ICS MK2754

MK2754
Low Cost 54 MHz VCXO
I C R O C LOC K
Description
Features
The MK2754 is MicroClock’s lowest cost, low
jitter, high performance VCXO and PLL clock
synthesizer designed to replace expensive 54 MHz
VCXOs. The on-chip Voltage Controlled Crystal
Oscillator accepts a 0 to 3V input voltage to vary
the output clocks by ±100 ppm. Using
MicroClock’s patented VCXO and analog PhaseLocked Loop (PLL) techniques, the device uses an
inexpensive external 13.5 MHz pullable crystal
input to produce a 54 MHz output clock.
• Packaged in 8 pin narrow SOIC
• Uses an inexpensive 13.500 MHz external crystal
• On-chip VCXO (patented) with pull range of
200ppm (minimum)
• VCXO tuning voltage of 0 to 3V
• 25mA output drive capability at TTL levels
• Advanced, low power, sub-micron CMOS process
• 5V operating voltage
MicroClock manufactures the largest variety of
Set-Top Box and multimedia clock synthesizers
for all applications. If more clock outputs are
needed, see the MK2731 or MK277x family of
parts. Consult MicroClock to eliminate VCXOs,
crystals and oscillators from your board.
Block Diagram
VIN
X1
13.5 MHz
pullable
crystal
X2
Voltage
Controlled
Crystal
Oscillator
PLL/Clock
Synthesis
Circuitry
Output
Buffer
54MHz
1
Revision 011698
Printed 11/16/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 2754 B
MK2754
Low Cost 54 MHz VCXO
I C R O C LOC K
Pin Assignment
MK2754
X1
1
8
X2
VDD
2
7
GND
VIN
3
6
CLK
GND
4
5
VDD
8 pin (150 mil) SOIC
Pin Descriptions
Number
1
2
3
4
5
6
7
8
Name
X1
VDD
VIN
GND
VDD
CLK
GND
X2
Description
Crystal connection. Connect to a pullable 13.5 MHz crystal.
VDD. Connect to +5V.
Voltage input to VCXO. Zero to 3V analog input which controls the frequency of the VCXO.
Connect to ground.
VDD. Connect to +5V.
54 MHz clock output.
Connect to ground.
Crystal connection. Connect to a pullable 13.5 MHz crystal.
2
Revision 011698
Printed 11/16/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 2754 B
I C R O C LOC K
MK2754
Low Cost 54 MHz VCXO
Electrical Specifications
Parameter
Conditions
Minimum
Typical
Maximum
Units
7
VDD+0.5
70
260
150
V
V
°C
°C
°C
5.25
V
V
V
V
mA
mA
V
ABSOLUTE MAXIMUM RATINGS (note 1)
Supply voltage, VDD
Inputs and Clock Outputs
Ambient Operating Temperature
Soldering Temperature
Storage temperature
Referenced to GND
Referenced to GND
-0.5
0
Max of 10 seconds
-65
DC CHARACTERISTICS (VDD = 5.0V unless noted)
Operating Voltage, VDD
Output High Voltage, VOH
Output Low Voltage, VOL
Output High Voltage, VOH, CMOS level
Operating Supply Current, IDD
Short Circuit Current
VIN, VCXO control voltage
IOH=-25mA
IOL=25mA
IOH=-8mA
No Load
4.75
2.4
0.4
VDD-0.4
20
±100
0
3
AC CHARACTERISTICS (VDD = 5.0V unless noted)
Input Crystal Frequency
Input Crystal Accuracy
Output Clock Rise Time
Output Clock Fall Time
Output Clock Duty Cycle
Maximum Absolute Jitter, short term
54 MHz output pullability, note 2
Notes:
13.50000
0.8 to 2.0V
2.0 to 0.8V
At 1.4V
0V ≤ VIN ≤ 3V
40
±100
50
200
±30
1.5
1.5
60
MHz
ppm
ns
ns
%
ps
ppm
1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged
exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability.
2. With a MicroClock approved pullable crystal.
External Components
The MK2754 requires a minimum number of external components for proper operation. A decoupling
capacitor of 0.1µF should be connected between VDD and GND on pins 2 and 4, as close to the MK2754
as possible. A series termination resistor of 33Ω may be used for the clock output. The input crystal must be
connected as close to the chip as possible. The input crystal should be a parallel mode, pullable, AT cut,
13.5MHz, with 14pF load capacitance. Consult MicroClock for recommended suppliers. IMPORTANT read application note MAN05 before laying out the PCB.
3
Revision 011698
Printed 11/16/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 2754 B
MK2754
Low Cost 54 MHz VCXO
I C R O C LOC K
Package Outline and Package Dimensions
8 pin SOIC
E
Symbol
A
b
D
E
H
e
h
Q
H
Pin 1
h x 45°
D
Inches
Min
Max
0.055 0.070
0.013 0.019
0.185 0.200
0.150 0.160
0.225 0.245
.050 BSC
0.015
0.004
0.01
Millimeters
Min
Max
1.397
1.778
0.330
0.483
4.699
5.080
3.810
4.064
5.715
6.223
1.27 BSC
0.381
0.102
0.254
A
Q
c
e
b
Ordering Information
Part/Order Number
MK2754S
MK2754STR
CHANGE HISTORY
Version Date first published
A
12/12/96
B
1/16/98
Marking
MK2754S
MK2754S
Status
Advance
Final
Shipping packaging
tubes
tape and reel
Package
8 pin SOIC
8 pin SOIC
Temperature
0-70°C
0-70°C
Comments
Original
Updated pkg height.
While the information presented herein has been checked for both accuracy and reliability, MicroClock Incorporated assumes no responsibility for either its use or for the
infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in
normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements
are not recommended without additional processing by MicroClock. MicroClock reserves the right to change any circuitry or specifications without notice. MicroClock does not
authorize or warrant any MicroClock product for use in life support devices or critical medical instruments.
4
Revision 011698
Printed 11/16/00
MicroClock Division of ICS•1271 Parkmoor Ave.•San Jose•CA•95126•(408)295-9800tel•(408)295-9818fax
MDS 2754 B