0000 0000 0000b when read.
When bit 0 is set to 1b, all quadlets read from and written to the PCI interface are byte swapped (big
endian). The default value for this bit is 0b, which is little endian mode.
1394 OHCI PCI Configuration Space
123
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
7.17 Capability ID and Next Item Pointer Registers
The capability ID and next item pointer registers identify the linked-list capability item and provide a pointer
to the next capability item. See Table 7-13 for a complete description of the register contents.
PCI register offset:
44h
Register type:
Read only
Default value:
0001h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
1
Table 7-13. Capability ID and Next Item Pointer Registers Description
BIT
FIELD NAME
TYPE
DESCRIPTION
15-8
NEXT_ITEM
R
Next item pointer. The OHCI controller supports only one additional capability that is communicated
to the system through the extended capabilities list; therefore, this field returns 00h when read.
7-0
CAPABILITY_ID
R
Capability identification. This field returns 01h when read, which is the unique ID assigned by the
PCI SIG for PCI power-management capability.
7.18 Power Management Capabilities Register
The power management capabilities register indicates the capabilities of the OHCI core related to PCI
power management. See Table 7-14 for a complete description of the register contents.
PCI register offset:
46h
Register type:
Read only
Default value:
7E03h
BIT NUMBER
RESET STATE
15
0
14
1
13
1
12
1
11
1
10
1
9
1
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
1
0
1
Table 7-14. Power Management Capabilities Register Description
BIT
FIELD NAME
15-11 PME_SUPPORT
TYPE
DESCRIPTION
R
PME support. This 5-bit field indicates the power states from which the OHCI core may assert PME.
This field returns a value of 01111b, indicating that PME is asserted from the D3hot, D2, D1, and D0
power states.
10
D2_SUPPORT
R
D2 support. Bit 10 is hardwired to 1b, indicating that the OHCI controller supports the D2 power state.
9
D1_SUPPORT
R
D1 support. Bit 9 is hardwired to 1b, indicating that the OHCI controller supports the D1 power state.
AUX_CURRENT
R
Auxiliary current. This 3-bit field reports the 3.3-VAUX auxiliary current requirements. This field returns
000b, because the 1394a core is not powered by VAUX.
5
DSI
R
Device-specific initialization. This bit returns 0b when read, indicating that the OHCI controller does
not require special initialization beyond the standard PCI configuration header before a generic class
driver is able to use it.
4
RSVD
R
Reserved. Bit 4 returns 0b when read.
3
PME_CLK
R
PME clock. This bit returns 0b when read, indicating that no host bus clock is required for the OHCI
controller to generate PME.
PM_VERSION
R
Power-management version. If bit 7 (PCI_PM_VERSION_CTRL) in the PCI miscellaneous
configuration register at offset F0h (see Section 7.21) is 0b, this field returns 010b indicating Revision
1.1 compatibility. If PCI_PM_VERSION_CTRL in the PCI miscellaneous configuration register is 1b,
this field returns 011b indicating Revision 1.2 compatibility.
8-6
2-0
124
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
7.19 Power Management Control and Status Register
The power management control and status register implements the control and status of the PCI
power-management function. This register is not affected by the internally-generated reset caused by the
transition from the D3hot to D0 state. See Table 7-15 for a complete description of the register contents.
PCI register offset:
48h
Register type:
Read/Write, Read only
Default value:
0000h
BIT NUMBER
RESET STATE
15
0
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 7-15. Power Management Control and Status Register Description
BIT
FIELD NAME
15
TYPE
DESCRIPTION
PME_STS
R
PME status. This bit returns 0b, because PME is not supported.
14-13
DATA_SCALE
R
This field returns 00b, because the data register is not implemented.
12-9
DATA_SELECT
R
This field returns 0h, because the data register is not implemented.
PME_ENB
R
This bit returns 0b, because PME is not supported.
R
Reserved. Bits 7-2 return 00 0000b when read.
8
7-2
RSVD
1-0 (1)
PWR_STATE
RW
Power state. This 2-bit field sets the 1394b OHCI controller power state and is encoded
as:
00
01
10
11
(1)
=
=
=
=
Current
Current
Current
Current
power
power
power
power
state
state
state
state
is D0 (default).
is D1.
is D2.
is D3.
These bits are reset on the rising edge of PRST.
7.20 Power Management Extension Registers
The power management extension registers provide extended power-management features not applicable
to the OHCI controller; thus, they are read only and returns 0000h when read. See Table 7-16 for a
complete description of the register contents.
PCI register offset:
4Ah
Register type:
Read only
Default value:
BIT NUMBER
RESET STATE
15
0
0000h
14
0
13
0
12
0
11
0
10
0
9
0
8
0
7
0
6
0
5
0
4
0
3
0
2
0
1
0
0
0
Table 7-16. Power Management Extension Registers Description
BIT
15-0
FIELD NAME
RSVD
TYPE
R
DESCRIPTION
Reserved. Bits 15-0 return 0000h when read.
7.21 PCI Miscellaneous Configuration Register
The PCI miscellaneous configuration register provides miscellaneous PCI-related configuration. See
Table 7-17 for a complete description of the register contents.
PCI register offset:
F0h
Register type:
Read/Write, Read only
Default value:
0000 0A90h
Submit Documentation Feedback
1394 OHCI PCI Configuration Space
125
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
(1)
126
www.ti.com
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7 (1)
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
1
0
1
0
1
0
0
1
0
0
0
0
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 7-17. PCI Miscellaneous Configuration Register
BIT
31-16
15
14-12
FIELD NAME
TYPE
DESCRIPTION
RSVD
R
Reserved. Bits 31-16 return 0000h when read.
PME_D3COLD
R
PME support from D3cold. The 1394a OHCI core does not support PME generation from
D3cold. Therefore, this bit is tied to 0b.
RSVD
R
Reserved. Bits 14-12 return 000b when read.
11
PCI2_3_EN
R
PCI 2.3 enable. The 1394 OHCI core always conforms to the PCI 2.3 specification;
therefore, this bit is tied to 1b.
10
10 IGNORE_
MSTRINT_
ENA_FOR_PME
RW
IGNORE_MSTRINT_ENA_FOR_PME bit for PME generation. When set, this bit causes bit
26 of the OHCI vendor ID register (OHCI offset 40h, see Section 8.15) to read 1b.
Otherwise, bit 26 reads 0b.
0 = PME behavior generated from unmasked interrupt bits and
IntMask.masterIntEnable bit (default)
1 = PME generation does not depend on the value of IntMask.masterIntEnable.
9-8
(1)
MR_ENHANCE
RW
This field selects the read command behavior of the PCI master for read transactions of
greater than two data phases. For read transactions of one or two data phases, a memory
read command is used.
00
01
10
11
7(1)
PCI_PM_
VERSION_CTRL
RW
=
=
=
=
Memory read line
Memory read
Memory read multiple (default)
Reserved, behavior reverts to default
PCI power-management version control. This bit controls the value reported in the Version
field of the power management capabilities register of the 1394 OHCI function.
0 = Version fields report 010b for Power Management 1.1 compliance.
1 = Version fields report 011b for Power Management 1.2 compliance (default).
6-5
RSVD
4(1)
DIS_TGT_ABT
R
RW
Reserved. Bits 6-5 return 00b when read.
Disable target abort. Bit 4 controls the no-target-abort mode, in which the OHCI controller
returns indeterminate data instead of signaling target abort. The OHCI LLC is divided into
the PCLK and SCLK domains. If software tries to access registers in the link that are not
active because the SCLK is disabled, a target abort is issued by the link. On some
systems, this can cause a problem resulting in a fatal system error. Enabling this bit allows
the link to respond to these types of requests by returning FFh.
0 = Responds with OHCI-Lynx compatible target abort.
1 = Responds with indeterminate data equal to FFh. It is recommended that this bit
be set to 1b (default).
3(1)
SB_EN
RW
Serial bus enable. In the bridge, the serial bus interface is controlled using the bridge
configuration registers. Therefore, this bit has no effect in the 1394b OHCI function. The
default value for this bit is 0b.
2(1)
DISABLE_
SCLKGATE
RW
Disable SCLK test feature. This bit controls locking or unlocking the SCLK to the 1394a
OHCI core PCI bus clock input. This is a test feature only and must be cleared to 0b (all
applications).
0 = Hardware decides auto-gating of the PHY clock (default).
1 = Disables auto-gating of the PHY clock
1(1)
DISABLE_
PCIGATE
RW
Disable PCLK test feature. This bit controls locking or unlocking the PCI clock to the 1394a
OHCI core PCI bus clock input. This is a test feature only and must be cleared to 0b (all
applications).
0 = Hardware decides auto-gating of the PCI clock (default).
1 = Disables auto-gating of the PCI clock
0(1)
(1)
KEEP_PCLK
RW
Keep PCI clock running. This bit controls the PCI clock operation during the CLKRUN
protocol. Since the CLKRUN protocol is not supported in the XIO2200, this bit has no
effect. The default value for this bit is 0b.
These bits are reset by PERST, GRST, or the internally-generated power-on reset.
Submit Documentation Feedback
1394 OHCI PCI Configuration Space
127
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
7.22 Link Enhancement Control Register
The link enhancement control register implements TI proprietary bits that are initialized by software or by a
serial EEPROM, if present. After these bits are set to 1b, their functionality is enabled only if bit 22
(aPhyEnhanceEnable) in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2,
Host Controller Control Register) is set to 1. See Table 7-18 for a complete description of the register
contents.
128
PCI register offset:
F4h
Register type:
Read/Write, Read only
Default value:
0000 4000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 7-18. Link Enhancement Control Register Description
BIT
FIELD NAME
TYPE
RSVD
15(1)
dis_at_pipeline
RW
Disable AT pipelining. When bit 15 is set to 1b, out-of-order AT pipelining is disabled. The
default value for this bit is 0b.
14(1)
ENAB_DRAFT
RW
Enable OHCI 1.2 draft features. When this bit is set, it enables some features beyond the
OHCI 1.1 specification. Specifically, this enables HCControl.LPS to be cleared by writing a 1
to the HCControlClear.LPS bit and enables the link to set bit 9 in the xfer status field of AR
and IR context control registers. This bit can be initialized from an attached EEPROM.
atx_thresh
RW
This field sets the initial AT threshold value, which is used until the AT FIFO is underrun.
When the OHCI controller retries the packet, it uses a 4K-byte threshold, resulting in a
store-and-forward operation.
13-12(1)
R
DESCRIPTION
31-16
Reserved. Bits 31-16 return 0000h when read.
00
01
10
11
=
=
=
=
Threshold
Threshold
Threshold
Threshold
~4K bytes resulting in a store-and-forward operation (default)
~1.7K bytes
~1K bytes
~512 bytes
These bits fine tune the asynchronous transmit threshold. For most applications, the
1.7K-byte threshold is optimal. Changing this value may increase or decrease the 1394
latency depending on the average PCI bus latency.
Setting the AT threshold to 1.7K, 1K, or 512 bytes results in data being transmitted at these
thresholds or when an entire packet has been checked into the FIFO. If the packet to be
transmitted is larger than the AT threshold, the remaining data must be received before the
AT FIFO is emptied; otherwise, an underrun condition occurs, resulting in a packet error at
the receiving node. As a result, the link then commences store-and-forward operation. Wait
until it has the complete packet in the FIFO before retransmitting it on the second attempt to
ensure delivery.
An AT threshold of 4K results in store-and-forward operation, which means that asynchronous
data is not transmitted until an end-of-packet token is received. Restated, setting the AT
threshold to 4K results in only complete packets being transmitted.
Note that the OHCI controller will always use store-and-forward when the asynchronous
transmit retries register at OHCI offset 08h (see Section 8.3, Asynchronous Transmit Retries
Register) is cleared.
11
(1)
10
9
RSVD
enab_mpeg_ts
RSVD
R
RW
R
Reserved. Bit 11 returns 0b when read.
Enable MPEG CIP timestamp enhancement. When bit 9 is set to 1b, the enhancement is
enabled for MPEG CIP transmit streams (FMT = 20h). The default value for this bit is 0b.
Reserved. Bit 9 returns 0b when read.
8(1)
enab_dv_ts
RW
Enable DV CIP timestamp enhancement. When bit 8 is set to 1b, the enhancement is enabled
for DV CIP transmit streams (FMT = 00h). The default value for this bit is 0b.
7(1)
enab_unfair
RW
Enable asynchronous priority requests (OHCI-Lynx compatible). Setting bit 7 to 1b enables
the link to respond to requests with priority arbitration. It is recommended that this bit be set to
1b. The default value for this bit is 0b.
6-3
RSVD
R
2(1)
RSVD
RW
Reserved. Bit 2 defaults to 0b and must remain 0b for normal operation of the OHCI core.
1(1)
enab_accel
RW
Enable acceleration enhancements (OHCI-Lynx compatible). When bit 1 is set to 1b, the PHY
is notified that the link supports the IEEE Std 1394a-2000 acceleration enhancements, that is,
ack-accelerated, fly-by concatenation, etc. It is recommended that this bit be set to 1b. The
default value for this bit is 0b.
0(1)
RSVD
Submit Documentation Feedback
R
Reserved. Bits 6-3 return 0h when read.
Reserved. Bit 0 returns 0b when read.
1394 OHCI PCI Configuration Space
129
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
7.23 Subsystem Access Register
Write access to the subsystem access register identically updates the subsystem ID registers to
OHCI-Lynx. The system ID value written to this register may also be read back from this register. See
Table 7-19 for a complete description of the register contents.
PCI register offset:
F8h
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 7-19. Subsystem Access Register Description
BIT
31-16
FIELD NAME
(1)
15-0(1)
(1)
130
TYPE
DESCRIPTION
SUBDEV_ID
RW
Subsystem device ID alias. This field indicates the subsystem device ID.
SUBVEN_ID
RW
Subsystem vendor ID alias. This field indicates the subsystem vendor ID.
These bits shall only be reset by a fundamental reset (FRST). FRST is asserted (low) whenever PERST or GRST is asserted.
1394 OHCI PCI Configuration Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
8
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
1394 OHCI Memory-Mapped Register Space
The OHCI registers defined by the 1394 Open Host Controller Interface Specification are memory mapped
into a 2K-byte region of memory pointed to by the OHCI base address register at offset 10h in PCI
configuration space (see Section 7.8). These registers are the primary interface for controlling the IEEE
Std 1394 link function.
This section provides the register interface and bit descriptions. Several set/clear register pairs in this
programming model are implemented to solve various issues with typical read-modify-write control
registers. There are two addresses for a set/clear register — RegisterSet and RegisterClear (see
Table 8-1 for register listing). A 1 bit written to RegisterSet causes the corresponding bit in the set/clear
register to be set to 1b; a 0 bit leaves the corresponding bit unaffected. A 1 bit written to RegisterClear
causes the corresponding bit in the set/clear register to be cleared; a 0 bit leaves the corresponding bit in
the set/clear register unaffected.
Typically, a read from either RegisterSet or RegisterClear returns the contents of the set or clear register,
respectively. However, sometimes reading the RegisterClear provides a masked version of the set or clear
register. The interrupt event register is an example of this behavior.
Table 8-1. OHCI Register Map
DMA CONTEXT
REGISTER NAME
ABBREVIATION
OHCI version
Version
00h
GUID ROM
GUID_ROM
04h
Asynchronous transmit retries
ATRetries
08h
CSR data
CSRData
0Ch
CSR compare
CSRCompareData
10h
CSR control
CSRControl
14h
Configuration ROM header
ConfigROMhdr
18h
Bus identification
BusID
1Ch
Bus options (1)
BusOptions
20h
GUID high(1)
GUIDHi
24h
(1)
GUID low
GUIDLo
Reserved(1)
Configuration ROM mapping
ConfigROMmap
34h
Posted write address low
PostedWriteAddressLo
38h
Posted write address high
PostedWriteAddressHi
3Ch
Vendor ID
VendorID
Host controller control (1)
HCControlSet
Reserved
54h
60h
Self-ID buffer pointer
SelfIDBuffer
Self-ID count
SelfIDCount
Reserved
Isochronous receive channel mask low
50h
58h-5Ch
Reserved
Isochronous receive channel mask high
40h
44h-4Ch
HCControlClr
(1)
28h
2Ch-30h
Reserved
Self-ID
OFFSET
64h
68h
6Ch
IRChannelMaskHiSet
70h
IRChannelMaskHiClear
74h
IRChannelMaskLoSet
78h
IRChannelMaskLoClear
7Ch
One or more bits in this register are reset by PERST or FRST.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
131
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 8-1. OHCI Register Map (continued)
DMA CONTEXT
REGISTER NAME
Interrupt event
Interrupt mask
Isochronous transmit interrupt event
Isochronous transmit interrupt mask
Isochronous receive interrupt event
Isochronous receive interrupt mask
ABBREVIATION
80h
IntEventClear
84h
IntMaskSet
88h
IntMaskClear
8Ch
IsoXmitIntEventSet
90h
IsoXmitIntEventClear
94h
IsoXmitIntMaskSet
98h
IsoXmitIntMaskClear
9Ch
IsoRecvIntEventSet
A0h
IsoRecvIntEventClear
A4h
IsoRecvIntMaskSet
A8h
IsoRecvIntMaskClear
ACh
Initial bandwidth available
InitialBandwidthAvailable
B0h
Initial channels available high
InitialChannelsAvailableHi
B4h
Initial channels available low
InitialChannelsAvailableLo
B8h
Reserved
BCh-D8h
Fairness control
FairnessControl
DCh
Link control (1)
LinkControlSet
E0h
LinkControlClear
E4h
Node identification
NodeID
E8h
PHY control
PhyControl
ECh
Isochronous cycle timer
Isocyctimer
F0h
Reserved
Asynchronous request filter high
Asynchronous request filter low
Physical request filter high
Physical request filter low
Physical upper bound
F4h-FCh
AsyncRequestFilterHiSet
100h
AsyncRequestFilterHiClear
104h
AsyncRequestFilterLoSet
108h
AsyncRequestFilterLoClear
10Ch
PhysicalRequestFilterHiSet
110h
PhysicalRequestFilterHiClear
114h
PhysicalRequestFilterLoSet
118h
PhysicalRequestFilterLoClear
11Ch
PhysicalUpperBound
120h
Reserved
Asynchronous Request
Transmit
(ATRQ)
Asynchronous context control
124h-17Ch
ContextControlSet
180h
ContextControlClear
184h
CommandPtr
18Ch
Reserved
Asynchronous context command pointer
188h
Reserved
Asynchronous Response
Transmit
(ATRS)
Asynchronous context control
190h-19Ch
ContextControlSet
1A0h
ContextControlClear
1A4h
CommandPtr
1ACh
Reserved
Asynchronous context command pointer
Reserved
132
OFFSET
IntEventSet
1394 OHCI Memory-Mapped Register Space
1A8h
1B0h-1BCh
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-1. OHCI Register Map (continued)
DMA CONTEXT
Asynchronous Request
Receive
(ARRQ)
REGISTER NAME
Asynchronous context control
ABBREVIATION
1C0h
ContextControlClear
1C4h
CommandPtr
1CCh
Reserved
Asynchronous context command pointer
1C8h
Reserved
Asynchronous Response
Receive
(ARRS)
Asynchronous context control
1D0h-1DCh
ContextControlSet
1E0h
ContextControlClear
1E4h
CommandPtr
1ECh
Reserved
Asynchronous context command pointer
1E8h
Reserved
Isochronous Transmit
Context n
n = 0, 1, 2, 3, ..., 7
Isochronous transmit context control
1F0h-1FCh
ContextControlSet
200h + 16*n
ContextControlClear
204h + 16*n
CommandPtr
20Ch + 16*n
Reserved
Isochronous transmit context command pointer
208h + 16*n
Reserved
Isochronous Receive
Context n
n = 0, 1, 2, 3
Isochronous receive context control
OFFSET
ContextControlSet
210h-3FCh
ContextControlSet
400h + 32*n
ContextControlClear
404h + 32*n
Isochronous receive context command pointer
CommandPtr
40Ch + 32*n
Isochronous receive context match
ContextMatch
410h + 32*n
Reserved
Submit Documentation Feedback
408h + 32*n
1394 OHCI Memory-Mapped Register Space
133
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.1
www.ti.com
OHCI Version Register
The OHCI version register indicates the OHCI version support and whether or not the serial EEPROM is
present. See Table 8-2 for a complete description of the register contents.
OHCI register offset:
00h
Register type:
Read only
Default value:
0X01 0010h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
X
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
1
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
Table 8-2. OHCI Version Register Description
BIT
FIELD NAME
TYPE
31-25
RSVD
24 (1)
GUID_ROM
23-16
version
R
Major version of the OHCI. The controller is compliant with the 1394 Open Host Controller Interface
Specification, Release 1.2; thus, this field reads 01h.
15-8
RSVD
R
Reserved. Bits 15-8 return 00h when read.
7-0
revision
R
Minor version of the OHCI. The controller is compliant with the 1394 Open Host Controller Interface
Specification, Release 1.2; thus, this field reads 10h.
(1)
134
R
DESCRIPTION
RU
Reserved. Bits 31-25 return 000 0000b when read.
The controller sets bit 24 to 1b if the serial EEPROM is detected. If the serial EEPROM is present, the
Bus_Info_Block is automatically loaded on system (hardware) reset. The default value for this bit is 0b.
One or more bits in this register are reset by PERST or FRST.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
8.2
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
GUID ROM Register
The GUID ROM register accesses the serial EEPROM, and is only applicable if bit 24 (GUID_ROM) in the
OHCI version register at OHCI offset 00h (see Section 8.1) is set to 1b. See Table 8-3 for a complete
description of the register contents.
OHCI register offset:
04h
Register type:
Read/Set/Update, Read/Update, Read only
Default value:
00XX 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-3. GUID ROM Register Description
BIT
31
FIELD NAME
addrReset
TYPE
RSU
30-26
RSVD
R
25
rdStart
RSU
DESCRIPTION
Software sets bit 31 to 1b to reset the GUID ROM address to 0. When the controller
completes the reset, it clears this bit. The controller does not automatically fill bits 23-16
(rdData field) with the 0 byte.
Reserved. Bits 30-26 return 00 0000b when read.
A read of the currently addressed byte is started when bit 25 is set to 1b. This bit is
automatically cleared when the controller completes the read of the currently addressed
GUID ROM byte.
24
RSVD
R
23-16
rdData
RU
15-8
RSVD
R
Reserved. Bits 15-8 return 00h when read.
7-0
miniROM
R
The miniROM field defaults to 00h indicating that no miniROM is implemented. If an
EEPROM is implemented, all eight bits of this miniROM field are downloaded from
EEPROM word offset 28h. For this device, the miniROM field must be greater than 39h to
indicate a valid miniROM offset into the EEPROM.
Submit Documentation Feedback
Reserved. Bit 24 returns 0b when read.
This field contains the data read from the GUID ROM.
1394 OHCI Memory-Mapped Register Space
135
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.3
www.ti.com
Asynchronous Transmit Retries Register
The asynchronous transmit retries register indicates the number of times the controller attempts a retry for
asynchronous DMA request transmit and for asynchronous physical and DMA response transmit. See
Table 8-4 for a complete description of the register contents.
OHCI register offset:
08h
Register type:
Read/Write, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-4. Asynchronous Transmit Retries Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-29
secondLimit
R
The second limit field returns 000b when read, because outbound dual-phase retry is not
implemented.
28-16
cycleLimit
R
The cycle limit field returns 0 0000 0000 0000b when read, because outbound
dual-phase retry is not implemented.
15-12
RSVD
R
Reserved. Bits 15-12 return 0h when read.
11-8
maxPhysRespRetries
RW
This field tells the physical response unit how many times to attempt to retry the transmit
operation for the response packet when a busy acknowledge or ack_data_error is
received from the target node. The default value for this field is 0h.
7-4
maxATRespRetries
RW
This field tells the asynchronous transmit response unit how many times to attempt to
retry the transmit operation for the response packet when a busy acknowledge or
ack_data_error is received from the target node. The default value for this field is 0h.
3-0
maxATReqRetries
RW
This field tells the asynchronous transmit DMA request unit how many times to attempt
to retry the transmit operation for the response packet when a busy acknowledge or
ack_data_error is received from the target node. The default value for this field is 0h.
8.4
CSR Data Register
The CSR data register accesses the bus-management CSR registers from the host through
compare-swap operations. This register contains the data to be stored in a CSR if the compare is
successful.
OHCI register offset:
0Ch
Register type:
Read only
Default value:
136
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1394 OHCI Memory-Mapped Register Space
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
8.5
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
CSR Compare Register
The CSR compare register accesses the bus-management CSR registers from the host through
compare-swap operations. This register contains the data to be compared with the existing value of the
CSR resource.
OHCI register offset:
10h
Register type:
Read only
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
8.6
CSR Control Register
The CSR control register accesses the bus-management CSR registers from the host through
compare-swap operations. This register controls the compare-swap operation and selects the CSR
resource. See Table 8-5 for a complete description of the register contents.
OHCI register offset:
14h
Register type:
Read/Write, Read/Update, Read only
Default value:
8000 000Xh
BIT NUMBER
RESET STATE
31
1
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
X
X
Table 8-5. CSR Control Register Description
BIT
31
FIELD NAME
csrDpme
TYPE
RU
32-2
RSVD
R
1-0
csrSel
RW
DESCRIPTION
Bit 31 is set to 1b by the controller when a compare-swap operation is complete. It is
cleared whenever this register is written.
Reserved. Bits 30-2 return 0 0000 0000 0000 0000 0000 0000 0000b when read.
This field selects the CSR resource as follows:
00
01
10
11
Submit Documentation Feedback
=
=
=
=
BUS_MANAGER_ID
BANDWIDTH_AVAILABLE
CHANNELS_AVAILABLE_HI
CHANNELS_AVAILABLE_LO
1394 OHCI Memory-Mapped Register Space
137
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.7
www.ti.com
Configuration ROM Header Register
The configuration ROM header register externally maps to the first quadlet of the 1394 configuration ROM,
offset FFFF F000 0400h. See Table 8-6 for a complete description of the register contents.
OHCI register offset:
18h
Register type:
Read/Write
Default value:
0000 XXXXh
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-6. Configuration ROM Header Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-24
info_length
RW
Information length. IEEE Std 1394 bus-management field. Must be valid when bit 17
(linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2)
is set to 1b. The default value for this field is 0h.
23-16
crc_length
RW
CRC length. IEEE Std 1394 bus-management field. Must be valid when bit 17 (linkEnable) in
the host controller control register at OHCI offset 50h/54h (see Section 3.3.2) is set to 1b.
The default value for this field is 0h.
15-0
rom_crc_value
RW
ROM CRC value. IEEE Std 1394 bus-management field. Must be valid at any time bit 17
(linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2)
is set to 1b.
8.8
Bus Identification Register
The bus identification register externally maps to the first quadlet in the Bus_Info_Block and contains the
constant 3133 3934h, which is the ASCII value of 1394.
OHCI register offset:
1Ch
Register type:
Read only
Default value:
138
3133 3934h
BIT NUMBER
RESET STATE
31
0
30
0
29
1
28
1
27
0
26
0
25
0
24
1
23
0
22
0
21
1
20
1
19
0
18
0
17
1
16
1
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
1
1
1
0
0
1
0
0
1
1
0
1
0
0
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
8.9
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Bus Options Register
The bus options register externally maps to the second quadlet of the Bus_Info_Block. See Table 8-7 for a
complete description of the register contents.
OHCI register offset:
20h
Register type:
Read/Write, Read only
Default value:
0000 B0X3h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
1
0
1
1
0
0
0
0
X
X
0
0
0
0
1
1
Table 8-7. Bus Options Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
irmc
RW
Isochronous resource-manager capable. IEEE Std 1394 bus-management field. Must be valid when
bit 17 (linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2)
is set to 1b. The default value for this bit is 0b.
30
cmc
RW
Cycle master capable. IEEE Std 1394 bus-management field. Must be valid when bit 17 (linkEnable)
in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2) is set to 1b. The
default value for this bit is 0b.
29
isc
RW
Isochronous support capable. IEEE Std 1394 bus-management field. Must be valid when bit 17
(linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2) is set
to 1b. The default value for this bit is 0b.
28
bmc
RW
Bus manager capable. IEEE Std 1394 bus-management field. Must be valid when bit 17
(linkEnable) in the host controller control register at OHCI offset 50h/54h (see Section 3.3.2) is set
to 1b. The default value for this bit is 0b.
27
pmc
RW
Power-management capable. IEEE Std 1394 bus-management field. When bit 27 is set to 1b, this
indicates that the node is power-management capable. Must be valid when bit 17 (linkEnable) in the
host controller control register at OHCI offset 50h/54h (see Section 3.3.2) is set to 1b. The default
value for this bit is 0b.
26-24
RSVD
23-16
cyc_clk_acc
15-12 (1) max_rec
R
Reserved. Bits 26-24 return 000b when read.
RW
Cycle master clock accuracy (in parts per million). IEEE Std 1394 bus-management field. Must be
valid when bit 17 (linkEnable) in the host controller control register at OHCI offset 50h/54h (see
Section 3.3.2) is set to 1b. The default value for this field is 00h.
RW
Maximum request. IEEE Std 1394 bus-management field. Hardware initializes this field to indicate
the maximum number of bytes in a block request packet that is supported by the implementation.
This value, max_rec_bytes, must be 512 or greater, and is calculated by 2^(max_rec + 1). Software
may change this field; however, this field must be valid at any time bit 17 (linkEnable) in the host
controller control register at OHCI offset 50h/54h (see Section 3.3.2) is set to 1b. A received block
write request packet with a length greater than max_rec_bytes may generate an ack_type_error.
This field is not affected by a software reset, and defaults to value indicating 4096 bytes on a
system (hardware) reset. The default value for this field is Bh.
11-8
RSVD
7-6
g
5-3
RSVD
R
Reserved. Bits 5-3 return 000b when read.
2-0
Lnk_spd
R
Link speed. This field returns 011b, indicating that the link speeds of 100M bit/s, 200M bit/s, 400M
bit/s, and 800M bit/s are supported.
(1)
R
RW
Reserved. Bits 11-8 return 0h when read.
Generation counter. This field is incremented if any portion of the configuration ROM has been
incremented since the prior bus reset.
These bits are reset by PERST or FRST.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
139
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.10 GUID High Register
The GUID high register represents the upper quadlet in a 64-bit global unique ID (GUID), which maps to
the third quadlet in the Bus_Info_Block. This register contains node_vendor_ID and chip_ID_hi fields. This
register initializes to 0000 0000h on a system (hardware) reset, which is an illegal GUID value. If a serial
EEPROM is detected, the contents of this register are loaded through the serial EEPROM interface. At
that point, the contents of this register cannot be changed. If no serial EEPROM is detected, the contents
of this register are loaded by the BIOS. At that point, the contents of this register cannot be changed. This
register is reset by a PCIe reset (PERST), GRST, or the internally-generated power-on reset.
(1)
OHCI register offset:
24h
Register type:
Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3 (1)
2 (1)
1 (1)
0 (1)
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
These bits are reset only by a global reset (GRST) or the internally generated power-on reset.
8.11 GUID Low Register
The GUID low register represents the lower quadlet in a 64-bit global unique ID (GUID), which maps to
chip_ID_lo in the Bus_Info_Block. This register initializes to 0000 0000h on a system (hardware) reset and
behaves identical to the GUID high register at OHCI offset 24h (see Section 8.10). This register is reset by
PERST, GRST, or the internally-generated power-on reset.
(1)
140
OHCI register offset:
28h
Register type:
Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3 (1)
2 (1)
1 (1)
0 (1)
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
These bits are reset only by a global reset (GRST) or the internally generated power-on reset.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.12 Configuration ROM Mapping Register
The configuration ROM mapping register contains the start address within system memory that maps to
the start address of 1394 configuration ROM for this node. See Table 8-8 for a complete description of the
register contents.
OHCI register offset::
34h
Register type:
Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-8. Configuration ROM Mapping Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-10
configROMaddr
RW
Configuration ROM address. If a quadlet read request to 1394 offset FFFF F000 0400h through
offset FFFF F000 07FFh is received, the low-order ten bits of the offset are added to this register to
determine the host memory address of the read request. The default value for this field is all 0s.
9-0
RSVD
R
Reserved. Bits 9-0 return 00 0000 0000b when read.
8.13 Posted Write Address Low Register
The posted write address low register communicates error information if a write request is posted and an
error occurs while the posted data packet is being written. See Table 8-9 for a complete description of the
register contents.
OHCI register offset:
38h
Register type:
Read/Update
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-9. Posted Write Address Low Register Description
BIT
31-0
FIELD NAME
offsetLo
Submit Documentation Feedback
TYPE
RU
DESCRIPTION
Offset low. The lower 32 bits of the 1394 destination offset of the write request that failed.
1394 OHCI Memory-Mapped Register Space
141
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.14 Posted Write Address High Register
The posted write address high register communicates error information if a write request is posted and an
error occurs while writing the posted data packet. See Table 8-10 for a complete description of the register
contents.
OHCI register offset:
3Ch
Register type:
Read/Update
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-10. Posted Write Address High Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-16
sourceID
RU
Source identification. This field is the 10-bit bus number (bits 31-22) and 6-bit node number
(bits 21-16) of the node that issued the write request that failed.
15-0
offsetHi
RU
Offset high. The upper 16 bits of the 1394 destination offset of the write request that failed.
8.15 Vendor ID Register
The vendor ID register holds the company ID of an organization that specifies any vendor-unique
registers. The controller implements TI unique behavior with regards to OHCI. Thus, this register is read
only and returns 0x08 0028h when read.
OHCI register offset:
40h
Register type:
Read only
Default value:
0x08 0028h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
x
25
x
24
1
23
0
22
0
21
0
20
0
19
1
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
8.16 Host Controller Control Register
The host controller control set/clear register pair provides flags for controlling the controller. See
Table 8-11 for a complete description of the register contents.
142
OHCI register offset:
50h set register
54h clear register
Register type:
Read/Set/Clear/Update, Read/Set/Clear, Read/Clear, Read only
Default value:
0080 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
1
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-11. Host Controller Control Register Description
BIT
31
FIELD NAME
BIBimageValid
TYPE
DESCRIPTION
RSU
When bit 31 is set to 1b, the physical response unit is enabled to respond to block read requests
to host configuration ROM and to the mechanism for atomically updating configuration ROM.
Software creates a valid image of the bus_info_block in host configuration ROM before setting this
bit.
When this bit is cleared, the controller returns ack_type_error on block read requests to host
configuration ROM. Also, when this bit is cleared and a 1394 bus reset occurs, the configuration
ROM mapping register at OHCI offset 34h (see Section 8.12), configuration ROM header register
at OHCI offset 18h (see Section 8.7), and bus options register at OHCI offset 20h (see
Section 8.9) are not updated.
Software can set this bit only when bit 17 (linkEnable) is 0b. Once bit 31 is set to 1b, it can be
cleared by a system (hardware) reset, a software reset, or if a fetch error occurs when the
controller loads bus_info_block registers from host memory.
30
noByteSwapData
RSC
Bit 30 controls whether physical accesses to locations outside the controller itself, as well as any
other DMA data accesses are byte swapped.
29
ack_Tardy_enable
RSC
Bit 29 controls the acknowledgement of ack_tardy. When bit 29 is set to 1b, ack_tardy may be
returned as an acknowledgment to accesses from the 1394 bus to the controller, including
accesses to the bus_info_block. The controller returns ack_tardy to all other asynchronous
packets addressed to the node. When the controller sends ack_tardy, bit 27 (ack_tardy) in the
interrupt event register at OHCI offset 80h/84h (see Section 8.21) is set to 1b to indicate the
attempted asynchronous access.
Software ensures that bit 27 (ack_tardy) in the interrupt event register is 0b. Software also
unmasks wake-up interrupt events such as bit 19 (phy) and bit 27 (ack_tardy) in the interrupt
event register before placing the controller into the D1 power mode.
Software must not set this bit if the node is the 1394 bus manager.
28-24
RSVD
23 (1)
programPhyEnable
RC
Bit 23 informs upper-level software that lower-level software has consistently configured the IEEE
Std 1394a-2000 enhancements in the link and PHYs. When this bit is 1b, generic software such
as the OHCI driver is responsible for configuring IEEE Std 1394a-2000 enhancements in the PHY
and bit 22 (aPhyEnhanceEnable). When this bit is 0b, the generic software may not modify the
IEEE Std 1394a-2000 enhancements in the PHY and cannot interpret the setting of bit 22
(aPhyEnhanceEnable). This bit is initialized from serial EEPROM.
22
aPhyEnhanceEnabl
e
RSC
When bits 23 (programPhyEnable) and 17 (linkEnable) are 11b, the OHCI driver can set bit 22 to
1b to use all IEEE Std 1394a-2000 enhancements. When bit 23 (programPhyEnable) is cleared to
0b, the software does not change PHY enhancements or this bit.
21-20
19
R
RSVD
R
LPS
RSC
Reserved. Bits 28-24 return 00000b when read.
Reserved. Bits 21 and 20 return 00b when read.
Bit 19 controls the link power status. Software must set this bit to 1b to permit the link-PHY
communication. A 0b prevents link-PHY communication.
The OHCI link is divided into two clock domains (PCLK and PHY_SCLK). If software tries to
access any register in the PHY_SCLK domain while the PHY_SCLK is disabled, a target abort is
issued by the link. This problem can be avoided by setting bit 4 (DIS_TGT_ABT) to 1b in the PCI
miscellaneous configuration register at offset F0h in the PCI configuration space (see
Section 7.21). This allows the link to respond to these types of request by returning all Fs (hex).
OHCI registers at offsets DCh-F0h and 100h-11Ch are in the PHY_SCLK domain.
After setting LPS, software must wait approximately 10 ms before attempting to access any of the
OHCI registers. This gives the PHY_SCLK time to stabilize.
18
postedWriteEnable
RSC
Bit 18 enables (1) or disables (0) posted writes. Software changes this bit only when bit 17
(linkEnable) is 0b.
17
linkEnable
RSC
Bit 17 is cleared to 0b by either a system (hardware) or software reset. Software must set this bit
to 1b when the system is ready to begin operation and then force a bus reset. This bit is
necessary to keep other nodes from sending transactions before the local system is ready. When
this bit is cleared, the controller is logically and immediately disconnected from the 1394 bus, no
packets are received or processed, nor are packets transmitted.
16
SoftReset
RSCU
When bit 16 is set to 1b, all states are reset, all FIFOs are flushed, and all OHCI registers are set
to their system (hardware) reset values, unless otherwise specified. PCI registers are not affected
by this bit. This bit remains set to 1b while the software reset is in progress and reverts back to 0b
when the reset has completed.
15-0
(1)
RSVD
R
Reserved. Bits 15-0 return 0000h when read.
This bit is reset by PERST or FRST.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
143
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.17 Self-ID Buffer Pointer Register
The self-ID buffer pointer register points to the 2K-byte-aligned base address of the buffer in host memory
where the self-ID packets are stored during bus initialization. Bits 31-11 are read/write accessible. Bits
10-0 are reserved and return 000 0000 0000b when read.
OHCI register offset:
64h
Register type:
Read/Write, Read only
Default value:
XXXX XX00h
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
8.18 Self-ID Count Register
The self-ID count register keeps a count of the number of times the bus self-ID process has occurred,
flags self-ID packet errors, and keeps a count of the self-ID data in the self-ID buffer. See Table 8-12 for a
complete description of the register contents.
OHCI register offset:
68h
Register type:
Read/Update, Read only
Default value:
X0XX 0000h
BIT NUMBER
RESET STATE
31
X
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-12. Self-ID Count Register Description
BIT
31
FIELD NAME
selfIDError
30-24
RSVD
23-16
selfIDGeneration
15-11
RSVD
10-2
selfIDSize
1-0
RSVD
144
TYPE
Description
RU
Self-ID error. When bit 31 is set to 1b, an error was detected during the most recent self-ID
packet reception. The contents of the self-ID buffer are undefined. This bit is cleared after a
self-ID reception in which no errors are detected. Note that an error can be a hardware error or
a host bus write error.
R
RU
R
RU
R
Reserved. Bits 30-24 return 000 0000b when read.
Self-ID generation. The value in this field increments each time a bus reset is detected. This
field rolls over to 0 after reaching 255.
Reserved. Bits 15-11 return 00000b when read.
Self-ID size. This field indicates the number of quadlets that have been written into the self-ID
buffer for the current bits 23-16 (selfIDGeneration field). This includes the header quadlet and
the self-ID data. This field is cleared to 0 0000 0000b when the self-ID reception begins.
Reserved. Bits 1 and 0 return 00b when read.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.19 Isochronous Receive Channel Mask High Register
The isochronous receive channel mask high set/clear register enables packet receives from the upper 32
isochronous data channels. A read from either the set or clear register returns the content of the
isochronous receive channel mask high register. See Table 8-13 for a complete description of the register
contents.
OHCI register offset:
70h set register
74h clear register
Register type:
Read/Set/Clear
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-13. Isochronous Receive Channel Mask High Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
isoChannel63
RSC
When bit 31 is set to 1b, the controller is enabled to receive from isochronous channel number 63.
30
isoChannel62
RSC
When bit 30 is set to 1b, the controller is enabled to receive from isochronous channel number 62.
29
isoChannel61
RSC
When bit 29 is set to 1b, the controller is enabled to receive from isochronous channel number 61.
28
isoChannel60
RSC
When bit 28 is set to 1b, the controller is enabled to receive from isochronous channel number 60.
27
isoChannel59
RSC
When bit 27 is set to 1b, the controller is enabled to receive from isochronous channel number 59.
26
isoChannel58
RSC
When bit 26 is set to 1b, the controller is enabled to receive from isochronous channel number 58.
25
isoChannel57
RSC
When bit 25 is set to 1b, the controller is enabled to receive from isochronous channel number 57.
24
isoChannel56
RSC
When bit 24 is set to 1b, the controller is enabled to receive from isochronous channel number 56.
23
isoChannel55
RSC
When bit 23 is set to 1b, the controller is enabled to receive from isochronous channel number 55.
22
isoChannel54
RSC
When bit 22 is set to 1b, the controller is enabled to receive from isochronous channel number 54.
21
isoChannel53
RSC
When bit 21 is set to 1b, the controller is enabled to receive from isochronous channel number 53.
20
isoChannel52
RSC
When bit 20 is set to 1b, the controller is enabled to receive from isochronous channel number 52.
19
isoChannel51
RSC
When bit 19 is set to 1b, the controller is enabled to receive from isochronous channel number 51.
18
isoChannel50
RSC
When bit 18 is set to 1b, the controller is enabled to receive from isochronous channel number 50.
17
isoChannel49
RSC
When bit 17 is set to 1b, the controller is enabled to receive from isochronous channel number 49.
16
isoChannel48
RSC
When bit 16 is set to 1b, the controller is enabled to receive from isochronous channel number 48.
15
isoChannel47
RSC
When bit 15 is set to 1b, the controller is enabled to receive from isochronous channel number 47.
14
isoChannel46
RSC
When bit 14 is set to 1b, the controller is enabled to receive from isochronous channel number 46.
13
isoChannel45
RSC
When bit 13 is set to 1b, the controller is enabled to receive from isochronous channel number 45.
12
isoChannel44
RSC
When bit 12 is set to 1b, the controller is enabled to receive from isochronous channel number 44.
11
isoChannel43
RSC
When bit 11 is set to 1b, the controller is enabled to receive from isochronous channel number 43.
10
isoChannel42
RSC
When bit 10 is set to 1b, the controller is enabled to receive from isochronous channel number 42.
9
isoChannel41
RSC
When bit 9 is set to 1b, the controller is enabled to receive from isochronous channel number 41.
8
isoChannel40
RSC
When bit 8 is set to 1b, the controller is enabled to receive from isochronous channel number 40.
7
isoChannel39
RSC
When bit 7 is set to 1b, the controller is enabled to receive from isochronous channel number 39.
6
isoChannel38
RSC
When bit 6 is set to 1b, the controller is enabled to receive from isochronous channel number 38.
5
isoChannel37
RSC
When bit 5 is set to 1b, the controller is enabled to receive from isochronous channel number 37.
4
isoChannel36
RSC
When bit 4 is set to 1b, the controller is enabled to receive from isochronous channel number 36.
3
isoChannel35
RSC
When bit 3 is set to 1b, the controller is enabled to receive from isochronous channel number 35.
2
isoChannel34
RSC
When bit 2 is set to 1b, the controller is enabled to receive from isochronous channel number 34.
1
isoChannel33
RSC
When bit 1 is set to 1b, the controller is enabled to receive from isochronous channel number 33.
0
isoChannel32
RSC
When bit 0 is set to 1b, the controller is enabled to receive from isochronous channel number 32.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
145
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.20 Isochronous Receive Channel Mask Low Register
The isochronous receive channel mask low set/clear register enables packet receives from the lower 32
isochronous data channels. See Table 8-14 for a complete description of the register contents.
OHCI register offset:
78h set register
7Ch clear register
Register type:
Read/Set/Clear
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-14. Isochronous Receive Channel Mask Low Register Description
BIT
FIELD NAME
TYPE
Description
31
isoChannel31
RSC
When bit 31 is set to 1b, the controller is enabled to receive from isochronous channel number 31.
30
isoChannel30
RSC
When bit 30 is set to 1b, the controller is enabled to receive from isochronous channel number 30.
29-2
isoChanneln
RSC
Bits 29-2 (isoChanneln, where n = 29, 28, 27, ..., 2) follow the same pattern as bits 31 and 30.
1
isoChannel1
RSC
When bit 1 is set to 1b, the controller is enabled to receive from isochronous channel number 1.
0
isoChannel0
RSC
When bit 0 is set to 1b, the controller is enabled to receive from isochronous channel number 0.
8.21 Interrupt Event Register
The interrupt event set/clear register reflects the state of the various interrupt sources. The interrupt bits
are set to 1b by an asserting edge of the corresponding interrupt signal or by writing a 1b in the
corresponding bit in the set register. The only mechanism to clear a bit in this register is to write a 1b to
the corresponding bit in the clear register.
This register is fully compliant with the 1394 Open Host Controller Interface Specification, and the
controller adds a vendor-specific interrupt function to bit 30. When the interrupt event register is read, the
return value is the bit-wise AND function of the interrupt event and interrupt mask registers. See
Table 8-15 for a complete description of the register contents.
OHCI register offset:
146
80h
set register
84h
clear register [returns the content of the interrupt event register
bit-wise ANDed with the interrupt mask register when read]
Register type:
Read/Set/Clear/Update, Read/Set/Clear, Read/Update, Read
only
Default value:
XXXX 0XXXh
BIT NUMBER
RESET STATE
31
0
30
X
29
0
28
0
27
0
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
0
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X
X
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-15. Interrupt Event Register Description
BIT
FIELD NAME
TYPE
R
DESCRIPTION
31
RSVD
30
vendorSpecific
RSC
This vendor-specific interrupt event is reported when either of the general-purpose interrupts
are asserted. The general-purpose interrupts are enabled by setting the corresponding bits
INT_3EN and INT_2EN (bits 31 and 23, respectively) to 1 in the GPIO control register at offset
FCh in the PCI configuration space.
29
SoftInterrupt
RSC
Bit 29 is used by software to generate an interrupt for its own use.
28
RSVD
27
ack_tardy
R
RSCU
Reserved. Bit 31returns 0b when read.
Reserved. Bit 28 returns 0b when read.
Bit 27 is set to 1b when bit 29 (AckTardyEnable) in the host controller control register at OHCI
offset 50h/54h (see Section 3.3.2) is set to 1b and any of the following conditions occur:
a. Data is present in a receive FIFO that is to be delivered to the host.
b. The physical response unit is busy processing requests or sending responses.
c. The controller sent an ack_tardy acknowledgment.
26
phyRegRcvd
RSCU
The controller has received a PHY register data byte that can be read from bits 23-16 in the
PHY control register at OHCI offset ECh (see Section 8.33).
25
cycleTooLong
RSCU
If bit 21 (cycleMaster) in the link control register at OHCI offset E0h/E4h (see Section 8.30) is
set to 1b, this indicates that over 125 s has elapsed between the start of sending a cycle start
packet and the end of a subaction gap. Bit 21 (cycleMaster) in the link control register is
cleared by this event.
24
unrecoverableError
RSCU
This event occurs when the controller encounters any error that forces it to stop operations on
any or all of its subunits, for example, when a DMA context sets its dead bit to 1b. While bit 24
is set to 1b, all normal interrupts for the context(s) that caused this interrupt are blocked from
being set to 1b.
23
cycleInconsistent
RSCU
A cycle start was received that had values for the cycleSeconds and cycleCount fields that are
different from the values in bits 31-25 (cycleSeconds field) and bits 24-12 (cycleCount field) in
the isochronous cycle timer register at OHCI offset F0h (see Section 8.34).
22
cycleLost
RSCU
A lost cycle is indicated when no cycle_start packet is sent or received between two
successive cycleSynch events. A lost cycle can be predicted when a cycle_start packet does
not immediately follow the first subaction gap after the cycleSynch event or if an arbitration
reset gap is detected after a cycleSynch event without an intervening cycle start. Bit 22 may
be set to 1b either when a lost cycle occurs or when logic predicts that one will occur.
21
cycle64Seconds
RSCU
Indicates that the seventh bit of the cycle second counter has changed
20
cycleSynch
RSCU
Indicates that a new isochronous cycle has started. Bit 20 is set to 1b when the low-order bit
of the cycle count toggles.
19
phy
RSCU
Indicates that the PHY requests an interrupt through a status transfer
18
regAccessFail
RSCU
Indicates that a register access has failed due to a missing SCLK clock signal from the PHY.
When a register access fails, bit 18 is set to 1b before the next register access.
17
busReset
RSCU
Indicates that the PHY has entered bus reset mode
16
selfIDcomplete
RSCU
A self-ID packet stream has been received. It is generated at the end of the bus initialization
process. Bit 16 is turned off simultaneously when bit 17 (busReset) is turned on.
15
selfIDcomplete2
RSCU
Secondary indication of the end of a self-ID packet stream. Bit 15 is set to 1b by the controller
when it sets bit 16 (selfIDcomplete), and retains the state, independent of bit 17 (busReset).
14-10
RSVD
R
Reserved. Bits 14-10 return 00000b when read.
9
lockRespErr
RSCU
Indicates that the controller sent a lock response for a lock request to a serial bus register, but
did not receive an ack_complete
8
postedWriteErr
RSCU
Indicates that a host bus error occurred while the controller was trying to write a 1394 write
request, which had already been given an ack_complete, into system memory
7
isochRx
RU
Isochronous receive DMA interrupt. Indicates that one or more isochronous receive contexts
have generated an interrupt. This is not a latched event; it is the logical OR of all bits in the
isochronous receive interrupt event register at OHCI offset A0h/A4h (see Section 8.25) and
isochronous receive interrupt mask register at OHCI offset A8h/ACh (see Section 8.26). The
isochronous receive interrupt event register indicates which contexts have been interrupted.
6
isochTx
RU
Isochronous transmit DMA interrupt. Indicates that one or more isochronous transmit contexts
have generated an interrupt. This is not a latched event; it is the logical OR of all bits in the
isochronous transmit interrupt event register at OHCI offset 90h/94h (see Section 8.23) and
isochronous transmit interrupt mask register at OHCI offset 98h/9Ch (see Section 8.24). The
isochronous transmit interrupt event register indicates which contexts have been interrupted.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
147
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 8-15. Interrupt Event Register Description (continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
5
RSPkt
RSCU
Indicates that a packet was sent to an asynchronous receive response context buffer and the
descriptor xferStatus and resCount fields have been updated
4
RQPkt
RSCU
Indicates that a packet was sent to an asynchronous receive request context buffer and the
descriptor xferStatus and resCount fields have been updated
3
ARRS
RSCU
Asynchronous receive response DMA interrupt. Bit 3 is conditionally set to 1b upon completion
of an ARRS DMA context command descriptor.
2
ARRQ
RSCU
Asynchronous receive request DMA interrupt. Bit 2 is conditionally set to 1b upon completion
of an ARRQ DMA context command descriptor.
1
respTxComplete
RSCU
Asynchronous response transmit DMA interrupt. Bit 1 is conditionally set to 1b upon
completion of an ATRS DMA command.
0
reqTxCompleter
RSCU
Asynchronous request transmit DMA interrupt. Bit 0 is conditionally set to 1b upon completion
of an ATRQ DMA command.
8.22 Interrupt Mask Register
The interrupt mask set/clear register enables the various interrupt sources. Reads from either the set
register or the clear register always return the contents of the interrupt mask register. In all cases except
masterIntEnable (bit 31) and vendorSpecific (bit 30), the enables for each interrupt event align with the
interrupt event register bits detailed in Table 8-15.
This register is fully compliant with the 1394 Open Host Controller Interface Specification, and the
controller adds an interrupt function to bit 30. See Table 8-16 for a complete description of bits 31 and 30.
OHCI register offset:
88h set register
8Ch clear register
Register type:
Read/Set/Clear/Update, Read/Set/Clear, Read/Update, Read
only
Default value:
XXXX 0XXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
0
28
0
27
0
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
0
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
X
X
X
X
X
X
X
X
X
X
Table 8-16. Interrupt Mask Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
masterIntEnable
RSCU
30
VendorSpecific
RSC
When this bit and bit 30 (vendorSpecific) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this vendor-specific interrupt mask enables interrupt
generation.
29
SoftInterrupt
RSC
When this bit and bit 29 (SoftInterrupt) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this soft-interrupt mask enables interrupt generation.
28
RSVD
27
ack_tardy
RSC
When this bit and bit 27 (ack_tardy) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this acknowledge-tardy interrupt mask enables interrupt
generation.
26
phyRegRcvd
RSC
When this bit and bit 26 (phyRegRcvd) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this PHY register interrupt mask enables interrupt
generation.
25
cycleTooLong
RSC
When this bit and bit 25 (cycleTooLong) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this cycle-too-long interrupt mask enables interrupt
generation.
148
R
Master interrupt enable. If bit 31 is set to 1b, external interrupts are generated in accordance
with the interrupt mask register. If this bit is cleared, external interrupts are not generated,
regardless of the interrupt mask register settings.
Reserved. Bit 28 returns 0b when read.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-16. Interrupt Mask Register Description (continued)
BIT
FIELD NAME
TYPE
DESCRIPTION
24
unrecoverableError
RSC
When this bit and bit 24 (unrecoverableError) in the interrupt event register at OHCI offset
80h/84h (see Section 8.21) are set to 11b, this unrecoverable-error interrupt mask enables
interrupt generation.
23
cycleInconsistent
RSC
When this bit and bit 23 (cycleInconsistent) in the interrupt event register at OHCI offset
80h/84h (see Section 8.21) are set to 11b, this inconsistent-cycle interrupt mask enables
interrupt generation.
22
cycleLost
RSC
When this bit and bit 22 (cycleLost) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this lost-cycle interrupt mask enables interrupt generation.
21
cycle64Seconds
RSC
When this bit and bit 21 (cycle64Seconds) in the interrupt event register at OHCI offset
80h/84h (see Section 8.21) are set to 11b, this 64-s cycle interrupt mask enables interrupt
generation.
20
cycleSynch
RSC
When this bit and bit 20 (cycleSynch) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this isochronous-cycle interrupt mask enables interrupt
generation.
19
phy
RSC
When this bit and bit 19 (phy) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this PHY-status-transfer interrupt mask enables interrupt
generation.
18
regAccessFail
RSC
When this bit and bit 18 (regAccessFail) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this register-access-failed interrupt mask enables interrupt
generation.
17
busReset
RSC
When this bit and bit 17 (busReset) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this bus-reset interrupt mask enables interrupt generation.
16
selfIDcomplete
RSC
When this bit and bit 16 (selfIDcomplete) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this self-ID-complete interrupt mask enables interrupt
generation.
15
selfIDcomplete2
RSC
When this bit and bit 15 (selfIDcomplete2) in the interrupt event register at OHCI offset
80h/84h (see Section 8.21) are set to 11b, this second self-ID-complete interrupt mask
enables interrupt generation.
14-10
RSVD
R
Reserved. Bits 14-10 return 00000b when read.
9
lockRespErr
RSC
When this bit and bit 9 (lockRespErr) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this lock-response-error interrupt mask enables interrupt
generation.
8
postedWriteErr
RSC
When this bit and bit 8 (postedWriteErr) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this posted-write-error interrupt mask enables interrupt
generation.
7
isochRx
RSC
When this bit and bit 7 (isochRx) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this isochronous-receive-DMA interrupt mask enables interrupt
generation.
6
isochTx
RSC
When this bit and bit 6 (isochTx) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this isochronous-transmit-DMA interrupt mask enables interrupt
generation.
5
RSPkt
RSC
When this bit and bit 5 (RSPkt) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this receive-response-packet interrupt mask enables interrupt
generation.
4
RQPkt
RSC
When this bit and bit 4 (RQPkt) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this receive-request-packet interrupt mask enables interrupt
generation.
3
ARRS
RSC
When this bit and bit 3 (ARRS) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this asynchronous-receive-response-DMA interrupt mask enables
interrupt generation.
2
ARRQ
RSC
When this bit and bit 2 (ARRQ) in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21) are set to 11b, this asynchronous-receive-request-DMA interrupt mask enables
interrupt generation.
1
respTxComplete
RSC
When this bit and bit 1 (respTxComplete) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this response-transmit-complete interrupt mask enables
interrupt generation.
0
reqTxComplete
RSC
When this bit and bit 0 (reqTxComplete) in the interrupt event register at OHCI offset 80h/84h
(see Section 8.21) are set to 11b, this request-transmit-complete interrupt mask enables
interrupt generation.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
149
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.23 Isochronous Transmit Interrupt Event Register
The isochronous transmit interrupt event set/clear register reflects the interrupt state of the isochronous
transmit contexts. An interrupt is generated on behalf of an isochronous transmit context if an
OUTPUT_LAST* command completes and its interrupt bits are set to 1. Upon determining that the
isochTx (bit 6) interrupt has occurred in the interrupt event register at OHCI offset 80h/84h (see
Section 8.21), software can check this register to determine which context caused the interrupt. The
interrupt bits are set to 1 by an asserting edge of the corresponding interrupt signal, or by writing a 1b in
the corresponding bit in the set register. The only mechanism to clear a bit in this register is to write a 1b
to the corresponding bit in the clear register. See Table 8-17 for a complete description of the register
contents.
OHCI register
offset:
90h set register
94h clear register (returns the contents of the isochronous transmit interrupt
event register bit-wise ANDed with the isochronous transmit interrupt
mask register when read)
Register type:
Read/Set/Clear, Read only
Default value:
0000 00XXh
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Table 8-17. Isochronous Transmit Interrupt Event Register Description
BIT
31-8
150
FIELD NAME
RSVD
TYPE
R
DESCRIPTION
Reserved. Bits 31-8 return 0000h when read.
7
isoXmit7
RSC
Isochronous transmit context 7 caused the interrupt event register bit 6 (isochTx) interrupt.
6
isoXmit6
RSC
Isochronous transmit context 6 caused the interrupt event register bit 6 (isochTx) interrupt.
5
isoXmit5
RSC
Isochronous transmit context 5 caused the interrupt event register bit 6 (isochTx) interrupt.
4
isoXmit4
RSC
Isochronous transmit context 4 caused the interrupt event register bit 6 (isochTx) interrupt.
3
isoXmit3
RSC
Isochronous transmit context 3 caused the interrupt event register bit 6 (isochTx) interrupt.
2
isoXmit2
RSC
Isochronous transmit context 2 caused the interrupt event register bit 6 (isochTx) interrupt.
1
isoXmit1
RSC
Isochronous transmit context 1 caused the interrupt event register bit 6 (isochTx) interrupt.
0
isoXmit0
RSC
Isochronous transmit context 0 caused the interrupt event register bit 6 (isochTx) interrupt.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.24 Isochronous Transmit Interrupt Mask Register
The isochronous transmit interrupt mask set/clear register enables the isochTx interrupt source on a
per-channel basis. Reads from either the set register or the clear register always return the contents of the
isochronous transmit interrupt mask register. In all cases, the enables for each interrupt event align with
the isochronous transmit interrupt event register bits detailed in Table 8-17.
OHCI register offset:
98h set register
9Ch clear register
Register type:
Read/Set/Clear, Read only
Default value:
0000 00XX
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
8.25 Isochronous Receive Interrupt Event Register
The isochronous receive interrupt event set/clear register reflects the interrupt state of the isochronous
receive contexts. An interrupt is generated on behalf of an isochronous receive context if an INPUT_*
command completes and its interrupt bits are set to 1. Upon determining that the isochRx (bit 7) interrupt
in the interrupt event register at OHCI offset 80h/84h (see Section 8.21) has occurred, software can check
this register to determine which context(s) caused the interrupt. The interrupt bits are set to 1 by an
asserting edge of the corresponding interrupt signal or by writing a 1b in the corresponding bit in the set
register. The only mechanism to clear a bit in this register is to write a 1b to the corresponding bit in the
clear register. See Table 8-18 for a complete description of the register contents.
OHCI register
offset:
A0h
set register
A4h
clear register (returns the contents of isochronous receive interrupt
event register bit-wise ANDed with the isochronous receive mask
register when read)
Register type:
Read/Set/Clear, Read only
Default value:
0000 000Xh
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
X
X
X
X
Table 8-18. Isochronous Receive Interrupt Event Register Description
BIT
31-4
FIELD NAME
TYPE
RSVD
R
Description
Reserved. Bits 31-4 return 000 0000h when read.
3
isoRecv3
RSC
Isochronous receive channel 3 caused the interrupt event register bit 7 (isochRx) interrupt.
2
isoRecv2
RSC
Isochronous receive channel 2 caused the interrupt event register bit 7 (isochRx) interrupt.
1
isoRecv1
RSC
Isochronous receive channel 1 caused the interrupt event register bit 7 (isochRx) interrupt.
0
isoRecv0
RSC
Isochronous receive channel 0 caused the interrupt event register bit 7 (isochRx) interrupt.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
151
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.26 Isochronous Receive Interrupt Mask Register
The isochronous receive interrupt mask set/clear register enables the isochRx interrupt source on a
per-channel basis. Reads from either the set register or the clear register always return the contents of the
isochronous receive interrupt mask register. In all cases, the enables for each interrupt event align with
the isochronous receive interrupt event register bits detailed in Table 8-18.
OHCI register offset:
A8h set register
ACh clear register
Register type:
Read/Set/Clear, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
8.27 Initial Bandwidth Available Register
The initial bandwidth available register value is loaded into the corresponding bus-management CSR
register on a system (hardware) or software reset. See Table 8-19 for a complete description of the
register contents.
OHCI register offset:
B0h
Register type:
Read only, Read/Write
Default value:
0000 1333h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
1
0
0
1
1
0
0
1
1
0
0
1
1
Table 8-19. Initial Bandwidth Available Register Description
BIT
FIELD NAME
31-13
RSVD
12-0
InitBWAvailable
152
TYPE
R
RW
DESCRIPTION
Reserved. Bits 31-13 return 000 0000 0000 0000 0000b when read.
This field is reset to 1333h on a system (hardware) or software reset, and is not affected by a
1394 bus reset. The value of this field is loaded into the BANDWIDTH_AVAILABLE CSR
register upon a GRST, PERST, PRST, or 1394 bus reset.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.28 Initial Channels Available High Register
The initial channels available high register value is loaded into the corresponding bus-management CSR
register on a system (hardware) or software reset. See Table 8-20 for a complete description of the
register contents.
OHCI register offset:
B4h
Register type:
Read/Write
Default value:
FFFF FFFFh
BIT NUMBER
RESET STATE
31
1
30
1
29
1
28
1
27
1
26
1
25
1
24
1
23
1
22
1
21
1
20
1
19
1
18
1
17
1
16
1
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Table 8-20. Initial Channels Available High Register Description
BIT
FIELD NAME
TYPE
31-0
InitChanAvailHi
RW
Description
This field is reset to FFFF_FFFFh on a system (hardware) or software reset, and is not affected by
a 1394 bus reset. The value of this field is loaded into the CHANNELS_AVAILABLE_HI CSR
register upon a GRST, PERST, PRST, or 1394 bus reset.
8.29 Initial Channels Available Low Register
The initial channels available low register value is loaded into the corresponding bus-management CSR
register on a system (hardware) or software reset. See Table 8-21 for complete description of the register
contents.
OHCI register offset:
B8h
Register type:
Read/Write
Default value:
FFFF FFFFh
BIT NUMBER
RESET STATE
31
1
30
1
29
1
28
1
27
1
26
1
25
1
24
1
23
1
22
1
21
1
20
1
19
1
18
1
17
1
16
1
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Table 8-21. Initial Channels Available Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-0
InitChanAvailLo
RW
This field is reset to FFFF_FFFFh on a system (hardware) or software reset, and is not affected by
a 1394 bus reset. The value of this field is loaded into the CHANNELS_AVAILABL_LO CSR register
upon a GRST, PRST, PRST, or 1394 bus reset.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
153
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.30 Fairness Control Register
The fairness control register provides a mechanism by which software can direct the host controller to
transmit multiple asynchronous requests during a fairness interval. See Table 8-22 for a complete
description of the register contents.
OHCI register offset:
DCh
Register type:
Read only, Read/Write
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-22. Fairness Control Registre Description
BIT
FIELD NAME
TYPE
31-8
RSVD
R
7-0
pri_req
RW
154
DESCRIPTION
Reserved. Bits 31-8 return 00 0000h when read.
Priority requests. This field specifies the maximum number of priority arbitration requests for
asynchronous request packets that the link is permitted to make of the PHY during a fairness
interval. The default value for this field is 00h.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.31 Link Control Register
The link control set/clear register provides the control flags that enable and configure the link core protocol
portions of the controller. It contains controls for the receiver and cycle timer. See Table 8-23 for a
complete description of the register contents.
OHCI register offset:
E0h set register
E4h clear register
Register type:
Read/Set/Clear/Update, Read/Set/Clear, Read only
Default value:
00X0 0X00h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
X
21
X
20
X
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
X
X
0
0
0
0
0
0
0
0
0
Table 8-23. Link Control Register Description
BIT
31-23
TYPE
RSVD
R
DESCRIPTION
Reserved. Bits 31-23 return 0 0000 0000b when read.
22
cycleSource
RSC
When bit 22 is set to 1b, the cycle timer uses an external source (CYCLEIN) to determine when to
roll over the cycle timer. When this bit is cleared, the cycle timer rolls over when the timer reaches
3072 cycles of the 24.576-MHz clock (125 s).
21
cycleMaster
RSCU
When bit 21 is set to 1b and the controller is root, it generates a cycle start packet every time the
cycle timer rolls over, based on the setting of bit 22 (cycleSource). When the controller is not root,
regardless of the setting of bit 21, the controller accepts received cycle start packets to maintain
synchronization with the node that is sending them. Bit 21 is automatically cleared when bit 25
(cycleTooLong) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21) is set to
1b. Bit 21 cannot be set to 1b until bit 25 (cycleTooLong) is cleared.
20
CycleTimerEnable
19-11
RSVD
RSC
R
When bit 20 is set to 1b, the cycle timer offset counts cycles of the 24.576-MHz clock and rolls
over at the appropriate time, based on the settings of the previous bits. When this bit is cleared,
the cycle timer offset does not count.
Reserved. Bits 19-11 return 0 0000 0000b when read.
10
RcvPhyPkt
RSC
When bit 10 is set to 1b, the receiver accepts incoming PHY packets into the AR request context
if the AR request context is enabled. This bit does not control receipt of self-ID packets.
9
RcvSelfID
RSC
When bit 9 is set to 1b, the receiver accepts incoming self-ID packets. Before setting this bit to 1b,
software must ensure that the self-ID buffer pointer register contains a valid address.
8-7
6
(1)
5-0
(1)
FIELD NAME
RSVD
tag1SyncFilterLock
RSVD
R
RS
R
Reserved. Bits 8 and 7 return 00b when read.
When bit 6 is set to 1b, bit 6 (tag1SyncFilter) in the isochronous receive context match register
(see Section 8.46) is set to 1b for all isochronous receive contexts. When bit 6 is cleared, bit 6
(tag1SyncFilter) in the isochronous receive context match register has read/write access.
Reserved. Bits 5-0 return 00 0000b when read.
This bit is reset by PERST or FRST.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
155
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.32 Node Identification Register
The node identification register contains the address of the node on which the OHCI-Lynx chip resides,
and indicates the valid node number status. The 16-bit combination of the busNumber field (bits 15-6) and
the NodeNumber field (bits 5-0) is referred to as the node ID. See Table 8-24 for a complete description of
the register contents.
OHCI register offset:
E8h
Register type:
Read/Write/Update, Read/Update, Read only
Default value:
0000 FFXXh
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
1
1
1
1
1
1
1
1
1
1
X
X
X
X
X
X
Table 8-24. Node Identification Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
IDValid
RU
Identification valid. Bit 31 indicates whether or not the controller has a valid node number. It is
cleared when a 1394 bus reset is detected and set to 1b when the controller receives a new node
number from its PHY.
30
root
RU
Root. Bit 30 is set to 1b during the bus reset process if the attached PHY is root.
29-28
27
RSVD
CPS
26-16
RSVD
15-6
busNumber
5-0
NodeNumber
156
R
RU
R
RWU
RU
Reserved. Bits 29 and 28 return 00b when read.
Cable power status. Bit 27 is set to 1b if the PHY is reporting that cable power status is OK.
Reserved. Bits 26-16 return 000 0000 0000b when read.
Bus number. This field identifies the specific 1394 bus the controller belongs to when multiple
1394-compatible buses are connected via a bridge. The default value for this field is all 1s.
Node number. This field is the physical node number established by the PHY during self
identification. It is automatically set to the value received from the PHY after the self-identification
phase. If the PHY sets the NodeNumber to 63, software must not set bit 15 (run) in the
asynchronous context control register (see Section 8.40) for either of the AT DMA contexts.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.33 PHY Control Register
The PHY control register reads from or writes to a PHY register. See Table 8-25 for a complete
description of the register contents.
OHCI register offset:
ECh
Register type:
Read/Write/Update, Read/Write, Read/Update, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-25. PHY Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
RU
Read done. Bit 31 is cleared to 0b by the controller when either bit 15 (rdReg) or bit 14 (wrReg) is set
to 1b. This bit is set to 1b when a register transfer is received from the PHY.
31
rdDone
30-28
RSVD
R
27-24
rdAddr
RU
Read address. This field is the address of the register most recently received from the PHY.
23-16
rdData
RU
Read data,\. This field is the contents of a PHY register that has been read.
15
rdReg
RWU
Read register. Bit 15 is set to 1b by software to initiate a read request to a PHY register, and is
cleared by hardware when the request has been sent. Bits 14 (wrReg) and 15 (rdReg) must not both
be set to 1b simultaneously.
14
wrReg
RWU
Write register. Bit 14 is set to 1b by software to initiate a write request to a PHY register, and is
cleared by hardware when the request has been sent. Bits 14 (wrReg) and 15 (rdReg) must not both
be set to 1b simultaneously.
13-12
RSVD
11.8
regAddr
RW
Register address. This field is the address of the PHY register to be written or read. The default value
for this field is 0h.
7.0
wrData
RW
Write data. This field is the data to be written to a PHY register and is ignored for reads. The default
value for this field is 00h.
R
Submit Documentation Feedback
Reserved. Bits 30-28 return 000b when read.
Reserved. Bits 13 and 12 return 00b when read.
1394 OHCI Memory-Mapped Register Space
157
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.34 Isochronous Cycle Timer Register
The isochronous cycle timer register indicates the current cycle number and offset. When the controller is
cycle master, this register is transmitted with the cycle start message. When the controller is not cycle
master, this register is loaded with the data field in an incoming cycle start. In the event that the cycle start
message is not received, the fields can continue incrementing on their own (if programmed) to maintain a
local time reference. See Table 8-26 for a complete description of the register contents.
OHCI register offset:
F0h
Register type:
Read/Write/Update
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-26. Isochronous Cycle Timer Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31-25
cycleSeconds
RWU
Cycle seconds. This field counts seconds [rollovers from bits 24-12 (cycleCount field)] modulo 128.
24-12
cycleCount
RWU
Cycle count. This field counts cycles [rollovers from bits 11-0 (cycleOffset field)] modulo 8000.
11-0
cycleOffset
RWU
Cycle offset. This field counts 24.576-MHz clocks modulo 3072, that is, 125 s. If an external 8-kHz
clock configuration is being used, this field must be cleared to 000h at each tick of the external clock.
8.35 Asynchronous Request Filter High Register
The asynchronous request filter high set/clear register enables asynchronous receive requests on a
per-node basis, and handles the upper node IDs. When a packet is destined for either the physical
request context or the ARRQ context, the source node ID is examined. If the bit corresponding to the node
ID is not set to 1b in this register, the packet is not acknowledged and the request is not queued. The
node ID comparison is done if the source node is on the same bus as the controller. Nonlocal bus-sourced
packets are not acknowledged unless bit 31 in this register is set to 1b. See Table 8-27 for a complete
description of the register contents.
158
OHCI register offset:
100h set register
104 h clear register
Register type:
Read/Set/Clear
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-27. Asynchronous Request Filter High Register Description
BIT
FIELD NAME
TYPE
31
asynReqAllBuses
RSC
If bit 31 is set to 1b, all asynchronous requests received by the controller from nonlocal bus nodes
are accepted.
30
asynReqResource62
RSC
If bit 30 is set to 1b for local bus node number 62, asynchronous requests received by the controller
from that node are accepted.
29
asynReqResource61
RSC
If bit 29 is set to 1b for local bus node number 61, asynchronous requests received by the controller
from that node are accepted.
28
asynReqResource60
RSC
If bit 28 is set to 1b for local bus node number 60, asynchronous requests received by the controller
from that node are accepted.
27
asynReqResource59
RSC
If bit 27 is set to 1b for local bus node number 59, asynchronous requests received by the controller
from that node are accepted.
26
asynReqResource58
RSC
If bit 26 is set to 1b for local bus node number 58, asynchronous requests received by the controller
from that node are accepted.
25
asynReqResource57
RSC
If bit 25 is set to 1b for local bus node number 57, asynchronous requests received by the controller
from that node are accepted.
24
asynReqResource56
RSC
If bit 24 is set to 1b for local bus node number 56, asynchronous requests received by the controller
from that node are accepted.
23
asynReqResource55
RSC
If bit 23 is set to 1b for local bus node number 55, asynchronous requests received by the controller
from that node are accepted.
22
asynReqResource54
RSC
If bit 22 is set to 1b for local bus node number 54, asynchronous requests received by the controller
from that node are accepted.
21
asynReqResource53
RSC
If bit 21 is set to 1b for local bus node number 53, asynchronous requests received by the controller
from that node are accepted.
20
asynReqResource52
RSC
If bit 20 is set to 1b for local bus node number 52, asynchronous requests received by the controller
from that node are accepted.
19
asynReqResource51
RSC
If bit 19 is set to 1b for local bus node number 51, asynchronous requests received by the controller
from that node are accepted.
18
asynReqResource50
RSC
If bit 18 is set to 1b for local bus node number 50, asynchronous requests received by the controller
from that node are accepted.
17
asynReqResource49
RSC
If bit 17 is set to 1b for local bus node number 49, asynchronous requests received by the controller
from that node are accepted.
16
asynReqResource48
RSC
If bit 16 is set to 1b for local bus node number 48, asynchronous requests received by the controller
from that node are accepted.
15
asynReqResource47
RSC
If bit 15 is set to 1b for local bus node number 47, asynchronous requests received by the controller
from that node are accepted.
14
asynReqResource46
RSC
If bit 14 is set to 1b for local bus node number 46, asynchronous requests received by the controller
from that node are accepted.
13
asynReqResource45
RSC
If bit 13 is set to 1b for local bus node number 45, asynchronous requests received by the controller
from that node are accepted.
12
asynReqResource44
RSC
If bit 12 is set to 1b for local bus node number 44, asynchronous requests received by the controller
from that node are accepted.
11
asynReqResource43
RSC
If bit 11 is set to 1b for local bus node number 43, asynchronous requests received by the controller
from that node are accepted.
10
asynReqResource42
RSC
If bit 10 is set to 1b for local bus node number 42, asynchronous requests received by the controller
from that node are accepted.
9
asynReqResource41
RSC
If bit 9 is set to 1b for local bus node number 41, asynchronous requests received by the controller
from that node are accepted.
8
asynReqResource40
RSC
If bit 8 is set to 1b for local bus node number 40, asynchronous requests received by the controller
from that node are accepted.
7
asynReqResource39
RSC
If bit 7 is set to 1b for local bus node number 39, asynchronous requests received by the controller
from that node are accepted.
6
asynReqResource38
RSC
If bit 6 is set to 1b for local bus node number 38, asynchronous requests received by the controller
from that node are accepted.
5
asynReqResource37
RSC
If bit 5 is set to 1b for local bus node number 37, asynchronous requests received by the controller
from that node are accepted.
4
asynReqResource36
RSC
If bit 4 is set to 1b for local bus node number 36, asynchronous requests received by the controller
from that node are accepted.
Submit Documentation Feedback
DESCRIPTION
1394 OHCI Memory-Mapped Register Space
159
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 8-27. Asynchronous Request Filter High Register Description (continued)
BIT
FIELD NAME
TYPE
3
asynReqResource35
RSC
If bit 3 is set to 1b for local bus node number 35, asynchronous requests received by the controller
from that node are accepted.
2
asynReqResource34
RSC
If bit 2 is set to 1b for local bus node number 34, asynchronous requests received by the controller
from that node are accepted.
1
asynReqResource33
RSC
If bit 1 is set to 1b for local bus node number 33, asynchronous requests received by the controller
from that node are accepted.
0
asynReqResource32
RSC
If bit 0 is set to 1b for local bus node number 32, asynchronous requests received by the controller
from that node are accepted.
160
DESCRIPTION
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.36 Asynchronous Request Filter Low Register
The asynchronous request filter low set/clear register enables asynchronous receive requests on a
per-node basis, and handles the lower node IDs. Other than filtering different node IDs, this register
behaves identically to the asynchronous request filter high register. See Table 8-28 for a complete
description of the register contents.
OHCI register offset:
108h set register
10Ch clear register
Register type:
Read/Set/Clear
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-28. Asynchronous Request Filter Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
asynReqResource31
RSC
If bit 31 is set to 1b for local bus node number 31, asynchronous requests received by the
controller from that node are accepted.
30
asynReqResource30
RSC
If bit 30 is set to 1b for local bus node number 30, asynchronous requests received by the
controller from that node are accepted.
29-2
asynReqResourcen
RSC
Bits 29 through 2 (asynReqResourcen, where n = 29, 28, 27, ..., 2) follow the same pattern
as bits 31 and 30.
1
asynReqResource1
RSC
If bit 1 is set to 1b for local bus node number 1, asynchronous requests received by the
controller from that node are accepted.
0
asynReqResource0
RSC
If bit 0 is set to 1b for local bus node number 0, asynchronous requests received by the
controller from that node are accepted.
8.37 Physical Request Filter High Register
The physical request filter high set/clear register enables physical receive requests on a per-node basis,
and handles the upper node IDs. When a packet is destined for the physical request context and the node
ID has been compared against the ARRQ registers, the comparison is done again with this register. If the
bit corresponding to the node ID is not set to 1b in this register, the request is handled by the ARRQ
context instead of the physical request context. The node ID comparison is done if the source node is on
the same bus as the controller. Nonlocal bus-sourced packets are not acknowledged unless bit 31 in this
register is set to 1b. See Table 8-29 for a complete description of the register contents.
OHCI register offset:
110h set register
114h clear register
Register type:
Read/Set/Clear
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
161
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 8-29. Physical Request Filter High Register Description
BIT
FIELD NAME
TYPE
31
physReqAllBusses
RSC
If bit 31 is set to 1b, all asynchronous requests received by the controller from nonlocal bus nodes
are accepted. Bit 31 is not cleared by a PRST.
30
physReqResource
62
RSC
If bit 30 is set to 1b for local bus node number 62, physical requests received by the controller from
that node are handled through the physical request context.
29
physReqResource
61
RSC
If bit 29 is set to 1b for local bus node number 61, physical requests received by the controller from
that node are handled through the physical request context.
28
physReqResource
60
RSC
If bit 28 is set to 1b for local bus node number 60, physical requests received by the controller from
that node are handled through the physical request context.
27
physReqResource
59
RSC
If bit 27 is set to 1b for local bus node number 59, physical requests received by the controller from
that node are handled through the physical request context.
26
physReqResource
58
RSC
If bit 26 is set to 1b for local bus node number 58, physical requests received by the controller from
that node are handled through the physical request context.
25
physReqResource
57
RSC
If bit 25 is set to 1b for local bus node number 57, physical requests received by the controller from
that node are handled through the physical request context.
24
physReqResource
56
RSC
If bit 24 is set to 1b for local bus node number 56, physical requests received by the controller from
that node are handled through the physical request context.
23
physReqResource
55
RSC
If bit 23 is set to 1b for local bus node number 55, physical requests received by the controller from
that node are handled through the physical request context.
22
physReqResource
54
RSC
If bit 22 is set to 1b for local bus node number 54, physical requests received by the controller from
that node are handled through the physical request context.
21
physReqResource
53
RSC
If bit 21 is set to 1b for local bus node number 53, physical requests received by the controller from
that node are handled through the physical request context.
20
physReqResource
52
RSC
If bit 20 is set to 1b for local bus node number 52, physical requests received by the controller from
that node are handled through the physical request context.
19
physReqResource
51
RSC
If bit 19 is set to 1b for local bus node number 51, physical requests received by the controller from
that node are handled through the physical request context.
18
physReqResource
50
RSC
If bit 18 is set to 1b for local bus node number 50, physical requests received by the controller from
that node are handled through the physical request context.
17
physReqResource
49
RSC
If bit 17 is set to 1b for local bus node number 49, physical requests received by the controller from
that node are handled through the physical request context.
16
physReqResource
48
RSC
If bit 16 is set to 1b for local bus node number 48, physical requests received by the controller from
that node are handled through the physical request context.
15
physReqResource
47
RSC
If bit 15 is set to 1b for local bus node number 47, physical requests received by the controller from
that node are handled through the physical request context.
14
physReqResource
46
RSC
If bit 14 is set to 1b for local bus node number 46, physical requests received by the controller from
that node are handled through the physical request context.
13
physReqResource
45
RSC
If bit 13 is set to 1b for local bus node number 45, physical requests received by the controller from
that node are handled through the physical request context.
12
physReqResource
44
RSC
If bit 12 is set to 1b for local bus node number 44, physical requests received by the controller from
that node are handled through the physical request context.
11
physReqResource
43
RSC
If bit 11 is set to 1b for local bus node number 43, physical requests received by the controller from
that node are handled through the physical request context.
10
physReqResource
42
RSC
If bit 10 is set to 1b for local bus node number 42, physical requests received by the controller from
that node are handled through the physical request context.
9
physReqResource
41
RSC
If bit 9 is set to 1b for local bus node number 41, physical requests received by the controller from
that node are handled through the physical request context.
8
physReqResource
40
RSC
If bit 8 is set to 1b for local bus node number 40, physical requests received by the controller from
that node are handled through the physical request context.
7
physReqResource
39
RSC
If bit 7 is set to 1b for local bus node number 39, physical requests received by the controller from
that node are handled through the physical request context.
6
physReqResource
38
RSC
If bit 6 is set to 1b for local bus node number 38, physical requests received by the controller from
that node are handled through the physical request context.
5
physReqResource
37
RSC
If bit 5 is set to 1b for local bus node number 37, physical requests received by the controller from
that node are handled through the physical request context.
4
physReqResource
36
RSC
If bit 4 is set to 1b for local bus node number 36, physical requests received by the controller from
that node are handled through the physical request context.
162
DESCRIPTION
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-29. Physical Request Filter High Register Description (continued)
BIT
FIELD NAME
TYPE
3
physReqResource
35
RSC
If bit 3 is set to 1b for local bus node number 35, physical requests received by the controller from
that node are handled through the physical request context.
2
physReqResource
34
RSC
If bit 2 is set to 1b for local bus node number 34, physical requests received by the controller from
that node are handled through the physical request context.
1
physReqResource
33
RSC
If bit 1 is set to 1b for local bus node number 33, physical requests received by the controller from
that node are handled through the physical request context.
0
physReqResource
32
RSC
If bit 0 is set to 1b for local bus node number 32, physical requests received by the controller from
that node are handled through the physical request context.
Submit Documentation Feedback
DESCRIPTION
1394 OHCI Memory-Mapped Register Space
163
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.38 Physical Request Filter Low Register
The physical request filter low set/clear register enables physical receive requests on a per-node basis,
and handles the lower node IDs. When a packet is destined for the physical request context and the node
ID has been compared against the asynchronous request filter registers, the node ID comparison is done
again with this register. If the bit corresponding to the node ID is not set to 1b in this register, the request
is handled by the asynchronous request context instead of the physical request context. See Table 8-30
for a complete description of the register contents.
OHCI register offset:
118h set register
11Ch clear register
Register type:
Read/Set/Clear
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 8-30. Physical Request Filter Low Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
physReqResource3
1
RSC
If bit 31 is set to 1b for local bus node number 31, physical requests received by the controller
from that node are handled through the physical request context.
30
physReqResource3
0
RSC
If bit 30 is set to 1b for local bus node number 30, physical requests received by the controller
from that node are handled through the physical request context.
29-2
physReqResourcen
RSC
Bits 29 through 2 (physReqResourcen, where n = 29, 28, 27, ..., 2) follow the same pattern as
bits 31 and 30.
1
physReqResource1
RSC
If bit 1 is set to 1b for local bus node number 1, physical requests received by the controller from
that node are handled through the physical request context.
0
physReqResource0
RSC
If bit 0 is set to 1b for local bus node number 0, physical requests received by the controller from
that node are handled through the physical request context.
8.39 Physical Upper Bound Register (Optional Register)
The physical upper bound register is an optional register and is not implemented. This register returns
0000 0000h when read.
OHCI register offset:
120h
Register type:
Read only
Default value:
164
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.40 Asynchronous Context Control Register
The asynchronous context control set/clear register controls the state and indicates status of the DMA
context. See Table 8-31 for a complete description of the register contents.
OHCI register offset: 180h
set register
(ATRQ)
184h
clear register
(ATRQ)
1A0h
set register
[ATRS]
1A4h
clear register
[ATRS]
1C0h
set register
(ARRQ)
1C4h
clear register
(ARRQ)
1E0h
set register
(ARRS)
1E4h
clear register
(ARRS)
Register type:
Read/Set/Clear/Update, Read/Set/Update, Read/Update, Read only
Default value:
0000 X0XXh
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
Table 8-31. Asynchronous Context Control Register Description
BIT
31-16
15
FIELD NAME
RSVD
run
TYPE
R
RSCU
DESCRIPTION
Reserved. Bits 31-16 return 0000h when read.
Run. Bit 15 is set to 1b by software to enable descriptor processing for the context and cleared
by software to stop descriptor processing. The controller changes this bit only on a system
(hardware) or software reset.
14-13
RSVD
R
12
wake
RSU
11
dead
RU
Dead. The controller sets bit 11 to 1b when it encounters a fatal error, and clears the bit when
software clears bit 15 (run). Asynchronous contexts supporting out-of-order pipelining provide
unique ContextControl.dead functionality. See Section 7.7 in the 1394 Open Host Controller
Interface Specification, Release 1.1 for more information.
10
active
RU
Active. The controller sets bit 10 to 1b when it is processing descriptors.
9
betaFrame
RU
Beta frame. Set to 1 when the PHY indicates that the received packet is sent in beta format. A
response to a request sent using beta format also uses beta format.
8
RSVD
7-5
spd
R
RU
Reserved. Bits 14 and 13 return 00b when read.
Wake. Software sets bit 12 to 1b to cause the controller to continue or resume descriptor
processing. The controller clears this bit on every descriptor fetch.
Reserved. Bit 8 returns 0b when read.
Speed. This field indicates the speed at which a packet was received or transmitted and only
contains meaningful information for receive contexts. This field is encoded as:
000 =
001 =
010 =
011 =
100M
200M
400M
800M
bit/s
bit/s
bit/s
bit/s0
All other values are reserved.
4-0
eventcode
Submit Documentation Feedback
RU
Event code. This field holds the acknowledge sent by the link core for this packet or an
internally-generated error code if the packet was not transferred successfully.
1394 OHCI Memory-Mapped Register Space
165
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.41 Asynchronous Context Command Pointer Register
The asynchronous context command pointer register contains a pointer to the address of the first
descriptor block that the controller accesses when software enables the context by setting bit 15 (run) in
the asynchronous context control register (see Section 8.40) to 1b. See Table 8-32 for a complete
description of the register contents.
OHCI register offset:
18Ch
(ATRQ)
1ACh
(ATRS)
1CCh
(ARRQ)
1ECh
(ARRS)
Register type:
Read/Write/Update
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-32. Asynchronous Context Command Pointer Register Description
BIT
FIELD NAME
TYPE
31-4
descriptorAddress
RWU
Contains the upper 28 bits of the address of a 16-byte aligned descriptor block.
3-0
Z
RWU
Indicates the number of contiguous descriptors at the address pointed to by the descriptor
address. If Z is 0h, it indicates that the descriptorAddress field (bits 31-4) is not valid.
166
DESCRIPTION
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
8.42 Isochronous Transmit Context Control Register
The isochronous transmit context control set/clear register controls options, state, and status for the
isochronous transmit DMA contexts. The n value in the following register addresses indicates the context
number (n = 0, 1, 2, 3, ..., 7). See Table 8-33 for a complete description of the register contents.
OHCI register offset:
200h + (16 * n) set register
204h + (16 * n) clear register
Register type:
Read/Set/Clear/Update, Read/Set/Clear, Read/Set/Update,
Read/Update, Read only
Default value:
XXXX X0XXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
Table 8-33. Isochronous Transmit Context Control Register Description
BIT
31
FIELD NAME
cycleMatchEnable
TYPE
RSCU
(1)
DESCRIPTION
When bit 31 is set to 1b, processing occurs such that the packet described by the context first
descriptor block is transmitted in the cycle whose number is specified in the cycleMatch field
(bits 30-16). The cycleMatch field (bits 30-16) must match the low-order two bits of
cycleSeconds and the 13-bit cycleCount field in the cycle start packet that is sent or received
immediately before isochronous transmission begins. Since the isochronous transmit DMA
controller may work ahead, the processing of the first descriptor block may begin slightly in
advance of the actual cycle in which the first packet is transmitted.
The effects of this bit, however, are impacted by the values of other bits in this register and are
explained in the 1394 Open Host Controller Interface Specification. Once the context has
become active, hardware clears this bit.
30-16
15
cycleMatch
RSC
This field contains a 15-bit value, corresponding to the low-order two bits of the isochronous
cycle timer register at OHCI offset F0h (see Section 8.34) cycleSeconds field (bits 31-25) and
the cycleCount field (bits 24-12). If bit 31 (cycleMatchEnable) is set to 1b, this isochronous
transmit DMA context becomes enabled for transmits when the low-order two bits of the
isochronous cycle timer register at OHCI offset F0h cycleSeconds field (bits 31-25) and the
cycleCount field (bits 24-12) value equal this field (cycleMatch) value.
run
RSC
Bit 15 is set to 1b by software to enable descriptor processing for the context and cleared by
software to stop descriptor processing. The controller changes this bit only on a system
(hardware) or software reset.
14-13
RSVD
R
12
wake
RSU
11
dead
RU
The controller sets bit 11 to 1b when it encounters a fatal error, and clears the bit when
software clears bit 15 (run) to 0b.
The controller sets bit 10 to 1b when it is processing descriptors.
(1)
10
active
RU
9-5
RSVD
R
4-0
eent code
On
1.
2.
3.
RU
Reserved. Bits 14 and 13 return 00b when read.
Software sets bit 12 to 1b to cause the controller to continue or resume descriptor processing.
The controller clears this bit on every descriptor fetch.
Reserved. Bits 9-5 return 00000b when read.
Following an OUTPUT_LAST* command, the error code is indicated in this field. Possible
values are ack_complete, evt_descriptor_read, evt_data_read, and evt_unknown.
an overflow for each running context, the isochronous transmit DMA supports up to seven cycle skips when the following are true:
Bit 11 (dead) in either the isochronous transmit or receive context control register is set to 1b.
Bits 4-0 (eventcode field) in either the isochronous transmit or receive context control register are set to evt_timeout.
Bit 24 (unrecoverableError) in the interrupt event register at OHCI offset 80h/84h (see Section 8.21) is set to 1b.
Submit Documentation Feedback
1394 OHCI Memory-Mapped Register Space
167
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.43 Isochronous Transmit Context Command Pointer Register
The isochronous transmit context command pointer register contains a pointer to the address of the first
descriptor block that the controller accesses when software enables an isochronous transmit context by
setting bit 15 (run) in the isochronous transmit context control register (see Section 8.42) to 1b. The
isochronous transmit DMA context command pointer can be read when a context is active. The n value in
the following register addresses indicates the context number (n = 0, 1, 2, 3, ..., 7).
OHCI register offset:
20Ch + (16 * n)
Register type:
Read only
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
8.44 Isochronous Receive Context Control Register
The isochronous receive context control set/clear register controls options, state, and status for the
isochronous receive DMA contexts. The n value in the following register addresses indicates the context
number (n = 0, 1, 2, 3). See Table 8-34 for a complete description of the register contents.
168
OHCI register offset:
400h + (32 * n) set register
404h + (32 * n) clear register
Register type:
Read/Set/Clear/Update, Read/Set/Clear, Read/Set/Update,
Read/Update, Read only
Default value:
XX00 X0XXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
0
25
0
24
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
X
0
0
0
0
X
X
X
X
X
X
X
X
1394 OHCI Memory-Mapped Register Space
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 8-34. Isochronous Receive Context Control Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
bufferFill
RSC
Buffer fill. When bit 31 is set to 1b, received packets are placed back to back to completely fill
each receive buffer. When this bit is cleared, each received packet is placed in a single buffer.
If bit 28 (multiChanMode) is set to 1b, this bit must also be set to 1b. The value of this bit must
not be changed while bit 10 (active) or bit 15 (run) is set to 1b.
30
isochHeader
RSC
Isochronous header. When bit 30 is set to 1b, received isochronous packets include the
complete 4-byte isochronous packet header seen by the link layer. The end of the packet is
marked with a xferStatus in the first doublet, and a 16-bit timestamp indicating the time of the
most recently received (or sent) cycleStart packet.
When this bit is cleared, the packet header is stripped from received isochronous packets. The
packet header, if received, immediately precedes the packet payload. The value of this bit must
not be changed while bit 10 (active) or bit 15 (run) is set to 1b.
29
cycleMatchEnable
28
multiChanMode
RSCU
Cycle match enable. When bit 29 is set to 1b and the 13-bit cycleMatch field (bits 24-12) in the
isochronous receive context match register (See Section 8.46) matches the 13-bit cycleCount
field in the cycleStart packet, the context begins running. The effects of this bit, however, are
impacted by the values of other bits in this register. Once the context has become active,
hardware clears this bit. The value of this bit must not be changed while bit 10 (active) or bit 15
(run) is set to 1b.
RSC
Multichannel mode. When bit 28 is set to 1b, the corresponding isochronous receive DMA
context receives packets for all isochronous channels enabled in the isochronous receive
channel mask high register at OHCI offset 70h/74h (see Section 8.19) and isochronous receive
channel mask low register at OHCI offset 78h/7Ch (see Section 8.20). The isochronous channel
number specified in the isochronous receive context match register (see Section 8.46) is
ignored.
When this bit is cleared, the isochronous receive DMA context receives packets for the single
channel specified in the isochronous receive context match register (see Section 8.46). Only
one isochronous receive DMA context may use the isochronous receive channel mask registers
(see Section 8.19, and Section 8.20). If more than one isochronous receive context control
register has this bit set, the results are undefined. The value of this bit must not be changed
while bit 10 (active) or bit 15 (run) is set to 1b.
27
26-16
15
dualBufferMode
RSVD
run
RSC
R
RSCU
Dual-buffer mode. When bit 27 is set to 1b, receive packets are separated into first and second
payload and streamed independently to the firstBuffer series and secondBuffer series as
described in Section 10.2.3 in the 1394 Open Host Controller Interface Specification. Also,
when bit 27 is set to 1b, both bits 28 (multiChanMode) and 31 (bufferFill) are cleared to 00b.
The value of this bit does not change when either bit 10 (active) or bit 15 (run) is set to 1b.
Reserved. Bits 26-16 return 000 0000 0000b when read.
Run. Bit 15 is set to 1b by software to enable descriptor processing for the context and cleared
by software to stop descriptor processing. The controller changes this bit only on a system
(hardware) or software reset.
14-13
RSVD
R
12
wake
RSU
11
dead
RU
Dead. The controller sets bit 11 to 1b when it encounters a fatal error, and clears the bit when
software clears bit 15 (run).
10
active
RU
Active. The controller sets bit 10 to 1b when it is processing descriptors.
9
betaFrame
RU
Beta frame. Set to 1 when the PHY indicates that the received packet is sent in beta format. A
response to a request sent using beta format also uses beta format.
9-8
RSVD
7-8
spd
R
RU
Reserved. Bits 14 and 13 return 00b when read.
Wake. Software sets bit 12 to 1b to cause the controller to continue or resume descriptor
processing. The controller clears this bit on every descriptor fetch.
Reserved. Bit 8 returns 0b when read.
Speed. This field indicates the speed at which the packet was received.
000 =
001 =
010 =
011 =
100M
200M
400M
800M
bit/s
bit/s
bit/s
bit/s0
All other values are reserved.
4-0
event code
Submit Documentation Feedback
RU
For bufferFill mode, possible values are ack_complete, evt_descriptor_read, evt_data_write,
and evt_unknown. Packets with data errors (either dataLength mismatches or dataCRC errors)
and packets for which a FIFO overrun occurred are backed out. For packet-per-buffer mode,
possible values are ack_complete, ack_data_error, evt_long_packet, evt_overrun,
evt_descriptor_read, evt_data_write, and evt_unknown.
1394 OHCI Memory-Mapped Register Space
169
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
8.45 Isochronous Receive Context Command Pointer Register
The isochronous receive context command pointer register contains a pointer to the address of the first
descriptor block that the controller accesses when software enables an isochronous receive context by
setting bit 15 (run) in the isochronous receive context control register (see Section 8.44) to 1b. The n
value in the following register addresses indicates the context number (n = 0, 1, 2, 3).
OHCI register offset:
40Ch + (32 * n)
Register type:
Read only
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
X
26
X
25
X
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
8.46 Isochronous Receive Context Match Register
The isochronous receive context match register starts an isochronous receive context running on a
specified cycle number, filters incoming isochronous packets based on tag values, and waits for packets
with a specified sync value. The n value in the following register addresses indicates the context number
(n = 0, 1, 2, 3). See Table 8-35 for a complete description of the register contents.
OHCI register offset:
410h + (32 * n)
Register type:
Read/Write, Read only
Default value:
XXXX XXXXh
BIT NUMBER
RESET STATE
31
X
30
X
29
X
28
X
27
0
26
0
25
0
24
X
23
X
22
X
21
X
20
X
19
X
18
X
17
X
16
X
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Table 8-35. Isochronous Receive Context Match Register Description
BIT
FIELD NAME
TYPE
DESCRIPTION
31
tag3
RW
If bit 31 is set to 1b, this context matches on isochronous receive packets with a tag field of 11b.
30
tag2
RW
If bit 30 is set to 1b, this context matches on isochronous receive packets with a tag field of 10b.
29
tag1
RW
If bit 29 is set to 1b, this context matches on isochronous receive packets with a tag field of 01b.
28
tag0
RW
If bit 28 is set to 1b, this context matches on isochronous receive packets with a tag field of 00b.
27
RSVD
R
Reserved. Bit 27 returns 0b when read.
26-12
cycleMatch
RW
This field contains a 15-bit value corresponding to the two low-order bits of cycleSeconds and the
13-bit cycleCount field in the cycleStart packet. If cycleMatchEnable (bit 29) in the isochronous receive
context control register (see Section 8.44) is set to 1b, this context is enabled for receives when the
two low-order bits of the isochronous cycle timer register at OHCI offset F0h (see Section 8.34)
cycleSeconds field (bits 31-25) and cycleCount field (bits 24-12) value equal this field (cycleMatch)
value.
11-8
sync
RW
This 4-bit field is compared to the sync field of each isochronous packet for this channel when the
command descriptor w field is set to 11b.
7
RSVD
6
tag1SyncFilter
R
RW
Reserved. Bit 7 returns 0b when read.
If bit 6 and bit 29 (tag1) are set to 11b, packets with tag 01b are accepted into the context if the two
most significant bits of the packet sync field are 00b. Packets with tag values other than 01b are
filtered according to bit 28 (tag0), bit 30 (tag2), and bit 31 (tag3) without any additional restrictions.
If this bit is cleared, this context matches on isochronous receive packets as specified in bits 28-31
(tag0-tag3) with no additional restrictions.
5-0
170
channelNumber
RW
This 6-bit field indicates the isochronous channel number for which this isochronous receive DMA
context accepts packets.
1394 OHCI Memory-Mapped Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
Submit Documentation Feedback
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
1394 OHCI Memory-Mapped Register Space
171
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
9
www.ti.com
1394 OHCI Memory-Mapped TI Extension Register Space
The TI extension base address register provides a method of accessing memory-mapped TI extension
registers. See Section 7.9, TI Extension Base Address Register, for register bit field details. See Table 9-1
for the TI extension register listing.
Table 9-1. TI Extension Register Map
9.1
REGISTER NAME
OFFSET
Reserved
00h-A7Fh
Isochronous receive digital video enhancement set
A80h
Isochronous receive digital video enhancement clear
A84h
Link enhancement control set
A88h
Link enhancement control clear
A8Ch
Isochronous transmit context 0 timestamp offset
A90h
Isochronous transmit context 1 timestamp offset
A94h
Isochronous transmit context 2 timestamp offset
A98h
Isochronous transmit context 3 timestamp offset
A9Ch
Isochronous transmit context 4 timestamp offset
AA0h
Isochronous transmit context 5 timestamp offset
AA4h
Isochronous transmit context 6 timestamp offset
AA8h
Isochronous transmit context 7 timestamp offset
AACh
Reserved
AB0h-FFFh
Digital Video (DV) and MPEG2 Timestamp Enhancements
The DV timestamp enhancements are enabled by bit 8 (enab_dv_ts) in the link enhancement control
register located at PCI offset F4h, and are aliased in TI extension register space at offset A88h (set) and
A8Ch (clear).
The DV and MPEG transmit enhancements are enabled separately by bits in the link enhancement control
register located in PCI configuration space at PCI offset F4h. The link enhancement control register is also
aliased as a set/clear register in TI extension space at offset A88h (set) and A8Ch (clear).
Bit 8 (enab_dv_ts) of the link enhancement control register enables DV timestamp support. When
enabled, the link calculates a timestamp based on the cycle timer and the timestamp offset register and
substitutes it in the SYT field of the CIP once per DV frame.
Bit 10 (enab_mpeg_ts) of the link enhancement control register enables MPEG timestamp support. Two
MPEG timestamp modes are supported. The default mode calculates an initial delta that is added to the
calculated timestamp in addition to a user-defined offset. The initial offset is calculated as the difference in
the intended transmit cycle count and the cycle count field of the timestamp in the first TSP of the MPEG2
stream. The use of the initial delta can be controlled by bit 31 (DisableInitialOffset) in the timestamp offset
register (see Section 9.5).
The MPEG2 timestamp enhancements are enabled by bit 10 (enab_mpeg_ts) in the link enhancement
control register located at PCI offset F4h, and aliased in TI extension register space at offset A88h (set)
and A8Ch (clear).
When bit 10 (enab_mpeg_ts) is set to 1b, the hardware applies the timestamp enhancements to
isochronous transmit packets that have the tag field equal to 01b in the isochronous packet header and a
FMT field equal to 10h.
172
1394 OHCI Memory-Mapped TI Extension Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
9.2
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Isochronous Receive Digital Video Enhancements
The DV frame sync and branch enhancement provides a mechanism in buffer-fill mode to synchronize
1394 DV data that is received in the correct order to DV frame-sized data buffers described by several
INPUT_MORE descriptors (see 1394 Open Host Controller Interface Specification, Release 1.1). This is
accomplished by waiting for the start-of-frame packet in a DV stream before transferring the received
isochronous stream into the memory buffer described by the INPUT_MORE descriptors. This can improve
the DV capture application performance by reducing the amount of processing overhead required to strip
the CIP header and copy the received packets into frame-sized buffers.
The start of a DV frame is represented in the 1394 packet as a 16-bit pattern of 1FX7h (first byte 1Fh and
second byte X7h) received as the first two bytes of the third quadlet in a DV isochronous packet.
9.3
Isochronous Receive Digital Video Enhancement Registers
The isochronous receive digital video enhancement registers enable the DV enhancements in the
controller. The bits in these registers may only be modified when both the active (bit 10) and run (bit 15)
bits of the corresponding context control register are 00b. See Table 9-2 for a complete description of the
register contents.
TI extension register offset:
A80h set register
A84h clear register
Register type:
Read/Set/Clear, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 9-2. Isochronous Receive Digital Video Enhancement Registers Description
BIT
31-14
FIELD NAME
RSVD
TYPE
R
DESCRIPTION
Reserved. Bits 31-14 return 00 0000 0000 0000 0000b when read.
13
DV_Branch3
RSC
When bit 13 is set to 1b, the isochronous receive context 3 synchronizes reception to the DV frame
start tag in bufferfill mode if input_more.b = 01b, and jumps to the descriptor pointed to by
frameBranch if a DV frame start tag is received out of place. This bit is only interpreted when bit 12
(CIP_Strip3) is set to 1b and bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 460h/464h (see Section 8.44) is cleared to 0b.
12
CIP_Strip3
RSC
When bit 12 is set to 1b, the isochronous receive context 3 strips the first two quadlets of payload.
This bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control
register at OHCI offset 460h/464h (see Section 8.44) is cleared to 0b.
11-10
RSVD
R
Reserved. Bits 11 and 10 return 00b when read.
9
DV_Branch2
RSC
When bit 9 is set to 1b, the isochronous receive context 2 synchronizes reception to the DV frame
start tag in bufferfill mode if input_more.b = 01b, and jumps to the descriptor pointed to by
frameBranch if a DV frame start tag is received out of place. This bit is only interpreted when bit 8
(CIP_Strip2) is set to 1b and bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 440h/444h (see Section 8.44) is cleared to 0b.
8
CIP_Strip2
RSC
When bit 8 is set to 1b, the isochronous receive context 2 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 440h/444h (see Section 8.44) is cleared to 0b.
7-6
RSVD
R
Reserved. Bits 7 and 6 return 00b when read.
5
DV_Branch1
TSC
When bit 5 is set to 1b, the isochronous receive context 1 synchronizes reception to the DV frame
start tag in bufferfill mode if input_more.b = 01b, and jumps to the descriptor pointed to by
frameBranch if a DV frame start tag is received out of place. This bit is only interpreted when bit 4
(CIP_Strip1) is set to 1b and bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 420h/424h (see Section 8.44) is cleared to 0b.
4
CIP_Strip1
RSC
When bit 4 is set to 1b, the isochronous receive context 1 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 420h/424h (see Section 8.44) is cleared to 0b.
Submit Documentation Feedback
1394 OHCI Memory-Mapped TI Extension Register Space
173
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 9-2. Isochronous Receive Digital Video Enhancement Registers Description (continued)
BIT
FIELD NAME
3-2
TYPE
RSVD
DESCRIPTION
R
Reserved. Bits 3 and 2 return 00b when read.
1
DV_Branch0
RSC
When bit 1 is set to 1b, the isochronous receive context 0 synchronizes reception to the DV frame
start tag in bufferfill mode if input_more.b = 01b and jumps to the descriptor pointed to by frameBranch
a DV frame start tag is received out of place. This bit is only interpreted when bit 0 (CIP_Strip0) is set
to 1b and bit 30 (isochHeader) in the isochronous receive context control register at OHCI offset
400h/404h (see Section 8.44) is cleared to 0b.
0
CIP_Strip0
RSC
When bit 0 is set to 1b, the isochronous receive context 0 strips the first two quadlets of payload. This
bit is only interpreted when bit 30 (isochHeader) in the isochronous receive context control register at
OHCI offset 400h/404h (see Section 8.44) is cleared to 0b.
9.4
Link Enhancement Control Registers
These registers are a memory-mapped set/clear registers that are an alias of the link enhancement control
register at PCI offset F4h. These bits may be initialized by software. Some of the bits may also be
initialized by a serial EEPROM, if one is present, as noted in the following bit descriptions. If the bits are to
be initialized by software, the bits must be initialized prior to setting bit 19 (LPS) in the host controller
control register at OHCI offset 50h/54h (see Section 3.3.2). See Table 9-3 for a complete description of
the register contents.
TI extension register offset:
A88h set register
A8Ch clear register
Register type:
Read/Set/Clear, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
0
Table 9-3. Link Enhancement Control Registers Description
BIT
FIELD NAME
TYPE
31-16
RSVD
15 (1)
dis_at_pipleline
RW
Disable AT pipelining. When bit 15 is set to 1b, out-of-order AT pipelining is disabled. The default
value for this bit is 0b.
14(1)
RSVD
RW
Reserved. Bit 14 defaults to 0b and must remain 0b for normal operation of the OHCI core.
(1)
174
R
DESCRIPTION
Reserved. Bits 31-16 return 0000h when read.
This bit is reset by PERST or FRST.
1394 OHCI Memory-Mapped TI Extension Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 9-3. Link Enhancement Control Registers Description (continued)
BIT
13-12 (1)
FIELD NAME
atx_thresh
TYPE
DESCRIPTION
RW
This field sets the initial AT threshold value, which is used until the AT FIFO is underrun. When the
OHCI controller retries the packet, it uses a 2K-byte threshold, resulting in a store-and-forward
operation.
00 =
01 =
10 =
11 =
Threshold
Threshold
Threshold
Threshold
~2K bytes resulting in a store-and-forward operation
~1.7K bytes (default)
~1K bytes
~512 bytes
These bits fine tune the asynchronous transmit threshold. For most applications the 1.7K-byte
threshold is optimal. Changing this value may increase or decrease the 1394 latency depending on
the average PCI bus latency.
Setting the AT threshold to 1.7K, 1K, or 512 bytes results in data being transmitted at these
thresholds or when an entire packet has been checked into the FIFO. If the packet to be
transmitted is larger than the AT threshold, the remaining data must be received before the AT
FIFO is emptied; otherwise, an underrun condition occurs, resulting in a packet error at the
receiving node. As a result, the link then commences store-and-forward operation. Wait until it has
the complete packet in the FIFO before retransmitting it on the second attempt to ensure delivery.
An AT threshold of 2K results in store-and-forward operation, which means that asynchronous data
will not be transmitted until an end-of-packet token is received. Restated, setting the AT threshold
to 2K results in only complete packets being transmitted.
Note that the OHCI controller will always use store-and-forward when the asynchronous transmit
retries register at OHCI offset 08h (see Section 8.3, Asynchronous Transmit Retries Register) is
cleared.
11
10(1)
9
RSVD
enab_mpeg_ts
R
RW
RSVD
R
Reserved. Bit 11 returns 0b when read.
Enable MPEG timestamp enhancement. When this bit is set, Cheetah-Express shall apply time
stamp enhancements to isochronous transmit packets that have the tag field equal to 2b01 in the
isochronous packet header and a FMT field equal to 6h10.
Reserved. Bit 9 returns 0b when read.
8(1)
enab_dv_ts
RW
Enable DV CIP timestamp enhancement. When bit 8 is set to 1b, the enhancement is enabled for
DV CIP transmit streams (FMT = 00h). The default value for this bit is 0b.
7(1)
enab_unfair
RW
Enable asynchronous priority requests (OHCI-Lynx compatible). Setting bit 7 to 1b enables the link
to respond to requests with priority arbitration. It is recommended that this bit be set to 1b. The
default value for this bit is 0b.
6-3
RSVD
2(1)
enab_insert_idle
RW
Enable insert idle (OHCI-Lynx compatible). When the PHY has control of the Ct[0:1] internal control
lines and D[0:8] internal data lines and the link requests control, the PHY drives 11b on the Ct[0:1]
lines. The link can then start driving these lines immediately. Setting this bit to 1 inserts an idle
state, so the link waits one clock cycle before it starts driving the lines (turnaround time). It is
recommended that this bit be set to 1. For use with TI phys this bit should be set to 0. If a serial
EEPROM is implemented this bit is initialized with the value of EEPROM word 0x05 bit 2.
1(1)
enab_accel
RW
Enable acceleration enhancements (OHCI-Lynx compatible). When bit 1 is set to 1b, the PHY is
notified that the link supports the IEEE Std 1394a-2000 acceleration enhancements, that is,
ack-accelerated, fly-by concatenation, etc. It is recommended that this bit be set to 1b. The default
value for this bit is 0b.
0
R
RSVD
Submit Documentation Feedback
R
Reserved. Bits 6-3 return 0h when read.
Reserved. Bit 0 returns 0b when read.
1394 OHCI Memory-Mapped TI Extension Register Space
175
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
9.5
www.ti.com
Timestamp Offset Registers
The value of these registers is added as an offset to the cycle timer value when using the MPEG, DV, and
CIP enhancements. A timestamp offset register is implemented per isochronous transmit context. The n
value following the offset indicates the context number (n = 0, 1, 2, 3, ..., 7). These registers are
programmed by software as appropriate. See Table 9-4 for a complete description of the register contents.
TI extension register offset:
A90h + (4*n)
Register type:
Read/Write, Read only
Default value:
0000 0000h
BIT NUMBER
RESET STATE
31
0
30
0
29
0
28
0
27
0
26
0
25
0
24
0
23
0
22
0
21
0
20
0
19
0
18
0
17
0
16
0
BIT NUMBER
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
RESET STATE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Table 9-4. Timestamp Offset Registers Description
BIT
FIELD NAME
31
DisableInitialOffset
TYPE
RW
Bit 31 disables the use of the initial timestamp offset when the MPEG2 enhancements are
enabled. A value of 0b indicates the use of the initial offset, a value of 1b indicates that the
initial offset must not be applied to the calculated timestamp. This bit has no meaning for the
DV timestamp enhancements. The default value for this bit is 0b.
3-=25
RSVD
24-12
CycleCount
RW
This field adds an offset to the cycle count field in the timestamp when the DV or MPEG2
enhancements are enabled. The cycle count field is incremented modulo 8000; therefore,
values in this field must be limited between 0 and 7999. The default value for this field is all 0s.
11-0
CycleOffset
RW
This field adds an offset to the cycle offset field in the timestamp when the DV or MPEG2
enhancements are enabled. The cycle offset field is incremented modulo 3072; therefore,
values in this field must be limited between 0 and 3071. The default value for this field is all 0s.
176
R
DESCRIPTION
Reserved. Bits 30-25 return 000 0000b when read.
1394 OHCI Memory-Mapped TI Extension Register Space
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
10
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Physical Layer (PHY) Section
The cable interface can follow either the IEEE Std 1394a-2000 protocol or the IEEE Std 1394b-2002
protocol on both ports. The mode of operation is determined by the interface capabilities of the ports
being connected. When either of the ports is connected to an IEEE Std 1394a-2000-compliant device,
the cable interface on that port operates in the IEEE Std 1394a-2000 data-strobe mode at a compatible
S100, S200, or S400 speed. When a bilingual port is connected to an IEEE Std 1394b-2002-compliant
node, the cable interface on that port operates per the IEEE Std 1394b-2002 standard at S400B or
S800 speed. The XIO2213B automatically determines the correct cable interface connection method
for the bilingual ports.
To operate a port as an IEEE Std 1394b-2002 bilingual port, the data-strobe-only terminal for the port
(DS0, DS1, or DS2_P ) must be pulled to ground through a 1-kΩ resistor. The port must be operated in
the IEEE Std 1394b-2002 bilingual mode whenever an IEEE Std 1394b-2002 bilingual or an IEEE Std
1394b-2002 beta-only connector is connected to the port. To operate the port as an IEEE Std
1394a-2000-only port, the data-strobe-only terminal (DS0, DS1, or DS2_P) must be pulled to 3.3-V VCC
through a 1-kΩ resistor. The only time the port must be forced to the data-strobe-only mode is if the
port is connected to an IEEE Std 1394a-2000 connector [either 6 pin (recommended) or 4 pin]. This
mode is provided to ensure that IEEE Std 1394b-2002 signaling is never sent across an IEEE Std
1394a-2000 cable.
During packet reception, the serial data bits are split into 2-, 4-, or 8-bit parallel streams by the PHY
section and sent to the link-layer controller (LLC) section. The received data is also transmitted
(repeated) on the other connected and active cable ports.
Both the twisted pair A (TPA) and the twisted pair B (TPB) cable interfaces incorporate differential
comparators to monitor the line states during initialization and arbitration when connected to an IEEE
Std 1394a-2000-compliant device. The outputs of these comparators are used by the internal logic to
determine the arbitration status. The TPA channel monitors the incoming cable common-mode voltage.
The value of this common-mode voltage is used during IEEE Std 1394a-2000-mode arbitration and
sets the speed of the next packet transmission. In addition, the TPB channel monitors the incoming
cable common-mode voltage on the TPB pair for the presence of the remotely supplied twisted pair
bias (TPBIAS) voltage.
When connected to an IEEE Std 1394a-2000-compliant node, the XIO2213B PHY section provides a
1.86-V nominal bias voltage at the TPBIAS terminal for port termination. The PHY section contains
three independent TPBIAS circuits (one for each port). This bias voltage, when seen through a cable
by a remote receiver, indicates the presence of an active connection. This bias voltage source must be
stabilized by an external filter capacitor of 1 µF.
The line drivers in the XIO2213B PHY section are designed to work with external 112-Ω termination
resistor networks in order to match the 110-Ω cable impedance. One termination network is required at
each end of a twisted-pair cable. Each network is composed of a pair of series-connected 56-Ω
resistors. The midpoint of the pair of resistors that is connected to the TPA terminals is connected to its
corresponding TPBIAS voltage terminal. The midpoint of the pair of resistors that is directly connected
to the TPB terminals is coupled to ground through a parallel RC network, with recommended values of
5 k and 270 pF. The values of the external line-termination resistors are selected to meet the standard
specifications when connected in parallel with the internal receiver circuits. A precision external resistor
connected between the R0 and R1 terminals sets the driver output current, along with other internal
operating currents.
When the power supply of the XIO2213B is off while the twisted-pair cables are connected, the
XIO2213B transmitter and receiver circuitry present to the cable a high-impedance signal that does not
load the device at the other end of the cable.
Submit Documentation Feedback
Physical Layer (PHY) Section
177
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
When the XIO2213B PHY section is used without one or more of the ports brought out to a connector,
the twisted-pair terminals of the unused ports must be terminated for reliable operation. For each
unused port, the port must be forced to the IEEE Std 1394a-2000-only mode (data-strobe-only mode)
by pulling DSn to VCC through a 1KΩ resistor, after which the TPB+ and TPB– terminals can be tied
together and then pulled to ground; or TPB+ and TPB– can be connected to the suggested normal
termination network. TPA+ and TPA– of an unused port can be left unconnected. The TPBIAS terminal
can be connected through a 1-µF capacitor to ground or left unconnected.
The TESTM, SE, and SM terminals are used to set up various manufacturing test conditions. For
normal operation, TESTM must be connected to VDD through a 1-kΩ resistor. The SE and SM
terminals must be tied to ground through a 1-kΩ resistor.
The LPS_P (link power status) terminal of the PHY section works with the LKON terminal to manage
the power usage in the node. The LPS_L signal from the LLC section is used in conjunction with the
LCtrl bit (see Table 10-1 and Table 10-2 ) to indicate the active/power status of the LLC section. The
LPS_P signal also resets, disables, and initializes the PHY-section/LLC-section interface (the state of
the PHY-section/LLC-section interface is controlled solely by the LPS_P input, regardless of the state
of the LCtrl bit). The LPS_P terminal of the PHY section must be connected to the LPS_L terminal of
the LLC section during normal operation.
The LPS_P input is considered inactive if it remains low for more than the PHY_RESET time (see the
LPS terminal definition) and is considered active otherwise. When the PHY section detects that the
LPS_P input is inactive, the PHY-section/LLC-section interface is placed into a low-power reset state in
which the CTL and D outputs are held in the logic 0 state and the LREQ input is ignored; however, the
PCLK output remains active. If the LPS input remains low for more than the LPS_DISABLE time (see
the LPS terminal definition), the PHY-section/LLC-section interface is put into a low-power disabled
state in which the PCLK_P output is also held inactive. The XIO2213B continues the necessary PHY
repeater functions required for normal network operation, regardless of the state of the
PHY-section/LLC-section interface. When the interface is in the reset or disabled state and the LPS
input is again observed active, the PHY section initializes the interface and returns to normal operation.
The PHY-section/LLC-section interface is also held in the disabled state during hardware reset. When
the LPS_P terminal is returned to an active state after being sensed as having entered the
LPS_DISABLE time, the XIO2213B issues a bus reset. This broadcasts the node self-ID packet, which
contains the updated L bit state (the PHY section and LLC section now being accessible).
The PHY section uses the LKON terminal to notify the LLC section to power up and become active.
When activated, the output LKON signal is a square wave. The PHY section activates the LKON
output when the LLC section is inactive and a wake-up event occurs. The LLC section is considered
inactive when either the LPS_P input is inactive, as previously described, or the LCtrl bit is cleared to
0. A wake-up event occurs when a link-on PHY packet addressed to this node is received, or
conditionally when a PHY interrupt occurs. The PHY section deasserts the LKON output when the LLC
section becomes active (both LPS_P sensed as active and the LCtrl bit set to 1). The PHY section also
deasserts the LKON output when a bus reset occurs, unless a PHY interrupt condition exists, which
would otherwise cause LKON to be active. If the XIO2213B is power cycled and the power class is 0
through 4, the PHY section asserts LKON for approximately 167 ms or until both the LPS_P is active
and the LCtrl bit is 1.
10.1 PHY Section Register Configuration
There are 16 accessible PHY section registers in the XIO2213B. The configuration of the registers at
addresses 0h through 7h (the base registers) is fixed, while the configuration of the registers at addresses
8h through Fh (the paged registers) is dependent on which of eight pages, numbered 0h through 7h, is
currently selected. The selected page is set in base register 7h. Note that while this register set is
compatible with IEEE Std 1394a-2000 register sets, some fields have been redefined and this register set
contains additional fields.
Table 10-1 shows the configuration of the base registers, and Table 10-2 gives the corresponding field
descriptions. The base register field definitions are unaffected by the selected page number.
178
Physical Layer (PHY) Section
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
A reserved register or register field (marked as Reserved or RSVD in the following register configuration
tables) is read as 0, but is subject to future usage. All registers in address pages 2 through 6 are
reserved.
Table 10-1. Base Register Description
ADDRESS
BIT POSITION
0
1
RHB
IBR
2
0000
0001
3
4
5
Physical_ID
0010
LCtrl
C
0101
WDIE
ISBR
R
CPS
Num_Ports (00011b)
PHY_Speed (111b)
0100
7
Gap_Count
Extended (111b)
0011
6
RSVD
Delay (0000b)
Jitter (000b)
CTOI
CPSI
0110
Max_Legacy_SPD
BLINK
0111
Page_Select
RSVD
Pwr_Class
STOI
PEI
EAA
Bridge
EMC
RSVD
Port_Select
Table 10-2. Base Register Field Description
SIZE
TYPE
DESCRIPTION
Physical_ID
FIELD
6
Rd
Physical identification. This field contains the physical address ID of this node determined during self-ID.
The Physical_ID is invalid after a bus reset until the self-ID has completed as indicated by an unsolicited
register 0 status transfer from the PHY to the LLC.
R
1
Rd
Root. This bit indicates that this node is the root node. The R bit is reset to 0 by bus reset, and is set to
1 during tree-ID if this node becomes root.
CPS
1
Rd
Cable-power-status. This bit indicates the state of the CPS input terminal. The CPS terminal is normally
tied to serial bus cable power through a 400-kΩ resistor. A 0 in this bit indicates that the cable power
voltage has dropped below its threshold for ensured reliable operation.
RHB
1
Rd/Wr Root-holdoff bit. This bit instructs the PHY to attempt to become root after the next bus reset. The RHB
bit is reset to 0 by a hardware reset and is unaffected by a bus reset. If two nodes on a single bus have
their root holdoff bit set, the result is not defined. To prevent two nodes from having their root-holdoff bit
set, this bit must only be written using a PHY configuration packet.
IBR
1
Rd/Wr Initiate bus reset. This bit instructs the PHY to initiate a long (166 ＝s) bus reset at the next opportunity.
Any receive or transmit operation in progress when this bit is set completes before the bus reset is
initiated. The IBR bit is reset to 0 after a hardware reset or a bus reset. Care must be exercised when
writing to this bit to not change the other bits in this register. It is recommended thatwhenever possible a
bus reset be initiated using the ISBR bit and not the IBR bit.
Gap_Count
6
Rd/Wr Arbitration gap count. This value sets the subaction (fair) gap, arb-reset gap, and arb-delay times. The
gap count can be set either by a write to the register, or by reception or transmission of a PHY_CONFIG
packet. The gap count is reset to 3Fh by hardware reset or after two consecutive bus resets without an
intervening write to the gap count register (either by a write to the PHY register or by a PHY_CONFIG
packet). It is strongly recommended that this field only be changed using PHY configuration packets.
Extended
3
Rd
Extended register definition. For the XIO2213B, this field is 111b, indicating that the extended register
set is implemented.
Num_Ports
4
Rd
Number of ports. This field indicates the number of ports implemented in the PHY. For the XIO2213B,
this field is 3.
PHY_Speed
3
Rd
PHY speed capability. This field is no longer used. For the XIO2213B PHY, this field is 111b. Speeds for
1394b PHYs must be checked on a port-by-port basis.
Delay
4
Rd
PHY repeater data delay. This field indicates the worst-case repeater data delay of the PHY, expressed
as 144 + (delay 20) ns. For the XIO2213B, this field is 02h. This value is the repeater delay for the
S400B case, which is slower than the S800B or 1394a cases. Since the IEEE Std 1394b-2002 PHY
register set only has a single field for the delay parameter, the slowest value is used. If a network uses
only S800B or 1394a connections, a delay value of 00h may be used. The worst-case PHY repeater
delay is 197 ns for S400B and 127 ns for S800B cable speeds (trained, raw bit speed).
Submit Documentation Feedback
Physical Layer (PHY) Section
179
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 10-2. Base Register Field Description (continued)
FIELD
SIZE
TYPE
DESCRIPTION
LCtrl
1
Rd/Wr Link-active status control. This bit controls the indicated active status of the LLC section reported in the
self-ID packet. The logical AND of this bit and the LPS active status is replicated in the L field (bit 9) of
the self-ID packet. The LLC bit in the node self-ID packet is set active only if both the LPS input is active
and the LCtrl bit is set. The LCtrl bit provides a software controllable means to indicate the LLC self-ID
active status in lieu of using the LPS input terminal. The LCtrl bit is set to 1 by hardware reset and is
unaffected by bus reset.
Note: The state of the PHY-section/LLC-section interface is controlled solely by the LPS input,
regardless of the state of the LCtrl bit. If the PHY-section/LLC-section interface is operational as
determined by the LPS input being active, received packets and status information continue to be
presented on the interface, and any requests indicated on the LREQ input are processed, even if the
LCtrl bit is cleared to 0.
C
1
Rd/Wr Contender status. This bit indicates that this node is a contender for the bus or isochronous resource
manager. This bit is replicated in the c field (bit 20) of the self-ID packet. This bit is set to 0 on hardware
reset. After hardware reset, this bit can only be set via a software register write. This bit is unaffected by
a bus reset.
Jitter
3
Pwr_Class
3
Rd/Wr Node power class. This field indicates this node power consumption and source characteristics and is
replicated in the pwr field (bits 21-23) of the self-ID packet. This field is reset to the state specified by
the PC0-PC2 input terminals on a hardware reset, and is unaffected by a bus reset.
WDIE
1
Rd/Wr Watchdog interrupt enable. This bit, if set to 1, enables the port interrupt event (PIE) bit to be set when
resume operations begin on any port, or when any of the CTOI, CPSI, or STOI interrupt bits are set and
the PHY-section/LLC-section interface is nonoperational. This bit is reset to 0 by hardware reset and is
unaffected by bus reset.
ISBR
1
Rd/Wr Initiate short arbitrated bus reset. This bit, if set to 1, instructs the XIO2213B to initiate a short (1.3-ms)
arbitrated bus reset at the next opportunity. This bit is reset to 0 by a bus reset. It is recommended that
short bus reset is the only reset type initiated by software. IEC 61883-6 requires that a node initiate
short bus resets to minimize any disturbance to an audio stream.
Note: Legacy IEEE Std 1394-1995-compliant PHYs are not capable of performing short bus resets.
Therefore, initiation of a short bus reset in a network that contains such a legacy device results in a long
bus reset being performed.
CTOI
1
Rd/Wr Configuration time-out interrupt. This bit is set to 1 when the arbitration controller times out during
tree-ID start, and might indicate that the bus is configured in a loop. This bit is reset to 0 by hardware
reset, or by writing a 1 to this register bit. If the CTOI and WDIE bits are both set and the LLC is or
becomes inactive, the PHY section activates the LKON output to notify the LLC section to service the
interrupt.
Note: If the network is configured in a loop, only those nodes that are part of the loop generate a
configuration time-out interrupt. Instead, all other nodes time out waiting for the tree-ID and/or self-ID
process to complete and then generate a state time-out interrupt and bus reset. This bit is only set when
the bus topology includes IEEE Std 1394a-2000 nodes; otherwise, IEEE Std 1394b-2002 loop healing
prevents loops from being formed in the topology.
CPSI
1
Rd/Wr Cable-power-status interrupt. This bit is set to 1 whenever the CPS input transitions from high to low,
indicating that cable power might be too low for reliable operation. This bit is reset to 1 by hardware
reset. It can be cleared by writing a 1 to this register bit. If the CPSI and WDIE bits are both set and the
LLC section is or becomes inactive, the PHY section activates the LKON output to notify the LLC
section to service the interrupt.
STOI
1
Rd/Wr State time-out interrupt. This bit indicates that a state time-out has occurred (which also causes a bus
reset to occur). This bit is reset to 0 by hardware reset, or by writing a 1 to this register bit. If the STOI
and WDIE bits are both set and the LLC is, or becomes, inactive, the PHY section activates the LKON
output to notify the LLC section to service the interrupt.
PEI
1
Rd/Wr Port event interrupt. This bit is set to 1 on any change in the connected, bias, disabled, or fault bits for
any port for which the port interrupt enable (PIE) bit is set. Additionally, if the resuming port interrupt
enable (WDIE) bit is set, the PEI bit is set to 1 at the start of resume operations on any port. This bit is
reset to 0 by hardware reset, or by writing a 1 to this register bit.
EAA
1
Rd/Wr Enable accelerated arbitration. This bit enables the XIO2213B to perform the various arbitration
acceleration enhancements defined in IEEE Std 1394a-2000 (ack-accelerated arbitration, asynchronous
fly-by concatenation, and isochronous fly-by concatenation). This bit is reset to 0 by hardware reset and
is unaffected by bus reset. This bit has no effect when the device is operating in IEEE Std 1394b-2002
mode.
EMC
1
Rd/Wr Enable multispeed concatenated packets. This bit enables the XIO2213B to transmit concatenated
packets of differing speeds in accordance with the protocols defined in IEEE Std 1394a-2000. This bit is
reset to 0 by hardware reset and is unaffected by bus reset. This bit has no effect when the device is
operating in IEEE Std 1394b-2002 mode.
180
Rd
PHY-section repeater jitter. This field indicates the worst-case difference between the fastest and
slowest repeater data delay, expressed as (jitter + 1) 20 ns. For the XIO2213B, this field is 0.
Physical Layer (PHY) Section
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 10-2. Base Register Field Description (continued)
FIELD
SIZE
TYPE
Max_Legacy_S
PD
3
Rd
Maximum legacy path speed. This field holds the maximum speed capability of any legacy node (IEEE
Std 1394a-2000 or 1394-1995 compliant) as indicated in the self-ID packets received during bus
initialization. Encoding is the same as for the PHY_SPEED field (but limited to S400 maximum).
DESCRIPTION
BLINK
1
Rd
Beta-mode link. This bit indicates that a beta-mode-capable LLC section is attached to the PHY section.
This bit is set by the BMODE input terminal on the XIO2213B and should be set to 1.
Bridge
2
Rd/Wr Bridge. This field controls the value of the bridge (brdg) field in the self-ID packet. The power reset value
is 0. Details for when to set these bits are specified in the IEEE Std 1394.1 bridging specification.
Page_Select
3
Rd/Wr Page select. This field selects the register page to use when accessing register addresses 8-15. This
field is reset to 0 by a hardware reset and is unaffected by bus reset.
Port_Select
4
Rd/Wr Port select. This field selects the port when accessing per-port status or control (for example, when one
of the port status/control registers is accessed in page 0). Ports are numbered starting at 0. This field is
reset to 0 by hardware reset and is unaffected by bus reset.
The port status page provides access to configuration and status information for each of the ports. The
port is selected by writing 0 to the Page_Select field and the desired port number to the Port_Select field
in base register 7. Table 10-3 shows the configuration of the port-status page registers, and Table 10-4
gives the corresponding field descriptions. If the selected port is not implemented, all registers in the port
status page are read as 0.
Table 10-3. Page 0 (Port Status) Register Description
ADDRES
S
1000
1001
BIT POSITION
0
1
2
Astat
3
Bstat
Negotiated_speed
PIE
4
5
6
7
Ch
Con
RxOK
Dis
Fault
Standby_fault
Disscrm
B_Only
1010
DC_connected
Max_port_speed (011b)
LPP
Cable_speed
1011
Connection_unreliable
Reserved
Beta_mode
Reserved
1100
1101
Port_error
Reserved
Loop_disable
1110
Reserved
1111
Reserved
Submit Documentation Feedback
In_standby
Hard_disable
Physical Layer (PHY) Section
181
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 10-4. Page 0 (Port Status) Register Field Description
FIELD
Astat
SIZE
TYPE
2
Rd
DESCRIPTION
TPA line state. This field indicates the instantaneous TPA line state of the selected port,
encoded as:
Code
11
10
01
00
Arbitration Value
Z
1
0
Invalid
Bstat
2
Rd
TPB line state. This field indicates the TPB line state of the selected port. This field has the
same encoding as the Astat field.
Ch
1
Rd
Child/parent status. A 1 indicates that the selected port is a child port. A 0 indicates that the
selected port is the parent port. A disconnected, disabled, or suspended port is reported as a
child port. The Ch bit is invalid after a bus reset until tree-ID has completed.
Con
1
Rd
Debounced port connection status. This bit indicates that the selected port is connected. The
connection must be stable for the debounce time of approximately 341 ms for the Con bit to
be set to 1. The Con bit is reset to 0 by hardware reset and is unaffected by bus reset.
Note: The Con bit indicates that the port is physically connected to a peer PHY, but this does
not necessarily mean that the port is active. For IEEE Std 1394b-2002-coupled connections,
the Con bit is set when a port detects connection tones from the peer PHY and
operating-speed negotiation is completed.
RxOK
1
Rd
Receive OK. In IEEE Std 1394a-2000 mode, this bit indicates the reception of a debounced
TPBias signal. In beta mode, this bit indicates the reception of a continuous electrically valid
signal.
Note: RxOK is set to false during the time that only connection tones are detected in beta
mode.
Dis
1
RdWr
Port disabled control. If this bit is 1, the selected port is disabled. The Dis bit is reset to 0 by
hardware reset (all ports are enabled for normal operation following hardware reset). The Dis
bit is not affected by bus reset. When this bit is set, the port cannot become active; however,
the port still tones, but does not establish an active connection.
Negotiated_speed
1
Rd
Negotiated speed. Indicates the maximum speed negotiated between this port and its
immediately connected port. The encoding is as for Max_port_speed. It is set on connection
when in beta mode, or to a value established during self-ID when in IEEE Std 1394a-2000
mode.
PIE
1
RdWr
Port event interrupt enable. When this bit is 1, a port event on the selected port sets the port
event interrupt (PEI) bit and notifies the link. This bit is reset to 0 by a hardware reset and is
unaffected by bus reset.
Fault
1
Rd/Wr
Fault. This bit indicates that a resume-fault or suspend-fault has occurred on the selected
port, and that the port is in the suspended state. A resume-fault occurs when a resuming port
fails to detect incoming cable bias from its attached peer. A suspend-fault occurs when a
suspending port continues to detect incoming cable bias from its attached peer. Writing 1 to
this bit clears the Fault bit to 0. This bit is reset to 0 by hardware reset and is unaffected by
bus reset.
Standby_fault
1
Rd/Wr
Standby fault. This bit is set to 1 if an error is detected during a standby operation and cleared
on exit from the standby state. A write of 1 to this bit or receipt of the appropriate remote
command packet clears it to 0. When this bit is cleared, standby errors are cleared.
Disscrm
1
Rd/Wr
Disable scrambler. If this bit is set to 1, the data sent during packet transmission is not
scrambled.
B_Only
1
Rd
Beta-mode operation only. For the XIO2213B, this bit is set to 0 for all ports.
DC_connected
1
Rd
If this bit is set to 1, the port has detected a dc connection to the peer port by means of an
IEEE Std 1394a-2000-style connect-detect circuit.
182
Physical Layer (PHY) Section
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Table 10-4. Page 0 (Port Status) Register Field Description (continued)
SIZE
TYPE
DESCRIPTION
Max_port_speed
FIELD
3
Rd/Wr
Maximum port speed. The maximum speed at which a port is allowed to operate in beta
mode. The encoding is:
000 = S100
001 = S200
010 = S400
011 = S800
100 = S1600
101 = S3200
110 = Reserved
111 = Reserved
An attempt to write to the register with a value greater than the hardware capability of the port
results in the value for the maximum speed of which the port is capable being stored in the
register. The port uses this register only when a new connection is established in the beta
mode. The power reset value is the maximum speed capable of the port. Software can modify
this value to force a port to train at a lower than maximum, but no lower than minimum speed.
LPP
1
Rd
Local plug present. This flag is set permanently to 1.
Cable_speed
3
Rd
Cable speed. This variable is set to the value for the maximum speed that the port is capable
of. The encoding is the same as for Max_port_speed.
Connection_unreliable
1
Rd/Wr
Beta_mode
1
Rd
Operating in beta mode. If this bit is 1, the port is operating in beta mode; it is equal to 0
otherwise (that is, when operating in IEEE Std 1394a-2000 mode, or when disconnected). If
Con is 1, RxOK is 1, and Beta_mode is 0, the port is active and operating in the IEEE Std
1394a-2000 mode.
Port_error
8
Rd/Wr
Port error. Incremented whenever the port receives an invalid codeword, unless the value is
already 255. Cleared when read (including being read by means of a remote access packet).
Intended for use by a single bus-wide diagnostic program.
Loop_disable
1
Rd
Loop disable. This bit is set to 1 if the port has been placed in the loop-disable state as part of
the loop-free build process (the PHYs at either end of the connection are active, but if the
connection itself were activated, a loop would exist). Cleared on bus reset and on
disconnection.
In_standby
1
Rd
In standby. This bit is set to 1 if the port is in standby power-management state.
Hard_disable
1
Rd/Wr
Connection unreliable. If this bit is set to 1, a beta-mode speed negotiation has failed or
synchronization has failed. A write of 1 to this field resets the value to 0.
Hard disable. No effect unless the port is disabled. If this bit is set to 1, the port does not
maintain connectivity status on an ac connection when disabled. The values of the Con and
RxOK bits are forced to 0. This flag can be used to force renegotiation of the speed of a
connection. It can also be used to place the device into a lower-power state because when
hard disabled, a port no longer tones to maintain IEEE Std 1394b-2002 ac-connectivity status.
The vendor ID page identifies the vendor/manufacturer and compliance level. The page is selected by
writing 1 to the Page_Select field in base register 7. Table 10-5 shows the configuration of the vendor ID
page, and Table 10-6 shows the corresponding field descriptions.
Table 10-5. Page 1 (Vendor ID) Register Configuration
ADDRESS
BIT POSITION
0
1000
1
2
3
4
1001
Reserved
1010
Vendor_ID[0]
1011
Vendor_ID[1]
1100
Vendor_ID[2]
1101
Product_ID[0]
1110
Product_ID[1]
1111
Product_ID[2]
Submit Documentation Feedback
5
6
7
Compliance
Physical Layer (PHY) Section
183
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
Table 10-6. Page 1 (Vendor ID) Register Field Descriptions
SIZE
TYPE
Compliance
FIELD
8
Rd
Compliance level. For the XIO2213B, this field is 02h, indicating compliance with the IEEE Std
1394b-2002 specification.
Vendor_ID
24
Rd
Manufacturers organizationally unique identifier (OUI). For the XIO2213B, this field is 08 0028h (TI)
(the MSB is at register address 1010b).
Product_ID
24
Rd
Product identifier. For the XIO2213B, this field is 83_13_07h.
184
DESCRIPTION
Physical Layer (PHY) Section
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
The vendor dependent page provides access to the special control features of the XIO2213B, as well as
configuration and status information used in manufacturing test and debug. This page is selected by
writing 7 to the Page_Select field in base register 7. Table 10-7 shows the configuration of the vendor
dependent page, and Table 10-8 shows the corresponding field descriptions.
Table 10-7. Page 7 (Vendor Dependent) Register Configuration
BIT POSITION
ADDRESS
0
1
2
3
4
1000
Reserved
1001
Reserved for test
1010
Reserved for test
1011
Reserved for test
1100
Reserved for test
1101
5
6
7
Reserved for test
1110
SWR
Reserved for test
1111
Reserved for test
Table 10-8. Page 7 (Vendor Dependent) Register Field Descriptions
FIELD
SWR
SIZE
1
TYPE
Description
Rd/Wr Software hard reset. Writing a 1 to this bit forces a hard reset of the PHY section (same effect as momentarily
asserting the RESET terminal low). This bit is always read as a 0.
10.2 PHY Section Application Information
10.2.1 Power Class Programming
The PC0–PC2 terminals are programmed to set the default value of the power class indicated in the pwr
field (bits 21–23) of the transmitted self-ID packet. Descriptions of the various power classes are given in
Table 10-9. The default power-class value is loaded following a hardware reset, but is overridden by any
value subsequently loaded into the Pwr_Class field in register 4.
Table 10-9. Power Class Register Description
PC[0:2]
DESCRIPTION
000
Node does not need power and does not repeat power.
001
Node is self powered and provides a minimum of 15 W to the bus.
010
Node is self powered and provides a minimum of 30 W to the bus.
011
Node is self powered and provides a minimum of 5 W to the bus.
100
Node may be powered from the bus and is using up to 3 W; no additional power is needed to enable the link. The node may
also provide power to the bus. The amount of bus power that it provides can be found in the configuration ROM.
101
Reserved for future standardization
110
Node is powered from the bus and uses up to 3 W. An additional 3 W is needed to enable the link.
111
Node is powered from the bus and uses up to 3 W. An additional 7 W is needed to enable the link.
Submit Documentation Feedback
Physical Layer (PHY) Section
185
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
10.2.2 Power-Up Reset
To ensure proper operation of the XIO2213B PHY section, the RESET terminal must be asserted low for a
minimum of 2 ms from the time that DVDD, AVDD, and PLLVDD power reaches the minimum required
supply voltage and the input clock is valid. If a fundamental-mode crystal is used rather than an oscillator,
the start-up time parameter may be set to zero. When using a passive capacitor on the RESET terminal to
generate a power-on-reset signal, the minimum reset time is ensured if the value of the capacitor satisfies
the following equation (the value must be no smaller than approximately 0.1 µF):
Cmin = (0.0077 T) + 0.085 + (external_oscillator_start-up_time 0.05)
Where:
Cmin = Minimum capacitance on RESET terminal (F)
T = VDD ramp time, 10% to 90% (ms)
external_oscillator_start-up_time = Time from power applied to external oscillator until oscillator outputs a
valid clock (ms)
10.2.3 Crystal Oscillator Selection
The XIO2213B is designed to use an external 98.304-MHz crystal oscillator connected to the XI terminal
to provide the reference clock. This clock, in turn, drives a PLL circuit that generates the various clocks
required for transmission and resynchronization of data at the S100 through S800 media data rates.
A variation of less than ±100 ppm from nominal for the media data rates is required by IEEE Std 1394.
Adjacent PHYs may, therefore, have a difference of up to 200 ppm from each other in their internal clocks,
and PHYs must be able to compensate for this difference over the maximum packet length. Larger clock
variations can cause resynchronization overflows or underflows, resulting in corrupted packet data.
For the XIO2213B, the PCLK output can be used to measure the frequency accuracy and stability of the
internal oscillator and PLL from which it is derived. The frequency of the PCLK output must be within ±100
ppm of the nominal frequency of 98.304 MHz.
The following are some typical specifications for an oscillator used with the XIO2213B, in order to achieve
the required frequency accuracy and stability:
• RMS jitter of 5 ps or less
• RMS phase-noise jitter of 1 ps or less over the range 12 kHz to 20 MHz or higher
• Frequency tolerance at 25°C: Total frequency variation for the complete circuit is ±100 ppm. A device
with ±30-ppm or ±50-ppm frequency tolerance is recommended for adequate margin.
• Frequency stability (over temperature and age): A device with ±30-ppm or ±50-ppm frequency stability
is recommended for adequate margin.
The total frequency variation must be kept below ±100 ppm from nominal, with some allowance for
error introduced by board and device variations. Trade-offs between frequency tolerance and stability
may be made, as long as the total frequency variation is less than ±100 ppm. For example, the
frequency tolerance of the crystal may be specified at 50 ppm and the temperature tolerance may be
specified at 30 ppm to give a total of 80-ppm possible variation due to the oscillator alone. Aging also
contributes to the frequency variation. It is strongly recommended that part of the verification process
for the design is to measure the frequency of the PCLK output of the PHY section. This should be
done using a frequency counter with an accuracy of six digits or better.
186
Physical Layer (PHY) Section
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
10.2.4 Bus Reset
It is recommended that whenever the user has a choice, the user should initiate a bus reset by writing to
the initiate short bus reset (ISBR) bit (bit 1, PHY register 0101b). Care must be taken not to change the
value of any of the other writeable bits in this register when the ISBR bit is written to.
In the XIO2213B, the initiate bus reset (IBR) bit can be set to 1 in order to initiate a bus reset and
initialization sequence; however, it is recommended to use the ISBR bit instead. The IBR bit is located in
PHY register 1 along with the root holdoff bit (RHB) and gap count. As required by the IEEE Std
1394b-2002 Supplement, this configuration maintains compatibility with older TI PHY designs that were
based on either the suggested register set defined in Annex J of IEEE Std 1394-1995 or the IEEE Std
1394a-2000 Supplement. Therefore, whenever the IBR bit is written, the RHB and gap count are also
necessarily written.
It is recommended that the RHB and gap count only be updated by PHY configuration packets. The
XIO2213B is IEEE Std 1394a-2000 and IEEE Std 1394b-2002 compliant and, therefore, both the reception
and transmission of PHY configuration packets cause the RHB and gap count to be loaded, unlike older
IEEE Std 1394-1995-compliant PHYs that decode only received PHY configuration packets.
The gap count is set to the maximum value of 63 after two consecutive bus resets without an intervening
write to the gap count, either by a write to PHY register 1 or by a PHY configuration packet. This
mechanism allows a PHY configuration packet to be transmitted and then a bus reset initiated to verify
that all nodes on the bus have updated their RHBs and gap counts, without having the gap count set back
to 63 by the bus reset. The subsequent connection of a new node to the bus, which initiates a bus reset,
then causes the gap count of each node to be set to 63. Note, however, that if a subsequent bus reset is
instead initiated by a write to register 1 to set the IBR bit, all other nodes on the bus have their gap counts
set to 63, while this nodes gap count remains set to the value just loaded by the write to PHY register 1.
Therefore, in order to maintain consistent gap counts throughout the bus, the following rules apply to the
use of the IBR bit, RHB, and gap count in PHY register 1:
• Following the transmission of a PHY configuration packet, a bus reset must be initiated in order to
verify that all nodes have correctly updated their RHBs and gap counts, and to ensure that a
subsequent new connection to the bus causes the gap count to be set to 63 on all nodes in the bus. If
this bus reset is initiated by setting the IBR bit to 1, the RHB and gap count register must also be
loaded with the correct values consistent with the just-transmitted PHY configuration packet. In the
XIO2213B, the RHB and gap count have been updated to their correct values on the transmission of
the PHY configuration packet, so these values can first be read from register 1 and then rewritten.
• Other than to initiate the bus reset that must follow the transmission of a PHY configuration packet,
when the IBR bit is set to 1 in order to initiate a bus reset, the gap count must also be set to 63 to be
consistent with other nodes on the bus, and the RHB must be maintained with its current value.
• The PHY register 1 must not be written to except to set the IBR bit. The RHB and gap count must not
be written without also setting the IBR bit to 1.
• To avoid these problems, all bus resets initiated by software must be initiated by writing the ISBR bit
(bit 1 PHY register 0101b). Care must be taken to not change the value of any of the other writeable
bits in this register when the ISBR bit is written to. Also, the only means to change the gap count of
any node must be by means of the PHY configuration packet, which changes all nodes to the same
gap count.
Submit Documentation Feedback
Physical Layer (PHY) Section
187
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
11
www.ti.com
Electrical Characteristics
Absolute Maximum Ratings (1)
11.1
over operating temperature range (unless otherwise noted)
VALUE
UNIT
Supply voltage range
DVDD_33, VDDA_33, VDDA_33, VDDPLL_33, VDD_33_COMB,
VDD_33_COMBIO
0.3 to 3.6
V
VSUP_15
Supply voltage range
VDD_15, VDDA_15, VPP, VDDPLL, VDD_15_COMB
0.5 to 1.65
V
VCORE_19
Supply voltage range
PLLVDD_CORE, DVDD_CORE
0.5 to 2.05
V
VSUP_33
5
VI
Input voltage range
VO
Output voltage range
PCIe (RX)
0.5 to VSUP_33 + 0.5
PCIe REFCLK (single ended)
0.5 to VSUP_15 + 0.5
PCIe REFCLK (differential)
0.5 to VSUP_33 + 0.5
Miscellaneous 3.3-V I/O
0.5 to VSUP_33 + 0.5
PHY interface
0.5 to VSUP_33 + 0.5
PCIe (TX)
0.5 to VSUP_15 + 0.5
Miscellaneous 3.3-V I/O
0.5 to VSUP_33 + 0.5
PHY interface
0.5 to VSUP_33 + 0.5
Input clamp current (VI < 0 or VI > VDD) (2)
Output clamp current (VO < 0 or VO > VDD)
Tstg
(1)
(2)
(3)
mA
20
mA
-65 to 150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Applies for external input and bidirectional buffers. VI < 0 or VI > VDD or VI > VCCP
Applies for external input and bidirectional buffers. VO < 0 or VO > VDD or VO > VCCP
11.2
Recommended Operating Conditions
OPERATION
MIN
NOM
MAX
UNIT
1.5 V
1.35
1.5
1.65
V
3.3
3.6
V
1.95
2.05
V
25
70
°C
25
105
VSUP_15
Supply voltage
VSUP_33
Supply voltage (I/O)
3.3 V
3
VCORE_195
Supply voltage
1.95 V
1.85
TA
Operating ambient temperature
0
TJ
Junction temperature
0
θJA
Junction-to-free-air thermal resistance
188
V
20
(3)
Storage temperature range
V
Electrical Characteristics
°C
Low K JEDEC
test board, 1s, no
air flow - ZAY
85
°C/W
Low K JEDEC
test board, 1s, no
air flow - ZAJ
88
°C/W
High K JEDEC
test board, 2s2p
no air flow - ZAY
65
°C/W
High K JEDEC
test board, 2s2p
no air flow - ZAJ
42.1
°C/W
High K JEDEC
test board, 2s2p
200 LFM - ZAY
52
°C/W
High K JEDEC
test board, 2s2p
200 LFM - ZAJ
33
°C/W
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Recommended Operating Conditions (continued)
OPERATION
θJC
Junction-to-case thermal resistance
θJB
Junction-to-board thermal resistance
ΨJT
Junction-to-top of package
ΨJB
Junction-to-board
11.3
MIN
NOM
MAX
UNIT
Cu cold plate
measurement
process - ZAY
13
°C/W
Cu cold plate
measurement
process - ZAJ
13
°C/W
EIA/JESD 51-8
ZAY
35
°C/W
EIA/JESD 51-8
ZAJ
27
°C/W
EIA/JESD 51-2
ZAY
0.1
°C/W
EIA/JESD 51-2
ZAJ
0.13
°C/W
EIS/JESD 51-6
ZAY
29.7
°C/W
EIS/JESD 51-6
ZAJ
22.1
°C/W
PCIe Differential Transmitter Output Ranges
TXP and TXN
PARAMETER
MIN
UI
Unit interval
VTX-DIFFp-p
Differential peak-to-peak
output voltage
0.8
VTX-DE-RATIO
Deemphasized differential
output voltage (ratio)
3.0
TTX-EYE
Minimum TX eye width
TTX-EYE-MEDIAN-to-MAX-JITTER
Maximum time between
jitter median and maximum
deviation from the median
TTX-RISE
TTX-FALL
P/N TX output rise/fall time
VTX-CM-ACp
RMS ac peak
common-mode output
voltage
VTX-CM-DC-ACTIVE-IDLE-DELTA
Absolute delta of dc
common-mode voltage
during L0 and electrical idle
VTX-CM-DC-LINE-DELTA
VTX-IDLE-DIFFp
(1)
(2)
(3)
(4)
399.88
NOM
400
3.5
MAX
UNIT
COMMENTS
400.12
ps
Each UI is 400 ps 300 ppm. UI does not account for
SSC dictated variations. (1)
1.2
V
VTX-DIFFp-p = 2*|VTXP - VTXN| (2)
4.0
dB
This is the ratio of the VTX-DIFFp-p of the second and
following bits after a transition divided by the
VTX-DIFFp-p of the first bit after a transition. (2)
UI
The maximum transmitter jitter can be derived as
TTXMAX- JITTER = 1 – TTX-EYE = 0.3 UI.(2) (3)
UI
Jitter is defined as the measurement variation of the
crossing points (VTX-DIFFp-p = 0 V) in relation to
recovered TX UI. A recovered TX UI is calculated
over 3500 consecutive UIs of sample data. Jitter is
measured using all edges of the 250 consecutive
UIs in the center of the 3500 UIs used for
calculating the TX UI.(2)(3)
UI
(2) (4)
0.75
0.15
0.125
20
mV
VTX-CM-ACp = RMS(|VTXP + VTXN|/2 VTX-CM-DC)
VTX-CM-DC = DC(avg) of |VTXP + VTXN|/2(2)
0
100
mV
|VTX-CM-DC VTX-CM-Idle-DC| 100 mV VTX-CM-DC = DC(avg)
of |VTXP + VTXN|/2 [during L0]
VTX-CM-Idle-DC = DC(avg) of |VTXP + VTXN|/2 (during
electrical idle)(2)
Absolute delta of dc
common-mode voltage
between P and N
0
25
mV
|VTXP-CM-DC VTXN-CM-DC| 25 mV when
VTXP-CM-DC = DC(avg) of |VTXP|
VTXN-CM-DC = DC(avg) of |VTXN|(2)
Electrical idle differential
peak output voltage
0
20
mV
VTX-IDLE-DIFFp = |VTXP-Idle VTXN-Idle| 20 mV(2)
No test load is necessarily associated with this value.
Specified at the measurement point into a timing and voltage compliance test load and measured over any 250 consecutive TX UIs.
A TTX-EYE = 0.75 UI provides for a total sum of deterministic and random jitter budget of TTX-JITTER-MAX = 0.25 UI for the transmitter
collected over any 250 consecutive TX UIs. The TTX-EYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in which the median
and the maximum deviation from the median is less than half of the total TX jitter budget collected over any 250 consecutive TX UIs. It
must be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter
points on either side is approximately equal as opposed to the averaged time value.
Measured between 20% and 80% at transmitter package terminals into a test load for both VTXP and VTXN.
Submit Documentation Feedback
Electrical Characteristics
189
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
www.ti.com
PCIe Differential Transmitter Output Ranges (continued)
TXP and TXN
PARAMETER
MIN
VTX-RCV-DETECT
Amount of voltage change
allowed during receiver
detection
VTX-DC-CM
TX dc common-mode
voltage
ITX-SHORT
TX short-circuit current limit
TTX-IDLE-MIN
Minimum time spent in
electrical idle
TTX-IDLE-SET-to-IDLE
Maximum time to transition
to a valid electrical idle after
sending an electrical idle
ordered set
TTX-IDLE-to-DIFF-DATA
Maximum time to transition
to valid TX specifications
after leaving an electrical
idle condition
RLTX-DIFF
Differential return loss
RLTX-CM
Common-mode return loss
ZTX-DIFF-DC
DC differential TX
impedance
80
ZTX-DC
Transmitter dc impedance
40
CTX
AC coupling capacitor
75
(5)
190
NOM
MAX
UNIT
COMMENTS
The total amount of voltage change that a
transmitter can apply to sense whether a low
impedance receiver is present
600
mV
3.6
V
The allowed dc common-mode voltage under any
condition
90
mA
The total current the transmitter can provide when
shorted to its ground
UI
Minimum time a transmitter must be in electrical
Idle. Utilized by the receiver to start looking for an
electrical idle exit after successfully receiving an
electrical idle ordered set.
UI
After sending an electrical idle ordered set, the
transmitter must meet all electrical idle
specifications within this time. This is considered a
debounce time for the transmitter to meet electrical
idle after transitioning from L0.
UI
Maximum time to meet all TX specifications when
transitioning from electrical idle to sending
differential data. This is considered a debounce time
for the TX to meet all TX specifications after leaving
electrical idle.
10
dB
Measured over 50 MHz to 1.25 GHz (5)
6
dB
Measured over 50 MHz to 1.25 GHz(5)
Ω
TX dc differential mode low impedance
Ω
Required TXP as well as TXN dc impedance during
all states
nF
All transmitters are ac coupled and are required on
the PWB.
0
50
20
20
100
120
200
The transmitter input impedance results in a differential return loss greater than or equal to 12 dB and a common-mode return loss
greater than or equal to 6 dB over a frequency range of 50 MHz to 1.25 GHz. This input impedance requirement applies to all valid input
levels. The reference impedance for return loss measurements is 50 to ground for both the P and N lines. Note that the series
capacitors CTX is optional for the return loss measurement.
Electrical Characteristics
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
11.4
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
PCIe Differential Receiver Input Ranges
RXP and RXN
PARAMETER
UI
Unit interval
VRX-DIFFp-p
Differential input peak-to-peak
voltage
TRX-EYE
Minimum receiver eye width
MIN
399.88
NOM
400
0.175
MAX
UNIT
COMMENTS
400.12
ps
Each UI is 400 ps 300 ppm. UI does not account
for SSC dictated variations (1)
1.200
V
VRX-DIFFp-p = 2*|VRXP VRXN, | (2)
0.4
UI
The maximum interconnect media and transmitter
jitter that can be tolerated by the receiver is
derived as TRX-MAX-JITTER = 1 TRX-EYE = 0.6 UI (2)
(3)
TRX-EYE-MEDIAN-to-MAX-JITTER
Maximum time between jitter
median and maximum
deviation from median
0.3
UI
Jitter is defined as the measurement variation of
the crossing points (VRX-DIFFp-p = 0 V) in relation
to recovered TX UI. A recovered TX UI is
calculated over 3500 consecutive UIs of sample
data. Jitter is measured using all edges of the
250 consecutive UIs in the center of the 3500 UIs
used for calculating the TX UI. (2) (3)
VRX-CM-ACp
AC peak common-mode input
voltage
150
mV
VRX-CM-ACp = RMS(|VRXP + VRXN|/2 VRX-CM-DC)
VRX-CM-DC = DC(avg) of |VRXP + VRXN|/2 (2)
RLRX-DIFF
Differential return loss
10
dB
Measured over 50 MHz to 1.25 GHz with the P
and N lines biased at +300 mV and 300 mV,
respectively (4)
RLRX-CM
Common-mode return loss
6
dB
Measured over 50 MHz to 1.25 GHz with the P
and N lines biased at +300 mV and 300 mV,
respectively (4)
ZRX-DIFF-DC
DC differential input
impedance
80
100
120
Ω
RX dc differential mode impedance(4)
ZRX-DC
DC input impedance
40
50
60
Ω
Required RXP as well as RXN dc impedance (50
}20% tolerance)(2) (5)
ZRX-HIGH-IMP-D
Powered down dc input
impedance
k
Required RXP as well as RXN dc impedance
when the receiver terminations do not have
power (6)
VRX-IDLE-DET-DIFFp-p
Electrical idle detect threshold
TRX-IDLE-DET-DIFF-ENTER-TIME
Unexpected electrical idle
enter detect threshold
integration time
(1)
(2)
(3)
(4)
(5)
(6)
200
65
175
10
mV
VRX-IDLE-DET-DIFFp-p = 2*|VRXP VRXN| measured at
the receiver package terminals
ms
An unexpected electrical idle
(VRX-DIFFp-p < VRX-IDLE-DET-DIFFp-p) must be
recognized no longer than
TRX-IDLE-DET-DIFF-ENTER-TIME to signal an
unexpected idle condition.
No test load is necessarily associated with this value.
Specified at the measurement point and measured over any 250 consecutive UIs. A test load must be used as the RX device when
taking measurements. If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500
consecutive UI is used as a reference for the eye diagram.
A TRX-EYE = 0.40 UI provides for a total sum of 0.60 UI deterministic and random jitter budget for the transmitter and interconnect
collected any 250 consecutive UIs. The TRX-EYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in which the median and the
maximum deviation from the median is less than half of the total UI jitter budget collected over any 250 consecutive TX UIs. It must be
noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on
either side is approximately equal as opposed to the averaged time value. If the clocks to the RX and TX are not derived from the same
reference clock, the TX UI recovered from 3500 consecutive UIs must be used as the reference for the eye diagram.
The receiver input impedance results in a differential return loss greater than or equal to 15 dB with the P line biased to 300 mV and the
N line biased to 300 mV and a common-mode return loss greater than or equal to 6 dB (no bias required) over a frequency range of 50
MHz to 1.25 GHz. This input impedance requirement applies to all valid input levels. The reference impedance for return loss
measurements for is 50 to ground for both the P and N line (i.e., as measured by a vector network analyzer with 50- probes). The series
capacitors CTX is optional for the return loss measurement.
Impedance during all link training status state machine (LTSSM) states. When transitioning from a PCIe reset to the detect state (the
initial state of the LTSSM) there is a 5-ms transition time before receiver termination values must be met on the unconfigured lane of a
port.
The RX dc common-mode impedance that exists when no power is present or PCIe reset is asserted. This helps ensure that the
receiver detect circuit does not falsely assume a receiver is powered on when it is not. This term must be measured at 300 mV above
the RX ground.
Submit Documentation Feedback
Electrical Characteristics
191
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
11.5
www.ti.com
PCIe Differential Reference Clock Input Ranges (1)
REFCLK+ and REFCLK–
PARAMETER
MIN
NOM
MAX
UNIT
COMMENTS
fIN-DIFF
Differential input frequency
100
MHz
The input frequency is 100 MHz + 300 ppm and
2800 ppm including SSC-dictated variations.
fIN-SE
Single-ended input frequency
125
MHz
The input frequency is 125 MHz + 300 ppm and
300 ppm.
VRX-DIFFp-p
Differential input peak-to-peak
voltage
VIH-SE
0.175
1.200
V
VRX-DIFFp-p = 2*|VREFCLK+ VREFCLK–|R
REFCLK+ only
0.7 VDD_33
VDD_33
V
Single-ended, reference clock mode high-level
input voltage
VIL-SE
REFCLK+ only
0
0.3 VDD_33
V
Single-ended, reference clock mode low-level
input voltage
VRX-CM-ACp
AC peak common-mode input
voltage
Duty cycle
140
40%
mV
VRX-CM-ACp = RMS(|VREFCLK+ + VREFCLK–|/2
VRX-CM-DC) VRX-CM-DC = DC(avg) of
|VREFCLK+ + VREFCLK–|/2
Differential and single-ended waveform input duty
cycle
60%
ZRX-DIFF-DC
DC differential input impedance
20
k
REFCLK– dc differential mode impedance
ZRX-DC
DC input impedance
20
k
REFCLK+ dc single-ended mode impedance
(1)
The XIO2213B is compliant with the defined system jitter models for a PCIe reference clock and associated TX/RX link. These system
jitter models are described in the PCI Express Jitter Modeling, Revision 1.0 RD document. Any usage of the XIO2213B in a system
configuration that does not conform to the defined system jitter models requires the system designer to validate the system jitter
budgets.
11.6
Electrical Characteristics Over Recommended Operating Conditions (3.3-V I/O)
PERST, WAKE, REFCLK_SEL, GRST, GPIO[7:0], CNA, PC[2:0], and all RSVD terminals
PARAMETER
VIH
High-level input voltage
(1)
VIL
Low-level input voltage
(1)
VI
Input voltage
OPERATION
TEST CONDITIONS
MIN
MAX
UNIT
VDD_33
0.7 VDD_33
VDD_33
V
VDD_33
0
0.3 VDD_33
V
0
VDD_33
V
0
VDD_33
V
0
25
ns
0.3 VDD_33
V
(2)
VO
Output voltage
tT
Input transition time (trise and tfall)
Vhys
Input hysteresis (3)
VOH
High-level output voltage
VDD_33
IOH = 4 mA
VOL
Low-level output voltage
VDD_33
IOL = 4 mA
0.22 VDD_33
V
IOZ
High-impedance, output current(2)
VDD_33
VI = 0 to VDD_33
20
µA
IOZP
High-impedance, output current with internal
VDD_33
pullup or pulldown resistor (4)
VI = 0 to VDD_33
100
µA
II
Input current (5)
VI = 0 to VDD_33
1
µA
(1)
(2)
(3)
(4)
(5)
192
VDD_33
0.8 VDD_33
V
Applies to external inputs and bidirectional buffers
Applies to external outputs and bidirectional buffers
Applies to PERST and GRST
Applies to GRST (pullup resistor) and most GPIOs (pullup resistor)
Applies to external input buffers
Electrical Characteristics
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
11.7
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Electrical Characteristics Over Recommended Operating Conditions (PHY Port
Driver)
PARAMETER
TEST CONDITIONS
1394a differential output voltage
VOD
56 Figure 11-1
MIN
TYP
172
1394b differential output voltage
MAX
265
700
UNIT
mV
IDIFF
Driver difference current (TPA+, TPA–, TPB+,
TPB–)
Drivers enabled, speed signaling off
1.05 (1)
1.05 (1)
mA
ISP20
Common-mode speed signaling current (TPB+,
TPB–)
S200 speed signaling enabled
4.84 (2)
2.53 (2)
mA
Common-mode speed signaling current (TPB+,
TPB–)
S400 speed signaling enabled
12.4 (2)
8.1 (2)
mA
20
mV
0
ISP40
0
VOFF Off-state differential voltage
VCM
(1)
(2)
Drivers disabled
1394b common-mode voltage
1.5
V
Limits defined as algebraic sum of TPA+ and TPA– driver currents. Limits also apply to algebraic sum of TPB+ and TPB– driver
currents.
Limits defined as absolute limit of each of TPB+ and TPB– driver currents.
TPAx+
TPBx+
56 W
TPAxTPBx-
Figure 11-1. Test Load Diagram
11.8 Switching Characteristics for PHY Port Driver
MAX
UNIT
Jitter, transmit
PARAMETER
Between TPA and TPB
0.15
ns
Skew, transmit
Between TPA and TPB
0.1
ns
tr
TP differential rise time, transmit
10% to 90%, at 1394 connector
0.5
1.2
ns
tf
TP differential fall time, transmit
90% to 10%, at 1394 connector
0.5
1.2
ns
tsu
Setup time, CTL0, CTL1, D1-D7, LREQ until
PCLK - 1394a-2000
50% to 50%
2.5
ns
th
Hold time, CTL0, CTL1, D1-D7, LREQ after PCLK
- 1394a-2000
50% to 50%
0
ns
tsu
Setup time, CTL0, CTL1, D1-D7, LREQ until
PCLK - 1394b
50% to 50%
2.5
ns
th
Hold time, CTL0, CTL1, D1-D7, LREQ after PCLK
- 1394b
50% to 50%
1
ns
td
Delay time, PCLK until CTL0, CTL1, D1-D7, PINT
50% to 50%
0.5
Submit Documentation Feedback
TEST CONDITIONS
MIN
7
Electrical Characteristics
ns
193
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
11.9
www.ti.com
Electrical Characteristics Over Recommended Operating Conditions PHY Port
Receiver
PARAMETER
TEST CONDITIONS
MIN
TYP
4
7
MAX
UNIT
k
ZID
Differential impedance
Drivers disabled
ZIC
Common-mode impedance
Drivers disabled
24
pF
VTH-R
Receiver input threshold voltage
Drivers disabled
30
30
mV
VTH-CB
Cable bias detect threshold. TPBx
cable inputs
Drivers disabled
0.6
1
V
VTH+
Positive arbitration comparator
threshold voltage
Drivers disabled
89
168
mV
VTH
Negative arbitration comparator
threshold voltage
Drivers disabled
168
89
mV
4
pF
20
k
VTH-SP200 Speed signal threshold
TPBIAS-TPA common mode voltage, drivers disabled
49
131
mV
VTH-SP400 Speed signal threshold
TPBIAS-TPA common mode voltage, drivers disabled
314
396
mV
MAX
UNIT
11.10
Jitter/Skew Characteristics for 1394a PHY Port Receiver
PARAMETER
1394a Receive input jitter
1394a Receive input skew
11.11
MIN
TYP
TPA, TPB cable inputs, S100 operation
1.08
TPA, TPB cable inputs, S200 operation
0.5
TPA, TPB cable inputs, S400 operation
0.315
Between TPA and TPB cable inputs, S100 operation
0.8
Between TPA and TPB cable inputs, S200 operation
0.55
Between TPA and TPB cable inputs, S400 operation
0.5
ns
ns
Operating, Timing, and Switching Characteristics of XI
PARAMETER
VIH
High-level input voltage
VIL
Low-level input voltage
MIN
TYP
MAX
0.63 VDDA_33
V
0.33 VDDA_33
Input clock frequency
98.304
Input clock duty cycle
V
MHz
Input clock frequency tolerance
Input slew rate
UNIT
<100
ppm
0.2
4
V/ns
40%
60%
11.12 Electrical Characteristics Over Recommended Operating Conditions
(1394a Miscellaneous I/O)
PARAMETER
VTH
Power status threshold CPS input
VO
TPBIAS output voltage
IO
TPBIAS output current
(1)
Measure at cable power side of resistor
194
Electrical Characteristics
TEST CONDITIONS
(1)
400-kΩ resistor
(1)
At rated IO current
MIN
MAX
4.7
7.5
1.665
2.015
5.6
1.3
UNIT
V
V
mA
Submit Documentation Feedback
XIO2213B
PCI Express™ TO 1394b OHCI WITH 3-PORT PHY
www.ti.com
12
SCPS210D – OCTOBER 2008 – REVISED JULY 2009
Glossary
ACRONYM
DEFINITION
BIST
Built-in self test
ECRC
End-to-end cyclic redundancy code
EEPROM
Electrically erasable programmable read-only memory
GP
General purpose
GPIO
General-purpose input/output
ID
Identification
IF
Interface
IO
Input/output
I2S
Inter IC sound
LPM
Link power management
LSB
Least significant bit
MSB
Most significant bit
MSI
Message signaled interrupts
PCI
Peripheral component interface
PME
PCI power-management event
QoS
Quality of service
RX
Receive
SCL
Serial-bus clock
SDA
Serial-bus data
TC
Traffic class
TLP
Transaction layer packet or protocol
TX
Transmit
VC
Virtual channel
WRR
Weighted round-robin
Submit Documentation Feedback
Glossary
195
PACKAGE OPTION ADDENDUM
www.ti.com
3-Aug-2009
PACKAGING INFORMATION
Orderable Device
Status (1)
Package
Type
Package
Drawing
Pins Package Eco Plan (2)
Qty
XIO2213BZAJ
ACTIVE
BGA
ZAJ
168
260
Green (RoHS &
no Sb/Br)
SNAGCU
Level-3-260C-168 HR
XIO2213BZAY
ACTIVE
NFBGA
ZAY
167
160
Green (RoHS &
no Sb/Br)
SNAGCU
Level-3-260C-168 HR
Lead/Ball Finish
MSL Peak Temp (3)
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
Logic
Power Mgmt
Microcontrollers
RFID
RF/IF and ZigBee® Solutions
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/lprf
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
Telephony
Video & Imaging
Wireless
www.ti.com/audio
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated