PRODUCT INFORMATION 1A444 840nm Datacom, General Purpose VCSEL Laser Diode This Vertical Cavity SurfaceEmitting Laser is designed for Fibre Channel, Gigabit Ethernet, ATM and general applications. It operates in multiple transverse and single longitudinal mode, ensuring stable coupling of power and low noise. Optical and Electrical Characteristics PARAMETER Fiber-Coupled Power SYMBOL MIN. TYP. Optical Power Pfiber Po Slope Efficiency h 200 fc 2 (dPo/dIF) Bandwidth (3dBel ) Peak Wavelength lp Spectral Width (FWHM) MAX. 1.3 0.9 3.0 UNIT TEST CONDITION mW IF =12mA mW IF =12mA (Note 1) mW/A IF =12mA GHz IF =12mA 840 860 nm IF =12mA Dl 0.5 1 nm IF =12mA Forward Voltage (Fig.5) VF 1.9 2.2 V IF =12mA Threshold Current Ith 3.5 6 mA RIN -130 Relative Intensity Noise 830 1.7 (25° C Case Temperature) dB/Hz IF =12mA, f=1 GHz Note 1: Fiber: 50/125 Graded Index, NA=0.2 or 62.5/125 Graded Index, NA=0.275. Absolute Maximum Ratings PARAMETER Ø4.7 Ø1.5 SYMBOL LIMIT Storage Temperature Tstg -55 to +1258C Operating Temperature (derating: Fig.4) Top 0 to +708C Electrical Power Dissipation (derating: Fig.4) Ptot 35 mW IF 15 mA IFRM 25 mA Reverse Voltage VR 1.5 V Soldering Temperature (2mm from the case for 10 sec) Tsld 2608C 0.6 3.7 Continuous Forward Current (f<10 kHz) Peak Forward Current (duty cycle<50%, f>1 MHz) 14 0.4 CATHODE ANODE 2.5 5.4 BOTTOM VIEW All dimensions in mm CASE The chip is isolated from the case. TO-46 Package With Lens WARNING: Laser Radiation, avoid exposure to beam. Class 3B laser product, potential eye hazard. Warning labels in each box. Thermal Characteristics PARAMETER SYMBOL MIN. TYP. MAX. UNIT Thermal Resistance - Infinite Heat Sink Rthjc 400 8C/W Thermal Resistance - No Heat Sink Rthja 700 8C/W dl /dTj 0.06 nm/8C Optical Power - Variation 0 to 708C DP 60.7 dB Threshold Current - Variation 0 to 708C DIth 60.6 mA Temp. Coefficient -Wavelength 13457.11 1999-04-01 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 1A444 840nm VCSEL Laser Diode P o vs T FIGURE 1 RELATIVE THRESHOLD CURRENT 100 RELATIVE OPTICAL POWER Ith % 80 60 40 0 20 60 40 80 100 80 80 60 40 1008C 20 If vs Vf 60 1008C 80 50 10 40 INFINITE HEAT SINK 30 20 NO HEAT SINK 10 0 0 0 1 0 3V 2 20 Pf % 40 60 80 1008C OPERATING TEMPERATURE FORWARD VOLTAGE 6 vsFIGURE z Alignment Pf % 100 FIGURE 7 vs r Alignment 100 r r = opt. Øc = 50 µm z = opt. Øc = 50 µm RELATIVE FIBER-COUPLED POWER r 80 z 60 40 20 0 1.0 1.5 2.0 2.5 3.0 z - AXIAL DISPLACEMENT OF FIBER 3.5 mm 40 20 80 z 60 40 20 0 0 10 20 30 0 4 8 12 FORWARD CURRENT FIGURE 5 P el vs T mW MAX. ELECTRICAL POWER DISSIPATION FORWARD CURRENT 40 OPERATING TEMPERATURE 20 60 0 0 OPERATING TEMPERATURE mA FIGURE Po vs I3f % 100 20 20 RELATIVE FIBER-COUPLED POWER T vs 120 RELATIVE OPTICAL POWER % 120 40 r - RADIAL DISPLACEMENT OF FIBER 50 µm 16 20 mA Clip for SC-2A R 1.00 3.3000 5.6000 80,000 20.8200 0.5000 10,2500 10.3000 4.9500 0.5000 4.5000 5.0800 3.6450 Clip for Pigtail-3A 10.70 0.50 10.30 10.25 4.95 0.50 4.50 0.85 5.08 3.65 PRODUCT INFORMATION ST-2A Emitter or Detector in ST ® Package Package Mitel emitters and detectors can be provided in this low-profile ST ® package. The device is electrically isolated from the ST ® receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature Tstg , Top -40 to +858C ST-2A (Note 1) Note 1: Temperature range can be extended to -55° to +125°C on request. Thermal Characteristics PARAMETER SYMBOL Thermal Resistance - Infinite Heat Sink (Note 2) Thermal Resistance - No Heat Sink (Note 2) Thermal Resistance - On PC Board MIN. TYP. MAX. UNIT Rthcc 40 8C/W Rthca 200 8C/W Rthca 8C/W 80 (Note 2) Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance. 2-56 UNC - 2B 3/8"-32 UNEF max.0.5 0.006 Ø2.502 +0.01 0 9.5 SLOT SIDE MARKING SIDE 12.7 FIBER END Ø2.5 +0 -0.004 7.6 5.4 min.12 All Dimensions in mm 7.89 3.9 20.1 MATING FERRULE* (not included) *The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in ST-2A Housing (ST is a registered trademark of AT&T) 103326 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION SMA-2A Emitter or Detector in SMA Package Package Mitel emitters and detectors can be provided in this low-profile SMA package. The device is electrically isolated from the SMA receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Tstg , Top -40 to +858C Operating & Storage Temperature SMA-2A (Note 1) Note 1: Temperature range can be extended to -55° to +125°C on request. Thermal Characteristics PARAMETER SYMBOL Thermal Resistance - Infinite Heat Sink (Note 2) Thermal Resistance - No Heat Sink (Note 2) Thermal Resistance - On PC Board MIN. MAX. UNIT Rthcc 40 8C/W Rthca 200 8C/W Rthca TYP. 80 8C/W (Note 2) Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance. 2-56 UNC - 2B +0.01 0 1/4"-36UNS 9.5 12.7 Ø3.176 FIBER END 0.006 5.7 min.12 All Dimensions in mm 9.8 ± 0.03 +0 -0.004 3.9 7.2 Ø3.174 MARKING SIDE max.0.5 15.2 MATING FERRULE* (not included) *The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in SMA-2A Housing 103325 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION SC-2A Emitter or Detector in SC Package Package Mitel emitters and detectors can be provided in this low-profile SC package. The device is electrically isolated from the SC receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber.. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature Tstg , Top -40 to +858C Thermal Characteristics PARAMETER SYMBOL Thermal Resistance - Infinite Heat Sink (Note 1) Thermal Resistance - No Heat Sink (Note 1) Thermal Resistance - On PC Board MAX. UNIT Rthcc 40 8C/W Rthca 200 8C/W Rthca MIN. TYP. 8C/W 125 (Note 1) Note 1: Add Rthjc for emitter or detector to estimate the total thermal resistance. 2.5 1. 4 12 x4 MARKING / SLOT SIDE 0.006 13 Ø7.5 18 22 Ø2.3 FIBER END Ø2.5 +0 -0.004 7.95 MATING FERRULE* (not included) 8.9 All Dimensions in mm min. 12 18 * The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in SC-2A Housing 105967 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION Pigtail-3A Emitter or Detector in Pigtail Package Package Mitel emitters and detectors can be provided in this pigtail package with a wide selection of fiber types. The device is electrically isolated from the pigtail receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. A special design maximizes the return loss for detectors in this package. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature (Note 1 & 2) Tstg , Top - 40 to +858C Note 1: Temperature range can be extended to -55/+1258C on request. Note 2: Temperature range may be limited by the specification of the fiber. Thermal Characteristics PARAMETER SYMBOL Thermal Resistance - Infinite Heat Sink (Note 3) Thermal Resistance - No Heat Sink (Note 3) Thermal Resistance - On PC-Board (Note 3) MIN. MAX. UNIT Rthcc 25 8C/W Rthca 250 8C/W Rthca TYP. 8C/W 120 Note 3: Add Rthjc for LED to estimate the total thermal resistance. Optical Characteristics PARAMETER Return Loss 10/125mm fiber (PIN only) SYMBOL MIN. TYP. RL 40 55 MAX. UNIT dB Ø6 MARKING Ø6.00 min.12 13 All Dimensions in mm Mechanical Outline of Diode in PIGTAIL-3A Housing 105429 1997-07-03 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 PRODUCT INFORMATION FC-2A Emitter or Detector in FC Package Package Mitel emitters and detectors can be provided in this low-profile FC package. The device is electrically isolated from the FC receptacle to facilitate electrical connection. And optimum fiber-coupled power or responsivity is ensured by active alignment against the fiber. Absolute Maximum Ratings PARAMETER SYMBOL LIMIT Operating & Storage Temperature Tstg , Top -40 to +858C FC-2A (Note 1) Note 1: Temperature range can be extended to -55° to +125°C on request. Thermal Characteristics PARAMETER SYMBOL Thermal Resistance - Infinite Heat Sink (Note 2) Thermal Resistance - No Heat Sink (Note 2) Thermal Resistance - On PC Board MIN. MAX. UNIT Rthcc 40 8C/W Rthca 200 8C/W Rthca TYP. 8C/W 80 (Note 2) Note 2: Add Rthjc for emitter or detector to estimate the total thermal resistance. min.12 5.6 2.0 5.50 Ø 2.5 0.006 13.4 MARKING/ SLOT SIDE 08 19 Ø 2.2 FIBER END Ø2.5 M8x0.75 Thread max. 0.5 9.2 All Dimensions in mm +0 -0.004 7.95 MATING FERRULE* (not included) * The fiber-coupled power/responsivity is guaranteed to meet the LED/PIN data sheet - provided a ferrule meeting this specification is used. Mechanical Outline of Diode in FC-2A Housing 105515 1994-09-20 Europe: Tel (46) 8 58 02 45 00 Fax (46) 8 58 02 01 10 Tel (44) 1291 436180 Fax (44) 1291 436771 America: Tel 1-800-96MITEL Fax (613) 592-6909 Asia: Tel (65) 293 5312 Fax (65) 293 8527 http://www.mitelsemi.com World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s conditions of sale which are available on request. M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE