ZILOG Z8018533FSC

Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
PRELIMINARY PRODUCT SPECIFICATION
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
FEATURES
Part
Z80185
Z80195
ROM
(KB)
32 x 8
0
UART
Baud Rate
512 Kbps
512 Kbps
■
100-Pin QFP Package
■
5.0-Volt Operating Range
■
Low-Power Consumption
■
0°C to +70°C Temperature Range
Speed
(MHz)
20, 33
20, 33
■
Enhanced Z8S180 MPU
■
Four Z80 CTC Channels
■
One Channel ESCC™ Controller
■
Two 8-Bit Parallel I/O Ports
■
Bidirectional Centronics Interface (IEEE 1284)
■
Low-EMI Option
GENERAL DESCRIPTION
The Z80185 and Z80195 are smart peripheral controller
devices designed for general data communications applications, and architected specifically to accommodate all
input and output (I/O) requirements for serial and parallel
connectivity. Combining a high-performance CPU core
with a variety of system and I/O resources, the Z80185/195
are useful in a broad range of applications. The Z80195 is
the ROMless version of the device.
The Z80185 and Z80195 feature an enhanced Z8S180
microprocessor linked with one enhanced channel of the
Z85230 ESCC™ serial communications controller, and 25
bits of parallel I/O, allowing software code compatibility
with existing software code.
Seventeen lines can be configured as bidirectional
Centronics (IEEE 1284) controllers. When configured as a
1284 controller, an I/O line can operate in either the host or
peripheral role in compatible, nibble, byte or ECP mode. In
addition, the Z80185 includes 32 Kbytes of on-chip ROM.
These devices are well-suited for external modems using
a parallel interface, protocol translators, and cost-effective
WAN adapters. The Z80185/195 is ideal for handling all
laser printer I/O, as well as the main processor in costeffective printer applications.
Notes:
All Signals with a preceding front slash, "/", are active Low.
Power connections follow conventional descriptions below:
DS971850301
Connection
Circuit
Device
Power
Ground
VCC
GND
VDD
VSS
1
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
TIMING DIAGRAMS (Continued)
16-Bit Address Bus
MMU
A19-0
Processor
8-Bit Data Bus
Decode
/ROMCS
/RAMCS
Power Controller
DMACs (2)
TxD,
RxD
ROM
32K x 8
(Z80185 Only)
EMSCC
Parallel Ports (2)
Including IEEE
Bidirectional
Centronics Controller
TOUT
CLK/TRG
16-Bit Programmable
Reload Timers (2)
UARTs (2)
CTCs (4)
TXA1-0,
RXA1-0
ZC/TO
Figure 1. Z80185/195 Functional Block Diagram
2
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
/INT1
/INT2
100
1
90
95
/HALT
VDD
/RFSH
/IORQ
/MREQ
NFAULT
/M1
/WR
/RD
PHI
A17
VSS
XTAL
/WAIT
EXTAL
/BUSACK
/RESET
/BUSREQ
/NMI
/INT0
PIN DESCRIPTION
80
85
NACK
ST
NAUTOFD
A0
A1
NSTROBE
TOUT//DREQ
5
BUSY
75
A2
NINIT
A3
RXA1
A15
/IOCS
A4
A5
TXA1
10
CKA0/CKS
70
A6
RXA0
A7
TXA0
A8
/DCD0/CKA1
A9
A10
/CTS0/RXS
Z80185/Z80195
100-Pin QFP
15
A11
/RTS0/TXS
65
A18
A12
A19
VSS
VSS
IEI
A13
A14
/ROMCS
20
60
A16
IEO
D0
VSS
D1
/DCD
D2
D3
/CTS
25
/RTS
55
D4
/DTR
D5
TXD
D6
/TRXC
D7
RXD
PERROR
NSELECTIN
/RTXC
PIA27
PIA26
50
PIA25
PIA24
PIA23
PIA22
PIA21
45
PIA20
VSS
VDD
SELECT
PIA16/ZCTO2
40
PIA15/ZCTO1
PIA13/CLKTRG3
PIA12/CLKTRG2
PIA11/CLKTRG1
PIA14/ZCTO0
35
30
PIA10/CLKTRG0
/RAMCS
Figure 2. 100-Pin QFP Pin Assignments
DS971850301
3
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
ABSOLUTE MAXIMUM RATINGS
Symbol Description
V CC
V IN
TOPR
TSTG
Min
Supply Voltage
–0.3
Input Voltage
–0.3
Operating Temp.
0
Storage Temp.
–55
Max
Units
+7.0
V CC+0.3
70
+150
V
V
°C
°C
Stresses greater than those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; operation of the device at
any condition above those indicated in the operational
sections of these specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods
may affect device reliability.
Notes:
Voltage on all pins with respect to GND. Permanent LSI damage may
occur if maximum ratings are exceeded. Normal operation should be
recommended operating conditions. If these conditions are exceeded, it
could affect reliability of LSI.
STANDARD TEST CONDITIONS
The DC Characteristics and capacitance sections below
apply for the following standard test conditions, unless
otherwise noted. All voltages are referenced to GND (0V).
Positive current flows into the referenced pin (Test Load).
I OL = 2 mA
Operating Temperature Range:
S = 0°C to 70°C
1.4 V
Voltage Supply Range:
+4.5V ≤ VCC ≤ +5.5V
All AC parameters assume a load capacitance of 100 pF.
Add 10 ns delay for each 50 pF increase in load up to a
maximum of 150 pF for the data bus and 100 pF for
address and control lines. AC timing measurements are
referenced to 1.5 volts (except for clock, which is referenced to the 10% and 90% points). Maximum capacitive
load for PHI is 125 pF.
4
100 pF
I OH = 250 µA
Figure 3. Test Load Diagram
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
DC CHARACTERISTICS
V DD = 5.0V ± 10%, V SS = 0V over specified temperature range, unless otherwise noted.
Symbol
Item
Condition
V IH
Input “H” Voltage
†
V
V IL
Input “L” Voltage
†
V
VOH
Output “H” Voltage
†
V
VOL1
Output “L” Voltage
†
V
Input Leakage
Current All Inputs
Except XTAL,EXTAL
V IN=0.5 to
V DD–0.5
1.0
Tri-State Leakage
Current
V IN=0.5 to
V DD–0.5
1.0
µA
V DD Supply Current*
Normal Operation
For 5.0V:
For 5.0V:
f = 20 MHz
f = 33 MHz
60
68
120
132
mA
mA
Power Dissipation*
System Stop Mode
For 5.0V:
For 5.0V:
f = 20 MHz
f = 33 MHz
5
7
10
13
mA
mA
IIL
ITL
ICC*
Min.
Typ.
Max.
Unit
µA
Notes:
† See Class Reference Table
* V IH min = VDD –1.0V, VIL max = 0.8V (All output terminals are at no load.)
DS971850301
5
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
TIMING DIAGRAMS
Z8S180 MPU Timing
Opcode Fetch Cycle
T1
T2
TW
T3
I/O Write Cycle †
I/O Read Cycle †
T2
TW
T1
T3
T1
5
4
2
3
ø
1
6
Address
20
20
19
19
/WAIT
11
12
7
/MREQ
7
8
/IORQ
11
29
28b
11
9b
13
13
28a
/RD
9a
11
9
22
25
26 and 26a
/WR
14
/M1
10
18
ST
16
17
15
16
15
21
Data
IN
27
23
24
Data
OUT
49
49
48
48
/RESET
54
54
53
53
Figure 4. CPU Timing
(Opcode Fetch Cycle, Memory Read/Write Cycle
I/O Read/Write Cycle)
6
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
TIMING DIAGRAMS (Continued)
Ø
32
31
/INTI
33
/NMI
/M1 [1]
30
/IORQ [1]
16
15
/Data IN [1]
39
/MREQ [2]
41
40
42
/RFSH [2]
35
35
34
34
/BUSREQ
36
37
/BUSACK
38
38
Address
Data /MREQ,
/RD, /WR,
/IORQ
43
[3]
44
/HALT
Notes:
[1] During /INT0 acknowledge cycle
[2] During refresh cycle
[3] Output buffer is off at this point
[4] Refer to Table C, parameter 7
Figure 5. CPU Timing
(/INT0 Acknowledge Cycle, Refresh Cycle, BUS RELEASE mode
HALT mode, SLEEP mode, SYSTEM STOP mode)
DS971850301
7
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
I/O Read Cycle
T1
T2
I/O Write Cycle
TW
T3
T1
T2
TW
T3
0
Address
28
29
9
13
28
29
/IROQ
/RD
22
25
/WR
Figure 6. CPU Timing
CPU or DMA Read/Write Cycle
T1
T2
Tw
T3
T1
Ø
45
46 [1]
TOUT//DREQ
(At level
sense)
45
45 [2]
TOUT//DREQ
(At edge
sence)
[3]
18
[4]
17
ST
DMA Control Signals
[1] tDRQS and tDRQH are specified for the rising edge of clock followed by T3.
[2] tDRQS and tDRQH are specified for the rising edge of clock.
[3] DMA cycle starts.
[4] CPU cycle starts.
Figure 7. DMA Control Signals
8
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
TIMING DIAGRAMS (Continued)
Ø
Timer Data
Reg = 0000H
TOUT/DREQ
47
Figure 8. Timer Output Timing
SLP Instruction Fetch
T3
Next Opcode Fetch
T1
T2
TS
TS
T1
T2
Ø
32
31
/INTi
/NMI
33
A18-A0
/MREQ, /M1
/RD
43
44
/HALT
Figure 9. SLEEP Execution Cycle
DS971850301
9
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
CSI/O Clock
57
57
Transmit Data
(Internal Clock)
58
58
11 tcyc
11 tcyc
Transmit Data
(External Clock)
59
60
59
60
Receive Data
(Internal Clock)
11.5 tcyc
11.5 tcyc
16.5 tcyc
16.5 tcyc
Receive Data
(External Clock)
61
62
61
62
Figure 10. CSI/O Receive/Transmit Timing
10
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
TIMING DIAGRAMS (Continued)
63
/MREQ
/RAMCS
/ROMCS
/IORQ
64
/IOCS
Figure 11. /ROMCS and /RAMCS Timing
51
EXTAL
VIL1
VIH1
52
VIH1
55
VIL1
Figure 12. External Clock Rise Time
and Fall Time
DS971850301
56
Figure 13. Input Rise and Fall Time
(Except EXTAL, /RESET)
11
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS
VDD = 5V ± 10%, VSS = 0V, CL = 50 pF for outputs over
specified temperature range, unless otherwise noted.
No. Symbol Parameter
Z80185 / Z80195
(20 MHz)
Min
Max
1
2
3
4
5
6
tcy
tCHW
tCLW
tcf
tcr
tAD
Clock Cycle Time
Clock “H” Pulse Width
Clock “L” Pulse Width
Clock Fall Time
Clock Rise Time
PHI Rising to Address Valid
7
8
9a
9b
10
11
12
13
tAS
tMED1
tRDD1
tRDD1
tM1D1
tAH
tMED2
tRDD2
Address Valid to (MREQ Falling or IORQ Falling)
PHI Falling to MREQ Falling Delay
PHI Falling to RD Falling Delay (IOC=1)
PHI Rising to RD Falling Delay (IOC=0)
PHI Rising to M1 Falling Delay
Address Hold Time from (MREQ, IOREQ, RD, WR)
PHI Falling to MREQ Rising Delay
PHI Falling to RD Rising Delay
14
15
16
17
18
19
20
tM1D2
tDRS
tDRH
tSTD1
tSTD2
tWS
tWH
PHI Rising to M1 Rising Delay
Data Read Setup Time
Data Read Hold Time
PHI Falling to ST Falling Delay
PHI Falling to ST Rising Delay
WAIT Setup Time to PHI Falling
WAIT Hold Time from PHI Falling
21
22
23
24
25
26
26a
27
tWDZ
tWRD1
tWDD
tWDS
tWRD2
tWRP
tWRP
WDH
PHI Rising to Data Float Display
PHI Rising to WR Falling Delay
PHI Rising to Write Data Delay Time
Write Data Setup Time to WR Falling
PHI Falling to WR Rising Delay
Write Pulse Width (Memory Write Cycle)
Write Pulse Width (I/O Write Cycle)
Write Data Hold Time From (WR Rising)
50
15
15
(DC)
Z80185 / Z80195
(33 MHz)
Min
Max
33
10
10
10
10
30
5
5
15
5
5
25
25
25
35
5
15
15
15
15
5
25
25
15
15
40
10
0
15
5
0
30
30
15
10
15
15
10
5
35
25
25
10
20
15
15
10
25
75
130
10
(DC)
15
45
70
5
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes:
Specifications 1 through 5 refer to an external clock input on EXTAL, and
provisionally to PHI clock output. When a quartz crystal is used with the
on-chip oscillator, a lower maximum frequency than that implied by spec.
#1 may apply.
12
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
No. Symbol Parameter
28a
28b
29
30
31
32
tIOD
tIOD
tIOD2
tIOD3
tINTS
tINTH
PHI Falling to IORQ Falling Delay IOC = 1)
PHI Rising to IORQ Fallin g Delay (IOC =0)
PHI Falling to IORQ Rising Delay
M1 Falling to IORQ Falling Delay
INT Setup Time to PHI Falling
INT Hold Time from PHI Falling
33
34
35
36
37
tNMIW
tBRS
tBRH
tBAD1
tBAD2
NMI Pulse Width
BUSREQ Setup Time to PHI Falling
BUSREQ Hold Time from PHI Falling
PHI Rising to BUSACK Falling Delay
PHI Falling to BUSACK Rising Delay
38
39
40
41
42
tBZD
tMEWH
tMEWL
tRFD1
tRFD2
PHI Rising to Bus Floating Delay Time
MREQ Pulse Width (High)
MREQ Pulse Width (Low)
PHI Rising to RFSH Falling Delay
PHI Rising to RFSH Rising Delay
43
44
45
46
47
tHAD1
tHAD2
tDRQS
tDRQH
tTOD
PHI Rising to HALT Falling Delay
PHI Rising to HALT Rising Delay
DREQ Setup Time to PHI Rising
DREQ Hold Time from PHI Rising
PHI Falling to Timer Output Delay
48
49
50
51
52
tRES
tREH
tOSC
tEXr
tEXf
RESET Setup Time to PHI Falling
RESET Hold Time From PHI Falling
Oscillator Stabilization Time
External Clock Rise Time (EXTAL)
External Clock Fall Time (EXTAL)
53
54
55
56
57
tRr
tRf
tIr
tIf
tSTDI
Reset Rise Time
Reset Fall Time
Input Rise Time (Except EXTAL, RESET)
Input Fall Time (Except EXTAL, RESET)
CSIO Transmit Data Delay Time
(Internal Clock Operation)
58
tSTDE
59
tSRSI
60
tSRHI
CSIO Transmit Data Delay Time
(External Clock Operation)
CSIO Receive Data Setup Time
(Internal Clock Operation)
CSIO Receive Data Hold Time
(Internal Clock Operation)
61
tSRSE
62
tSRHE
63
64
tdCS
tdIOCS
DS971850301
CSIO Receive Data Setup Time
(External Clock Operation)
CSIO Receive Data Hold Time
(External Clock Operation)
MREQ Valid to RAMCS and ROMCS Valid Delay
Rising IORQ Valid to Rising IOCS Valid Delay
Z80185 / Z80195
(20 MHz)
Min
Max
Z80185 / Z80195
(33 MHz)
Min
Max
25
25
25
15
15
15
100
20
10
80
15
10
35
10
10
25
10
10
25
25
15
15
40
tcy –15
2tcy –15
30
tcy –10
2tcy–10
20
20
15
15
15
15
15
15
20
20
75
40
25
15
15
50
25
15
Units
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
20
10
10
20
5
5
ns
ns
ms
ns
ns
50
50
50
50
75
50
50
50
50
60
ms
ms
ns
ns
ns
7.5 tcy +75
7.5 tcy +60
ns
75
60
ns
75
60
ns
75
60
ns
75
60
ns
15
10
15
10
ns
ns
13
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
Read/Write External Bus Master Timing
Address
A7-A0
/IORQ
B7
/RD
B8
B2
B4
B1
B5
Data
Data Out
B2
/WR
B9
B6
B3
Data
Data In
Figure 14. Read/Write External Bus Master Timing
14
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
General-Purpose I/O Timing Port Timing
Parameters referenced in Figure 15 appear in the following
Tables. Note: Port 2 timing is different, even when Bidirectional Centronics feature is not in active use.
I/O Port Timing
(Output)
T1
0
TW
T2
T3
T1
Port Data Dir. Reg. Addr. (Input)
A0-A7
TW
T2
T3
T1
Port Data Reg. Addr. (Input)
T3
Port Data Reg. Addr. (Input)
B7
B7
B7
TW
T2
/IORQ
Port Output Data 1
(In)
(In) 'OO'H (Change Port To
Output)
D0-D7
B6
B3
B6
Port Output Data 2 (In)
B3
B6
/WR
B2
B2
B2
Port
Port Output Data 1 (Out)
Port (Output)
A1
A1
A2
I/O Port Timing (Input)
Port Data Dir. Reg.
Addr. (Input)
A0-A7
Port Data Reg.
Addr. (Input)
Port Data Reg.
/IORQ
(In) 'FF'H (Change
Port To Input)
D0-D7
Port Data
2 Out
Port Data 1 (Out)
/WR
B2
B2
B4
B4
/RD
Port
Previous
Output
Port Input Data
1 (In)
Port Input Data
2 (In)
Figure 15. PORT Timing
DS971850301
15
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
I/O Port Timing
No. Symbol
A1
Parameter
TdWR (PIA)
Data Valid Delay from WR Rise
Z80185 / Z80195
(20 MHz)
Min
Max
60
Z80185 / Z80195
(33 MHz)
Min
Max
60
Units
ns
External Bus Master Timing
Z80185 / Z80195
(20 MHz)
Min
Max
Z80185 / Z80195
(33 MHz)
Min
Max
No. Symbol
Parameter
B1
Address Valid to WR or
RD Fall Time
IORQ Fall to WR or
RD Fall Time
Data Hold Time (from WR Rise)
RD Fall to Data Out Delay
40
40
ns
B3
B4
TsA(wf)
(rf)
TsIO(wf)
(rf)
Th
TdRD(DO)
20
5
35
20
5
35
ns
ns
ns
B5
B6
B7
B8
B9
TdRIr(DOz)
TsDI(WRf)
TsA(IORQf)
TsA(RDf)
TsA(WRf)
RD,IORQ Rise to Data Float Time
Data In to WR Fall Setup Time
Address to IORQ Fall Setup Time
Address to RD Fall Setup Time
Address to WR Fall Setup Time
5
20
20
40
40
5
20
20
40
40
ns
ns
ns
ns
ns
B2
16
Units
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
EMSCC Timing
Ø
/WR
/RD
1
Wait
2
/INT
6
Figure 16. EMSCC AC Parameters
EMSCC Timing Parameters
No.
1
2
6
DS971850301
Symbol
Parameter
TdWR(W)
TdRD(W)
TdPC(INT)
/WR Fall to Wait Valid Delay
/RD Fall to Wait Valid Delay
Clock to /INT Valid Delay
20 MHz
Min
Max
50
50
160
Unit
ns
17
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
EMSCC General Timing Diagram
PCLK
2
Wait
3
/RTxC, /TRxC
Receive
4
5
6
7
RxD
10
/TRxC, /RTxC
Transmit
11
12
TxD
13
/TRxC
Output
14
15
/RTxC
16
17
/TRxC
18
19
20
/CTS, /DCD
21
21
Figure 17. EMSCC General Timing Diagram
18
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
EMSCC General Timing
No.
20 MHz
Min
Max
Symbol
Parameter
Notes
2
3
4
5
TdPC(W)
TsRxC(PC)
TsRxD(RxCr)
ThRxD(RxCr)
/PCLK to Wait Inactive
/RxC to /PCLK Setup Time
RxD to /RxC Setup Time
RxD to /RxC Hold Time
6
7
10
11
TsRxD(RxCf)
ThRxD(RxCf)
TsTxC(PC)
TdTxCf(TXD)
RxD to /RxC Setup Time
RxD to /RxC Hold Time
/TxC to /PCLK Setup Time
/TxC to TxD Delay
12
13
14
15
TdTxCr(TXD)
TdTxD(TRX)
TwRTxh
TwRTxI
/TxC to TxD Delay
TxD to TRxC Delay
RTxC High Width
TRxC Low Width
80
70
70
[2,5]
70
[6]
[6]
16a
16b
17
18
TcRTx
TxRx(DPLL)
TcRTxx
TwTRxh
RTxC Cycle Time
DPLL Cycle Time Min
Crystal OSC. Period
TRxC High Width
200
50
61
70
[6,7]
[7,8]
[3]
[6]
19
20
21
TwTRxl
TcTRx
TwExT
TRxC Low Width
TRxC Cycle Time
DCD or CTS Pulse Width
70
200
60
170
NA
0
45
0
45
NA
70
70
1000
[1,4]
[1]
[1]
[1,5]
[1,5]
[2,4]
[2]
[6]
[6,7]
Notes:
[1] RxC is /RTxC or /TRxC, whichever is supplying the receive clock.
[2] TxC is /TRxC or /RTxC, whichever is supplying the transmit clock.
[3] Both /RTxC and /SYNC have 30 pF capacitors to Ground connected to them.
[4] Synchronization of RxC to PCLK is eliminated in divide-by-four operation.
[5] Parameter applies only to FM encoding/decoding.
[6] Parameter applies only for transmitter and receiver; DPLL and baud
rate generator timing requirements are identical to case PCLK requirements.
[7] The maximum receive or transmit data rate is 1/4 PCLK.
[8] Applies to DPLL clock source only. Maximum data rate of 1/4 PCLK
still applies. DPLL clock should have a 50% duty cycle.
These AC parameter values are preliminary and subject to change without notice.
DS971850301
19
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
EMSCC System Timing Diagram
/RTxC, /TRxC
Receive
/W/REQ
Wait
2
/INT
4
/RTxC, /TRxC
Transmit
Wait
6
/INT
8
/CTS,
/DCD
/INT
10
Figure 18. EMSCC System Timing
20
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
EMSCC System Timing
20 MHz
No.
Symbol
Parameter
Min
Max
2
4
TdRxC(W)
TdRxC(INT)
/RxC to /Wait Inactive
/RxC to /INT Valid
13
15
18
22
[1,2]
[1,2]
6
8
10
TdTxC(W)
TdTxC(INT)
TdExT(INT)
/TxC to /Wait Inactive
/TxC to /INT Valid
/DCD or /CTS to /INT Valid
8
9
3
17
17
9
[1,3]
[1,3]
[1]
Notes:
[1] Open-drain output, measured with open-drain test load.
[2] /RxC is /RTxC or /TRxC, whichever is supplying the receive clock.
Notes
[3] /TxC is /TRxC or /RTxC, whichever is supplying the transmit clock.
[4] Units equal to TcPc
These AC parameter values are preliminary and subject to change
without notice.
Valid ESCC
Addr * IORQ
1
/RD or
/WR
Figure 19. EMSCC External Bus Master Timing
External Bus Master Interface Timing (SCC Related Timing)
No
Symbol
Parameter
1
TrC
Valid Access Recovery Time
Z80185 / Z80195
(20 MHz)
Min
Max
4TcC
Z80185 / Z80195
(33 MHz)
Min
Max
4TcC
Unit
Notes
ns
[1]
Notes:
[1] Applies only between transactions involving the EMSCC.
These AC parameter values are preliminary and subject to change
without notice.
TCC = EMSCC Clock Period Time
DS971850301
21
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
AC CHARACTERISTICS (Continued)
φ
1
Port 2
Output
2
Control
Output
4
Control
Input
3
6
Port 2
Input
5
Figure 20. P1284 Bidirectional Centronics Interface Timing
P1284 Bidirectional Centronics Interface Timing
No.
Parameter
Min
Max
Units
Notes
1
CLK High to Port 2 Output
12
ns
2
CLK High to Control Output
12
ns
[1]
3
Setup Time for Control Input to
CLK High for Guaranteed Recognition
10
ns
[2]
Hold Time for Control Input from
CLK High for Guaranteed Recognition
5
ns
[2]
Setup Time for Port 2 Inputs to
CLK High for Guaranteed Recognition
10
ns
Hold Time for Port 2 Inputs to
CLK High for Guaranteed Recognition
5
ns
4
5
6
Notes:
[1]
22
Control Outputs
[2]
Control Inputs
Peripheral Mode
Host Mode
Host Mode
Peripheral Mode
Busy/PtrBusy/PeriphAck
nAck/PtrClk/PeriphClk
PError/AckDataReq/nAckReverse
nFault/nDataAvail/nPeriphRequest
Select/Xflag
nStrobe/HostClk
nAutoFd/HostBusy/HostAck
nSelectIn/P1284Active
nInit/nReverseRequest
Busy/PtrBusy/PeriphAck
nAck/PtrClk/PeriphClk
PError/AckDataReq/nAckReverse
nFault/nDataAvail/nPeriphRequest
Select/Xflag
nStrobe/HostClk
nAutoFd/HostBusy/HostAck
nSelectIn/P1284Active
nInit/nReverseRequest
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
PIN DESCRIPTIONS
Z80185 CPU Signals
A0-A19. Address Bus (input/output, active High, tri-state).
A0-A19 is a 20-bit address bus that provides the address
for memory data bus cycles up to 1 Mbyte, and I/O data
bus cycles up to 64 Kbytes. The address bus enters a High
impedance state during reset and external bus acknowledge cycles. This bus is an input when /BUSACK is Low.
No address lines are multiplexed with any other signals.
D0-D7. Data Bus (bidirectional, active High, tri-state). D0D7 constitute an 8-bit bidirectional data bus, used to
transfer information to and from I/O and memory devices.
The data bus enters the High impedance state during reset
and external bus acknowledge cycles, as well as during
SLEEP and HALT states.
/RD. Read (input/output, active Low, tri-state). /RD indicates that the CPU is ready to read data from memory or
an I/O device. The addressed I/O or memory device
should use this signal to gate data onto the CPU data bus.
This pin is tri-stated during bus acknowledge cycles.
/WR. Write (input/output, active Low, tri-state). /WR indicates that the CPU data bus holds valid data to be stored
at the addressed I/O or memory location. This pin is tristated during bus acknowledge cycles.
/IORQ. I/O Request (input/output, active Low, tri-state).
/IORQ indicates that the address bus contains a valid I/O
address for an I/O read or I/O write operation. /IORQ is also
generated, along with /M1, during the acknowledgment of
the /INT0 input signal to indicate that an interrupt response
vector can be placed onto the data bus. This pin is tristated during bus acknowledge cycles.
/M1. Machine Cycle 1 (input/output, active Low). Together
with /MREQ, /M1 indicates that the current cycle is the
opcode fetch cycle of an instruction execution. Together
with /IORQ, /M1 indicates that the current cycle is for an
interrupt acknowledge. It is also used with the /HALT and
ST signal to indicate the status of the CPU machine cycle.
The processor can be configured so that this signal is
compatible with the /M1 signal of the Z80, or with the /LIR
signal of the Z64180. This pin is tri-stated during bus
acknowledge cycles.
/MREQ. Memory Request (input/output, active Low, tristate). /MREQ indicates that the address bus holds a valid
address for a memory read or memory write operation. It is
included in the /RAMCS and /ROMCS signals, and because of this may not be needed in some applications. This
pin is tri-stated during bus acknowledge cycles.
DS971850301
/WAIT. (input/open-drain output, active Low.) /WAIT indicates to the MPU that the addressed memory or I/O
devices are not ready for a data transfer. This input is used
to induce additional clock cycles into the current machine
cycle. External devices should also drive this pin in an
open-drain fashion. This results in a “wired OR” of the Wait
indications produced by external devices and those produced by the two separate Wait State generators in the
Z80185. If the wire-ORed input is sampled Low, then
additional wait states are inserted until the /WAIT input is
sampled High, at which time the cycle is completed.
/HALT. Halt/Sleep Status (output, active Low). This output
is asserted after the CPU has executed either the HALT or
SLP instruction, and is waiting for either non-maskable or
maskable interrupt before operation can resume. It is also
used with the /M1 and /ST signals to indicate the status of
the CPU machine cycle. On exit of Halt/Sleep, the first
instruction fetch is delayed 16 clock cycles after the /HALT
pin goes High.
/BUSACK. Bus Acknowledge (output, active Low).
/BUSACK indicates to the requesting device that the MPU
address and data bus, as well as some control signals,
have entered their High impedance state.
/BUSREQ. Bus Request (input, active Low). This input is
used by external devices (such as DMA controllers) to
request access to the system bus. This request has a
higher priority than /NMI and is always recognized at the
end of the current machine cycle. This signal stops the
CPU from executing further instructions and places the
address and data buses, and other control signals, into the
High impedance state.
/NMI. Non-Maskable Interrupt (input, negative edge triggered). /NMI has a higher priority than /INT and is always
recognized at the end of an instruction, regardless of the
state of the interrupt enable flip-flops. This signal forces
CPU execution to continue at location 0066H.
/INT0. Maskable Interrupt Request 0 (input/open-drain
output, active Low). This signal is generated by internal
and external I/O devices. External devices should also
drive this signal in an open-drain fashion. The CPU will
honor this request at the end of the current instruction cycle
as long as it is enabled, and the /NMI and /BUSREQ signals
are inactive. The CPU acknowledges this interrupt request
with an interrupt acknowledge cycle. During this cycle,
both the /M1 and /IORQ signals will become active.
23
Zilog
P R E L I M I N A R Y
/INT1, /INT2. Maskable Interrupt Requests 1 and 2 inputs,
active Low). These signals are generated by external I/O
devices. The CPU will honor these requests at the end of
the current instruction cycle as long as the /NMI, /BUSREQ,
and /INT0 signals are inactive. The CPU will acknowledge
these interrupt requests with an interrupt acknowledge
cycle. Unlike the acknowledgment for /INT0 during this
cycle, neither the /M1 nor the /IORQ signals will become
active. These pins may be programmed to provide active
Low level, rising or falling edge interrupts. The level of the
external /INT1 and /INT2 pins may be read in the Interrupt
Edge Register.
/RFSH. Refresh (output, active Low, tri-state). /RFSH and
/MREQ active indicate that the current CPU machine cycle
and the contents of the address bus should be used for
refresh of dynamic memories. The low order eight bits of
the address bus (A7-A0) contain the refresh address.
Z80185 UART and CSIO Signals
CKA0/CKS. Asynchronous Clock 0 or Serial Clock (input/
output). An optional clock input or output for ASCI channel
0 or the Clocked Serial I/O Port.
/DCD0/CKA1. Data Carrier Detect 0 or Asynchronous
Clock 1 (input/output). A Low-active modem status input
for ASCI channel 0, or a clock input or output for ASCI
channel 1.
/RTS0/TxS. Request to Send 0 or Clocked Serial Transmit
Data (output). A programmable modem control output for
ASCI channel 0, or the serial output from the CSIO channel.
/CTS0/RxS. Clear to Send 0 or Clocked Serial Receive
Data (input). A Low-active modem control input for ASCI
channel 0, or the serial data input to the CSIO channel.
TXA0. Transmit Data 0 (output). This output transmits data
from ASCI channel 0.
RXA0. Receive Data 0 (input). This input receives data for
ASCI channel 0.
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Multiplexed Signal
TOUT//DREQ. Timer Out or External DMA Request (input
or output). This pin can be programmed to be either TOUT,
the High-active pulse output from PRT channel 1, or a Lowactive DMA Request input from an external peripheral.
Z80185 EMSCC Signals
TXD. Transmit Data (output). This output transmits serial
data at standard TTL levels.
RXD. Receive Data (input). This input receives serial data
at standard TTL levels.
/TRXC. Transmit/Receive Clock (input or output). This pin
functions under program control. /TRXC may supply the
receive clock or the transmit clock in the input mode or
supply the output of the digital phase-locked loop, the
crystal oscillator, the baud rate generator, or the transmit
clock in the output mode.
/RTXC. Receive/Transmit Clock (input). This pin functions
under program control. /RTXC may supply the receive
clock, the transmit clock, the clock for the baud rate
generator, or the clock for the digital phase-locked loop.
The receive clock may be 1, 16, 32, or 64 times the data
rate in asynchronous mode.
/CTS. Clear To Send (input, active Low). If this pin is
programmed as an “auto enable”, a Low on it enables the
EMSCC transmitter. If not programmed as an auto enable,
it can be used as a general-purpose input. This pin is
Schmitt-trigger buffered to accommodate slow rise-times.
The EMSCC detects transitions on this input and can
interrupt the processor on either logic level transition.
/DCD. Data Carrier Detect (input, active Low). This pin
functions as an EMSCC receiver enable when programmed
as an “auto enable”; otherwise it can be used as a generalpurpose input pin. The pin is Schmitt-trigger buffered to
accommodate slow rise-times. The EMSCC detects transitions on this pin and can interrupt the processor on either
logic level transition.
RXA1. Receive Data 1 (input). This input receives data for
ASCI channel 1.
TXA1. Transmit Data 1 (output). This output transmits data
from ASCI Channel 1.
24
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
PIN DESCRIPTIONS (Continued)
EMSCC Signals
/RTS. Request to Send (output, active Low). When the
Request to Send (RTS) bit in Write Register 5 is set, the
/RTS signal goes Low. When the RTS bit is reset in the
Asynchronous mode and auto enables is on, the signal
goes High after the transmitter is empty. In Synchronous
mode, or in Asynchronous mode with auto enables off, the
/RTS pin strictly follows the state of the RTS bit. Thus the pin
can be used as a general-purpose output. In a special
“AppleTalk” mode on the Z80185, the pin is under hardware control.
PIA13-10. Port 1, Bits 3-0 or CTC CLK/TRG3-0 (input/
output). These lines can be configured as inputs or outputs, or as the “clock/trigger” inputs of the four CTC
channels, on a bit-by-bit basis.
PIA27-20. Port 2, Data, or Bidirectional (input/output).
These lines can be configured as inputs or outputs on a bitby-bit basis when not used for Bidirectional Centronics
operation. However, when used for Bidirectional Centronics
operation, software and hardware controls the direction of
all eight as a unit.
Bidirectional Centronics Pins
/DTR. Data Terminal Ready (outputs, active Low). The
“/DTR//REQ” functionality found in other SCC family members has been reconfigured internal to the EMSCC
megacell. The /DTR output is routed to this pin, while the
/REQ signal is routed to the DMA request multiplexing
logic as described in a later section on the EMSCC. This
pin follows the state of the DTR bit in WR5 of the EMSCC.
Note: The /W/REQ pin present on other SCC family members has its two possible functions reconfigured internal to
the EMSCC, and both functions are handled internally to
the Z80185. The Wait output of the EMSCC drives the
/WAIT signal in a wire-ORed fashion with other internal and
external peripherals. The /REQ component is routed to the
DMA request multiplexing logic as described in a later
section on the EMSCC.
Z80185 Parallel Ports
PIA16-14. Port 1, Bits 6-4 or CTC ZC/TO2-0 (input/output).
These lines can be configured as inputs or outputs, or as
the “zero count/timeout” outputs of three of the four CTC
channels, on a bit-by-bit basis.
DS971850301
nStrobe, nAutoFd, nSelectIn, nInit (input/outputs). These
are inputs when using P27-20 for the Peripheral side of a
Centronics controller, or outputs when using P27-20 for the
Host side of such an interface. In certain P1284 modes,
these pins assume other names as described in the
section on the Centronics P1284 controller. When not
using P27-20 for a Centronics controller, these pins can be
used as general-purpose inputs or outputs.
Busy, nAck, PError, nFault, Select (input/outputs). These
are outputs when using P27-20 for the Peripheral side of a
Centronics P1284 controller, or inputs when using P27-20
for the Host side of such an interface. In certain P1284
modes, these pins have other names as described in the
section on the Centronics P1284 controller. When not
using P27-20 for a Centronics P1284 controller, these pins
can be used as general-purpose outputs or inputs. These
pins always function in the opposite direction of the preceding group.
25
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
System Control Signals
ST. Status (output, active High). This signal is used with the
/M1 and /HALT output to indicate the nature of each CPU
machine cycle.
/RESET. Reset Signal (input, active Low). /RESET signal is
used for initializing the Z80185 and other devices in the
system. It must be kept Low for at least three system clock
cycles.
IEI. Interrupt Enable Signal (input, active High). IEI is used
with IEO to form a priority daisy-chain when there are
external interrupt-driven Z80-compatible peripherals.
IEO. Interrupt Enable Output Signal (output, active High).
In an interrupt daisy-chain, IEO controls the interrupt of
external peripherals. IEO is active when IEI is 1 and the
CPU is not servicing an interrupt from the on-chip peripherals.
/IOCS. /IOCS decodes /IORQ, /M1, and as many address
lines as are necessary to ensure it is activated for an I/O
space access to any register in any block of eight registers
that does not contain any on-chip registers. Also included
in the decode is any programmed relocation of the “180
register set” in the ICR, and the “Decode High I/O” bit in the
System Configuration Register. If the “180 registers” aren’t
relocated, and “Decode High I/O” is 0, /IOCS is active from
address XX40 though XXD7, XXF8 through XXFF, and
NN00 through NN3F, where NN are non-zero. If the “180
registers” are not relocated and “Decode High I/O” is 1,
/IOCS is active from 0040 through 00D7, and 00F8 through
FFFF. /IOCS is active when an external master is in control
of the bus, as well as when the Z80185 processor has
control.
26
/RAMCS. RAM Chip Select (output, active Low). This
signal is driven Low for memory accesses at addresses
that fall between the values programmed into the RAMLBR
and RAMUBR registers. It is active when an external
master has control of the bus, as well as when the Z80185
processor is in control.
/ROMCS. ROM Chip Select (output, active Low). This
output is driven Low for memory accesses between the top
of on-chip ROM (if on-chip ROM is enabled) and the value
programmed into the ROMBR register. It is active when an
external master has control of the bus, as well as when the
Z80185 processor is in control.
XTAL. Crystal (input, active High). This pin functions as the
Crystal oscillator connection and should be left open if an
external clock is used instead of a crystal. The oscillator
input is not a TTL level (reference DC Characteristics
section).
EXTAL. External Clock/Crystal (input, active High). This
pin functions as a Crystal oscillator connection. An external clock can be input to the Z80185 on this pin when a
crystal is not used. This input is Schmitt-triggered.
PHI. System Clock (output, active High). This output is the
processor’s reference clock, and is provided for the use of
external logic. The frequency of this output may be equal
to, or one-half that of the crystal or input clock frequency,
depending on an internal register bit.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 MPU FUNCTIONAL DESCRIPTION
The Z80185 includes a Zilog Z8S180 MPU (Static Z80180
MPU). This allows software code compatibility with existing Z80/Z180 software code. The following is an overview
of the major functional units of the Z80185.
Clock Generator. This logic generates the system clock
from either an external crystal or clock input. The external
clock is divided by two, or one if programmed, and is
provided to both internal and external devices.
The MPU portion of the Z80185 is the Z8S180 core with
added features and modifications. The single-channel
EMSCC of the Z80185 is compatible with the Z85233
EMSCC and features additional enhancements for
LocalTalk and the demultiplexing of the /DTR//REQ and
/WT//REQ lines.
Bus State Controller. This logic performs all of the status
and bus control activity associated with both the CPU and
some on-chip peripherals. This includes wait state timing,
reset cycles, DRAM refresh, and DMA bus exchanges.
Architecture
The Z80185 combines a high performance CPU core with
a variety of system and I/O resources useful in a broad
range of applications. The CPU core consists of four
functional blocks:
■
■
■
■
Clock Generator
Bus State Controller (Dynamic Memory Refresh)
Memory Management Unit (MMU)
Central Processing Unit (CPU).
The integrated I/O resources make up the remaining
functional blocks:
■
■
■
■
■
■
■
■
■
Direct Memory Access (DMA control—two channels)
Asynchronous Serial Communications Controller
(ASCI, two channels)
Programmable Reload Timers (PRT, two channels)
Clocked Serial I/O
Channel (CSIO)
Enhanced Z85C30 (EMSCC)
Counter/Timer Channels (CTC)
Parallel I/O
Bidirectional Centronics Controller.
DS971850301
Interrupt Controller. This logic monitors and prioritizes
the variety of internal and external interrupts and traps to
provide the correct responses from the CPU. To maintain
compatibility with the Z80 CPU, three different interrupt
modes are supported.
Memory Management Unit. The MMU allows the user to
“map” the memory used by the CPU (logically only 64
Kbytes) into the 1 Mbyte addressing range supported by
the Z80185. The organization of the MMU object code
maintains compatibility with the Z80 CPU while offering
access to an extended memory space. This is accomplished by using an effective “common area-banked area”
scheme.
Central Processing Unit. The CPU is microcoded to
provide a core that is object-code compatible with the Z80
CPU. It also provides a superset of the Z80 instruction set,
including 8-bit multiply. This core has been modified to
allow many of the instructions to execute in fewer clock
cycles.
DMA Controller. The DMA controller provides high-speed
transfers between memory and I/O devices. Transfer operations supported are memory-to-memory, memory to or
from I/O, and I/O-to-I/O. Transfer modes supported are
request, burst, and cycle steal. DMA transfers can access
the full 1 Mbyte addressing range with a block length up to
64 Kbytes, and can cross over the 64 Kbytes boundaries.
27
/CTS0/RxS
CKA0/CKS
/INT2
/NMI
/RFSH
/BUSACK
/BUSREQ
/WAIT
/HALT
/IORQ
/MREQ
/M1
/WR
/RD
/INT1
Interrupt
CPU
16-Bit
Programmable
Reload Timers
(2)
DMACs
(2)
TOUT//DREQ
TxA0
Clocked
Serial I/O
Port
CKA0/CKS
Data Bus (8-Bit)
/RTS0/TxS
Bus State Control
Timing &
Clock
Generator
Address Bus (16-Bit)
TOUT/
/DREQ
/RESET
EXTAL
XTAL
Ø
/INT0
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Asynchronous
SCI
(Channel 0)
RxA0
/RTS0
/CTS0
/DCD0
TxA1
Asynchronous
SCI
(Channel 1)
MMU
A19-A0
DCD0/CKA1
RxA1
D7-D0
Figure 21. Z8S180 MPU Block Diagram
28
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
Z80185 MPU FUNCTIONAL DESCRIPTION (Continued)
DMA Controller
The two DMA channels of the Z80185 can transfer data to
or from the EMSCC channel, the parallel interface, the
async ports, or an external device. The I/O device encoding in SAR18-16 and DAR18-16 of the existing Z80180 is
modified as shown in Table 1.
DMA request signals between the various cells are handled
internally by the mechanisms described in this section,
and are not pinned-out, nor are the TEND termination
count outputs of the DMA channels.
Table 1. SAR18-16 and DAR18-16 I/O Device Encoding
SM1-0
SAR18-16
11
11
11
11
11
11
11
000
001
010
011
10X
1X0
111
Source
DM1-0
DAR18-16
11
11
11
11
11
11
11
000
001
010
011
10X
1X0
111
ext (TOUT/DREQ)
ASCI0 Rx
ASCI1 Rx
EMSCC Rx
Reserved, do not program.
PIA27-20 in
Destination
ext (TOUT/DREQ)
ASCI0 Tx
ASCI1 Tx
EMSCC Tx
Reserved, do not program.
PIA27-20 out
Asynchronous Serial Communications
Interface (ASCI)
The ASCI logic provides two individual full-duplex UARTs.
Each channel includes a programmable baud rate generator and modem control signals. The ASCI channels can
also support a multiprocessor communications format. For
ASCI0, up to three modem control signals and one clock
signal can be pinned out, while ASCI1 has a data-only
interface.
The receiver includes a 4-byte FIFO, plus a shift register as
shown in Figure 22.
During Reset and in I/O Stop state, and for ASCI0 if /DCD0
is auto-enabled and is High, an ASCI is forced to the
following conditions:
■
■
■
■
If DCD is not auto-enabled, the /DCD pin has no effect on
the FIFOs or enable bits.
Notes:
PE = Parity Error
FE = Framing Error
OR = Overrun
BK = Break
MP = Multiprocessor Bit
Error
Latches
Overrun
Error
4x4 Bit
Error
FIFO
FIFO Empty
All Error Bits Cleared (including those in the FIFO)
Receive Enable Cleared (cntla bit 6 = 0)
Transmit Enable Cleared (cntla bit 5 = 0).
MP
4-Byte
Bit Data FIFO
P F O B
E E R K
Error
Shift Register
RXA
Figure 22. ASCI Receiver
DS971850301
29
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
FIFO and Receiver Operation
Overrun Error
The 4-byte Receive FIFO is used to buffer incoming data
to reduce the incidence of overrun errors. When the RE bit
is set in the CNTLA register, the RXA pin is monitored for
a Low transition. One-half bit time after the Low transition
of the RXA pin, the ASCI samples RXA again. If it has gone
back to High, the ASCI ignores the previous Low transition
and resumes looking for a new one, but if RXA is still Low,
it considers this a start bit and proceeds to clock in the data
based upon the internal baud rate generator or the external CKA pin. The number of data bits, parity, multiprocessor and stop bits are selected by the MOD2, MOD1, MOD0
and MP bits in the CNTLA and CNTLB registers. After the
data has been received the appropriate MP, parity and
one stop bit are checked. Data and any errors are clocked
into the FIFOs during the stop bit. Interrupts, Receive Data
Register Full Flag, and DMA requests will also go active
during this time.
An overrun occurs if the receive FIFO is full when the
receiver has just assembled a byte in the shift register and
is ready to transfer it to the FIFO. If this occurs, the overrun
error bit associated with the previous byte in the FIFO is
set. The latest data byte is not transferred from the shift
register to the FIFO in this case, and is lost. Once an
overrun occurs, the receiver does not place any further
data in the FIFO, until the “last good byte received” has
come to the top of the FIFO so that the Overrun latch is set,
and software then clears the Overrun latch. Assembly of
bytes continues in the shift register, but this data is ignored
until the byte with the overrun error reaches the top of the
FIFO and is cleared with a write of 0 to the EFR bit.
Error Condition Handling
When the receiver places a data character in the Receive
FIFO, it also places any associated error conditions in the
error FIFO. The outputs of the error FIFO go to the set inputs
of the software-accessible error latches. Writing a 0 to
CNTLA EFR is the only way to clear these latches. In other
words, when an error bit reaches the top of the FIFO, it sets
an error latch. If the FIFO has more data and the software
reads the next byte out of the FIFO, the error latch remains
set, until the software writes a 0 to the EFR bit. The error bits
are cumulative, so if additional errors are in the FIFO, they
will set any unset error latches as they reach the top.
Break Detect
A Break is defined as a framing error with the data equal to
all zeros. When a break occurs, the all-zero byte with its
associated error bits are transferred to the FIFO, if it is not
full. If the FIFO is full, an overrun is generated, but the
break, framing error and data, are not transferred to the
FIFO. Any time a break is detected, the receiver will not
receive any more data until the RXA pin returns to a High
state. If the channel is set in multiprocessor mode and the
MPE bit of the CNTLA register is set to 1, then breaks,
errors and data will be ignored unless the MP bit in the
transmission is a 1. Note: The two conditions listed above
could cause a break condition to be missed if the FIFO is
full and the break occurs, or if the MP bit in the transmission
is not a 1 with the conditions specified above.
Parity and Framing Errors
Parity and Framing Errors do not affect subsequent receiver operation.
30
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 MPU FUNCTIONAL DESCRIPTION (Continued)
Baud Rate Generator
The Baud Rate Generator (BRG) has two modes. The first
is the same as in the Z80180. The second is a 16-bit down
counter that divides the processor clock by the value in a
16-bit time constant register, and is identical to the EMSCC
BRG. This allows a common baud rate of up to 512 Kbps
to be selected. The BRG can also be disabled in favor of
an external clock on the CKA pin.
The Receiver and Transmitter will subsequently divide the
output of the BRG (or the signal from the CKA pin) by 1, 16
or 64, under the control of the DR bit in the CNTLB register,
and the X1 bit in the ASCI Extension Control Register. To
compute baud rate, use the following formulas.
The ASCIs require a 50 percent duty cycle when CKA is
used as an input. Minimum High and Low times on CKA0
are typical of most CMOS devices.
RDRF is set, and if enabled an Rx Interrupt or DMA
Request is generated, when the receiver transfers a character from the Rx Shift Register to the Rx FIFO. The FIFO
merely provides margin against overruns. When there’s
more than one character in the FIFO, and software or a
DMA channel reads a character, RDRF either remains set
or is cleared and then immediately set again. For example,
if a receive interrupt service routine doesn’t read all the
characters in the RxFIFO, RDRF and the interrupt request
remain asserted.
If ss2,1,0 = 111, baud rate = fCKA / Clock mode
else if BRG mode baud rate = fPHI / (2 * (TC+2) * Clock
mode)
else baud rate = fPHI / ((10 + 20*PS) * 2^ss * Clock mode)
The Rx DMA request is disabled when any of the error flags
PE or FE or OVRN are set, so that software can identify with
which character the problem is associated.
TC = (fPHI / (2 * baud rate * Clock mode)) - 2
If Bit 7, RDRF Interrupt Inhibit, is set to 1 (see Figures 32
and 33), the ASCI does not request a Receive interrupt
when its RDRF flag is 1. Set this bit when programming a
DMA channel to handle the receive data from an ASCI. The
other causes for an ASCI Receive interrupt (PE, FE, OVRN,
and for ASCI0, DCD) continue to request Rx interrupt if the
RIE bit is 1. (The Rx DMA request is inhibited if PE or FE or
OVRN is set, so that software can tell where an error
occurred.) When this bit is 0, as it is after a Reset, RDRF will
cause an ASCI interrupt if RIE is 1.
Clock mode depends on bit 4 in ASEXT and bit 3 in CNTLB:
Programmable Reload Timer (PRT)
Where:
BRG mode is bit 3 of the ASEXT register
PS is bit 5 of the CNTLB register
TC is the 16-bit value in the ASCI Time Constant registers
The TC value for a given baud rate is:
X1
DR
0
0
1
1
0
1
0
1
Clock Mode
=
=
=
=
16
64
1
Reserved, do not use.
2^ss depends on the three LS bits of the CNTLB register:
ss2
ss1
ss0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
DS971850301
2^ss
=
=
=
=
=
=
=
=
1
2
4
8
16
32
64
External Clock from CKA0
(see above).
This logic consists of two separate channels, each containing a 16-bit counter (timer) and count reload register.
The time base for the counters is derived from the system
clock (divided by 20) before reaching the counter. PRT
channel 1 provides an optional output to allow for waveform generation.
The TOUT output of PRT1 is available on a multiplexed pin.
Clocked Serial I/O (CSIO)
The pins for this function are multiplexed with the RTS,
CTS, and clock pins for ASCI0. Note: It is possible to use
both ASCI0 and the CSIO at the same time. If bit 4 of the
System Configuration Register is set to 1, the CKS clock
signal will internally drive the clock for ASCI0 instead of the
system clock.
31
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
/M1
32K x 8 On-Chip Read-Only Memory (ROM)
The /M1 generation logic of the Z80180 allows the use of
logic analyzer disassemblers that rely on /M1 identifying
the start of each instruction. If the MIE bit is set to 1, the
processor does not refetch an RETI instruction.
The Z80185 processor features 32K x 8 of masked ROM.
This on-chip ROM allows zero-wait-state generation at the
maximum clock rate. The Z80195 processor is ROMless.
Z80185 On-Chip ROM Enable/Disable
Z80185 Counter/Timers
These facilities include two 16-bit Programmable Reload
Timers (PRTs) like those provided in the Z80180 and its
successors, plus four CTC channels like those in the
Z84C30. The TOUT output of PRT1 is output on a multiplexed pin, and the ZC/TO outputs and CLK/TRG inputs of
the CTC’s are multiplexed with PIA17-10 on an individual
basis, rather than simultaneously as on the Z80181. Internal cascading is provided between the CTCs, as described in CTC Control section.
Z80185 I/O Chip Select
If /WAIT is Low at the rising edge of /RESET, the on-chip
program memory is disabled and all accesses to addresses below the upper limit of /ROMCS go off-chip. This
feature allows code development and emulation using
external devices before the user is ready to use on-chip
memory.
If /WAIT is High at the rising edge of /RESET, accesses to
addresses below both the size of on-chip ROM and the
upper limit of /ROMCS, the user should select on-chip
ROM. Accesses that are above the size of the on-chip
ROM, but below the upper limit of /ROMCS, go off-chip with
/ROMCS asserted.
This output is active when an external master has control
of the bus, as well as when the Z80185 processor has
control. The /IOCS output of the Z80185 operates correctly
if the "180 registers" are relocated to I/O address 40-7F or
80-BF, and takes into account the "Decode High I/O" bit in
the Z80185 System Configuration Register.
Table 2. Power Down Modes
Power-Down
Modes
CPU
Core
On-Chip
I/O
OSC.
CLKOUT
Recovery
Source
Recovery Time
(Minimum)
SLEEP
I/O STOP
SYSTEM STOP
IDLE †
STANDBY†
Stop
Running
Stop
Stop
Stop
Running
Stop
Stop
Stop
Stop
Running
Running
Running
Running
Stop
Running
Running
Running
Stop
Stop
RESET, Interrupts
By Programming
RESET, Interrupts
RESET, Interrupts, BUSREQ
RESET, Interrupts, BUSREQ
1.5 Clock
1.5 Clock
8 +1.5 Clock
217 +1.5 Clock (Normal Recovery)
26 +1.5 Clock (Quick Recovery)
32
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z8S180 POWER-DOWN MODES
The following is a detailed description of the enhancements to the Z8S180 from the standard Z80180 in the areas
of STANDBY, IDLE, and STANDBY-QUICK RECOVERY
modes.
Add-On Features
There are five different power-down modes. SLEEP and
SYSTEM STOP are inherited from the Z80180. In SLEEP
mode, the CPU is in a stopped state while the on-chip
I/Os are still operating. In I/O STOP mode, the on-chip I/Os
are in a stopped state while leaving the CPU running. In
SYSTEM STOP mode, both the CPU and the on-chip I/Os
are in the stopped state to reduce current consumption.
The Z8S180 has added two additional power-down modes,
STANDBY and IDLE, to reduce current consumption even
further. The differences in these power-down modes are
summarized in Table 2.
Notes:
†
IDLE and STANDBY modes are only offered in the Z8S180. Note that the
minimum recovery time can be achieved if INTERRUPT is used as the
Recovery Source.
STANDBY Mode
The Z8S180 is designed to save power. Two low-power
programmable power-down modes have been added:
STANDBY mode and IDLE mode. The STANDBY/IDLE
mode is selected by multiplexing D6 and D3 of the CPU
Control Register (CCR, I/O Address = 1FH).
To enter STANDBY mode:
oscillator stabilization. When the part receives an external
IRQ or BUSREQ during STANDBY mode, the oscillator is
restarted and the timer counts down 217 counts before
acknowledgment is sent to the interrupt source.
The recovery source needs to remain asserted for the
duration of the 217 count, otherwise standby will be re-
1. Set D6 and D3 to 1 and 0, respectively.
2. Set the I/O STOP bit (D5 of ICR,
I/O Address = 3FH) to 1.
3. Execute the SLEEP instruction.
When the device is in STANDBY mode, it behaves similar
to the SYSTEM STOP mode as it exists on the Z80180,
except that the STANDBY mode stops the external oscillator, internal clocks and reduces power consumption to
50 µA (typical).
Since the clock oscillator has been stopped, a restart of
the oscillator requires a period of time for stabilization. An
18-bit counter has been added in the Z8S180 to allow for
DS971850301
33
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
STANDBY Mode Exit with BUS REQUEST
Optionally, if the BREXT bit (D5 of CPU Control Register) is
set to 1, the Z8S180 exits STANDBY mode when the
/BUSREQ input is asserted; the crystal oscillator is then
restarted. An internal counter automatically provides time
for the oscillator to stabilize, before the internal clocking
and the system clock output of the Z8S180 are resumed.
1. Exit with Non-Maskable Interrupts
The Z8S180 relinquishes the system bus after the clocking
is resumed by:
If an External Maskable Interrupt input is asserted, the CPU
responds according to the status of the Global Interrupt
Enable Flag IEF1 (determined by the ITE1 bit) and the
settings of the corresponding interrupt enable bit in the
Interrupt/Trap Control Register (ITC: I/O Address = 34H):
■ Tri-State the address outputs A19 through A0.
If /NMI is asserted, the CPU begins a normal NMI interrupt
acknowledge sequence after clocking resumes.
2. Exit with External Maskable Interrupts
■ Tri-State the bus control outputs /MREQ, /IORQ,
/RD and /WR.
■ Asserting /BUSACK
The Z8S180 regains the system bus when /BUSREQ is
deactivated. The address outputs and the bus control
outputs are then driven High; the STANDBY mode is
exited.
If the BREXT bit of the CPU Control Register (CCR) is
cleared, asserting the /BUSREQ will not cause the Z8S180
to exit STANDBY mode.
If STANDBY mode is exited due to a reset or an external
interrupt, the Z8S180 remains relinquished from the system bus as long as /BUSREQ is active.
a. If an interrupt source is disabled in the ITC, asserting
the corresponding interrupt input will not cause the
Z8S180 to exit STANDBY mode. This is true regardless
of the state of the Global Interrupt Enable Flag IEF1.
b. If the Global Interrupt Flag IEF1 is set to 1, and if an
interrupt source is enabled in the ITC, asserting the
corresponding interrupt input causes the Z8S180 to
exit STANDBY mode. The CPU performs an interrupt
acknowledge sequence appropriate to the input being asserted when clocking is resumed if:
■
The interrupt input follows the normal
interrupt daisy-chain protocol.
■
The interrupt source is active until the
acknowledge cycle is completed.
STANDBY Mode Exit with External Interrupts
STANDBY mode can be exited by asserting input /NMI.
The STANDBY mode may also exit by asserting /INT0,
/INT1 or /INT2, depending on the conditions specified in
the following paragraphs.
/INT0 wake-up requires assertion throughout duration of
clock stabilization time (217 clocks).
If exit conditions are met, the internal counter provides time
for the crystal oscillator to stabilize, before the internal
clocking and the system clock output within the Z8S180
are resumed.
34
c. If the Global Interrupt Flag IEF1 is disabled, in other
words, reset to 0, and if an interrupt source is enabled
in the ITC, asserting the corresponding interrupt input
will still cause the Z8S180 to exit STANDBY mode. The
CPU will proceed to fetch and execute instructions
that follow the SLEEP instruction when clocking is
resumed.
If the External Maskable Interrupt input is not active until
clocking resumes, the Z8S180 will not exit STANDBY
mode. If the Non-Maskable Interrupt (/NMI) is not active
until clocking resumes, the Z8S180 still exits the STANDBY
mode even if the interrupt sources go away before the
timer times out, because /NMI is edge-triggered. The
condition is latched internally once /NMI is asserted Low.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
IDLE Mode
Standby-Quick Recovery Mode
IDLE mode is another power-down mode offered by the
Z8S180. To enter IDLE mode:
STANDBY-QUICK RECOVERY mode is an option offered
in STANDBY mode to reduce the clock recovery time in
STANDBY mode from 217 clock cycles (6.5 ms at 20 MHz)
to 26 clock cycles (3.2 µs at 20 MHz). This feature can only
be used when providing an oscillator as clock source.
1. Set D6 and D3 to 0 and 1, respectively.
2. Set the I/O STOP bit (D5 of ICR,
I/O Address = 3FH) to 1.
To enter STANDBY-QUICK RECOVERY mode:
3. Execute the SLEEP instruction.
1. Set D6 and D3 to 1 and 1, respectively.
When the part is in IDLE mode, the clock oscillator is kept
oscillating, but the clock to the rest of the internal circuit,
including the CLKOUT, is stopped completely. IDLE mode
is exited in a similar way as STANDBY mode, in other
words, RESET, BUS REQUEST or EXTERNAL INTERRUPTS, except that the 217 bit wake-up timer is bypassed;
all control signals are asserted eight clock cycles after the
exit conditions are gathered.
2. Set the I/O STOP bit (D5 of ICR,
I/O Address = 3FH) to 1.
3. Execute the SLEEP instruction.
When the part is in STANDBY-QUICK RECOVERY mode,
the operation is identical to STANDBY mode except when
exit conditions are gathered, in other words, RESET, BUS
REQUEST or EXTERNAL INTERRUPTS. The clock and
other control signals are recovered sooner than the
STANDBY mode.
Note: If STANDBY-QUICK RECOVERY is enabled, the
user must make sure stable oscillation is obtained within
64 clock cycles.
DS971850301
35
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Z8S180 MPU REGISTER MAP
Notes:
Registers listed in boldface type represent new registers added to the Z8S180.
All register addresses not listed are Reserved.
Register Name
I/O Addr/Access
Register Name
I/O Addr/Access
ASCI Control Register A Ch 0
ASCI Control Register A Ch 1
ASCI Control Register B Ch 0
ASCI Control Register B Ch 1
ASCI Status Register Ch 0
ASCI Status Register Ch 1
ASCI TX Data Register Ch 0
ASCI TX Data Register Ch 1
ASCI RX Data Register Ch 0
ASCI RX Data Register Ch 1
CSIO Control Register
CSIO Transmit/Receive Data Reg.
Timer Data Register Ch OL
Timer Data Register Ch OH
Reload Register Ch OL
Reload Register Ch OH
Timer Control Register
ASCI0 Extension Control Reg.
ASCI1 Extension Control Reg.
Timer Data Register Ch 1L
Timer Data Register Ch 1H
Timer Reload Register Ch 1L
Timer Reload Register Ch 1H
Free Running Counter
ASCI0 Time Constant Low
ASCI0 Time Constant High
ASCI1 Time Constant Low
ASCI1 Time Constant High
%0000/40/80 R/W
%0001/41/81 R/W
%0002/42/82 R/W
%0003/43/83 R/W
%0004/44/84 R/W
%0005/45/85 R/W
%0006/46/86 R/W
%0007/47/87 R/W
%0008/48/88 R/W
%0009/49/89 R/W
%000A/4A/8A R/W
%000B/4B/8B R/W
%000C/4C/8C R/W
%000D/4D/8D R/W
%000E/4E/8E R/W
%000F/4F/8F R/W
%0010/50/90
%0012/52/92 R/W
%0013/53/93 R/W
%0014/54/94 R/W
%0015/55/95 R/W
%0016/56/96 R/W
%0017/57/97 R/W
%0018/58/98 R/W
%001A/5A/9A R/W
%001B/5B/9B R/W
%001C/5C/9C R/W
%001D/5D/9D RW
CPU Control Register
DMA Source Addr Register Ch OL
DMA Source Addr Register Ch OH
DMA Source Addr Register Ch OB
DMA Dest Addr Register Ch OL
DMA Dest Addr Register Ch OH
DMA Dest Addr Register Ch OB
DMA Byte Count Register Ch OL
DMA Byte Count Register Ch OH
DMA Memory Addr Register Ch 1L
DMA Memory Addr Register Ch 1H
DMA Memory Addr Register Ch 1B
DMA I/O Addr Register Ch 1L
DMA I/O Addr Register Ch 1H
DMA I/O Addr Register Ch 1B
DMA Byte Count Register Ch 1L
DMA Byte Count Register Ch 1H
DMA Status Register
DMA Mode Register
DMA/WAIT Control Register
IL Register
INT/TRAP Control Register
Refresh Control Register
MMU Common Base Register
MMU Bank Base Register
MMU Common/Bank Area Register
Operation Mode Control Register
I/O Control Register
%001F/5F/9F R/W
%0020/60/A0 R/W
%0021/61/A1 R/W
%0022/62/A2 R/W
%0023/63/A3 R/W
%0024/64/A4 R/W
%0025/65/A5 R/W
%0026/66/A6 R/W
%0027/67/A7 R/W
%0028/68/A8 R/W
%0029/69/A9 R/W
%002A/6A/AA R/W
%002B/6B/AB R/W
%002C/6C/AC R/W
%002D/6D/AD R/W
%002E/6E/AE R/W
%002F/6F/AF R/W
%0030/70/B0 R/W
%0031/71/B1 R/W
%0032/72/B2 R/W
%0033/73/B3 R/W
%0034/74/B4 R/W
%0036/76/B6 R/W
%0038/78/B8 R/W
%0039/79/B9 R/W
%003A/7A/BA R/W
%003E/7E/BE R/W
%003F/7F/BF R/W
36
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
Z8S180 MPU REGISTERS
ASCI CHANNELS CONTROL REGISTERS
CNTLA0
Bit
Addr 00H
MPBR/
MOD2 MOD1 MOD0
EFR
MPE
RE
TE
/RTS0
0
0
0
1
x
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Upon RESET
R/W
MODE Selection
Start + 7-Bit Data + 1 Stop
Start + 7-Bit Data + 2 Stop
Start + 7-Bit Data + Parity + 1 Stop
Start + 7-Bit Data + Parity + 2 Stop
Start + 8-Bit Data + 1 Stop
Start + 8-Bit Data + 2 Stop
Start + 8-Bit Data + Parity + 1 Stop
Start + 8-Bit Data + Parity + 2 Stop
Read - Multiprocessor Bit Receive
Write - Error Flag Reset
Request To Send
Transmit Enable
Receive Enable
Multiprocessor Enable
Figure 23a. ASCI Control Register A (Ch. 0)
Addr 01H
CNTLA1
Bit
Upon RESET
R/W
MPE
RE
TE
CKA1D MPBR/ MOD2 MOD1 MOD0
EFR
0
0
0
1
x
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
MODE Selection
Start + 7-Bit Data + 1 Stop
Start + 7-Bit Data + 2 Stop
Start + 7-Bit Data + Parity + 1 Stop
Start + 7-Bit Data + Parity + 2 Stop
Start + 8-Bit Data + 1 Stop
Start + 8-Bit Data + 2 Stop
Start + 8-Bit Data + Parity + 1 Stop
Start + 8-Bit Data + Parity + 2 Stop
Read - Multiprocessor Bit Receive
Write - Error Flag Reset
CKA1 Disable
Transmit Enable
Receive Enable
Multiprocessor Enable
Figure 23b. ASCI Control Register A (Ch. 1)
DS971850301
37
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Addr 02H
CNTLB0
/CTS/
PS
Bit
MPBT
Upon Reset
Invalid
0
†
0
0
1
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MP
PE0
DR
SS2
SS1
SS0
Clock Source and Speed Select
Divide Ratio
Parity Even or Odd
Clear To Send/Prescale
Multiprocessor
Multiprocessor Bit Transmit
† /CTS - Depending on the condition of /CTS pin.
PS - Cleared to 0.
General
Divide Ratio
SS, 2, 1, 0
000
001
010
011
100
101
110
111
PS = 0
(Divide Ratio = 10)
DR = 0 (x16)
PS = 1
(Divide Ratio = 30)
DR = 1 (x64)
Ø ÷ 160
Ø÷
Ø ÷ 320
Ø÷
Ø ÷ 640
Ø÷
Ø ÷ 1280
Ø÷
Ø ÷ 2560
Ø÷
Ø ÷ 5120
Ø÷
Ø ÷ 10240
Ø÷
External Clock (Frequency < Ø)
640
1280
2560
5120
10240
20480
40960
DR = 0 (x16)
DR = 1 (x64)
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
480
960
1920
3840
7680
15360
30720
1920
3840
7680
15360
30720
61440
122880
Figure 24. ASCI Control Register B (Ch. 0)
38
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
ASCI CHANNELS CONTROL REGISTERS (Continued)
Addr 03H
CNTLB1
/CTS/
PS
Bit
MPBT
MP
Upon Reset
Invalid
0
0
0
0
1
1
1
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
PE0
DR
SS2
SS1
SS0
Clock Source and Speed Select
Divide Ratio
Parity Even or Odd
Read - Status of /CTS pin
Write - Select PS
Multiprocessor
Multiprocessor Bit Transmit
General
Divide Ratio
SS, 2, 1, 0
000
001
010
011
100
101
110
111
PS = 0
(Divide Ratio = 10)
DR = 0 (x16)
DR = 1 (x64)
Ø ÷ 160
Ø÷
Ø ÷ 320
Ø÷
Ø ÷ 640
Ø÷
Ø ÷ 1280
Ø÷
Ø ÷ 2560
Ø÷
Ø ÷ 5120
Ø÷
Ø ÷ 10240
Ø÷
External Clock (Frequency < Ø)
640
1280
2560
5120
10240
20480
40960
PS = 1
(Divide Ratio = 30)
DR = 0 (x16)
DR = 1 (x64)
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
Ø÷
480
960
1920
3840
7680
15360
30720
1920
3840
7680
15360
30720
61440
122880
Figure 25. ASCI Control Register B (Ch. 1)
DS971850301
39
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Addr 04H
STAT0
Bit
RDRF OVRN
PE
FE
RIE
/DCD0 TDRE
TIE
Upon Reset
0
0
0
0
0
†
††
0
R/W
R
R
R
R
R/W
R
R
R/W
Transmit Interrupt Enable
Transmit Data Register
Empty
Data Carrier Detect
Receive Interrupt Enable
Framing Error
Parity Error
Over Run Error
Receive Data Register Full
† /DCD0 - Depending on the condition of /DCD0 Pin.
†† /CTS0 Pin
TDRE
L
H
1
0
Figure 26. ASCI Status Register (Ch. 0)
Addr 05H
STAT1
Bit
RDRF OVRN
PE
FE
RIE CTS1E TDRE
TIE
Upon Reset
0
0
0
0
0
0
1
0
R/W
R
R
R
R
R/W
R/W
R
R/W
Transmit Interrupt Enable
Transmit Data Register
Empty
Reserved
Receive Interrupt Enable
Framing Error
Parity Error
Over Run Error
Receive Data Register Full
Figure 27. ASCI Status Register (Ch. 1)
40
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
ASCI CHANNELS CONTROL REGISTERS (Continued)
TDR0
Write Only
7
6
5
Addr 06H
4
3
2
1
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
New Z8S180 Register
0
Send Break
0 = Normal Xmit
1 = Drive TXA Low
Transmit Data
Break Detect (RO)
Figure 28. ASCI Transmit Data Register (Ch. 0)
Break Feature Enable
BRG0 Mode
0 = As S180
1 = Enable 16-bit BRG counter
TDR1
Write Only
7
6
X1 bit clk ASCI0
0 = CKA0 /16 or /64
1 = CKA0 is bit clock
Addr 07H
5
4
3
2
1
0
CTS0 Disable
0 = CTS0 Auto-Enable Tx
1 = CTS0 Advisory to SW
Transmit Data
DCD0 Disable
0 = DCD0 Auto-Enables Rx
1 = DCD0 Advisory to SW
Figure 29. ASCI Transmit Data Register (Ch. 1)
RDRF Interrupt Inhibit
TSR0
Read Only
x
x
x
Figure 32. ASCI0 Extension Control Register
(I/O Address 12)
Addr 08H
x
x
x
x
x
Received Data
Figure 30. ASCI Receive Data Register (Ch. 0)
x
x
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
New Z8S180 Register
Send Break
0 = Normal Xmit
1 = Drive TXA Low
TSR1
Read Only
x
7
Addr 09H
x
x
x
x
Break Detect (RO)
x
Break Feature Enable
Received Data
Figure 31. ASCI Receive Data Register (Ch. 1)
BRG1 Mode
0 = As S180
1 = Enable 16-bit BRG Counter
X1 Bit CLK ASCI1
0 = CKA1 /16 or /64
1 = CKA1 is bit Clock
Reserved (Program as 0)
RDRF Interrupt Inhibit
Figure 33. ASCI1 Extension Control Register
(I/O Address 13)
DS971850301
41
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
ACSI TIME CONSTANT REGISTERS
New Z8S180 Registers
7
6
Register:
Address:
7
6
Register:
Address:
5
4
3
2
1
0
7
ASCI0 Time Constant Low
1Ah
5
4
3
2
1
6
Register:
Address:
0
7
ASCI0 Time Constant High
1Bh
6
Register:
Address:
5
4
3
2
1
0
ASCI1 Time Constant Low
1Ch
5
4
3
2
1
0
ASCI1 Time Constant High
1Dh
CSI/O REGISTERS
CNTR
Bit
Upon Reset
R/W
EF
0
R
Addr 0AH
EIE
0
R/W
RE
0
R/W
TE
0
R/W
SS2
1
R/W
1
SS1
1
R/W
SS0
1
R/W
Speed Select
Transmit Enable
Receive Enable
End Interrupt Enable
End Flag
SS2, 1, 0
Baud Rate
SS2, 1, 0
Baud Rate
000
001
010
011
Ø÷
Ø÷
Ø÷
Ø÷
100
101
110
111
Ø ÷ 320
Ø ÷ 640
Ø ÷ 1280
External Clock
(Frequency < Ø ÷ 20)
20
40
80
100
Figure 34. CSI/O Control Register
TRDR
Read/Write
7
6
5
Addr 0BH
4
3
2
1
0
Read - Received Data
Write - Transmit Data
Figure 35. CSI/O Transmit/Receive Data Register
42
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
TIMER DATA REGISTERS
TMDR0L
Read/Write
7 6 5 4
3
Addr 0CH
2 1 0
Figure 36. Timer 0 Data Register L
6
5
Addr 0DH
15 14 13 12 11 10 9
8
When Read, read Data Register L
before reading Data Register H.
Figure 38. Timer 0 Data Register H
TMDR1L
Read/Write
7
TMDR0H
Read/Write
4
3
Addr 14H
2 1 0
Figure 37. Timer 1 Data Register L
TMDR1H
Read/Write
Addr 15H
15 14 13 12 11 10 9
8
When Read, read Data Register L
before reading Data Register H.
Figure 39. Timer 1 Data Register H
TIMER RELOAD REGISTERS
RLDR0L
Read/Write
7
6
5
4
3
Addr 0EH
RLDR0H
Read/Write
2
15 14 13 12 11 10 9
1
0
Figure 40. Timer 0 Reload Register L
RLDR1L
Read/Write
7
6
5
Addr 16H
4
3
2
1
0
Figure 41. Timer 1 Reload Register L
DS971850301
Addr 0FH
8
Figure 42. Timer 0 Reload Register H
RLDR1H
Read/Write
Addr 17H
15 14 13 12 11 10 9 8
Figure 43. Timer 1 Reload Register H
43
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
TIMER CONTROL REGISTER
Addr 10H
TCR
Bit
Upon Reset
R/W
TIF1 TIF0 TIE1 TIE0 TOC1 TOC0 TDE1 TDE0
0
0
0
0
0
0
0
0
R
R
R/W
R/W
R/W
R/W
R/W
R/W
Timer Down Count Enable 1,0
Timer Output Control 1,0
Timer Interrupt Enable 1,0
Timer Interrupt Flag 1,0
TOC1,0 A15/TOUT
00
Inhibited
01
Toggle
10
0
11
1
Figure 44. Timer Control Register
FREE RUNNING COUNTER
FRC
Read Only
7
6
Addr 18H
5
4
3
2
1
0
Figure 45. Free Running Counter
CPU CONTROL REGISTER
CPU Control Register (CCR) Addr 1FH
D7 D6 D5 D4 D3 D2 D1 D0
0
0
0
0
0
0
0
0
Figure 46. CPU Control Register
Note: See Figure 87 for full description.
44
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
DMA REGISTERS
SAR0L
Read/Write
SA7
Addr 20H
SA0
DAR0L
Read/Write
DA7
Addr 23H
DA0
SAR0H
Read/Write
SA15
Addr 21H
SA8
DAR0H
Read/Write
DA15
Addr 24H
DA8
SAR0B
Read/Write
-
-
-
Addr 22H
SA16
SA19
-
-
Bits 0-3 are used for SAR0B
SM1-0
SAR18-16
11
11
11
11
11
000
001
010
011
111
Source
ext (TOUT/DREQ)
ASCI0 Rx
ASCI1 Rx
ESCC Rx
PIA27-20 IN
Figure 47. DMA 0 Source Address Registers
DS971850301
DAR0B
Read/Write
-
-
Addr 25H
DA19 DA16
-
Bits 0-3 are used for DAR0B
DM1-0
DAR18-16
11
11
11
11
11
000
001
010
011
111
Destination
ext (TOUT/DREQ)
ASCI0 Tx
ASCI1 Tx
ESCC Tx
PIA27-20 OUT
Figure 48. DMA 0 Destination Address Registers
45
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
BCR0L
Read/Write
BC7
Addr 26H
BC0
MAR1L
Read/Write
MA7
Addr 28H
MA0
BCR0H
Read/Write
BC15
Addr 27H
BC8
MAR1H
Read/Write
MA15
Addr 29H
MA8
Figure 49. DMA 0 Byte Counter Registers
MAR1B
Read/Write
MA19
-
-
-
Addr 2AH
MA16
-
Figure 50. DMA 1 Memory Address Registers
IAR1B
D7
D6
Addr 2D
D5
D4
D3
D2
D1
D0
New Z8S180 Register
000
001
010
011
111
=
=
=
=
=
DMA1 ext TOUT/DREQ
DMA1 ASCI0
DMA1 ASCI1
DMA1 ESCC
DMA1 PIA27-20 (P1284)
0 = TOUT//DREQ is DREQ In
1 = TOUT//DREQ is TOUT Out
Reserved, program as 0.
Currently selected DMA
Channel when Bit 7 = 1
Alternating Channels
0 = DMA Channels
are independent
1 = Toggle between DMA
channels for same device
Figure 51. DMA I/O Address Register Ch. 1
46
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
DMA REGISTER DESCRIPTION
Bit 7. This bit should be set to 1 only when both DMA
channels are set to take their requests from the same
device. If this bit is 1 (it resets to 0), the channel end output
of DMA channel 0 sets a flip-flop, so that thereafter the
device’s request is visible to channel 1, but is not visible to
channel 0. The channel end output of channel 1 clears the
FF, so that thereafter, the device’s request is visible to
channel 0, but not visible to channel 1.
Bit 6. When both DMA channels are programmed to take
their requests from the same device, this bit (FF mentioned
in the previous paragraph) controls which channel the
device’s request is presented to: 0 = DMA 0, 1 = channel
1. When bit 7 is 1, this bit is automatically toggled by the
channel end output of the channels, as described above.
Bits 5-4. Reserved and should be programmed as 0.
Bits 3. This bit controls the direction and use of the TOUT/
DREQ pin. When it’s 0, TOUT/DREQ is the DREQ input;
when it’s 1, TOUT/DREQ is an output that can carry the
TOUT signal from PRT1, if PRT1 is so programmed.
IAR1L
Read/Write
IA7
Bits 2-0. With “DIM1”, bit 1 of DCNTL, these bits control
which request is presented to DMA channel 1, as follows:
DIM1 IAR18-16
Request Routed to DMA Channel 1
0
0
0
0
0
0
0
000
001
010
011
10X
1X0
111
ext TOUT/DREQ
ASCI0 Tx
ASCI1 Tx
EMSCC out
Reserved, do not program.
Reserved, do not program.
PIA27-20 out
1
1
1
1
1
1
1
000
001
010
011
10X
1X0
111
ext TOUT/DREQ
ASCI0 Rx
ASCI1 Rx or TOUT//DREQ pin
EMSCC in
Reserved, do not program.
Reserved, do not program.
PIA27-20 in
BCR1L
Read/Write
BC7
Addr 2EH
BC0
BCR1H
Read/Write
BC15
Addr 2FH
BC8
Addr 2BH
IA0
IAR1H
Read/Write
IA15
Addr 2CH
IA8
Figure 53. DMA 1 Byte Count Registers
Figure 52. DMA I/O Address Registers
DSTAT
Bit
Upon Reset
R/W
DE1
0
R/W
DE0 /DWE1 /DWE0 DIE1
0
1
1
0
R/W
W
W
R/W
DIE0
0
R/W
Addr 30H
DIME
1
0
R
-
DMA Master Enable
DMA Interrupt Enable 1, 0
DMA Enable Bit Write Enable 1, 0
DMA Enable Ch 1, 0
Figure 54. DMA Status Register
DS971850301
47
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
DMA REGISTERS (Continued)
DMODE
Bit
Upon Reset
Addr 31H
-
-
DM1
1
1
0
0
0
0
R/W
R/W
R/W
R/W
R/W
DM0
SM1
SM0
MMOD
-
0
1
R/W
Memory MODE Select
Ch 0 Source Mode 1, 0
Ch 0 Destination Mode 1, 0
DM1, 0
00
01
10
11
MMOD
0
1
Destination
M
M
M
I/O
Address
DAR0+1
DAR0-1
DAR0 Fixed
DAR0 Fixed
SM1, 0
00
01
10
11
Source
M
M
M
I/O
Address
SAR0+1
SAR0-1
SAR0 Fixed
SAR0 Fixed
Mode
Cycle Steal Mode
Burst Mode
Figure 55. DMA Mode Registers
48
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
DMA REGISTERS (Continued)
DCNTL
Bit
Upon Reset
R/W
Addr 32H
MWI1 MWI0
IWI1
IWI0
DMS1 DMS0
DIM1
DIM0
1
1
1
1
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
DMA Ch 1 I/O Memory
Mode Select
/DREQi Select, i = 1, 0
I/0 Wait Insertion
Memory Wait Insertion
*
MWI1, 0
No. of Wait States
IWI1, 0
No. of Wait States
00
01
10
11
0
1
2
3
00
01
10
11
1
2
3
4
DMSi
Sense
1
0
Edge Sense
Level Sense
DM1, 0
Transfer Mode
00
01
10
11
M - I/O
M - I/O
I/O - M
I/O - M
Address Increment/Decrement
MAR1+1
MAR1-1
IAR1 Fixed
IAR1 Fixed
IAR1 Fixed
IAR1 Fixed
MAR1+1
MAR1-1
Note:
* If using the Wait-State Generators provided in
register D8, the MWI1-0 bits should be set to 00.
Figure 56. DMA/WAIT Control Register
DS971850301
49
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
SYSTEM CONTROL REGISTERS
IL
Bit
Upon Reset
R/W
IL7
0
R/W
IL6
0
R/W
IL5
0
R/W
0
Addr 33H
0
0
0
0
Interrupt Vector Low
Figure 57. Interrupt Vector Low Register
Bit
Upon Reset
R/W
Addr 34H
ITC
TRAP UFO
0
0
R/W
R
1
-
-
ITE2
ITE1
ITE0
1
1
0
R/W
0
R/W
1
R/W
/INT Enable 2, 1, 0
Undefined Fetch Object
TRAP
Figure 58. INT/TRAP Control Register
Addr 36H
RCR
Bit
Upon Reset
R/W
REFE REFW
1
1
R/W R/W
1
-
-
-
1
1
1
CYC1 CYC0
0
0
R/W R/W
Cycle Select
Refresh Wait State
Refresh Enable
CYC1, 0
Interval of Refresh Cycle
00
01
10
11
10 states
20 states
40 states
80 states
Figure 59. Refresh Control Register
50
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
MMU REGISTERS
CBR
Bit
Upon Reset
R/W
Addr 38H
CB7
CB6
CB5
CB4
CB3
CB2
CB1
CB0
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MMU Common Base
Register
Figure 60. MMU Common Base Register
BBR
Bit
Upon Reset
R/W
Addr 39H
BB7
BB6
BB5
BB4
BB3
BB2
BB1
BB0
0
0
0
0
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MMU Bank Base Register
Figure 61. MMU Bank Base Register
CBAR
Bit
Upon Reset
R/W
Addr 3AH
CA3
CA2
CA1
CA0
BA3
BA2
BA1
BA0
1
1
1
1
0
0
0
0
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
MMU Bank Area Register
MMU Common Area Register
Figure 62. MMU Common/Bank Area Register
DS971850301
51
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
SYSTEM CONTROL REGISTERS
OMCR
Bit
Upon Reset
R/W
M1E /M1TE /IOC
-
-
-
Addr 3EH
-
1
R/W
1
1
1
1
1
W
1
R/W
1
I/O Compatibility
/M1 Temporary Enable
/M1 Enable
Notes:
1. This register should be programmed to 0x0xxxxxb
(x = don't care) as a part of Initialization.
2. If the M1E bit is set to 1, the processor does not
fetch a RETI instruction.
Figure 63. Operation Mode Control Register
ICR
Bit
Upon Reset
IOA7
IOA6 IOSTP
0
0
0
R/W
R/W
R/W
R/W
-
-
-
Addr 3FH
-
1
1
1
1
1
I/O Stop
I/O Address
Combination of 11
is reserved
Figure 64. I/O Control Register
52
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
CPU CONTROL REGISTER
The CPU Control Register allows the programmer to select
options that directly affect the CPU performance as well as
controlling the STANDBY operating mode of the chip. The
CPU Control Register (CCR) allows the programmer to
change the divide-by-two internal clock to divide-by-one.
In addition, applications where EMI noise is a problem, the
Z8S180 can reduce the output drivers on selected groups
of pins to 33 percent of normal pad driver capability which
minimizes the EMI noise generated by the part (Figure 65).
CPU Control Register (CCR) Addr 1FH
D7 D6 D5 D4 D3 D2 D1 D0
0
Clock Divide
0 = XTAL/2
1 = XTAL/1
Standby/Idle Enable
00 = No Standby
01 = Idle After Sleep
10 = Standby After Sleep
11 = Standby After Sleep
64 Cycle Exit
(Quick Recovery)
BREXT
0 = Ignore BUSREQ
In Standby/Idle
1 = Standby/Idle Exit
on BUSREQ
0
0
0
0
0
0
0
New Z8S180 Register
LNAD/DATA
0 = Standard Drive
1 = 33% Drive On
A19-A0, D7-D0
LNCPUCTL
0 = Standard Drive
1 = 33% Drive On CPU
Control Signals
LNIO
0 = Standard Drive
1 = 33% Drive on Certain
External I/O
LNPHI
0 = Standard Drive
1 = 33% Drive On
EXT.PHI Clock
Figure 65. CPU Control Register
DS971850301
53
Zilog
P R E L I M I N A R Y
Bit 7. Clock Divide Select. Bit 7 of the CCR allows the
programmer to set the internal clock to divide the external
clock by two if the bit is 0 and divide-by-one if the bit is 1.
Upon reset, this bit is set to 0 and the part is in
divide-by-two mode. Since the on-board oscillator is not
guaranteed to operate above 20 MHz, an external source
must be used to achieve the maximum 33 MHz operation
of the device, such as an external clock at 66 MHz with 50
percent duty cycle.
If an external oscillator is used in divide-by-one mode, the
minimum pulse width requirement must be satisfied.
Bits 6 and 3. STANDBY/IDLE Enable. These two bits are
used for enabling/disabling the IDLE and STANDBY mode.
Setting D6, D3 to 0 and 1, respectively, enables the IDLE
mode. In the IDLE mode, the clock oscillator is kept
oscillating but the clock to the rest of the internal circuit,
including the CLKOUT, is stopped. The Z8S180 enters
IDLE mode after fetching the second opcode of a SLEEP
instruction, if the I/O STOP bit is set.
Setting D6, D3 to 1 and 0, respectively, enables the
STANDBY mode. In the STANDBY mode, the clock oscillator is stopped completely. The Z8S180 enters STANDBY
after fetching the second opcode of a SLEEP instruction,
if the I/O STOP bit is set.
Setting D6, D3 to 1 and 1, respectively, enables the
STANDBY-QUICK RECOVERY mode. In this mode, its
operations are identical to STANDBY except that the clock
recovery is reduced to 64 clock cycles after the exit
conditions are gathered. Similarly, in STANDBY mode, the
Z8S180 enters STANDBY after fetching the second opcode
of a SLEEP instruction, if the I/O STOP bit is set.
54
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Bit 5. BREXT. This bit controls the ability of the Z8S180 to
honor a bus request during STANDBY mode. If this bit is
set to 1 and the part is in STANDBY mode, a BUSREQ is
honored after the clock stabilization timer is timed out.
Bit 4. LNPHI. This bit controls the drive capability on the
PHI Clock output. If this bit is set to 1, the PHI Clock output
is reduced to 33 percent of its drive capability.
Bit 2. LNIO. This bit controls the drive capability of certain
external I/O pins on the Z8S180. When this bit is set to 1,
the output drive capability of the following pins is reduced
to 33 percent of the original drive capability:
/RTS0/TXS
CKA1
CKA0
TXA0
TXA1
TOUT
Bit 1. LNCPUCTL. This bit controls the drive capability of
the CPU Control pins. When this bit is set to 1, the output
drive capability of the following pins is reduced to 33
percent of the original drive capability:
/BUSACK
/RD
/WR
/M1
/MREQ
/IORQ
/RFSH
/HALT
ST
Bit 0. LNAD/DATA. This bit controls the drive capability of
the Address/Data bus output drivers. If this bit is set to 1,
the output drive capability of the Address and Data bus
output is reduced to 33 percent of its original drive capability.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
ON-CHIP ENHANCED SERIAL COMMUNICATIONS CONTROLLER (EMSCC)
The Z80185 contains a single-channel EMSCC which
features a 4-byte transmit FIFO and an 8-byte receive
FIFO, this enhancement reduces the overhead required to
provide data to, and get data from, the transmitter and
receiver. The EMSCC also improves packet handling in
SDLC mode to:
■
■
■
■
■
■
Write registers: WR3, WR4, WR5, and WR10 are now
readable
■
Read Register 0 Latched During Access
■
Many Improvements to Support SDLC/HDLC Transfers:
– Deactivation of /RTS Pin after Closing Flag
– Automatic Transmission of the Opening Flag
– Automatic Reset of Tx Underrun/EOM Latch
– Complete CRC Reception
– TxD pin Automatically Forced High with NRZI
Encoding when Using Mark Idle.
– Receive FIFO Automatically Unlocked for
Special Receive Interrupts when Using the
SDLC Status FIFO.
– Back-to-Back Frame Transmission Simplified
■
Software Interrupt Acknowledge mode
■
DPLL Counter Output Available as Jitter-Free Clock
Source
■
A Full-Duplex Channel with a Baud Rate Generator
and Digital Phase-Locked Loop
■
Multi-Protocol Operation Under Program Control
■
Asynchronous or Synchronous mode
automatically transmit a flag before the data;
reset the Tx Underrun/EOM latch;
force the TxD pin High at the appropriate time when
using NRZI encoding;
deassert the /RTS pin after the closing flag;
and
better handle ABORTed frames when using the 10x19
status FIFO.
The combination of these features, along with the data
FIFOs, significantly simplifies SDLC driver software.
The CPU hardware interface has been simplified by relieving the databus setup time requirement and supporting
the software generation of the interrupt acknowledge signal (/INTACK). These changes allow an interface with less
external logic to many microprocessor families while maintaining compatibility with existing designs. I/O handling of
the EMSCC is improved over the SCC, with faster response
of the /DTR//REQ pin. The many enhancements added to
the EMSCC permits a system design that increases overall
system performance with better data handling and less
interface logic.
In addition, the following features have been added to the
EMSCC channel in the Z80185:
Significant features of the EMSCC include:
■
Programmable LocalTalk feature
Hardware and software compatible with Zilog's SCC/
ESCC
■
Non-Multiplexed /DTR Pin
■
4-Byte Transmit FIFO
■
Internal Connection of DMA Request and /WAIT Signals
■
8-Byte Receive FIFO
■
■
Programmable FIFO Interrupt Levels Provide Flexible
Interrupt Response
EMSCC Programmable Clock
– Programmed to be Equal to System Clock
Divided by One or Two
– Programmed by System Configuration Register
■
Improved SDLC Frame Status FIFO
■
New Programmable Features Added with Write
Register 7'
■
DS971850301
Note: The EMSCC programmable clock must be programmed to divide-by-two mode when operating above
the following condition: PHI > 20 MHz at 5.0V
55
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Transmit Logic
Transmit FIFO
4 Bytes
Transmit MUX
TxD
Data Encoding & CRC
Generation
/TRxC
Receive and Transmit Clock Multipexer
/RTxC
Digital
Phase-Locked
Loop
Crystal
Oscillator
Amplifier
Baud Rate
Generator
Modem/Control Logic
/CTS
/DCD
/RTS
/DTR
Receive Logic
Rec. Status Rec. Data
FIFO 8-Byte FIFO 8-Byte
SDLC Frame Status FIFO
10 x 19
Internal
Control
Logic
Databus
Control
Interrupt
Control
Receive MUX
CRC Checker,
Data Decode &
Sync Character
Detection
Channel A
Register
Channel A
CPU & DMA
Bus Interface
/INT
/INTACK
IEI
IEO
RxD
Tx-Rx
Interrupt
Control
Logic
Figure 66. EMSCC Block Diagram
56
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
EMSCC
The Z80185 features a one-channel EMSCC that uses two
I/O addresses:
EMSCC Channel A Control
Data
I/O Address %E8
I/O Address %E9
Divide-by-two should be programmed when operating the
Z80185 beyond 20 MHz, 5V.
Note: Upon power-up, or reset, the system clock is equal
to the EMSCC clock.
RR10, and RR15). Two registers (RR12 and RR13) are
read to learn the baud rate generator time constant. RR2
contains either the unmodified interrupt vector (channel A)
or the vector modified by status information (channel B).
RR3 contains the Interrupt Pending (IP) bits (channel A
only). RR6 and RR7 contain the information in the SDLC
Frame Status FIFO, but is only read when WR15 D2 is set.
If WR7' D6 is set, Write Registers WR3, WR4, WR5, WR7,
and WR10 can be read as RR9, RR4, RR5, and RR14,
respectively. Figure 51 shows the format of each read
register.
Initialization. The system program first issues a series of
commands to initialize the basic mode of operation. This is
followed by other commands to qualify conditions within
the selected mode. For example, in the Asynchronous
mode, character length, clock rate, number of stop bits,
and even or odd parity should be set first. Then the
interrupt mode is set, and finally, the receiver and transmitter are enabled.
With the Z80185, the EMSCC channel's DTR, Tx and Rx
DMA Request and WAIT outputs are not subject to multiplexing and are routed separately to the CPU and pins.
Write Registers. The EMSCC contains 16 write registers
(17 counting the transmit buffer) in each channel. These
write registers are programmed separately to configure
the functional "personality" of the channels. A new register,
WR7', was added to the EMSCC and may be written to if
WR15, D0 is set. Figure 50 shows the format of each write
register.
2. if WR1 bits 7-6 are 10, and the processor reads the RDR
when the RxFIFO is empty, or writes the TDR when the
TxFIFO is full, the processor is "waited" until a character
arrives or has been sent out;
In other words,
1. the DTR pin is not multiplexed and always follows WR5
bit 7;
3. WR1 bit 5 has no effect;
4. WR14 bit 2 should be kept 0;
Read Registers. The EMSCC contains ten read registers
(11 counting the receive buffer) in each channel. Four of
these may be read to obtain status information (RR0, RR1,
DS971850301
5. WR1 bits 7-6 should not be programmed as 11.
57
A LocalTalk feature has been added in one EMSCC of the
Z80185, operating as follows:
If a certain set of register bits are set, RTS acts as a
LocalTalk Driver Enable output that operates as shown in
Figure 50. All of the following bits and fields must be
programmed exactly as shown to enable this mode:
WR4.3-2
WR4.5-4
WR5.1
WR7'.2
WR10.3
WR5.4
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
= 00: sync modes
= 10: SDLC
= 0: no RTS
= 1: auto RTS deactivation
= 1: mark idle
= 1: Send Break
When the first five conditions above are set (as for LocalTalk
operation), the WR5.4 bit is used as a Select LocalTalk
Driver Enable control bit, rather than the Send Break
command bit used in async mode.
Setting these register bits in this manner configures the
EMSCC Transmitter to send three Flags before a frame,
negating RTS during the first to create a coding violation,
when software writes the first character of a frame to the
TDR and TxFIFO. This mode also makes the Transmitter
ensure at least 16 bits of idle time between a closing Flag
and the end of frame interrupt. The RTS output is driven
active for one bit time at the start of the first of the three
Flags, then inactive for four bit times, then active again for
the duration of the opening Flags, the frame, and closing
Flag, plus 16 bit times thereafter.
There is one other difference in EMSCC operation when
this new mode is enabled. The setting of the TxIP bit, that
normally occurs after the last bit of the CRC is sent, is
delayed until the 16-bit Idle is sent and RTS is negated.
RTS
TxD
Flag
Flag
Flag
Frame
Flag
16-Bit Idle
Figure 67. EMSCC Transmitter Flag Commands
58
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
EMSCC REGISTERS
Write Register 2
Write Register 0 (non-multiplexed bus mode)
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
V0
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
1
1
0
1
0
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
Register 0
Register 1
Register 2
Register 3
Register 4
Register 5
Register 6
Register 7
Register 8
Register 9
Register 10
Register 11
Register 12
Register 13
Register 14
Register 15
V1
V2
V3
V4
Interrupt
Vector
V5
V6
V7
*
Null Code
Point High
Reset Ext/Status Interrupts
Send Abort (SDLC)
Enable Int on Next Rx Character
Reset Tx Int Pending
Error Reset
Reset Highest IUS
Write Register 3
D7 D6 D5 D4 D3 D2 D1 D0
Rx Enable
Sync Character Load Inhibit
Address Search Mode (SDLC)
Rx CRC Enable
Enter Hunt Mode
Null Code
Reset Rx CRC Checker
Reset Tx CRC Generator
Reset Tx Underrun/EOM Latch
Auto Enables
0
0
1
1
* With Point High Command
0
1
0
1
Rx 5 Bits/Character
Rx 7 Bits/Character
Rx 6 Bits/Character
Rx 8 Bits/Character
Write Register 1
Write Register 4
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
Ext Int Enable
0
0
1
1
0
1
0
1
Tx Int Enable
Parity Enable
Parity is Special Condition
Parity EVEN//ODD
0
0
1
1
Rx Int Disable
Rx Int On First Character or Special Condition
Int On All Rx Characters or Special Condition
Rx Int On Special Condition Only
Reserved,
Program as 00.
0
0
1
1
WAIT Request Enable
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
Sync Modes Enable
1 Stop Bit/Character
1 1/2 Stop Bits/Character
2 Stop Bits/Character
8-Bit Sync Character
16-Bit Sync Character
SDLC Mode (01111110 Flag)
External Sync Mode
X1 Clock Mode
X16 Clock Mode
X32 Clock Mode
X64 Clock Mode
Figure 68. Write Register Bit Functions
DS971850301
59
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Write Register 5
D7 D6 D5 D4 D3 D2 D1 D0
Tx CRC Enable
0
0
1
1
0
1
0
1
RTS
/SDLC/CRC-16
Tx Enable
Send Break (Async Mode)
LocalTalk Driven Enable (HDLC Mode)
Tx 5 Bits(Or Less)/Character
Tx 7 Bits/Character
Tx 6 Bits/Character
Tx 8 Bits/Character
DTR
Write Register 6
D7 D6 D5 D4 D3 D2 D1 D0
Sync7
Sync1
Sync7
Sync3
ADR7
ADR7
Sync6
Sync0
Sync6
Sync2
ADR6
ADR6
Sync5
Sync5
Sync5
Sync1
ADR5
ADR5
Sync4
Sync4
Sync4
Sync0
ADR4
ADR4
Sync3
Sync3
Sync3
1
ADR3
x
Sync2
Sync2
Sync2
1
ADR2
x
Sync1
Sync1
Sync1
1
ADR1
x
Sync0
Sync0
Sync0
1
ADR0
x
Monosync, 8 Bits
Monosync, 6 Bits
Bisync, 16 Bits
Bisync, 12 Bits
SDLC
SDLC (Address Range)
Write Register 7
D7 D6 D5 D4 D3 D2 D1 D0
Sync7
Sync5
Sync15
Sync11
0
Sync6
Sync4
Sync14
Sync10
1
Sync5
Sync3
Sync13
Sync9
1
Sync4
Sync2
Sync12
Sync8
1
Sync3
Sync1
Sync11
Sync7
1
Sync2 Sync1 Sync0
Sync0
x
x
Sync10 Sync9 Sync8
Sync6 Sync5 Sync4
1
1
0
Monosync, 8 Bits
Monosync, 6 Bits
Bisync, 16 Bits
Bisync, 12 Bits
SDLC
Figure 69. Write Register Bit Functions (Continued)
60
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
EMSCC REGISTERS (Continued)
WR' Prime
Write Register 10
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
Auto Tx Flag
Auto EOM Reset
Auto RTS Deactivation
Rx FIFO Int Level
Tx DMA Request Timing Mode
Tx FIFO Int Level
Extended Read Enable
32-Bit CRC Enable
6-Bit//8-Bit Sync
Loop Mode
Abort//Flag On Underrun
Mark//Flag Idle
Go Active On Poll
0
0
1
1
0
1
0
1
NRZ
NRZI
FM1 (Transition = 1)
FM0 (Transition = 0)
CRC Preset I//O
Write Register 11
Write Register 9
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
VIS
NV
DLC
MIE
Status High//Status Low
Software INTACK Enable
0
0
1
1
0
1
0
1
No Reset
Not used
Channel Reset
Force Hardware Reset
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
/TRxC Out = Xtal Output
/TRxC Out = Transmit Clock
/TRxC Out = BR Generator Output
/TRxC Out = DPLL Output
/TRxC O/I
Transmit Clock = /RTxC Pin
Transmit Clock = /TRxC Pin
Transmit Clock = BR Generator Output
Transmit Clock = DPLL Output
Receive Clock = /RTxC Pin
Receive Clock = /TRxC Pin
Receive Clock = BR Generator Output
Receive Clock = DPLL Output
Reserved
Figure 70. Write Register Bit Functions (Continued)
DS971850301
61
P R E L I M I N A R Y
Zilog
Write Register 12
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Write Register 14
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
TC0
TC1
TC2
TC3
TC4
TC5
TC6
TC7
BR Generator Enable
BR Generator Source
Reserved, Program as 0.
Auto Echo
Local Loopback
Lower Byte of
Time Constant
0
0
0
0
1
1
1
1
Write Register 13
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Null Command
Enter Search Mode
Reset Missing Clock
Disable DPLL
Set Source = BR Generator
Set Source = /RTxC
Set FM Mode
Set NRZI Mode
Write Register 15
D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0
TC8
TC9
TC10
TC11
TC12
TC13
TC14
TC15
WR7' SDLC Feature Enable
Upper Byte of
Time Constant
Zero Count IE
SDLC FIFO Enable
DCD IE
Sync/Hunt IE
CTS IE
Tx Underrun/EOM IE
Break/Abort IE
Figure 71. Write Register Bit Functions (Continued)
62
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
EMSCC REGISTERS (Continued)
Read Register 0
D7
D6
Read Register 3
D5
D4
D3
D2
D1
D0
D7
D6
D5
D4
D3
D2
D1
D0
Rx Character Available
0
Zero Count
0
Tx Buffer Empty
0
DCD
Ext/Status IP
Sync/Hunt
Tx IP
CTS
Rx IP
Tx Underrun/EOM
0
Break/Abort
0
Read Register 6*
Read Register 1
D7
D6
D5
D4
D3
D2
D1
D7
D0
D6
D5
D4
D3
D2
D1
D0
BC0
All Sent
BC1
Residue Code 2
BC2
Residue Code 1
BC3
Residue Code 0
BC4
Parity Error
BC5
Rx Overrun Error
BC6
CRC/Framing Error
BC7
End of Frame (SDLC)
*Can only be accessed if the SDLC FIFO enhancement
is enabled (WR15 bit D2 set to 1)
SDLC FIFO Status and Byte Count (LSB)
Read Register 2
D7
D6
D5
D4
D3
D2
D1
D0
Read Register 7*
V0
D7
D6
D5
D4
D3
D2
D1
D0
V1
V2
V3
V4
BC8
Interrupt
Vector
BC9
BC10
V5
BC11
V6
BC12
V7
BC13
FDA: FIFO Data Available
1 = Status Reads from FIFO
0 = Status Reads from EMSCC
FOS: FIFO Overflow Status
1 = FIFO Overflowed
0 = Normal
*Can only be accessed if the SDLC FIFO enhancement
is enabled (WR15 bit D2 set to 1)
SDLC FIFO Status and Byte Count (LSB)
Figure 72. Read Register Bit Functions
DS971850301
63
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Read Register 10
D7
D6
D5
Read Register 13
D4
D3
D2
D1
D0
D7
D6
D5
D5
D4
D3
D2
D1
D0
0
TC8
On Loop
TC9
0
TC10
0
TC11
Loop Sending
TC12
0
TC13
Two Clocks Missing
TC14
One Clock Missing
TC15
Upper Byte
of Time Constant
Read Register 15
Read Register 12
D7
D6
D4
D3
D2
D1
D7
D0
D6
D5
D4
D3
D2
D1
D0
0
TC0
TC1
Zero Count IE
TC2
SDLC Status FIFO Enable
TC3
TC4
Lower Byte
of Time Constant
DCD IE
Sync/Hunt IE
TC5
CTS IE
TC6
Tx Underrun/EOM IE
TC7
Break/Abort IE
Figure 73. Read Register Bit Functions (Continued)
64
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P1284 REGISTER MAP
Register Name
PARM Register
PARC Register
PARC2 Register
PART Register
PARV Register
I/O Addr/Access
(asymmetric)
%D9 R/W
%DA R/W
%DB WO
%DC R/W
%DD R/W
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER
The Centronics P1284 Controller can operate in either the
Host or Peripheral role in Compatibility mode (host to
printer), Nibble or Byte mode (printer to host), and ECP
mode (bidirectional). It provides no hardware support for
the EPP mode, although it may be possible to implement
this mode by software.
Nine control signals have dedicated hardware pins, and
have ± 12 mA drive (P1284 Level 2) capability as does the
8-bit data port PIA27-20. Note: Signal names listed below
are those for the original Compatible mode. The names
shown in parentheses represent the same signal, but in a
more recent mode. The Z80185 does not include hardware
support for the P1284 EPP mode.
The following signals are outputs in a Peripheral mode,
inputs in a Host mode:
■
■
■
■
■
Busy (PtrBusy, PeriphAck)
nAck (PtrClk, PeriphClk)
PError (AckDataReq, nAckReverse)
nFault (nDataAvail, nPeriphRequest)
Select (Xflag)
DS971850301
The following signals are inputs in a Peripheral mode,
outputs in a Host mode:
■
■
■
■
nStrobe (HostClk)
nAutoFd (HostBusy, HostAck)
nSelectIn (P1284Active)
nInit (nReverseRequest)
Note that, because the Host/Peripheral mode is fully controlled by software, a Z80185-based product can operate
as a Host in one system, or as a Peripheral in another,
without any change to the hardware. A Z80185-based
product could even act as a Host at one time and a
Peripheral at another time within the same system, if there
is a mechanism to control such alternate use.
In general, the interface architecture automates operations that are seen as performance-critical, while leaving
less frequent operations to software control. To achieve
top performance, software should assign a DMA channel
to the current direction of data flow.
Note: The IEEE 1284 Interface should be used with the
/IOC bit (bit D5) in the OMCR set to 0. The setting of this bit
primarily affects RLE expansion in peripheral ECP forward
and host ECP reverse modes.
65
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Bidirectional Centronics Registers
Reading the Parallel Controls (PARC) register allows software to sense the state of the input signals per the current
mode, plus two or three status flags:
Busy
PError
Select
nFault
nAck
IllOp
DREQ
Idle
7
6
5
4
3
2
1
0
Figure 74a. Reading PARC in a Host Mode
(I/O Address %DA)
nAutoFd
nStrobe
nSlctIn
nInit
7
6
5
4
3
IllOp
DREQ
Idle
2
1
0
Figure 74b. Reading PARC in a Peripheral Mode
(I/O Address %DA)
The controller sets IllOp (Illegal Operation) when it detects
an error in the protocol, for example, if it’s in Peripheral
mode and it detects that the host has driven P1284Active
(nSelectIn) Low at a time that mandates an immediate
Abort, that is, outside one of the “windows” in which this
event indicates an organized disengagement. If “status
interrupts” are enabled, such an interrupt is always requested when IllOp is set. Writing PARM with NewMode=1
clears IllOp.
DREQ is the Request presented to the DMA channels,
which may or may not be programmed to service this
request. If not, an interrupt can be enabled when DREQ is
set.
Writing to PARC allows the software to set and clear the
output signals per the current mode:
1=drive
nAutoFd
High
1=drive
nStrobe
High
1=drive
nSelctIn
High
1=drive
nInit
High
1=drive
nAutoFd
Low
1=drive
nStrobe
Low
1=drive
nSelctIn
Low
1=drive
nInit
Low
7
6
5
4
3
2
1
0
Figure 75a. Writing to PARC in a Host Mode
(I/O Address %DA)
1=drive
Busy
High
1=drive
PError
High
1=drive
Select
High
1=drive
nFault
High
1=drive
Busy
Low
1=drive
PError
Low
1=drive
Select
Low
1=drive
nFault
Low
7
6
5
4
3
2
1
0
Figure 75b. Writing to PARC in a Peripheral Mode
(I/O Address %DA)
66
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER (Continued)
Because there are five outputs in a Peripheral mode,
another register, called PARC2, allows software to change
the nAck line, rather than the Select line:
1=drive
Busy
High
1=drive
PError
High
1=drive
nAck
High
1=drive
nFault
High
1=drive
Busy
Low
1=drive
PError
Low
1=drive
nAck
Low
1=drive
nFault
Low
7
6
5
4
3
2
1
0
Figure 76. Writing to PARC2 in a Peripheral Mode
(I/O Address %DB)
The Parallel mode register (PARM) includes the basic
mode control of the controller:
NewMode
IdleIE
StatIE
DREQIE
7
6
5
4
Mode
3
2
1
0
Figure 77. PARM (I/O Address %D9)
NewMode = 1 reinitializes the state machine to the initial
state for the mode called out by MODE. Never change
MODE without writing a 1 in this bit.
IdleIE = 1 enables interrupts when the controller sets the
Idle flag. When software uses a DMA channel to provide
data to the P1284 controller, it can be expected that the
channel will do so in a timely manner, and thus, that an Idle
condition signifies that the channel has finished transferring the block. (Software can also enable an interrupt from
the DMA channel, but on the transmit side, such interrupts
are not well-synchronized to events on the P1284 controller.) Conversely, if software provides data, Idle may not be
grounds for an interrupt.
Some modes set the Idle flag when they are entered.
However, such a setting of Idle never requests an interrupt.
StatIE = 1 enables “status” interrupts that are described
separately for each mode.
DREQIE = 1 enables interrupts when the controller sets
DREQ, except that in those modes that set DREQ when
they are entered, such setting doesn’t request an interrupt.
DS971850301
Table 3. Bidirectional Centronics Mode Selection
MODE
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Non-P1284 mode
Peripheral Compatible/Negotiation mode
Peripheral Nibble mode
Peripheral Byte mode
Peripheral ECP Reverse mode
Peripheral Inactive mode
Peripheral ECP Forward mode with software RLE
handling
Peripheral ECP Forward mode with hardware RLE
expansion
Host Negotiation mode
Host Compatible mode
Host Nibble mode
Host Byte mode
Host ECP Forward mode
Host Reserved mode
Host ECP Reverse mode with software RLE
handling
Host ECP Reverse mode with hardware RLE
expansion
67
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
A second output register has been added for PIA27-20.
Writing to either the Z80181-compatible PIA 2 Data Register (address E3) or the new Alternate PIA 2 Data Register
(address EE) writes to the Output Holding Register (OHR).
When the PIA27-20 pins are outputs, the outputs of the
OHR are the inputs to the second register, which is called
the I/O register (IOR), these outputs drive the PIA27-20
pins. When the pins are inputs, they are the inputs to the
IOR, which can be read from the PIA 2 Data Register
(address E3).
In non-P1284 mode, Host Negotiation mode, Reserved
Modes, and in Peripheral Compatible/Negotiation mode
when the host drives nSelectIn (P1284Active) High to
Set IUS
clr IP
clr IUS
7
6
5
select negotiation, the direction of the PIA27-20 pins are
controlled by the PIA 2 Data Direction register, as on the
Z80181. Also in these modes the IOR is loaded on every
PHI clock, so that operation is virtually identical to the
Z80181. In other modes the controller controls the direction of PIA27-20 and when the IOR is loaded.
A Time Constant Register PART must be loaded by software with the smallest number of PHI clocks that equals
or exceeds the “critical time” for the mode selected in
PARM. The critical time is 750 ns for Host Compatible
mode, 500 ns for most other modes, and the time necessary to indicate DMA completion in Host ECP Forward and
Peripheral ECP Reverse modes.
number of PHI clocks in critical time
4
3
2
1
0
Figure 78. PART Write (I/O Address %DC)
Reading PART yields the status of the IP and IUS bits,
which are described in the Bidirectional Centronics Interface section:
IUS
IP
0
7
6
5
number of PHI clocks in critical time
4
3
2
1
0
Figure 79. PART Read (I/O Address %DC)
The Vector Register PARV must be loaded by software with
the interrupt vector to be used for interrupts from this
controller.
Interrupt Vector
7
6
5
4
3
2
1
0
Figure 80. PARV (I/O Address %DD)
68
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER (Continued)
Internal Data Bus
PART
Register
PARM
Register
PARV
Register
Time
Counter
State
Machine
IEI
Interrupt
Logic
IEO
RLE
Counter
State
Counter
Output Holding
Register
Data Path
Clocking
PIA2 Direction
Register
PARC, PARC2
Registers
PIA2 Data
Register
Data Path
Direction
Host/Peripheral
Control Signal
Management
PIA27-20
nAck
Busy
PError
Select
nFault
nAutoFd
nStrobe
nSelectIn
nInit
Figure 81. Bidirectional Centronics P1284 Controller
Functional Block Description
DS971850301
69
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Interrupts
As in other Zilog peripherals, the controller includes an
interrupt pending bit (IP), and an interrupt under service bit
(IUS). The controller is part of an on-chip interrupt acknowledge daisy-chain that extends from the IEI pin, through the
EMSCC, CTC, and this controller in a programmable
priority order, and from the lowest-priority of these devices
to the IEO pin. The interrupt request from the controller is
logically ORed with /INT0 and other on-chip interrupt
requests to the processor.
The controller sets its IP bit whenever any of three conditions occurs:
1. PARM4 is 1, and the controller sets the DREQ bit. This
does not include when the controller forces the DREQ
bit to 1, when software first places the controller in
Peripheral Nibble, Peripheral Byte, Peripheral ECP
Reverse, Host Compatible, or Host ECP Forward mode.
2. PARM5 is 1, and a mode-dependent “status interrupt”
condition occurs. The following sections describe the
status interrupt conditions (if any) for each mode.
3. PARM6 is 1, and the controller sets the Idle bit, except
when the controller forces the Idle bit to 1, when
software first places the controller in Peripheral Nibble,
Peripheral Byte, Peripheral ECP Reverse, Host Compatible, or Host ECP Forward mode. The following
sections describe when Idle is set in each mode.
Once IP is set, it remains set until software writes a 1 to
PART6.
The controller will begin requesting an interrupt of the
processor whenever IP is set, its IEI signal from the on-chip
daisy-chain is High/true, and its IUS bit is 0. Once it starts
requesting an interrupt, the controller will continue to do so
until /IORQ goes Low in an interrupt-acknowledge cycle,
or IP is 0, or IUS is 1.
The controller drives its IEO output High, if its IEI input is
High, and its IP and IUS bits are both 0. A Z80 interrupt
acknowledge cycle is signalled by /M1 going Low, followed by /IORQ going Low. The controller, and all other
devices in the daisy-chain, freeze the contribution of their
IP bits to their IEO outputs while /M1 is Low, which prevents
new events from affecting the daisy-chain. By the time
/IORQ goes Low, one and only one device will have its IEI
pin High and its IEO pin Low — this device responds to the
interrupt by providing an interrupt vector, and setting its
IUS bit. This controller also clears its IP bit when it responds
to an interrupt acknowledge cycle.
70
The interrupt service routine, that is initiated when the
interrupt vector value identifies an interrupt from this controller, should save the processor context and then proceed as follows:
1. If the ISR does not allow nested interrupts, it can clear
the IP and IUS bits by writing hex 60, plus the “critical
time” value to the PART, then read the status from PARC
and proceed based on that status. Near the end of the
ISR it should re-enable processor interrupts.
2. If the ISR allows nested interrupts, it can re-enable
processor interrupts, clear IP by writing hex 40 plus the
“critical time” value to the PART, and then read the
status from PARC and proceed based on that status. At
the end of the ISR it should clear IUS to allow further
interrupts from this controller and devices lower on the
daisy-chain, by writing hex 20 plus the “critical time”
value to the PART.
The remainder of this section describes the operation of
the various PARM register modes that can be selected.
Non-P1284 Mode
The Z80185 defaults to this mode after a Reset, and this
mode is compatible with the use of PIA27-20 on the
Z80181. The directions of PIA27-20 can be controlled
individually by writing to register E2, as on the Z80181. The
state of outputs among PIA27-20 can be set by writing to
register E3, and the state of all eight pins can be sensed by
reading register E3. The Busy, nAck, PError, nFault, and
Select pins are tri-stated in this mode, while nStrobe,
nAutoFd, nSelectIn, and nInit are inputs. There are no
status interrupts in this mode.
Peripheral Inactive Mode
This mode operates identically to Non-P1284 mode as
described above, except that the Busy, nAck, PError,
nFault, and Select pins are outputs that can be controlled
via the PARC and PARC2 registers, and status interrupts
can occur in response to any edge on nAutoFd, nStrobe,
nSelectIn, or nInit. This mode differs from Peripheral Compatibility/Negotiation mode with nSelectIn (P1284 Active)
High, only in that the controller will not operate in Compatibility mode if nSelectIn goes Low.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER (Continued)
Host Compatible Mode
Host Negotiation Mode
1. Setting this mode configures PIA27-20 as outputs regardless of the contents of register E2. When entering
this mode, the controller sets the Idle and DREQ bits,
but these settings do not request an interrupt.
Setting this mode puts PIA27-20 under control of registers
E2 and E3, as on the Z80181.
2. If software, or a DMA channel, writes eight bits to the
Output Holding Register (OHR) when Idle is set, the
controller transfers the byte to the Input/Output Register and negates DREQ only momentarily, so as to
request another byte from software or the DMA channel.
3. In this mode, the nAutoFd line is not under control of the
PARC register, but rather under control of which register the software uses to write data to the OHR. Each time
the controller transfers a byte from the OHR to the Input/
Output Register, it sets nAutoFd High if the byte was
written to address E3, and Low if the byte was written to
the “alternate” address EE. In a DMA application all of
the bytes transferred from one output buffer will have
the same state of nAutoFd, but this state can be
changed from one buffer to the next by changing the
I/O address used by the DMA channel. In non-DMA
applications software can set the state of nAutoFd for
each character, by writing data to the two different
register addresses.
4. When a data byte has been valid on PIA27-20 for 750
ns (as controlled by the PART register), and the Busy
and PError lines are Low and the Select, nAck, and
nFault lines are High, the controller drives nStrobe Low.
After the controller has held nStrobe Low for 750 ns it
drives nStrobe back to High. Then it waits for 750 ns of
data hold time to elapse. If software or a DMA channel
has written another byte to the Output Holding Register
(thus clearing DREQ) by the time this wait is satisfied,
the controller transfers the byte from the Output Holding
Register to the Input/Output Register, sets DREQ again,
and returns to the event sequence at the start of this
paragraph. Otherwise, it sets Idle and returns to the
event sequence at the start of paragraph #2.
Status interrupts in this mode include rising and falling
edges on PError, nFault, and Select.
DS971850301
Software has complete control of the controller, and can
either revert to Host Compatibility mode, or set one of the
following Host modes, depending on how the peripheral
responds to the Negotiation value(s).
Status interrupts in this mode include rising and falling
edges on PtrClk (nAck), nAckReverse (PError), and
nPeriphRequest (nFault). nFault is not used during actual
P1284 negotiation, but is included because these events
are significant during Byte and ECP mode idle times.
Host Reserved Mode
This mode differs from Host Negotiation mode only in that
there are no status interrupts in this mode.
Peripheral Compatible/Negotiation Mode
In this mode, if P1284Active (nSelectIn) is Low, the controller sets PIA27-20 as inputs, regardless of the contents of
register E2; when P1284Active (nSelectIn) is High, PIA2720 are under the control of registers E2 and E3. On entry
to this mode, the controller sets the Idle bit, if DREQ is set
from a previous mode.
If, in this mode, nStrobe goes (is) Low, P1284Active
(nSelectIn) is Low, and DREQ is 0, indicating that any
previous data has been taken by the processor or DMA
channel, the controller captures the data on PIA27-20 into
the Input/Output Register, sets DREQ to notify software or
the DMA channel to take the byte, drives the Busy line
High, and one PHI clock later drives nAck Low. When at
least 500 ns (as controlled by the PART register) have
elapsed, the controller drives nAck back to High. One PHI
clock later, if the CPU or DMA has taken the data and thus
cleared DREQ, the controller drives Busy back to Low,
otherwise it sets Idle.
Select, PError and nFault are under software control in this
mode, and nAutoFd can be sensed by software, but has no
other effect on operation.
71
P R E L I M I N A R Y
Zilog
In this mode, software should monitor for the condition
P1284Active (nSelectIn) High, and nAutoFd Low simultaneously. If software detects this state, it should participate
in a Negotiation process. Software should read the value
on PIA27-20 and set PError, nFault, XFlag, and nAck as
appropriate for the data value. As long as P1284Active
(nSelectIn) remains High in this mode, software is in
complete control of the controller. After the host has driven
nStrobe Low and then High again for an acceptable value,
software should reprogram the MODE field to the appropriate one of the following Peripheral modes.
Status interrupts in this mode include rising and falling
edges on P1284Active (nSelectIn) and nInit, and rising
and falling edges on HostBusy (nAutoFd) and HostClk
(nStrobe) while P1284Active (nSelectIn) is High.
Host Nibble Mode
1. If, during Host Negotiation mode, software has placed
the value 00 or 04 on the data lines, and received a
positive response on Xflag (Select) and a Low on
nDataAvail (nFault) at a rising edge of PtrClk (nAck),
then after optionally programming a DMA channel to
store data, it should set this mode.
2. For each byte in this mode, the controller drives HostBusy
(nAutoFd) Low and waits until DREQ is cleared, indicating that the CPU or DMA has taken any previous data,
and the peripheral has driven PtrClk (nAck) Low. At this
point it samples the other four status lines from the
peripheral into the less-significant four bits of the Input/
Output Register as follows:
Table 4. Nibble Mode Bit Assignments
72
Signal
First Data Bit
Second Data Bit
Busy
PError
Select
nFault
3
2
1
0
7
6
5
4
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
The controller then drives HostBusy (nAutoFd) back to
High, and waits for the peripheral to drive PtrClk (nAck)
back to High. Then it drives HostBusy (nAutoFd) back
to Low and waits for the peripheral to drive PtrClk (nAck)
Low. At this point it samples the four status lines from the
peripheral into the most-significant four bits of the Input/
Output Register, as shown above. Then it drives
HostBusy (nAutoFd) back to High, sets the DREQ bit,
and waits for the peripheral to drive PtrClk (nAck) back
to High. When this occurs, if the peripheral is driving
nDataAvail (nFault) Low, indicating more data is available, the controller then returns to the event sequence
at the start of paragraph #2.
3. If nDataAvail (nFault) is High at a rising edge of nAck in
this mode, indicating that the peripheral has no more
data, the controller sets Idle and waits for software to
program it back to Host Negotiation mode. Software
can then select the next mode (reference IEEE P1284
specification).
If host software is programmed not to select all the data
that a peripheral has available, it should first disable the
DMA channel, if one is in use, then wait for DREQ to be 1
and PtrClk (nAck) to be High. If nDataAvail (nFault) is Low
at this point, the controller will have already driven HostBusy
(nAutoFd) Low to solicit the next byte. Software should
then program the controller back to Host Negotiation
mode, read the IOR to get the current byte, and take the
next byte from the peripheral under software control. After
the peripheral drives nAck High after the second nibble,
software can drive P1284Active (nSelectIn) Low to tell the
peripheral to leave Nibble mode.
There are no status interrupts in Host Nibble mode.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER (Continued)
Peripheral Nibble Mode
1. Software shouldn’t set this mode until there is reverse
data available to send. In other words, it should implement the P1284 “reverse idle mode” via software in
Peripheral Compatibility/Negotiation mode. After software has driven nDataAvail (nFault), AckDataReq
(PError), and Xflag (Select) all Low to signify that data
is available, then driven PtrClk (nAck) High after 500 ns,
and if requested programmed a DMA channel to provide data to send, when it sees HostBusy (nAutoFd)
Low to request data, software should set this mode.
Setting this mode sets DREQ and Idle, but these settings
do not request an interrupt. The PIA27-20 pins remain
configured for data input but are not used. Instead, four of
the five control outputs are driven with the LS and MS four
bits of the Input/Output Register, as shown in Table 2, while
PtrClk (nAck) serves as a handshake/clock output. On
entering this mode the hardware begins routing bits 3-0 of
the IOR to these lines.
2. If software, or a DMA channel, writes a byte to the
Output Holding Register when Idle is set, the controller
immediately transfers the byte to the IOR and clears
Idle, and negates DREQ only momentarily to request
another byte from software or the DMA channel.
3. After data has been valid on the four control outputs for
500 ns (as controlled by the PART register), the controller drives the PtrClk (nAck) line Low. Then it waits for the
host to drive the HostBusy (nAutoFd) line back to High,
after which it drives PtrClk (nAck) back to High, switches
the four control lines to bits 7-4 of the IOR, and begins
waiting for the host to drive HostBusy (nAutoFd) back to
Low. When bits 7-4 have been valid for 500 ns and the
host has driven HostBusy (nAutoFd) Low, the controller
drives PtrClk (nAck) Low again and begins waiting for
the host to drive HostBusy (nAutoFd) High. When
HostBusy (nAutoFd) has been driven High, the controller returns the four control outputs to the state set by
software in PARC. At this point, if software or a DMA
channel has not yet written another byte to the Output
Holding Register (thus clearing DREQ), the controller
sets Idle and waits for software to do so. If/when
software or a DMA channel has written a new byte to the
OHR, the controller transfers the byte to the IOR, sets
DREQ, and clears Idle if it had been set. Then, when the
control outputs have been valid for 500 ns, the controller drives PtrClk (nAck) to High. It then waits for the host
to drive HostBusy (nAutoFd) back to Low, at which time
it switches the four control lines back to bits 3-0 of the
IOR and returns to the event sequence at the start of this
paragraph.
DS971850301
If there is no more data to send, when the controller sets
Idle, software should modify PARC to make nDataAvail
(nFault) and AckDataReq (PError) High, and then change
the mode to Peripheral Compatible/Negotiation. Then (after 500 ns) software should set PtrClk (nAck) back to High
in PARC and enter Reverse Idle state.
Status interrupts in Peripheral Nibble mode include rising
and falling edges on P1284Active (nSelectIn) and nInit.
The controller sets the IllOp (Illegal Operation) bit if
P1284Active (nSelectIn) goes Low in this mode, before it
drives nAck High for the status states on the four control
lines, or after the host drives HostBusy Low thereafter, in
which case software should immediately enter Peripheral
Compatibility/Negotiation mode. If P1284Active goes Low,
but IllOp stays 0, indicating that the Host negated
P1284Active in a legitimate manner, software should enter
Peripheral Inactive mode for the duration of the “return to
Compatibility mode”, and then enter Peripheral Compatibility/Negotiation mode.
Host Byte Mode
1. When in Host Negotiation mode the software has presented the value hex 01 or 05 on PIA27-20, it has been
acknowledged by the peripheral, and the peripheral
has driven nDataAvail (nFault) and AckDataReq (PError)
to Low to indicate data availability and then driven
PtrClk (nAck) back to High, software should set this
mode. This sets PIA27-20 as inputs regardless of the
contents of register E2, and clears the Idle flag. The
controller then waits 500 ns (as controlled by the PART
register) before proceeding.
2. For each byte, the controller drives HostBusy (nAutoFd)
Low to indicate readiness for a byte from the peripheral.
Then it waits for PtrClk (nAck) to go Low, at which time
it captures the state of PIA27-20 into the Input/Output
Register; sets the DREQ bit to request software, or the
DMA channel to take the byte, and drives HostBusy
(nAutoFd) High and HostClk (nStrobe) Low. When
software, or the DMA channel, has taken the byte (thus
clearing DREQ) and the peripheral has driven PtrClk
(nAck) back High, and at least 500 ns after driving
HostClk (nStrobe) Low, the controller drives HostClk
(nStrobe) back to High, and samples nDataAvail (nFault).
If it is still Low, the controller returns to the event
sequence at the start of this paragraph, otherwise it sets
the Idle flag.
73
Zilog
P R E L I M I N A R Y
In response to Idle, software should enter Host Negotiation
mode. Thereafter, it can set HostBusy (nAutoFd) Low, to
enter Reverse Idle state, or enter Host Compatible mode
(reference IEEE P1284 specification), or conduct a new
negotiation.
If software is programmed not to accept all the data that a
peripheral has available in this mode, it should first disable
the DMA channel, if one is in use, and then wait for DREQ
to be 1 and nAck to be 1. Then it should reprogram the
controller back to Host Negotiation mode, read the last
byte from the IOR, drive HostClk (nStrobe) back to High,
and then drive P1284Active (nSelectIn) Low to instruct the
peripheral to leave Byte mode.
There are no status interrupts in Host Byte mode.
Peripheral Byte Mode
1. Software should not set this mode until there is reverse
data available to send — that is, it should implement the
P1284 “reverse idle mode” via software in Peripheral
Compatibility/Negotiation mode. The exact sequencing among PtrClk (nAck), nDataAvail (nFault), and
AckDataReq (PError) differs according to whether this
mode is entered directly from Negotiation or from
reverse idle phase, and is controlled by software. But in
either case, before software sets this mode, it should
set nDataAvail (nFault) and AckDataReq (PError) to
Low, then after 500 ns, set PtrClk (nAck) to High. When
it detects that the host has driven HostBusy (nAutoFd)
Low to request data, software should set this mode,
which sets the DREQ and Idle flags.
2. In this mode, as long as P1284Active (nSelectIn) remains High, the controller drives PIA27-20 as outputs,
regardless of the contents of register E2. When software, or a DMA channel, writes the first byte to the
Output Holding Register, the controller immediately
transfers the byte to the Input/Output Register, clears
Idle but negates DREQ only momentarily, to request
another byte from software, or the DMA channel.
3. After each byte is transferred to the IOR, the controller
waits 500 ns data setup time (as controlled by the PART
register) before driving PtrClk (nAck) Low, and thereafter waits for the host to drive HostBusy (nAutoFd) High.
74
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
When this occurs, if software, or the DMA channel, has
not written more data to the Output Holding Register,
that is, if DREQ is still set, the controller sets the Idle flag
and waits for software or the DMA channel to do so. If
software, or the DMA channel, then writes data to the
Output Holding Register, the controller clears DREQ
and Idle. When there is data in the OHR and DREQ is 0,
this guarantees that it is appropriate to keep nDataAvail
(nFault), and AckDataReq (PError) Low to indicate that
more data is available, and the controller drives PtrClk
(nAck) back to High. The controller then waits for a
rising edge on HostClk (nStrobe), and then for the host
to drive HostBusy (nAutoFd) Low, at which time it
transfers the byte from the OHR to the Output Register,
sets DREQ, and then it returns to the event sequence at
the start of this paragraph.
While this mode is in effect, software should monitor the
interface for two conditions:
Case 1: Idle set and no more data to send, or
Case 2: P1284Active (nSelectIn) Low.
In Case #1, the software should write zero to register E3 to
keep PIA27-20 outputs momentarily, and then set the
mode back to Peripheral Compatibility, so that the interface is fully under software control, set nDataAvail (nFault)
and AckDataReq (PError) High to signify no more data,
wait 500 ns, and set PtrClk (nAck) back to High. When
HostBusy goes back to Low, the software should set
PIA27-20 back to inputs.
In Case #2, if a falling edge on P1284Active happens any
time other than between a rising edge on HostClk (nStrobe),
and the next falling edge on HostBusy (nAutoFd), the
controller sets the IllOp bit to notify software that an
immediate Abort is in order, in which case software should
immediately enter Peripheral Compatibility/Negotiation
Mode. If P1284Active goes Low, but IllOp is not set,
meaning that the Host negated P1284Active in a “legal”
manner, software should enter Peripheral Inactive Mode
for the duration of the “return to Compatibility Mode”, and
then enter Peripheral Compatibility/Negotiation Mode.
Status interrupts in Peripheral Byte Mode include rising
and falling edges on P1284Active (nSelectIn) and nInit.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER (Continued)
Host ECP Forward Mode
1. After a negotiation for ECP mode, “host” software
should remain in Negotiation mode so that it has complete control of the interface, until one of two situations
occurs. If software has data to send, it should optionally
program the DMA channel to provide the data, and then
set this mode. Alternatively, if software has no data to
send and it detects that nPeriphRequest (nFault) has
gone Low, indicating the peripheral is requesting reverse transfer, it should set PIA27-20 as inputs, wait 500
ns, drive nReverseRequest (nInit) to Low to indicate a
reverse transfer, and then set Host ECP Reverse mode.
In other words, software should handle all aspects of
ECP mode, other than active data transfer sequences.
2. Setting this mode configures PIA27-20 as outputs regardless of the contents of register E2. On entry to this
mode, the controller sets Idle and DREQ to request a
byte from software or a DMA channel, but these settings
do not cause an interrupt request.
3. If software, or a DMA channel, writes data to the Output
Holding Register while the Input/Output Register is
empty, the controller immediately transfers the byte to
the IOR, clears Idle, and negates DREQ only momentarily, to request another byte.
4. In this mode, the alternate address for the Output
Holding Register allows software to send a “channel
address” or an RLE count value. Such bytes are typically written by software rather than a DMA channel.
Writing to the alternate address loads the OHR and
clears DREQ, like writing to the primary address, but
clears a ninth bit that is set when software, or a DMA
channel, writes to the primary address. A similar ninth
bit is associated with the Input/Output Register, from
which it drives the HostAck (nAutoFd) line.
DS971850301
5. As each nine bits arrive in the IOR and thus out onto
PIA27-20 and HostAck (nAutoFd), the controller waits
one PHI clock and then drives HostClk (nStrobe) to
Low. It then waits for the peripheral to drive PeriphAck
(Busy) to High, after which it drives HostClk (nStrobe)
back to High. Then it waits for the peripheral to drive
PeriphAck (Busy) back to Low. When this has happened, if software or a DMA channel has written a new
byte to the Output Holding Register, and thus cleared
DREQ, the controller transfers the byte to the IOR, sets
DREQ again, and returns to the event sequence at the
start of this paragraph. Otherwise, it returns to the event
sequence at the start of paragraph #3. If software, or a
DMA channel, does not provide a new byte for the time
indicated in the PART register, the controller sets the
Idle flag.
6. While this mode is in effect, software should monitor for
the condition "Idle and no more data left to send", and/
or nPeriphRequest (nFault) Low. Host software has
complete freedom as to whether to honor the peripheral’s
reverse request on nFault while it has data to send.
When there is no more data, software can set Host
Negotiation mode to have full control of the interface,
and if requested can drive P1284Active (nSelectIn) to
Low in order to terminate ECP mode, or can set Host
ECP Reverse mode, wait 500 ns, and drive
nReverseRequest (nInit) to Low.
Status interrupts in Host ECP Forward mode include rising
and falling edges on nPeriphRequest (nFault).
75
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Peripheral ECP Forward Modes
1. After a negotiation for ECP mode, “peripheral” software
should remain in Compatibility/Negotiation mode with
P1284Active (nSelectIn) High, so that it has complete
control of the interface, though when it detects the host
drive HostAck (nAutoFd) Low for the second time, it
should then set nAckReverse (PError) High. If software
has data to send, it should drive nPeriphRequest (nFault)
Low at the same time, and optionally program a DMA
channel to provide the data. Whether or not it has data
to send, software should then set one of the two ECP
Forward modes.
2. In these modes, the controller configures PIA27-20 as
inputs regardless of the contents of register E2. On
entry to one of these modes, the controller clears the
Idle bit, if it had been set.
3. For each byte, the controller waits for the host to drive
HostClk (nStrobe) to Low. When HostClk (nStrobe) is
Low and software, or the DMA channel, has taken any
previous byte and thus cleared DREQ, operation diverges into four cases depending on the state of
HostAck (nAutoFd), the mode, the MSbit of the data,
and the state of an internal 7-bit Run-Length Encoding
(RLE) counter.
If HostAck (nAutoFd) is High, indicating that this byte is
neither an RLE value, nor a Channel Address, the controller captures the data from PIA27-20 into the Input/Output
Register, sets DREQ to request software, or the DMA
channel, to take this byte, and drives PeriphAck (Busy)
High. If the RLE counter is zero, the controller waits (if
necessary) for the host to drive HostClk (nStrobe) back to
High, after which it drives PeriphAck (Busy) back to Low
and returns to the event sequence at the start of paragraph
#3. If the RLE counter is non-zero, the controller waits for
software, or a DMA channel, to read the byte from the
Input/Output Register, negates DREQ only momentarily,
and decrements the RLE counter. It does this until the RLE
counter is zero, at which point it proceeds as described
above. Thus an RLE value of “n” results in the next byte
being provided to software, or a DMA channel “n+1” times.
4. If HostAck (nAutoFd) is Low and the MS bit of the byte
is zero (PIA27 is Low), the byte is an RLE repeat count.
If the mode is “hardware RLE expansion," the controller
transfers (the seven LS bits of) it to the RLE counter,
leaves DREQ cleared, and drives PeriphAck (Busy)
High.
76
5. Thereafter, the controller waits for the host to drive
HostClk (nStrobe) back to High, at which time it drives
PeriphAck (Busy) back to Low, and returns to the event
sequence at the start of paragraph #3.
6. If HostAck (nAutoFd) is Low, and PIA27 is High, the byte
is a “channel address." In this case, or when PIA27 is
Low and the mode is “software RLE handling," the
controller captures the data from PIA27-20 into the
Input/Output Register, leaves DREQ cleared to keep a
DMA channel from storing the byte, and sets the Idle bit,
which it does not otherwise set while in this mode.
Software should respond to this condition by reading
the byte from the PIA 2 data register E3. Software can
then do whatever else is needed to handle the situation,
and then set Busy High. Thereafter the controller clears
Idle, waits (if necessary) for the host to drive HostClk
(nStrobe) back to High, and then drives PeriphAck
(Busy) back to Low and returns to the event sequence
at the start of paragraph #3.
While this mode is set, if data to send becomes available,
software should drive nPeriphRequest (nFault) Low to alert
the host of this fact. Also software should monitor the
controller for either of two conditions:
a. If the host drives nReverseRequest (nInit) Low in response to nPeriphRequest (nFault) Low, software should
drive nAckReverse (PError) Low, optionally program a
DMA channel to provide the data, and set Peripheral
ECP Reverse mode.
b. If P1284Active (nSelectIn) goes Low, the controller sets
the IllOp bit in PARC, if this occurs between the time the
host drives HostClk (nStrobe) Low, and when the controller subsequently drives PeriphAck (Busy) back to
Low, in which case software should immediately enter
Peripheral Compatibility/Negotiation mode. If P1284Active goes Low, but IllOp stays zero, indicating a “legal”
termination, software should enter Peripheral Inactive
mode and sequence the nAckReverse (PError),
PeriphAck (Busy), PeriphClk (nAck), nPeriphRequest
(nFault), and Xflag (Select) lines to leave ECP mode.
Status interrupts in Peripheral ECP Forward mode include
rising and falling edges on P1284Active (nSelectIn) and
nReverseRequest (nInit).
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 BIDIRECTIONAL CENTRONICS P1284 CONTROLLER (Continued)
Host ECP Reverse Modes
1. In these modes the controller configures PIA27-20 as
inputs, regardless of the contents of register E2. On
entry to one of these modes, the controller clears the
Idle bit, if it had been set.
2. For each byte, the controller waits for the peripheral to
drive PeriphClk (nAck) Low. When this happens, and
software, or the DMA channel, has taken any previous
byte from the Input/Output Register and thus cleared
DREQ, operation diverges into four cases, depending
on the state of PeriphAck (Busy), the mode, the LS bit
of the data, and the state of an internal 7-bit RLE
counter.
If PeriphAck (Busy) is High, indicating that this byte is
neither an RLE value nor a Channel Address, the
controller captures the data from PIA27-20 in the IOR,
sets DREQ to notify software, or the DMA channel to
take the byte, and drives HostAck (nAutoFd) High. If the
RLE counter is zero, the controller then waits (if necessary) for the peripheral to drive PeriphClk (nAck) back
to High, after which it drives HostAck (nAutoFd) back to
Low and returns to the event sequence at the start of
paragraph #2. If the RLE counter is non-zero, the
controller waits for software, or the DMA channel, to
read the byte from the IOR, negates DREQ only momentarily, and decrements the RLE counter. It does this
until the RLE counter is zero, at which point it proceeds
as described above. Thus an RLE value of “n” results in
the next byte being provided to software or a DMA
channel “n+1” times.
3. If PeriphAck (Busy) is Low, and the MSbit of the byte is
zero (PIA27 is Low), the byte is an RLE repeat count. If
the mode is “hardware RLE expansion,” the controller
transfers (the seven LSbits of) it to the RLE counter,
DS971850301
leaves DREQ cleared, and drives HostAck (nAutoFd)
High. Thereafter the controller waits for the peripheral to
drive PeriphClk (nAck) back to High, at which time it
drives HostAck (nAutoFd) back to Low and returns to
the event sequence at the start of paragraph #2.
4. If PeriphAck (Busy) is Low, and the MSbit of the byte is
1 (PIA27 is High), the byte is a “channel address”. In this
case, or when the LSbit is zero, but the mode is
“software RLE handling," the controller captures the
data from PIA27-20 in the IOR, leaves DREQ cleared, to
keep a DMA channel from storing the byte, and sets
Idle, which it does not otherwise set in this mode.
Software should respond to this condition by reading
the byte from the PIA 2 data register E3, reprogramming
a DMA channel, if necessary, and doing whatever else
is needed to handle the channel address, and finally
setting HostAck (nAutoFd) High. Thereafter the controller clears Idle, waits for the peripheral to drive PeriphClk
(nAck) back to High, and then drives HostAck (nAutoFd)
back to Low, and returns to the start of the event
sequence in paragraph #2 above.
5. If data has become available to be sent while this mode
is in effect and software elects to send it, it should drive
nReverseRequest (nInit) to High, set Host Negotiation
mode to take full control of the interface, wait for
nAckReverse (PError) to go High, and then set PIA2720 as outputs.
6. Status interrupts in Host ECP Reverse mode include
rising and falling edges on nPeriphRequest (nFault).
nPeriphRequest carries a valid “reverse data available”
indication during Reverse ECP mode. If so, enable
status interrupts during this mode; if not, disable them.
77
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Peripheral ECP Reverse Mode
1. In this mode, as long as nReverseRequest (nInit) is Low,
and P1284Active (nSelectIn) is High, the controller
drives the contents of the Input/Output Register onto
PIA27-20, regardless of the contents of the E2 register.
On entry to this mode, the controller sets Idle, and sets
DREQ to request data from software, or a DMA channel.
2. If software, or a DMA channel, writes data to the Output
Holding Register while the Input/Output Register is
empty, the controller immediately transfers the byte to
the IOR, clears Idle, and negates DREQ only momentarily, to request another byte.
3. In this mode, an alternate address for the Output
Holding Register allows software to send a “channel
address” or an RLE count value. Such bytes are not
typically written by a DMA channel. Writing to this
alternate address loads the OHR and clears DREQ, the
same as writing to the primary address, but clears a
ninth bit set when software, or a DMA channel, writes to
the primary address. A similar ninth bit is associated
with the IOR, and drives the PeriphAck (Busy) line in this
mode.
4. As each nine bits arrive in the IOR, and thus out onto
PIA27-20 and PeriphAck (Busy), the controller waits
one PHI clock, and then drives PeriphClk (nAck) Low.
78
It then waits for the host to drive HostAck (nAutoFd)
High, after which it drives PeriphClk (nAck) back to
High. The controller then waits for the host to drive
HostAck (nAutoFd) back to Low. When this has happened, if software, or the DMA channel, has written a
new byte to the Output Holding Register, and thus
cleared DREQ, the controller transfers the byte to the
IOR, sets DREQ again, and returns to the start of the
event sequence in this paragraph. Otherwise, it returns
to the event sequence at the start of paragraph #2. If
software, or the DMA channel, doesn’t provide new
data within the time indicated by the PART register, the
controller sets the Idle bit.
5. While this mode is in effect, software should monitor
whether the host drives nReverseRequest (nInit) High.
If it detects this, it should set the mode back to Peripheral ECP Forward, wait 500 ns and then drive
nAckReverse (PError) back to High, before proceeding
as described for Peripheral ECP Forward mode above.
6. Status interrupts in Peripheral ECP Reverse mode include rising and falling edges on P1284Active
(nSelectIn) and nReverseRequest (nInit). Since there
are no “legal terminations” during the time this mode is
set, the controller sets IllOp for any falling edge on
P1284Active (nSelectIn) in this mode.
DS971850301
Zilog
P R E L I M I N A R Y
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 CTC, AND MISCELLANEOUS REGISTERS
The following section describes miscellaneous registers
that control the Z80185 configuration, including RAM/
ROM registers, Interrupt and various Status and Timer
registers.
Register Name
WSG Chip Select Register
PIA1/CTC Pin Select Register
Interrupt Edge Control
PIA 1 Data Direction Register
PIA 1 Data Register
PIA 2 Data Direction Register
PIA 2 Data Register
CTC Channel 0 Control Register
CTC Channel 1 Control Register
CTC Channel 2 Control Register
CTC Channel 3 Control Register
DS971850301
I/O Addr/Access
%D8 R/W
%DE R/W
%DF R/W
%E0 R/W
%E1 R/W
%E2 R/W
%E3 R/W
%E4 R/W
%E5 R/W
%E6 R/W
%E7 R/W
Register Name
EMSCC Control Register
EMSCC Data Register
RAMUBR RAM Upper Boundary Reg
RAMLBR RAM Lower Boundary Reg
ROM Address Boundary Reg.
System Configuration Reg.
PIA 2 Data Alternate Address
WDT Master Register
WDT Command Register
I/O Addr/Access
%E8 R/W
%E9 R/W
%EA R/W
%EB R/W
%EC R/W
%ED R/W
%EE R/W
%F0 R/W
%F1 WO
79
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
System Configuration Register
This register controls a number of device-level features on
the Z80185 and includes the following control bits:
D7
D6
D5
D4
D3
D2
D1
D0
Daisy-Chain Configuration
ROM Emulator Mode (REME)
0 = Data Bus in Normal Mode
1 = Data Bus in ROM Emulator Mode
0 = ESCC CLK is PHI
1 = ESCC CLK is PHI/2
0 = /RTS0, /CTS0, CKA0
1 = TxS, RxS, CKS
Disable /ROMCS
0 = /ROMCS is Enabled
1 = /ROMCS is Disabled
Daisy-Chain Configuration
Decode High I/O
0 = A15-8 not decoded for
"non-180" registers.
1 = A15-8 must be 00 to
access "non-180" regs.
Figure 82. System Configuration Register
(I/O Address %ED)
80
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 PIA AND MISCELLANEOUS REGISTERS (Continued)
System Configuration Register (Continued)
Bit 7. Decode High I/O. If this bit is 0, as it is after a Reset,
A15-8 are not decoded for the registers for which A7-6 are
11, that is, the registers for the EMSCC, CTCs, I/O Ports,
Bidirectional Centronics Controller. If this bit is 1, A15-8
must all be zero to access these registers, as for the other
registers in the Z80185. When set to 0, this bit is compatible
with the Z80181 and Z80182, and allows shorter, and more
basic I/O instructions to be used to access these registers.
Alternately, when set to 1, this bit allows more extensive offchip I/O.
Bit 6. Daisy-Chain Configuration Bit 2. This bit is described
with bits 1-0 below.
Bit 5. Disable /ROMCS. When this bit is 1, /ROMCS is
forced to High, regardless of the status of the address
decode logic. This bit Resets to 0 so that /ROMCS is
enabled.
Bit 4. When this bit is 0, the /RTS0/TXS, /CTS0/RXS, and
CKA0/CKS pins have the /RTS0, /CTS0 and CKA0 func-
tions, respectively. When this bit is 1, the pins have the
TXS, RXS, and CKS functions, and the CSIO facility can be
used. When this bit is 1, if ASCI0 is used, the “CTS autoenable” function must not be enabled. The multiplexing of
CKA0 is important only with respect to output — the same
external clock could be used for both ASCI0 and the CSIO.
Bit 3. When this bit is 0, the PCLK clock of the EMSCC is
the same as the processor’s PHI clock. When this bit is 1,
this clock is PHI/2. Set this bit if the PHI clock is too fast for
the EMSCC.
Bit 2. ROM Emulator Mode Enable. When this bit is 1, read
data from on-chip sources is driven onto the D7-D0 pins,
as shown in Table 6. This bit resets to 0.
Bits 1-0. These bits, plus bit 6, determine the routing of the
on-chip interrupt daisy-chain, and thus the relative interrupt priority of the on-chip interrupt sources on the daisychain as shown in Table 5.
Table 5. Interrupt Daisy-Chain Routing
b6
b1
b0
Daisy Chain Configuration
0
0
0
0
0
1
0
1
X
IEI pin -> EMSCC -> CTC -> Bidirectional Centronics Controller -> IEO pin
IEI pin -> EMSCC -> Bidirectional Centronics Controller -> CTC -> IEO pin
IEI pin -> Bidirectional Centronics Controller -> EMSCC -> CTC -> IEO pin
1
1
1
0
0
1
0
1
X
IEI pin -> CTC -> EMSCC -> Bidirectional Centronics Controller -> IEO pin
IEI pin -> CTC -> Bidirectional Centronics Controller -> EMSCC -> IEO pin
IEI pin -> Bidirectional Centronics Controller -> CTC -> EMSCC -> IEO pin
DS971850301
81
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Zilog
Table 6. Data Bus Direction (Z185 Bus Master)
I/O and Memory Transactions
I/O Read
from Off-Chip
Peripherals
I/O Write
to On-Chip
Peripherals
I/O Read
from On-Chip
Peripherals
I/O Write
to Off-Chip
Peripherals
Z80185
Data Bus
(ROME=0)
Out
Z
Out
In
Out
Z
In
Z
Z
Z80185
Data Bus
(ROME=1)
Out
Out
Out
In
Out
Out
In
Z
Z
Write to
Memory
Read From Read From
On-Chip
Off-Chip
ROM
Memory
Refresh
Z80185
Idle Mode
Interrupt Acknowledge Transaction
Intack for
On-Chip
Peripheral
Intack for
Off-Chip
Peripheral
Z80185
Data Bus
(ROME=0)
Z
In
Z80185
Data Bus
(ROME=1)
Out
In
Table 8. Data Bus Direction (Z185 Is Not Bus Master)
I/O and Memory Transactions
I/O Write
to On-Chip
Peripherals
I/O Read
from On-Chip
Peripherals
I/O Read
from Off-Chip
Peripherals
Z80185
Data Bus
(ROME=0)
In
Out
Z
Z
Z
Out
In
Z
Z
Z80185
Data Bus
(ROME=1)
In
Out
Z
Z
Z
Out
In
Z
Z
I/O Write
to On-Chip
Peripherals
Write to
Memory
Read From Read From
On-Chip
Off-Chip
ROM
Memory
Refresh
Ext.
Bus Master
is Idle
Interrupt Acknowledge Transaction
Intack for
On-Chip
Peripheral
Intack for
Off-Chip
Peripheral
Z80185
Data Bus
(ROME=0)
Out
In
Z80185
Data Bus
(ROME=1)
Out
In
Notes:
"Out" means that the Z185 data bus direction is in output mode; "In" means
input mode, and "Z" means High impedance. ROME stands for ROM
Emulator mode and is the status of the D2 bit in the System Configuration
Register.
82
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
Z80185 PIA AND MISCELLANEOUS REGISTERS (Continued)
RAM And ROM Registers
Three registers, ROMBR, RAMLBR and RAMUBR, and two
pins, /ROMCS and /RAMCS, assist with decoding of ROM
and RAM blocks of memory.
RAMUBR (I/O Address %EA)
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
/ROMCS can be forced to a “1” (inactive state) by setting
bit 5 in the System Configuration Register, to allow the user
to overlay the RAM area over the ROM area.
ROMBR (I/O Address %EC)
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
A19-A12 ROMBR
A19-A12 RAMUBR
Figure 85. ROMBR (I/O Address %EC)
Figure 83. RAMUBR (I/O Address %EA)
/RAMCS and /ROMCS are active for accesses by an
external master, as well as by the Z80185 processor. If
/ROMCS and /RAMCS are programmed to overlap,
/ROMCS is asserted and /RAMCS is inactive for addresses
in the overlapping region.
RAMLBR (I/O Address %EB)
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
A19-A12 RAMLBR
Figure 84. RAMLBR (I/O Address %EB)
Chip Select signals are active for the address range:
/ROMCS: (ROMBR) >= A19-A12 >=
Size of On-Chip ROM (if enabled, else 0)
/RAMCS: (RAMUBR) >= A19-A12 >= (RAMLBR)
The names RAMUBR and RAMLBR stand for RAM Upper
Boundary Range and RAM Lower Boundary Range. These
two registers specify the address range for the /RAMCS
signal. When accessed, memory addresses are less than,
or equal, to the value in the RAMUBR, and greater than, or
equal to, the value programmed in the RAMLBR, /RAMCS
is asserted.
ROMBR ROM Address Boundary Register
All three of the above registers are set to “FFh” at PowerOn Reset. This means that if on-chip ROM is enabled,
/ROMCS is asserted for all addresses above the size of onchip ROM, if not, /ROMCS is asserted for all addresses.
Since /ROMCS takes priority over /RAMCS, the latter will
never be asserted until the value in the ROMBR and
RAMLBR registers are re-initialized to lower values.
This register specifies the address range for the /ROMCS
signal. When an accessed memory address is less than, or
equal to, the value programmed in this register, but greater
than the size of on-chip ROM (if on-chip ROM is enabled),
the /ROMCS signal is asserted.
DS971850301
83
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Wait State Generation (WSG)
The Memory Wait Insertion field of the DCNTL register
applies to all accesses to memory, and allows insertion of
0-3 wait states. In the Z80185, the WSG Chip Select
Register allows individual wait state control for the various
types and areas of memory.
WSG Chip Select Register (I/O Address %D8)
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
Other Memory Wait Insertion
Bits 3-2. This field controls how many wait states are
inserted for accesses to on-chip ROM, and is encoded like
bits 7-6. Note: On-chip ROM should be fast enough to
support no-wait-state operation at the maximum specified
clock rate, but this field is included as a “hedge” against
difficulties in this area, as well as to provide timing compatibility in unusual circumstances.
Bits 1-0. This field controls how many wait states are
inserted for accesses to external memory in which neither
/RAMCS nor /ROMCS is asserted, and is encoded the
same as bits 7-6.
On-Chip ROM Wait Insertion
/ROMCS Wait Insertion
/RAMCS Wait Insertion
Figure 86. WSG Chip Select Register
(I/O Address %D8)
All fields in this register Reset to 11. The 4-wait-state
feature is included to allow the use of commodity DRAMs
with a clock rate at, or near, the maximum.
Note that this facility, and the one in the DCNTL register,
both logically OR into the WAIT signal, to allow this register
full control of wait states. Bits 7-6 of DCNTL should be
programmed to 00.
Bits 7-6. This field controls how many wait states are
inserted for accesses to external memory in which /RAMCS
is asserted: 00 = none, 01 = 1, 10 = 2, 11 = 4 wait states.
Bits 5-4. This field controls how many wait states are
inserted for accesses to external memory in which /ROMCS
is asserted, and is encoded like bits 7-6.
84
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 PIA AND MISCELLANEOUS REGISTERS (Continued)
Interrupt Edge Register
Interrupt Edge Register (I/O Address %DF)
7
6
5
4
3
2
1
0
0
1
0
1
0
0
0
0
0 = /DCD0/CKA0 is /DCD0
1 = /DCD0/CKA0 is CKA0
Drive Select for pins listed below
0 Select normal drive
1 Select low noise (33%)
drive capabilities
/INT1 Sense/Unlatch
0 in: /INT1 is low
1 in: /INT1 is high
out: unlatch edge detection
/INT2 Sense/Unlatch
0 in: /INT2 is low
1 in: /INT2 is high
out: unlatch edge detection
/INT1 Mode Select
0X Normal Level Detect
10 Falling (Neg) Edge Det.
11 Rising (Pos) Edge Det.
/INT2 Mode Select
0X Normal Level Detect
10 Falling (Neg) Edge Det.
11 Rising (Pos) Edge Det.
Figure 87. Interrupt Edge Register
(I/O Address %DF)
Bits 7-6. These bits control the interrupt capture logic for
the /INT2 pin. When these bits are 0X, the /INT2 pin is level
sensitive and Low active. When these bits are 10, negative
edge detection is enabled. Any falling edge will latch an
active Low on the internal /INT2 to the processor. This
interrupt must be cleared by writing a 1 to bit 3 of this
register. Programming these bits to 11 enables rising edge
interrupts to be latched. The latch must be cleared in the
same fashion as for a falling edge.
DS971850301
Bits 5-4. These bits control the interrupt capture logic for
the external /INT1 pin. When these bits are 0X, the /INT1 pin
is level sensitive and Low active. When these bits are 10,
negative edge detection is enabled. Any falling edge will
latch an active Low on the internal /INT1 to the processor.
This interrupt must be cleared by writing a 1 to bit 2 of this
register. Programming these bits to 11 enables rising edge
interrupts to be latched. The latch must be cleared in the
same fashion as for a falling edge.
Bit 3. Software can read this register to sense the state of
the /INT2 pin. Writing a 1 to this bit clears the edge
detection logic for /INT2.
Bit 2. Software can read this register to sense the state of
the /INT1 pin. Writing a 1 to this bit clears the edge
detection logic for /INT1.
Bit 1. This bit selects low noise or normal drive for the
parallel ports, bidirectional Centronics controller pins,
Chip Select pins, and EMSCC pins as follows:
PIA 10-13
PIA 14-16/ZCT0 0-2
PIA 27-20
/ROMCS
/RAMCS
/IOCS
IEO
/RTS
/DTR
TXD
/TRXC
BUSY
nAck
nAutoFd
nFault
nInit
nSelectIn
nStrobe
PError
Select
A 1 in this bit selects the low noise option, which is a 33
percent reduction in drive capability. A 0 selects normal
drive, and is the default after power-up. Additionally, refer
to CPU Register (CCR) for a list of the pins that are
programmable for low drive, via the CCR register.
Bit 0. If this bit is 1, the /DCD0/CKA1 pin has the CKA1
function. The pin is always connected to the DCD input of
ASCI0, so if this pin is 1, and ASCI0 is used, it should not
be programmed to use DCD as a receive auto-enable.
85
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Individual Pin Selection Between PIA1 and
CTCs
The assignment of the choice between PIA1 and CTC I/Os
is controlled by the PIA1/CTC Pin Select Register (Figure
79).
Bit 7. Reserved, and should be programmed as 0.
Bits 6-4. When the PIA1 data direction register has set the
corresponding pins as outputs, for each of these bits that
is 0, the pin is driven with the state of the corresponding bit
of the PIA 1 Data register, while for each of these bits that
is 1, the associated pin is driven with the indicated CTC
output. These bits Reset to 0.
Bits 3-1. These bits control whether the CLK/TRG inputs of
CTCs 3-1 are taken from PIA3-1, respectively, or from the
ZC/TO outputs of CTC2-0, respectively. These bits do not
have any affect on the operating mode of the CTCs.
Bit 0. This bit is reserved and should be programmed as
0. CTC0's CLK/TRG0 input is always connected to the
PIA10 pin.
PIA1/CTC Pin Select Register (I/O Address %DE)
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
Reserved, program as 0.
PIA11/CLKTRG1
1 = CLK/TRG1 = ZC/TO0
0 = CLK/TRG1 = pin
PIA12/CLKTRG2
0 = CLK/TRG2 = ZC/TO1
1 = CLK/TRG2 = pin
PIA13/CLKTRG3
0 = CLK/TRG3 = ZC/TO2
1 = CLK/TRG3 = pin
PIA14/ZCTO1
0 = PIA14
1 = ZC/TO1
PIA15/ZCTO2
0 = PIA15
1 = ZC/TO2
PIA16/ZCTO3
0 = PIA16
1 = ZC/TO3
Reserved, program as 0.
Figure 88. PIA1/CTC Pin Select Register
(I/O Address %DE)
86
DS971850301
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Z80185 PIA AND MISCELLANEOUS REGISTERS (Continued)
CTC Control Registers
Channel Control Byte
This byte is used to set the operating modes and parameters. Bit D0 must be a 1 to indicate that this is a Control
Byte (Figure 82).
Table 8. CTC Operation Modes
CCW6
CCW3
0
0
(Auto Start) Timer mode. The
prescaler is clocked by PHI, and the
counter is clocked by the prescaler.
Counting is enabled when the timer
constant is loaded.
0
1
Timer with CLK/TRG Trigger. The
prescaler is clocked by PHI, and the
counter is clocked by the prescaler.
Timing starts when the transition
specified by D4 is detected on the
PIA pin, or for CTC3-1, the ZC/T0
output of CTC2-0, respectively.
1
0
Classic Counter mode. The counter
is clocked by the PIA pin, or for
CTC3-1 the ZC/TO output of
CTC-2 respectively.
1
1
Long Counter mode. The prescaler
is clocked by the PIA pin, or for
CTC3-1 the ZC/TO output of
CTC-2, respectively, and the
counter is clocked by the prescaler.
The Channel Control Byte register has the following fields:
Bit D7. Interrupt Enable. This bit enables the interrupt logic
so that an internal INT is generated at zero count. Interrupts
are programmed in either mode, and may be enabled or
disabled at any time.
Bit D6. Mode Bit. This bit, along with bit 3, is used to select
either Timer mode or Counter mode (Table 8).
Bit D5. Prescaler Factor. This bit selects the prescaler
factor for use in the timer mode. Either divide-by-16 or
divide-by-256 is available.
Bit D4. Clock/Trigger Edge Selector. This bit selects the
active edge of the CLK/TRG input pulses.
Bit D3. Mode Bit. This bit, along with bit 6, selects either
Timer mode or Counter mode (Table 8).
Bit D2. Time Constant. This bit indicates that the next byte
programmed is time constant data for the downcounter.
Operation
Bit D1. Software Reset. Writing a 1 to this bit indicates a
software reset operation, which stops counting activities
until another time constant word is written.
DS971850301
87
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
Addr: E4h (Ch 0)
E5h (Ch 1)
E6h (Ch 2)
E7h (Ch 3)
D7 D6 D5 D4 D3 D2 D1 D0
Control or Vector
0 Vector
1 Control Word
Reset
0 Continued Operation
1 Software Reset
Time Constant
0 No Time Constant Follows
1 Time Constant Follows
Mode
CCW6 CCW3
0
0
0
1
1
0
1
1
Timer Mode (Auto Start)
Timer Mode CLK/TRG Pulse Starts
Classic Counter Mode
Long Counter Mode
CLK/TRG Edge Selection
0 Selects Falling Edge
1 Selects Rising Edge
Prescaler Value
1 Value of 256
0 Value of 16
Interrupt
1 Enables Interrupt
0 Disables Interrupt
Figure 89. CTC Channel Control Word
88
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
Z80185 PIA AND MISCELLANEOUS REGISTERS (Continued)
CTC Control Registers (Continued)
Time Constant
Before a channel can start counting, it must receive a time
constant. The time constant value may be anywhere between 1 and 256, with 0 indicating a count of 256 (Figure
90).
D7 D6 D5 D4 D3 D2 D1 D0
Interrupt Vector
If one or more of the CTC channels have interrupt enabled,
then the Interrupt Vector Word should be programmed.
Only the five most significant bits of this word are used, bit
D0 must be 0 . Bits D2-D1 are automatically modified by
the CTC channels after responding with an interrupt vector
(Figure 91).
TC0
TC1
TC2
TC3
TC4
TC5
TC6
TC7
Figure 90. CTC Time Constant
D7 D6 D5 D4 D3 D2 D1 D0
0 Interrupt Vector Register
1 Control Register
Channel Identifier
(Automatically Inserted by CTC)
0 0 Channel 0
0 1 Channel 1
1 0 Channel 2
1 1 Channel 3
Supplied By User
Figure 91. CTC Interrupt Vector
Watch-Dog Timer
The Z80185's Watch-Dog Timer (WDT) facility is identical
to Zilog's Z84C15 WDT with the following exceptions:
1. The HALT mode field of the WDT Master Register is not
used. Power control is handled as on the Z8S180.
DS971850301
2. Rather than having a separate /WDTOUT output pin,
the output of the WDT is logically Low-active-ORed with
the /RESET pin. A new register bit controls whether this
affects only the processor, by means of an internal logic
gate, or whether it also drives the /RESET pin Low in an
open-drain manner, so that external logic can be Reset
by the WDT as well. The latter is the default state after
power-up or Reset.
89
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
P R E L I M I N A R Y
Watch-Dog Control Registers
Two registers control WDT operations. These are WDT
Master Register (WDTMR; I/O Address F0h) and the WDT
Command Register (WDTCR; I/O Address F1h). WDT
logic has a “double key” structure to prevent accidental
disabling of the WDT.
Bit D3-D0. Reserved. These three bits are reserved and
should always be programmed as 0011. Reading these
bits returns 0011.
7
6
5
4
3
2
1
0
1
1
1
1
0
0
1
1
Enabling the WDT. The WDT is enabled by reset, and
setting the WDT Enable Bit (WDTMR7) to 1.
Should be 0011
Drive /RESET
0 = WDT output only resets 185
1 = Output of WDT is driven
onto /RESET pin
Disabling the WDT. The WDT is disabled by clearing WDT
Enable bit (WDTR7) to 0 followed by writing "B1h” to the
WDT Command Register (WDTCR; I/O Address F1h).
WDT Periodic Field
00 = Period is (TcC X 2*16)
01 = Period is (TcC X 2*18)
10 = Period is (TcC X 2*20)
11 = Period is (TcC X 2*22)
Clearing the WDT. The WDT can be cleared by writing
“4Eh” into the WDTCR.
Watch-Dog Timer Enable
0 = Disable
1 = Enable
Watch-Dog Timer Master Register (WDTMR;I/O address F0h). This register controls the activities of the
Watch-Dog Timer.
Bit D7. Watch-Dog Timer Enable (WDTE). The WDT can be
enabled by setting this bit to 1. To disable WDT, write 0 to
this bit, followed by writing “B1h” to the WDT Command
Register. Upon Power-On Reset, this bit is set to 1 and the
WDT is enabled.
Figure 92. Watch-Dog Timer Master Register
(I/O Address %F0)
Watch-Dog Timer Command Register (WDTCR; I/O
Address F1h). This register is Write Only (Figure 93).
Bit D6-D5. WDT Periodic field (WDTP). This 2-bit field
determines the desired time period. Upon Power-on reset,
this field sets to "11".
Write B1h after clearing WDTE to “0” - Disable WDT
Write 4Eh - Clear WDT
WDTCR (Write Only)
00 - Period is (TcC * 216)
01 - Period is (TcC * 218)
10 - Period is (TcC * 220)
11 - Period is (TcC * 222)
Bit D4. If this bit is 1 and the WDT times out, the Z80185
drives the /Reset pin Low to reset external logic. If this bit
is 0, a WDT timer only resets the Z80185 internally.
90
D7 D6 D5 D4 D3 D2 D1 D0
1
0
1
1
0
0
0
1
(B1h) - Disable WDT
(After Clearing WDTE)
0
1
0
0
1
1
1
0
(4Eh) - Clear WDT to zero
Figure 93. Watch-Dog Timer Command Register
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
Z80185 PIA AND MISCELLANEOUS REGISTERS (Continued)
Parallel Ports
The Z80185 has two 8-bit bidirectional ports. Each bit is
individually programmable for input or output. Each port
includes two registers: the Port Direction Control Register
and the Port Data Register. The second port also includes
an Alternate Address that is used with the Bidirectional
Centronics feature.
The data direction register determines which of the PIA2720 pins are inputs and outputs. When a bit is set to a 1, the
corresponding pin is an input. If the bit is 0, then the
corresponding bit is an output. These settings can be
overridden by the Bidirectional Centronics Controller.
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
PIA 1 Data Direction Register
0 = Output
1 = Input
Figure 94. PIA 1 Data Direction Register
(I/O Address %E0)
The data direction register determines which of the PIA1610 pins are inputs and outputs. When a bit is set to 1, the
corresponding bit in the PIA 1 Data Register is an input. If
the bit is 0, then the corresponding pin is an output. These
bits must be set appropriately if these pins are used for
CTC inputs and outputs.
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
PIA 1 Data Register
PIA 2 Data Register
Figure 97. PIA 2 Data Register (I/O Address %E3)
When the processor writes to the PIA 2 Data Register, the
data is stored in the internal buffer. Any bits that are output
are then driven on to the pins. In certain modes of the
Bidirectional Centronics Controller, an intermediate register called the Output Holding Register is activated, and the
transfer of data from the OHR to the pins is under the
control of the controller.
When the processor reads the PIA 2 Data Register, the
data on the external pins is returned. In certain modes of
the Bidirectional Centronics Controller, reading from this
address reads the data stored in the port register from
PIA27-20 under the control of the controller.
Figure 95. PIA 1 Data Register (I/O Address %E1)
7
6
5
4
3
2
1
0
When the processor writes to the PIA 1 Data Register, the
data is stored in the internal buffer. Any bits that are output
are then driven on to the pins.
0
0
0
0
0
0
0
0
When the processor reads the PIA 1 Data Register, the
data on the external pins is returned.
Figure 98. PIA 2 Data Alternate Address
(RW) (I/O Address %EE)
7
6
5
4
3
2
1
0
0
0
0
0
0
0
0
0
PIA 2 Data Register
Figure 96. PIA 2 Data Direction Register
(I/O Address %E2)
DS971850301
PIA 2 Data Register
Reading and writing this register is exactly the same as
reading and writing address E3 as described above,
except that in certain modes of the Bidirectional Centronics
Controller, writing to this address sets a “ninth bit” in the
opposite sense from writing address E3, and this drives
one of the control outputs with the opposite polarity.
91
P R E L I M I N A R Y
Zilog
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
ELECTRICAL CHARACTERISTICS
The following classification table describes pins in terms of
input and output classes. VDD = 5V ± 10%, unless otherwise
noted.
Pin Input/Output Classification
92
Class “O” output:
Full time / totem pole
VOL 0.4V max at IOL = 2.0 mA
VOH = VDD –1.2V min at IOH = 200 µA
Slew rate 0.33 V/ns min at CLOAD = 50 pF
COUT = 15 pF max (output or I/O)
Class “3” output:
as “O” except tri-state.
Class “H” output:
as “O” except VOH = VDD-0.6V min at IOH = 200 µA
Class “D” output:
Open Drain
VOL 0.4V max at IOL = 12 mA
COUT = 15 pF max (output or I/O)
Class “T” output:
Tri-State
As Class "O" at VDD = 3.3V ± 10%
VOL 0.4V max at IOL = 12 mA, VDD = 5V ± 10%
VOH 2.4V min at IOH = 12 mA, VDD = 5V ± 10%
Output impedance 45 ohms max
Slew rate 0.05 - 0.40 V/ns (CLOAD not stated by IEEE)
COUT =15 pF max (output or I/O)
Class “I” input”:
VIL 0.8V max at VDD = 5V ± 10%
VIL 0.6V max at VDD = 3.3V ± 10%
VIH 2.0V min
Ii ± 10 µA max, Vi = 0 to 5V (includes leakage if I/O)
CIN = 5 pF max (if input only, see output type if I/O)
Inputs of this type include Weak Latch circuits.
Class “R” input:
VIL 0.6V max
VIH VDD-0.6 min at VDD = 5V ± 10%
VIH VDD-0.3 min at VDD = 3.3V ± 10%
Ii ± 10 µA max, Vi = 0 to 5V
CIN = 5 pF max
Class “S” input:
VIL 0.8V max at VDD = 5V ± 10%
VIL 0.6V max at VDD = 3.3V ± 10%
VIH 2.0V min
Hysteresis 0.2V min
Ii ± 20 µA max, Vi=0.8 to 2V (includes leakage if I/O)
Inputs of this type include Weak Latch circuits.
DS971850301
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
P R E L I M I N A R Y
Zilog
ELECTRICAL CHARACTERISTICS (Continued)
The following table shows the characteristics of each pin
in terms of the above classifications. A dash "–" in the input
or output column indicates the pin does not have that
function.
Table 9. Pin Classification Characteristics
Pin
Input Class
Output Class
/BUSREQ
/CTS
/CTS0/RxS
/DCD
/DCD0/CKA1
I
I
I
I
I
–
–
–
–
3
/DTR
/HALT
/INT0
/INT1
/INT2
/IOCS
–
–
I
I
I
–
O
O
D
–
–
O
/IORQ
/M1
/MREQ
/NMI
/RAMCS
/RD
I
I
I
R
–
I
3
3
3
–
O
3
/RESET
/RFSH
/ROMCS
/RTS
/RTS0/TxS
R
–
–
–
–
D
O
O
O
O
/RTXC
/TRXC
/WAIT
/WR
A0-A19
I
I
I
I
I
3
3
D
3
3
DS971850301
Pin
Input Class
Output Class
Busy
CKA0/CKS
D0-D7
EXTAL
IEI
IEO
S
I
I
R
I
–
T
3
3
–
–
O
nAck
nAutoFd
nFault
nInit
nSelectIn
nStrobe
S
S
S
S
S
S
T
T
T
T
T
T
PError
PHI
PIA13-10/CLKTRG3-0
PIA15-13/ZCTO2-0
PIA27-20
RXA0
S
–
I
I
S
I
T
H
3
3
T
–
RXA1
RXD
/ST
Select
TOUT//DREQ
I
I
–
S
I
–
–
O
T
O
TXA0
TXA1
TXD
XTAL
–
–
–
–
O
O
O
O
93
Zilog
P R E L I M I N A R Y
Z80185/Z80195
SMART PERIPHERAL CONTROLLERS
PACKAGE INFORMATION
100-Pin QFP Package Diagram
94
DS971850301
P R E L I M I N A R Y
Zilog
Z80185/Z80195
S MART PERIPHERAL CONTROLLES
ORDERING INFORMATION
Z80185 (ROM Version)
20 MHz
Z8018520FSC
33 MHz
Z8018533FSC
Z80195 (ROMless Version)
20 MHz
Z8019520FSC
33 MHz
Z8019533FSC
For fast results, contact your local Zilog sales office for
assistance in ordering the part(s) desired.
Package:
F = Plastic Quad Flatpack
Temperature:
S = 0°C to +70°C
Speeds:
20 = 20 MHz
33 = 33 MHZ
Environmental:
C = Plastic Standard
Example:
Z 80185 20 F S C
is a Z80185, 20 MHz, QFP, 0°C to +70°C, Plastic Standard Flow
Environmental Flow
Temperature
Package
Speed
Product Number
Zilog Prefix
© 1997 by Zilog, Inc. All rights reserved. No part of this document
may be copied or reproduced in any form or by any means
without the prior written consent of Zilog, Inc. The information in
this document is subject to change without notice. Devices sold
by Zilog, Inc. are covered by warranty and patent indemnification
provisions appearing in Zilog, Inc. Terms and Conditions of Sale
only. Zilog, Inc. makes no warranty, express, statutory, implied or
by description, regarding the information set forth herein or
regarding the freedom of the described devices from intellectual
property infringement. Zilog, Inc. makes no warranty of merchantability or fitness for any purpose. Zilog, Inc. shall not be
responsible for any errors that may appear in this document.
Zilog, Inc. makes no commitment to update or keep current the
information contained in this document.
DS971850301
Zilog’s products are not authorized for use as critical components in life support devices or systems unless a specific written
agreement pertaining to such intended use is executed between
the customer and Zilog prior to use. Life support devices or
systems are those which are intended for surgical implantation
into the body, or which sustains life whose failure to perform,
when properly used in accordance with instructions for use
provided in the labeling, can be reasonably expected to result in
significant injury to the user.
Zilog, Inc. 210 East Hacienda Ave.
Campbell, CA 95008-6600
Telephone (408) 370-8000
Telex 910-338-7621
FAX 408 370-8056
Internet: http://www.zilog.com
95