HIGH CMR, 10 Mbps TOTEM POLE OUTPUT TYPE 5-PIN SOP PHOTOCOUPLER PS9715 FEATURES DESCRIPTION • HIGH COMMON MODE TRANSIENT IMMUNITY CMH, CML = ±20 kV/µs TYP PS9715 is an optically coupled high-speed, totem pole output isolator containing a GaAIAs LED on the light emitting side (input side) and a photodiode and a signal processing circuit on the light receiving side (output side) on one chip. • SMALL AND THIN PACKAGE 5-pin SOP • HIGH SPEED 10 Mbps APPLICATIONS • PULSE WIDTH DISTORTION |tPHL – tPLH| = 7 ns TYP • LAN/FA • HIGH ISOLATION VOLTAGE BV = 2500 Vr.m.s. • PDP • MEASUREMENT EQUIPMENT • TOTEM POLE OUTPUT No pull-up resistor required PS9715 6 5 4 • AVAILABLE IN TAPE AND REEL PS9715-F3, F4: 3500 pcs/reel 1 3 ELECTRICAL CHARACTERISTICS (TA = 0 to +85°C, Unless otherwise specified) PART NUMBER Coupled Detector Diode SYMBOL PS9715 PARAMETERS UNITS MIN TYP1 MAX 1.4 1.65 1.9 VF Forward Voltage, IF = 10 mA, TA = 25°C V IR Reverse Current, VR = 3 V, TA = 25°C µA Ct Capacitance, V = 0, f = 1 MHz, TA = 25°C pF 30 10 IOH High Level Output Current2 Vcc = VO = 5.5 V, VF = 0.8 V µA 0.003 VOH High Level Output Voltage Vcc = 4.5 V, IF = 250 µA, IOH = -2 mA V VOL Low Level Output Voltage Vcc = 4.5 V, VF = 0.8 V, IOL = 8 mA V 0.25 0.6 ICCH High Level Supply Current, VCC = 5.5 V, IF = 0 mA mA 12 17 18 2.4 3.0 ICCL Low Level Supply Current, VCC = 5.5 V, IF = 10 mA mA 13 IOSH High Level Output Short Circuit Current, VCC = 5.5 V, VO = GND IF = 0 mA, 10 ms or less mA -26 IOSL Low Level Output Short Circuit Current, VCC = 5.5 V, VO = GND IF = 8 mA, 10 ms or less mA 34 IFHL Threshhold Input Current, High → Low, VCC = 5 V mA 2.3 RI-O Isolation Resistance, VI-O = 1 k VDC, RH = 40 to 60%, TA = 25°C Ω CI-O Isolation Capacitance, V = 0, f = 1 MHz, TA = 25°C pF 1 TA = 25°C 200 5 6 1011 0.4 tPHL Propagation Delay Time , High → Low VCC = 5 V, IF = 7.5 mA TA = 25°C ns 15 10 33 65 85 tPLH Propagation Delay Time1, Low → High VCC = 5 V, IF = 7.5 mA TA = 25°C ns 15 10 40 65 85 Continued on next page California Eastern Laboratories PS9715 ELECTRICAL CHARACTERISTICS (TA = 0 to +85°C, Unless otherwise specified), Continued PART NUMBER SYMBOL Coupled | tPHL – tPLH | PS9715 PARAMETERS UNITS Pulse Width Distortion, (PWD)3, VCC = 5 V, IF = 7.5 mA MIN ns Output4, TYP MAX 7 50 CMH Common Mode Transient Immunity at High Level VCC = 5 V, TA = 25°C, IF = 0 mA, VO (MIN) = 2 V, VCM = 1 kV kV/µs 10 20 CML Common Mode Transient Immunity at Low Level Output4, VCC = 5 V, TA = 25°C, IF = 7.5 mA, VO (MAX) = 0.8 V, VCM = 1 kV kV/µs 10 20 Notes: 1. Typical values at TA = 25°C. 2. Because a high level output current (IOH) of 300 µA or more may be output when the temperature is 0°C or less and when VCC is around 3 to 4 V, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using the device. 3. Test Circuit for Propagation delay time VCC = 5 V VCC = 5 V IF (ON) Pulse input (IF) Input VO (monitor) 50% IF (ON) 1.3 kΩ (PW = 500 ns, Duty cycle = 1/2) 0.1 µ F VOH Input (monitor) CL = 30 pF Output 2.5 kΩ 47 Ω tPHL 1.5 V VOL tPLH CL includes probe and stray wiring capacitance. 4.Test Circuit for common mode transient immunity SW IF 1 kV VCM 90% VCC = 5 V 10% 0.1 µ F VO (Monitor) CL = 15 pF 0V tr tf VO (IF = 0 mA) VOH 2V VCM 0.8 V VOL VO (IF = 7.5 mA) CL includes probe and stray wiring capacitance. USAGE CAUTIONS 1. This device is ESD sensitive. 2. Bypass capacitor of more than 0.1 µF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capactor is no more than 10 mm. ABSOLUTE MAXIMUM RATINGS1 (TA = 25°C) SYMBOLS Diode IF VR Detector VCC VO IOH IOL PC Coupled BV TOP TSTG PARAMETERS UNITS RATINGS Forward Current Reverse Voltage mA V 30 5 Supply Voltage Output Voltage High level Output Current2 Low level Output Current2 Power Dissipation2,3 V V mA mA mW 7 7 -5 13 130 Vr.m.s. °C °C 2500 -40 to +85 -55 to +125 Isolation Voltage4 Operating Temperature Storage Temperature RECOMMENDED OPERATING CONDITIONS Notes: 1. Operation in excess of any one of these parameters may result in permanent damage. 2. TA = -40 to +85°C, Applies to output pin Vo and power supply pin VCC. PART NUMBER SYMBOLS IFH IFL VCC N TA PARAMETERS High Level Input Current Low Level Input Current Supply Voltage TTL(loads) Operating Temperature PS9715 UNITS MIN TYP MAX mA 7.5 12.5 µA 0 250 V 4.5 5.0 5.5 3 °C 0 +85 4. AC voltage for 1 minute at TA = 25 °C, RH = 60% between input and output. PS9715 TYPICAL PERFORMANCE CURVES (TA = 25°C) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE 150 Detector Power Dissipation, PC (mW Maximum Forward Current, IF (mA) 40 30 20 10 0 20 40 80 85 60 100 100 50 0 Ambient Temperature, TA (°C) High Level Supply Current, ICCH (mA) LowLevel Supply Current, ICCL (mA) Forward Curren, IF (mA) 80 85 100 20 10 TA = +85˚C +50˚C +25˚C 1 0˚C –25˚C 0.1 1.2 1.4 1.6 1.8 2.0 2.2 VCC = 5.5 V 16 ICCL (IF = 10 mA) 12 ICCH (IF = 0 mA) 8 4 0 –50 2.4 Forward Voltage, VF (V) Propagation Delay Time,tPHL, tPLH (ns) Pulse Width Distortion, |tPHL—tPLH| (ns) VCC = 4.5 V, VF = 0.8 V, IOH = 2.0 mA 4 3 2 1 0 25 50 0 25 50 75 100 PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE 5 –25 –25 Ambient Temperature, TA (°C) HIGH LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE High Level Output Voltage, VOH (V) 60 SUPPLY CURRENT vs. AMBIENT TEMPERATURE 100 0 –50 40 Ambient Temperature, TA (°C) FORWARD CURRENT vs. FORWARD VOLTAGE 0.01 1.0 20 75 Ambient Temperature, TA (°C) 100 50 tPLH 40 tPHL 30 20 10 PWD 0 –50 –25 0 25 50 75 Ambient Temperature, TA (°C) 100 PS9715 TYPICAL PERFORMANCE CURVES (TA = 25°C) LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE 5 VCC = 4.5 V, IF = 7.5 mA, IOL = 8.0 mA Low Level Output Voltage, VOL (V) Low Level Output Voltage, VOL (V) 0.5 0.4 0.3 0.2 0.1 0 –50 VCC = 5.0 V 4 3 2 1 0 –25 0 25 50 75 –50 100 50 75 100 5 0.5 VCC = 4.5 V, IF = 5.0 mA High Level Output Voltage, VOH (V) Low Level Output Voltage, VOL (V) 25 HIGHLEVEL OUTPUT VOLTAGE vs. HIGHLEVEL OUTPUT CURRENT LOW LEVEL OUTPUT VOLTAGE vs. LOW LEVEL OUTPUT CURRENT 0.4 TA = 85˚C 0˚C 25˚C 0.3 0.2 0.1 0 2.5 5 7.5 12.5 10 13 VCC = 4.5 V, VF = 0.8 V TA = 85˚C 25˚C 4 0˚C 3 2 1 0 –1 –2 –3 –4 –5 High Level OututCurrent, IOH (mA) Low Level OututCurrent, IOL (mA) PROPAGATION DELAY TIME, PULSE WIDTH DISTORTION vs. FORWARD CURRENT HIGH LEVEL OUTPUT VOLTAGE vs. HIGH LEVEL OUTPUT CURRENT 60 VCC = 4.5 V, IF = 250 µA TA = 85˚C 25˚C 3 0˚C 2 1 –5 –10 –15 –20 –25 –30 High Level OututCurrent, IOH (mA) –35 Propagation Delay Time,tPHL, tPLH (ns) Pulse Width Distortion, |tPHL—tPLH| (ns) 4 High Level Output Voltage, VOH (V) 0 Ambient Temperature, TA (°C) Ambient Temperature, TA (°C) 0 –25 TA = 25˚C, VCC = 5 V tPHL 40 tPLH 20 PWD 0 5 10 15 20 25 Forward Current, IF (mA) 30 PS9715 OUTLINE DIMENSIONS (Units in mm) MARKING PS9715 4.0±0.5 TOP VIEW 5 4 No. 1 pin Mark 9715 N003 3 Assembly Lot 1. Anode 2. Cathode 3. GND 4. VO 5. VCC 1 2 N 7.0±0.3 Week Assembled Year Assembled (Last 1 Digit) Rank Code 2.1±0.2 0.15 +0.10 –0.05 4.4 0.5±0.3 0.1±0.1 1.27 0.4 +0.10 –0.05 0 03 0.25 M TAPING SPECIFICATIONS (Units in mm) TAPE OUTLINE AND DIMENSIONS REEL OUTLINE AND DIMENSIONS 2.0±0.5 1.5 ± 0.1 4.0±0.1 2.9 MAX +0.1 2.0±0.05 1.5 -0 1.75±0.1 2.0±0.5 7.4±0.1 R1.0 φ100±1.0 12±0.2 φ 330±2.0 5.5±0.05 φ13.0±0.2 φ13.0±0.2 φ21.0±0.8 13.5±1.0 2.4±0.1 1.55±0.1 17.5±1.0 4.6±0.1 0.3 8±0.1 11.9 to 15.4 Outer edge of flange Packing : 3500 pcs/reel TAPE DIRECTION PS9715-F3 PS9715-F4 PS9715 RECOMMENDED SOLDERING CONDITIONS Package Surface Temperature T (˚C) (1) Infrared reflow soldering • Peak reflow temperature • Time of temperature higher than 210 ºC • Number of reflows • Flux 235˚C or below (package surface temperature) 30 seconds or less Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt % is recommended.) (heating) to 10 s 235˚C (peak temperature) 210˚C to 30 s 100 to 160°C 60 to 120 s s (preheating) Time (s) (3) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. EXCLUSIVE NORTH AMERICAN AGENT FOR NEC RF, MICROWAVE & OPTOELECTRONIC SEMICONDUCTORS CALIFORNIA EASTERN LABORATORIES • Headquarters • 4590 Patrick Henry Drive • Santa Clara, CA 95054-1817 • (408) 988-3500 • Telex 34-6393 • FAX (408) 988-0279 Internet: http://WWW.CEL.COM DATA SUBJECT TO CHANGE WITHOUT NOTICE 06/26/2002