PRELIMINARY INFORMATION MK74CB217 Dual 1 to 8 Buffalo™ Clock Driver Description Features The MK74CB217 Buffalo™ is a monolithic CMOS high speed clock driver. It consists of two identical single input to eight low-skew output, non-inverting clock drivers. This eliminates concerns of part to part matching in many systems. The MK74CB217 is packaged in the tiny 28 pin SSOP, which uses the same board space as the narrow 16 pin SOIC. The inputs can be connected together for a 1 to 16 fanout buffer. • Tiny 28 pin SSOP (150 mil) package • Dual one input to eight output clock drivers • Outputs are skew matched to within 250 ps • A outputs and B outputs matched to 250 ps • 3.3 V or 5 V supply voltage • Output Enable tri-states each bank of eight • Clock speeds up to 200 MHz Family of ICS Parts A quad 1 to 4, and PECL versions, are also available. Consult us for more details. The MK74CB217 Buffalo™ is designed to be used with ICS’s clock synthesizer devices. The inputs of the Buffalo are matched to the outputs of ICS clock synthesizers. Consult ICS for applications support. VDD Block Diagram 4 INA INB QA0 QB0 QA1 QB1 QA2 QB2 QA3 QB3 QA4 QB4 QA5 QB5 QA6 QB6 QA7 QB7 4 OEA (all A outputs) GND OEB (all B outputs) 1 Revision 12299 Printed 2/22/00 IntegratedCircuit Systems, Inc. • 525 Race Street • San Jose •CA •95126•(408) 295-9800tel • www.icst.com MDS74CB217A PRELIMINARY INFORMATION MK74CB217 Dual 1 to 8 Buffalo™ Clock Driver Pin Assignment INA QA0 QA1 QA2 VDD VDD QA3 QA4 GND GND QA5 QA6 QA7 OEA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Suggested Layout 28 INB 27 QB0 26 QB1 25 QB2 24 VDD 23 VDD 22 QB3 21 QB4 20 GND 19 GND 18 QB5 17 QB6 16 QB7 15 OEB V V 0.1µF 0.1µF G G For simplicity, terminating resistors are not shown for the outputs, but should be placed as close to the device as possible. It is most critical to have the 0.1µF decoupling capacitors closest. V = connect to VDD G = connect to GND Pin Descriptions Number 1 2, 3, 4 5, 6 7, 8 9, 10 11, 12, 13 14 15 16, 17, 18 19, 20 21, 22 23, 24 25, 26, 27 28 Name INA QA0, QA1, QA2 VDD QA3, QA4 GND QA5, QA6, QA7 OEA OEB QB7, QB6, QB5 GND QB4, QB3 VDD QB2, QB1, QB0 INB Type I O P O P O I I O P O P O I Description Clock input for eight A outputs. Clock A outputs. Power supply. Connect to 3.3 V or +5 V. Must be same as pins 23, 24. Clock A outputs. Connect to ground. Clock A outputs. Output Enable. Tri-states all A clock outputs when this input is low. Internal pull-up. Output Enable. Tri-states all B clock outputs when this input is low. Internal pull-up. Clock B outputs. Connect to ground. Clock B outputs. Power supply. Connect to +3.3 V or +5 V. Must be same as pins 5, 6. Clock B outputs. Clock input for eight B outputs. Type: I = Input, O = output, P = power supply connection 2 Revision 12299 Printed 2/22/00 IntegratedCircuit Systems, Inc. • 525 Race Street • San Jose •CA •95126•(408) 295-9800tel • www.icst.com MDS74CB217A PRELIMINARY INFORMATION MK74CB217 Dual 1 to 8 Buffalo™ Clock Driver Electrical Specifications Parameter Conditions Minimum Typical Maximum Units 7 VDD+0.5 VDD+0.5 70 260 150 V V V °C °C °C 5.5 V V V V V V V V mA Ω mA kΩ pF ABSOLUTE MAXIMUM RATINGS (Note 1) Supply Voltage, VDD Inputs Clock Outputs Ambient Operating Temperature Soldering Temperature Storage Temperature Referenced to GND Referenced to GND Referenced to GND 0.5 0.5 0 Max of 20 seconds -65 DC CHARACTERISTICS (VDD = 3.3 V unless noted) Operating Voltage, VDD Input High Voltage, VIH (INA, INB pins) Input Low Voltage, VIL (INA, INB pins) Input High Voltage, VIH (OEA, OEB pins) Input Low Voltage, VIL (OEA, OEB pins) Output High Voltage, 3.3V and 5V Output High Voltage, 3.3V and 5V Output Low Voltage, 3.3V and 5V Operating Supply Current, IDD, at 100 MHz 3.0 VDD-1.0 1.0 2.0 0.8 IOH=-12mA IOH=-25mA IOL=25mA No Load VDD-0.4 2.4 0.8 55 14 100 250 7 Output Impedance Short Circuit Current On-Chip Pull-up Resistor Input Capacitance 3.3 VDD/2 VDD/2 Each output OEA, OEB AC CHARACTERISTICS (VDD = 3.3 V unless noted) Input Clock Frequency Propagation Delay with load=15pF Output Clock Rise Time Output Clock Fall Time Output Clock Rising Edge Skew Output Clock A to B Skew Output Enable Time, OE high to output on Output Disable Time, OE low to tri-state Note 4 0 1.4 0.8 to 2.0V 2.0 to 0.8V At VDD/2. Note 2 At VDD/2. Note 3 100 100 200 3 2 2 250 250 20 20 MHz ns ns ns ps ps ns ns Notes: 1. Stresses beyond those listed under Absolute Maximum Ratings could cause permanent damage to the device. Prolonged exposure to levels above the operating limits but below the Absolute Maximums may affect device reliability. 2. Between any two A outputs, or any two B outputs, with equal loading. 3. Between any clock A output and any clock B output with INA connected to INB, and equal loading. 4. See discussion and graph of speed versus load. 3 Revision 12299 Printed 2/22/00 IntegratedCircuit Systems, Inc. • 525 Race Street • San Jose •CA •95126•(408) 295-9800tel • www.icst.com MDS74CB217A PRELIMINARY INFORMATION MK74CB217 Dual 1 to 8 Buffalo™ Clock Driver Maximum Speed The maximum speed at which the chip can operate is limited by power dissipation in the package. Graph 1 shows the operating frequency plotted against load capacitance per pin for a die temperature of 125°C. This is at VDD = 3.3 V, 70°C and with 33 Ω series termination resistors. The termination resistors are essential because they allow a large proportion of the total power to be dissipated outside the package. Reducing or eliminating the series termination will cause an increase in die temperature. It is not recommended to operate the chip at die temperatures greater than 125°C. Also note that the load capacitance per pin must include PC board parasitics such as trace capacitance. If not all outputs of the chip are used, it is possible to operate the chip faster with larger loads. Consult ICS for your specific requirement. 300 250 Do not operate in this area. 200 150 100 50 0 0 20 40 60 80 Load Capacitance/per pin (pF) Graph 1 MK74CB217 Maximum Speed 4 Revision 12299 Printed 2/22/00 IntegratedCircuit Systems, Inc. • 525 Race Street • San Jose •CA •95126•(408) 295-9800tel • www.icst.com MDS74CB217A PRELIMINARY INFORMATION MK74CB217 Dual 1 to 8 Buffalo™ Clock Driver Package Outline and Package Dimensions (For current dimensional specifications, see JEDEC publication no. 95.) 28 pin SSOP E1 Symbol A A1 b c D E1 E e L E D A1 e b Inches Min Max 0.053 0.069 0.004 0.01 0.008 0.012 0.007 0.010 0.386 0.394 0.150 0.157 0.228 0.244 .025 BSC 0.016 0.05 Millimeters Min Max 1.35 1.75 0.10 0.25 0.20 0.30 0.19 0.25 9.80 10.01 3.81 3.99 5.79 6.20 0.635 BSC 0.41 1.27 A c L Ordering Information Part/Order Number Marking Package Temperature MK74CB217R MK74CB217RTR MK74CB217R MK74CB217R 28 pin SSOP Add Tape & Reel 0-70 °C 0-70 °C While the information presented herein has been checked for both accuracy and reliability, ICS Incorporated assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by ICS. ICS reserves the right to change any circuitry or specifications without notice. ICS does not authorize or warrant any ICS product for use in life support devices or critical medical instruments. Buffalo is a trademark of ICS Incorporated 5 Revision 12299 Printed 2/22/00 IntegratedCircuit Systems, Inc. • 525 Race Street • San Jose •CA •95126•(408) 295-9800tel • www.icst.com MDS74CB217A