ETC 3D3215

3D3215
data 3 
delay
devices, inc.
MONOLITHIC 5-TAP 3.3V
FIXED DELAY LINE
(SERIES 3D3215)
FEATURES
•
•
•
•
•
•
•
•
•
•
•
PACKAGES
All-silicon, low-power 3.3V CMOS technology
Vapor phase, IR and wave solderable
Auto-insertable (DIP pkg.)
Low ground bounce noise
Leading- and trailing-edge accuracy
Delay range: 1.5ns through 300ns
Total delay tolerance: 2% or 0.5ns (3.3V, 25C)
Temperature stability: ±1% typical (0C-70C)
Vdd stability: ±1% typical (3.0V-3.6V)
Static Idd: 1.3ma typical
Minimum input pulse width: 25% of total delay
IN
O2
O4
GND
1
2
3
4
8
7
6
5
VDD
O1
O3
O5
3D3215Z-xx
SOIC (150 Mil)
IN
1
8
VDD
O2
2
7
O1
O4
3
6
O3
GND
4
5
O5
3D3215M-xx
DIP (300 Mil)
For mechanical dimensions, click here.
For package marking details, click here.
FUNCTIONAL DESCRIPTION
PIN DESCRIPTIONS
The 3D3215 5-Tap Delay Line product family consists of fixed-delay
3.3V CMOS integrated circuits. Each package contains a single delay
line, tapped and buffered at 5 points spaced uniformly in time. Tap-totap (incremental) delay values can range from 1.5ns through 60ns. The
input is reproduced at the outputs without inversion, shifted in time as
per the user-specified dash number. The 3D3215 is 3.3V CMOScompatible and features both rising- and falling-edge accuracy.
IN
O1
O2
O3
O4
O5
VDD
GND
N/C
The all-CMOS 3D3215 integrated circuit has been designed as a
reliable, economic alternative to hybrid fixed delay lines. It is offered in a
standard 8-pin auto-insertable DIP and a space saving surface mount 8-pin SOIC.
Delay Line Input
Tap 1 Output (20%)
Tap 2 Output (40%)
Tap 3 Output (60%)
Tap 4 Output (80%)
Tap 5 Output (100%)
+3.3 Volts
Ground
No Connection
TABLE 1: PART NUMBER SPECIFICATIONS
DASH #
3D3215Z-xx
3D3215M-xx
-1.5
-2
-2.5
-3
-4
-5
-6
-8
-10
-12
-15
-20
-25
-30
-40
-50
-60
DELAY SPECIFICATIONS
TOTAL
TAP-TAP
DELAY (ns)
DELAY (ns)
6.0 ± 0.5*
1.5 ± 0.7
8.0 ± 0.5*
2.0 ± 0.8
10.0 ± 0.5*
2.5 ± 1.0
12.0 ± 0.5*
3.0 ± 1.3
16.0 ± 0.5*
4.0 ± 1.3
20.0 ± 0.5*
5.0 ± 1.4
24.0 ± 0.5*
6.0 ± 1.4
40.0 ± 0.8
8.0 ± 1.4
50.0 ± 1.0
10.0 ± 1.5
60.0 ± 1.2
12.0 ± 1.5
75.0 ± 1.5
15.0 ± 1.5
100 ± 2.0
20.0 ± 2.0
125 ± 2.5
25.0 ± 2.5
150 ± 3.0
30.0 ± 3.0
200 ± 4.0
40.0 ± 4.0
250 ± 5.0
50.0 ± 5.0
300 ± 6.0
60.0 ± 6.0
INPUT RESTRICTIONS
RECOMMENDED
ABSOLUTE
Max Freq
Min P.W.
Max Freq
Min P.W.
23.8 MHz
21.0 ns
83.3 MHz
6.00 ns
20.8 MHz
24.0 ns
83.3 MHz
6.00 ns
18.5 MHz
27.0 ns
66.7 MHz
7.50 ns
16.7 MHz
30.0 ns
55.6 MHz
9.00 ns
13.9 MHz
36.0 ns
50.0 MHz
10.00 ns
11.9 MHz
42.0 ns
40.0 MHz
12.50 ns
10.4 MHz
48.0 ns
55.6 MHz
9.00 ns
8.33 MHz
60.0 ns
41.7 MHz
12.00 ns
6.67 MHz
75.0 ns
40.0 MHz
12.50 ns
5.56 MHz
90.0 ns
33.3 MHz
15.00 ns
4.42 MHz
113 ns
26.7 MHz
18.75 ns
3.33 MHz
150 ns
20.0 MHz
25.00 ns
2.66 MHz
188 ns
16.0 MHz
31.25 ns
2.22 MHz
225 ns
13.3 MHz
37.50 ns
1.67 MHz
300 ns
10.0 MHz
50.00 ns
1.33 MHz
375 ns
8.0 MHz
62.50 ns
1.11 MHz
450 ns
6.7 MHz
75.00 ns
* Total delay referenced to Tap1 output; Input-to-Tap1 = 7.5ns ± 1.5ns
NOTE: Any dash number between 1.5 and 60 not shown is also available as standard
Doc #01014
12/3/01
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
 2001 Data Delay Devices
1
3D3215
APPLICATION NOTES
OPERATIONAL DESCRIPTION
The 3D3215 five-tap delay line architecture is
shown in Figure 1. The delay line is composed of
a number of delay cells connected in series.
Each delay cell produces at its output a replica of
the signal present at its input, shifted in time. The
delay cells are matched and share the same
compensation signals, which minimizes tap-to-tap
delay deviations over temperature and supply
voltage variations.
INPUT SIGNAL CHARACTERISTICS
The Frequency and/or Pulse Width (high or low)
of operation may adversely impact the specified
delay accuracy of the particular device. The
reasons for the dependency of the output delay
accuracy on the input signal characteristics are
varied and complex. Therefore a Recommended
Maximum and an Absolute Maximum operating
input frequency and a Recommended Minimum
and an Absolute Minimum operating pulse width
have been specified.
OPERATING FREQUENCY
The Absolute Maximum Frequency
specification, tabulated in Table 1, determines the
highest frequency of the delay line input signal
that can be reproduced, shifted in time at the
device output, with acceptable duty cycle
distortion.
The Recommended Maximum Frequency
specification determines the highest frequency of
the delay line input signal for which the output
IN O1
O2
25%
O3
25%
O4
25%
O5
delay accuracy is guaranteed. To guarantee the
Table 1 delay accuracy for input frequencies
higher than the Recommended Maximum
Frequency, the 3D3215 must be tested at the
user operating frequency. Therefore, to facilitate
production and device identification, the part
number will include a custom reference
designator identifying the intended frequency of
operation. The programmed delay accuracy of
the device is guaranteed, therefore, only at the
user specified input frequency. Small input
frequency variation about the selected frequency
will only marginally impact the programmed delay
accuracy, if at all. Nevertheless, it is strongly
recommended that the engineering staff at
DATA DELAY DEVICES be consulted.
OPERATING PULSE WIDTH
The Absolute Minimum Pulse Width (high or
low) specification, tabulated in Table 1,
determines the smallest Pulse Width of the delay
line input signal that can be reproduced, shifted in
time at the device output, with acceptable pulse
width distortion.
The Recommended Minimum Pulse Width
(high or low) specification determines the
smallest Pulse Width of the delay line input signal
for which the output delay accuracy tabulated in
Table 1 is guaranteed.
To guarantee the Table 1 delay accuracy for input
pulse width smaller than the Recommended
Minimum Pulse Width, the 3D3215 must be
tested at the user operating pulse width.
Therefore, to facilitate production and device
IN
25%
O1
20%
O2
20%
Temp & VDD
Compensation
O3
20%
O4
20%
O5
20%
Temp & VDD
Compensation
Dash numbers < 8
VDD
Dash numbers >= 8
GND
VDD
GND
Figure 1: 3D3215 Functional Diagram
Doc #01014
12/3/01
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
2
3D3215
APPLICATION NOTES (CONT’D)
The thermal coefficient is reduced to 200 PPM/C,
which is equivalent to a variation, over the 0C70C operating range, of ±1% or 0.25ns
(whichever is greater) from the 25C delay
settings. The power supply coefficient is reduced,
over the 3.0V-3.6V operating range, to ±1% or
1ns (whichever is greater) of the delay settings at
the nominal 3.3VDC power supply.
identification, the part number will include a
custom reference designator identifying the
intended frequency and duty cycle of operation.
The programmed delay accuracy of the device is
guaranteed, therefore, only for the user specified
input characteristics. Small input pulse width
variation about the selected pulse width will only
marginally impact the programmed delay
accuracy, if at all. Nevertheless, it is strongly
recommended that the engineering staff at
DATA DELAY DEVICES be consulted.
The temperature and power supply sensitivities
are based on the measured delay of Tap 5 with
respect to Tap 1. The sensitivity of the Input-toTap 1 delay will be somewhat higher, particularly
with the smaller dash numbers.
POWER SUPPLY AND
TEMPERATURE CONSIDERATIONS
It is essential that the power supply pin be
adequately bypassed and filtered. In addition,
the power bus should be of as low an
impedance construction as possible. Power
planes are preferred.
The delay of CMOS integrated circuits is strongly
dependent on power supply and temperature.
The monolithic 3D3215 delay line utilizes novel
and innovative compensation circuitry to minimize
the delay variations induced by fluctuations in
power supply and/or temperature.
DEVICE SPECIFICATIONS
TABLE 2: ABSOLUTE MAXIMUM RATINGS
PARAMETER
DC Supply Voltage
Input Pin Voltage
Input Pin Current
Storage Temperature
Lead Temperature
SYMBOL
VDD
VIN
IIN
TSTRG
TLEAD
MIN
-0.3
-0.3
-1.0
-55
MAX
7.0
VDD+0.3
1.0
150
300
UNITS
V
V
mA
C
C
NOTES
25C
10 sec
TABLE 3: DC ELECTRICAL CHARACTERISTICS
(0C to 70C, 3.0V to 3.6V)
PARAMETER
Static Supply Current*
High Level Input Voltage
Low Level Input Voltage
High Level Input Current
Low Level Input Current
High Level Output Current
SYMBOL
IDD
VIH
VIL
IIH
IIL
IOH
MIN
Low Level Output Current
IOL
Output Rise & Fall Time
T R & TF
*IDD(Dynamic) = 5 * CLD * VDD * F
where: CLD = Average capacitance load/tap (pf)
F = Input frequency (GHz)
Doc #01014
12/3/01
TYP
1.3
MAX
2.0
-0.1
-0.1
0.0
0.0
-8.0
0.8
0.1
0.1
-6.0
6.0
7.5
mA
2
ns
2.0
UNITS
mA
V
V
µA
µA
mA
NOTES
VDD = 3.6V
VIH = VDD
VIL = 0V
VDD = 3.0V
VOH = 2.4V
VDD = 3.0V
VOL = 0.4V
CLD = 5 pf
Input Capacitance = 10 pf typical
Output Load Capacitance (CLD) = 25 pf max
DATA DELAY DEVICES, INC.
3 Mt. Prospect Ave. Clifton, NJ 07013
3
3D3215
SILICON DELAY LINE AUTOMATED TESTING
TEST CONDITIONS
INPUT:
o
o
Ambient Temperature: 25 C ± 3 C
Supply Voltage (Vcc): 3.3V ± 0.1V
Input Pulse:
High = 3.3V ± 0.1V
Low = 0.0V ± 0.1V
Source Impedance:
50Ω Max.
Rise/Fall Time:
3.0 ns Max. (measured
between 0.6V and 2.4V )
Pulse Width:
PWIN = 1.5 x Total Delay
Period:
PERIN = 3.0 x Total Delay
OUTPUT:
Rload:
Cload:
Threshold:
10KΩ ± 10%
5pf ± 10%
1.5V (Rising & Falling)
Device
Under
Test
Digital
Scope
10KΩ
5pf
470Ω
NOTE: The above conditions are for test only and do not in any way restrict the operation of the device.
PRINTER
COMPUTER
SYSTEM
PULSE
GENERATOR
OUT
IN
TRIG
DEVICE UNDER
TEST (DUT)
REF
OUT1
OUT2
OUT3
OUT4
OUT5
IN
TRIG
DIGITAL SCOPE/
TIME INTERVAL COUNTER
Figure 2: Test Setup
PERIN
PWIN
tRISE
INPUT
SIGNAL
tFALL
VIH
2.4V
1.5V
0.6V
2.4V
1.5V
0.6V
tPLH
OUTPUT
SIGNAL
VIL
tPHL
VOH
1.5V
1.5V
VOL
Figure 3: Timing Diagram
Doc #01014
12/3/01
DATA DELAY DEVICES, INC.
Tel: 973-773-2299
Fax: 973-773-9672
http://www.datadelay.com
4