PIC16F716 Data Sheet 8-bit Flash-based Microcontroller with A/D Converter and Enhanced Capture/Compare/PWM 2003 Microchip Technology Inc. Preliminary DS41206A Note the following details of the code protection feature on Microchip devices: • Microchip products meet the specification contained in their particular Microchip Data Sheet. • Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. • There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. • Microchip is willing to work with the customer who is concerned about the integrity of their code. • Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as “unbreakable.” Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, MPLAB, PIC, PICmicro, PICSTART, PRO MATE and PowerSmart are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, microID, MXDEV, MXLAB, PICMASTER, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Accuron, Application Maestro, dsPICDEM, dsPICDEM.net, ECAN, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, PICC, PICkit, PICDEM, PICDEM.net, PowerCal, PowerInfo, PowerMate, PowerTool, rfLAB, rfPIC, Select Mode, SmartSensor, SmartShunt, SmartTel and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2003, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified. DS41206A-page ii Preliminary 2003 Microchip Technology Inc. PIC16F716 8-bit Flash-based Microcontroller with A/D Controller and Enhanced Capture/Compare PWM Microcontroller Core Features: Low-Power Features: • High-performance RISC CPU • Only 35 single-word instructions to learn - All single-cycle instructions except for program branches which are two-cycle • Operating speed: DC - 20 MHz clock input DC - 200 ns instruction cycle • Interrupt capability (up to 7 internal/external interrupt sources) • 8-level deep hardware stack • Direct, Indirect and Relative Addressing modes • Standby Current: - 100 nA @ 2.0V, typical • Operating Current: - 14 µA @ 32 kHz, 2.0V, typical - 120 µA @ 1 MHz, 2.0V, typical • Watchdog Timer Circuit: - 1 µA @ 2.0V, typical • Timer1 Oscillator Current: - 3.0 µA @ 32 kHz, 2.0V, typical Peripheral Features: Special Microcontroller Features • Timer0: 8-bit timer/counter with 8-bit prescaler • Timer1: 16-bit timer/counter with prescaler can be incremented during Sleep via external crystal/clock • Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler • Enhanced Capture, Compare, PWM module: - Capture is 16-bit, max. resolution is 12.5 ns - Compare is 16-bit, max. resolution is 200 ns - PWM maximum resolution is 10-bit - Enhanced PWM: - Single, Half-Bridge and Full-Bridge modes - Digitally programmable dead-band delay - Auto-shutdown/restart • 8-bit multi-channel Analog-to-Digital converter • 13 I/O pins with individual direction control • Programmable weak pull-ups on PORTB • Power-on Reset (POR) • Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) • Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation • Dual level Brown-out Reset circuitry - 2.5 VBOR (Typical) - 4.0 VBOR (Typical) • Programmable code protection • Power saving Sleep mode • Selectable oscillator options • Fully static design • In-Circuit Serial Programming (ICSP™) CMOS Technology • Wide operating voltage range: - Industrial: 2.0V to 5.5V - Extended: 3.0V to 5.5V • High Sink/Source Current 25/25 mA • Wide temperature range: - Industrial: -40°C to 85°C - Extended: -40°C to 125°C Memory Device PIC16F716 Flash Data 2048 x 14 128 x 8 2003 Microchip Technology Inc. I/O 8-bit A/D (ch) Timers 8/16 PWM (outputs) VDD Range 13 4 2/1 1/2/4 2.0V - 5.5V Preliminary DS41206A-page 1 PIC16F716 Pin Diagrams 18-pin PDIP, SOIC 1 2 3 4 5 6 7 8 9 PIC16F716 RA2/AN2 RA3/AN3/VREF RA4/T0CKI MCLR/VPP VSS RB0/INT/ECCPAS2 RB1/T1OSO/T1CKI RB2/T1OSI RB3/CCP1/P1A 18 17 16 15 14 13 12 11 10 RA1/AN1 RA0/AN0 OSC1/CLKIN OSC2/CLKOUT VDD RB7/P1D RB6/P1C RB5/P1B RB4/ECCPAS0 20 19 18 17 16 15 14 13 12 11 RA1/AN1 RA0/AN0 OSC1/CLKIN OSC2/CLKOUT VDD VDD RB7/P1D RB6/P1C RB5/P1B RB4/ECCPAS0 20-pin SSOP DS41206A-page 2 1 2 3 4 5 6 7 8 9 10 PIC16F716 RA2/AN2 RA3/AN3/VREF RA4/T0CKI MCLR/VPP VSS VSS RB0/INT/ECCPAS2 RB1/T1OSO/T1CKI RB2/T1OSI RB3/CCP1/P1A Preliminary 2003 Microchip Technology Inc. PIC16F716 Table of Contents 1.0 Device Overview .......................................................................................................................................................................... 5 2.0 Memory Organization ................................................................................................................................................................... 7 3.0 I/O Ports ..................................................................................................................................................................................... 19 4.0 Timer0 Module ........................................................................................................................................................................... 27 5.0 Timer1 Module ........................................................................................................................................................................... 29 6.0 Timer2 Module ........................................................................................................................................................................... 31 7.0 Enhanced Capture/Compare/PWM (ECCP) Module.................................................................................................................. 33 8.0 Analog-to-Digital Converter (A/D) Module.................................................................................................................................. 49 9.0 Special Features of the CPU...................................................................................................................................................... 55 10.0 Instruction Set Summary ............................................................................................................................................................ 71 11.0 Development Support................................................................................................................................................................. 85 12.0 Electrical Characteristics ............................................................................................................................................................ 91 13.0 DC and AC Characteristics Graphs and Tables....................................................................................................................... 107 14.0 Packaging Information.............................................................................................................................................................. 109 Appendix A: Revision History............................................................................................................................................................. 113 Appendix B: Conversion Considerations ........................................................................................................................................... 113 Appendix C: Migration from Base-line to MID-RANGE Devices ........................................................................................................ 114 On-Line Support................................................................................................................................................................................. 115 Systems Information and Upgrade Hot Line ...................................................................................................................................... 115 Reader Response .............................................................................................................................................................................. 116 Index .................................................................................................................................................................................................. 117 Product Identification System ............................................................................................................................................................ 123 TO OUR VALUED CUSTOMERS It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and enhanced as new volumes and updates are introduced. If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via E-mail at [email protected] or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We welcome your feedback. Most Current Data Sheet To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000). Errata An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: • Microchip’s Worldwide Web site; http://www.microchip.com • Your local Microchip sales office (see last page) • The Microchip Corporate Literature Center; U.S. FAX: (480) 792-7277 When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using. Customer Notification System Register on our web site at www.microchip.com/cn to receive the most current information on all of our products. 2003 Microchip Technology Inc. Preliminary DS41206A-page 3 PIC16F716 NOTES: DS41206A-page 4 Preliminary 2003 Microchip Technology Inc. PIC16F716 1.0 DEVICE OVERVIEW This document contains device specific information for the PIC16F716. Additional information may be found in the PICmicro® Mid-Range Reference Manual, (DS33023), which may be obtained from your local Microchip Sales Representative or downloaded from the Microchip web site (www.microchip.com). The Reference Manual should be considered a complementary document to this data sheet, and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules. Figure 1-1 is the block diagram for the PIC16F716 device. The pinouts are listed in Table 1-1. FIGURE 1-1: PIC16F716 BLOCK DIAGRAM 13 Flash 2K x 14 Program Memory Program Bus 8 Data Bus Program Counter RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI RAM 128 x 8 File Registers 8 Level Stack (13-bit) 14 RAM Addr(1) PORTB 9 Addr MUX Instruction reg Direct Addr 7 8 Indirect Addr FSR reg Status reg 8 3 OSC1/CLKIN Timing Generation OSC2/CLKOUT Oscillator Start-up Timer Timer0 ALU Power-on Reset 8 Watchdog Timer Brown-out Reset MCLR W reg VDD, VSS Timer1 Timer2 Enhanced CCP (ECCP) Note 1: RB0/INT/ECCPAS2 RB1/T1OSO/T1CKI RB2/T1OSI RB3/CCP1/P1A RB4/ECCPAS0 RB5/P1B RB6/P1C RB7/P1D MUX Power-up Timer Instruction Decode and Control PORTA A/D Higher order bits are from the Status register. 2003 Microchip Technology Inc. Preliminary DS41206A-page 5 PIC16F716 TABLE 1-1: PIC16F716 PINOUT DESCRIPTION Name Function Input Type Output Type Description Master clear (Reset) input. This pin is an active low Reset to the device. MCLR/VPP MCLR VPP P — Programming voltage input OSC1/CLKIN OSC1 XTAL — Oscillator crystal input CLKIN CMOS — External clock source input CLKIN ST — RC Oscillator mode OSC2 XTAL — Oscillator crystal output. Connects to crystal or resonator in Crystal Oscillator mode. CLKOUT — CMOS In RC mode, OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. OSC2/CLKOUT RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI RB0/INT/ECCPAS2 RB1/T1OSO/T1CKI RB2/T1OSI RB3/CCP1/P1A RB4/ECCPAS0 ST — RA0 TTL CMOS AN0 AN — RA1 TTL CMOS AN1 AN — Bidirectional I/O Analog Channel 0 input Bidirectional I/O Analog Channel 1 input RA2 TTL CMOS AN2 AN — RA3 TTL CMOS AN3 AN — Analog Channel 3 input VREF AN — A/D reference voltage input RA4 ST OD Bidirectional I/O. Open drain when configured as output. T0CKI ST — RB0 TTL CMOS Bidirectional I/O Analog Channel 2 input Bidirectional I/O Timer0 external clock input Bidirectional I/O. Programmable weak pull-up. INT ST — External Interrupt ECCPAS2 ST — ECCP Auto-Shutdown pin RB1 TTL CMOS Bidirectional I/O. Programmable weak pull-up. T1OSO — XTAL Timer1 oscillator output. Connects to crystal in Oscillator mode. T1CKI ST — RB2 TTL CMOS Timer1 external clock input T1OSI XTAL — RB3 TTL CMOS CCP1 ST CMOS Capture1 input, Compare1 output, PWM1 output. P1A — CMOS PWM P1A output RB4 TTL CMOS Bidirectional I/O. Programmable weak pull-up. Interrupt-onchange. Bidirectional I/O. Programmable weak pull-up. Timer1 oscillator input. Connects to crystal in Oscillator mode. Bidirectional I/O. Programmable weak pull-up. ECCPAS0 ST — RB5/P1B RB5 TTL CMOS Bidirectional I/O. Programmable weak pull-up. Interrupt-onchange. P1B — CMOS PWM P1B output RB6/P1C RB6 TTL CMOS Bidirectional I/O. Programmable weak pull-up. Interrupt-onchange. ST input when used as ICSP programming clock. P1C — CMOS PWM P1C output RB7 TTL CMOS Bidirectional I/O. Programmable weak pull-up. Interrupt-onchange. ST input when used as ICSP programming data. PWM P1D output RB7/P1D ECCP Auto-Shutdown pin P1D — CMOS VSS VSS P — Ground reference for logic and I/O pins. VDD VDD P — Positive supply for logic and I/O pins. Legend: I = Input O = Output P = Power DS41206A-page 6 AN = Analog input or output TTL = TTL compatible input XTAL = Crystal OD = Open drain ST = Schmitt Trigger input with CMOS levels CMOS = CMOS compatible input or output Preliminary 2003 Microchip Technology Inc. PIC16F716 2.0 MEMORY ORGANIZATION 2.2 There are two memory blocks in the PIC16F716 PICmicro® microcontroller device. Each block (program memory and data memory) has its own bus so that concurrent access can occur. The data memory is partitioned into multiple banks which contain the General Purpose Registers (GPR) and the Special Function Registers (SFR). Bits RP1 and RP0 of the Status register are the bank select bits. Additional information on device memory may be found in the PICmicro® Mid-Range Reference Manual, (DS33023). 2.1 Data Memory Organization RP1:RP0(1) (status<6:5>) Bank 00 0 01 1 10 2(2) 11 3(2) Program Memory Organization The PIC16F716 has a 13-bit program counter capable of addressing an 8K x 14 program memory space. The PIC16F716 has 2K x 14 words of program memory. Accessing a location above the physically implemented address will cause a wrap-around. The Reset vector is at 0000h and the interrupt vector is at 0004h. FIGURE 2-1: PROGRAM MEMORY MAP AND STACK OF PIC16F716 PC<12:0> CALL, RETURN RETFIE, RETLW Note 1: 2: Maintain Status bit 6 clear to ensure upward compatibility with future products. Not implemented Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are General Purpose Registers, implemented as static RAM. All implemented banks contain Special Function Registers. The upper 16 bytes of GPR space and some “high use” Special Function Registers in Bank 0 are mirrored in Bank 1 for code reduction and quicker access. 13 Stack Level 1 User Memory Space Stack Level 8 Reset Vector 0000h Interrupt Vector 0004h 0005h On-chip Program Memory 07FFh 0800h 1FFFh 2003 Microchip Technology Inc. Preliminary DS41206A-page 7 PIC16F716 2.2.1 GENERAL PURPOSE REGISTER FILE FIGURE 2-2: The register file can be accessed either directly or indirectly through the File Select Register FSR (Section 2.5 “Indirect Addressing, INDF and FSR Registers”). REGISTER FILE MAP File Address File Address 00h INDF(1) INDF(1) 01h TMR0 02h PCL PCL 82h 03h STATUS STATUS 83h 04h FSR FSR 84h 05h PORTA TRISA 85h 06h PORTB TRISB 86h 80h OPTION_REG 81h 07h 87h 08h 88h 89h 09h 0Ah PCLATH PCLATH 8Ah 0Bh INTCON INTCON 8Bh 0Ch PIR1 PIE1 8Ch 0Eh TMR1L PCON 0Fh TMR1H 8Fh 10h T1CON 90h 11h TMR2 12h T2CON 8Dh 0Dh 8Eh 91h PR2 92h 93h 13h 14h 94h 15h CCPR1L 95h 16h CCPR1H 96h 17h CCP1CON 97h 18h PWM1CON 98h 19h ECCPAS 99h 1Ah 9Ah 1Bh 9Bh 1Ch 9Ch 1Dh 9Dh 9Eh 1Eh ADRES 1Fh ADCON0 ADCON1 9Fh 20h General Purpose Registers General Purpose Registers 32 Bytes A0h 80 Bytes C0h 6Fh 70h 7Fh BFh EFh 16 Bytes Accesses 70-7Fh Bank 0 Bank 1 F0h FFh Unimplemented data memory locations, read as '0'. Note 1: DS41206A-page 8 Preliminary Not a physical register. 2003 Microchip Technology Inc. PIC16F716 2.2.2 SPECIAL FUNCTION REGISTERS The Special Function Registers are registers used by the CPU and peripheral modules for controlling the desired operation of the device. These registers are implemented as static RAM. A list of these registers is give in Table 2-1. The Special Function Registers can be classified into two sets; core (CPU) and peripheral. Those registers associated with the core functions are described in detail in this section. Those related to the operation of the peripheral features are described in detail in that peripheral feature section. TABLE 2-1: Address SPECIAL FUNCTION REGISTER SUMMARY BANK 0 Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Page 18 00h INDF(1) Addressing this location uses contents of FSR to address data memory (not a physical register) 0000 0000 01h TMR0 Timer0 module’s register xxxx xxxx 27 02h PCL(1) Program Counter's (PC) Least Significant Byte 0000 0000 17 03h STATUS(1) 04h FSR (1) 05h PORTA(5,6) 06h (5,6) PORTB 07h-09h IRP(4) RP1(4) RP0 TO PD Z DC C Indirect data memory address pointer — 0Ah PCLATH(1,2) 0Bh INTCON(1) 0Ch PIR1 — — —(7) PORTA Data Latch when written: PORTA pins when read PORTB Data Latch when written: PORTB pins when read Unimplemented 0001 1xxx 11 xxxx xxxx 18 --xx 0000 19 xxxx xxxx 21 — — — — Write Buffer for the upper 5 bits of the Program Counter ---0 0000 17 GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 13 — ADIF — — — CCP1IF TMR2IF TMR1IF -0-- 0000 15 0Dh — 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register xxxx xxxx 29 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register xxxx xxxx 29 10h T1CON --00 0000 29 11h TMR2 0000 0000 31 12h T2CON -000 0000 31 13h-14h — Unimplemented — — — T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON Timer2 module’s register — TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 Unimplemented — 15h CCPR1L Capture/Compare/PWM Register 1 (LSB) xxxx xxxx 34 16h CCPR1H Capture/Compare/PWM Register 1 (MSB) xxxx xxxx 34 17h CCP1CON P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 0000 0000 33 18h PWM1CON PRSEN PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 0000 0000 46 19h ECCPAS —(8) ECCPAS0 PSSAC1 PSSAC0 PSSBD1 PSSBD0 00-0 0000 46 1Ah-1Dh 1Eh 1Fh ADCON0 Legend: Note — ADRES 1: 2: 3: 4: 5: 6: 7: 8: ECCPASE ECCPAS2 Unimplemented — A/D Result Register ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE —(7) ADON xxxx xxxx 49 0000 0000 49 x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as ‘0’, Shaded locations are unimplemented, read as ‘0’. These registers can be addressed from either bank. The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8> whose contents are transferred to the upper byte of the program counter. Other (non Power-up) Resets include: external Reset through MCLR and the Watchdog Timer Reset. The IRP and RP1 bits are reserved. Always maintain these bits clear. On any device Reset, these pins are configured as inputs. This is the value that will be in the port output latch. Reserved bits, do not use. ECCPAS1 bit is not used on PIC16F716. 2003 Microchip Technology Inc. Preliminary DS41206A-page 9 PIC16F716 TABLE 2-2: Address SPECIAL FUNCTION REGISTER SUMMARY BANK 1 Name 80h INDF(1) 81h OPTION_REG 82h PCL(1) 83h STATUS(1) 84h FSR(1) 85h TRISA 86h TRISB 87h-89h — 8Ah PCLATH(1,2) 8Bh INTCON(1) 8Ch PIE1 8Dh — 8Eh PCON 8Fh-91h 92h 9Fh Note 1: 2: 3: 4: 5: 6: 7: Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Addressing this location uses contents of FSR to address data memory (not a physical register) RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 Program Counter's (PC) Least Significant Byte IRP(4) RP1(4) RP0 TO PD Z DC C Indirect data memory address pointer — — —(7) PORTA Data Direction Register PORTB Data Direction Register Unimplemented — — GIE PEIE T0IE INTE RBIE T0IF INTF — ADIE — — — CCP1IE TMR2IE Write Buffer for the upper 5 bits of the Program Counter — — Unimplemented — 0000 0000 18 1111 1111 12 0000 0000 17 0001 1xxx 11 xxxx xxxx 18 --11 1111 19 1111 1111 21 17 RBIF 0000 000x 13 TMR1IE -0-- -000 14 — — — — — POR BOR ---- --qq 16 — Timer2 Period Register — Page ---0 0000 Unimplemented — Value on: POR, BOR — — Unimplemented ADCON1 Legend: Bit 6 — PR2 93h-9Eh Bit 7 1111 1111 32, 36 — — — — PCFG2 PCFG1 PCFG0 ---- -000 50 x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0', Shaded locations are unimplemented, read as ‘0’. These registers can be addressed from either bank. The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8> whose contents are transferred to the upper byte of the program counter. Other (non Power-up) Resets include: external Reset through MCLR and the Watchdog Timer Reset. The IRP and RP1 bits are reserved. Always maintain these bits clear. On any device Reset, these pins are configured as inputs. This is the value that will be in the port output latch. Reserved bits, do not use. DS41206A-page 10 Preliminary 2003 Microchip Technology Inc. PIC16F716 2.2.2.1 Status Register The Status register, shown in Register 2-1, contains the arithmetic status of the ALU, the Reset status and the bank select bits for data memory. The Status register can be the destination for any instruction, as with any other register. If the Status register is the destination for an instruction that affects the Z, DC or C bits, then the write to these three bits is disabled. These bits are set or cleared according to the device logic. Furthermore, the TO and PD bits are not writable. Therefore, the result of an instruction with the Status register as destination may be different than intended. It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the Status register because these instructions do not affect the Z, C or DC bits from the Status register. For other instructions, not affecting any Status bits, see the “Instruction Set Summary.” Note 1: The PIC16F716 does not use bits IRP and RP1 (STATUS<7:6>). Maintain these bits clear to ensure upward compatibility with future products. 2: The C and DC bits operate as a borrow and digit borrow bit, respectively, in subtraction. See the SUBLW and SUBWF instructions for examples. For example, CLRF STATUS will clear the upper-three bits and set the Z bit. This leaves the Status register as 000u u1uu (where u = unchanged). REGISTER 2-1: STATUS REGISTER (ADDRESS: 03h, 83h) R/W-0 R/W-0 R/W-0 R-1 R-1 R/W-x R/W-x R/W-x IRP(1) RP1(1) RP0 TO PD Z DC C bit 7 bit 0 bit 7 IRP: Register Bank Select bit (used for indirect addressing)(1) 1 = Bank 2, 3 (100h – 1FFh) 0 = Bank 0, 1 (00h – FFh) bit 6-5 RP1(1):RP0: Register Bank Select bits (used for direct addressing) 01 = Bank 1 (80h – FFh) 00 = Bank 0 (00h – 7Fh) Each bank is 128 bytes bit 4 TO: Time-out bit 1 = After power-up, CLRWDT instruction or SLEEP instruction 0 = A WDT time-out occurred bit 3 PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction bit 2 Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero bit 1 DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result bit 0 C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions)(2) 1 = A carry-out from the Most Significant bit of the result occurred 0 = No carry-out from the Most Significant bit of the result occurred Note 1: 2: Reserved, maintain clear For borrow the polarity is reversed. A subtraction is executed by adding the two’s complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 11 PIC16F716 2.2.2.2 OPTION_REG Register Note: The OPTION_REG register is a readable and writable register, which contains various control bits to configure the TMR0 prescaler/WDT postscaler (single assignable register known also as the prescaler), the External INT Interrupt, TMR0 and the weak pull-ups on PORTB. REGISTER 2-2: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. OPTION_REG REGISTER (ADDRESS: 81h) R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 bit 7 bit 0 bit 7 RBPU: PORTB Weak Pull-up Enable bit 1 = PORTB weak pull-ups are disabled 0 = PORTB weak pull-ups are determined by alternate function or TRISBn bit value bit 6 INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin bit 5 T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) bit 4 T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin bit 3 PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module bit 2-0 PS2:PS0: Prescaler Rate Select bits Bit Value TMR0 Rate WDT Rate 000 1:2 1:1 001 1:4 1:2 010 1:8 1:4 011 1 : 16 1:8 100 1 : 32 1 : 16 101 1 : 64 1 : 32 110 1 : 128 1 : 64 111 1 : 256 1 : 128 Legend: DS41206A-page 12 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared Preliminary x = Bit is unknown 2003 Microchip Technology Inc. PIC16F716 2.2.2.3 INTCON Register Note: The INTCON Register is a readable and writable register which contains various enable and flag bits for the TMR0 register overflow, RB Port change and external RB0/INT pin interrupts. REGISTER 2-3: Interrupt flag bits get set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. INTCON REGISTER (ADDRESS: 0Bh, 8Bh) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-x GIE PEIE T0IE INTE RBIE T0IF INTF RBIF bit 7 bit 0 bit 7 GIE: Global Interrupt Enable bit 1 = Enables all un-masked interrupts 0 = Disables all interrupts bit 6 PEIE: Peripheral Interrupt Enable bit 1 = Enables all un-masked peripheral interrupts 0 = Disables all peripheral interrupts bit 5 T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt bit 4 INTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt bit 3 RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt bit 2 T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (must be cleared in software) 0 = TMR0 register did not overflow bit 1 INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (must be cleared in software) 0 = The RB0/INT external interrupt did not occur bit 0 RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 pins changed state (must be cleared in software) 0 = None of the RB7:RB4 pins have changed state Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 13 PIC16F716 2.2.2.4 PIE1 Register Note: Bit PEIE (INTCON<6>) must be set to enable any peripheral interrupt. This register contains the individual enable bits for the peripheral interrupts. REGISTER 2-4: PIE1 REGISTER (ADDRESS: 8Ch) U-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 — ADIE — — — CCP1IE TMR2IE TMR1IE bit 7 bit 0 bit 7 Unimplemented: Read as ‘0’ bit 6 ADIE: A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt bit 5-3 Unimplemented: Read as ‘0’ bit 2 CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt bit 0 TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt Legend: DS41206A-page 14 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared Preliminary x = Bit is unknown 2003 Microchip Technology Inc. PIC16F716 2.2.2.5 PIR1 Register Note: This register contains the individual flag bits for the peripheral interrupts. REGISTER 2-5: Interrupt flag bits get set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. PIR1 REGISTER (ADDRESS: 0Ch) U-0 R/W-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 — ADIF — — — CCP1IF TMR2IF TMR1IF bit 7 bit 0 bit 7 Unimplemented: Read as ‘0’ bit 6 ADIF: A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete bit 5-3 Unimplemented: Read as ‘0’ bit 2 CCP1IF: CCP1 Interrupt Flag bit Capture Mode 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM Mode Unused in this mode bit 1 TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred bit 0 TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 15 PIC16F716 2.2.2.6 PCON Register Note: The Power Control (PCON) register contains a flag bit to allow differentiation between a Power-on Reset (POR) to an external MCLR Reset or WDT Reset. These devices contain an additional bit to differentiate a Brown-out Reset condition from a Power-on Reset condition. If the BOREN configuration bit is set, BOR is ‘1’ on Power-on Reset and reset to ‘0’ when a Brown-out condition occurs. BOR must then be set by the user and checked on subsequent resets to see if it is clear, indicating that another Brown-out has occurred. If the BOREN configuration bit is clear, BOR is unknown on Power-on Reset. REGISTER 2-6: PCON REGISTER (ADDRESS: 8Eh) U-0 U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-q — — — — — — POR BOR bit 7 bit 0 bit 7-2 Unimplemented: Read as ‘0’ bit 1 POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) bit 0 BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs) DS41206A-page 16 Legend: q = Depends on condition R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared Preliminary x = Bit is unknown 2003 Microchip Technology Inc. PIC16F716 2.3 FIGURE 2-3: PCL and PCLATH The Program Counter (PC) specifies the address of the instruction to fetch for execution. The PC is 13 bits wide. The low byte is called the PCL register. This register is readable and writable. The high byte is called the PCH register. This register contains the PC<12:8> bits and is not directly readable or writable. All updates to the PCH register go through the PCLATH register. 2.3.1 Care should be exercised when modifying the PCL register to jump into a look-up table or program branch table (computed GOTO). With PCLATH set to the table start address, if the table is greater than 255 instructions or if the lower 8 bits of the memory address rolls over from 0xFF to 0x00 in the middle of the table, then PCLATH must be incremented for each address rollover that occurs between the table beginning and the target address. PROGRAM MEMORY PAGING The CALL and GOTO instructions provide 11 bits of address to allow branching within any 2K program memory page. When doing a CALL or GOTO instruction, the upper bit of the address is provided by PCLATH<3>. When doing a CALL or GOTO instruction, the user must ensure that the page select bit is programmed so that the desired program memory page is addressed. If a RETURN from a CALL instruction (or interrupt) is executed, the entire 13-bit PC is pushed onto the stack. Therefore, manipulation of the PCLATH<3> bit is not required for the RETURN instructions (which POPs the address from the stack). 2003 Microchip Technology Inc. PCL 8 7 8 PCLATH<4:0> 5 0 Instruction with PCL as Destination ALU PCLATH PCL PCH 1110 0 8 7 GOTO, CALL Executing any instruction with the PCL register as the destination simultaneously causes the Program Counter PC<12:8> bits (PCH) to be replaced by the contents of PCLATH register. This allows the entire contents of the program counter to be changed by first writing the desired upper 5 bits to the PCLATH register. When the lower 8 bits are then written to the PCL register, all 13 bits of the program counter will change to the values contained in the PCLATH register and those being written to the PCL register. 2.3.2 PCH 12 12 MODIFYING PCL LOADING OF PC IN DIFFERENT SITUATIONS PCLATH<4:3> 2 11 Opcode <10:0> PCLATH 2.4 Stack The stack allows a combination of up to 8 program calls and interrupts to occur. The stack contains the return address from this branch in program execution. Mid-range devices have an 8-level deep x 13-bit wide hardware stack. The stack space is not part of either program or data space, and the stack pointer is not readable or writable. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not modified when the stack is PUSHed or POPed. After the stack has been PUSHed 8 times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on). Preliminary DS41206A-page 17 PIC16F716 2.5 EXAMPLE 2-2: Indirect Addressing, INDF and FSR Registers The INDF register is not a physical register. Addressing INDF actually addresses the register whose address is contained in the FSR register (FSR is a pointer). This is indirect addressing. EXAMPLE 2-1: MOVLW MOVWF CLRF INCF BTFSS GOTO NEXT INDIRECT ADDRESSING HOW TO CLEAR RAM USING INDIRECT ADDRESSING 0x20 FSR INDF FSR FSR,4 NEXT ;initialize pointer ;to RAM ;clear RAM & FSR ;inc pointer ;all done? ;no, clear next CONTINUE • • • • Register file 05 contains the value 10h Register file 06 contains the value 0Ah Load the value 05 into the FSR register A read of the INDF register will return the value of 10h • Increment the value of the FSR register by one (FSR = 06) • A read of the INDR register now will return the value of 0Ah. : ;yes, continue An effective 9-bit address is obtained by concatenating the 8-bit FSR register and the IRP bit (STATUS<7>), as shown in Figure 2-4. However, IRP is not used in the PIC16F716. Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no-operation (although Status bits may be affected). A simple program to clear RAM locations 20h – 2Fh using indirect addressing is shown in Example 2-2. FIGURE 2-4: DIRECT/INDIRECT ADDRESSING Direct Addressing RP1: RP0 6 Indirect Addressing from opcode 0 IRP (2) bank select bank select location select 00 00h 01 80h 10 100h FSR register 0 7Fh Bank 0 FFh 17Fh Bank 1 location select 11 180h (3) Data Memory(1) Note 1: 2: 3: 7 (2) (3) 1FFh Bank 2 Bank 3 For register file map detail see Figure 2-2. Maintain clear for upward compatibility with future products. Not implemented. DS41206A-page 18 Preliminary 2003 Microchip Technology Inc. PIC16F716 3.0 I/O PORTS EXAMPLE 3-1: Some pins for these I/O ports are multiplexed with an alternate function for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Additional information on I/O ports may be found in the PICmicro® Mid-Range Reference Manual, (DS33023). 3.1 PORTA and the TRISA Register PORTA is a 5-bit wide bidirectional port. The corresponding data direction register is TRISA. Setting a TRISA bit (= 1) will make the corresponding PORTA pin an input (i.e., put the corresponding output driver in a High-impedance mode). Clearing a TRISA bit (= 0) will make the corresponding PORTA pin an output (i.e., put the contents of the output latch on the selected pin). Reading the PORTA register reads the status of the pins, whereas writing to it will write to the port latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, the value is modified and then written to the port data latch. Pin RA4 is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. The RA4/T0CKI pin is a Schmitt Trigger input and an open drain output. All other RA port pins have TTL input levels and full CMOS output drivers. BCF CLRF STATUS, RP0 PORTA BSF MOVLW STATUS, RP0 0xEF MOVWF TRISA BCF STATUS, RP0 FIGURE 3-1: DATA BUS D BLOCK DIAGRAM OF RA3:RA0 Q VDD CK Q P Data Latch D WR TRIS CK I/O pin N Q VSS Q VSS Analog Input mode TRIS Latch RD TRIS On a Power-on Reset, these pins are configured as analog inputs and read as ‘0’. The TRISA register controls the direction of the RA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs. ; ;Initialize PORTA by ;clearing output ;data latches ;Select Bank 1 ;Value used to ;initialize data ;direction ;Set RA<3:0> as inputs ;RA<4> as outputs ;Return to Bank 0 VDD WR PORT PORTA pins, RA3:0, are multiplexed with analog inputs and analog VREF input. The operation of each pin is selected by clearing/setting the control bits in the ADCON1 register (A/D Control Register 1). Note: INITIALIZING PORTA Q TTL Input Buffer D EN RD PORT To A/D Converter Note: Setting RA3:0 to output while in Analog mode will force pins to output contents of data latch. 2003 Microchip Technology Inc. Preliminary DS41206A-page 19 PIC16F716 FIGURE 3-2: BLOCK DIAGRAM OF RA4/T0CKI PIN Data Latch DATA BUS Q D WR PORT CK RA4/T0CKI Q N TRIS Latch WR TRIS VSS Q D CK VSS Schmitt Trigger Input Buffer Q RD TRIS Q D ENEN RD PORT TMR0 Clock Input TABLE 3-1: PORTA FUNCTIONS Name RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI Bit# Buffer bit 0 bit 1 bit 2 bit 3 bit 4 TTL TTL TTL TTL ST Function Input/output or analog input Input/output or analog input Input/output or analog input Input/output or analog input or VREF Input/output or external clock input for Timer0 Output is open drain type Legend: TTL = TTL input, ST = Schmitt Trigger input TABLE 3-2: Address 05h SUMMARY OF REGISTERS ASSOCIATED WITH PORTA Name PORTA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other Resets — —(1) RA4 RA2 RA1 RA0 --xx 0000 --uu uuuu PORTA Data Direction Register — 85h TRISA — — —(1) 9Fh ADCON1 — — — — RA3 — PCFG2 PCFG1 PCFG0 --11 1111 --11 1111 ---- -000 ---- -000 Legend: x = unknown, u = unchanged, - = unimplemented locations read as ‘0’. Shaded cells are not used by PORTA. Note 1: Reserved bits, do not use. DS41206A-page 20 Preliminary 2003 Microchip Technology Inc. PIC16F716 3.2 PORTB and the TRISB Register PORTB is an 8-bit wide bidirectional port. The corresponding data direction register is TRISB. Setting a TRISB bit (= 1) will make the corresponding PORTB pin an input (i.e., put the corresponding output driver in a High-impedance mode). Clearing a TRISB bit (= 0) will make the corresponding PORTB pin an output (i.e., put the contents of the output latch on the selected pin). EXAMPLE 3-2: INITIALIZING PORTB BCF CLRF STATUS, RP0 PORTB BSF MOVLW STATUS, RP0 0xCF MOVWF TRISB ;select Bank 0 ;Initialize PORTB by ;clearing output ;data latches ;Select Bank 1 ;Value used to ;initialize data ;direction ;Set RB<3:0> as inputs ;RB<5:4> as outputs ;RB<7:6> as inputs Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION_REG<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. FIGURE 3-3: BLOCK DIAGRAM OF RB0/INT/ECCPAS2 PIN RBPU(1) weak P pull-up Data Latch D Q DATA BUS WR PORT Four of PORTB’s pins, RB7:RB4, have an interrupt-onchange feature. Only pins configured as inputs can cause this interrupt to occur (i.e., any RB7:RB4 pin configured as an output is excluded from the interrupton-change comparison). The input pins, RB7:RB4, are compared with the old value latched on the last read of PORTB. The “mismatch” outputs of RB7:RB4 are OR’ed together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>). This interrupt can wake the device from Sleep. The user, in the interrupt service routine, can clear the interrupt in the following manner: 1. 2. Perform a read of PORTB to end the mismatch condition. Clear flag bit RBIF. A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition and allow flag bit RBIF to be cleared. RB0/ INT/ ECCPAS2 CK TRIS Latch D Q WR TRIS When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTB pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. Since the TRIS bit override is in effect while the peripheral is enabled, read-modifywrite instructions (such as BSF, BCF, XORWF) with TRISB as the destination should be avoided. The user should refer to the corresponding peripheral section for the correct TRIS bit settings. The interrupt-on-change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt-on-change feature. Polling of PORTB is not recommended while using the interrupt-on-change feature. VDD VDD PORTB pins RB7:RB0 are multiplexed with several peripheral functions (Table 3-3). VSS CK TTL Input Buffer RD TRIS Q RD PORT RB0/INT D EN Schmitt Trigger Buffer RD PORT ECCPAS2: ECCP Auto-shutdown input Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). 2003 Microchip Technology Inc. Preliminary DS41206A-page 21 PIC16F716 FIGURE 3-4: BLOCK DIAGRAM OF RB1/T1OSO/T1CKI PIN VDD T1OSCEN RBPU(1) weak P pull-up VDD DATA BUS Data Latch D WR PORTB CK RB1/T1OSO/T1CKI Q Q TRIS Latch D WR TRISB CK VSS Q Q RD TRISB T1OSCEN TTL Buffer Q D EN RD PORTB T1OSI (From RB2) TMR1 oscillator To Timer1 clock input ST Buffer Note FIGURE 3-5: 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). BLOCK DIAGRAM OF RB2/T1OSI PIN VDD T1OSCEN RBPU(1) weak P pull-up VDD Data Latch DATA BUS D WR PORTB CK Q RB2/T1OSI Q TRIS Latch D WR TRISB CK Q VSS Q RD TRIS T1OSCEN TTL Buffer Q D EN RD PORTB TMR1 Oscillator T1OSO (To RB1) Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). DS41206A-page 22 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 3-6: BLOCK DIAGRAM OF RB3/CCP1/P1A PIN VDD RBPU(1) [PWMA(P1A) / CCP1 Compare] Output Enable [PWMA(P1A) / CCP1 Compare] Output weak P pull-up VDD 1 RB3/CCP1/P1A 0 PWMA(P1A) Auto-shutdown tri-state VSS Data Latch DATA BUS D WR PORTB CK Q Q TRIS Latch D WR TRISB CK Q Q RD TRIS TTL Buffer Q D EN RD PORTB Schmitt Trigger Buffer CCP - Capture input Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). FIGURE 3-7: BLOCK DIAGRAM OF RB4/ECCPAS0 PIN VDD RBPU(1) DATA BUS WR PORTB weak P pull-up Data Latch D Q RB4/ECCPAS0 CK TRIS Latch D Q WR TRISB VDD VSS TTL Buffer CK ST Buffer RD TRIS Q Latch D EN RD PORT Q1 Set RBIF From other RB7:RB4 pins Q D RD PORT EN ECCPAS0: ECCP Auto-Shutdown input 2003 Microchip Technology Inc. Preliminary Q3 Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). DS41206A-page 23 PIC16F716 FIGURE 3-8: BLOCK DIAGRAM OF RB5/P1B PIN VDD RBPU(1) PWMB(P1B) Enable PWMB(P1B) Data out PWMB(P1B) Auto-shutdown tri-state Data Latch DATA BUS D Q WR PORTB weak P pull-up VDD 1 RB5/P1B 0 CK TRIS Latch D Q WR TRISB CK VSS TTL Buffer Q RD TRISB Q Latch D EN RD PORTB Q1 Set RBIF Q From other RB7:RB4 pins D RD PORTB Q3 EN Note FIGURE 3-9: 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). BLOCK DIAGRAM OF RB6/P1C PIN VDD RBPU(1) PWMC(P1C) Enable PWMC(P1C) Data out PWMC(P1C) Auto-shutdown tri-state Data Latch DATA BUS D Q WR PORTB weak P pull-up VDD 1 RB6/P1C 0 CK TRIS Latch D Q WR TRISB CK VSS Q ST Buffer RD TRISB Q TTL Buffer Latch D EN RD PORTB Q1 Set RBIF From other RB7:RB4 pins Q D EN RD PORTB Q3 ICSPC - In circuit serial programming clock input Note 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). DS41206A-page 24 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 3-10: BLOCK DIAGRAM OF RB7/P1D PIN VDD RBPU(1) PWMD(P1D) Enable PWMD(P1D) Data out PWMD(P1D) Auto-shutdown tri-state Data Latch DATA BUS D Q WR PORTB weak P pull-up VDD 1 RB7/P1D 0 CK TRIS Latch D Q WR TRISB CK VSS Q ST Buffer RD TRISB Q Latch D EN RD PORTB TTL Buffer Q1 Set RBIF Q From other RB7:RB4 pins D EN Note RD PORTB Q3 ICSPD - In circuit serial programming data input TABLE 3-3: Name 1: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>). PORTB FUNCTIONS Bit# Buffer bit 0 TTL/ST(1) Function Input/output pin or external interrupt input. Internal software programmable weak pull-up. ECCP auto-shutdown input. Input/output pin or Timer1 oscillator output, or Timer1 clock input. Internal bit 1 TTL/ST(1) software programmable weak pull-up. See Section 5.0 “Timer1 Module” for detailed operation. RB2/T1OSI bit 2 TTL/XTAL Input/output pin or Timer1 oscillator input. Internal software programmable weak pull-up. See Section 5.0 “Timer1 Module” for detailed operation. RB3/CCP1/ bit 3 TTL/ST(1) Input/output pin or Capture1 input, or Compare1 output, or PWM A output. P1A Internal software programmable weak pull-up. See CCP1 section for detailed operation. bit 4 TTL Input/output pin (with interrupt-on-change). Internal software programmable RB4/ weak pull-up. ECCP auto-shutdown input. ECCPAS0 RB5/P1B bit 5 TTL Input/output pin (with interrupt-on-change). Internal software programmable weak pull-up. PWM B output. Input/output pin (with interrupt-on-change). Internal software programmable RB6/P1C bit 6 TTL/ST(2) weak pull-up. PWM C output. Serial programming clock. (2) Input/output pin (with interrupt-on-change). Internal software programmable RB7/P1D bit 7 TTL/ST weak pull-up. PWM D output. Serial programming data. Legend: TTL = TTL input, ST = Schmitt Trigger input, XTAL = Crystal Oscillator input Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt or peripheral input. 2: This buffer is a Schmitt Trigger input when used in Serial Programming mode. RB0/INT/ ECCPAS2 RB1/T1OS0/ T1CKI 2003 Microchip Technology Inc. Preliminary DS41206A-page 25 PIC16F716 TABLE 3-4: Address 06h SUMMARY OF REGISTERS ASSOCIATED WITH PORTB Name PORTB 86h TRISB 81h OPTION_REG Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other Resets RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 xxxx xxxx uuuu uuuu 1111 1111 1111 1111 T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 PORTB Data Direction Register RBPU INTEDG T0CS Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB. DS41206A-page 26 Preliminary 2003 Microchip Technology Inc. PIC16F716 4.0 TIMER0 MODULE 4.2 An 8-bit counter is available as a prescaler for the Timer0 module or as a postscaler for the Watchdog Timer, respectively (Figure 4-2). For simplicity, this counter is being referred to as “prescaler” throughout this data sheet. The Timer0 module timer/counter has the following features: • • • • • • Prescaler 8-bit timer/counter Readable and writable Internal or external clock select Edge select for external clock 8-bit software programmable prescaler Interrupt on overflow from FFh to 00h Note: Figure 4-1 is a simplified block diagram of the Timer0 module. Additional information on timer modules is available in the PICmicro® Mid-Range Reference Manual, (DS33023). 4.1 There is only one prescaler available, which is mutually exclusively shared between the Timer0 module and Watchdog Timer. Thus, a prescaler assignment for the Timer0 module means that there is no prescaler for the Watchdog Timer and vice-versa. The prescaler is not readable or writable. The PSA and PS2:PS0 bits (OPTION_REG<3:0>) determine the prescaler assignment and prescale ratio. Timer0 Operation Clearing bit PSA will assign the prescaler to the Timer0 module. When the prescaler is assigned to the Timer0 module, prescale values of 1:2, 1:4, ..., 1:256 are selectable. Timer0 can operate as a timer or as a counter. Timer mode is selected by clearing bit T0CS (OPTION_REG<5>). In Timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. Setting bit PSA will assign the prescaler to the Watchdog Timer (WDT). When the prescaler is assigned to the WDT, prescale values of 1:1, 1:2, ..., 1:128 are selectable. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g. CLRF 1, MOVWF 1, BSF 1,x....etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the WDT. Counter mode is selected by setting bit T0CS (OPTION_REG<5>). In Counter mode, Timer0 will increment on every rising or falling edge of pin RA4/ T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit T0SE (OPTION_REG<4>). Clearing bit T0SE selects the rising edge. Restrictions on the external clock input are discussed below. When an external clock input is used for Timer0, it must meet certain requirements. The requirements ensure the external clock can be synchronized with the internal phase clock (TOSC). Also, there is a delay in the actual incrementing of Timer0 after synchronization. Note: Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count, but will not change the prescaler assignment. Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. Additional information on external clock requirements is available in the PICmicro® Mid-Range Reference Manual, (DS33023). FIGURE 4-1: TIMER0 BLOCK DIAGRAM Data Bus FOSC/4 0 PSOUT 8 1 1 RA4/T0CKI pin Programmable Prescaler(2) 0 Sync with Internal clock TMR0 PSOUT (2 cycle delay) T0SE(1) 3 T0CS(1) Note 1: 2: PS2, PS1, PS0(1) PSA(1) Set interrupt flag bit T0IF on overflow T0CS, T0SE, PSA, PS2:PS0 (OPTION_REG<5:0>). The prescaler is shared with Watchdog Timer (refer to Figure 4-2 for detailed block diagram). 2003 Microchip Technology Inc. Preliminary DS41206A-page 27 PIC16F716 4.2.1 SWITCHING PRESCALER ASSIGNMENT 4.3 The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module interrupt service routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from Sleep since the timer is shut off during Sleep. The prescaler assignment is fully under software control (i.e., it can be changed “on-the-fly” during program execution). Note: To avoid an unintended device Reset, a specific instruction sequence (shown in the PICmicro® Mid-Range Reference Manual, DS33023) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled. FIGURE 4-2: Timer0 Interrupt BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER Data Bus CLKOUT (=FOSC/4) 0 RA4/T0CKI pin 8 M U X 1 M U X 0 1 SYNC 2 Cycles TMR0 reg T0SE T0CS 0 1 Watchdog Timer Set flag bit T0IF on Overflow PSA 8-bit Prescaler M U X 8 8 - to - 1MUX PS2:PS0 PSA 1 0 WDT Enable bit MUX PSA WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>). TABLE 4-1: Address REGISTERS ASSOCIATED WITH TIMER0 Name 01h TMR0 0Bh,8Bh INTCON 81h OPTION_REG 85h TRISA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 T0IE INTE RBIE T0IF INTF RBIF T0CS T0SE PSA PS2 PS1 PS0 —(1) Bit 4 Timer0 module’s register GIE PEIE RBPU INTEDG — — PORTA Data Direction Register Value on: POR, BOR Value on all other Resets xxxx xxxx uuuu uuuu 0000 000x 0000 000u 1111 1111 1111 1111 --11 1111 --11 1111 Legend: x = unknown, u = unchanged, - = unimplemented locations read as ‘0’. Shaded cells are not used by Timer0. Note 1: Reserved bits, do not use. DS41206A-page 28 Preliminary 2003 Microchip Technology Inc. PIC16F716 5.0 TIMER1 MODULE 5.1 The Timer1 module timer/counter has the following features: • 16-bit timer/counter (Two 8-bit registers; TMR1H and TMR1L) • Readable and writable (Both registers) • Internal or external clock select • Interrupt on overflow from FFFFh to 0000h • Reset from ECCP module trigger Timer1 can operate in one of these modes: • As a timer • As a synchronous counter • As an asynchronous counter The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). Timer1 has a control register, shown in Register 5-1. Timer1 can be enabled/disabled by setting/clearing control bit TMR1ON (T1CON<0>). Figure 5-1 is a simplified block diagram of the Timer1 module. Additional information on timer modules is available in the PICmicro® Mid-Range Reference Manual, (DS33023). REGISTER 5-1: Timer1 Operation In Timer mode, Timer1 increments every instruction cycle. In Counter mode, it increments on every rising edge of the external clock input. When the Timer1 oscillator is enabled (T1OSCEN is set), the RB2/T1OSI and RB1/T1OSO/T1CKI pins become inputs. That is, the TRISB<2:1> value is ignored. Timer1 also has an internal “Reset input”. This Reset can be generated by the ECCP module (Section 7.0 “Enhanced Capture/Compare/PWM (ECCP) Module”). T1CON: TIMER1 CONTROL REGISTER (ADDRESS: 10h) U-0 U-0 — — R/W-0 R/W-0 T1CKPS1 T1CKPS0 R/W-0 T1OSCEN R/W-0 R/W-0 R/W-0 T1SYNC TMR1CS TMR1ON bit 7 bit 0 bit 7-6 Unimplemented: Read as '0' bit 5-4 T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3 T1OSCEN: Timer1 Oscillator Enable Control bit 1 = Oscillator is enabled 0 = Oscillator is shut off(1) bit 2 T1SYNC: Timer1 External Clock Input Synchronization Control bit TMR1CS = 1 1 = Do not synchronize external clock input 0 = Synchronize external clock input TMR1CS = 0 This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. bit 1 TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin RB1/T1OSO/T1CKI (on the rising edge after the first falling edge) 0 = Internal clock (FOSC/4) bit 0 TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1 Note 1: The oscillator inverter and feedback resistor are turned off to eliminate power drain. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 29 PIC16F716 FIGURE 5-1: TIMER1 BLOCK DIAGRAM Set flag bit TMR1IF on Overflow Synchronized clock input 0 TMR1 TMR1L TMR1H 1 TMR1ON on/off T1SYNC T1OSC RB1/T1OSO/T1CKI 1 T1OSCEN FOSC/4 Enable Internal Oscillator(1) Clock RB2/T1OSI Note 1: 5.2 Synchronize Prescaler 1, 2, 4, 8 det 0 2 T1CKPS1:T1CKPS0 TMR1CS Sleep input When the T1OSCEN bit is cleared, the inverter and feedback resistor are turned off. This eliminates power drain. which is latched in interrupt flag bit TMR1IF (PIR1<0>). This interrupt can be enabled/disabled by setting/clearing TMR1 interrupt enable bit TMR1IE (PIE1<0>). Timer1 Oscillator A crystal oscillator circuit is built in between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting control bit T1OSCEN (T1CON<3>). The oscillator is a low-power oscillator designed to operate with a 32.768 kHz tuning fork crystal. It will continue to run during Sleep. 5.4 Resetting Timer1 using an ECCP Trigger Output If the ECCP module is configured in Compare mode to generate a “special event trigger” (CCP1M3:CCP1M0 = 1011), this signal will reset Timer1 and start an A/D conversion (if the A/D module is enabled). The user must provide a software time delay to ensure proper oscillator start-up. Note 1: Circuit guidelines for the LP oscillator (32 kHz), as shown in Section 9.2 “Oscillator Configurations”, also apply to the Timer1 Oscillator. Note: The special event triggers from the ECCP module will not set interrupt flag bit TMR1IF (PIR1<0>). 2: The Timer1 register pair, TMR1H and TMR1L, in combination with the Timer1 overflow flag (TMR1IF) can be used as the oscillator start-up stabilization timer. Timer1 must be configured for either Timer or Synchronized Counter mode to take advantage of this feature. If Timer1 is running in Asynchronous Counter mode, this Reset operation may not work. Timer1 Interrupt In the event that a write to Timer1 coincides with a special event trigger from the ECCP, the write will take precedence. 5.3 The TMR1 Register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The TMR1 interrupt, if enabled, is generated on overflow TABLE 5-1: Address In this mode of operation, the CCPR1H:CCPR1L register pair effectively becomes the period register for Timer1. REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER Name 0Bh,8Bh INTCON 0Ch PIR1 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other Resets Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u — ADIF — — — CCP1IF TMR2IF TMR1IF -0-- -000 -0-- -000 — ADIE — — — CCP1IE TMR2IE TMR1IE -0-- -000 -0-- -000 8Ch PIE1 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1 register xxxx xxxx uuuu uuuu 10h T1CON Legend: — — T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu x = unknown, u = unchanged, - = unimplemented read as ‘0’. Shaded cells are not used by the Timer1 module. DS41206A-page 30 Preliminary 2003 Microchip Technology Inc. PIC16F716 6.0 TIMER2 MODULE Figure 6-1 is a simplified block diagram of the Timer2 module. The Timer2 module timer has the following features: • • • • • • Additional information on timer modules is available in the PICmicro® Mid-Range Reference Manual, (DS33023). 8-bit timer (TMR2 register) 8-bit period register (PR2) Readable and writable (both registers) Software programmable prescaler (1:1, 1:4, 1:16) Software programmable postscaler (1:1 to 1:16) Interrupt on TMR2 match of PR2 Timer2 has a control register, shown in Register 6-1. Timer2 can be shut off by clearing control bit TMR2ON (T2CON<2>) to minimize power consumption. REGISTER 6-1: T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h) U-0 — R/W-0 R/W-0 R/W-0 TOUTPS3 TOUTPS2 TOUTPS1 R/W-0 TOUTPS0 R/W-0 R/W-0 R/W-0 TMR2ON T2CKPS1 T2CKPS0 bit 7 bit 0 bit 7 Unimplemented: Read as ‘0’ bit 6-3 TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale 0010 = 1:3 Postscale 0011 = 1:4 Postscale 0100 = 1:5 Postscale 0101 = 1:6 Postscale 0110 = 1:7 Postscale 0111 = 1:8 Postscale 1000 = 1:9 Postscale 1001 = 1:10 Postscale 1010 = 1:11 Postscale 1011 = 1:12 Postscale 1100 = 1:13 Postscale 1101 = 1:14 Postscale 1110 = 1:15 Postscale 1111 = 1:16 Postscale bit 2 TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off bit 1-0 T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16 Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 31 PIC16F716 6.1 Timer2 Operation 6.2 Timer2 can be used as the PWM time base for PWM mode of the ECCP module. Timer2 Interrupt The Timer2 module has an 8-bit Period register (PR2). Timer2 increments from 00h until it matches PR2 and then resets to 00h on the next increment cycle. PR2 is a readable and writable register. The PR2 register is initialized to FFh upon Reset. The TMR2 register is readable and writable, and is cleared on any device Reset The input clock (FOSC/4) has a prescale option of 1:1, 1:4 or 1:16, selected by control bits T2CKPS1:T2CKPS0 (T2CON<1:0>). FIGURE 6-1: Sets flag bit TMR2IF The match output of TMR2 goes through a 4-bit postscaler (which gives a 1:1 to 1:16 scaling inclusive) to generate a TMR2 interrupt (latched in flag bit TMR2IF, (PIR1<1>). TIMER2 BLOCK DIAGRAM TMR2 output Reset The prescaler and postscaler counters are cleared when any of the following occurs: Postscaler 1:1 to 1:16 • A write to the TMR2 register • A write to the T2CON register • Any device Reset (Power-on Reset, MCLR Reset, Watchdog Timer Reset, or Brown-out Reset) EQ 4 TMR2 reg Prescaler 1:1, 1:4, 1:16 FOSC/4 2 Comparator PR2 reg TMR2 is not cleared when T2CON is written. TABLE 6-1: REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER Address Name Bit 7 0Bh, 8Bh INTCON 0Ch PIR1 8Ch PIE1 11h TMR2 12h T2CON 92h PR2 Legend: Bit 2 Bit 0 Value on POR, BOR Value on all other Resets INTF RBIF 0000 000x 0000 000u TMR2IF TMR1IF -0-- -000 -0-- -000 TMR1IE -0-- -000 -0-- -000 0000 0000 0000 0000 -000 0000 -000 0000 1111 1111 1111 1111 Bit 6 Bit 5 Bit 4 Bit 3 Bit 1 GIE PEIE T0IE INTE RBIE T0IF — ADIF — — — CCP1IF — ADIE — — — CCP1IE TMR2IE — TOUTPS3 TOUTPS2 TOUTPS1 Timer2 module’s register TOUTPS0 TMR2ON Timer2 Period Register T2CKPS1 T2CKPS0 x = unknown, u = unchanged, - = unimplemented read as ‘0’. Shaded cells are not used by the Timer2 module. DS41206A-page 32 Preliminary 2003 Microchip Technology Inc. PIC16F716 7.0 ENHANCED CAPTURE/ COMPARE/PWM (ECCP) MODULE The CCP1CON register controls ECCP operation. All the CCP1CON bits are readable and writable. The ECCP (Enhanced Capture/Compare/PWM) module contains a 16-bit register, which can operate as: Additional information on the ECCP module is available in the PICmicro® Mid-Range Reference Manual, (DS33023). TABLE 7-1: • 16-bit Capture register • 16-bit Compare register • PWM Master/Slave Duty Cycle register ECCP MODE - TIMER RESOURCE ECCP Mode Table 7-1 shows the timer resources of the ECCP module modes. Timer Resource Capture Timer1 Compare Timer1 PWM Timer2 Capture/Compare/PWM Register 1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). REGISTER 7-1: CCP1CON REGISTER (ADDRESS: 17h) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 P1M1 P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 bit 7 bit 0 bit 7-6 P1M1:P1M0: PWM Output Configuration bits CCP1M<3:2> = 00, 01, 10 xx = P1A assigned as Capture/Compare I/O. P1B, P1C, P1D assigned as Port pins. CCP1M<3:2> = 11 00 = Single output, P1A modulated. P1B, P1C, P1D assigned as Port pins. 01 = Quad output forward. P1D modulated, P1A active. P1B and P1C inactive. 10 = Dual output. P1A, P1B modulated with dead-time control. P1C, P1D assigned as port pins. 11 = Quad output reverse. P1B modulated, P1C active. P1A and P1D inactive. bit 5-4 DC1B1:DC1B0: PWM Least Significant bits Capture mode: Unused Compare mode: Unused PWM mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L. bit 3-0 CCP1M3:CCP1M0: ECCP Mode Select bits 0000 = Capture/Compare/PWM off (resets ECCP module) 0001 = Unused (Reserved) 0010 = Compare mode, toggle output on match (CCP1IF bit is set) 0011 = Unused (Reserved) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set CCP1 output on match (CCP1IF bit is set) 1001 = Compare mode, clear CCP1 output on match (CCP1IF bit is set) 1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is unaffected) 1011 = Compare mode, trigger special event (CCP1IF bit is set, TMR1 is reset, and an A/D conversion is started if the A/D module is enabled. CCP1 pin is unaffected). 1100 = PWM mode. P1A, P1C active-high; P1B, P1D active-high. 1101 = PWM mode. P1A, P1C active-high; P1B, P1D active-low. 1110 = PWM mode. P1A, P1C active-low; P1B, P1D active-high. 1111 = PWM mode. P1A, P1C active-low; P1B, P1D active-low. Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 33 PIC16F716 7.1 7.1.4 Capture Mode In Capture mode, CCPR1H:CCPR1L captures the 16-bit value of the TMR1 register when an event occurs on pin RB3/CCP1/P1A. An event is defined as: • • • • Every falling edge Every rising edge Every 4th rising edge Every 16th rising edge An event is selected by control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). When a capture is made, the interrupt request flag bit CCP1IF (PIR1<2>) is set. It must be cleared in software. If another capture occurs before the value in register CCPR1 is read, the old captured value will be lost. Note: Always reset the ECCP module (CCP1M3:CCP1M0 = ‘0000’) between changing from one capture mode to another. This is necessary to reset the internal capture counter. FIGURE 7-1: CAPTURE MODE OPERATION BLOCK DIAGRAM Prescaler 1, 4, 16 RB3/CCP1/P1A Pin CCPR1H and edge detect CCPR1L TMR1L CCP1CON<3:0> Q’s 7.1.1 7.1.2 EXAMPLE 7-1: CLRF MOVLW CCP1CON NEW_CAPT_PS MOVWF CCP1CON CHANGING BETWEEN CAPTURE PRESCALERS ;Turn ECCP module off ;Load the W reg with ;the new prescaler ;mode value and ECCP ON ;Load CCP1CON with this ;value Compare Mode In Compare mode, the 16-bit CCPR1 register value is constantly compared against the TMR1 register pair value. When a match occurs, the RB3/CCP1/P1A pin is either: Driven High Driven Low Toggle output (high-to-low or low-to-high) Remains Unchanged The action on the pin is based on the value of control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). At the same time, interrupt flag bit CCP1IF is set. CCP1 PIN CONFIGURATION In Capture mode, the RB3/CCP1/P1A pin should be configured as an input by setting the TRISB<3> bit. Note: Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore, the first capture may be from a non-zero prescaler. Example 7-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the “false” interrupt. • • • • Capture Enable TMR1H There are four prescaler settings, specified by bits CCP1M3:CCP1M0. Whenever the ECCP module is turned off, or the ECCP module is not in Capture mode, the prescaler counter is cleared. This means that any Reset will clear the prescaler counter. 7.2 Set flag bit CCP1IF (PIR1<2>) ECCP PRESCALER If the RB3/CCP1/P1A is configured as an output, a write to PORTB can cause a capture condition. Changing the ECCP mode to clear output on match (CCP1M<3:0> = 1000) presets the CCP1 output latch to the logic 1 level. Changing the ECCP mode to set output on match (CCP1M<3:0> = 1001) presets the CCP1 output latch to the logic 0 level. TIMER1 MODE SELECTION Timer1 must be running in Timer mode or Synchronized Counter mode for the ECCP module to use the capture feature. In Asynchronous Counter mode, the capture operation may not work. 7.1.3 SOFTWARE INTERRUPT When the Capture mode is changed, a false capture interrupt may be generated. The user should keep bit CCP1IE (PIE1<2>) clear to avoid false interrupts and should clear the flag bit CCP1IF following any such change in operating mode. DS41206A-page 34 Preliminary 2003 Microchip Technology Inc. PIC16F716 7.2.1 CCP1 PIN CONFIGURATION The user must configure the RB3/CCP1/P1A pin as the CCP1 output by clearing the TRISB<3> bit. Note: 7.2.2 Note: Clearing the CCP1CON register will force the RB3/CCP1/P1A compare output latch to the default low level. This is not the PORTB I/O data latch. The special event trigger from the ECCP module will not set interrupt flag bit TMR1IF (PIR1<0>). FIGURE 7-2: COMPARE MODE OPERATION BLOCK DIAGRAM TIMER1 MODE SELECTION Special Event Trigger Timer1 must be running in Timer mode or Synchronized Counter mode if the ECCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. Set flag bit CCP1IF (PIR1<2>) RB3/CCP1/P1A Pin CCPR1H CCPR1L Q S R 7.2.3 SOFTWARE INTERRUPT MODE TRISB<3> Output Enable When Generate Software Interrupt mode is chosen, the CCP1 pin is not affected. Only a CCP interrupt is generated (if enabled). 7.2.4 Note 1: SPECIAL EVENT TRIGGER Output Logic Comparator match TMR1H CCP1CON<3:0> Mode Select TMR1L Special event trigger will reset Timer1, but not set interrupt flag bit TMR1IF (PIR1<0>), and set bit GO/ DONE (ADCON0<2>) which starts an A/D conversion. In this mode, an internal hardware trigger is generated which may be used to initiate an action. The special event trigger output of the ECCP resets the TMR1 register pair. This allows the CCPR1 register to effectively be a 16-bit programmable period register for Timer1. The special event trigger output of the ECCP also starts an A/D conversion (if the A/D module is enabled). TABLE 7-2: Address REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, AND TIMER1 Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 GIE PEIE T0IE INTE RBIE T0IF — ADIF — — — CCP1IF Bit 0 Value on POR, BOR INTF RBIF 0000 000x 0000 000u TMR2IF TMR1IF -0-- -000 -0-- -000 xxxx xxxx uuuu uuuu Bit 2 Bit 1 0Bh,8Bh INTCON 0Ch PIR1 0Eh TMR1L Holding register for the Least Significant Byte of the 16-bit TMR1 register 0Fh TMR1H Holding register for the Most Significant Byte of the 16-bit TMR1register 10h T1CON 15h CCPR1L 16h CCPR1H 17h CCP1CON 86h TRISB 8Ch PIE1 Legend: Value on all other Resets xxxx xxxx uuuu uuuu --00 0000 --uu uuuu Capture/Compare/PWM register1 (LSB) xxxx xxxx uuuu uuuu Capture/Compare/PWM register1 (MSB) xxxx xxxx uuuu uuuu 0000 0000 0000 0000 1111 1111 1111 1111 -0-- -000 -0-- -000 — P1M1 — P1M0 T1CKPS1 DC1B1 T1CKPS0 DC1B0 T1OSCEN CCP1M3 T1SYNC CCP1M2 TMR1CS CCP1M1 TMR1ON CCP1M0 PORTB Data direction register — ADIE — — — CCP1IE TMR2IE TMR1IE x = unknown, u = unchanged, - = unimplemented read as ‘0’. Shaded cells are not used by Capture and Timer1. 2003 Microchip Technology Inc. Preliminary DS41206A-page 35 PIC16F716 7.3 PWM Mode In Pulse Width Modulation (PWM) mode, the CCP1 pin produces up to a 10-bit resolution PWM output. Since the CCP1 pin is multiplexed with the PORTB data latch, the TRISB<3> bit must be cleared to make the CCP1 pin an output. Note: A PWM output (Figure 7-4) has a time base (period) and a time that the output stays high (duty cycle). The frequency of the PWM is the inverse of the period (1/period). FIGURE 7-4: Clearing the CCP1CON register will force the CCP1 PWM output latch to the default low level. This is not the PORTB I/O data latch. Period = PR2+1 Duty Cycle Figure 7-3 shows a simplified block diagram of the CCP module in PWM mode. TMR2 = PR2 For a step-by-step procedure on how to setup the ECCP module for PWM operation, see Section 7.3.3 “Set-Up for PWM Operation”. FIGURE 7-3: SIMPLIFIED PWM BLOCK DIAGRAM Duty cycle registers PWM OUTPUT TMR2 = Duty Cycle (CCPR1H) TMR2 = PR2 7.3.1 PWM PERIOD The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: CCP1CON<5:4> CCPR1L EQUATION 7-1: PWM Period = [(PR2) + 1] • 4 • Tosc • (TMR2 prescale value) CCPR1H (Slave) RB3/CCP1/P1A R Comparator TMR2 When TMR2 is equal to PR2, the following three events occur on the next increment cycle: S • TMR2 is cleared • The CCP1 pin is set (exception: if PWM duty cycle = 0%, the CCP1 pin will not be set) • The PWM duty cycle is latched from CCPR1L into CCPR1H TRISB<3> Clear Timer, CCP1 pin and latch D.C. PR2 1: PWM frequency is defined as 1/[PWM period]. (Note 1) Comparator Note Q 8-bit timer is concatenated with 2-bit internal Q clock or 2 bits of the prescaler to create 10-bit time base. Note: DS41206A-page 36 Preliminary The Timer2 postscaler (see Section 6.0 “Timer2 Module”) is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. 2003 Microchip Technology Inc. PIC16F716 7.3.2 PWM DUTY CYCLE EQUATION 7-3: The PWM duty cycle is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available. The CCPR1L contains the eight MSbs and the CCP1CON<5:4> contains the two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. The following equation is used to calculate the PWM duty cycle in time: log Max resolution = Note: If the PWM duty cycle value is longer than the PWM period the CCP1 pin will not be cleared. For an example PWM period and duty cycle calculation, see the PICmicro® Mid-Range Reference Manual, (DS33023). PWM Duty Cycle = (CCPR1L:CCP1CON<5:4> • TOSC • (TMR2 prescale value) CCPR1L and CCP1CON<5:4> can be written to at any time, but the duty cycle value is not latched into CCPR1H until a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. 7.3.3 SET-UP FOR PWM OPERATION The following steps should be taken when configuring the ECCP module for PWM operation: 1. The CCPR1H register and a 2-bit internal latch are used to double buffer the PWM duty cycle. This double buffering is essential for glitchless PWM operation. Set the PWM period by writing to the PR2 register. Set the PWM duty cycle by writing to the CCPR1L register and CCP1CON<5:4> bits. Make the CCP1 pin an output by clearing the TRISB<3> bit. Set the TMR2 prescale value and enable Timer2 by writing to T2CON. Configure the CCP1 module for PWM operation. 2. 3. When the CCPR1H and 2-bit latch match TMR2 concatenated with an internal 2-bit Q clock or 2 bits of the TMR2 prescaler, the CCP1 pin is cleared. 4. Maximum PWM resolution (bits) for a given PWM frequency is given by the following equation: 5. EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 20 MHz PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits) TABLE 7-4: Address bits log(2) EQUATION 7-2: TABLE 7-3: OSC ( FFPWM ) 16 0xFF 10 4 0xFF 10 1 0xFF 10 1 0x3F 8 1 0x1F 7 1 0x17 6.6 REGISTERS ASSOCIATED WITH PWM AND TIMER2 Bit 1 Bit 0 Value on all other Resets Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 0Ch PIR1 — ADIF — — — CCP1IF TMR2IF TMR1IF -0-- -000 -0-- -000 11h TMR2 0000 0000 0000 0000 12h T2CON T2CKPS1 T2CKPS0 -000 0000 -000 0000 15h CCPR1L Capture/Compare/PWM register1 (LSB) xxxx xxxx uuuu uuuu 16h CCPR1H Capture/Compare/PWM register1 (MSB) xxxx xxxx uuuu uuuu 17h CCP1CON 0000 0000 0000 0000 86h TRISB 1111 1111 1111 1111 8Ch PIE1 -0-- -000 -0-- -000 92h PR2 1111 1111 1111 1111 Legend: Bit 2 Value on POR, BOR Name Timer2 module’s register — P1M1 TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON P1M0 DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 PORB Data direction register — ADIE — — — Timer2 module’s period register CCP1IE TMR2IE TMR1IE x = unknown, u = unchanged, - = unimplemented read as ‘0’. Shaded cells are not used by PWM and Timer2. 2003 Microchip Technology Inc. Preliminary DS41206A-page 37 PIC16F716 7.4 7.4.1 ENHANCED PWM MODE PWM OUTPUT CONFIGURATIONS The P1M1:P1M0 bits in the CCP1CON register allows one of four configurations: The Enhanced PWM mode provides additional PWM output options for a broader range of control applications. The module is an upwardly compatible version of the standard CCP module and offers up to four outputs, designated P1A through P1D. Users are also able to select the polarity of the signal (either active-high or active-low). The module’s Output mode and polarity are configured by setting the P1M1:P1M0 and CCP1M3:CCP1M0 bits of the CCP1CON register (CCP1CON<7:6> and CCP1CON<3:0>, respectively). • • • • Single Output Half-Bridge Output Full-Bridge Output Forward mode Full-Bridge Output Reverse mode The Single Output mode is the Standard PWM mode discussed in Section 7.3 “PWM Mode”. The HalfBridge and Full-Bridge Output modes are covered in detail in the sections that follow. Figure 7-5 shows a simplified block diagram of PWM operation. All control registers are double buffered and are loaded at the beginning of a new PWM cycle (the period boundary when Timer2 resets) in order to prevent glitches on any of the outputs. The exception is the PWM Dead-band Delay, which is loaded at either the duty cycle boundary or the boundary period (whichever comes first). Because of the buffering, the module waits until the assigned timer resets, instead of starting immediately. This means that enhanced PWM waveforms do not exactly match the standard PWM waveforms, but are instead offset by one full instruction cycle (4 TOSC). The general relationship of the outputs in all configurations is summarized in Figure 7-6. As before, the user must manually configure the appropriate TRISB bits for output. FIGURE 7-5: SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODULE CCP1CON<5:4> Duty Cycle Registers CCP1M<3:0> 4 P1M<1:0> 2 CCPR1L CCP1/P1A RB3/CCP1/P1A TRISB<3> CCPR1H (Slave) P1B R Comparator Q Output Controller RB5/P1B TRISB<5> RB6/P1C P1C (Note 1) TMR2 TRISB<6> S P1D Comparator Clear Timer, set CCP1 pin and latch D.C. PR2 Note 1: RB7/P1D TRISB<7> PWM1CON The 8-bit timer TMR2 register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler to create the 10-bit time base. DS41206A-page 38 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 7-6: PWM OUTPUT RELATIONSHIPS (P1A, P1B, P1C, P1D ACTIVE-HIGH STATE) 0 00 PR2+1 Duty Cycle SIGNAL CCP1CON <7:6> Period (Single Output) P1A Modulated Delay(1) Delay(1) P1A Modulated 10 (Half-Bridge) P1B Modulated P1A Active 01 P1B Inactive (Full-Bridge, Forward) P1C Inactive P1D Modulated P1A Inactive 11 P1B Modulated (Full-Bridge, Reverse) P1C Active P1D Inactive FIGURE 7-7: PWM OUTPUT RELATIONSHIPS (P1A, P1B, P1C, P1D ACTIVE-LOW STATE) 0 00 (Single Output) PR2+1 Duty Cycle SIGNAL CCP1CON <7:6> Period P1A Modulated P1A Modulated 10 (Half-Bridge) Delay(1) Delay(1) P1B Modulated P1A Active 01 (Full-Bridge, Forward) P1B Inactive P1C Inactive P1D Modulated P1A Inactive 11 (Full-Bridge, Reverse) P1B Modulated P1C Active P1D Inactive Relationships: • Period = 4 * TOSC * (PR2 + 1) * (TMR2 prescale value) • Duty Cycle = TOSC * (CCPR1L<7:0> : CCP1CON<5:4>) * (TMR2 prescale value) • Delay = 4 * TOSC * (PWM1CON<6:0>) Note 1: Dead-band delay is programmed using the PWM1CON register (Section 7.4.4 “Programmable Dead-Band Delay”). 2003 Microchip Technology Inc. Preliminary DS41206A-page 39 PIC16F716 FIGURE 7-8: PWM OUTPUT RELATIONSHIPS (P1A, P1C ACTIVE-HIGH. P1B, P1D ACTIVE-LOW) 0 CCP1CON <7:6> 00 (Single Output) PR2+1 Duty Cycle SIGNAL Period P1A Modulated Delay(1) Delay(1) P1A Modulated 10 (Half-Bridge) P1B Modulated P1A Active 01 (Full-Bridge, Forward) P1B Inactive P1C Inactive P1D Modulated P1A Inactive 11 (Full-Bridge, Reverse) P1B Modulated P1C Active P1D Inactive DS41206A-page 40 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 7-9: PWM OUTPUT RELATIONSHIPS (P1A, P1C ACTIVE-LOW. P1B, P1D ACTIVE-HIGH) 0 00 (Single Output) PR2+1 Duty Cycle SIGNAL CCP1CON <7:6> Period P1A Modulated P1A Modulated 10 (Half-Bridge) Delay(1) Delay(1) P1B Modulated P1A Active 01 (Full-Bridge, Forward) P1B Inactive P1C Inactive P1D Modulated P1A Inactive 11 (Full-Bridge, Reverse) P1B Modulated P1C Active P1D Inactive Relationships: • Period = 4 * TOSC * (PR2 + 1) * (TMR2 prescale value) • Duty Cycle = TOSC * (CCPR1L<7:0> : CCP1CON<5:4>) * (TMR2 prescale value) • Delay = 4 * TOSC * (PWM1CON<6:0>) Note 1: Dead-band delay is programmed using the PWM1CON register (Section 7.4.4 “Programmable Dead-Band Delay”). 2003 Microchip Technology Inc. Preliminary DS41206A-page 41 PIC16F716 7.4.2 HALF-BRIDGE MODE In the Half-Bridge Output mode, two pins are used as outputs to drive push-pull loads. The PWM output signal is output on the RB3/CCP1/P1A pin, while the complementary PWM output signal is output on the RB5/P1B pin (Figure 7-12). This mode can be used for half-bridge applications, as shown in Figure 7-11 or for full-bridge applications, where four power switches are being modulated with two PWM signals. In Half-Bridge Output mode, the programmable deadband delay can be used to prevent shoot-through current in half-bridge power devices. The value of PWM1CON bits PDC6:PDC0 sets the number of instruction cycles before the output is driven active. If the value is greater than the duty cycle, the corresponding output remains inactive during the entire cycle. See Section 7.4.4 “Programmable DeadBand Delay” for more details of the dead-band delay operations. Since the P1A and P1B outputs are multiplexed with the PORTB<3> and PORTB<5> data latches, the TRISB<3> and TRISB<5> bits must be cleared to configure P1A and P1B as outputs. FIGURE 7-10: Period Period Duty Cycle (2) P1A td td P1B(2) (1) (1) (1) td = Dead-band Delay Note 1: 2: FIGURE 7-11: HALF-BRIDGE PWM OUTPUT At this time, the TMR2 register is equal to the PR2 register. Output signals are shown as active-high. EXAMPLES OF HALF-BRIDGE OUTPUT MODE APPLICATIONS V+ Standard Half-Bridge Circuit (“Push-Pull”) PIC16F716 FET Driver + V - P1A Load FET Driver + V - P1B V- Half-Bridge Output Driving a Full-Bridge Circuit V+ PIC16F716 FET Driver FET Driver P1A FET Driver Load FET Driver P1B V- DS41206A-page 42 Preliminary 2003 Microchip Technology Inc. PIC16F716 7.4.3 FULL-BRIDGE MODE P1A, P1B, P1C and P1D outputs are multiplexed with the PORTB<3> and PORTB<5:7> data latches. The TRISB<3> and TRISB<5:7> bits must be cleared to make the P1A, P1B, P1C, and P1D pins output. In Full-Bridge Output mode, four pins are used as outputs; however, only two outputs are active at a time. In the Forward mode, pin RB3/CCP1/P1A is continuously active, and pin RB7/P1D is modulated. In the Reverse mode, RB6/P1C pin is continuously active, and RB5/P1B pin is modulated. These are illustrated in Figure 7-6 through Figure 7-9. FIGURE 7-12: EXAMPLE OF FULL-BRIDGE APPLICATION V+ PIC16F716 FET Driver QC QA FET Driver P1A Load P1B FET Driver P1C FET Driver QD QB VP1D 7.4.3.1 Direction Change in Full-Bridge Mode Note: In the Full-Bridge Output mode, the P1M1 bit in the CCP1CON register allows the user to control the Forward/Reverse direction. When the application firmware changes this direction control bit, the module will assume the new direction on the next PWM cycle. Just before the end of the current PWM period, the modulated outputs (P1B and P1D) are placed in their inactive state, while the unmodulated outputs (P1A and P1C) are switched to drive in the opposite direction. This occurs in a time interval of (4•TOSC•(Timer2 Prescale value)) before the next PWM period begins. The Timer2 prescaler will be either 1, 4 or 16, depending on the value of the T2CKPSx bits (T2CON<1:0>). During the interval from the switch of the unmodulated outputs to the beginning of the next period, the modulated outputs (P1B and P1D) remain inactive. This relationship is shown in Figure 7-13. 2003 Microchip Technology Inc. Preliminary In the Full-Bridge Output mode, the ECCP module does not provide any dead-band delay. In general, since only one output is modulated at all times, dead-band delay is not required. However, there is a situation where a dead-band delay might be required. This situation occurs when both of the following conditions are true: 1. The direction of the PWM output changes when the duty cycle of the output is at or near 100%. 2. The turn off time of the power switch, including the power device and driver circuit, is greater than the turn on time. DS41206A-page 43 PIC16F716 Figure 7-14 shows an example where the PWM direction changes from forward to reverse, at a near 100% duty cycle. At time t1, the output P1A and P1D become inactive, while output P1C becomes active. In this example, since the turn-off time of the power devices is longer than the turn-on time, a shoot-through current may flow through power devices QC and QD (see Figure 7-12) for the duration of ‘t’. The same phenomenon will occur to power devices QA and QB for PWM direction change from reverse to forward. FIGURE 7-13: If changing PWM direction at high duty cycle is required for an application, one of the following requirements must be met: 1. 2. Reduce PWM for a PWM period before changing directions. Use switch drivers that can drive the switches off faster than they can drive them on. Other options to prevent shoot-through current may exist. PWM DIRECTION CHANGE Period(1) SIGNAL Period P1A (Active-High) P1B (Active-High) DC P1C (Active-High) (Note 2) P1D (Active-High) DC Note 1: 2: The direction bit in the CCP1 Control Register (CCP1CON<7>) is written any time during the PWM cycle. When changing directions, the P1A and P1C signals switch before the end of the current PWM cycle at intervals of 4 TOSC, 16 TOSC or 64 TOSC, depending on the Timer2 prescaler value. The modulated P1B and P1D signals are inactive at this time. FIGURE 7-14: PWM DIRECTION CHANGE AT NEAR 100% DUTY CYCLE Forward Period t1 Reverse Period P1A P1B DC P1C P1D DC ton External Switch C toff External Switch D Potential Shoot-Through Current Note 1: 2: 3: t = toff - ton All signals are shown as active-high. ton is the turn-on delay of power switch QC and its driver. toff is the turn-off delay of power switch QD and its driver. DS41206A-page 44 Preliminary 2003 Microchip Technology Inc. PIC16F716 7.4.4 PROGRAMMABLE DEAD-BAND DELAY 7.4.5 In half-bridge applications where all power switches are modulated at the PWM frequency at all times, the power switches normally require more time to turn off than to turn on. If both the upper and lower power switches are switched at the same time (one turned on, and the other turned off), both switches may be on for a short period of time until one switch completely turns off. During this brief interval, a very high current (shootthrough current) may flow through both power switches, shorting the bridge supply. To avoid this potentially destructive shoot-through current from flowing during switching, turning on either of the power switches is normally delayed to allow the other switch to completely turn off. In the Half-Bridge Output mode, a digitally programmable dead-band delay is available to avoid shootthrough current from destroying the bridge power switches. The delay occurs at the signal transition from the non-active state to the active state. See Figure 7-10 for illustration. The lower seven bits of the PWM1CON register (Register 7-2) sets the delay period in terms of microcontroller instruction cycles (TCY or 4 TOSC). ENHANCED PWM AUTO-SHUTDOWN When the ECCP is programmed for any of the enhanced PWM modes, the active output pins may be configured for auto-shutdown. Auto-shutdown immediately places the enhanced PWM output pins into a defined shutdown state when a shutdown event occurs. A shutdown event can be caused by a logic low level on either or both of the RB0/INT/ECCPAS2 or RB4/ ECCPAS0 pins. The auto-shutdown feature can be disabled by not selecting any auto-shutdown sources. The auto-shutdown sources to be used are selected using the ECCPAS2 and ECCPAS0 bits (ECCPAS<6> and ECCPAS<4>). When a shutdown occurs, the output pins are asynchronously placed in their shutdown states, specified by the PSSAC1:PSSAC0 and PSSBD1:PSSBD0 bits (ECCPAS<3:0>). Each pin pair (P1A/P1C and P1B/P1D) may be set to drive high, drive low, or be tri-stated (not driving). The ECCPASE bit (ECCPAS<7>) is also set to hold the enhanced PWM outputs in their shutdown states. The ECCPASE bit is set by hardware when a shutdown event occurs. If automatic restarts are not enabled, the ECCPASE bit must be cleared by firmware when the cause of the shutdown clears. If automatic restarts are enabled, the ECCPASE bit is automatically cleared when the cause of the auto-shutdown has cleared. If the ECCPASE bit is set when a PWM period begins, the PWM outputs remain in their shutdown state for that entire PWM period. When the ECCPASE bit is cleared, the PWM outputs will return to normal operation at the beginning of the next PWM period. Note: 2003 Microchip Technology Inc. Preliminary Writing to the ECCPASE bit is disabled while a shutdown condition is active. DS41206A-page 45 PIC16F716 REGISTER 7-2: PWM1CON: PWM CONFIGURATION REGISTER (ADDRESS: 18h) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 PRSEN PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 bit 7 bit 0 bit 7 PRSEN: PWM Restart Enable bit 1 = Upon auto-shutdown, the ECCPASE bit clears automatically once the shutdown event goes away; the PWM restarts automatically. 0 = Upon auto-shutdown, ECCPASE must be cleared in firmware to restart the PWM. bit 6-0 PDC<6:0>: PWM Delay Count bits Number of FOSC/4 (4*TOSC) cycles between the scheduled time when a PWM signal should transition active, and the actual time it transitions active. Legend: REGISTER 7-3: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared x = Bit is unknown ECCPAS – ENHANCED CCP AUTO SHUT DOWN REGISTER (ADDRESS: 19h) R/W-0 R/W-0 ECCPASE ECCPAS2 U-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 — ECCPAS0 PSSAC1 PSSAC0 PSSBD1 PSSBD0 bit 7 bit 0 bit 7 ECCPASE: ECCP Auto-Shutdown Event Status bit 1 = A shutdown event has occurred. Must be reset in firmware to re-enable ECCP if PRSEN = 0 0 = ECCP outputs enabled, no shutdown event bit 6 ECCPAS2: ECCP Auto-Shutdown bit 2 1 = RB0 (INT) pin low level (‘0’) causes shutdown 0 = RB0 (INT) pin has no effect on ECCP bit 5 Unimplemented: Read as ‘0’ bit 4 ECCPAS0: ECCP Auto-Shutdown bit ‘0’ 1 = RB4 pin low level (‘0’) causes shutdown 0 = RB4 pin has no effect on ECCP bit 3-2 PSSAC<1:0>: Pin P1A and P1C Shutdown State Control 00 = Drive Pins P1A and P1C to ‘0’ 01 = Drive Pins P1A and P1C to ‘1’ 1x = Pins P1A and P1C tri-state bit 1-0 PSSBD<1:0>: Pin P1B and P1D Shutdown State Control 00 = Drive Pins P1B and P1D to ‘0’ 01 = Drive Pins P1B and P1D to ‘1’ 1x = Pins P1B and P1D tri-state Legend: DS41206A-page 46 R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ - n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared Preliminary x = Bit is unknown 2003 Microchip Technology Inc. PIC16F716 7.4.5.1 Auto-Shutdown and Automatic Restart 7.4.6 The auto-shutdown feature can be configured to allow automatic restarts of the module following a shutdown event. This is enabled by setting the PRSEN bit of the PWM1CON register (PWM1CON<7>). In Shutdown mode with PRSEN = 1 (PWM1CON <7>) (Figure 7-15), the ECCPASE bit will remain set for as long as the cause of the shutdown continues. When the shutdown condition clears, the ECCPASE bit is cleared. If PRSEN = 0 (Figure 7-16), once a shutdown condition occurs, the ECCPASE bit will remain set until it is cleared by firmware. Once ECCPASE is cleared, the enhanced PWM will resume at the beginning of the next PWM period. Note: Writing to the ECCPASE bit is disabled while a shutdown condition is active. The ECCPASE bit cannot be cleared as long as the cause of the shutdown persists. The Auto-shutdown mode can be forced by writing a '1' to the ECCPASE bit. FIGURE 7-15: START-UP CONSIDERATIONS When the ECCP module is used in the PWM mode, the application hardware must use the proper external pullup and/or pull-down resistors on the PWM output pins. When the microcontroller is released from Reset, all of the I/O pins are in the high-impedance state. The external circuits must keep the power switch devices in the off state, until the microcontroller drives the I/O pins with the proper signal levels, or activates the PWM output(s). The CCP1M1:CCP1M0 bits (CCP1CON<1:0>) allow the user to choose whether the PWM output signals are active-high or active-low for each pair of PWM output pins (P1A/P1C and P1B/P1D). The PWM output polarities must be selected before the PWM pins are configured as outputs. Changing the polarity configuration while the PWM pins are configured as outputs is not recommended since it may result in damage to the application circuits. The P1A, P1B, P1C and P1D output latches may not be in the proper states when the PWM module is initialized. Enabling the PWM pins for output at the same time as the ECCP module may cause damage to the application circuit. The ECCP module must be enabled in the proper Output mode and complete a full PWM cycle before configuring the PWM pins as outputs. The completion of a full PWM cycle is indicated by the TMR2IF bit being set as the second PWM period begins. PWM AUTO-SHUTDOWN (PRSEN = 1, AUTO-RESTART ENABLED) PWM Period Shutdown Event ECCPASE bit PWM Activity Normal PWM Start of PWM Period FIGURE 7-16: Shutdown Shutdown Event Occurs Event Clears PWM Resumes PWM AUTO-SHUTDOWN (PRSEN = 0, AUTO-RESTART DISABLED) PWM Period Shutdown Event ECCPASE bit PWM Activity Normal PWM Start of PWM Period 2003 Microchip Technology Inc. ECCPASE Cleared by Shutdown Shutdown Firmware PWM Event Occurs Event Clears Resumes Preliminary DS41206A-page 47 PIC16F716 7.4.7 SETUP FOR PWM OPERATION 8. Configure and start TMR2: The following steps should be taken when configuring the ECCP module for PWM operation: • Clear the TMR2 interrupt flag bit by clearing the TMR2IF bit (PIR1<1>). 1. • Set the TMR2 prescale value by loading the T2CKPSx bits (T2CON<1:0>). 2. 3. Configure the PWM pins P1A and P1B (and P1C and P1D, if used) as inputs by setting the corresponding TRISB bits. Set the PWM period by loading the PR2 register. Configure the ECCP module for the desired PWM mode and configuration by loading the CCP1CON register with the appropriate values: • Enable Timer2 by setting the TMR2ON bit (T2CON<2>). 9. • Wait until TMR2 overflows (TMR2IF bit is set). • Select one of the available output configurations and direction with the P1M1:P1M0 bits. • Enable the CCP1/P1A, P1B, P1C and/or P1D pin outputs by clearing the respective TRISB bits. • Select the polarities of the PWM output signals with the CCP1M3:CCP1M0 bits. 4. 5. 6. Enable PWM outputs after a new PWM cycle has started: • Clear the ECCPASE bit (ECCPAS<7>). See the previous section for additional details. Set the PWM duty cycle by loading the CCPR1L register and CCP1CON<5:4> bits. For Half-Bridge Output mode, set the deadband delay by loading PWM1CON<6:0> with the appropriate value. If auto-shutdown operation is required, load the ECCPAS register. 7.4.8 EFFECTS OF A RESET Both Power-on and subsequent Resets will force all ports to Input mode and the ECCP registers to their Reset states. This forces the Enhanced CCP module to reset to a state compatible with the standard ECCP module. • Select the auto-shutdown sources using the ECCPAS<2> AND ECCPAS<0> bits. • Select the shutdown states of the PWM output pins using PSSAC1:PSSAC0 and PSSBD1:PSSBD0 bits. • Set the ECCPASE bit (ECCPAS<7>). 7. If auto-restart operation is required, set the PRSEN bit (PWM1CON<7>). TABLE 7-5: Address REGISTERS ASSOCIATED WITH ENHANCED PWM AND TIMER2 Name Bit 7 0Bh INTCON 0Ch PIR1 8Ch PIE1 11h TMR2 Timer2 Module Register 92h PR2 Timer2 Module Period Register 12h T2CON Value on POR, BOR INT0IF RBIF 0000 000x 0000 000u TMR2IF TMR1IF -0-- -000 -0-- -000 TMR1IE -0-- --00 -0-- --00 Bit 5 Bit 4 Bit 3 Bit 2 GIE PEIE TMR0IE INT0IE RBIE TMR0IF — ADIF — — — CCP1IF — ADIE — — — CCP1IE TMR2IE — TOUTPS3 Value on all other Resets Bit 0 Bit 6 Bit 1 0000 0000 0000 0000 1111 1111 1111 1111 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 86h TRISB PORTB Data Direction Register 1111 1111 1111 1111 16h CCPR1H Enhanced Capture/Compare/PWM Register1 High Byte xxxx xxxx uuuu uuuu 15h CCPR1L Enhanced Capture/Compare/PWM Register1 Low Byte 17h CCP1CON 19h ECCPAS 18h PWM1CON Legend: P1M1 P1M0 ECCPASE PRSEN xxxx xxxx uuuu uuuu DC1B1 DC1B0 CCP1M3 CCP1M2 CCP1M1 CCP1M0 0000 0000 0000 0000 ECCPAS2 — ECCPAS0 PSSAC1 PSSAC0 PSSBD1 PSSBD0 00-0 0000 00-0 0000 PDC6 PDC5 PDC4 PDC3 PDC2 PDC1 PDC0 0000 0000 0000 0000 x = unknown, u = unchanged, - = unimplemented, read as ‘0’. Shaded cells are not used by the ECCP module in enhanced PWM mode. DS41206A-page 48 Preliminary 2003 Microchip Technology Inc. PIC16F716 8.0 ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE Additional information on the A/D module is available in the PICmicro® Mid-Range Reference Manual, (DS33023). The Analog-to-Digital (A/D) Converter module has four inputs. The A/D module has three registers. These registers are: The A/D allows conversion of an analog input signal to a corresponding 8-bit digital number (refer to Application Note AN546 for use of A/D Converter). The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is software selectable to either the device’s positive supply voltage (VDD) or the voltage level on the RA3/ AN3/VREF pin. • A/D Result Register (ADRES) • A/D Control Register 0 (ADCON0) • A/D Control Register 1 (ADCON1) A device Reset forces all registers to their Reset state. This forces the A/D module to be turned off and any conversion is aborted. The ADCON0 register, shown in Register 8-1, controls the operation of the A/D module. The ADCON1 register, shown in Register 8-2, configures the functions of the port pins. The port pins can be configured as analog inputs (RA3 can also be a voltage reference) or as digital I/O. The A/D converter has a unique feature of being able to operate while the device is in Sleep mode. To operate in Sleep, the A/D conversion clock must be derived from the A/D’s internal RC oscillator. REGISTER 8-1: ADCON0 REGISTER (ADDRESS: 1Fh) R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE — ADON bit 7 bit 0 bit 7-6 ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (Clock derived from the internal ADC RC oscillator) bit 5-3 CHS2:CHS0: Analog Channel Select bits 000 = channel 0, (RA0/AN0) 001 = channel 1, (RA1/AN1) 010 = channel 2, (RA2/AN2) 011 = channel 3, (RA3/AN3) 1xx = reserved, do not use bit 2 GO/DONE: A/D Conversion Status bit If ADON = 1 1 = A/D conversion in progress (Setting this bit starts the A/D conversion) 0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D conversion is complete) bit 1 Reserved: Maintain this bit as '0' bit 0 ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shutoff and consumes no operating current Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared 2003 Microchip Technology Inc. Preliminary x = Bit is unknown DS41206A-page 49 PIC16F716 REGISTER 8-2: ADCON1 REGISTER (ADDRESS: 9Fh) U-0 U-0 U-0 U-0 U-0 R/W-0 R/W-0 R/W-0 — — — — — PCFG2 PCFG1 PCFG0 bit 7 bit 0 bit 7-3 Unimplemented: Read as '0' bit 2-0 PCFG2:PCFG0: A/D Port Configuration Control bits AN3 RA3 AN2 RA2 AN2 RA1 AN0 RA0 0x0 A A A A VDD 0x1 VREF A A A RA3 PCFG2:PCFG0 VREF 100 A D A A VDD 101 VREF D A A RA3 D D D D VDD 11x Legend: A = Analog input, D = Digital I/O Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = Bit is set ‘0’ = Bit is cleared The ADRES register contains the result of the A/D conversion. When the A/D conversion is complete, the result is loaded into the ADRES register, the GO/DONE bit (ADCON0<2>) is cleared and the A/D interrupt flag bit ADIF is set. The block diagram of the A/D module is shown in Figure 8-1. The value that is in the ADRES register is not modified for any Reset. The ADRES register will contain unknown data after a Power-on Reset. After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine acquisition time, see Section 8.1 “A/D Acquisition Requirements”. After this acquisition time has elapsed, the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 1. 2. 3. 4. 5. Configure the A/D module: - Configure analog pins/voltage reference/ and digital I/O (ADCON1) - Select A/D input channel (ADCON0) - Select A/D conversion clock (ADCON0) - Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): - Clear ADIF bit - Set ADIE bit - Set GIE bit Wait the required acquisition time. Start conversion: - Set GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: - Polling for the GO/DONE bit to be cleared OR 6. 7. DS41206A-page 50 x = Bit is unknown Preliminary - Waiting for the A/D interrupt Read A/D Result register (ADRES), clear bit ADIF if required. For the next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2TAD is required before next acquisition starts. 2003 Microchip Technology Inc. PIC16F716 FIGURE 8-1: A/D BLOCK DIAGRAM CHS2:CHS0 VIN 011 (Input voltage) RA3/AN3/VREF 010 RA2/AN2 A/D Converter 001 RA1/AN1 000 VDD RA0/AN0 000 or 010 or 100 or 110 or 111 VREF (Reference voltage) 001 or 011 or 101 PCFG2:PCFG0 8.1 A/D Acquisition Requirements For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 8-2. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD). The source impedance affects the offset voltage at the analog input (due to pin leakage current). The maximum recommended impedance for analog sources is 10 kΩ. After the analog input channel is selected (changed) this acquisition must be done before the conversion can be started. FIGURE 8-2: To calculate the minimum acquisition time, TACQ, see the PICmicro® Mid-Range Reference Manual, (DS33023). This equation calculates the acquisition time to within 1/2 LSb error. The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified accuracy. Note: When the conversion is started, the holding capacitor is disconnected from the input pin. ANALOG INPUT MODEL VDD Rs ANx CPIN 5 pF VA Sampling Switch VT = 0.6V VT = 0.6V RIC ≤ 1k SS RSS CHOLD = DAC capacitance = 51.2 pF I leakage ± 500 nA VSS Legend: CPIN = input capacitance VT = threshold voltage I leakage = leakage current at the pin due to various junctions RIC SS CHOLD 2003 Microchip Technology Inc. = interconnect resistance = sampling switch = sample/hold capacitance (from DAC) Preliminary VDD 6V 5V 4V 3V 2V 5 6 7 8 9 10 11 Sampling Switch (kΩ) DS41206A-page 51 PIC16F716 8.2 Selecting the A/D Conversion Clock 8.3 The A/D conversion time per bit is defined as TAD. The A/D conversion requires 9.5 TAD per 8-bit conversion. The source of the A/D conversion clock is software selectable. The four possible options for TAD are: • • • • 2 TOSC 8 TOSC 32 TOSC Internal RC oscillator The ADCON1 and TRISA registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of 1.6 µs. Table 8-1 shows the resultant TAD times derived from the device operating frequencies and the A/D clock source selected. TABLE 8-1: Note 1: When reading the port register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs, will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. 2: Analog levels on any pin that is defined as a digital input (including the AN3:AN0 pins), may cause the input buffer to consume current that is out of the devices specification. TAD vs. DEVICE OPERATING FREQUENCIES AD Clock Source (TAD) Operation 2 TOSC 8 TOSC 32 TOSC RC Legend: Note 1: 2: 3: 4: Configuring Analog Port Pins Device Frequency ADCS1:ADCS0 20 MHz 5 MHz 1.25 MHz 333.33 kHz 00 100 ns(2) 400 ns(2) 1.6 µs 6 µs 01 ns(2) 1.6 µs 6.4 µs 24 µs(3) 10 400 1.6 µs 6.4 µs 25.6 µs(3) 96 µs(3) 11 2-6 µs(1), (4) 2-6 µs(1), (4) 2-6 µs(1), (4) 2-6 µs(1) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 4 µs. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. When device frequency is greater than 1 MHz, the RC A/D conversion clock source is recommended for Sleep operation only. DS41206A-page 52 Preliminary 2003 Microchip Technology Inc. PIC16F716 8.4 Note: 8.5 A/D Conversions The GO/DONE bit should NOT be set in the same instruction that turns on the A/D. Use of the ECCP Trigger An A/D conversion can be started by the “special event trigger” of the ECCP module. This requires that the CCP1M3:CCP1M0 bits (CCP1CON<3:0>) be programmed as ‘1011’ and that the A/D module is enabled (ADON bit is set). When the trigger occurs, the GO/DONE bit will be set, starting the A/D conversion, and the Timer1 counter will be reset to zero. Timer1 is reset to automatically repeat the A/D acquisition period with minimal software overhead (moving the ADRES to the desired location). The appropriate analog input channel must be selected and the minimum acquisition done before the “special event trigger” sets the GO/ DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), then the “special event trigger” will be ignored by the A/D module, but will still reset the Timer1 counter. TABLE 8-2: Address Name SUMMARY OF A/D REGISTERS Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR Value on all other Resets 05h PORTA — — —(1) RA4 RA3 RA2 RA1 RA0 --xx 0000 --uu uuuu 0Bh,8Bh INTCON GIE PEIE T0IE INTE RBIE T0IF INTF RBIF 0000 000x 0000 000u 0Ch PIR1 — ADIF — — — CCP1IF TMR2IF TMR1IF -0-- -000 -0-- -000 1Eh ADRES A/D Result Register xxxx xxxx uuuu uuuu 1Fh ADCON0 ADCS1 0000 0000 0000 0000 --11 1111 --11 1111 ADCS0 CHS2 CHS1 (1) CHS0 GO/DONE —(1) ADON 85h TRISA — — 8Ch PIE1 — ADIE — — — CCP1IE TMR2IE TMR1IE -0-- -000 -0-- 0000 9Fh ADCON1 — — — — — PCFG2 PCFG1 PCFG0 ---- -000 ---- -000 Legend: Note 1: — PORTA Data Direction Register x = unknown, u = unchanged, - = unimplemented read as ‘0’. Shaded cells are not used for A/D conversion. Reserved bit, do not use. 2003 Microchip Technology Inc. Preliminary DS41206A-page 53 PIC16F716 NOTES: DS41206A-page 54 Preliminary 2003 Microchip Technology Inc. PIC16F716 9.0 SPECIAL FEATURES OF THE CPU The PIC16F716 device has a host of features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These are: • OSC Selection • Reset - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) • Interrupts • Watchdog Timer (WDT) • Sleep • Code protection • ID locations • In-Circuit Serial Programming™ (ICSP™) 9.1 Configuration Bits The configuration bits can be programmed (read as ‘0’) or left unprogrammed (read as ‘1’) to select various device configurations. These bits are mapped in program memory location 2007h. The user will note that address 2007h is beyond the user program memory space. In fact, it belongs to the special configuration memory space (2000h – 3FFFh), which can be accessed only during programming. The PIC16F716 device has a Watchdog Timer, which can be shut off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in Reset until the crystal oscillator is stable. The other is the Power-up Timer (PWRT), which provides a fixed delay on power-up only and is designed to keep the part in Reset while the power supply stabilizes. With these two timers on-chip, most applications need no external Reset circuitry. Sleep mode is designed to offer a very low current Power-down mode. The user can wake-up from Sleep through external Reset, Watchdog Timer Wake-up, or through an interrupt. Several oscillator options are also made available to allow the part to fit the application. The RC oscillator option saves system cost, while the LP crystal option saves power. A set of configuration bits are used to select various options. Additional information on special features is available in the PICmicro® Mid-Range Reference Manual, (DS33023). 2003 Microchip Technology Inc. Preliminary DS41206A-page 55 PIC16F716 REGISTER 9-1: CP — CONFIGURATION WORD — — — — BORV BOREN — — PWRTE WDTE FOSC1 FOSC0 bit 13 bit 0 bit 13 CP: Flash Program Memory Code Protection bit 1 = Code protection off 0 = All program memory code protected bit 12-8 Unimplemented: Read as ‘1’ bit 7 BORV: Brown-out Reset Voltage bit 1 = VBOR set to 4.0V 0 = VBOR set to 2.5V bit 6 BOREN: Brown-out Reset Enable bit(1) 1 = BOR enabled 0 = BOR disabled bit 5-4 Unimplemented: Read as ‘1’ bit 3 PWRTE: Power-up Timer Enable bit (1) 1 = PWRT disabled 0 = PWRT enabled bit 2 WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled bit 1-0 FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator Note 1: Enabling Brown-out Reset does not automatically enable Power-up Timer (PWRTE). Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’ -n = Value at POR ‘1’ = bit is set ‘0’ = bit is cleared DS41206A-page 56 Preliminary x = bit is unknown 2003 Microchip Technology Inc. PIC16F716 9.2 TABLE 9-1: Oscillator Configurations 9.2.1 Ranges Tested: OSCILLATOR TYPES The PIC16F716 can be operated in four different oscillator modes. The user can program two configuration bits (FOSC1 and FOSC0) to select one of these four modes: • • • • LP - Low-power Crystal XT - Crystal/Resonator HS - High-speed Crystal/Resonator RC - Resistor/Capacitor 9.2.2 In XT, LP or HS modes, a crystal or ceramic resonator is connected to the OSC1/CLKIN and OSC2/CLKOUT pins to establish oscillation (Figure 9-1). The PIC16F716 oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP or HS modes, the device can have an external clock source to drive the OSC1/CLKIN pin (Figure 9-2). CRYSTAL/CERAMIC RESONATOR OPERATION (HS, XT OR LP OSC CONFIGURATION) C1(1) OSC1 XTAL RF(3) Sleep OSC2 RS(2) C2(1) Note 1: 2: 3: Mode XT HS Note 1: CRYSTAL OSCILLATOR/CERAMIC RESONATORS FIGURE 9-1: To internal logic Freq Osc Type LP XT HS Note 1: OSC1 (C1) OSC2 (C2) 455 kHz 68-100 pF 68-100 pF 2.0 MHz 15-68 pF 15-68 pF 4.0 MHz 10-68 pF 10-68 pF 8.0 MHz 15-68 pF 15-68 pF 16.0 MHz 10-22 pF 10-22 pF These values are for design guidance only. See notes at bottom of page. TABLE 9-2: CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR Crystal Freq Cap. Range C1 Cap. Range C2 15-33 pF 32 kHz 15-33 pF 200 kHz 5-10 pF 5-10 pF 200 kHz 47-68 pF 47-68 pF 1 MHz 15-33 pF 15-33 pF 15-33 pF 4 MHz 15-33 pF 4 MHz 15-33 pF 15-33 pF 8 MHz 15-33 pF 15-33 pF 20 MHz 15-33 pF 15-33 pF These values are for design guidance only. See notes at bottom of page. Note 1: Higher capacitance increases the stability of the oscillator, but also increases the start-up time. PIC16F716 See Table 9-1 and Table 9-2 for recommended values of C1 and C2. A series resistor (RS) may be required. RF varies with the crystal chosen. FIGURE 9-2: CERAMIC RESONATORS 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 3: RS may be required to avoid overdriving crystals with low drive level specification. 4: When using an external clock for the OSC1 input, loading of the OSC2 pin must be kept to a minimum by leaving the OSC2 pin unconnected. EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION) OSC1 Clock from ext. system PIC16F716 Open OSC2 2003 Microchip Technology Inc. Preliminary DS41206A-page 57 PIC16F716 9.2.3 RC OSCILLATOR For timing insensitive applications, the “RC” device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values and the operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external R and C components used. Figure 9-3 shows how the R/C combination is connected to the PIC16F716. FIGURE 9-3: RC OSCILLATOR MODE VDD CEXT Internal clock PIC16F716 VSS FOSC/4 The PICmicro® microcontrollers have an MCLR noise filter in the MCLR Reset path. The filter will detect and ignore small pulses. It should be noted that a WDT Reset does not drive the MCLR pin low. 9.4 Power-On Reset (POR) A Power-on Reset pulse is generated on-chip when VDD rise is detected. To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD. This will eliminate external RC components usually needed to create a Power-on Reset. A maximum rise time for VDD is specified (parameter D004). For a slow rise time, see Figure 9-4. When the device starts normal operation (exits the Reset condition), device operating parameters (voltage, frequency, temperature,...) must be met to ensure operation. If these conditions are not met, the device must be held in Reset until the operating conditions are met. Brown-out Reset may be used to meet the start-up conditions. REXT OSC1 A simplified block diagram of the On-chip Reset circuit is shown in Figure 9-5. OSC2/CLKOUT FIGURE 9-4: EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP) Recommended values: 3 kΩ ≤ REXT ≤ 100 kΩ (VDD ≥ 3.0V) 10 kΩ ≤ REXT ≤ 100 kΩ (VDD ≥ 3.0V) CEXT > 20 pF 9.3 VDD VDD R Reset R1 MCLR The PIC16F716 differentiates between various kinds of Reset: • • • • • • Power-on Reset (POR) MCLR Reset during normal operation MCLR Reset during Sleep WDT Reset (during normal operation) WDT Wake-up (during Sleep) Brown-out Reset (BOR) C Note 1: 2: Some registers are not affected in any Reset condition; their status is unknown on POR and unchanged in any other Reset. Most other registers are reset to a “Reset state” on Power-on Reset (POR), on the MCLR and WDT Reset, on MCLR Reset during Sleep and Brownout Reset (BOR). They are not affected by a WDT Wake-up, which is viewed as the resumption of normal operation. The TO and PD bits are set or cleared differently in different Reset situations as indicated in Table 9-4. These bits are used in software to determine the nature of the Reset. See Table 9-6 for a full description of Reset states of all registers. DS41206A-page 58 Preliminary 3: PIC16F716 External Power-on Reset circuit is required only if VDD power-up slope is too slow. The diode D helps discharge the capacitor quickly when VDD powers down. R < 40 kΩ is recommended to make sure that voltage drop across R does not violate the device’s electrical specification. R1 = 100Ω to 1 kΩ will limit any current flowing into MCLR from external capacitor C in the event of MCLR/VPP pin breakdown due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS). 2003 Microchip Technology Inc. PIC16F716 9.5 Power-up Timer (PWRT) 9.7 The Power-up Timer provides a fixed nominal time-out, on power-up only, from the POR. The Power-up Timer operates on an internal RC oscillator. The chip is kept in Reset as long as the PWRT is active. The PWRT’s time delay allows VDD to rise to an acceptable level. The power-up timer enable configuration bit, PWRTE, is provided to enable/disable the PWRT. The power-up time delay will vary from chip-to-chip due to VDD, temperature and process variation. See AC parameters for details. 9.6 Oscillator Start-up Timer (OST) The Oscillator Start-up Timer (OST) provides a 1024 oscillator cycle (from OSC1 input) delay after the PWRT delay is over. This ensures that the crystal oscillator or resonator has started and stabilized. See AC parameters for details. The OST time-out is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from Sleep. Programmable Brown-Out Reset (PBOR) The PIC16F716 has on-chip Brown-out Reset circuitry. A configuration bit, BOREN, can disable (if clear/programmed) or enable (if set) the Brown-out Reset circuitry. The BORV configuration bit selects the programmable Brown-out Reset threshold voltage (VBOR). When BORV is 1, VBOR IS 4.0V. When BORV is 0, VBOR is 2.5V A Brown-out Reset occurs when VDD falls below VBOR for a time greater than parameter TBOR (see Table 12-4). A Brown-out Reset is not guaranteed to occur if VDD falls below VBOR for less than parameter TBOR. On any Reset (Power-on, Brown-out, Watchdog, etc.) the chip will remain in Reset until VDD rises above VBOR. The Power-up Timer will be invoked and will keep the chip in Reset an additional 72 ms only if the Power-up Timer enable bit in the configuration register is set to 0 (PWRTE = 0). If the Power-up Timer is enabled and VDD drops below VBOR while the Power-up Timer is running, the chip will go back into a Brown-out Reset and the Power-up Timer will be re-initialized. Once VDD rises above VBOR, the Power-up Timer will execute a 72 ms Reset. See Figure 9-6. For operations where the desired brown-out voltage is other than 4.0V or 2.5V, an external brown-out circuit must be used. Figure 9-8, Figure 9-9 and Figure 9-10 show examples of external Brown-out Protection circuits. 2003 Microchip Technology Inc. Preliminary DS41206A-page 59 PIC16F716 FIGURE 9-5: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT External Reset MCLR WDT Module Sleep WDT Time-out Reset VDD rise detect Power-on Reset VDD Brown-out Reset S BOREN OST/PWRT OST Chip_Reset R 10-bit Ripple counter Q OSC1 (1) On-chip RC OSC PWRT 10-bit Ripple counter PWRTE See Table 9-3 for time-out situations. Enable OST Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin. BROWN-OUT SITUATIONS (PWRTE = 0 FIGURE 9-6: VDD Internal Reset VBOR 72 ms VDD Internal Reset VBOR <72 ms 72 ms VDD Internal Reset DS41206A-page 60 VBOR 72 ms Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 9-7: EXTERNAL BROWN-OUT PROTECTION CIRCUIT 1 VDD FIGURE 9-9: VDD VDD 33k MCP809 Q1 10k EXTERNAL BROWN-OUT PROTECTION CIRCUIT 3 Vss MCLR bypass capacitor VDD VDD 40k RST PIC16F716 MCLR PIC16F716 Note 1: This circuit will activate Reset when VDD goes below (Vz + 0.7V) where Vz = Zener voltage. 2: Internal Brown-out Reset circuitry should be disabled when using this circuit. FIGURE 9-8: Note 1: EXTERNAL BROWN-OUT PROTECTION CIRCUIT 2 VDD This brown-out protection circuit employs Microchip Technology’s MCP809 microcontroller supervisor. The MCP8XX and MCP1XX families of supervisors provide push-pull and open collector outputs with both high and low active Reset pins. There are 7 different trip point selections to accommodate 5V and 3V systems. VDD R1 Q1 MCLR R2 40k PIC16F716 Note 1: This brown-out circuit is less expensive, albeit less accurate. Transistor Q1 turns off when VDD is below a certain level such that: R1 VDD x = 0.7 V R1 + R2 2: Internal Brown-out Reset should be disabled when using this circuit. 3: Resistors should be adjusted for the characteristics of the transistor. 2003 Microchip Technology Inc. Preliminary DS41206A-page 61 PIC16F716 9.8 Time-out Sequence 9.9 On power-up, the time-out sequence is as follows: First PWRT time-out is invoked after the POR time delay has expired. Then OST is activated. The total time-out will vary based on oscillator configuration and the status of the PWRT. For example, in RC mode with the PWRT disabled, there will be no time-out at all. Figure 9-10, Figure 9-11, and Figure 9-12 depict time-out sequences on power-up. Since the time-outs occur from the POR pulse, if MCLR is kept low long enough, the time-outs will expire. Then bringing MCLR high will begin execution immediately (Figure 9-12). This is useful for testing purposes or to synchronize more than one PIC16F716 device operating in parallel. Table 9-5 shows the Reset conditions for some special function registers, while Table 9-6 shows the Reset conditions for all the registers. TABLE 9-3: Power Control/Status Register (PCON) The Power Control/Status Register, PCON has two bits. Bit 0 is the Brown-out Reset Status bit, BOR. If the BOREN configuration bit is set, BOR is ‘1’ on Power-on Reset and reset to ‘0’ when a Brown-out condition occurs. BOR must then be set by the user and checked on subsequent resets to see if it is clear, indicating that another Brown-out has occurred. If the BOREN configuration bit is clear, BOR is unknown on Power-on Reset. Bit 1 is POR (Power-on Reset Status bit). It is cleared on a Power-on Reset and unaffected otherwise. The user must set this bit following a Power-on Reset. TIME-OUT IN VARIOUS SITUATIONS Power-up or Brown-out Oscillator Configuration XT, HS, LP Wake-up from Sleep PWRTE = 0 PWRTE = 1 72 ms + 1024 TOSC 1024 TOSC 1024 TOSC 72 ms — — RC TABLE 9-4: STATUS BITS AND THEIR SIGNIFICANCE POR BOR TO PD 0 x 1 1 Power-on Reset (BOREN = 0) 0 1 1 1 Power-on Reset (BOREN = 1) 0 x 0 x Illegal, TO is set on POR 0 x x 0 Illegal, PD is set on POR 1 0 1 1 Brown-out Reset 1 1 0 1 WDT Reset 1 1 0 0 WDT Wake-up 1 1 u u MCLR Reset during normal operation 1 1 1 0 MCLR Reset during Sleep or interrupt wake-up from Sleep DS41206A-page 62 Preliminary 2003 Microchip Technology Inc. PIC16F716 TABLE 9-5: RESET CONDITION FOR SPECIAL REGISTERS Program Counter Status Register PCON Register Power-on Reset (BOREN = 0) 000h 0001 1xxx ---- --0x Power-on Reset (BOREN = 1) 000h 0001 1xxx ---- --01 MCLR Reset during normal operation 000h 000u uuuu ---- --uu MCLR Reset during Sleep 000h 0001 0uuu ---- --uu WDT Reset 000h 0000 1uuu ---- --uu PC + 1 uuu0 0uuu ---- --uu Condition WDT Wake-up Brown-out Reset Interrupt wake-up from Sleep 000h 0001 1uuu ---- --u0 PC + 1(1) uuu1 0uuu ---- --uu Legend: u = unchanged, x = unknown, - = unimplemented bit read as ‘0’. Note 1: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 2003 Microchip Technology Inc. Preliminary DS41206A-page 63 PIC16F716 TABLE 9-6: Register W INITIALIZATION CONDITIONS FOR ALL REGISTERS OF THE PIC16F716 Power-on Reset, Brown-out Reset MCLR Resets WDT Reset Wake-up via WDT or Interrupt xxxx xxxx uuuu uuuu uuuu uuuu INDF N/A N/A N/A TMR0 xxxx xxxx uuuu uuuu uuuu uuuu 0000h 0000h PC + 1(2) PCL STATUS 0001 1xxx 000q quuu (3) uuuq quuu(3) FSR xxxx xxxx uuuu uuuu uuuu uuuu PORTA(4), (5), (6) --xx 0000 --xx 0000 --uu uuuu PORTB(4), (5) xxxx xxxx uuuu uuuu uuuu uuuu PCLATH ---0 0000 ---0 0000 ---u uuuu INTCON 0000 -00x 0000 -00u uuuu -uuu(1) PIR1 -0-- -000 -0-- -000 -u-- -uuu(1) TMR1L xxxx xxxx uuuu uuuu uuuu uuuu TMR1H xxxx xxxx uuuu uuuu uuuu uuuu T1CON --00 0000 --uu uuuu --uu uuuu TMR2 0000 0000 0000 0000 uuuu uuuu T2CON -000 0000 -000 0000 -uuu uuuu CCPR1L xxxx xxxx uuuu uuuu uuuu uuuu CCPR1H xxxx xxxx uuuu uuuu uuuu uuuu CCP1CON 0000 0000 0000 0000 uuuu uuuu PWM1CON 0000 0000 0000 0000 uuuu uuuu ECCPAS 00-0 0000 00-0 0000 u-uu uuuu ADRES xxxx xxxx uuuu uuuu uuuu uuuu ADCON0 0000 0000 0000 0000 uuuu uuuu OPTION_REG 1111 1111 1111 1111 uuuu uuuu TRISA --11 1111 --11 1111 --uu uuuu TRISB 1111 1111 1111 1111 uuuu uuuu PIE1 -0-- -000 -0-- -000 -u-- -uuu PCON ---- --qq ---- --uu ---- --uu PR2 1111 1111 1111 1111 uuuu uuuu ADCON1 ---- -000 ---- -000 ---- -uuu Legend: u = unchanged, x = unknown, - = unimplemented bit, read as ‘0’, q = value depends on condition Note 1: One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up). 2: When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). 3: See Table 9-5 for Reset value for specific condition. 4: On any device Reset, these pins are configured as inputs. 5: This is the value that will be in the port output latch. 6: Output latches are unknown or unchanged. Analog inputs default to analog and read ‘0’. DS41206A-page 64 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 9-10: TIME-OUT SEQUENCE ON POWER-UP (MCLR TIED TO VDD) VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 9-11: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 1 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET FIGURE 9-12: TIME-OUT SEQUENCE ON POWER-UP (MCLR NOT TIED TO VDD): CASE 2 VDD MCLR INTERNAL POR TPWRT PWRT TIME-OUT TOST OST TIME-OUT INTERNAL RESET 2003 Microchip Technology Inc. Preliminary DS41206A-page 65 PIC16F716 9.10 Interrupts The peripheral interrupt flags are contained in the special function registers, PIR1 and PIR2. The corresponding interrupt enable bits are contained in special function registers, PIE1 and PIE2, and the peripheral interrupt enable bit is contained in special function register, INTCON. The PIC16F716 devices have up to 7 sources of interrupt. The Interrupt Control Register (INTCON) records individual interrupt requests in flag bits. It also has individual and global interrupt enable bits. Note: Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupt, the return address is pushed onto the stack and the PC is loaded with 0004h. Once in the interrupt service routine, the source(s) of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bit(s) must be cleared in software before re-enabling interrupts to avoid recursive interrupts. A Global Interrupt Enable bit, GIE (INTCON<7>) enables all un-masked interrupts when set, or disables all interrupts when cleared. When bit GIE is enabled, and an interrupt’s flag bit and mask bit are set, the interrupt will vector immediately. Individual interrupts can be disabled through their corresponding enable bits in various registers. Individual interrupt bits are set, regardless of the status of the GIE bit. The GIE bit is cleared on Reset and when an interrupt vector occurs. For external interrupt events, such as the INT pin or PORTB change interrupt, the interrupt latency will be three or four instruction cycles. The exact latency depends when the interrupt event occurs. The latency is the same for one or two-cycle instructions. Individual interrupt flag bits are set, regardless of the status of their corresponding mask bit or the GIE bit. The “return-from-interrupt” instruction, RETFIE, exits the interrupt routine, as well as sets the GIE bit, which re-enables interrupts. The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in the INTCON register. FIGURE 9-13: INTERRUPT LOGIC T0IF T0IE INTF INTE ADIF ADIE Wake-up (If in Sleep mode) Interrupt to CPU RBIF RBIE PEIE CCP1IF CCP1IE GIE TMR2IF TMR2IE TMR1IF TMR1IE DS41206A-page 66 Preliminary 2003 Microchip Technology Inc. PIC16F716 9.10.1 INT INTERRUPT 9.11 External interrupt on RB0/INT pin is edge triggered, either rising if bit INTEDG (OPTION_REG<6>) is set, or falling if the INTEDG bit is clear. When a valid edge appears on the RB0/INT pin, flag bit INTF (INTCON<1>) is set. This interrupt can be disabled by clearing enable bit INTE (INTCON<4>). Flag bit INTF must be cleared in software in the interrupt service routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from Sleep, if bit INTE was set prior to going into Sleep. The status of global interrupt enable bit GIE decides whether or not the processor branches to the interrupt vector following wake-up. See Section 9.13 “Power-down Mode (Sleep)” for details on Sleep mode. 9.10.2 TMR0 INTERRUPT An overflow (FFh → 00h) in the TMR0 register will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>). (Section 4.0 “Timer0 Module”). 9.10.3 Context Saving During Interrupts During an interrupt, only the return PC value is saved on the stack. Typically, users may wish to save key registers during an interrupt, (i.e., W register and Status register). This will have to be implemented in firmware. Example 9-1 stores and restores the W, Status, PCLATH and FSR registers. Context storage registers, W_TEMP, STATUS_TEMP, PCLATH_TEMP and FSR_TEMP, must be defined in Common RAM which are those addresses between 70h-7Fh in Bank 0 and between F0h-FFh in Bank 1. The example: a) b) c) d) e) f) Stores the W register. Stores the Status register in Bank 0. Stores the PCLATH register Stores the FSR register. Executes the interrupt service routine code (User-generated). Restores all saved registers in reverse order from which they were stored PORTB INTCON CHANGE An input change on PORTB<7:4> sets flag bit RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit RBIE (INTCON<4>). (Section 3.2 “PORTB and the TRISB Register”). EXAMPLE 9-1: MOVWF SWAPF MOVWF MOVF MOVWF CLRF BCF MOVF MOVWF : :(ISR) : MOVF MOVWF MOVF MOVWF SWAPF MOVWF SWAPF SWAPF RETFIE SAVING STATUS, W, AND PCLATH REGISTERS IN RAM W_TEMP STATUS,W STATUS_TEMP PCLATH, W PCLATH_TEMP PCLATH STATUS, IRP FSR, W FSR_TEMP ;Copy W to TEMP register, could be bank one or zero ;Swap status to be saved into W ;Save status to bank zero STATUS_TEMP register ;Only required if using pages 1, 2 and/or 3 ;Save PCLATH into W ;Page zero, regardless of current page ;Return to Bank 0 ;Copy FSR to W ;Copy FSR from W to FSR_TEMP FSR_TEMP,W FSR PCLATH_TEMP, W PCLATH STATUS_TEMP,W STATUS W_TEMP,F W_TEMP,W ;Restore FSR ;Move W into FSR ;Restore PCLATH ;Move W into PCLATH ;Swap STATUS_TEMP register into W ;Move W into STATUS register ;Swap W_TEMP ;Swap W_TEMP into W ;Return from interrupt and enable GIE 2003 Microchip Technology Inc. Preliminary DS41206A-page 67 PIC16F716 9.12 Watchdog Timer (WDT) The Watchdog Timer is a free running, on-chip, RC oscillator which does not require any external components. This RC oscillator is separate from the RC oscillator of the OSC1/CLKIN pin. That means that the WDT will run, even if the clock on the OSC1/CLKIN and OSC2/CLKOUT pins of the device have been stopped, for example, by execution of a SLEEP instruction. During normal operation, a WDT time-out generates a device Reset (Watchdog Timer Reset). If the device is in Sleep mode, a WDT time-out causes the device to wake-up and continue with normal operation (Watchdog Timer Wake-up). The TO bit in the Status register will be cleared upon a Watchdog Timer time-out. FIGURE 9-14: The WDT can be permanently disabled by clearing configuration bit WDTE (Section 9.1 “Configuration Bits”). WDT time-out period values may be found in the Electrical Specifications section under TWDT (parameter #31). Values for the WDT prescaler (actually a postscaler, but shared with the Timer0 prescaler) may be assigned using the OPTION_REG register. Note: The CLRWDT and SLEEP instructions clear the WDT and the postscaler, if assigned to the WDT, and prevent it from timing out and generating a device Reset condition. Note: When a CLRWDT instruction is executed and the prescaler is assigned to the WDT, the prescaler count will be cleared, but the prescaler assignment is not changed. . WATCHDOG TIMER BLOCK DIAGRAM From TMR0 Clock Source (Figure 4-2) 0 1 WDT Timer Postscaler M U X 8 8 - to - 1 MUX PS2:PS0 PSA WDT Enable Bit To TMR0 (Figure 4-2) 0 1 MUX PSA WDT Time-out Note: PSA and PS2:PS0 are bits in the OPTION_REG register. FIGURE 9-15: Address SUMMARY OF WATCHDOG TIMER REGISTERS Name Bits 13:8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 2007h Config. bits (1) BORV(1) BOREN(1) — — PWRTE(1) WDTE FOSC1 FOSC0 81h OPTION_REG N/A RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 Legend: Note 1: Shaded cells are not used by the Watchdog Timer. See Register 9-1 for operation of these bits. DS41206A-page 68 Preliminary 2003 Microchip Technology Inc. PIC16F716 9.13 Power-down Mode (Sleep) Power-down mode is entered by executing a SLEEP instruction. If enabled, the Watchdog Timer will be cleared but keeps running, the PD bit (STATUS<3>) is cleared, the TO (STATUS<4>) bit is set, and the oscillator driver is turned off. The I/O ports maintain the status they had, before the SLEEP instruction was executed (driving high, low or high-impedance). The following peripheral interrupts can wake the device from Sleep: 1. 2. 3. TMR1 interrupt. Timer1 must be operating as an asynchronous counter. ECCP capture mode interrupt. ADC running in ADRC mode. Other peripherals cannot generate interrupts, since during Sleep, no on-chip clocks are present. The MCLR pin must be at a logic high level (parameter D042). When the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device continues execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, the user should have a NOP after the SLEEP instruction. 9.13.1 9.13.2 For lowest current consumption in this mode, place all I/O pins at either VDD or VSS, ensure no external circuitry is drawing current from the I/O pin, powerdown the A/D and the disable external clocks. Pull all I/O pins that are hi-impedance inputs, high or low externally, to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should be considered. WAKE-UP FROM SLEEP The device can wake-up from Sleep through one of the following events: 1. 2. 3. External Reset input on MCLR pin. Watchdog Timer Wake-up (if WDT was enabled). Interrupt from INT pin, RB port change or some peripheral interrupts. External MCLR Reset will cause a device Reset. All other events are considered a continuation of program execution and cause a “wake-up”. The TO and PD bits in the Status register can be used to determine the cause of device Reset. The PD bit, which is set on power-up, is cleared when Sleep is invoked. The TO bit is cleared if a WDT time-out occurred (and caused wake-up). WAKE-UP USING INTERRUPTS When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: • If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bits will not be cleared. • If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake-up from Sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction. 2003 Microchip Technology Inc. Preliminary DS41206A-page 69 PIC16F716 FIGURE 9-16: WAKE-UP FROM SLEEP THROUGH INTERRUPT Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 OSC1 TOST(2) CLKOUT(4) INT pin INTF flag (INTCON<1>) Interrupt Latency (Note 3) GIE bit (INTCON<7>) Processor in Sleep INSTRUCTION FLOW PC PC Instruction fetched Inst(PC) = Sleep Instruction executed Inst(PC - 1) Note 9.14 1: 2: 3: 4: PC+1 PC+2 Inst(PC + 2) Sleep Inst(PC + 1) PC + 2 Dummy cycle 0004h 0005h Inst(0004h) Inst(0005h) Dummy cycle Inst(0004h) XT, HS or LP Oscillator mode assumed. TOST = 1024TOSC (drawing not to scale). This delay will not be there for RC Osc mode. GIE = ‘1’ assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = ‘0’, execution will continue in-line. CLKOUT is not available in these osc modes, but shown here for timing reference. Program Verification/Code Protection 9.16 If the code protection bit has not been programmed, the on-chip program memory can be read out for verification purposes. 9.15 PC+2 Inst(PC + 1) ID Locations Four memory locations (2000h - 2003h) are designated as ID locations where the user can store checksum or other code-identification numbers. These locations are not accessible during normal execution, but are readable and writable during program/verify. It is recommended that only the 4 Least Significant bits of the ID location are used. DS41206A-page 70 In-Circuit Serial Programming™ PIC16F716 microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data, and three other lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. For complete details on serial programming, please refer to the In-Circuit Serial Programming™ (ICSP™) Specification, (DS40245). Preliminary 2003 Microchip Technology Inc. PIC16F716 10.0 INSTRUCTION SET SUMMARY Each PIC16F716 instruction is a 14-bit word divided into an opcode which specifies the instruction type and one or more operands which further specify the operation of the instruction. The PIC16F716 instruction set summary in Table 10-2 lists byte-oriented, bitoriented, and literal and control operations. Table 10-1 shows the opcode field descriptions. For byte-oriented instructions, ‘f’ represents a file register designator and ‘d’ represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If ‘d’ is zero, the result is placed in the W register. If ‘d’ is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, ‘b’ represents a bit field designator which selects the number of the bit affected by the operation, while ‘f’ represents the number of the file in which the bit is located. For literal and control operations, ‘k’ represents an eight or eleven bit constant or literal value. TABLE 10-1: • Byte-oriented operations • Bit-oriented operations • Literal and control operations All instructions are executed within one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles with the second cycle executed as a NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction execution time is 1 µs. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 µs. Table 10-2 lists the instructions recognized by the MPASM™ assembler. Figure 10-1 shows the three general formats that the instructions can have. Note 1: Any unused opcode is reserved. Use of any reserved opcode may cause unexpected operation. OPCODE FIELD DESCRIPTIONS Field 2: To maintain upward compatibility with future PICmicro products, do not use the OPTION and TRIS instructions. Description All examples use the following format to represent a hexadecimal number: f Register file address (0x00 to 0x7F) W Working register (accumulator) b Bit address within an 8-bit file register k Literal field, constant data or label x Don't care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. d The instruction set is highly orthogonal and is grouped into three basic categories: 0xhh where h signifies a hexadecimal digit. FIGURE 10-1: Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1 label Label name TOS Top of Stack PC Program Counter GENERAL FORMAT FOR INSTRUCTIONS Byte-oriented file register operations 13 8 7 6 OPCODE d 0 f (FILE #) d = 0 for destination W d = 1 for destination f f = 7-bit file register address PCLATH Program Counter High Latch GIE Global Interrupt Enable bit WDT Watchdog Timer/Counter TO Time-out bit PD Power-down bit dest Destination either the W register or the specified register file location [ ] Options Bit-oriented file register operations 13 10 9 76 OPCODE b (BIT #) 0 f (FILE #) b = 3-bit address f = 7-bit file register address ( ) Contents Literal and control operations → Assigned to General <> Register bit field ∈ In the set of italics User defined term (font is courier) 13 8 7 OPCODE 0 k (literal) k = 8-bit immediate value CALL and GOTO instructions only 13 11 10 OPCODE 0 k (literal) k = 11-bit immediate value 2003 Microchip Technology Inc. Preliminary DS41206A-page 71 PIC16F716 TABLE 10-2: PIC16F716 INSTRUCTION SET 14-Bit Opcode Mnemonic, Operands Description Cycles MSb LSb Status Affected Notes BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f — f, d f, d f, d f, d f, d f, d f, d f — f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f 1 1 1 1 1 1 1(2) 1 1(2) 1 1 1 1 1 1 1 1 1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 dfff dfff lfff 0xxx dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff xxxx ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff 1 1 1(2) 1(2) 01 01 01 01 00bb 01bb 10bb 11bb bfff bfff bfff bfff ffff ffff ffff ffff 1 1 2 1 2 1 1 2 2 2 1 1 1 11 11 10 00 10 11 11 00 11 00 00 11 11 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk C,DC,Z Z Z Z Z Z Z Z Z C C C,DC,Z Z 1,2 1,2 2 1,2 1,2 1,2,3 1,2 1,2,3 1,2 1,2 1,2 1,2 1,2 1,2 1,2 BIT-ORIENTED FILE REGISTER OPERATIONS BCF BSF BTFSC BTFSS f, b f, b f, b f, b Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set 1,2 1,2 3 3 LITERAL AND CONTROL OPERATIONS ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW Note 1: 2: 3: k k k — k k k — k — — k k Add literal and W AND literal with W Call subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into Standby mode Subtract W from literal Exclusive OR literal with W C,DC,Z Z TO,PD Z TO,PD C,DC,Z Z When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is ‘1’ for a pin configured as input and is driven low by an external device, the data will be written back with a ‘0’. If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP. DS41206A-page 72 Preliminary 2003 Microchip Technology Inc. PIC16F716 10.1 Instruction Descriptions ADDLW Add Literal and W Syntax: [ label ] ADDLW Operands: ANDLW AND Literal with W Syntax: [ label ] ANDLW 0 ≤ k ≤ 255 Operands: 0 ≤ k ≤ 255 Operation: (W) + k → (W) Operation: (W) .AND. (k) → (W) Status Affected: C, DC, Z Status Affected: Z Encoding: 11 Encoding: 11 Description: The contents of the W register are added to the eight bit literal ‘k’ and the result is placed in the W register. Description: The contents of W register are AND’ed with the eight bit literal ‘k’. The result is placed in the W register. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Example ADDLW Example ANDLW 111x k kkkk kkkk 0x15 Before Instruction W = 0x10 After Instruction W = 0x25 ADDWF Add W and f Syntax: [ label ] ADDWF Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (W) + (f) → (dest) Status Affected: C, DC, Z 1001 k kkkk kkkk 0x5F Before Instruction W = 0xA3 After Instruction W = 0x03 f,d ANDWF AND W with f Syntax: [ label ] ANDWF Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (W) .AND. (f) → (dest) Status Affected: Z Encoding: 00 0101 f,d dfff ffff Encoding: 00 Description: Description: Add the contents of the W register with register ‘f’. If ‘d’ is 0 the result is stored in the W register. If ‘d’ is 1 the result is stored back in register ‘f’. AND the W register with register ‘f’. If ‘d’ is 0 the result is stored in the W register. If ‘d’ is 1 the result is stored back in register ‘f’. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Example ANDWF Example ADDWF 0111 dfff ffff REG1, 0 Before Instruction W = 0x17 REG1 = 0xC2 After Instruction W = 0x17 REG1 = 0x02 Before Instruction W = 0x17 REG1 = 0xC2 After Instruction W = 0xD9 REG1 = 0xC2 Z = 0 C = 0 DC = 0 2003 Microchip Technology Inc. REG1, 1 Preliminary DS41206A-page 73 PIC16F716 BCF Bit Clear f BTFSC Bit Test f, Skip if Clear Syntax: [ label ] BCF Syntax: [ label ] BTFSC f,b Operands: 0 ≤ f ≤ 127 0≤b≤7 Operands: 0 ≤ f ≤ 127 0≤b≤7 Operation: 0 → (f<b>) Operation: skip if (f<b>) = 0 Status Affected: None Status Affected: None Encoding: 01 Description: Bit ‘b’ in register ‘f’ is cleared. Words: 1 Cycles: 1 Example BCF f,b 00bb bfff ffff Encoding: BSF Bit Set f Syntax: [ label ] BSF Operands: 0 ≤ f ≤ 127 0≤b≤7 Operation: 1 → (f<b>) Status Affected: None Encoding: 01 Description: Bit ‘b’ in register ‘f’ is set. Words: 1 Cycles: 1 Example BSF 01bb bfff ffff If bit ‘b’ in register ‘f’ is ‘0’ then the next instruction is skipped. If bit ‘b’ is ‘0’ then the next instruction fetched during the current instruction execution is discarded, and a NOP is executed instead, making this a two-cycle instruction. Words: 1 Cycles: 1(2) Example HERE FALSE TRUE f,b bfff 10bb Description: REG1, 7 Before Instruction REG1 = 0xC7 After Instruction REG1 = 0x47 01 ffff BTFSC GOTO • • • REG1 PROCESS_CODE Before Instruction PC = address HERE After Instruction if REG<1> = 0, PC = address TRUE if REG<1>=1, PC = address FALSE REG1, 7 Before Instruction REG1 = 0x0A After Instruction REG1 = 0x8A DS41206A-page 74 Preliminary 2003 Microchip Technology Inc. PIC16F716 BTFSS Bit Test f, Skip if Set CALL Call Subroutine Syntax: [ label ] BTFSS f,b Syntax: [ label ] CALL k Operands: 0 ≤ f ≤ 127 0≤b<7 Operands: 0 ≤ k ≤ 2047 Operation: Operation: skip if (f<b>) = 1 Status Affected: None (PC)+ 1→ TOS, k → PC<10:0>, (PCLATH<4:3>) → PC<12:11> Encoding: 01 Status Affected: None Description: If bit ‘b’ in register ‘f’ is ‘1’ then the next instruction is skipped. If bit ‘b’ is ‘1’, then the next instruction fetched during the current instruction execution, is discarded and a NOP is executed instead, making this a two-cycle instruction. Encoding: 10 Description: Call Subroutine. First, return address (PC+1) is pushed onto the stack. The eleven bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a two-cycle instruction. Words: 1 Cycles: 2 Example HERE Words: 1 Cycles: 1(2) Example HERE FALSE TRUE 11bb BTFSS GOTO • • • bfff ffff REG1 PROCESS_CODE Before Instruction PC = address HERE After Instruction if FLAG<1> = 0, PC = address FALSE if FLAG<1> = 1, PC = address TRUE 0kkk CALL kkkk kkkk THERE Before Instruction PC = Address HERE After Instruction PC = Address THERE TOS = Address HERE+1 CLRF Syntax: Clear f [ label ] CLRF Operands: 0 ≤ f ≤ 127 Operation: 00h → (f) 1→Z f Status Affected: Z Encoding: 00 Description: The contents of register ‘f’ are cleared and the Z bit is set. Words: 1 Cycles: 1 Example CLRF 0001 1fff ffff REG1 Before Instruction REG1 = 0x5A After Instruction REG1 = 0x00 Z = 1 2003 Microchip Technology Inc. Preliminary DS41206A-page 75 PIC16F716 CLRW Clear W COMF Complement f Syntax: [ label ] CLRW Syntax: [ label ] COMF Operands: None Operands: Operation: 00h → (W) 1→Z 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (f) → (dest) Status Affected: Z Status Affected: Z Encoding: 00 Encoding: 00 Description: W register is cleared. Zero bit (Z) is set. Description: Words: 1 Cycles: 1 The contents of register ‘f’ are complemented. If ‘d’ is 0 the result is stored in W. If ‘d’ is 1 the result is stored back in register ‘f’. Example CLRW Words: 1 Before Instruction W = 0x5A After Instruction W = 0x00 Z = 1 Cycles: 1 Example COMF CLRWDT Clear Watchdog Timer DECF Syntax: [ label ] CLRWDT Operands: None Operands: Operation: 00h → WDT 0 → WDT prescaler, 1 → TO 1 → PD 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (f) - 1 → (dest) Status Affected: Z Status Affected: TO, PD Encoding: Encoding: 00 Description: 0001 0000 0011 1001 f,d dfff ffff REG1, 0 Before Instruction REG1 = 0x13 After Instruction REG1 = 0x13 W = 0xEC Syntax: Decrement f [ label ] DECF f,d 00 0011 dfff ffff Description: CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set. Decrement register ‘f’. If ‘d’ is 0 the result is stored in the W register. If ‘d’ is 1 the result is stored back in register ‘f’. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Example DECF Example 0000 0110 CLRWDT Before Instruction WDT counter = ? After Instruction WDT counter = WDT prescaler = = TO = PD DS41206A-page 76 0100 0x00 0 1 1 Preliminary CNT, 1 Before Instruction CNT = 0x01 Z = 0 After Instruction CNT = 0x00 Z = 1 2003 Microchip Technology Inc. PIC16F716 DECFSZ Decrement f, Skip if 0 GOTO Unconditional Branch Syntax: [ label ] DECFSZ f,d Syntax: [ label ] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operands: 0 ≤ k ≤ 2047 Operation: (f) - 1 → (dest); 0 Operation: k → PC<10:0> PCLATH<4:3> → PC<12:11> Status Affected: None Status Affected: None Encoding: Encoding: 10 00 Description: The contents of register ‘f’ are decremented. If ‘d’ is 0 the result is placed in the W register. If ‘d’ is 1 the result is placed back in register ‘f’. If the result is 0, the next instruction, which is already fetched, is discarded. A NOP is executed instead making it a two-cycle instruction. Description: GOTO is an unconditional branch. The eleven-bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a two-cycle instruction. Words: 1 Cycles: 2 Example GOTO THERE Words: 1 Cycles: 1(2) Example HERE 1011 DECFSZ GOTO CONTINUE • • • skip if result = dfff ffff GOTO k 1kkk kkkk kkkk After Instruction PC = Address THERE REG1, 1 LOOP Before Instruction PC = address HERE After Instruction REG1 = REG1 - 1 if REG1 = 0, PC = address CONTINUE if REG1 ≠ 0, PC = address HERE+1 2003 Microchip Technology Inc. Preliminary DS41206A-page 77 PIC16F716 INCF Increment f INCFSZ Increment f, Skip if 0 Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (f) + 1 → (dest) Operation: (f) + 1 → (dest), skip if result = 0 Status Affected: Z Status Affected: None Encoding: 00 Encoding: 00 Description: The contents of register ‘f’ are incremented. If ‘d’ is 0 the result is placed in the W register. If ‘d’ is 1 the result is placed back in register ‘f’. Description: Words: 1 Cycles: 1 Example INCF The contents of register ‘f’ are incremented. If ‘d’ is 0 the result is placed in the W register. If ‘d’ is 1 the result is placed back in register ‘f’. If the result is 0, the next instruction, which is already fetched, is discarded. A NOP is executed instead making it a two-cycle instruction. Words: 1 INCF f,d 1010 dfff ffff REG1, 1 Before Instruction REG1 = 0xFF Z = 0 After Instruction REG1 = 0x00 Z = 1 INCFSZ f,d 1111 Cycles: 1(2) Example HERE dfff INCFSZ GOTO CONTINUE • • • ffff REG1, 1 LOOP Before Instruction PC = address HERE After Instruction REG1 = REG1 + 1 if CNT = 0, PC = address CONTINUE if REG1≠ 0, PC = address HERE +1 DS41206A-page 78 Preliminary 2003 Microchip Technology Inc. PIC16F716 IORLW Inclusive OR Literal with W MOVLW Move Literal to W Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ k ≤ 255 Operands: 0 ≤ k ≤ 255 Operation: (W) .OR. k → (W) Operation: k → (W) Status Affected: Z Status Affected: None Encoding: 11 Encoding: 11 Description: The contents of the W register is OR’ed with the eight bit literal ‘k’. The result is placed in the W register. Description: The eight bit literal ‘k’ is loaded into W register. The don’t cares will assemble as ‘0’s. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Example MOVLW Example IORLW IORLW k 1000 kkkk kkkk 0x35 MOVLW k 00xx kkkk kkkk 0x5A After Instruction W = 0x5A Before Instruction W = 0x9A After Instruction W = 0xBF Z = 0 IORWF Inclusive OR W with f MOVF Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (f) → (dest) Status Affected: Z Encoding: 00 Description: The contents of register ‘f’ is moved to a destination dependent upon the status of ‘d’. If ‘d’ = 0, destination is W register. If ‘d’ = 1, the destination is file register ‘f’ itself. ‘d’ = 1 is useful to test a file register since status flag Z is affected. Words: 1 Cycles: 1 Example MOVF IORWF f,d Operation: (W) .OR. (f) → (dest) Status Affected: Z Encoding: 00 Description: Inclusive OR the W register with register ‘f’. If ‘d’ is 0 the result is placed in the W register. If ‘d’ is 1 the result is placed back in register ‘f’. Words: 1 Cycles: 1 Example IORWF 0100 dfff REG1, 0 Before Instruction REG1 = 0x13 W = 0x91 After Instruction REG1 = 0x13 W = 0x93 Z = 1 2003 Microchip Technology Inc. ffff Move f MOVF f,d 1000 dfff ffff REG1, 0 After Instruction W= value in REG1 register Z = 1 Preliminary DS41206A-page 79 PIC16F716 MOVWF Move W to f OPTION Load Option Register Syntax: [ label ] Syntax: [ label ] 0 ≤ f ≤ 127 Operands: None Operands: Operation: (W) → (f) Operation: (W) → OPTION Status Affected: None Status Affected: None Encoding: 00 Encoding: 00 Description: The contents of the W register are loaded in the OPTION register. This instruction is supported for code compatibility with PIC16C5X products. Since OPTION is a readable/writable register, the user can directly address it. Using only register instruction such as MOVWF. Words: 1 Cycles: 1 MOVWF 0000 f 1fff ffff Description: Move data from W register to register ‘f’. Words: 1 Cycles: 1 Example MOVWF REG1 Before Instruction REG1 = 0xFF W = 0x4F After Instruction REG1 = 0x4F W = 0x4F OPTION 0000 0110 0010 Example To maintain upward compatibility with future PICmicro® products, do not use this instruction. NOP No Operation RETFIE Return from Interrupt Syntax: [ label ] Syntax: [ label ] Operands: None Operands: None Operation: No operation Operation: Status Affected: None TOS → PC, 1 → GIE Encoding: 00 Status Affected: None Description: No operation. Encoding: 00 Words: 1 Description: Cycles: 1 Example NOP Return from Interrupt. Stack is POPed and Top of Stack (TOS) is loaded in the PC. Interrupts are enabled by setting Global Interrupt Enable bit, GIE (INTCON<7>). This is a two-cycle instruction. Words: 1 Cycles: 2 Example RETFIE NOP 0000 0xx0 0000 RETFIE 0000 0000 1001 After Interrupt PC = TOS GIE = 1 DS41206A-page 80 Preliminary 2003 Microchip Technology Inc. PIC16F716 RETLW Return with Literal in W RLF Rotate Left f through Carry Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ k ≤ 255 Operands: Operation: k → (W); TOS → PC 0 ≤ f ≤ 127 d ∈ [0,1] Operation: See description below Status Affected: None Status Affected: C Encoding: 11 Encoding: 00 Description: The W register is loaded with the eight bit literal ‘k’. The program counter is loaded from the top of the stack (the return address). This is a two-cycle instruction. Description: The contents of register ‘f’ are rotated one bit to the left through the Carry Flag. If ‘d’ is 0 the result is placed in the W register. If ‘d’ is 1 the result is stored back in register ‘f’. Words: 1 Cycles: 2 Example CALL TABLE;W contains table ;offset value • ;W now has table value • • ADDWF PC;W = offset RETLW k1;Begin table RETLW k2; • • • RETLW kn; End of table TABLE RETLW k 01xx kkkk kkkk 1 Cycles: 1 Example RLF f,d 1101 C Words: RLF dfff ffff REGISTER F REG1, 0 Before Instruction REG1=1110 0110 C = 0 After Instruction REG1=1110 0110 W = 1100 1100 C = 1 Before Instruction W = 0x07 After Instruction W = value of k8 RETURN Return from Subroutine Syntax: [ label ] Operands: None Operation: TOS → PC Status Affected: None Encoding: 00 Description: Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two-cycle instruction. Words: 1 Cycles: 2 Example RETURN RETURN 0000 0000 1000 After Interrupt PC = TOS 2003 Microchip Technology Inc. Preliminary DS41206A-page 81 PIC16F716 RRF Rotate Right f through Carry SUBLW Subtract W from Literal Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operands: 0 ≤ k ≤ 255 Operation: k - (W) → (W) Operation: See description below C, DC, Z Status Affected: C Status Affected: Encoding: 00 Encoding: 11 Description: The contents of register ‘f’ are rotated one bit to the right through the Carry Flag. If ‘d’ is 0 the result is placed in the W register. If ‘d’ is 1 the result is placed back in register ‘f’. Description: The W register is subtracted (2’s complement method) from the eight bit literal ‘k’. The result is placed in the W register. 1100 C Words: 1 Cycles: 1 Example RRF RRF f,d dfff ffff REGISTER F SUBLW k 110x Words: 1 Cycles: 1 Example 1: SUBLW kkkk kkkk 0x02 Before Instruction W = 1 C = ? REG1, 0 After Instruction Before Instruction REG1 = 1110 0110 C = 0 After Instruction REG1 = 1110 0110 W = 0111 0011 C = 0 W = 1 C = 1; result is positive Example 2: Before Instruction W = 2 C = ? After Instruction W = 0 C = 1; result is zero SLEEP Example 3: Syntax: [ label ] SLEEP Operands: None Operation: 00h → WDT, 0 → WDT prescaler, 1 → TO, 0 → PD W = C = W = C = TO, PD Encoding: 00 Description: The power-down Status bit, PD is cleared. Time out Status bit, TO is set. Watchdog Timer and its prescaler are cleared. The processor is put into Sleep mode with the oscillator stopped. Words: 1 Cycles: 1 Example: SLEEP DS41206A-page 82 0110 3 ? After Instruction Status Affected: 0000 Before Instruction 0xFF 0; result is negative 0011 Preliminary 2003 Microchip Technology Inc. PIC16F716 SUBWF Subtract W from f SWAPF Swap Nibbles in f Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (f) - (W) → (dest) Operation: Status Affected: C, DC, Z (f<3:0>) → (dest<7:4>), (f<7:4>) → (dest<3:0>) Status Affected: None Encoding: 00 Encoding: 00 Description: Subtract (2’s complement method) W register from register ‘f’. If ‘d’ is 0 the result is stored in the W register. If ‘d’ is 1 the result is stored back in register ‘f’. Description: The upper and lower nibbles of register ‘f’ are exchanged. If ‘d’ is 0 the result is placed in W register. If ‘d’ is 1 the result is placed in register ‘f’. Words: 1 Words: 1 Cycles: 1 Cycles: 1 Example 1: SUBWF Example SWAPF SUBWF f,d 0010 dfff ffff REG1, 1 Before Instruction Example 2: 1 2 1; result is positive 0 1 After Instruction Example 3: TRIS REG1 = 1 W = 2 C = ? [ label ] TRIS Operands: 5≤f≤6 Operation: (W) → TRIS register f; Status Affected: None Encoding: 00 Description: The instruction is supported for code compatibility with the PIC16C5X products. Since TRIS registers are readable and writable, the user can directly address them. Words: 1 Cycles: 1 2003 Microchip Technology Inc. 0000 f 0110 0fff Example After Instruction = = = = Load TRIS Register Syntax: 0 2 1; result is zero DC = 1 Before Instruction REG1 W C Z REG1, 0 REG1 = 0xA5 W = 0x5A REG1 = 2 W = 2 C = ? = = = = ffff After Instruction Before Instruction REG1 W C Z dfff REG1 = 0xA5 After Instruction = = = = = 1110 Before Instruction REG1 = 3 W = 2 C = ? REG1 W C Z DC SWAPF f,d 0xFF 2 0; result is negative DC = 0 Preliminary To maintain upward compatibility with future PICmicro® products, do not use this instruction. DS41206A-page 83 PIC16F716 XORLW Exclusive OR Literal with W XORWF Exclusive OR W with f Syntax: [ label ] Syntax: [ label ] Operands: 0 ≤ k ≤ 255 Operands: 0 ≤ f ≤ 127 d ∈ [0,1] Operation: (W) .XOR. (f) → (dest) Status Affected: Z Encoding: 00 Description: Exclusive OR the contents of the W register with register ‘f’. If ‘d’ is 0 the result is stored in the W register. If ‘d’ is 1 the result is stored back in register ‘f’. Words: 1 Cycles: 1 Example XORWF XORLW k Operation: (W) .XOR. k → (W) Status Affected: Z Encoding: 11 Description: The contents of the W register are XOR’ed with the eight bit literal ‘k’. The result is placed in the W register. 1010 Words: 1 Cycles: 1 Example: XORLW kkkk 0xAF Before Instruction W = 0xB5 kkkk XORWF 0110 f,d dfff ffff REG1, 1 Before Instruction After Instruction REG1 = 0xAF W = 0xB5 W = 0x1A After Instruction REG1 = 0x1A W = 0xB5 DS41206A-page 84 Preliminary 2003 Microchip Technology Inc. PIC16F716 11.0 DEVELOPMENT SUPPORT 11.1 The PICmicro® microcontrollers are supported with a full range of hardware and software development tools: • Integrated Development Environment - MPLAB® IDE Software • Assemblers/Compilers/Linkers - MPASMTM Assembler - MPLAB C17 and MPLAB C18 C Compilers - MPLINKTM Object Linker/ MPLIBTM Object Librarian - MPLAB C30 C Compiler - MPLAB ASM30 Assembler/Linker/Library • Simulators - MPLAB SIM Software Simulator - MPLAB dsPIC30 Software Simulator • Emulators - MPLAB ICE 2000 In-Circuit Emulator - MPLAB ICE 4000 In-Circuit Emulator • In-Circuit Debugger - MPLAB ICD 2 • Device Programmers - PRO MATE® II Universal Device Programmer - PICSTART® Plus Development Programmer • Low Cost Demonstration Boards - PICDEMTM 1 Demonstration Board - PICDEM.netTM Demonstration Board - PICDEM 2 Plus Demonstration Board - PICDEM 3 Demonstration Board - PICDEM 4 Demonstration Board - PICDEM 17 Demonstration Board - PICDEM 18R Demonstration Board - PICDEM LIN Demonstration Board - PICDEM USB Demonstration Board • Evaluation Kits - KEELOQ® - PICDEM MSC - microID® - CAN - PowerSmart® - Analog MPLAB Integrated Development Environment Software The MPLAB IDE software brings an ease of software development previously unseen in the 8/16-bit microcontroller market. The MPLAB IDE is a Windows® based application that contains: • An interface to debugging tools - simulator - programmer (sold separately) - emulator (sold separately) - in-circuit debugger (sold separately) • A full-featured editor with color coded context • A multiple project manager • Customizable data windows with direct edit of contents • High level source code debugging • Mouse over variable inspection • Extensive on-line help The MPLAB IDE allows you to: • Edit your source files (either assembly or C) • One touch assemble (or compile) and download to PICmicro emulator and simulator tools (automatically updates all project information) • Debug using: - source files (assembly or C) - absolute listing file (mixed assembly and C) - machine code MPLAB IDE supports multiple debugging tools in a single development paradigm, from the cost effective simulators, through low cost in-circuit debuggers, to full-featured emulators. This eliminates the learning curve when upgrading to tools with increasing flexibility and power. 11.2 MPASM Assembler The MPASM assembler is a full-featured, universal macro assembler for all PICmicro MCUs. The MPASM assembler generates relocatable object files for the MPLINK object linker, Intel® standard hex files, MAP files to detail memory usage and symbol reference, absolute LST files that contain source lines and generated machine code and COFF files for debugging. The MPASM assembler features include: • Integration into MPLAB IDE projects • User defined macros to streamline assembly code • Conditional assembly for multi-purpose source files • Directives that allow complete control over the assembly process 2003 Microchip Technology Inc. Preliminary DS41206A-page 85 PIC16F716 11.3 MPLAB C17 and MPLAB C18 C Compilers 11.6 The MPLAB C17 and MPLAB C18 Code Development Systems are complete ANSI C compilers for Microchip’s PIC17CXXX and PIC18CXXX family of microcontrollers. These compilers provide powerful integration capabilities, superior code optimization and ease of use not found with other compilers. For easy source level debugging, the compilers provide symbol information that is optimized to the MPLAB IDE debugger. 11.4 MPLINK Object Linker/ MPLIB Object Librarian The MPLINK object linker combines relocatable objects created by the MPASM assembler and the MPLAB C17 and MPLAB C18 C compilers. It can link relocatable objects from pre-compiled libraries, using directives from a linker script. The MPLIB object librarian manages the creation and modification of library files of pre-compiled code. When a routine from a library is called from a source file, only the modules that contain that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. The object linker/library features include: • Efficient linking of single libraries instead of many smaller files • Enhanced code maintainability by grouping related modules together • Flexible creation of libraries with easy module listing, replacement, deletion and extraction 11.5 MPLAB C30 C Compiler MPLAB C30 is distributed with a complete ANSI C standard library. All library functions have been validated and conform to the ANSI C library standard. The library includes functions for string manipulation, dynamic memory allocation, data conversion, timekeeping, and math functions (trigonometric, exponential and hyperbolic). The compiler provides symbolic information for high level source debugging with the MPLAB IDE. DS41206A-page 86 MPLAB ASM30 assembler produces relocatable machine code from symbolic assembly language for dsPIC30F devices. MPLAB C30 compiler uses the assembler to produce it’s object file. The assembler generates relocatable object files that can then be archived or linked with other relocatable object files and archives to create an executable file. Notable features of the assembler include: • • • • • • Support for the entire dsPIC30F instruction set Support for fixed-point and floating-point data Command line interface Rich directive set Flexible macro language MPLAB IDE compatibility 11.7 MPLAB SIM Software Simulator The MPLAB SIM software simulator allows code development in a PC hosted environment by simulating the PICmicro series microcontrollers on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a file, or user defined key press, to any pin. The execution can be performed in Single-Step, Execute Until Break, or Trace mode. The MPLAB SIM simulator fully supports symbolic debugging using the MPLAB C17 and MPLAB C18 C Compilers, as well as the MPASM assembler. The software simulator offers the flexibility to develop and debug code outside of the laboratory environment, making it an excellent, economical software development tool. 11.8 The MPLAB C30 C compiler is a full-featured, ANSI compliant, optimizing compiler that translates standard ANSI C programs into dsPIC30F assembly language source. The compiler also supports many commandline options and language extensions to take full advantage of the dsPIC30F device hardware capabilities, and afford fine control of the compiler code generator. MPLAB ASM30 Assembler, Linker, and Librarian MPLAB SIM30 Software Simulator The MPLAB SIM30 software simulator allows code development in a PC hosted environment by simulating the dsPIC30F series microcontrollers on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a file, or user defined key press, to any of the pins. The MPLAB SIM30 simulator fully supports symbolic debugging using the MPLAB C30 C Compiler and MPLAB ASM30 assembler. The simulator runs in either a Command Line mode for automated tasks, or from MPLAB IDE. This high speed simulator is designed to debug, analyze and optimize time intensive DSP routines. Preliminary 2003 Microchip Technology Inc. PIC16F716 11.9 MPLAB ICE 2000 High Performance Universal In-Circuit Emulator 11.11 MPLAB ICD 2 In-Circuit Debugger The MPLAB ICE 2000 universal in-circuit emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PICmicro microcontrollers. Software control of the MPLAB ICE 2000 in-circuit emulator is advanced by the MPLAB Integrated Development Environment, which allows editing, building, downloading and source debugging from a single environment. The MPLAB ICE 2000 is a full-featured emulator system with enhanced trace, trigger and data monitoring features. Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The universal architecture of the MPLAB ICE in-circuit emulator allows expansion to support new PICmicro microcontrollers. The MPLAB ICE 2000 in-circuit emulator system has been designed as a real-time emulation system with advanced features that are typically found on more expensive development tools. The PC platform and Microsoft® Windows 32-bit operating system were chosen to best make these features available in a simple, unified application. 11.10 MPLAB ICE 4000 High Performance Universal In-Circuit Emulator The MPLAB ICE 4000 universal in-circuit emulator is intended to provide the product development engineer with a complete microcontroller design tool set for highend PICmicro microcontrollers. Software control of the MPLAB ICE in-circuit emulator is provided by the MPLAB Integrated Development Environment, which allows editing, building, downloading and source debugging from a single environment. The MPLAB ICD 4000 is a premium emulator system, providing the features of MPLAB ICE 2000, but with increased emulation memory and high speed performance for dsPIC30F and PIC18XXXX devices. Its advanced emulator features include complex triggering and timing, up to 2 Mb of emulation memory, and the ability to view variables in real-time. Microchip’s In-Circuit Debugger, MPLAB ICD 2, is a powerful, low cost, run-time development tool, connecting to the host PC via an RS-232 or high speed USB interface. This tool is based on the Flash PICmicro MCUs and can be used to develop for these and other PICmicro microcontrollers. The MPLAB ICD 2 utilizes the in-circuit debugging capability built into the Flash devices. This feature, along with Microchip’s In-Circuit Serial ProgrammingTM (ICSPTM) protocol, offers cost effective in-circuit Flash debugging from the graphical user interface of the MPLAB Integrated Development Environment. This enables a designer to develop and debug source code by setting breakpoints, single-stepping and watching variables, CPU status and peripheral registers. Running at full speed enables testing hardware and applications in real-time. MPLAB ICD 2 also serves as a development programmer for selected PICmicro devices. 11.12 PRO MATE II Universal Device Programmer The PRO MATE II is a universal, CE compliant device programmer with programmable voltage verification at VDDMIN and VDDMAX for maximum reliability. It features an LCD display for instructions and error messages and a modular detachable socket assembly to support various package types. In Stand-alone mode, the PRO MATE II device programmer can read, verify, and program PICmicro devices without a PC connection. It can also set code protection in this mode. 11.13 PICSTART Plus Development Programmer The PICSTART Plus development programmer is an easy-to-use, low cost, prototype programmer. It connects to the PC via a COM (RS-232) port. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. The PICSTART Plus development programmer supports most PICmicro devices up to 40 pins. Larger pin count devices, such as the PIC16C92X and PIC17C76X, may be supported with an adapter socket. The PICSTART Plus development programmer is CE compliant. The MPLAB ICE 4000 in-circuit emulator system has been designed as a real-time emulation system with advanced features that are typically found on more expensive development tools. The PC platform and Microsoft Windows 32-bit operating system were chosen to best make these features available in a simple, unified application. 2003 Microchip Technology Inc. Preliminary DS41206A-page 87 PIC16F716 11.14 PICDEM 1 PICmicro Demonstration Board 11.17 PICDEM 3 PIC16C92X Demonstration Board The PICDEM 1 demonstration board demonstrates the capabilities of the PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All necessary hardware and software is included to run basic demo programs. The sample microcontrollers provided with the PICDEM 1 demonstration board can be programmed with a PRO MATE II device programmer, or a PICSTART Plus development programmer. The PICDEM 1 demonstration board can be connected to the MPLAB ICE in-circuit emulator for testing. A prototype area extends the circuitry for additional application components. Features include an RS-232 interface, a potentiometer for simulated analog input, push button switches and eight LEDs. The PICDEM 3 demonstration board supports the PIC16C923 and PIC16C924 in the PLCC package. All the necessary hardware and software is included to run the demonstration programs. 11.15 PICDEM.net Internet/Ethernet Demonstration Board The PICDEM.net demonstration board is an Internet/ Ethernet demonstration board using the PIC18F452 microcontroller and TCP/IP firmware. The board supports any 40-pin DIP device that conforms to the standard pinout used by the PIC16F877 or PIC18C452. This kit features a user friendly TCP/IP stack, web server with HTML, a 24L256 Serial EEPROM for Xmodem download to web pages into Serial EEPROM, ICSP/MPLAB ICD 2 interface connector, an Ethernet interface, RS-232 interface, and a 16 x 2 LCD display. Also included is the book and CD-ROM “TCP/IP Lean, Web Servers for Embedded Systems,” by Jeremy Bentham 11.16 PICDEM 2 Plus Demonstration Board The PICDEM 2 Plus demonstration board supports many 18-, 28-, and 40-pin microcontrollers, including PIC16F87X and PIC18FXX2 devices. All the necessary hardware and software is included to run the demonstration programs. The sample microcontrollers provided with the PICDEM 2 demonstration board can be programmed with a PRO MATE II device programmer, PICSTART Plus development programmer, or MPLAB ICD 2 with a Universal Programmer Adapter. The MPLAB ICD 2 and MPLAB ICE in-circuit emulators may also be used with the PICDEM 2 demonstration board to test firmware. A prototype area extends the circuitry for additional application components. Some of the features include an RS-232 interface, a 2 x 16 LCD display, a piezo speaker, an on-board temperature sensor, four LEDs, and sample PIC18F452 and PIC16F877 Flash microcontrollers. DS41206A-page 88 11.18 PICDEM 4 8/14/18-Pin Demonstration Board The PICDEM 4 can be used to demonstrate the capabilities of the 8-, 14-, and 18-pin PIC16XXXX and PIC18XXXX MCUs, including the PIC16F818/819, PIC16F87/88, PIC16F62XA and the PIC18F1320 family of microcontrollers. PICDEM 4 is intended to showcase the many features of these low pin count parts, including LIN and Motor Control using ECCP. Special provisions are made for low power operation with the super capacitor circuit, and jumpers allow on-board hardware to be disabled to eliminate current draw in this mode. Included on the demo board are provisions for Crystal, RC or Canned Oscillator modes, a five volt regulator for use with a nine volt wall adapter or battery, DB-9 RS-232 interface, ICD connector for programming via ICSP and development with MPLAB ICD 2, 2x16 liquid crystal display, PCB footprints for H-Bridge motor driver, LIN transceiver and EEPROM. Also included are: header for expansion, eight LEDs, four potentiometers, three push buttons and a prototyping area. Included with the kit is a PIC16F627A and a PIC18F1320. Tutorial firmware is included along with the User’s Guide. 11.19 PICDEM 17 Demonstration Board The PICDEM 17 demonstration board is an evaluation board that demonstrates the capabilities of several Microchip microcontrollers, including PIC17C752, PIC17C756A, PIC17C762 and PIC17C766. A programmed sample is included. The PRO MATE II device programmer, or the PICSTART Plus development programmer, can be used to reprogram the device for user tailored application development. The PICDEM 17 demonstration board supports program download and execution from external on-board Flash memory. A generous prototype area is available for user hardware expansion. Preliminary 2003 Microchip Technology Inc. PIC16F716 11.20 PICDEM 18R PIC18C601/801 Demonstration Board 11.23 PICDEM USB PIC16C7X5 Demonstration Board The PICDEM 18R demonstration board serves to assist development of the PIC18C601/801 family of Microchip microcontrollers. It provides hardware implementation of both 8-bit Multiplexed/De-multiplexed and 16-bit memory modes. The board includes 2 Mb external Flash memory and 128 Kb SRAM memory, as well as serial EEPROM, allowing access to the wide range of memory types supported by the PIC18C601/801. The PICDEM USB Demonstration Board shows off the capabilities of the PIC16C745 and PIC16C765 USB microcontrollers. This board provides the basis for future USB products. In addition to the PICDEM series of circuits, Microchip has a line of evaluation kits and demonstration software for these products. 11.21 PICDEM LIN PIC16C43X Demonstration Board The powerful LIN hardware and software kit includes a series of boards and three PICmicro microcontrollers. The small footprint PIC16C432 and PIC16C433 are used as slaves in the LIN communication and feature on-board LIN transceivers. A PIC16F874 Flash microcontroller serves as the master. All three microcontrollers are programmed with firmware to provide LIN bus communication. 11.22 PICkitTM 1 Flash Starter Kit A complete "development system in a box", the PICkit Flash Starter Kit includes a convenient multi-section board for programming, evaluation, and development of 8/14-pin Flash PIC® microcontrollers. Powered via USB, the board operates under a simple Windows GUI. The PICkit 1 Starter Kit includes the user's guide (on CD ROM), PICkit 1 tutorial software and code for various applications. Also included are MPLAB® IDE (Integrated Development Environment) software, software and hardware "Tips 'n Tricks for 8-pin Flash PIC® Microcontrollers" Handbook and a USB Interface Cable. Supports all current 8/14-pin Flash PIC microcontrollers, as well as many future planned devices. 2003 Microchip Technology Inc. 11.24 Evaluation and Programming Tools • KEELOQ evaluation and programming tools for Microchip’s HCS Secure Data Products • CAN developers kit for automotive network applications • Analog design boards and filter design software • PowerSmart battery charging evaluation/ calibration kits • IrDA® development kit • microID development and rfLabTM development software • SEEVAL® designer kit for memory evaluation and endurance calculations • PICDEM MSC demo boards for Switching mode power supply, high power IR driver, delta sigma ADC, and flow rate sensor Check the Microchip web page and the latest Product Line Card for the complete list of demonstration and evaluation kits. Preliminary DS41206A-page 89 PIC16F716 NOTES: DS41206A-page 90 Preliminary 2003 Microchip Technology Inc. PIC16F716 12.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings(†) Ambient temperature under bias......................................................................................................... .-55°C to +125°C Storage temperature ........................................................................................................................... -65°C to +150°C Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4) ....................................... -0.3V to (VDD +0.3V) Voltage on VDD with respect to VSS ...................................................................................................... -0.3V to +7.5V Voltage on MCLR with respect to VSS (Note 2) ...................................................................................... 0V to +13.25V Voltage on RA4 with respect to Vss ............................................................................................................ 0V to +8.5V Total power dissipation (Note 1) (PDIP and SOIC)................................................................................................ 1.0W Total power dissipation (Note 1) (SSOP) ............................................................................................................. 0.65W Maximum current out of VSS pin ........................................................................................................................ 300 mA Maximum current into VDD pin ........................................................................................................................... 250 mA Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................±20 mA Output clamp current, IOK (VO < 0 or VO > VDD) ...........................................................................................................±20 mA Maximum output current sunk by any I/O pin....................................................................................................... 25 mA Maximum output current sourced by any I/O pin ................................................................................................. 25 mA Maximum current sunk by PORTA and PORTB (combined).............................................................................. 200 mA Maximum current sourced by PORTA and PORTB (combined) ........................................................................ 200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - ∑ IOH} + ∑ {(VDD-VOH) x IOH} + ∑(VOl x IOL) 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100Ω should be used when applying a “low” level to the MCLR/VPP pin rather than pulling this pin directly to VSS. † NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. 2003 Microchip Technology Inc. Preliminary DS41206A-page 91 PIC16F716 PIC16F716 VOLTAGE-FREQUENCY GRAPH, -40°C < TA < +85°C(1) FIGURE 12-1: 6.0 5.5 5.0 VDD (Volts) 4.5 4.0 3.5 3.0 2.5 2.0 0 4 10 20 25 Frequency (MHz) Note 1: The shaded region indicates the permissible combinations of voltage and frequency. PIC16F716 VOLTAGE-FREQUENCY GRAPH, 85°C < TA < +125°C(1) FIGURE 12-2: 6.0 5.5 5.0 4.5 VDD (Volts) 4.0 3.5 3.0 2.5 2.0 0 4 10 20 25 Frequency (MHz) Note 1: The shaded region indicates the permissible combinations of voltage and frequency. DS41206A-page 92 Preliminary 2003 Microchip Technology Inc. PIC16F716 12.1 DC Characteristics: PIC16F716 (Industrial, Extended) DC CHARACTERISTICS Param No. Sym VDD Characteristic Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial -40°C ≤ TA ≤ +125°C for extended Min Typ† Max Units Conditions 2.0 3.0 — — 5.5 5.5 V V — 1.5* — V — Vss — V 0.05 TBD — — — — 3.65 4.0 4.35 V BOREN bit set, BOR bit = ‘1’ TBD 2.5 TBD V BOREN bit set, BOR bit = ‘0’ Supply Voltage D001 D001A RAM Data Retention Voltage(1) D002* VDR D003 VPOR VDD Start Voltage to ensure internal Power-on Reset signal D004* SVDD VDD Rise Rate to ensure D004A* internal Power-on Reset signal Industrial Extended See section on Power-on Reset for details V/ms PWRT enabled (PWRTE bit clear) PWRT disabled (PWRTE bit set) See section on Power-on Reset for details VBOR Brown-out Reset voltage trip point D005 * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2003 Microchip Technology Inc. Preliminary DS41206A-page 93 PIC16F716 12.2 DC Characteristics: PIC16F716 (Industrial) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C DC CHARACTERISTICS Para m No. Sym VDD Characteristic 2.0 — — — Max Units VDD Conditions 5.5 V — 0.1 0.8 µA 2.0 0.1 0.85 µA 3.0 — 0.2 2.7 µA 5.0 — 1 2.0 µA 2.0 — 2 3.5 µA 3.0 — 9 13.5 µA 5.0 — TBD TBD µA 3.0 — 40 TBD µA 4.5 — 45 TBD µA 5.0 — 1.8 TBD µA 2.0 — 2.6 TBD µA 3.0 — 3.0 TBD µA 5.0 — 14 17 µA 2.0 — 23 28 µA 3.0 Power-down Base Current D020 ∆IMOD Peripheral Module Current D021 D022 D025 IDD Typ† Supply Voltage D001 IPD Min WDT, BOR and T1OSC: disabled (1) WDT Current BOR Current T1OSC Current Supply Current D010 D011 D012 D013 — 45 60 µA 5.0 — 120 160 µA 2.0 — 180 250 µA 3.0 — 290 370 µA 5.0 — 220 300 µA 2.0 — 350 470 µA 3.0 — 600 780 µA 5.0 — 2.1 2.9 mA 4.5 — 2.5 3.3 mA 5.0 FOSC = 32 kHz LP Oscillator mode FOSC = 1 MHz XT Oscillator mode FOSC = 4 MHz XT Oscillator mode FOSC = 20 MHz HS Oscillator mode † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: The “∆” current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. Max values should be used when calculating total current consumption. 2: ADC on, not converting. DS41206A-page 94 Preliminary 2003 Microchip Technology Inc. PIC16F716 12.3 DC Characteristics: PIC16F716 (Extended) DC CHARACTERISTICS Param No. Sym VDD Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +125°C Characteristic Typ† Max Units VDD Conditions Supply Voltage D001 IPD Min 3.0 — 5.5 V — — 0.1 TBD µA 3.0 — 0.2 TBD µA 5.0 — 2 TBD µA 3.0 9 TBD µA 5.0 TBD TBD µA 3.0 Power-down Base Current D020E WDT, BOR and T1OSC: disabled ∆IMOD Peripheral Module Current(1) D021E — — D022E D025E IDD — 40 TBD µA 4.5 — 45 TBD µA 5.0 — 2.6 TBD µA 3.0 — 3.0 TBD µA 5.0 — 21 TBD µA 3.0 WDT Current BOR Current T1OSC Current Supply Current D010E D011E D012E D013E — 38 TBD µA 5.0 — 182 TBD µA 3.0 — 293 TBD µA 5.0 — 371 TBD µA 3.0 — 668 TBD µA 5.0 — 2.6 TBD mA 4.5 — 3 TBD mA 5.0 FOSC = 32 kHz LP Oscillator mode FOSC = 1 MHz XT Oscillator mode FOSC = 4 MHz XT Oscillator mode FOSC = 20 MHz HS Oscillator mode † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: The “∆” current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. Max values should be used when calculating total current consumption. 2: ADC on, not converting. 2003 Microchip Technology Inc. Preliminary DS41206A-page 95 PIC16F716 12.4 DC Characteristics: PIC16F716 (Industrial, Extended) Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial -40°C ≤ TA ≤ +125°C for extended Operating voltage VDD range as described in DC spec Section 12.1 “DC Characteristics: PIC16F716 (Industrial, Extended)” and Section 12.4 “DC Characteristics: PIC16F716 (Industrial, Extended)”. DC CHARACTERISTICS Param No. Sym VIL D030 D030A D031 D032 D033 VIH D040 D040A D041 D042 D042A D043 D060 IIL D061 D063 D070 IPURB D080 VOL D083 Characteristic Input Low Voltage I/O ports with TTL buffer with Schmitt Trigger buffer MCLR, OSC1 (in RC mode) OSC1 (in HS mode) OSC1 (in XT and LP modes) Input High Voltage I/O ports with TTL buffer Min Typ† Max Units VSS VSS VSS VSS VSS VSS — — — — — — 0.8 0.15 VDD 0.2 VDD 0.2 VDD 0.3 VDD 0.6 V V V V V V — — — VDD VDD V V 4.5V ≤ VDD ≤ 5.5V otherwise — — — — VDD VDD VDD VDD V V V V For entire VDD range with Schmitt Trigger buffer MCLR OSC1 (XT, HS and LP modes) OSC1 (in RC mode) 2.0 0.25 VDD + 0.8V 0.8 VDD 0.8 VDD 0.7 VDD 0.9 VDD Input Leakage Current(2), (3) I/O ports — — ±1 µA — — ±500 nA MCLR, RA4/T0CKI OSC1/CLKIN — — — — ±5 ±5 µA µA PORTB weak pull-up current Output Low Voltage I/O ports 50 250 400 µA — — 0.6 V — — 0.6 V — — 0.6 V — — 0.6 V VDD-0.7 — — V VDD-0.7 — — V VDD-0.7 — — V VDD-0.7 — — V OSC2/CLKOUT (RC Osc mode) Conditions 4.5V ≤ VDD ≤ 5.5V otherwise (Note1) (Note1) Vss ≤ VPIN ≤ VDD, Pin at high-impedance Vss ≤ VPIN ≤ VDD, Pin configured as analog input Vss ≤ VPIN ≤ VDD Vss ≤ VPIN ≤ VDD, XT, HS and LP osc modes VDD = 5V, VPIN = VSS IOL = 8.5 mA, VDD = 4.5V, -40°C to +85°C IOL = 7.0 mA, VDD = 4.5V, -40°C to +125°C IOL = 1.6 mA, VDD = 4.5V, -40°C to +85°C IOL = 1.2 mA, VDD = 4.5V, -40°C to +125°C Output High Voltage D090 VOH D092 D150* Note I/O ports(3) OSC2/CLKOUT (RC Osc mode) IOH = -3.0 mA, VDD = 4.5V, -40°C to +85°C IOH = -2.5 mA, VDD = 4.5V, -40°C to +125°C IOH = -1.3 mA, VDD = 4.5V, -40°C to +85°C IOH = -1.0 mA, VDD = 4.5V, -40°C to +125°C RA4 pin Open-Drain High Voltage — — 8.5 V VOD These parameters are characterized but not tested. Data in “Type” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with external clock in RC mode. 2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. * † 1: DS41206A-page 96 Preliminary 2003 Microchip Technology Inc. PIC16F716 Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial -40°C ≤ TA ≤ +125°C for extended Operating voltage VDD range as described in DC spec Section 12.1 “DC Characteristics: PIC16F716 (Industrial, Extended)” and Section 12.4 “DC Characteristics: PIC16F716 (Industrial, Extended)”. DC CHARACTERISTICS Param No. Sym Note Min Typ† Max Units Conditions — 15 pF In XT, HS and LP modes when external clock is used to drive OSC1. Capacitive Loading Specs on Output Pins COSC2 OSC2/CLKOUT pin — D100 D101 Characteristic All I/O pins and OSC2 (in RC mode) — — 50 pF CIO These parameters are characterized but not tested. Data in “Type” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. In RC Oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PICmicro be driven with external clock in RC mode. 2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin. * † 1: 12.5 12.5.1 AC (Timing) Characteristics TIMING PARAMETER SYMBOLOGY The timing parameter symbols have been created using one of the following formats: 1. TppS2ppS 2. TppS T F Frequency Lowercase letters (pp) and their meanings: pp cc CCP1 ck CLKOUT cs CS di SDI do SDO dt Data in io I/O port mc MCLR Uppercase letters and their meanings: S F Fall H High I Invalid (Hi-impedance) L Low 2003 Microchip Technology Inc. T Time osc rd rw sc ss t0 t1 wr OSC1 RD RD or WR SCK SS T0CKI T1CKI WR P R V Z Period Rise Valid Hi-impedance Preliminary DS41206A-page 97 PIC16F716 12.5.2 TIMING CONDITIONS The temperature and voltages specified in Table 12-1 apply to all timing specifications, unless otherwise noted. Figure 12-3 specifies the load conditions for the timing specifications. TABLE 12-1: TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC AC CHARACTERISTICS FIGURE 12-3: Standard Operating Conditions (unless otherwise stated) Operating temperature -40°C ≤ TA ≤ +85°C for industrial -40°C ≤ TA ≤ +125°C for extended Operating voltage VDD range as described in DC spec Section 12.1 “DC Characteristics: PIC16F716 (Industrial, Extended)” and Section 12.4 “DC Characteristics: PIC16F716 (Industrial, Extended)”. LC parts operate for commercial/industrial temp’s only. LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS Load condition 2 Load condition 1 VDD/2 Rl Cl Pin VSS Cl Pin VSS RL = 464Ω CL = 50 pF for all pins except OSC2/CLKOUT 15 pF for OSC2 output 12.5.3 TIMING DIAGRAMS AND SPECIFICATIONS FIGURE 12-4: EXTERNAL CLOCK TIMING Q4 Q1 Q2 Q3 Q4 Q1 OSC1 3 1 3 4 4 2 CLKOUT DS41206A-page 98 Preliminary 2003 Microchip Technology Inc. PIC16F716 TABLE 12-2: Param No. Sym EXTERNAL CLOCK TIMING REQUIREMENTS Characteristic Min Typ† Max Units Conditions Ext. Clock Input Frequency(1) DC — 4 MHz RC and XT Osc modes DC — 20 MHz HS Osc mode DC — 200 kHz LP Osc mode (1) Oscillator Frequency DC — 4 MHz RC Osc mode 0.1 — 4 MHz XT Osc mode 4 — 20 MHz HS Osc mode 5 — 200 kHz LP Osc mode 1 TOSC External CLKIN Period(1) 250 — — ns RC and XT Osc modes 50 — — ns HS Osc mode 5 — — µs LP Osc mode Oscillator Period(1) 250 — — ns RC Osc mode 250 — 10,000 ns XT Osc mode 50 — 250 ns HS Osc mode 5 — — µs LP Osc mode 2 Tcy Instruction Cycle Time(1) 200 — DC ns TCY = 4/FOSC 3* TosL, External Clock in (OSC1) High or 100 — — ns XT oscillator TosH Low Time 2.5 — — µs LP oscillator 15 — — ns HS oscillator 4* TosR, External Clock in (OSC1) Rise or — — 25 ns XT oscillator TosF Fall Time — — 50 ns LP oscillator — — 15 ns HS oscillator * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices. 1A FOSC 2003 Microchip Technology Inc. Preliminary DS41206A-page 99 PIC16F716 FIGURE 12-5: CLKOUT AND I/O TIMING Q1 Q4 Q2 Q3 OSC1 11 10 CLKOUT 13 19 14 12 18 16 I/O Pin (input) 15 17 I/O Pin (output) new value old value 20, 21 Note 1: Refer to Figure 12-3 for load conditions. TABLE 12-3: Param No. CLKOUT AND I/O TIMING REQUIREMENTS Sym Characteristic Min Typ † Max Units Conditions 10* TOSH2CKL OSC1↑ to CLKOUT↓ — 75 200 ns (Note 1) 11* TOSH2CKH OSC1↑ to CLKOUT↑ — 75 200 ns (Note 1) 12* TCKR CLKOUT rise time — 35 100 ns (Note 1) 13* TCKF CLKOUT fall time — 35 100 ns (Note 1) — — 20 ns (Note 1) TOSC + 200 — — ns (Note 1) (Note 1) 14* TCKL2IOV CLKOUT ↓ to Port out valid 15* TIOV2CKH Port input valid before CLKOUT ↑ 16* TCKH2IOI Port input hold after CLKOUT ↑ 0 — — ns 17* TOSH2IOV OSC1↑ (Q1 cycle) to Port out valid — 50 150 ns 18* TOSH2IOI OSC1↑ (Q2 cycle) to Port input invalid (I/O in hold time) 18A* Standard 100 — — ns Extended (LC) 200 — — ns 19* TIOV2OSH Port input valid to OSC1↑ (I/O in setup time) 0 — — ns 20* TIOR Port output rise time Standard — 10 40 ns Extended (LC) — — 80 ns TIOF Port output fall time Standard — 10 40 ns — — 80 ns 22††* TINP INT pin high or low time Tcy — — ns 23††* TRBP RB7:RB4 change INT high or low time Tcy — — ns 20A* 21* 21A* Extended (LC) * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. †† These parameters are asynchronous events not related to any internal clock edge. Note 1: Measurements are taken in RC mode where CLKOUT output is 4 x TOSC. DS41206A-page 100 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 12-6: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING(1) VDD MCLR 30 Internal POR 33 PWRT Time-out 32 OSC Time-out Internal Reset Watchdog Timer Reset 31 34 34 I/O Pins Note 1: Refer to Figure 12-3 for load conditions. FIGURE 12-7: BROWN-OUT RESET TIMING BVDD VDD TABLE 12-4: Param No. Sym 35 RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER, AND BROWN-OUT RESET REQUIREMENTS Characteristic Min Typ† Max Units Conditions 30 TMCL MCLR Pulse Width (low) 2 — — µs VDD = 5V, -40°C to +125°C 31* TWDT Watchdog Timer Time-out Period 7 18 33 ms VDD = 5V, -40°C to +85°C TBD TBD TBD ms VDD = 5V, +85°C to +125°C 32 TOST Oscillation Start-up Timer Period — 1024 TOSC — — TOSC = OSC1 period 33* TPWRT Power-up Timer Period 28 72 132 ms VDD = 5V, -40°C to +85°C TBD TBD TBD ms VDD = 5V, +85°C to +125°C 34 TIOZ I/O high-impedance from MCLR Low or WDT Reset — — 2.1 µs TBOR Brown-out Reset Pulse Width 100 — — µs (No Prescaler) 35 VDD ≤ BVDD (D005) * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. 2003 Microchip Technology Inc. Preliminary DS41206A-page 101 PIC16F716 TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS(1) FIGURE 12-8: T0CKI 41 40 42 T1OSO/T1CKI 46 45 47 48 TMR0 or TMR1 Note 1: Refer to Figure 12-3 for load conditions. TABLE 12-5: Param No. TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS Sym Characteristic 40* Tt0H T0CKI High Pulse Width 41* Tt0L T0CKI Low Pulse Width 42* Tt0P T0CKI Period No Prescaler With Prescaler No Prescaler With Prescaler No Prescaler With Prescaler T1CKI High Time Synchronous, Prescaler = 1 Synchronous, Standard Prescaler = 2,4,8 Asynchronous Standard T1CKI Low Time Synchronous, Prescaler = 1 Synchronous, Standard Prescaler = 2,4,8 Asynchronous Standard T1CKI input Synchronous Standard period Min Typ† Max Units Conditions 0.5TCY + 20 10 0.5TCY + 20 10 TCY + 40 Greater of: 20 or TCY + 40 N 0.5TCY + 20 15 — — — — — — — — — — — — ns ns ns ns ns ns — — — — ns ns N = prescale value (2, 4,..., 256) Must also meet parameter 47 30 0.5TCY + 20 15 — — — — — — ns ns ns Must also meet parameter 47 30 Greater of: 30 OR TCY + 40 N 60 32.768 — — — — ns ns Must also meet parameter 42 Must also meet parameter 42 45* Tt1H 46* Tt1L 47* Tt1P 48* Asynchronous Standard — — ns Timer1 oscillator input frequency range — 32.768 kHz (oscillator enabled by setting bit T1OSCEN) TCKEZtmr1 Delay from external clock edge to timer increment 2Tosc — 7Tosc — * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Ft1 DS41206A-page 102 Preliminary N = prescale value (1, 2, 4, 8) 2003 Microchip Technology Inc. PIC16F716 FIGURE 12-9: CAPTURE/COMPARE/PWM TIMINGS(1) CCP1 (Capture Mode) 50 51 52 CCP1 (Compare or PWM Mode) 53 Note 1: Refer to Figure 12-3 for load conditions. TABLE 12-6: CAPTURE/COMPARE/PWM REQUIREMENTS Param Sym No. 50* 51* TccL CCP1 input low time Characteristic Min — — ns 10 — — ns 0.5TCY + 20 — — ns 10 — — ns 3TCY + 40 N — — ns Standard — 10 40 ns Extended — — 80 ns Standard — 10 40 ns Extended — — 80 ns With Prescaler Standard TccH CCP1 input high No Prescaler time With Prescaler Standard TccP CCP1 input period 53* TccR CCP1 output rise time 53A* TccF CCP1 output fall time 54A* Typ Max Units † 0.5TCY + 20 No Prescaler 52* 54* 54 Conditions N = prescale value (1,4, or 16) * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. 2003 Microchip Technology Inc. Preliminary DS41206A-page 103 PIC16F716 TABLE 12-7: Para m No. A/D CONVERTER CHARACTERISTICS: PIC16F716 (INDUSTRIAL, EXTENDED) Sym Characteristic A00 VDD VDD Operation A01 NR A02 Resolution EABS Total Absolute error Min Typ† Max Units Conditions 2.5 — 5.5 V — — 8-bits bit — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF A03 EIL Integral linearity error — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF A04 EDL Differential linearity error — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF A05 EFS Full scale error — — <±1 LSb VREF = VDD= 5.12V, VSS ≤ VAIN ≤ VREF A06 EOFF Offset error — — <±1 LSb VREF = VDD = 5.12V, VSS ≤ VAIN ≤ VREF Monotonicity — guaranteed(3) — — A20 VREF Reference voltage 2.5V — VDD + 0.3 V A25 VAIN Analog input voltage VSS 0.3 — VREF + 0.3 V A30 ZAIN Recommended impedance of analog voltage source — — 10.0 kΩ A40 IAD — 180 — µA Average current consumption when A/D is on.(1) A50 IREF VREF input current(2) 10 — 1000 µA — — 10 µA During VAIN acquisition. Based on differential of VHOLD to VAIN to charge CHOLD, see Section 12.1 “DC Characteristics: PIC16F716 (Industrial, Extended)”. During A/D Conversion cycle A10 — A/D conversion current (VDD) Standard VSS ≤ VAIN ≤ VREF * These parameters are characterized but not tested. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. 2: VREF current is from RA3 pin or VDD pin, whichever is selected as reference input. 3: The A/D conversion result never decreases with an increase in the input voltage, and has no missing codes. DS41206A-page 104 Preliminary 2003 Microchip Technology Inc. PIC16F716 FIGURE 12-10: A/D CONVERSION TIMING BSF ADCON0, GO 134 1 Tcy (TOSC/2)(1) 131 Q4 130 A/D CLK 132 7 A/D DATA 6 5 4 3 2 1 0 NEW_DATA OLD_DATA ADRES ADIF GO DONE SAMPLING STOPPED SAMPLE Note 1: TABLE 12-8: Param No. Sym 130 TAD If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. A/D CONVERSION REQUIREMENTS Characteristic A/D clock period Min Typ† Max Units Conditions Industrial 1.6 — — µs TOSC based, VREF ≥ 3.0V Industrial 1.6 4.0 6.0 µs A/D RC mode Extended 1.6 — — µs TOSC based, VREF ≥ 3.0V Extended 1.6 6.0 9.0 µs A/D RC mode 131 TCNV Conversion time (not including S/H time)(1) 132 TACQ Acquisition time 134 TGO 135 TSWC Switching from convert → sample time Q4 to A/D clock start 9.5 — 9.5 TAD (Note 2) 20 — µs 5* — — µs The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 20.0 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). — TOSC/2 ** — — If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed. 1.5 ** — — TAD * These parameters are characterized but not tested. ** This specification ensured by design. † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: ADRES register may be read on the following TCY cycle. 2: See Section 12.1 “DC Characteristics: PIC16F716 (Industrial, Extended)” for min. conditions. 2003 Microchip Technology Inc. Preliminary DS41206A-page 105 PIC16F716 NOTES: DS41206A-page 106 Preliminary 2003 Microchip Technology Inc. PIC16F716 13.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES The graphs and tables provided in this section are for design guidance and are not tested. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices will operate properly only within the specified range. The data presented in this section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. 'Typical' represents the mean of the distribution at 25°C. 'Max' or 'min' represents (mean + 3σ) or (mean - 3σ) respectively, where σ is standard deviation, over the whole temperature range. Graphs and Tables not available at this time. 2003 Microchip Technology Inc. Preliminary DS41206A-page 107 PIC16F716 NOTES: DS41206A-page 108 Preliminary 2003 Microchip Technology Inc. PIC16F716 14.0 PACKAGING INFORMATION 14.1 Package Marking Information 18-Lead PDIP Example XXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXX YYWWNNN 18-Lead SOIC PIC16F716-04/P 0023CBA Example XXXXXXXXXXXX XXXXXXXXXXXX XXXXXXXXXXXX YYWWNNN 20-Lead SSOP PIC16F716 -20/SO 0018CDK Example PIC16F716 -20I/SS025 XXXXXXXXXXX XXXXXXXXXXX YYWWNNN Legend: XX...X Y YY WW NNN Note: * 0020CBK Customer specific information* Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week ‘01’) Alphanumeric traceability code In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information. Standard PICmicro device marking consists of Microchip part number, year code, week code, and traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price. 2003 Microchip Technology Inc. Preliminary DS41206A-page 109 PIC16F716 18-Lead Plastic Dual In-line (P) – 300 mil (PDIP) E1 D 2 n α 1 E A2 A L c A1 B1 β p B eB Units Dimension Limits n p MIN INCHES* NOM 18 .100 .155 .130 MAX MILLIMETERS NOM 18 2.54 3.56 3.94 2.92 3.30 0.38 7.62 7.94 6.10 6.35 22.61 22.80 3.18 3.30 0.20 0.29 1.14 1.46 0.36 0.46 7.87 9.40 5 10 5 10 MIN Number of Pins Pitch Top to Seating Plane A .140 .170 Molded Package Thickness A2 .115 .145 Base to Seating Plane A1 .015 Shoulder to Shoulder Width E .300 .313 .325 Molded Package Width E1 .240 .250 .260 Overall Length D .890 .898 .905 Tip to Seating Plane L .125 .130 .135 c Lead Thickness .008 .012 .015 Upper Lead Width B1 .045 .058 .070 Lower Lead Width B .014 .018 .022 Overall Row Spacing § eB .310 .370 .430 α Mold Draft Angle Top 5 10 15 β Mold Draft Angle Bottom 5 10 15 * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-001 Drawing No. C04-007 DS41206A-page 110 Preliminary MAX 4.32 3.68 8.26 6.60 22.99 3.43 0.38 1.78 0.56 10.92 15 15 2003 Microchip Technology Inc. PIC16F716 18-Lead Plastic Small Outline (SO) – Wide, 300 mil (SOIC) E p E1 D 2 B n 1 h α 45° c A2 A φ β L Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Chamfer Distance Foot Length Foot Angle Lead Thickness Lead Width Mold Draft Angle Top Mold Draft Angle Bottom A A2 A1 E E1 D h L φ c B α β MIN .093 .088 .004 .394 .291 .446 .010 .016 0 .009 .014 0 0 A1 INCHES* NOM 18 .050 .099 .091 .008 .407 .295 .454 .020 .033 4 .011 .017 12 12 MAX .104 .094 .012 .420 .299 .462 .029 .050 8 .012 .020 15 15 MILLIMETERS NOM 18 1.27 2.36 2.50 2.24 2.31 0.10 0.20 10.01 10.34 7.39 7.49 11.33 11.53 0.25 0.50 0.41 0.84 0 4 0.23 0.27 0.36 0.42 0 12 0 12 MIN MAX 2.64 2.39 0.30 10.67 7.59 11.73 0.74 1.27 8 0.30 0.51 15 15 * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MS-013 Drawing No. C04-051 2003 Microchip Technology Inc. Preliminary DS41206A-page 111 PIC16F716 20-Lead Plastic Shrink Small Outline (SS) – 209 mil, 5.30 mm (SSOP) E E1 p D B 2 1 n α c A2 A φ L A1 β Units Dimension Limits n p Number of Pins Pitch Overall Height Molded Package Thickness Standoff § Overall Width Molded Package Width Overall Length Foot Length Lead Thickness Foot Angle Lead Width Mold Draft Angle Top Mold Draft Angle Bottom A A2 A1 E E1 D L c φ B α β MIN .068 .064 .002 .299 .201 .278 .022 .004 0 .010 0 0 INCHES* NOM 20 .026 .073 .068 .006 .309 .207 .284 .030 .007 4 .013 5 5 MAX .078 .072 .010 .322 .212 .289 .037 .010 8 .015 10 10 MILLIMETERS NOM 20 0.65 1.73 1.85 1.63 1.73 0.05 0.15 7.59 7.85 5.11 5.25 7.06 7.20 0.56 0.75 0.10 0.18 0.00 101.60 0.25 0.32 0 5 0 5 MIN MAX 1.98 1.83 0.25 8.18 5.38 7.34 0.94 0.25 203.20 0.38 10 10 * Controlling Parameter § Significant Characteristic Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side. JEDEC Equivalent: MO-150 Drawing No. C04-072 DS41206A-page 112 Preliminary 2003 Microchip Technology Inc. PIC16F716 APPENDIX A: REVISION HISTORY APPENDIX B: Revision A (June 2003) Original data sheet. However, the device described in this data sheet are upgrades to PIC16C716. 2003 Microchip Technology Inc. CONVERSION CONSIDERATIONS This is a Flash program memory version of the PIC16C716 device. Refer to the migration document, DS40059, for more information about differences between the PIC16F716 and PIC16C716. Preliminary DS41206A-page 113 PIC16F716 APPENDIX C: MIGRATION FROM BASE-LINE TO MID-RANGE DEVICES To convert code written for PIC16C5X to PIC16F716, the user should take the following steps: 1. This section discusses how to migrate from a baseline device (i.e., PIC16C5X) to a mid-range device (i.e., PIC16F716). 2. The following are the list of modifications over the PIC16C5X microcontroller family: 3. 1. 4. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Instruction word length is increased to 14-bits. This allows larger page sizes both in program memory (2K now as opposed to 512 before) and register file (128 bytes now versus 32 bytes before). A PC high latch register (PCLATH) is added to handle program memory paging. Bits PA2, PA1, PA0 are removed from Status register. Data memory paging is redefined slightly. Status register is modified. Four new instructions have been added: RETURN, RETFIE, ADDLW, and SUBLW. Two instructions TRIS and OPTION are being phased out although they are kept for compatibility with PIC16C5X. OPTION_REG and TRIS registers are made addressable. Interrupt capability is added. Interrupt vector is at 0004h. Stack size is increased to 8 deep. Reset vector is changed to 0000h. Reset of all registers is revisited. Five different Reset (and wake-up) types are recognized. Registers are reset differently. Wake-up from Sleep through interrupt is added. Two separate timers, Oscillator Start-up Timer (OST) and Power-up Timer (PWRT) are included for more reliable power-up. These timers are invoked selectively to avoid unnecessary delays on power-up and wake-up. PORTB has weak pull-ups and interrupt-onchange feature. T0CKI pin is also a port pin (RA4) now. FSR is made a full eight bit register. “In-circuit serial programming” is made possible. The user can program PIC16F716 devices using only five pins: VDD, VSS, MCLR/VPP, RB6 (clock) and RB7 (data in/out). PCON status register is added with a Power-on Reset Status bit (POR). Brown-out protection circuitry has been added. Controlled by configuration word bits BOREN and BORV. Brown-out Reset ensures the device is placed in a Reset condition if VDD dips below a fixed setpoint. DS41206A-page 114 Remove any program memory page select operations (PA2, PA1, PA0 bits) for CALL, GOTO. Revisit any computed jump operations (write to PC or add to PC, etc.) to make sure page bits are set properly under the new scheme. Eliminate any data memory page switching. Redefine data variables to reallocate them. Verify all writes to Status, Option, and FSR registers since these have changed. Change Reset vector to 0000h 5. . Note 1: This device has been designed to perform to the parameters of its data sheet. It has been tested to an electrical specification designed to determine its conformance with these parameters. Due to process differences in the manufacture of this device, this device may have different performance characteristics than its earlier version. These differences may cause this device to perform differently in your application than the earlier version of this device. Preliminary 2: The user should verify that the device oscillator starts and performs as expected. Adjusting the loading capacitor values and/or the Oscillator mode may be required. 2003 Microchip Technology Inc. PIC16F716 ON-LINE SUPPORT Microchip provides on-line support on the Microchip World Wide Web site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape® or Microsoft® Internet Explorer. Files are also available for FTP download from our FTP site. SYSTEMS INFORMATION AND UPGRADE HOT LINE The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive the most current upgrade kits. The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-792-7302 for the rest of the world. Connecting to the Microchip Internet Web Site 042003 The Microchip web site is available at the following URL: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: • Latest Microchip Press Releases • Technical Support Section with Frequently Asked Questions • Design Tips • Device Errata • Job Postings • Microchip Consultant Program Member Listing • Links to other useful web sites related to Microchip Products • Conferences for products, Development Systems, technical information and more • Listing of seminars and events 2003 Microchip Technology Inc. Preliminary DS41206A-page 115 PIC16F716 READER RESPONSE It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150. Please list the following information, and use this outline to provide us with your comments about this document. To: Technical Publications Manager RE: Reader Response Total Pages Sent ________ From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ FAX: (______) _________ - _________ Application (optional): Would you like a reply? Device: PIC16F716 Y N Literature Number: DS41206A Questions: 1. What are the best features of this document? 2. How does this document meet your hardware and software development needs? 3. Do you find the organization of this document easy to follow? If not, why? 4. What additions to the document do you think would enhance the structure and subject? 5. What deletions from the document could be made without affecting the overall usefulness? 6. Is there any incorrect or misleading information (what and where)? 7. How would you improve this document? DS41206A-page 116 Preliminary 2003 Microchip Technology Inc. PIC16F716 INDEX A A/D ...................................................................................... 49 A/D Converter Enable (ADIE Bit) ................................ 14 A/D Converter Flag (ADIF Bit) .............................. 15, 50 A/D Converter Interrupt, Configuring .......................... 50 ADCON0 Register................................................... 9, 49 ADCON1 Register................................................. 10, 50 ADRES Register ........................................................... 9 Analog Port Pins, Configuring..................................... 52 Channel Select (CHS2:CHS0 Bits) ............................. 49 Clock Select (ADCS1:ADCS0 Bits)............................. 49 Configuring the Module............................................... 50 Conversion Clock (Tad) .............................................. 52 Conversion Status (GO/DONE Bit) ....................... 49, 50 Conversions ................................................................ 53 Converter Characteristics ......................................... 104 Module On/Off (ADON Bit).......................................... 49 Port Configuration Control (PCFG2:PCFG0 Bits) ....... 50 Sampling Requirements.............................................. 51 Special Event Trigger (CCP)................................. 35, 53 Timing Diagram......................................................... 105 Absolute Maximum Ratings ................................................ 91 ADCON0 Register................................................................. 9 ADCON1 Register............................................................... 10 ADDLW Instruction ............................................................. 73 ADDWF Instruction ............................................................. 73 ADRES Register ................................................................... 9 Analog Input Model ............................................................. 51 Analog-to-Digital Converter. See A/D ANDLW Instruction ............................................................. 73 ANDWF Instruction ............................................................. 73 Assembler MPASM Assembler..................................................... 85 B Banking, Data Memory ................................................... 7, 11 BCF Instruction ................................................................... 74 Block Diagrams A/D .............................................................................. 51 Capture (CCP Module) ............................................... 34 Compare (CCP Module) ............................................. 35 Interrupt Sources ........................................................ 65 On-Chip Reset Circuit ................................................. 60 PIC16F716.................................................................... 5 PORTA.................................................................. 19, 20 PORTB........................................................................ 21 PWM (CCP Module) ................................................... 36 PWM (Enhanced)........................................................ 38 RB1/T1OSO/T1CKI..................................................... 22 RB2/T1OSI.................................................................. 22 RB3/CCP1/P1A........................................................... 23 RB4 ............................................................................. 23 RB5 ............................................................................. 24 RB6/P1C ..................................................................... 24 RB7/P1D ..................................................................... 25 Timer0......................................................................... 27 Timer0/WDT Prescaler ............................................... 28 Timer1......................................................................... 30 Timer2......................................................................... 32 Watchdog Timer (WDT) .............................................. 67 BOR. See Brown-out Reset Brown-out Detect (BOD) ..................................................... 59 Brown-out Reset (BOR) .................................... 55, 58, 62, 63 2003 Microchip Technology Inc. BOR Enable (BODEN Bit) .......................................... 56 BOR Status (BOR Bit) ................................................ 16 Timing Diagram ........................................................ 101 BSF Instruction ................................................................... 74 BTFSC Instruction .............................................................. 74 BTFSS Instruction............................................................... 75 C C Compilers MPLAB C17................................................................ 86 MPLAB C18................................................................ 86 MPLAB C30................................................................ 86 CALL Instruction ................................................................. 75 Capture (CCP Module) ....................................................... 34 CCP Pin Configuration ............................................... 34 CCPR1H:CCPR1L Registers ..................................... 34 Software Interrupt ....................................................... 34 Timer1 Mode Selection............................................... 34 Capture/Compare/PWM (CCP) .......................................... 33 Capture Mode. See Capture CCP1CON Register...................................................... 9 CCPR1H Register .................................................. 9, 33 CCPR1L Register ................................................... 9, 33 Compare Mode. See Compare Enable (CCP1IE Bit)................................................... 14 Flag (CCP1IF Bit) ....................................................... 15 PWM Mode. See PWM Timer Resources ........................................................ 33 Timing Diagram ........................................................ 103 CLRF Instruction................................................................. 75 CLRW Instruction................................................................ 76 CLRWDT Instruction........................................................... 76 Code Examples Capture (CCP Module) Changing Between Capture Prescalers ............. 34 How to Clear RAM Using Indirect Addressing............ 18 Initializing PORTA ...................................................... 19 Initializing PORTB ...................................................... 21 Code Protection ............................................................ 55, 69 CP1:CP0 Bits.............................................................. 56 COMF Instruction................................................................ 76 Compare (CCP Module) ..................................................... 34 CCP Pin Configuration ............................................... 35 Software Interrupt ....................................................... 35 Special Event Trigger ..................................... 30, 35, 53 Timer1 Mode Selection............................................... 35 Configuration Bits ............................................................... 55 Conversion Considerations............................................... 113 D Data Memory ........................................................................ 7 Bank Select (RP1:RP0 Bits) ................................... 7, 11 General Purpose Registers .......................................... 8 Register File Map ......................................................... 8 Special Function Registers........................................... 9 DC Characteristics............................................ 93, 94, 95, 96 DECF Instruction ................................................................ 76 DECFSZ Instruction............................................................ 77 Demonstration Boards PICDEM 1................................................................... 88 PICDEM 17................................................................. 88 PICDEM 18R PIC18C601/801 ................................... 89 PICDEM 2 Plus........................................................... 88 PICDEM 3 PIC16C92X............................................... 88 Preliminary DS41206A-page 117 PIC16F716 PICDEM 4 ................................................................... 88 PICDEM LIN PIC16C43X ........................................... 89 PICDEM USB PIC16C7X5.......................................... 89 PICDEM.net Internet/Ethernet .................................... 88 Development Support ......................................................... 85 Direct Addressing................................................................ 18 E ECCP Auto-Shutdown ........................................................... 45 and Automatic Restart ........................................ 47 Start-up Considerations .............................................. 47 Electrical Characteristics..................................................... 91 Enhanced Capture/Compare/PWM (ECCP) PWM Mode. See PWM (ECCP Module) Enhanced CCP Auto-Shutdown.......................................... 45 Enhanced PWM Mode. See PWM (ECCP Module)............ 38 Errata .................................................................................... 3 Evaluation and Programming Tools .................................... 89 External Power-on Reset Circuit ......................................... 58 G GOTO Instruction ................................................................ 77 I I/O Ports .............................................................................. 19 ID Locations .................................................................. 55, 69 INCF Instruction .................................................................. 78 INCFSZ Instruction.............................................................. 78 In-Circuit Serial Programming (ICSP) ........................... 55, 69 Indirect Addressing ............................................................. 18 FSR Register ...................................................... 8, 9, 18 INDF Register ............................................................... 9 Instruction Set ADDLW ....................................................................... 73 ADDWF ....................................................................... 73 ANDLW ....................................................................... 73 ANDWF ....................................................................... 73 BCF ............................................................................. 74 BSF ............................................................................. 74 BTFSC ........................................................................ 74 BTFSS ........................................................................ 75 CALL ........................................................................... 75 CLRF........................................................................... 75 CLRW ......................................................................... 76 CLRWDT..................................................................... 76 COMF ......................................................................... 76 DECF .......................................................................... 76 DECFSZ...................................................................... 77 GOTO ......................................................................... 77 INCF............................................................................ 78 INCFSZ ....................................................................... 78 IORLW ........................................................................ 79 IORWF ........................................................................ 79 MOVF.......................................................................... 79 MOVLW ...................................................................... 79 MOVWF ...................................................................... 80 NOP ............................................................................ 80 OPTION ...................................................................... 80 RETFIE ....................................................................... 80 RETLW ....................................................................... 81 RETURN ..................................................................... 81 RLF ............................................................................. 81 RRF............................................................................. 82 SLEEP ........................................................................ 82 SUBLW ....................................................................... 82 DS41206A-page 118 SUBWF....................................................................... 83 SWAPF ....................................................................... 83 TRIS ........................................................................... 83 XORLW ...................................................................... 84 XORWF ...................................................................... 84 Instruction Set Summary .................................................... 71 INT Interrupt (RB0/INT). See Interrupt Sources INTCON Register............................................................ 9, 13 GIE Bit ........................................................................ 13 INTE Bit ...................................................................... 13 INTF Bit ...................................................................... 13 PEIE Bit ...................................................................... 13 RBIE Bit ...................................................................... 13 RBIF Bit ...................................................................... 13 T0IE Bit ....................................................................... 13 T0IF Bit ....................................................................... 13 Interrupt Sources .......................................................... 55, 65 A/D Conversion Complete .......................................... 50 Capture Complete (CCP)............................................ 34 Compare Complete (CCP).......................................... 35 Interrupt-on-Change (RB7:RB4 ) ................................ 21 RB0/INT Pin, External................................................. 66 TMR0 Overflow..................................................... 28, 66 TMR1 Overflow..................................................... 29, 30 TMR2 to PR2 Match ................................................... 32 TMR2 to PR2 Match (PWM) ................................. 31, 36 Interrupts, Context Saving During....................................... 66 Interrupts, Enable Bits A/D Converter Enable (ADIE Bit)................................ 14 CCP1 Enable (CCP1IE Bit) .................................. 14, 34 Global Interrupt Enable (GIE Bit) .......................... 13, 65 Interrupt-on-Change (RB7:RB4) Enable (RBIE Bit)... 13, 66 Peripheral Interrupt Enable (PEIE Bit) ........................ 13 RB0/INT Enable (INTE Bit) ......................................... 13 TMR0 Overflow Enable (T0IE Bit) .............................. 13 TMR1 Overflow Enable (TMR1IE Bit)......................... 14 TMR2 to PR2 Match Enable (TMR2IE Bit) ................. 14 Interrupts, Flag Bits A/D Converter Flag (ADIF Bit) .............................. 15, 50 CCP1 Flag (CCP1IF Bit)....................................... 15, 34 Interrupt-on-Change (RB7:RB4) Flag (RBIF Bit) .. 13, 66 RB0/INT Flag (INTF Bit) ............................................. 13 TMR0 Overflow Flag (T0IF Bit)............................. 13, 66 TMR1 Overflow Flag (TMR1IF Bit) ............................. 15 TMR2 to PR2 Match Flag (TMR2IF Bit)...................... 15 IORLW Instruction .............................................................. 79 IORWF Instruction .............................................................. 79 M Master Clear (MCLR) MCLR Reset, Normal Operation..................... 58, 62, 63 MCLR Reset, Sleep ........................................ 58, 62, 63 Memory Organization Data Memory ................................................................ 7 Program Memory .......................................................... 7 Migration from Base-Line to Mid-Range Devices ............. 114 MOVF Instruction................................................................ 79 MOVLW Instruction............................................................. 79 MOVWF Instruction ............................................................ 80 MPLAB ASM30 Assembler, Linker, Librarian ..................... 86 MPLAB ICD 2 In-Circuit Debugger ..................................... 87 MPLAB ICE 2000 High Performance Universal In-Circuit Emulator ...................................................... 87 MPLAB ICE 4000 High Performance Universal In-Circuit Emulator ...................................................... 87 Preliminary 2003 Microchip Technology Inc. PIC16F716 MPLAB Integrated Development Environment Software .... 85 MPLINK Object Linker/MPLIB Object Librarian .................. 86 N NOP Instruction................................................................... 80 O OPTION Instruction............................................................. 80 OPTION_REG Register ................................................ 10, 12 INTEDG Bit ................................................................. 12 PS2:PS0 Bits ........................................................ 12, 27 PSA Bit.................................................................. 12, 27 RBPU Bit..................................................................... 12 T0CS Bit................................................................ 12, 27 T0SE Bit................................................................ 12, 27 Oscillator Configuration................................................. 55, 57 HS ......................................................................... 57, 62 LP.......................................................................... 57, 62 RC................................................................... 57, 58, 62 Selection (FOSC1:FOSC0 Bits).................................. 56 XT ......................................................................... 57, 62 Oscillator, Timer1 .......................................................... 29, 30 Oscillator, WDT ................................................................... 67 P Packaging ......................................................................... 109 Paging, Program Memory ............................................... 7, 17 PCON Register ............................................................. 16, 62 BOR Bit ....................................................................... 16 POR Bit ....................................................................... 16 PICkit 1 FLASH Starter Kit .................................................. 89 PICSTART Plus Development Programmer ....................... 87 PIE1 Register ................................................................ 10, 14 ADIE Bit ...................................................................... 14 CCP1IE Bit.................................................................. 14 TMR1IE Bit.................................................................. 14 TMR2IE Bit.................................................................. 14 PIR1 Register.................................................................. 9, 15 ADIF Bit....................................................................... 15 CCP1IF Bit .................................................................. 15 TMR1IF Bit.................................................................. 15 TMR2IF Bit.................................................................. 15 Pointer, FSR ....................................................................... 18 POR. See Power-on Reset PORTA PORTA Register ..................................................... 9, 19 TRISA Register ..................................................... 10, 19 PORTB PORTB Register ..................................................... 9, 21 Pull-up Enable (RBPU Bit) .......................................... 12 RB0/INT Edge Select (INTEDG Bit)............................ 12 RB0/INT Pin, External................................................. 66 RB7:RB4 Interrupt-on-Change.................................... 66 RB7:RB4 Interrupt-on-Change Enable (RBIE Bit) ...................................................... 13, 66 RB7:RB4 Interrupt-on-Change Flag (RBIF Bit)........... 66 TRISB Register ..................................................... 10, 21 Postscaler, Timer2 Select (TOUTPS3:TOUTPS0 Bits) ............................. 31 Postscaler, WDT ................................................................. 27 Assignment (PSA Bit) ........................................... 12, 27 Rate Select (PS2:PS0 Bits) .................................. 12, 27 Switching Between Timer0 and WDT ......................... 28 Power-down Mode. See Sleep Power-on Reset (POR) ..................................... 55, 58, 62, 63 Oscillator Start-up Timer (OST) ............................ 55, 59 2003 Microchip Technology Inc. POR Status (POR Bit) ................................................ 16 Power Control (PCON) Register................................. 62 Power-down (PD Bit) ............................................ 11, 58 Power-on Reset Circuit, External ............................... 58 Power-up Timer (PWRT) ...................................... 55, 59 PWRT Enable (PWRTE Bit) ....................................... 56 Time-out (TO Bit).................................................. 11, 58 Time-out Sequence .................................................... 62 Time-out Sequence on Power-up............................... 64 Timing Diagram ........................................................ 101 Prescaler, Capture.............................................................. 34 Prescaler, Timer0 ............................................................... 27 Assignment (PSA Bit) ........................................... 12, 27 Rate Select (PS2:PS0 Bits) .................................. 12, 27 Switching Between Timer0 and WDT ......................... 28 Prescaler, Timer1 ............................................................... 30 Select (T1CKPS1:T1CKPS0 Bits) .............................. 29 Prescaler, Timer2 ............................................................... 37 Select (T2CKPS1:T2CKPS0 Bits) .............................. 31 PRO MATE II Universal Device Programmer ..................... 87 Program Counter PCL Register .......................................................... 9, 17 PCLATH Register ............................................. 9, 17, 66 Reset Conditions ........................................................ 62 Program Memory .................................................................. 7 Interrupt Vector............................................................. 7 Paging .................................................................... 7, 17 Program Memory Map.................................................. 7 Reset Vector................................................................. 7 Program Verification ........................................................... 69 PWM (CCP Module) ........................................................... 36 CCPR1H:CCPR1L Registers ..................................... 36 Duty Cycle .................................................................. 37 Example Frequencies/Resolutions ............................. 37 Output Diagram .......................................................... 36 Period ......................................................................... 36 Set-Up for PWM Operation......................................... 37 TMR2 to PR2 Match ............................................. 31, 36 TMR2 to PR2 Match Enable (TMR2IE Bit) ................. 14 TMR2 to PR2 Match Flag (TMR2IF Bit) ..................... 15 PWM (ECCP Module)......................................................... 38 Associated Registers.................................................. 48 Direction Change in Full-Bridge Output Mode............ 43 Effects of Reset .......................................................... 48 Full-Bridge Application Example................................. 43 Full-Bridge Mode ........................................................ 43 Half-Bridge Mode........................................................ 42 Half-Bridge Output Mode Applications Example ........ 42 Output Configurations................................................. 38 Output Relationships (Active High and Low) .............. 40 Output Relationships (Active-High and Low).............. 39 Output Relationships Diagram.............................. 39, 41 Programmable Dead-band Delay ............................... 45 Setup for Operation .................................................... 48 Shoot-through Current ................................................ 45 Start-up Considerations .............................................. 47 Q Q-Clock....................................................................... 37, 100 Preliminary DS41206A-page 119 PIC16F716 R RA3:RA0 ............................................................................. 19 RA4/T0CKI Pin.................................................................... 20 RAM. See Data Memory. RB0 Pin ............................................................................... 21 Register File .......................................................................... 8 Register File Map .................................................................. 8 Registers A/D ADCON0 .............................................................. 49 A/D ADCON1 .............................................................. 49 A/D ADRES........................................................... 49, 50 ADCON0 ADCS1:ADCS0 Bits .................................... 49 ADCON0 ADON Bit .................................................... 49 ADCON0 CHS2:CHS0 Bits ......................................... 49 ADCON0 GO/DONE Bit ........................................ 49, 50 ADCON1 PCFG2:PCFG0 Bits .................................... 50 CCP1CON CCP1M3:CCP1M0 Bits ............................ 33 CCP1CON CCP1X:CCP1Y Bits ................................. 33 Compare (CCP Module) CCPR1H:CCPR1L .............................................. 34 INTCON Register RBIF.................................................................... 21 PWM1CON (Enhanced PWM Configuration) ............. 46 T1CON Register T1CKPS1:T1CKPS0 Bits .................................... 29 T1OSCEN Bit...................................................... 29 T1SYNC Bit......................................................... 29 TMR1CS Bit ........................................................ 29 TMR1ON Bit........................................................ 29 T2CON Register T2CKPS1:T2CKPS0 Bits ................ 31 T2CON Register TMR2ON Bit .................................... 31 T2CON Register TOUTPS3:TOUTPS0 Bits ............... 31 Timer2 PR2 ..................................................................... 36 Timer2 PR2 Register .................................................. 31 Timer2 TMR2 Register................................................ 31 TMR1H Timer1 Register ............................................. 29 TMR1L Timer1 Register.............................................. 29 Reset............................................................................. 55, 58 Brown-out Reset (BOR). See Brown-out Reset (BOR) MCLR Reset. See MCLR Power-on Reset (POR). See Power-on Reset (POR) Reset Conditions for PCON Register.......................... 62 Reset Conditions for Program Counter ....................... 62 Reset Conditions for Status Register .......................... 62 Timing Diagram......................................................... 101 WDT Reset. See Watchdog Timer (WDT) RETFIE Instruction.............................................................. 80 RETLW Instruction .............................................................. 81 RETURN Instruction............................................................ 81 Revision History ................................................................ 113 RLF Instruction.................................................................... 81 RRF Instruction ................................................................... 82 S Shoot-through Current ........................................................ 45 Sleep ....................................................................... 55, 58, 68 Sleep Instruction ................................................................. 82 Software Simulator (MPLAB SIM)....................................... 86 Software Simulator (MPLAB SIM30)................................... 86 Special Event Trigger. See Compare Special Features of the CPU............................................... 55 Special Function Registers ................................................... 9 Speed, Operating .................................................................. 1 Stack ................................................................................... 17 DS41206A-page 120 Status Register ............................................................... 9, 66 C Bit ............................................................................ 11 DC Bit ......................................................................... 11 IRP Bit ........................................................................ 11 PD Bit ................................................................... 11, 58 RP1:RP0 Bits.............................................................. 11 TO Bit ................................................................... 11, 58 Z Bit ............................................................................ 11 SUBLW Instruction ............................................................. 82 SUBWF Instruction ............................................................. 83 SWAPF Instruction ............................................................. 83 T T1CON Register ................................................................... 9 T2CON Register ................................................................... 9 Timer0................................................................................. 27 Clock Source Edge Select (T0SE Bit) .................. 12, 27 Clock Source Select (T0CS Bit)............................ 12, 27 Overflow Enable (T0IE Bit) ......................................... 13 Overflow Flag (T0IF Bit)........................................ 13, 66 Overflow Interrupt ................................................. 28, 66 Prescaler. See Prescaler, Timer0 Timing Diagram ........................................................ 102 TMR0 Register.............................................................. 9 Timer1................................................................................. 29 Clock Source Select (TMR1CS Bit) ............................ 29 External Clock Input Sync (T1SYNC Bit).................... 29 Module On/Off (TMR1ON Bit)..................................... 29 Oscillator............................................................... 29, 30 Oscillator Enable (T1OSCEN Bit) ............................... 29 Overflow Enable (TMR1IE Bit).................................... 14 Overflow Flag (TMR1IF Bit) ........................................ 15 Overflow Interrupt ................................................. 29, 30 Prescaler. See Prescaler, Timer1 Special Event Trigger (CCP) ................................ 30, 35 T1CON Register ........................................................... 9 Timing Diagram ........................................................ 102 TMR1H Register ........................................................... 9 TMR1L Register............................................................ 9 Timer2 Postscaler. See Postscaler, Timer2 PR2 Register .............................................................. 10 Prescaler. See Prescaler, Timer2 T2CON Register ........................................................... 9 TMR2 Register.............................................................. 9 TMR2 to PR2 Match Enable (TMR2IE Bit) ................. 14 TMR2 to PR2 Match Flag (TMR2IF Bit)...................... 15 TMR2 to PR2 Match Interrupt......................... 31, 32, 36 Timing Diagrams Half-Bridge PWM Output ............................................ 42 PWM Auto-Shutdown (PRSEN = 0, Auto-Restart Disabled) ............................................................ 47 PWM Auto-Shutdown (PRSEN = 1, Auto-Restart Enabled) ............................................................. 47 PWM Direction Change .............................................. 44 PWM Direction Change at Near 100% Duty Cycle..... 44 Time-out Sequence on Power-up ............................... 64 Wake-up from Sleep via Interrupt ............................... 69 Timing Diagrams and Specifications .................................. 98 A/D Conversion......................................................... 105 Brown-out Reset (BOR)............................................ 101 Capture/Compare/PWM (CCP) ................................ 103 CLKOUT and I/O ...................................................... 100 External Clock............................................................. 98 Oscillator Start-up Timer (OST) ................................ 101 Power-up Timer (PWRT) .......................................... 101 Preliminary 2003 Microchip Technology Inc. PIC16F716 Reset......................................................................... 101 Timer0 and Timer1.................................................... 102 Watchdog Timer (WDT) ............................................ 101 TRIS Instruction .................................................................. 83 W W Register .......................................................................... 66 Wake-up from Sleep ..................................................... 55, 68 Interrupts............................................................... 62, 63 MCLR Reset ............................................................... 63 Timing Diagram........................................................... 69 WDT Reset ................................................................. 63 Watchdog Timer (WDT) ................................................ 55, 67 Enable (WDTE Bit)................................................ 56, 67 Postscaler. See Postscaler, WDT Programming Considerations ..................................... 67 RC Oscillator............................................................... 67 Time-out Period .......................................................... 67 Timing Diagram......................................................... 101 WDT Reset, Normal Operation ....................... 58, 62, 63 WDT Reset, Sleep .......................................... 58, 62, 63 WWW, On-Line Support ....................................................... 3 X XORLW Instruction ............................................................. 84 XORWF Instruction ............................................................. 84 2003 Microchip Technology Inc. Preliminary DS41206A-page 121 PIC16F716 NOTES: DS41206A-page 122 Preliminary 2003 Microchip Technology Inc. PIC16F716 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. PART NO. X /XX XXX Device Temperature Range Package Pattern Examples: a) b) Device PIC16F716, PIC16F716T, VDD range 2.0V to 5.5V Temperature Range I E = -40°C to +85°C = -40°C to +125°C Package SO P SS = = = Pattern QTP, SQTP, Code or Special Requirements (blank otherwise) PIC16F716 -I/P 301= Industrial temp., PDIP package, QTP pattern #301. PIC16F716 - E/SO = Extended temp, SOIC package (Industrial) (Extended) SOIC PDIP SSOP Note 1: T = in tape and reel SOIC and SSOP packages only. Sales and Support Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2003 Microchip Technology Inc. Preliminary DS41206A-page 123 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC Korea Corporate Office Australia 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 Atlanta Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 3780 Mansell Road, Suite 130 Alpharetta, GA 30022 Tel: 770-640-0034 Fax: 770-640-0307 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, IN 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles China - Beijing China - Chengdu Rm. 2401-2402, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599 China - Fuzhou Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 China - Hong Kong SAR Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 China - Shanghai Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 China - Shenzhen 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Rm. 1812, 18/F, Building A, United Plaza No. 5022 Binhe Road, Futian District Shenzhen 518033, China Tel: 86-755-82901380 Fax: 86-755-8295-1393 Phoenix China - Shunde 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-4338 Room 401, Hongjian Building No. 2 Fengxiangnan Road, Ronggui Town Shunde City, Guangdong 528303, China Tel: 86-765-8395507 Fax: 86-765-8395571 San Jose China - Qingdao 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Rm. B505A, Fullhope Plaza, No. 12 Hong Kong Central Rd. Qingdao 266071, China Tel: 86-532-5027355 Fax: 86-532-5027205 Toronto India 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Japan Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 DS41206A-page 124 Preliminary Singapore 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Kaohsiung Branch 30F - 1 No. 8 Min Chuan 2nd Road Kaohsiung 806, Taiwan Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan Taiwan Branch 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Austria Durisolstrasse 2 A-4600 Wels Austria Tel: 43-7242-2244-399 Fax: 43-7242-2244-393 Denmark Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45-4420-9895 Fax: 45-4420-9910 France Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Steinheilstrasse 10 D-85737 Ismaning, Germany Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Italy Via Quasimodo, 12 20025 Legnano (MI) Milan, Italy Tel: 39-0331-742611 Fax: 39-0331-466781 Netherlands P. A. De Biesbosch 14 NL-5152 SC Drunen, Netherlands Tel: 31-416-690399 Fax: 31-416-690340 United Kingdom 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44-118-921-5869 Fax: 44-118-921-5820 07/28/03 2003 Microchip Technology Inc.