Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Te ntative TFT LCD Tentative Specification MODEL NO.: G141I1 - L01 Customer: Approved by: Note: FOR MORE INFORMATION: AZ DISPLAYS, INC. 75 COLUMBIA, ALISO VIEJO, CA 92656 Http://www.AZDISPLAYS.com 記錄 工作 審核 角色 投票 2008-08-06 22:14:04 CST PMMD Director cs_lee(李志聖 /17564/44926) Director Accept 1 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative - CONTENTS REVISION HISTORY ------------------------------------------------------- 3 1. GENERAL DESCRIPTION ------------------------------------------------------- 4 ------------------------------------------------------- 6 ------------------------------------------------------- 7 ------------------------------------------------------- 11 ------------------------------------------------------- 12 ------------------------------------------------------- 15 ------------------------------------------------------- 17 ------------------------------------------------------- 21 ------------------------------------------------------- 22 ------------------------------------------------------- 24 ------------------------------------------------------- 25 1.1 OVERVIEW 1.2 FEATURES 1.3 APPLICATION 1.4 GENERAL SPECIFICATIONS 1.5 MECHANICAL SPECIFICATIONS 2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE 2.2.2 BACKLIGHT UNIT 3. ELECTRICAL CHARACTERISTICS 3.1 TFT LCD MODULE 3.2 BACKLIGHT UNIT 4. BLOCK DIAGRAM 4.1 TFT LCD MODULE 4.2 BACKLIGHT UNIT 5. INPUT TERMINAL PIN ASSIGNMENT 5.1 TFT LCD MODULE 5.2 BACKLIGHT UNIT 5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL 5.4 COLOR DATA INPUT ASSIGNMENT 6. INTERFACE TIMING 6.1 INPUT SIGNAL TIMING SPECIFICATIONS 6.2 POWER ON/OFF SEQUENCE 7. OPTICAL CHARACTERISTICS 7.1 TEST CONDITIONS 7.2 OPTICAL SPECIFICATIONS 8. PRECAUTIONS 8.1 ASSEMBLY HANDLING PRECAUTIONS 8.2 SAFETY PRECAUTIONS 9. PACKING 9.1 CARTON 9.2 PALLET 10. DEFINITION OF LABELS 10.1 CMO MODULE LABEL 11. MECHANICAL CHARACTERISTICS 2 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative REVISION HISTORY Version Date Ver 0.0 Jun. 18, 2008 Section All Description G141I1-L01 Tentative Spec. was first issued. 3 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 1. GENERAL DESCRIPTION 1.1 OVERVIEW G141I1 - L01 is a 14.1” TFT Liquid Crystal Display module and 20 pins LVDS interface. This module supports 1280 x 800 WXGA mode and can display 262,144 colors. The inverter module for Backlight is not built in. 1.2 FEATURES - WXGA (1280 x 800 pixels) resolution - DE only mode - LVDS interface - High brightness - High color saturation - High contrast ratio - Wide operating temperature range (-30℃ to 80℃) - Lamp replaceable - Sunlight readable - Reversible scan function - RoHS compliance 1.3 APPLICATION - TFT LCD Panel - Factory Application 1.4 GENERAL SPECIFICATI0NS Item Active Area Bezel Opening Area Driver Element Pixel Number Pixel Pitch Pixel Arrangement Display Colors Transmissive Mode Surface Treatment Specification 303.4 x 189.6 306.4 x 192.6 a-si TFT active matrix 1280xR.G.Bx800 0.237(H) x 0.237(V) RGB vertical stripe 262,144 Normally white Glare,3H,LR Unit mm mm pixel mm color - Note (1) - 4 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 1.5 MECHANICAL SPECIFICATIONS Item Min. Typ. Max. Unit Horizontal(H) 325.5 326 326.5 mm Module Size Vertical(V) 216 216.5 217 mm Depth(D) 15.5 16 16.5 mm Weight 1200 g I/F connector mounting position The mounting inclination of the connector makes the screen center within ±0.5mm as the horizontal. Note (1) (2) Note (1) Please refer to the attached drawings for more information of front and back outline dimensions. Note (2) Connector mounting position +/- 0.5mm 5 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 2. ABSOLUTE MAXIMUM RATINGS 2.1 ABSOLUTE RATINGS OF ENVIRONMENT Test Item High Temperature Storage Test Low Temperature Storage Test Thermal Shock Storage Test High Temperature Operation Test Low Temperature Operation Test High Temperature & High Humidity Operation Test Test Condition 90ºC, 240hours -40ºC, 240hours -40ºC, 0.5hour ~ 85ºC, 0.5hour, 100 cycles 80ºC, 240hours -30ºC, 240hours Note (1) (3) 60ºC 90%RH, 240hours 150pF, 330Ω, 1sec/cycle Condition 1 : panel contact, ±8KV (1) Condition 2 : panel non-contact ±15KV 50G, 11ms, half sine wave, 1 time for ± X, ± Y, ± Z direction (1)(2) 1.5G, 10 ~ 300 Hz sine wave, 10min/cycle, 3 cycles each X, (1)(2) Y, Z direction ESD Test (Operation) Shock (Non-Operating) Vibration (Non-Operating) Note (1) No display malfunctions. Note (2) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough so that the module would not be twisted or bent by the fixture. Note (3) Temperature of panel display surface area should be 85 ºC Max. Note (4) In the standard conditions, there is no function failure issue occurred. All the cosmetic specification is judged before the reliability test 2.2 ELECTRICAL ABSOLUTE RATINGS 2.2.1 TFT LCD MODULE Item Power Supply Voltage Logic Input Voltage Symbol VCC VIN Value Min. -0.3 -0.3 Unit Note V V (1) Unit Note VRMS mARMS KHz (1), (2), IL = 7.0 mA Max. +4.0 VCC+0.3 2.2.2 BACKLIGHT UNIT Item Lamp Voltage Lamp Current Lamp Frequency Symbol VL IL FL Value Min. Max. 2.5 7.5 80 40 (1), (2) Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation should be restricted to the conditions described under Normal Operating Conditions. Note (2) Specified values are for lamp (Refer to 3.2 for further information). 6 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 3. ELECTRICAL CHARACTERISTICS 3.1 TFT LCD MODULE Parameter Symbol Power Supply Voltage Permissive Ripple Voltage Rush Current Initial Stage Current White Power Supply Current Black Value Typ. 3.3 50 Min. 3.0 Vcc VRP IRUSH IIS (340) (440) Icc LVDS Differential Input High Threshold VTH(LVDS) LVDS Differential Input Low Threshold VTL(LVDS) -100 VCM |VID| RT PEBL 1.125 100 LVDS Common Mode Voltage LVDS Differential Input Voltage Terminating Resistor Power per EBL WG Unit Note 1.5 1.0 (380) (480) V mV A A mA mA +100 mV (2) (2) (3)a (3)b (5), VCM=1.2V (5) VCM=1.2V (5) (5) Max. 3.6 mV 1.375 600 100 TBD - - V mV Ohm W (4) Note (1) The ambient temperature is Ta = 25 ± 2 ºC. Note (2) IRUSH: the maximum current when Vcc is rising IIS: the maximum current of the first 100ms after power-on Measurement Conditions: Shown as the following figure. Test pattern: black. +3.3V Q1 2SK1475 Vcc C3 FUSE (LCD Module Input) 1uF R1 47K (High to Low) (Control Signal) Q2 R2 2SK1470 SW 1K +12V VR1 47K C2 C1 0.01uF 1uF Vcc rising time is 470us VCC +3.3V 0.9Vcc 100ms 470us 0V 0.1Vcc IIS IRUSH ICC 7 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative Note (3) The specified power supply current is under the conditions at Vcc = 3.3 V, Ta = 25 ± 2 ºC, fv = 60 Hz, whereas a power dissipation check pattern below is displayed. b. Black Pattern a. White Pattern Active Area Active Area Note (4) The specified power are the sum of LCD panel electronics input power and the inverter input power. Test conditions are as follows. (a) Vcc = 3.3 V, Ta = 25 ± 2 ºC, fv = 60 Hz, (b) The pattern used is a black and white 32 x 36 checkerboard, slide #100 from the VESA file “Flat Panel Display Monitor Setup Patterns”, FPDMSU.ppt. (c) Luminance: 60 nits. (d) The inverter used is provided from ”Darfon VK16165.101” Please contact them for detail information. CMO doesn’t provide the inverter in this product. Note (5) The parameters of LVDS signals are defined as the following figures. |VID| VCM Single Ended 0V VTH(LVDS) Differential |VID| 0V VTL(LVDS) 8 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 3.2 BACKLIGHT UNIT Parameter Ta = 25 ± 2 ºC Symbol Lamp Input Voltage Lamp Current VL IL Lamp Turn On Voltage VS Operating Frequency Lamp Life Time Power Consumption FL LBL PL Value Typ. 560 7.0 Min. -- Max. 1150(25 oC ) 1370( 0 oC) 40 50000 15.68 Unit Note VRMS mARMS VRMS VRMS KHz Hrs W IL = 7.0 mA (1) (2) (2) (3) (5) (4), IL = 7.0 mA Note (1) Lamp current is measured by utilizing a high frequency current meter as shown below: HV (Pink) LV (White) LCD Module 1 2 A Inverter HV (Blue) LV (Black) 1 2 A Current Meter YOKOGAWA 2016 A Note (2) The voltage that must be larger than Vs should be applied to the lamp for more than 1 second after startup. Otherwise, the lamp may not be turned on normally. Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the display, and this may cause line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronous frequency and its harmonics as far as possible. Note (4) PL = IL x VL x 4CCLFs Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition Ta = 25 ±2 oC and IL = 6.5 mArms until one of the following events occurs: (a) When the brightness becomes or lower than 50% of its original value. (b) When the effective ignition length becomes ≦ 80% of its original value. (The effective ignition length is a scope that luminance is over 70% of that at the center point.) Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the inverter must have specifications for the modularized lamp. The performance of the Backlight, such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for the lamp. All the parameters of an inverter should be carefully designed to avoid producing too much current leakage from high voltage output of the inverter. When designing or ordering the inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module should be operated in the same manners when it is installed in your instrument. The output of the inverter must have symmetrical (negative and positive) voltage waveform and 9 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its leakage current. a. The asymmetry rate of the inverter waveform should be 10% below. b. The distortion rate of the waveform should be within √2 ± 10%. c. The ideal sine wave form shall be symmetric in positive and negative polarities. * Asymmetry rate: Ip | I p – I –p | / Irms * 100% I -p * Distortion rate I p (or I –p) / Irms 10 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 4. BLOCK DIAGRAM 4.1 TFT LCD MODULE LVDS Display GND Reverse VL DC/DC CONVERTER & REFERENCE VOLTAGE GENERATOR LAMP CONNECTOR (YEONHO 35001HS-02L) SCAN DRIVER IC Vcc INPUT CONNECTOR (FI-SE20P-HFE (JAE)) Data & Clock LVDS INPUT / TIMING CONTROLLER TFT LCD PANEL (1280xR.G.B.x800) DATA DRIVER IC BACKLIGHT UNIT 4.2 BACKLIGHT UNIT 1 HV(Pink) 2 LV(White) 1 HV(Blue) 2 LV(Black) 1 HV(Pink) 2 LV(White) 1 HV(Blue) 2 LV(Black) Note：On the same side, the same polarity lamp voltage design for lamps is recommended 11 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 5. INPUT TERMINAL PIN ASSIGNMENT 5.1 TFT LCD MODULE Pin Pin 1 2 3 4 5 6 7 Symbol Symbol VCCS VCCS GND GND RX0RX0+ GND Description Description Power Supply +3.3 V (typical) Power Supply +3.3 V (typical) Ground Ground LVDS Differential Data Input LVDS Differential Data Input Ground Polarity Polarity Remark Remark Negative Positive R0~R5,G0 8 RX1- LVDS Differential Data Input Negative 9 10 RX1+ GND LVDS Differential Data Input Ground Positive 11 RX2- LVDS Differential Data Input Negative 12 13 14 15 16 17 18 RX2+ GND CLKCLK+ GND NC NC LVDS Differential Data Input Ground LVDS Clock Data Input LVDS Clock Data Input Ground Non-Connection Non-Connection Positive 19 Reverse 20 NC G1~G5, B0, B1 +3.3VReverse, GND/NC No Reverse Negative Positive B2~B5, DE, Hsync, Vsync LVDS Level Clock Refer to 6.2 POWER ON/OFF SEQUENCE Note(5) Non-Connection Note (1) Connector Part No.: FI-SE20P-HFE(JAE) or equivalent Note (2) User’s connector Part No: FI-SE20ME (JAE) or equivalent Note (3) The first pixel is odd as shown in the following figure. 12 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative Note (4) Scanning direction: The following figures are seen from a front view and the arrow shows the direction of scan. Reverse = GND/NC : normal display (default) Reverse = High : display with 180 degree rotation 5.2 BACKLIGHT UNIT Pin 1 2 Symbol HV LV Description High Voltage Ground Color Pink White Note (1) Connector Part No.: YEONHO 35001HS-02L or equivalent Note (2) User’s connector Part No.: YEONHO 35001 WR-02L or equivalent 5.3 TIMING DIAGRAM OF LVDS INPUT SIGNAL CLK+ T/7 Rxin2 Rxin1 Rxin0 IN20 IN19 IN18 IN17 IN16 IN15 IN14 DE Vsync Hsync B5 B4 B3 B2 IN13 IN12 IN11 IN10 IN9 IN8 IN7 B1 B0 G5 G4 G3 G2 G1 IN6 IN5 IN4 IN3 IN2 IN1 IN0 G0 R5 R4 R3 R2 R1 R0 Signal for 1 DCLK Cycle (T) 13 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 5.4 COLOR DATA INPUT ASSIGNMENT The brightness of each primary color (red, green and blue) is based on the 6-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input. Data Signal Red Green Blue R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Green 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Colors Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Yellow 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Red(0)/Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red(1) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Gray Red(2) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Scale : : : : : : : : : : : : : : : : : : : Of : : : : : : : : : : : : : : : : : : : Red Red(61) 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Red(62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Red(63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Green(0)/Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green(1) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Gray Green(2) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 Scale : : : : : : : : : : : : : : : : : : : Of : : : : : : : : : : : : : : : : : : : Green Green(61) 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0 Green(62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 Green(63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Blue(0)/Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Gray Blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 Scale : : : : : : : : : : : : : : : : : : : Of : : : : : : : : : : : : : : : : : : : Blue Blue(61) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 Blue(62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 Blue(63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Color Note (1) 0: Low Level Voltage, 1: High Level Voltage 14 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 6. INTERFACE TIMING 6.1 INPUT SIGNAL TIMING SPECIFICATIONS The specifications of input signal timing are as the following table and timing diagram. Signal DCLK Item Frequency Vertical Total Time Vertical Active Display Period Vertical Active Blanking Period Horizontal Total Time Horizontal Active Display Period Horizontal Active Blanking Period DE Note (1) Symbol 1/Tc TV TVD TVB TH THD THB Min. Typ. (63.9) 71 802 823 800 800 TV-TVD 23 1360 1440 1280 1280 TH-THD 160 Max. (74.5) 1030 800 TV-TVD 1600 1280 TH-THD Unit MHz TH TH TH Tc Tc Tc Note - Because this module is operated by DE only mode, Hsync and Vsync are ignored. INPUT SIGNAL TIMING DIAGRAM Tv TVD DE TH DCLK TC THD DE DATA 15 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 6.2 POWER ON/OFF SEQUENCE Power Off Power On 90% 90% -Power Supply for LCD, Vcc 0V Restart t7 10% 10% 10% t1 t4 -Reverse (Enable Pin) 0V t2 -LVDS interface t3 Valid Data 0V t5 t6 50% -Power for Lamp 50% OFF ON OFF Timing Specifications: 0.5 ≦ t1 ≦ 10 ms 0 ≦ t2 ≦ 50 ms 0 ≦ t3 ≦ 50 ms t4 ≧ 500 ms t5 ≧ 200 ms t6 ≧ 200 ms Note (1) Please follow the power on/off sequence described above. Otherwise, the LCD module might be damaged. Note (2) Please avoid floating state of interface signal at invalid period. When the interface signal is invalid, be sure to pull down the power supply of LCD Vcc to 0 V. Note (3) The Backlight inverter power must be turned on after the power supply for the logic and the interface signal is valid. The Backlight inverter power must be turned off before the power supply for the logic and the interface signal is invalid. Note (4) Sometimes some slight noise shows when LCD is turned off (even backlight is already off). To avoid this phenomenon, we suggest that the Vcc falling time is better to follow 5≦t7≦300 ms. Note (5) Reverse Pin not change signal when Panel Normal Displaying. 16 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 7. OPTICAL CHARACTERISTICS 7.1 TEST CONDITIONS Item Ambient Temperature Ambient Humidity Supply Voltage Input Signal Inverter Current Inverter Driving Frequency Inverter Symbol Value Unit o Ta C 25±2 Ha %RH 50±10 VCC 3.3 V According to typical value in "3. ELECTRICAL CHARACTERISTICS" IL 7 mA FL 61 KHz Darfon VK13165.101 The relative measurement methods of optical characteristics are shown in 7.2. The following items should be measured under the test conditions described in 7.1 and stable environment shown in Note (6). 7.2 OPTICAL SPECIFICATIONS Item Contrast Ratio Response Time Center Luminance of White White Variation Red Color Chromaticity Green Blue White Horizontal Viewing Angle Vertical Symbol CR TR TF LCEN δW Rx Ry Gx Gy Bx By Wx Wy θx+ θxθY+ θY- Condition Min. 500 500 θx=0°, θY =0° Viewing Normal Angle Typ0.03 CR≥10 70 70 60 60 Typ. 700 5 11 600 1.25 Max. 10 16 1.4 (0.618) (0.343) (0.306) (0.587) Typ+ (0.145) 0.03 (0.103) (0.313) (0.329) 80 80 70 70 Unit ms ms cd/m2 - Note (2), (5) (3) (4), (5) (5), (6) (1) Deg. 17 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative Note (1) Definition of Viewing Angle (θx, θy): Normal θx = θy = 0º θyθX- = 90º θy+ 12 o’clock direction x- y+ θx− 6 o’clock θx+ y- θy+ = 90º x+ θy- = 90º θX+ = 90º Note (2) Definition of Contrast Ratio (CR): The contrast ratio can be calculated by the following expression. Contrast Ratio (CR) = L63 / L0 L63: Luminance of gray level 63 L 0: Luminance of gray level 0 CR = CR (5) CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6). Note (3) Definition of Response Time (TR, TF) and measurement method: Gray Level 63 Gray Level 63 100% 90% Optical Response Gray Level 0 10% 0% Time TF TR 66.67 ms 66.67 ms 18 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative Note (4) Definition of Average Luminance of White (LCEN): Measure the luminance of gray level 63 at 5 points LCEN = L (5) L (x) is corresponding to the luminance of the point X at Figure in Note (6). Note (5) Measurement Setup: The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room. LCD Module LCD Panel Center of the Screen USB2000 CS-1000T Field of View = 2º Light Shield Room 500 mm (Ambient Luminance < 2 lux) 19 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative Note (6) Definition of White Variation (δW): Measure the luminance of gray level 63 at 5 points δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)] Horizontal Line D Vertical Line D/4 W/4 W D/2 1 W/2 3D/4 2 X 5 : Test Point X=1 to 5 3W/4 4 3 Active Area 20 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 8. PRECAUTIONS 8.1 ASSEMBLY AND HANDLING PRECAUTIONS (1) Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil may cause electrical short or worsen the polarizer. (3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will be damaged. (4) Always follow the correct power sequence when LCD module is connecting and operating. This can prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage LCD module when it is operating. (9) High temperature or humidity may reduce the performance of module. Please store LCD module within the specified storage conditions. (10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the response time will become slowly, and the starting voltage of CCFL will be higher than room temperature. 8.2 SAFETY PRECAUTIONS (1) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while assembling with inverter. Do not disassemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap. (3) After the module’s end of life, it is not harmful in case of normal operation and storage. 21 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 9. PACKAGING 9.1 CARTON Figure. 8-1 Packing method 22 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 9.2 PALLET Figure. 9-2 Packing method Figure. 9-3 Packing method 23 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0 Issued Date: Jun. 18, 2008 Model No.: G141I1 - L01 Tentative 10. DEFINITION OF LABELS 10.1 CMO MODULE LABEL The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation. E207943 CHI MEI OPTOELECTRONICS G141I1 -L01 Rev.XX MADE IN TAIWAN RoHS XXXXXXXYMDLNNNN (a) Model Name: G141I1 - L01 (b) Revision: Rev. XX, for example: A1, …C1, C2 …etc. (c) Serial ID: X X X X X X X Y M D X N N N N Serial No. CMO Internal Use Year, Month, Date CMO Internal Use Revision CMO Internal Use Serial ID includes the information as below: (a) Manufactured Date: Year: 1~9, for 2001~2009 Month: 1~9, A~C, for Jan. ~ Dec. Day: 1~9, A~Y, for 1st to 31st, exclude I , O and U (b) Revision Code: cover all the change (c) Serial No.: Manufacturing sequence of product 24 / 26 The information described in this technical specification is tentative and it is possible to be changed without prior notice. Please contact CMO ’s representative while your product design is based on this specification. Version 0.0