PERICOM PI5A100Q

PI5A100
Precision, Wide-Bandwidth
Quad SPDT Analog Switch
Features
Description
• Single Supply Operation (+2V to +6V)
The PI5A100 is an improved Quad Single-pole double-throw
(4SPDT) CMOS analog switch designed to operate with a single
+2V to +6V power supply. The EN pin may be used to place all
switches in a high-impedance state. This high precision device
is ideal for low-distortion audio, video, and data switching and
routing.
• Rail-to-Rail Analog Signal Dynamic Range
• Low On-Resistance (6Ω typ with 5V supply) Minimizes
Distortion and Error Voltages
• On-Resistance Matching Between Channels, 0.4Ω Typ.
• On-Resistance Flatness, <2Ω Typ.
Each switch conducts current equally well in either direction
when on. In the off state each switch blocks voltages up to the
power-supply rails.
• Low Charge Injection Reduces Glitch Errors, Q = 6pC Typ.
• Replaces Mechanical Relays
The PI5A100 is fully specified with +5V, and +3.3V supplies. With
+5V, it guarantees less than 10Ω On-Resistance. On-Resistance
matching between channels is within 2Ω. On-Resistance flatness
is less than 4Ω over the specified range. The PI5A100 guarantees
fast switching speeds (tON < 12ns).
• High Speed. tON, 8ns Typ.
• Low Crosstalk: -100dB @ 10 MHz
• Low Off-Isolation: -57dB @ 10 MHz
• Wide -3dB Bandwidth: 230 MHz
The PI5A100 is available in the narrow-body SOIC and QSOP
packages for operation over the industrial (-40°C to +85°C) temperature range.
• High-Current Channel Capability: >100mA
• TTL/CMOS Logic Compatible
• Low Power Consumption (0.5µW typ.)
• Packaging (Pb-free & Green Available):
-16-pin QSOP (Q)
-16-pin SOIC (W)
Block Diagram, Pin Configuration
Applications
• Audio, Video Switching and Routing
• LAN Switches
IN 1
• Telecommunication Systems
• Battery-Powered Systems
Truth Table
EN
0
0
1
IN
0
1
X
ON Switch
NC1, NC2, NC3, NC4
NO1, NO2, NO3, NO4
None. Disabled
Decoder
16 VCC
NC1 2
15 EN
NO1 3
14 NC4
COM1 4
13 NO4
NC2 5
12 COM4
NO2 6
11 NC3
COM2 7
10 NO3
GND 8
9
COM3
Notes:
1. Switches shown for logic "0" input.
2. NC = Normally Closed; NO = Normally Open
1
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Absolute Maximum Ratings
Thermal Information
Voltages Referenced to Gnd
VCC ........................................................................-0.5V to +7V
Continuous Power Dissipation
Narrow SOIC & QSOP
(derate 8.7mW/ºC above +70ºC) . . . . . . . . . . . . . . . . . 650mW
VIN, VCOM, VNC, VNO (1) ..............................-0.5V to VCC +2V
..................................................or 30mA, whichever occurs first
Current (any terminal except COM, NO, NC).................. 30mA
Current, COM, NO, NC
(pulsed at 1ms, 10% duty cycle) ..................................... 120mA
Storage Temperature . . . . . . . . . . . . . . . . . . . . -65ºC to +150ºC
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . +300ºC
Notes:
1. Signals on NC, NO, COM, or IN exceeding VCC or GND are clamped by internal diodes. Limit forward diode current to 30mA.
2. Caution: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress
only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this speci fication
is not implied.
Electrical Specifications - Single +5V Supply (VCC = +5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V)
Parameter
Symbol
TestConditions
Temp.
Min.(1)
Full
0
Typ.(2)
Max.(1)
Units
VCC
V
Analog Switch
Analog Switch Range(1)
VANALOG
On-Resistance
RON
On-Resistance Match Between Channels(6)
∆RON
On-Resistance Flatness(5)
RFLAT(ON)
VCC = 5V, ICOM = -30mA,
VNO or VNC = +2.5V
NO or NC OFF Leakage(6)
INO(OFF) or
INC(OFF)
VCC = 5.5C, ICOM = 0V,
VNO or VNC = 4.5V
COM OFF Leakage
Current(6)
ICOM(OFF)
VCC = 5.5V, ICOM = 4.5V,
VNO or VNC = ± 4.5V
COM ON Leakage
Current(6)
ICOM(ON)
VCC = 5.5V, ICOM = 4.5V,
VNO or VNC = ± 4.5V
25
VCC = 4.5V, ICOM = -30mA,
VNO or VNC = +2.5V
8
Full
12
25
0.8
Full
2
2
Full
3
0.07
-80
25
80
0.01
-80
25
Full
Ω
4
25
Full
2
4
25
Full
10
80
nA
0.016
-80
80
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Electrical Specifications - Single +5V Supply (VCC = +5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V) CONTINUED
Parameter
Symbol
TestConditions
Temp.
Min.(1)
Full
2
Typ.(2)
Max.(1)
Units
Logic Input
Input High Voltage
VIH
Guaranteed logic High Level
Input Low Voltage
VIL
Guaranteed logic Low Level
Input Current with Input Voltage
High
IINH
VIN = 2.4V, all others = 0.8V
Input Current with Input Voltage
Low
IINL
VIN = 0.8V, all others = 2.4V
0.8
Full
-1
0.005
V
1
µA
-1
0.005
1
8
15
Dynamic
Turn-On Time
25
tON
VCC = 5V, See Figure 1
Full
20
25
3.5
Turn-Off Time
tOFF
Charge Injection(3)
Q
CL = 1nF, VGEN = 0V,
RGEN = 0Ω, See Figure 2
Off Isolations
OIRR
RL = 50Ω, CL = 5pF,
f = 10MHz, See Figure 3
-57
Crosstalk(8)
XTALK
RL = 50Ω, CL = 5pF,
f = 10MHz, See Figure 4
-100
NC or NO Capacitance
C(OFF)
f=1kHz, See Figure 5
COM OFF Capacitance
CCOM(OFF)
COM ON Capacitance
CCOM(ON)
f = 1kHz, See Figure 6
-3db Bandwidth
BW
RL = 50Ω See Figure 7
Distortion
D
RL = 10kΩ
7
Full
10
25
10
ns
pC
dB
8
14
pF
18
Full
230
MHz
0.2
%
Supply
Power-Supply
VCC
Postitive Supply Current
ICC
Full
VCC = 5.5V, VIN = 0V or VCC,
all channels on or off
2
6
V
1
µA
Notes:
1. The algebraic convention, where the most negative value is a minimum and the most positive is a maximum, is used in this data sheet.
2. Typical values are for DESIGN AID ONLY, not guaranteed or subject to production testing.
3. Guaranteed by design
4. ΔRΟΝ = RΟΝ max - RΟΝ min
5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured.
6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC.
7. Off Isolation = 20log10 [ VCOM / (VNO or VNC) ]. See figure 3.
8. Between any two switches. See figure 4.-
3
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Electrical Specifications - Single +3.3V Supply (VCC = +5V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V)
Parameter
Symbol
TestConditions
Temp.
Min.(1)
Typ.(2)
Max.(1)
Units
VCC
V
Analog Switch
Analog Switch Range(1)
0
On-Resistance
RON
On-Resistance Match Between Channels(6)
∆RON
On-Resistance Flatness(5)
RFLAT(ON)
25
VCC = 4.5V, ICOM = -30mA,
VNO or VNC = +2.5V
12
18
Full
25
5
Ω
Full
VCC = 5V, ICOM = -30mA,
VNO or VNC = +2.5V
25
2
Full
4
5
Dynamic
Turn-On Time
25
tON
VCC = 5V, See Figure 1
Turn-Off Time
tOFF
Charge Injection(3)
Q
CL = 1nF, VGEN = 0V,
RGEN = 0Ω, See Figure 2
ICC
VCC = 3.6V, VIN = 0V or VCC,
all channels on or off
14
Full
25
40
4.5
Full
25
25
12
ns
20
5
10
pC
1
µA
Supply
Postitive Supply Current
4
Full
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Typical Operating Characteristics (TA=+25ºC, unless otherwise noted)
RON vs. VCOM
RON vs. VCOM and Temperature
16
40
A: TA = 90°C
B: TA = 25°C
C: TA = -40°C
VCC = +5V
Vcc = +2V
12
RON
RON
30
20
+3.3V
10
A
8
B
4
+5V
+7V
0
1
2
3
5
4
VCOM (V)
6
Leakage Currents vs. Analog Voltage
2
3
Leakage Current
10nA
16
1nA
5
4
vs. Temperature
VCC = +5V
)
or IB(ON
)
ON
M(
I CO
100pA
8
IA(ON) or IB(ON)
Leakage
Leakage (pA)
1
0
7
20
IA(ON)
C
0
F)
OF
M(
O
IC
10pA
1pA
-8
0.1pA
-16
0
1
2
3
4
5
0.01pA
-40
Temperature (˚C)
Charge Injection
vs. Analog Voltage
40
80
Temperature (˚C)
Crosstalk and Off-Isolation vs. Frequency
-100
15
Crosstalk
-80
10
-60
VCC = 5V
(dB)
Q-Charge Injection (pC)
0
5
Off Isolation
-40
VCC = 3.3V
0
-20
VCC = 5V
-5
0
1
0
1
2
3
4
5
2
4
6
8 10
20
40
60 80 100
200
Frequency (MHz)
VCOM (V)
5
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Insertion Loss vs. Frequency
Input Switching Threshold
0
vs. Supply Voltage
5
-1
4
-3
-3dB Point
-4
3
VIN, (V)
Insertion Loss (dB)
-2
-5
-6
2
-7
VCC = +5V
R L= 50!
-8
-9
1
0
-10
1
3
30
6 10
Frequency (MHz)
300
60 100
RON vs. VCOM and Single Supply
VCC (V)
7
6
Switching Times vs. Temperature
20
15
tON tOFF (ns)
t ON, t OFF (ns)
5
4
20
25
15
10
t ON,
5
0
3
10
tON
5
tOFF
t OFF
0
3
3.5
4
4.5
5
5.5
V CC (V)
6.5
6
7
-40
0
40
80
120
Temperature (°C)
Supply Current vs. Temperature
10
VCC = +5V
ICC (nA)
1
0.1
0.01
0.001
-40
0
40
80
Temperature (°C)
6
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Test Circuits/Timing Diagrams
+5V
Logic +3V
Input
0V
Vcc
Switch
Input +3V*
NO
or NC
COM
RL
100Ohm
IN
Logic
Input
VOUT
tr <20ns
tf <20ns
50%
tOFF
CL
15pF
Switch
Output
GND
VOUT
0V
90%
90%
tON
LOGIC INPUT WAVEFORMS INVERTED FOR
SWITCHES THAT HAVE OPPOSITE LOGIC
* 1.5V FOR 3.3V SUPPLY
CL INCLUDES FIXTURE AND STRAY CAPACITANCE
RL
VOUT = VNO
RL + RON
(
)
Figure 1. Switching Time
+5V
RGEN
VGEN
V+
NO or
NC
COM
.1µF
∆VOUT
VOUT
VOUT
IN
CL
OFF
1nF
IN
Logic
Input
GND
IN
OFF
ON
ON
OFF
OFF
Q = (∆VOUT)(CL)
Figure 2. Charge Injection
7
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Test Circuits/Timing Diagrams (continued)
+5V
10nF
10nF
COM
Signal
Generator 0dBm
V+
50Ohm
IN
COM
Analyzer
0V or
2.4V
NC
or NO
+5V
10nF
IN
NC
or NO
Capacitance
Meter
0V or
2.4V
f = 1kHz
EN
NC
or NO
+5V
COM
V+
IN
NC
or NO
GND
Figure 5. Channel-Off Capacitance
10nF
10Ohm
V+
GND
NC
N02
EN
Figure 4. Crosstalk
Figure 3. Off Isolation
f = 1MHz
COM2
50Ohm
50Ohm
COM
50Ohm
N01
GND
EN
10nF
V+
IN
COM
GND
Capacitance
Meter
COM1
0V or
2.4V
Analyzer
+5V
0V or
2.4V
EN
Figure 6. Channel-On Capacitance
+5V
VCC
COM
Vo
RL
10Ohm
Rg = 50Ohm
GND
EN
Figure 7. Bandwidth
8
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Applications Information
Positive Supply
Overvoltage Protection
Proper power-supply sequencing is recommended for all CMOS
devices. Do not exceed the absolute maximum ratings, because
stresses beyond the listed ratings may cause permanent damage
to the devices. Always sequence V+ on first, followed by V-, and
then logic inputs. If power-supply sequencing is not possible, add
two small signal diodes or two current limiting resistors in series
with the supply pins for overvoltage protection (Figure 8). Adding
diodes reduces the analog signal range, but low switch resistance
and low leakage characteristics are unaffected.
V+
COM
NO
Vg
RGB Switch
Figure 9 illustrates a simple low cost RGB switch. The RGB to-Composite Decoder produces either NTSC or S-VHS video
from an RGB source. Asingle PI5A100 selects one of the two
video sources to produce either SVHS, Composite or RGB video
outputs. The low insertion loss of the PI5A100 eliminates the need
for expensive input/output buffers.
V-
Figure 8: Overvoltage protection is accomplished using two external blocking diodes or two current limiting resistors.
SVGA
R-G-B
RGB to
Composite
Encoder
Y
Composite
C
Sync
4
S-Video
Connector
+5V
VGA
Connect or
R
G
R or Luma 0.7V
B
G or Composite 0.714V
Sync
PI5A100
B or Chroma 0.28V
H-Sync-0.3V
Select
Composite
Connector
Figure 9: The single PI5A100 is used to select SVHS, VGA or Composite video outputs.
9
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Applications
Audio Muting Function
Figure 8 shows the PI5A100 in an audio card muting application.
The original problem was one of excessive popping/clicking noise
appearing when connecting disconnecting external loads, and at
power on/off. The PI5A100 performs a muting function by grounding
the outputs at power on/off and during the transition time. The
32Ω headset impedance demands a very low and very flat switchon resistance to reduce THD and signal loss.
Paralleling two sections of the PI5A100 produces a Ron of 2.5Ω
with an unsurpassed ±0.5Ω flatness.
To handle AC signals it was necessary to power the device with
±3V provided by two Zener diodes: Z1 and Z2. The select and
Enable control signals are shifted by using twpo 2.5V Zener diodes
Z3,Z4 and pull down resistors connected to -3V.
10kΩ
Stereo Audio
Output
Stereo Audio
Input
From DAC
J1
Select
Enable
J2
Z3
-3V
GND
-5V
+5V
Vcc
2.5V
32!
Z1
Z2
Z4
Z1/Z2 - Dual SMT 3.0V Zener
2.5V
22k!
-3V
Figure 10: The PI5A100 momentarily mutes the stereo outputs by connecting them to ground during transition times.
10
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Packaging Mechanical: 16-Pin QSOP (Q)
16
.008
0.20
MIN.
.150
.157
3.81
3.99
Guage Plane
.010
0.254
1
0˚-6˚
.016
.035
0.41
0.89
Detail A
.189
.197
4.80
5.00
.041
1.04
REF
.015 x 45° 0.38
.008
0.203 REF
.053 1.35
.069 1.75
Detail A
.008
.012
0.203
0.305
.007
.010
0.178
0.254
0.41 .016
1.27 .050
SEATING
PLANE
.025
BSC
0.635
.008
.013
0.20
0.33
.228
.244
5.79
6.19
.004 0.101
.010 0.254
X.XX DENOTES DIMENSIONS IN MILLIMETERS
X.XX
Packaging Mechanical: 16-Pin SOIC (W)
16
.149
.157
3.78
3.99
.0099
.0196
0.25
x 45˚
0.50
1
.0075
.0098
0-8˚
.386
.393
9.80
10.00
0.41
1.27
.053
.068
.0155
.0260
0.393
0.660
REF
1.35
1.75
SEATING PLANE
.050
BSC
1.27
.013
.020
0.330
0.508
0.19
0.25
.016
.050
.2284
.2440
5.80
6.20
.0040 0.10
.0098 0.25
X.XX DENOTES DIMENSIONS
X.XX IN MILLIMETERS
11
PS7012H
08/30/04
PI5A100
Precision, Wide-Bandwidth, Quad SPDT Analog Switch
Ordering Information
Ordering Code
Package Code
Package Description
PI5A100W
W
16-pin SOIC
PI5A100Q
Q
16-pin QSOP
PI5A100QE
Q
Pb-free & Green, 16-pin QSOP
Notes:
1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
2,. Number of Transistors = TBD
Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com
12
PS7012H
08/30/04