Optic receiver module KSM-90□LM1E DIMENSIONS The KSM-90□LM1E consist of a PIN Photodiode of high speed and a preamplifier IC in the package as an receiver for Infrared remote control systems Features ㆍWide angle design ㆍWide supply-voltage range : 2.7V to 5.5V ㆍShielded against electrical field disturbance ㆍHigh immunity against ambient light disturbances (Logic Controller Adaptation) ㆍAvailable for carrier frequencies between 32.7KHz to 56.9KHz ㆍTTL and CMOS compatible Applications ㆍAudio & Video Applications (TV, VTR, Audio, DVDP, CDP) ㆍHome Appliances (Air conditioner, Computer, Camcoder) ㆍWireless Toys ㆍRemote Control Equipment Maximum Ratings Parameter Supply Voltage Operating Temperature Storage Temperature Symbol Vcc Topr Tstg Ratings 6.0 -10 ~ +60 -20 ~ +75 [Ta=25℃] Unit V ℃ ℃ Soldering Temperature Tsol 260 ℃ B.P.F Center Frequency (Max 5 sec) Model No. KSM-901LM1E KSM-902LM1E KSM-903LM1E B.P.F Center Frequency(㎑) 40.0 36.7 37.9 KSM-904LM1E 32.7 KSM-905LM1E 56.9 Electro-Optical Characteristics Parameter Recommended Supply Voltage Current Consumption Peak Wavelength *1 B.P.F Center Frequency Symbol Vcc Icc λp fo Condition No signal input Transmission Distance *1 L 250±50lx High level Output voltage *1 VOH 30cm over Low level Output voltage *1 0˚ ±30˚ VOL the ray axis High level Output Pulse Width *1 TWH Burst wave=600㎲ Low level Output Pulse Width *1 Output Form TWL Period = 1.2㎳ Min. 2.7 0.5 15 12 4.5(2.8) [Ta=25℃, Vcc=5.0V(Vcc=3.0V)] Typ. Max. Unit 5.5 V 1.2(1.0) 1.7 ㎃ 940 ㎚ 37.9 ㎑ m 5.0(3.0) V - 0.1 0.5 V 500 600 700 ㎲ 500 600 Active Low Output 700 ㎲ *1. It specifies the maxmum distance between emitter and detector that the output wave form satisfies the standard under the conditions below against the standard transmitter. 1) Measuring place : Indoor without extreme reflection of light 2) Ambient light source : Detecting surface illumination shall be irradiate 200±50lx under ordinary white fluorescence lamp without high frequency lightning 3) Standard transmitter : Burst wave of standard transmitter shall be arranged to 50mVP-P under the measuring circuit 1/2 Optic receiver module KSM-90□LM1E ■ Measuring Method [Ta=25℃] Output Pulse Width Standard Transmitter Test Method of Transmission Distance Transmitter output Carrier Frequency(fo) Duty50% +5V 600us 600us 10㏀ Standard Tansmitter Vout Remocon output pulse 10㏀ Transmitter T WL 10㎌ OSC Vcc Arrival Distance : L Vout GND : Indicates horizontal and vertical directions THL VL VH 25Cm ■ Typical Characteristics Curve [Ta=25℃] Relative reception distance Vs. Supply voltage Relative reception distance Relative reception distance 120 [%] Relative reception distance Vs. Ambient temperature 100 80 60 40 20 120 [%] 100 20 ˚ 2.5 3.0 3.5 4.0 4.5 5.0 5.5 [V] 60 40 -80 ˚ 80˚ 20 0 -10 0 20 10 30 40 50 60] [℃ 100 ˚ 50 C Relative Sensitivity [%] Rp micom Vout GND GND *1 Recommended Circuit Description 1) Transmitter(IRED) drive current : IFP = 300mAP-P ~ 600mAP-P 2) R-C Decoupling Filter with Lower Cut-off Frequency : R=100Ω , C=47㎌ ⇒ fc = 1/2π RC = 33.9Hz 3) External pull-up resistor(optional) : 10kΩ over 2/2 -100˚ 100 Vcc Vcc 50 100 R Transmitter -40˚ -60 ˚ ■ Standard Application Circuit with R-C Decoupling Filter Receiver Module -20 ˚ 60˚ Ambient temperature Ta Supply voltage Vcc 0˚ 40 ˚ 80 0 0 Radiant pattern