® Advanced SP6139 Wide Input, 1.3MHz Synchronous PWM Controller FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ VCC 1 2.5V to 20V Step Down Achieved Using Dual Input Small 10-Pin MSOP Package Up to 15A Ouput Capability Highly Integrated Design, Minimal Components UVLO Detects Both VCC and VIN Short Circuit Protection with Auto-Restart On-Board 1.5Ω sink (2Ω source) NFET Drivers Programmable Soft Start Fast Transient Response High Efficiency: Greater than 94% Possible A Synchronous Start-Up into a Pre-Charged Output 10 BST GL 2 9 GH SP6139 8 SWN GND 3 10 Pin MSOP VFB 4 7 SS 6 UVIN COMP 5 Now Available in Lead Free Packaging APPLICATIONS ■ DSL Modems ■ Set-Top Boxes ■ 12V VIN Point of Load Apps. DESCRIPTION The SP6139 is a synchronous step-down switching regulator controller optimized for high efficiency. The part is designed to be especially attractive for dual supply, 12V step down with 5V used to power the controller. This lower VCC voltage minimizes power dissipation in the part. The SP6139 is designed to drive a pair of external NFETs using a fixed 1.3MHz frequency, PWM voltage mode architecture. Protection features include UVLO, thermal shutdown and output short circuit protection. The SP6139 is available in the cost and space saving 10-pin MSOP. TYPICAL APPLICATION CIRCUIT VIN 12V C1 22µF 16V 8 7 VCC = 5V @ 30mA Si4922DY 8.3A, 18mΩ QT GND 2 RLF 3.0,5% C1, C2 Ceramic 1210 X5R 1 CBST L1 SD25-2R2 2.2µH @ 2.8A 0.1µF 1 R3 150k, 1% CVCC 10µF 6.3V GND 3 2 3 4 0.8V 5 UVIN R4 100k, 1% CVCC Ceramic 8050 X5R BST 10 VCC GL SP6139 R5 Bead GH 9 GND SWN 8 VFB SS 7 RZ3 2.26k, 1% 5 6 Si4922DY 8.3A, 18mΩ QB 4 SS C3 47µF 6.3V C4 47µF 6.3V 3 CZ3 220pF VOUT≤VIN 3.3V @ 2A R1 68.1k, 1% UVIN 6 COMP RZ2 CZ2 1.2nF CSS 47nF GND2 12.7k, 1% C3, C4 Ceramic 1210 X5R CP1 CF1 100pF Date: 12/20/04 DCR=31mΩ U1 DBST MBR0530 39pF SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 1 R2 21.5k, 1% © Copyright 2004 Sipex Corporation ABSOLUTE MAXIMUM RATINGS Peak Output Current < 10us GH,GL ............................................................................................. 2A These are stress ratings only and functional operation of the device at these ratings or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Storage Temperature .................................................. -65°C to 150°C Power Dissipation .......................................................................... 1W Lead Temperature (Soldering, 10 sec) ...................................... 300°C ESD Rating .......................................................................... 2kV HBM Thermal Resistance ............................................................. 41.9°C/W VCC .................................................................................................. 7V BST ............................................................................................... 27V BST-SWN ......................................................................... -0.3V to 7V SWN ................................................................................... -1V to 20V GH ......................................................................... -0.3V to BST+0.3V GH-SWN ......................................................................................... 7V All other pins .......................................................... -0.3V to VCC+0.3V ELECTRICAL CHARACTERISTICS Unless otherwise specified: -40°C < TAMB < 85°C, 4.5V < VCC < 5.5V, BST=VCC,SWN = GND = 0V, UVIN = 3.0V, CVCC = 10µF, CCOMP = 0.1µF, CGH = CGL = 3.3nF, CSS = 50nF, Typical measured at VCC=5V. The ♦ denotes the specifications which apply over the full operating temperature range, unless otherwise specified. PARAMETER MIN TYP MAX UNITS ♦ CONDITIONS QUIESCENT CURRENT VCC Supply Current 1.5 BST Supply Current 0.2 0.4 mA mA ♦ VFB =0.9V (No switching) V ♦ V ♦ VFB =0.9V (No switching) PROTECTION: UVLO VCC UVLO Start Threshold 4.00 4.25 4.5 VCC UVLO Stop Threshold 3.80 4.05 4.4 VCC UVLO Hysteresis 200 mV UVIN Start Threshold 2.3 2.5 2.65 V ♦ UVIN Stop Threshold 2.0 2.2 2.35 V ♦ UVIN Hysteresis 300 mV ERROR AMPLIFIER REFERENCE Error Amplifier Reference 0.792 0.800 0.808 V Error Amplifier Reference Over Line and Temperature 0.788 0.800 0.812 V 2X Gain Config., Measure COMP/2 ♦ Error Amplifier Transconductance 6 ms Error Amplifier Gain 60 dB No Load COMP Sink Current 150 µA VFB = 0.9V, COMP = 0.9V COMP Source Current 150 µA VFB Input Bias Current 50 Internal Pole 4 COMP Clamp 2.5 V COMP Clamp Temp. Coefficient -2 mV/°C 200 nA VFB = 0.7V, COMP = 2.2V ♦ VFB = 0.8V MHz VFB=0.7V, TA = 25°C CONTROL LOOP: PWM COMPARATOR, RAMP & LOOP DELAY PATH Ramp Amplitude 0.92 RAMP Offset 1.1 RAMP Offset Temp. Coefficient -2 GH Minimum Pulse Width 90 Maximum Controllable Duty Ratio 92 Maximum Duty Ratio 100 Internal Oscillator Frequency 1.1 Date: 12/20/04 1.28 1.1 V ♦ V TA = 25°C, RAMP COMP until GH starts switching mV/°C 180 97 ns ♦ % ♦ % 1.3 1.5 MHz SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 2 Maximum Duty Ratio Measured just before pulse skipping begins Valid for 20 Cycles ♦ © Copyright 2004 Sipex Corporation ELECTRICAL CHARACTERISTICS Unless otherwise specified: 0°C < TAMB < 70°C, 4.5V < VCC < 5.5V, BST=VCC,SWN = GND = 0V, UVIN = 3.0V, CVCC = 10µF, CCOMP = 0.1µF, CGH = CGL = 3.3nF, CSS = 50nF, Typical measured at VCC=5V. The ♦ denotes the specifications which apply over the full operating temperature range, unless otherwise specified. PARAMETER MIN TYP MAX UNITS ♦ CONDITIONS mA ♦ Fault Present, SS = 0.2V V ♦ TIMERS: SOFTSTART SS Charge Current: 10 SS Discharge Current: µA 1 PROTECTION: SHORT CIRCUIT & THERMAL Short Circuit Threshold Voltage 0.2 0.25 0.3 Measured VREF (0.8V) - VFB Hiccup Timeout 50 ms VFB = 0V Number of Allowable Clock Cycles at 100% Duty Cycle 20 Cycles VFB = 0.7V Minimum GL Pulse After 20 Cycles 0.5 Cycles VFB = 0.7V Thermal Shutdown Temperature 145 °C Thermal Recovery Temperature 135 °C Thermal Hysteresis 10 °C OUTPUT: NFET GATE DRIVERS GH & GL Rise Times 35 50 ns ♦ Measured 10% to 90% GH & GL Fall Times 30 40 ns ♦ Measured 90% to 10% GL to GH Non Overlap Time 45 70 ns ♦ GH & GL Measured at 2.0V SWN to GL Non Overlap Time 20 30 ns ♦ Measured SWN = 100mV to GL = 2.0V GH & GL Pull Down Resistance 50 KΩ PIN DESCRIPTION PIN # 1 2 3 4 5 6 7 8 9 10 PIN NAME DESCRIPTION VCC Bias Supply Input. Connect to external 5V supply. Used to power internal circuits and low side gate driver. GL High current driver output for the low side NFET switch. It is always low if GH is high or during a fault. Resistor pull down ensure low state at low voltage. GND Ground Pin. The control circuitry of the IC and lower power driver are referenced to this pin. Return separately from other ground traces to the (-) terminal of COUT. VFB Feedback Voltage and Short Circuit Detection pin. It is the inverting input of the Error Amplifier and serves as the output voltage feedback point for the Buck Converter. The output voltage is sensed and can be adjusted through an external resistor divider. Whenever VFB drops 0.25V below the positive reference, a short circuit fault is detected and the IC enters hiccup mode. COMP Output of the Error Amplifier. It is internally connected to the non-inverting input of the PWM comparator. An optimal filter combination is chosen and connected to this pin and either ground or VFB to stabilize the voltage mode loop. UVIN UVLO input for VIN voltage. Connect a resistor divider between VIN and UVIN to set minimum operating voltage. SS Soft Start. Connect an external capacitor between SS and GND to set the soft start rate based on the 10µA source current. The SS pin is held low via a 1mA (min) current during all fault conditions. SWN Lower supply rail for the GH high-side gate driver. Connect this pin to the switching node at the junction between the two external power MOSFET transistors. GH High current driver output for the high side NFET switch. It is always low if GL is high or during a fault. Resistor pull down ensure low state at low voltage. BST High side driver supply pin. Connect BST to the external boost diode and capacitor as shown in the Typical Application Circuit on page 1. High side driver is connected between BST pin and SWN pin. Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 3 © Copyright 2004 Sipex Corporation FUNCTIONAL DIAGRAM 5 COMP VCC 100% Protection Logic PULSES CLR COUNT 20 CLOCK PWM LOOP VFBINT 10 BST RESET DOMINANT Gm ERROR AMPLIFIER VPOS VFB FAULT CLK Gm FAULT R VCC VCC Q FAULT QPWM 9 GH SYNCHRONOUS DRIVER S 8 SWN 2 GL 10 µA SS 7 SOFTSTART INPUT 1.2 MHZ POS REF RAMP = 1.1V CLK CLOCK PULSE GENERATOR FAULT 0.4 V GL HOLD OFF SS VCC 1 THERMAL SHUTDOWN 145 ˚C ON 135 ˚C OFF VPOS 0.25 V +- VFBINT 0.8V REFERENCE CORE 1.7 V 1.7 V REF OK ASYNC. STARTUP COMPARATOR 3 GND SET DOMINANT S SHORT CIRCUIT DETECTION + - HICCUP FAULT Q FAULT REF OK R VCC + 4.25 V ON 4.05 V OFF - VCC UVLO POWER FAULT + 2.50 VON 2.20 V OFF CLK COUNTER VIN UVLO 6 UVIN 200ms Delay CLR REF OK THERMAL AND SHORT CIRCUIT PROTECTION UVLO COMPARATORS THEORY OF OPERATION General Overview The SP6139 is a fixed frequency, voltage mode, synchronous PWM controller optimized for high efficiency. The part has been designed to be especially attractive for split plane applications utilizing 5V to power the controller and 2.5V to 20V for step down conversion. The SP6139 contains two unique control features that are very powerful in distributed applications. First, asynchronous driver control is enabled during start up to prohibit the low side NFET from pulling down the output until the high side NFET has attempted to turn on. Second, a 100% duty cycle timeout ensures that the low side NFET is periodically enhanced during extended periods at 100% duty cycle. This guarantees the synchronized refreshing of the BST capacitor during very large duty ratios. The heart of the SP6139 is a wide bandwidth transconductance amplifier designed to accommodate Type II and Type III compensation schemes. A precision 0.8V reference present on the positive terminal of the error amplifier permits the programming of the output voltage down to 0.8V via the VFB pin. The output of the error amplifier, COMP, compared to a 1.1V peak-to-peak ramp is responsible for trailing edge PWM control. This voltage ramp and PWM control logic are governed by the internal oscillator that accurately sets the PWM frequency to 1.3MHz. Date: 12/20/04 The SP6139 also contains a number of valuable protection features. A programmable input (VIN) UVLO allows a user to set the exact value at which the conversion voltage is at a safe point to begin down conversion, and an internal VCC UVLO ensures that the controller itself has enough voltage to properly operate. Other pro- SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 4 © Copyright 2004 Sipex Corporation THEORY OF OPERATION Hiccup tection features include thermal shutdown and short-circuit detection. In the event that either a thermal, short-circuit, or UVLO fault is detected, the SP6139 is forced into an idle state where the output drivers are held off for a finite period before a re-start is attempted. Upon the detection of a power, thermal, or shortcircuit fault, the SP6139 is forced into an idle state for 100mS (typical). The SS and COMP pins are immediately pulled low, and the gate drivers are held off for the duration of the timeout period. Power and thermal faults have to be removed before a restart may be attempted, whereas, a short-circuit fault is internally cleared shortly after the fault latch is set. Therefore, a restart attempt is guaranteed every 100mS (typical) as long as the short-circuit condition persists. Under Voltage Lock Out (UVLO) The SP6139 contains two separate UVLO comparators to monitor the bias (VCC) and conversion (VIN) voltages independently. The VCC UVLO threshold is internally set to 4.25V, whereas the VIN UVLO threshold is programmable through the UVIN pin. When the UVIN pin is greater than 2.5V, the SP6139 is permitted to start up pending the removal of all other faults. Both the VCC and VIN UVLO comparators have been designed with hysteresis to prevent noise from resetting a fault. Thermal and Short-Circuit Protection Because the SP6139 is designed to drive large NFETs running at high current, there is a chance that either the controller or power converter will become too hot. Therefore, an internal thermal shutdown (145°C) has been included to prevent the IC from malfunctioning at extreme temperatures. Soft Start “Soft Start” is achieved when a power converter ramps up the output voltage while controlling the magnitude of the input supply source current. In a modern step down converter, ramping up the positive terminal of the error amplifier controls soft start. As a result, excess source current can be defined as the current required to charge the output capacitor. A short-circuit detection comparator has also been included in the SP6139 to protect against the accidental short or sever build up of current at the output of the power converter. This comparator constantly monitors the positive and negative terminals of the error amplifier, and if the VFB pin ever falls more than 250mV (typical) below the positive reference, a short-circuit fault is set. Because the SS pin overrides the internal 0.8V reference during soft start, the SP6139 is capable of detecting short-circuit faults throughout the duration of soft start as well as in regular operation. IVIN = COUT * DVOUT / DTSoft-start The SP6139 provides the user with the option to program the soft start rate by tying a capacitor from the SS pin to GND. The selection of this capacitor is based on the 10uA pull up current present at the SS pin and the 0.8V reference voltage. Therefore, the excess source can be redefined as: Error Amplifier and Voltage Loop As stated before, the heart of the SP6139 voltage error loop is a high performance, wide bandwidth transconductance amplifier. Because of the amplifier’s current limited (+/-150µA) transconductance, there are many ways to compensate the voltage loop or to control the COMP pin externally. If a simple, single pole, single IVIN = COUT * DVOUT *10µA / (CSS * 0.8V) Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 5 © Copyright 2004 Sipex Corporation THEORY OF OPERATION zero response is required, then compensation can be a simple as an RC to ground. If a more complex compensation is required, then the amplifier has enough bandwidth (45° at 4 MHz) and enough gain (60dB) to run Type III compensation schemes with adequate gain and phase margins at cross over frequencies greater than 50kHz. GATE DRIVER TEST CONDITIONS 90% GH(GL) 2V FALL TIME 10% 90% RISE TIME 2V GL(GH) 10% NON-OVERLAP The common mode output of the error amplifier is 0.9V to 2.2V. Therefore, the PWM voltage ramp has been set between 1.1V and 2.2V to ensure proper 0% to 100% duty cycle capability. The voltage loop also includes two other very important features. One is an asynchronous start up mode. Basically, the GL driver can not turn on unless the GH driver has attempted to turn on or the SS pin has exceeded 1.7V. This feature prevents the controller from “dragging down” the output voltage during startup or in fault modes. The second feature is a 100% duty cycle timeout that ensures synchronized refreshing of the BST capacitor at very high duty ratios. In the event that the GH driver is on for 20 continuous clock cycles, a reset is given to the PWM flip flop half way through the 21st cycle. This forces GL to rise for the remainder of the cycle, in turn refreshing the BST capacitor. V(BST) GH Voltage V(SWN) V(VCC) GL Voltage 0V V(VIN) SWN Voltage -0V -V(Diode) V V(VIN)+V(VCC) BST Voltage V(VCC) TIME Gate Drivers The SP6139 contains a pair of powerful 2Ω SOURCE and 1.5Ω SINK drivers. These state of the art drivers are designed to drive external NFETs capable of handling up to 30A. Rise, fall, and non-overlap times have all been minized to achieve maximum efficiency. All drive pins GH, GL & SWN are monitored continuously to ensure that only one external NFET is ever on at any given time. Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 6 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION Inductor Selection I PEAK = I OUT (max) + There are many factors to consider in selecting the inductor including cost, efficiency, size and EMI. In a typical SP6139 circuit, the inductor is chosen primarily for value, saturation current and DC resistance. Increasing the inductor value will decrease output voltage ripple, but degrade transient response. Low inductor values provide the smallest size, but cause large ripple currents, poor efficiency and more output capacitance to smooth out the larger ripple current. The inductor must also be able to handle the peak current at the switching frequency without saturating, and the copper resistance in the winding should be kept as low as possible to minimize resistive power loss. A good compromise between size, loss and cost is to set the inductor ripple current to be within 20% to 40% of the maximum output current. and provide low core loss at the high switching frequency. Low cost powdered iron cores have a gradual saturation characteristic but can introduce considerable ac core loss, especially when the inductor value is relatively low and the ripple current is high. Ferrite materials, on the other hand, are more expensive and have an abrupt saturation characteristic with the inductance dropping sharply when the peak design current is exceeded. Nevertheless, they are preferred at high switching frequencies because they present very low core loss and the design only needs to prevent saturation. In general, ferrite or molypermalloy materials are better choice for all but the most cost sensitive applications. The switching frequency and the inductor operating point determine the inductor value as follows: L= The power dissipated in the inductor is equal to the sum of the core and copper losses. To minimize copper losses, the winding resistance needs to be minimized, but this usually comes at the expense of a larger inductor. Core losses have a more significant contribution at low output current where the copper losses are at a minimum, and can typically be neglected at higher output currents where the copper losses dominate. Core loss information is usually available from the magnetic vendor. VOUT (V IN (max) − VOUT ) VIN (max) FS Kr I OUT ( max) where: Fs = switching frequency Kr = ratio of the ac inductor ripple current to the maximum output current The peak to peak inductor ripple current is: I PP = The copper loss in the inductor can be calculated using the following equation: VOUT (VIN (max) − VOUT ) PL( Cu) = I L2 ( RMS ) RWINDING VI N (max) FS L where IL(RMS) is the RMS inductor current that can be calculated as follows: IL(RMS) = IOUT(max) 1 + 1 3 Once the required inductor value is selected, the proper selection of core material is based on peak inductor current and efficiency requirements. The core must be large enough not to saturate at the peak inductor current Date: 12/20/04 I PP 2 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 7 ( IPP IOUT(max) ) 2 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION Output Capacitor Selection FS = Switching Frequency The required ESR (Equivalent Series Resistance) and capacitance drive the selection of the type and quantity of the output capacitors. The ESR must be small enough that both the resistive voltage deviation due to a step change in the load current and the output ripple voltage do not exceed the tolerance limits expected on the output voltage. During an output load transient, the output capacitor must supply all the additional current demanded by the load until the SP6139CU adjusts the inductor current to the new value. D = Duty Cycle COUT = Output Capacitance Value Input Capacitor Selection The input capacitor should be selected for ripple current rating, capacitance and voltage rating. The input capacitor must meet the ripple current requirement imposed by the switching current. In continuous conduction mode, the source current of the high-side MOSFET is approximately a square wave of duty cycle VOUT/VIN. Most of this current is supplied by the input bypass capacitors. The RMS value of input capacitor current is determined at the maximum output current and under the assumption that the peak Therefore the capacitance must be large enough so that the output voltage is help up while the inductor current ramps up or down to the value corresponding to the new load current. Additionally, the ESR in the output capacitor causes a step in the output voltage equal to the current. Because of the fast transient response and inherent 100% and 0% duty cycle capability provided by the SP6139CU when exposed to output load transient, the output capacitor is typically chosen for ESR, not for capacitance value. to peak inductor ripple current is low, it is given by: ICIN(rms) = IOUT(max) √D(1 - D) The worse case occurs when the duty cycle D is 50% and gives an RMS current value equal to IOUT/2. Select input capacitors with adequate ripple current rating to ensure reliable operation. The output capacitor’s ESR, combined with the inductor ripple current, is typically the main contributor to output voltage ripple. The maximum allowable ESR required to maintain a specified output voltage ripple can be calculated by: The power dissipated in the input capacitor is: 2 PCIN = ICIN ( rms ) R ESR ( CIN ) RESR ≤ ∆VOUT IPK-PK This can become a significant part of power losses in a converter and hurt the overall energy transfer efficiency. The input voltage ripple primarily depends on the input capacitor ESR and capacitance. Ignoring the inductor ripple current, the input voltage ripple can be determined by: where: ∆VOUT = Peak to Peak Output Voltage Ripple IPK-PK = Peak to Peak Inductor Ripple Current The total output ripple is a combination of the ESR and the output capacitance value and can be calculated as follows: ( ∆VOUT = IPP (1 – D) COUTFS Date: 12/20/04 where: ) ∆ VIN = I out (max) RE SR (CIN ) + I OUT ( MAX )VOUT (VI N − VOUT ) FS C INV IN 2 2 + (IPPRESR)2 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 8 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION The capacitor type suitable for the output capacitors can also be used for the input capacitors. The total power losses of the top MOSFET are the sum of switching and conduction losses. For synchronous buck converters of efficiency over 90%, allow no more than 4% power losses for high or low side MOSFETs. For input voltages of 3.3V and 5V, conduction losses often dominate switching losses. Therefore, lowering the RDS(ON) of the MOSFETs always improves efficiency even though it gives rise to higher switching losses due to increased Crss. However, exercise extra caution when tantalum capacitors are considered. Tantalum capacitors are known for catastrophic failure when exposed to surge current, and input capacitors are prone to such surge current when power supplies are connected “live” to low impedance power sources. MOSFET Selection The losses associated with MOSFETs can be divided into conduction and switching losses. Conduction losses are related to the on resistance of MOSFETs, and increase with the load current. Switching losses occur on each on/off transition when the MOSFETs experience both high current and voltage. Since the bottom MOSFET switches current from/to a paralleled diode (either its own body diode or a Schottky diode), the voltage across the MOSFET is no more than 1V during switching transition. As a result, its switching losses are negligible. The switching losses are difficult to quantify due to all the variables affecting turn on/ off time. However, the following equation provides an approximation on the switching losses associated with the top MOSFET driven by SP6139. Top and bottom MOSFETs experience unequal conduction losses if their on time is unequal. For applications running at large or small duty cycle, it makes sense to use different top and bottom MOSFETs. Alternatively, parallel multiple MOSFETs to conduct large duty factor. RDS(ON) varies greatly with the gate driver voltage. The MOSFET vendors often specify RDS(ON) on multiple gate to source voltages (VGS), as well as provide typical curve of RDS(ON) versus VGS. For 5V input, use the RDS(ON) specified at 4.5V VGS. At the time of this publication, vendors, such as Fairchild, Siliconix and International Rectifier, have started to specify RDS(ON) at VGS less than 3V. This has provided necessary data for designs in which these MOSFETs are driven with 3.3V and made it possible to use SP6139 in 3.3V only applications. PSH (max) = 12C rssV IN (max) I OUT (max) FS where Crss = reverse transfer capacitance of the top MOSFET Thermal calculation must be conducted to ensure the MOSFET can handle the maximum load current. The junction temperature of the MOSFET, determined as follows, must stay below the maximum rating. Switching losses need to be taken into account for high switching frequency, since they are directly proportional to switching frequency. The conduction losses associated with top and bottom MOSFETs are determined by: TJ ( max) = T A (max) + 2 PCH (max) = RDS (ON ) I OUT (max) D PMOSFET (max) Rθ JA where 2 PCL(max) = R DS (ON ) I OUT (max) (1 − D) TA(max) = maximum ambient temperature PMOSFET(max) = maximum power dissipation of the MOSFET RΘJA = junction to ambient thermal resistance. where PCH(max) = conduction losses of the high side MOSFET PCL(max) = conduction losses of the low side MOSFET RΘJA of the device depends greatly on the board layout, as well as device package. Significant RDS(ON) = drain to source on resistance. Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 9 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION diode is equal to input voltage, and the diode must be able to handle the peak current equal to the maximum load current. thermal improvement can be achieved in the maximum power dissipation through the proper design of copper mounting pads on the circuit board. For example, in a SO-8 package, placing two 0.04 square inches copper pad directly under the package, without occupying additional board space, can increase the maximum power from approximately 1 to 1.2W. For DPAK package, enlarging the tap mounting pad to 1 square inches reduces the RΘJA from 96°C/W to 40°C/W. The power dissipation of the Schottky diode is determined by PDIODE = 2VFIOUTTNOLFS where Schottky Diode Selection TNOL = non-overlap time between GH and GL. When paralleled with the bottom MOSFET, an optional Schottky diode can improve efficiency and reduce noises. Without this Schottky diode, the body diode of the bottom MOSFET conducts the current during the non-overlap time when both MOSFETs are turned off. Unfortunately, the body diode has high forward voltage and reverse recovery problem. The reverse recovery of the body diode causes additional switching noises when the diode turns off. The Schottky diode alleviates these noises and additionally improves efficiency thanks to its low forward voltage. The reverse voltage across the VF = forward voltage of the Schottky diode. Loop Compensation Design The open loop gain of the whole system can be divided into the gain of the error amplifier, PWM modulator, buck converter output stage, and feedback resistor divider. In order to crossover at the selected frequency FCO, the gain of the error amplifier has to compensate for the attenuation caused by the rest of the loop at this frequency. Type III Voltage Loop Compensation GAMP (s) Gain Block VREF (Volts) + _ PWM Stage GPWM Gain Block VIN (SRz2Cz2+1)(SR1Cz3+1) (SRESRCOUT+ 1) VRAMP_PP SR1Cz2(SRz3Cz3+1)(SRz2Cp1+1) Output Stage GOUT (s) Gain Block [S^2LCOUT+S(RESR+RDC) COUT+1] VOUT (Volts) Notes: RESR = Output Capacitor Equivalent Series Resistance. RDC = Output Inductor DC Resistance. VRAMP_PP = SP6132 Internal RAMP Amplitude Peak to Peak Voltage. Condition: Cz2 >> Cp1 & R1 >> Rz3 Output Load Resistance >> RESR & RDC Voltage Feedback GFBK Gain Block R2 VFBK (Volts) (R1 + R2) or VREF VOUT SP6134 Voltage Mode Control Loop with Loop Dynamic Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 10 © Copyright 2004 Sipex Corporation APPLICATIONS INFORMATION The goal of loop compensation is to manipulate loop frequency response such that its gain crosses When the output capacitors are of a Ceramic Type, the SP6139CU Evaluation Board requires a Type III compensation circuit to give a phase boost of 180° in order to counteract the effects of an under damped resonance of the output filter at the double pole frequency. over 0db at a slope of -20db/dec. The first step of compensation design is to pick the loop crossover frequency. High crossover frequency is desirable for fast transient response, but often jeopardizes the system stability. Crossover frequency should be higher than the ESR zero but less than 1/5 of the switching frequency. The ESR zero is contributed by the ESR associated with the output capacitors and can be determined by: Gain (dB) Error Amplify Gain Bandwidth Product Condition: C22 >> CP1, R1 >> RZ3 1 ƒZ(ESR) = 20 Log (RZ2/R1) 1/6.28 (RZ3) (CZ3) 1/6.28 (RZ2) (CP1) The next step is to calculated the complex conjugate poles contributed by the LC output filter, 1/6.28 (R1) (CZ2) 1/6.28(R22) (CZ2) 1/6.28 (R1) (CZ3) 2π COUT RESR Frequency (Hz) Bode Plot of Type III Error Amplify Compensation. 1 ƒP(LC) = 2π L COUT INDUCTORS - SURFACE MOUNT Inductor Specification Inductance (uH) Manufacturer/Part No. Series R mΩ ISAT (a) Size LxW(mm) Ht.(mm) Inductor Type Manufaturer Website 2.7 2.7 3.3 Easy Magnet SC5018-2R7M TDK RLF 12560T-2R7N110 Coilcraft DO5010P-332HC 4.30 4.50 8.60 12.0 12.2 17.0 12.6x12.6 12.5x12.8 14.7x15.2 4.5 6.0 8.0 Shielded Ferrite Core Shielded Ferrite Core Unshielded Ferrite Core inter-technical.com tdk.com coilcraft.com 1.2 1.2 1.5 1.9 Easy Magnet SC5018-1R2M Inter-Technical SC4015-1R2M Coilcraft DO5010P-152HC TDK RLF 12560T-1R9N120 1.96 4.37 4.00 3.60 20.0 17.0 25.0 13.2 12.6x12.6 10.0x10.0 14.7x15.2 12.5x12.8 4.5 3.8 8.0 6.0 Shielded Ferrite Core Shielded Ferrite Core Unshielded Ferrite Core Shielded Ferrite Core inter-technical.com inter-technical.com coilcraft.com tdk.com CAPACITORS -SURFACE MOUNT Capacitance (uF) Manufacturer/Part No. ESR Ω (max) Ripple Current (A)@45°C Size LxW(mm) Ht.(mm) Voltage (V) Capacitor Type Manufaturer Website 22 TDK C3225X5R1C226M 0.002 4.00 3.2x2.5 2.0 16.0 X5R Ceramic tdk.com 47 TDK C3225X5ROJ476M 0.002 4.00 3.2x2.5 2.5 6.3 X5R Ceramic tdk.com MOSFET - Surface Mount MOSFET Manufacturer/Part No. RDS (on) Ω (max) ID Current (A) Qg nC(Typ) Qg nC(Max) Voltage (V) Foot Print Manufaturer Website fairchildsemi.com N-Channel Fairchild Semi FDS6676S 0.006 14.50 43 60.0 30.0 SO-8 N-Channel Fairchild Semi FD7088N3 0.005 21.10 37 48.0 30.0 SO-8 fairchildsemi.com 30.0 SO-8 vishay.com N-Channel Vishay Si4336DY 0.004 25.0 32 50.0 Note: Components highlighted in Bold are those used on the SP6134 Evaluation Board. Table 1. Input and Output Stage Components Selection Charts. Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 11 © Copyright 2004 Sipex Corporation PACKAGE: 10 PIN MSOP D e1 Ø1 R1 R E/2 Gauge Plane L2 E E1 Ø1 Seating Plane Ø L L1 1 2 e Pin #1 indentifier must be indicated within this shaded area (D/2 * E1/2) B B 10 Pin MSOP JEDEC MO-187 (BA) Variation MIN NOM MAX SYMBOL A 1.1 A1 0 0.15 A2 0.75 0.85 0.95 b 0.17 0.27 c 0.08 0.23 3.00 BSC D 4.90 BSC E 3.00 BSC E1 0.50 BSC e 2.00 BSC e1 L 0.4 0.6 0.8 0.95 REF L1 0.25 BSC L2 N 10 R 0.07 R1 0.07 ø 0º 8º ø1 0º 15º A2 A b A1 b WITH PLATING c Note: Dimensions in (mm) BASE METAL 1 Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 12 Section B-B © Copyright 2004 Sipex Corporation ORDERING INFORMATION Part Number Temperature Topmark Package SP6139EU........................-40°C to +85°C...................SP6139EU ........................... 10 Pin MSOP SP6139EU/TR..................-40°C to +85°C...................SP6139EU ........................... 10 Pin MSOP Available in lead free packaging. To order add "-L" suffix to part number. Example: SP6139EU/TR = standard; SP6139EU-L/TR = lead free /TR = Tape and Reel Pack quantity is 2,500 for MSOP. CLICK HERE TO ORDER SAMPLES Corporation ANALOG EXCELLENCE Sipex Corporation Headquarters and Sales Office 233 South Hillview Drive Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600 Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Date: 12/20/04 SP6139 Wide Input, 1.3MHz Synchronous PWM Controller 13 © Copyright 2004 Sipex Corporation