IP78M05ADP IP78M05DPA SEME LAB MECHANICAL DATA 3 TERMINAL LOW CURRENT 5 VOLT POSITIVE VOLTAGE REGULATOR Dimensions in mm (inches) FEATURES • 0.01%/V LINE REGULATION • 0.3%/A LOAD REGULATION PostScript Picture C:\APPROVED\PACKAGES\PLASTIC\D PACK.EPS • THERMAL OVERLOAD PROTECTION • SHORT CIRCUIT PROTECTION • SAFE OPERATING AREA PROTECTION • 1% OUTPUT VOLTAGE TOLERANCE D–PACK — TO251 plastic package Pin 1 – VIN Pin 2 – GND Pin 3 – VOUT ABSOLUTE MAXIMUM RATINGS (Tcase = 25°C unless otherwise stated) VI DC Input Voltage 35V PD Power Dissipation Internally limited Tj Operating Junction Temperature Range Maximum Junction Temperature Tstg Storage Temperature Range TL Lead Temperature (Soldering, 10 sec) Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk 0°C to 125°C 125°C –65°C to +150°C 300°C Prelim. 9/94 IP78M05ADP IP78M05DPA SEME LAB ELECTRICAL CHARACTERISTICS (Tj = 25°C unless stated) Parameter VO Output Voltage* DVO Line Regulation* DVO Load Regulation* Id Quiescent Current* DIQ Quiescent Current Change* VN Test Conditions IO = 100mA VIN = 10V IO = 5mA to 350mA VIN = 7.5 to 20V Tj = 0 to 125°C PD £ PMAX IO = 200mA VIN = 7 to 25V IO = 200mA VIN = 8 to 25V Tj = 0 to 125°C IO = 500mA VIN = 8 to 12V IO = 5mA to 500mA VIN = 10V Tj = 0 to 125°C IO = 350mA VIN = 10V Tj = 0 to 125°C IO = 5 to 500mA VIN = 10V Tj = 0 to 125°C IO = 200mA VIN = 8 to 25V Tj = 0 to 125°C Min. 4.80 IP78M05DP Typ. Max. 5 5.20 4.85 4.75 5.25 VIN = 8 to 18V f = 120Hz IO = 300mA VIN = 8 to 18V f = 120Hz IO = 100mA Tj = 0 to 125°C IO = 350mA Dropout Voltage* Short Circuit Current* VIN = 35V Peak Output Current* VIN = 10V Average Temperature Coefficient of Output IO = 5mA 5.15 V 3 10 50 3 10 25 3 10 50 5 50 50 mV 4 6 6 mA 0.1 0.5 65 0.2 0.8 40 200 80 4 mV 0.5 0.8 40 200 mV 62 dB 65 80 0.7 2 300 1.0 2.5 600 1.4 300 1.0 0.5 2.0 0.5 Voltage* * Pulse Test: Unit mA Output Noise Voltage f = 10Hz to 100kHz DVIN Ripple Rejection DVO ISC IPK IP78M05ADP Min. Typ. Max. 4.95 5 5.05 62 2.5 600 1.6 V mA A mV / °C tp £ 10ms , d £ 5%. All characteristics are measured with a capacitor across the input of 0.22mF and a capacitor across the output of 0.1mF. Output Voltage changes due to changes in internal temperature must be taken into account separately. Semelab plc. Telephone +44(0)1455 556565. Fax +44(0)1455 552612. E-mail: [email protected] Website: http://www.semelab.co.uk Prelim. 9/94