AKM AKD4390-SA

[AKD4390-SA]
AKD4390-SA
AK4390 Sound quality evaluation board Rev.2
General Description
AKD4390-SA is an evaluation board, which is 32Bit ΔΣDAC. The AKD4390-SA includes a LPF which can
add differential analog outputs from the AK4390 and also has a digital interface. Therefore, it is evaluate
sound quality of the AK4390.
Ordering Guide
AKD4390-SA --- Sound quality evaluation board for AK4390
Function
On-board Analog output buffer circuit
On-board digital audio interface. (AK4115)
2nd Order LPF
Lch
DIR
COAX In
AK4115
AK4390
Opt In
Rch
Figure 1. Block diagram
* Circuit diagram are attached at the end of this manual.
COAX is recommended for an evaluation of the Sound quality.
<KM093004>
1
2009/02
[AKD4390-SA]
„ Operation sequence
1) Set up the power supply lines. (See “Other jumpers set-up”.)
Name
Color
Voltage
+15V
Red
+12∼+15V
-15V
Blue
-12∼-15V
AGND
Black
0V
Comments
Regulator,
Power supply for Op-amp.
Attention
This jack is always needed. Power line
Power supply for Op-amp.
This jack is always needed. Power line
GND
This jack is always needed.
Table 1. Set up of power supply lines
Each supply line should be distributed from the power supply unit.
2) Set-up the jumper pins
3) Set-up the DIP switches. (See the followings.)
4) Power on
The AK4390 should be reset once bringing SW3 (PDN) “L” upon power-up.
<KM093004>
2
2009/02
[AKD4390-SA]
„ Evaluation mode
1.
DIR(COAX) (default)
The DIR generates MCLK, BICK, LRCK and SDATA from the received data through BNC connector (J7). It is possible for
the evaluation using such as CD test disk.
Setting:R87 = open;
R88 = short (0Ω)
COAX is recommended for an evaluation of the Sound quality.
2.
DIR(Optical)
The DIR generates MCLK, BICK, LRCK and SDATA from the received data through Optical connector (PORT2). It is
possible for the evaluation using such as CD test disk.
Setting:R87 = short (0Ω);
3.
R88 = open
All clocks are fed through the PORT1.
Setting:
-R54, R55, R56, R58 = open
-R50, R51, R52 = 100Ω; R53 = 5.1Ω
„ DIP Switch setting
[SW1]: AK4115 setting
No.
Pin
1
2
OCKS1
OCKS0
OFF
ON
Master Clock setting of AK4115
Refer to Table 4
Default
ON
OFF
Table 2. SW1 setting
[SW2]: AK4390 setting
No.
Pin
OFF
ON
Default
1
2
P/S
Serial mode
Parallel mode
OFF
Table 3. SW2 setting
<KM093004>
3
2009/02
[AKD4390-SA]
The frequency of the master clock output is set by OCKS0 and OCKS1 as shown in Table 4.
OCKS1
OFF
ON
ON
OCKS0
OFF
OFF
ON
MCLK Frequency
256fs @fs=88.2/96kHz
512fs @fs=32/44.1/48kHz
128fs @fs=176.4/192kHz
(Default)
Table 4. MCLK Setting
„ SW3 setting
[SW3](PDN): Reset of AK4390. Select “H” during operation.
External Analog Circuit
The differential output circuit and LPF is implemented on board. The differential outputs of AK4390 is buffered by non-inverted circuit(2nd
st
order LPF, fc=106.4k, Q=0.698, G=+3.9dB). LPF adds differential outputs(1 order LPF, fc=284k, G=-0.84dB). LME49710NA is used
for op-amp on this board that has low noise and high voltage torelance characteristics. Analog signal is output via BNC connectors on the
board. The output level is about 2.8Vrms (typ@VREF=5.0V) by BNC.
+15
6.8n
+
220
AOUTL- +
6.8n
10k
220
LME49710NA
7
3
2 +
4
-15
10u
0.1u
6
+
10u
620
620
6.8n
+
220
3
+
2 -
6.8n
2
- 4
3 + 7
Lch
1.0n LME49710NA
10u
6
4
680
100
6
0.1u
+
1.2k
10k
AOUTL+ +
220 LME49710NA
7
100u
+10u
1.0n
1.2k
680
0.1u
560
0.1u
560
100u
0.1u
10u
+
10u
0.1u
Figure 2. External Analog Filter
AKD4390-SA
40kHz (Double)
80kHz (quad)
Filter
Internal Filter
-0.3dB
-1dB
External LPF
-0.12dB
-1.3dB
Total
-0.42dB
-2.3dB
This table shows typical value.
Table 5. Frequency Responses
<KM093004>
4
2009/02
[AKD4390-SA]
Control Software Manual
„ Set-up of evaluation board and control software
1. Set up the AKD4390-SA according to previous term.
2. Connect IBM-AT compatible PC with AKD4390-SA by 10-line type flat cable (packed with AKD4390-SA). Take
care of the direction of 10pin header. (Please install the driver in the CD-ROM when this control software is used
on Windows 2000/XP. Please refer “Installation Manual of Control Software Driver by AKM device control
software”. In case of Windows95/98/ME, this installation is not needed. This control software does not operate on
Windows NT.)
3. Insert the CD-ROM labeled “AKD4390-SA Evaluation Kit” into the CD-ROM drive.
4. Access the CD-ROM drive and double-click the icon of “akd4390-SA.exe” to set up the control program.
5. Then please evaluate according to the follows.
„ Operation flow
Keep the following flow.
1. Set up the control program according to explanation above.
2. Click “Port Reset” button.
„ Explanation of each buttons
1. [Port Reset] :
2. [Write default] :
3. [All Write] :
4. [Function1] :
5. [Function2] :
6. [Function3] :
7. [Function4] :
8. [Function5]:
9. [SAVE] :
10. [OPEN] :
11. [Write] :
Set up the USB interface board (AKDUSBIF-A) .
Initialize the register of AK4390.
Write all registers that is currently displayed.
Dialog to write data by keyboard operation.
Dialog to write data by keyboard operation.
The sequence of register setting can be set and executed.
The sequence that is created on [Function3] can be assigned to buttons and
executed.
The register setting that is created by [SAVE] function on main window can
be assigned to buttons and executed.
Save the current register setting.
Write the saved values to all register.
Dialog to write data by mouse operation.
„ Indication of data
Input data is indicated on the register map. Red letter indicates “H” or “1” and blue one indicates “L” or “0”. Blank is
the part that is not defined in the datasheet.
<KM093004>
5
2009/02
[AKD4390-SA]
„ Explanation of each dialog
1. [Write Dialog] : Dialog to write data by mouse operation
There are dialogs corresponding to each register.
Click the [Write] button corresponding to each register to set up the dialog. If you check the check box, data
becomes “H” or “1”. If not, “L” or “0”.
If you want to write the input data to AK4390, click [OK] button. If not, click [Cancel] button.
2. [Function1 Dialog] : Dialog to write data by keyboard operation
Address Box:
Data Box:
Input registers address in 2 figures of hexadecimal.
Input registers data in 2 figures of hexadecimal.
If you want to write the input data to AK4390, click [OK] button. If not, click [Cancel] button.
3. [Function2 Dialog] : Dialog to evaluate ATT
Address Box:
Input registers address in 2 figures of hexadecimal.
Start Data Box:
Input starts data in 2 figures of hexadecimal.
End Data Box:
Input end data in 2 figures of hexadecimal.
Interval Box:
Data is written to AK4390 by this interval.
Step Box:
Data changes by this step.
Mode Select Box:
If you check this check box, data reaches end data, and returns to start data.
[Example]
Start Data = 00, End Data = 09
Data flow:
00 01 02 03 04 05 06 07 08 09 09 08 07 06 05 04 03 02 01 00
If you do not check this check box, data reaches end data, but does not return to start data.
[Example]
Start Data = 00, End Data = 09
Data flow:
00 01 02 03 04 05 06 07 08 09
If you want to write the input data to AK4390, click [OK] button. If not, click [Cancel] button.
<KM093004>
6
2009/02
[AKD4390-SA]
4. [Save] and [Open]
4-1. [Save]
Save the current register setting data. The extension of file name is “akr”.
(Operation flow)
(1) Click [Save] Button.
(2) Set the file name and push [Save] Button. The extension of file name is “akr”.
4-2. [Open]
The register setting data saved by [Save] is written to AK4390. The file type is the same as [Save].
(Operation flow)
(1) Click [Open] Button.
(2) Select the file (*.akr) and Click [Open] Button.
<KM093004>
7
2009/02
[AKD4390-SA]
5. [Function3 Dialog]
The sequence of register setting can be set and executed.
(1) Click [F3] Button.
(2) Set the control sequence.
Set the address, Data and Interval time. Set “-1” to the address of the step where the sequence should be paused.
(3) Click [Start] button. Then this sequence is executed.
The sequence is paused at the step of Interval="-1". Click [START] button, the sequence restarts from the paused step.
This sequence can be saved and opened by [Save] and [Open] button on the Function3 window. The extension of file
name is “aks”.
Figure 3. Window of [F3]
<KM093004>
8
2009/02
[AKD4390-SA]
6. [Function4 Dialog]
The sequence that is created on [Function3] can be assigned to buttons and executed. When [F4] button
is clicked, the window as shown in Figure opens.
Figure 4. [F4] window
<KM093004>
9
2009/02
[AKD4390-SA]
6-1. [OPEN] buttons on left side and [START] buttons
(1) Click [OPEN] button and select the sequence file (*.aks).
The sequence file name is displayed as shown in Figure .
Figure 5. [F4] window(2)
(2) Click [START] button, then the sequence is executed.
6-2. [SAVE] and [OPEN] buttons on right side
[SAVE] : The sequence file names can assign be saved. The file name is *.ak4.
[OPEN] : The sequence file names assign that are saved in *.ak4 are loaded.
6-3. Note
(1) This function doesn't support the pause function of sequence function.
(2) All files need to be in same folder used by [SAVE] and [OPEN] function on right side.
(3) When the sequence is changed in [Function3], the file should be loaded again in order to reflect the
change.
<KM093004>
10
2009/02
[AKD4390-SA]
7. [Function5 Dialog]
The register setting that is created by [SAVE] function on main window can be assigned to buttons and
executed. When [F5] button is clicked, the following window as shown in Figure opens.
Figure 6. [F5] window
7-1. [OPEN] buttons on left side and [WRITE] button
(1) Click [OPEN] button and select the register setting file (*.akr).
(2) Click [WRITE] button, then the register setting is executed.
7-2. [SAVE] and [OPEN] buttons on right side
[SAVE] : The register setting file names assign can be saved. The file name is *.ak5.
[OPEN] : The register setting file names assign that are saved in *.ak5 are loaded.
7-3. Note
(1) All files need to be in same folder used by [SAVE] and [OPEN] function on right side.
(2) When the register setting is changed by [Save] Button in main window, the file should be loaded again in
order to reflect the change.
<KM093004>
11
2009/02
[AKD4390-SA]
Measurement Results
[Measurement condition]
• Measurement unit
• MCLK
• BICK
• fs
• Bit
• Power Supply
• Interface
• Temperature
• Operational Amplifiers
: Audio Precision System two Cascade (AP2)
: 512fs (44.1kHz), 256fs (96kHz), 128fs (192kHz)
: 64fs
: 44.1kHz, 96kHz, 192kHz
: 24bit
: AVDD= DVDD=5V
: Internal DIR
: Room
: LME49710NA
fs=44.1kHz
Parameter
Input signal
Measurement filter
S/(N+D)
DR
1kHz, 0dB
1kHz, -60dB
20kLPF
S/N
“0” data
20kLPF, A-weighted
20kLPF
20kLPF, A-weighted
Parameter
Input signal
Measurement filter
S/(N+D)
DR
1kHz, 0dB
1kHz, -60dB
80kLPF
S/N
“0” data
80kLPF, A-weighted
80kLPF
80kLPF, A-weighted
Parameter
Input signal
Measurement filter
S/(N+D)
DR
1kHz, 0dB
1kHz, -60dB
80kLPF
S/N
“0” data
Results
Lch
104.0
116.1
118.3
116.2
118.5
Rch
103.9
116.1
118.2
116.2
118.5
fs=96kHz
Results
Lch
Rch
103.0
113.0
118.2
113.1
118.3
102.9
113.0
118.2
113.2
118.5
fs=192kHz
<KM093004>
80kLPF, A-weighted
80kLPF
80kLPF, A-weighted
12
Results
Lch
102.6
112.9
118.2
113.2
118.3
Rch
102.7
112.9
118.2
113.1
118.5
2009/02
[AKD4390-SA]
Plots
(fs=44.1kHz)
AKM
AK4390 FFT
fs=44.1kHz,0dBFS input
03/05/08 20:00:17
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 1 FFT (fin=1kHz, Input Level=0dBFS)
AKM
AK4390 FFT
fs=44.1kHz,-60dBFS input
03/05/08 20:09:03
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 2
<KM093004>
FFT (fin=1kHz, Input Level=-60dBFS)
13
2009/02
[AKD4390-SA]
(fs=44.1kHz)
AKM
AK4390 FFT
fs=44.1kHz,No signal input
03/05/08 20:09:46
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 3 FFT (Noise Floor)
AKM
AK4390 FFT Out of band noise
fs=44.1kHz,No signal input
03/05/08 20:11:26
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
50k
100k
Hz
Figure 4 FFT (Out of band noise)
<KM093004>
14
2009/02
[AKD4390-SA]
(fs=44.1kHz)
AKM
AK4390 THD+N vs. Input Level
fs=44.1kHz,fin=1kHz
03/05/08 20:15:06
-80
-85
-90
-95
-100
d
B
r
A
-105
-110
-115
-120
-125
-130
-135
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 5 THD+N vs. Input level (fin=1kHz)
AKM
AK4390 THD+N vs. Input Frequency
fs=44.1kHz,0dBFS Input
03/05/08 20:19:13
-80
-85
-90
-95
-100
d
B
r
A
-105
-110
-115
-120
-125
-130
-135
-140
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 6 THD+N vs. Input Frequency (Input level=0dBFS)
<KM093004>
15
2009/02
[AKD4390-SA]
(fs=44.1kHz)
AKM
AK4390 Linearity
fs=44.1kHz,fin=1kHz
03/05/08 20:29:50
+0
-10
-20
-30
-40
-50
-60
d
B
r
-70
-80
A
-90
-100
-110
-120
-130
-140
-150
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 7 Linearity (fin=1kHz)
AKM
AK4390 Frequency Response
fs=44.1kHz,0dBFS Input
08/05/08 15:09:13
+1
+0.8
+0.6
+0.4
+0.2
+0
-0.2
d
B
r
A
-0.4
-0.6
-0.8
-1
-1.2
-1.4
-1.6
-1.8
-2
2k
4k
6k
8k
10k
12k
14k
16k
18k
20k
Hz
Figure 8 Frequency Response (Input level=0dBFS)
<KM093004>
16
2009/02
[AKD4390-SA]
(fs=44.1kHz)
AKM
AK4390 Crosstalk
fs=44.1kHz,0dBFS Input
03/05/08 20:37:56
+0
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
-150
20
50
100
200
500
1k
2k
5k
10k
20k
Hz
Figure 9 Crosstalk (Input level=0dBFS)
<KM093004>
17
2009/02
[AKD4390-SA]
(fs=96kHz)
AKM
AK4390 FFT
fs=96kHz,0dBFS Input
03/05/08 20:41:54
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
40k
Hz
Figure 10 FFT (fin=1kHz, Input Level=0dBFS)
AKM
AK4390 FFT
fs=96kHz,-60dBFS Input
03/05/08 20:42:53
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
40k
Hz
Figure 11 FFT (fin=1kHz, Input Level=-60dBFS)
<KM093004>
18
2009/02
[AKD4390-SA]
(fs=96kHz)
AKM
AK4390 FFT
fs=96kHz,No signal input
03/05/08 20:43:29
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
40k
Hz
Figure 12 FFT (Noise Floor)
AKM
AK4390 THD+N vs. Input level
fs=96kHz,fin=1kHz
03/05/08 20:46:00
-80
-85
-90
-95
-100
d
B
r
A
-105
-110
-115
-120
-125
-130
-135
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 13 THD+N vs. Input level (fin=1kHz)
<KM093004>
19
2009/02
[AKD4390-SA]
(fs=96kHz)
AKM
AK4390 THD+N vs. Input Frequency
fs=96kHz,0dBFS Input
03/05/08 20:48:30
-80
-85
-90
-95
-100
d
B
r
A
-105
-110
-115
-120
-125
-130
-135
-140
20
50
100
200
500
1k
2k
5k
10k
20k
40k
Hz
Figure 14 THD+N vs. Input Frequency (Input level=0dBFS)
AKM
AK4390 Linearity
fs=96kHz,fin=1kHz
03/05/08 20:54:14
+0
-10
-20
-30
-40
-50
-60
d
B
r
-70
-80
A
-90
-100
-110
-120
-130
-140
-150
-150
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 15 Linearity (fin=1kHz)
<KM093004>
20
2009/02
[AKD4390-SA]
(fs=96kHz)
AKM
AK4390 Frequency Response
fs=96kHz,0dBFS Input
08/05/08 15:11:25
+1
+0.8
+0.6
+0.4
+0.2
+0
-0.2
d
B
r
A
-0.4
-0.6
-0.8
-1
-1.2
-1.4
-1.6
-1.8
-2
2.5k
5k
7.5k
10k
12.5k
15k
17.5k
20k
22.5k
25k
27.5k
30k
32.5k
35k
37.5k
40k
Hz
Figure 16 Frequency Response (Input level=0dBFS)
AKM
AK4390 Crosstalk
fs=96kHz,0dBFS Input
03/05/08 21:00:20
+0
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
-150
20
50
100
200
500
1k
2k
5k
10k
20k
40k
Hz
Figure 17 Crosstalk (Input level=0dBFS)
<KM093004>
21
2009/02
[AKD4390-SA]
(fs=192kHz)
AKM
AK4390 FFT
fs=192kHz,0dBFS Input
03/05/08 21:03:43
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
50k
80k
Hz
Figure 18 FFT (fin=1kHz, Input Level=0dBFS)
AKM
AK4390 FFT
fs=192kHz,-60dBFS
03/05/08 21:15:25
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
A
-80
-90
-100
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
50k
80k
Hz
Figure 19 FFT (fin=1kHz, Input Level=-60dBFS)
<KM093004>
22
2009/02
[AKD4390-SA]
(fs=192kHz)
AKM
AK4390 FFT
fs=192kHz,No Signal Input
03/05/08 21:12:43
+0
-10
-20
-30
-40
-50
-60
-70
d
B
r
-80
A
-100
-90
-110
-120
-130
-140
-150
-160
-170
-180
20
50
100
200
500
1k
2k
5k
10k
20k
50k
80k
Hz
Figure 20 FFT (Noise Floor)
AKM
AK4390 THD+N vs. Input Level
fs=192kHz,fin=1kHz
03/05/08 21:25:24
-80
-85
-90
-95
-100
d
B
r
A
-105
-110
-115
-120
-125
-130
-135
-140
-140
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 21 THD+N vs. Input level (fin=1kHz)
<KM093004>
23
2009/02
[AKD4390-SA]
(fs=192kHz)
AKM
AK4390 THD+N vs. Input Frequency
fs=192kHz,0dBFS Input
03/05/08 21:28:13
-80
-85
-90
-95
-100
d
B
r
A
-105
-110
-115
-120
-125
-130
-135
-140
20
50
100
200
500
1k
2k
5k
10k
20k
50k
80k
Hz
Figure 22 THD+N vs. Input Frequency (Input level=0dBFS)
AKM
AK4390 Linearity
fs=192kHz,fin=1kHz
03/06/08 12:02:35
+0
-10
-20
-30
-40
-50
d
B
r
-60
-70
A
-80
-90
-100
-110
-120
-130
-130
-120
-110
-100
-90
-80
-70
-60
-50
-40
-30
-20
-10
+0
dBFS
Figure 23 Linearity (fin=1kHz)
<KM093004>
24
2009/02
[AKD4390-SA]
(fs=192kHz)
AKM
AK4390 Frequency Response
fs=192kHz,0dBFS Input
08/05/08 15:13:37
+1
+0.8
+0.6
+0.4
+0.2
+0
-0.2
d
B
r
A
-0.4
-0.6
-0.8
-1
-1.2
-1.4
-1.6
-1.8
-2
-2.2
5k
10k
15k
20k
25k
30k
35k
40k
45k
50k
55k
60k
65k
70k
75k
80k
Hz
Figure 24 Frequency Response (Input level=0dBFS)
AKM
AK4390 Crosstalk
fs=192kHz,0dBFS Input
03/05/08 21:52:41
+0
-10
-20
-30
-40
-50
-60
d
B
-70
-80
-90
-100
-110
-120
-130
-140
-150
20
50
100
200
500
1k
2k
5k
10k
20k
50k
80k
Hz
Figure 25 Crosstalk (Input level=0dBFS)
<KM093004>
25
2009/02
[AKD4390-SA]
Revision History
Date
(YY/MM/DD)
08/07/18
Manual
Revision
KM093002
Board
Revision
2
08/08/05
09/02/27
KM093003
KM093004
2
2
Reason
Page
Contents
First edition
Change
8,16,24
Change
1
Modification
12
Figure 8, 16 and 24 were changed.
Block Diagram was changed.
Update of measurement results.
IMPORTANT NOTICE
• These products and their specifications are subject to change without notice. Before considering any use or
application, consult the Asahi Kasei EMD Corporation (EMD) sales office or authorized distributor
concerning their current status.
• EMD assumes no liability for infringement of any patent, intellectual property, or other right in the
application or use of any information contained herein.
• Any export of these products, or devices or systems containing them, may require an export license or
other official approval under the law and regulations of the country of export pertaining to customs and
tariffs, currency exchange, or strategic materials.
• EMD products are neither intended nor authorized for use as critical components in any safety, life support,
or other hazard related device or system, and EMD assumes no responsibility relating to any such use,
except with the express written consent of the Representative Director of EMD. As used here:
a. A hazard related device or system is one designed or intended for life support or maintenance of safety
or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to
function or perform may reasonably be expected to result in loss of life or in significant injury or
damage to person or property.
b. A critical component is one whose failure to function or perform may reasonably be expected to result,
whether directly or indirectly, in the loss of the safety or effectiveness of the device or system
containing it, and which must therefore meet very high standards of performance and reliability.
• It is the responsibility of the buyer or distributor of an EMD product who distributes, disposes of, or
otherwise places the product with a third party to notify that party in advance of the above content and
conditions, and the buyer or distributor agrees to assume any and all responsibility and liability for and hold
EMD harmless from any and all claims arising from the use of said product in the absence of such
notification.
<KM093004>
26
2009/02
5
4
3
VCC_R
VCC_R
2
1
VCC_R
C47
10u
D
+
D
PORT1
C49
0.1u
C48
0.1u
MCLK
BICK
LRCK
SDTO
1
2
3
4
5
10
9
8
7
6
18
17
B
U
C
20
19
VOUT
22
21
TVDD
TXP1
TX0
23
24
TXN1
25
TVSS
26
XTI1
27
XTO1
28
XTO2
XTI2
29
30
OVDD
EBICK
VCC_R
OVSS
32
31
EXT
C50
0.1u
R50
R51
R52
R53
(open)
(open)
(open)
(open)
VREFHL
R54
33
EMCK
LRCK
16
34
ELRCK
SDTO
15
R49
100
5.1
VREFHL
R55
100
R100
R56
MCKO2
11
39
OCKS1/CCLK/SCL
MCKO1
10
40
OCKS0/CSN/CAD0
DVSS
9
41
DVDD
DAUX
8
C57
C66
10u
42
DVSS
VIN
7
43
BVSS
DVDD
6
XSEL/RX7
5
+
0.1u
19
20
VSS2(VSSL)
AOUTLN
AVDD
21
22
23
24
MCLK
25
26
28
27
DVDD
VCC_R
C68
0.1u
PDN
AK4115
C67
0.1u
VSS3(AVSS)
+
VSS4(DVSS)
VCC_R
BICK/DCLK
10k
10u
C61
R60
(short) (short)
+
C64
0.1u
0.1u
0.1u
SDATA/DSDL
R62
10k
R59
10u
C62
10u
C63
30
38
LRCK/DSDR
R61
C60
C59
+
4
C58
10p
17
CM1/CDTI/SDA
R58
C65
10u
C
16
12
VREFLL
OVDD
VREFHL
CM0/CDTO/CAD1
1M
18
OVSS
37
(short)
R57
AOUTLP AOUTLN
VDDL
INT1
13
5.1
OCKS1
OCKS0 3
(short)
100
36
L
C
14
+
SW1
DSS102
BICK
29
H
INT0
AOUTLP
2
1
35
R101
VREFHL
R63
1M
U8
R65
AK4390
VREFHR
VREFLR
15
14
VDDR
VSS1(VSSR)
13
12
AOUTRN
10
11
AOUTRP
ACKS/DZFR
9
PSN
8
R67
100
(short)
R68
C70
0.1u
C72
R69
(short) (short)
R71
R102
1M
(short)
U7
MVDD
OUT
C77
0.1u
C81
10u
R74
R73
+
VCC_R
3
4
R76
(open)
VCC_R
SW2
R75 10k
(open)
C83
0.1u
NJM78M05
C200
100u
GND
T4
+
C78
4.7u
+
B
VREFHR
AOUTRP AOUTRN
C76
0.1u
R72
10k
C71
10u
0.1u
10u
1
IPS0/RX4
64
RX3
AVDD
63
AVSS
62
61
RX2
AVDD
60
59
RX1
58
RXP0
AVSS
57
56
55
54
53
P/SN
AVDD
VCOM
52
51
50
R
AVSS
49
RXN0
DIF0/RX5
ACKS
FILT
VREFHR
+
48
(short)
R64
1M
C69
R70
B
DIF2
2
DIF1/DZFL
TEST
7
XTL1
DIF0/CAD1
47
R66
6
3
5
DIF1/RX6
DEM1/CDT1
XTL0
DEM0/CCLK
46
4
4
3
PDN
DFS0/CAD0
PSEL
2
45
1
IPS1/IIC
+
VCC_R
SMUTE/CSN
5.1
44
IN
C79
0.1u
C80
0.1u
+
C82
470u
2
1
open
P/S
R77
R78
(open)
1M
U9
+
C85
0.1u
C84
10u
8
16
R79
12
4Y
9
3Y
7
2Y
G
A/B
15
1
4B
4A
3B
3A
2B
2A
1B
1A
13
14
10
11
6
5
3
2
1
(short)
GND
VCC
4
K
L1
R83
D1
HSU119
A
47u
PORT3
10k
1Y
74LVC157
U10
2
1
TORX141
C87
0.1u
+ C86
10u
R87
L
(open)
H
SW3
C88
J7
C89
0.1u
COAX
BNC-R-PC
R88
0
0.1u
2
ATE1D-2M3
AK4115,AK4390-PDN
R89
75
1A
2A
3A
4A
5A
6A
VCC
GND
1Y
2Y
3Y
4Y
5Y
6Y
2
4
6
8
10
12
T5
74HC14
OUT
C93
0.1u
C90
0.1u
uPC3533
GND
GND
OUT
1
3
5
9
11
13
14
7
1
3
3
VCC
470
R81
470
R82
CDTI
CCLK
470
R84
10k
2
A
PORT2
R80
CSN
1
3
5
7
9
2
4
6
8
10
uP-I/F
A
R85
10k
R86
10k
VCC_R
MVDD
IN
C91
0.1u
C92
47u
+
Title
Size
A2
Date:
5
4
3
2
AKD4390-SA
Document Number
Rev
2
Main
Sheet
Friday, July 18, 2008
1
1
of
3
5
4
3
2
1
C1
6.8n
2
C5
6.8n
-
LME49710NA
R6
620
C6
open
R8
680
R12
1200
C7
open
R10
short
D
2
6
3
R9
620
C10
100p
C8
short
U2
LME49710NA
R15
560
R11
100
R14
open
7
C9
100p
C4
1n
R7
short
+
7
C3
100p
R5
10k
6
4
C2
100u
D
R4
560
U1
+
4
+
3
+
R3
220
-
R2
220
AOUTLP
C12
1n
J1
LOUT
C11
open
C13
6.8n
+
7
R19
220
C
R20
10k
C16
6.8n
+
2
-
C15
100p
U3
6
R21
LME49710NA
4
C14
100u
3
R22
5.1
C
5.1
C21
100p
R24
1200
C17
0.1u
+
C18 C19
10u 0.1u
+
R23
680
T-45
C20
10u
J3
-15V
C22
100p
C23
470u
+
R29
220
6.8n
R30 C29
220
7
10k
R25
AOUTRN
C30
100u
3
+
2
-
10u
C25
0.1u
C26
+
10u
C27
R26
R27
5.1
U4
5.1
T-45
6
J4
LME49710NA
+15V
4
C31
100p
+
0.1u
C24
C28
6.8n
+
R18
220
AOUTLN
B
B
R33
560
C36
open
C37
open
R38
short
2
6
+
7
R44
220
AOUTRP
R46
10k
C42
100p
3
+
2
-
R45
560
LME49710NA
C43
1n
R39
100
R41
open
J6
ROUT
C40
open
6
LME49710NA
4
C41
100u
R37
620
U6
7
3
R43
220
C39
short
U5
+
C38
6.8n
R36
short
4
R35
620
C34
100p
+
R34
1200
-
C33
100p
C32
470u
C35
1n
+
R31
680
MVDD
C44
6.8n
A
A
C45
100p
R48
1200
R47
680
C46
100p
Title
Size
A3
Date:
5
4
3
2
AKD4390-SA
Document Number
Rev
2
External LPF
Friday, July 18, 2008
Sheet
1
2
of
3
5
4
3
MVDD
2
Q1
BCP 56
1
VREFHL
D
D
R90
R91
270
200
R103
1
R92
C107
100p
D2
C96
0.1u
+
3.83k
C94
100u
C95
0.1u
DIODE ZENER1
U11
R93
510 C108
1
NC
NC
8
2
-IN
V+
7
3
+IN
OUT
6
4
V-
NC
5
100p
+
C
+
AD817A/AD
C97
100u
C99
470u
C112
Q2
SB1188 CSC
C106
100p
C
+
D3
C98
100u
R94
3.6k
C100
100u
R95
3.6k
200p DIODE ZENER1
200p
+
+
470u
C101
DIODE ZENER1
D4
C109
100p
C102
100u
B
+
C113
U12
1
NC
8
-IN
V+
7
+IN
OUT
6
NC
5
NC
2
C111
3
100p
4
V-
B
Q3
SB1188 CSC
AD817A/AD
R96
510
D5
DIODE ZENER1
C110
R104
1
R97
R98
270
200
100p
C103
0.1u
R99
3.83k
+
C104
0.1u
C105
100u
A
A
VREFHR
Q4
BCP 56
MVDD
Title
Size
A3
Date:
5
4
3
2
AKD4390-SA
Document Number
Rev
2
Puwer Supply Unit
Friday, July 18, 2008
Sheet
1
3
of
3