DUAL Series • Independently controlled dual output solid-state relay • Ratings from 25A to 40A @ 24-530 VAC • Industry standard package • SCR output for heavy industrial loads • DC Control • Zero-crossing (resistive loads) or random-fire (inductive loads) output PRODUCT SELECTION Control Voltage 4-15 VDC 15-32 VDC 4-15 VDC 15-32 VDC 25A 40A D2425D D2425DE H12D4825D H12D4825DE D2440D D2440DE H12D4840D H12D4840DE AVAILABLE OPTIONS OUTPUT SPECIFICATIONS (1) Description Operating Voltage (47-63Hz) [Vrms] Transient Overvoltage [Vpk] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2) Maximum Load Current (3) [Arms] Minimum Load Current [Arms] Maximum 1 Cycle Surge Current (50/60Hz) [Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case (Rjc) [°C/W] Maximum 1/2 Cycle I²t for Fusing (50/60 Hz) [A² sec] Minimum Power Factor (with Maximum Load) D2425xx D2440xx H12D4825xx H12D4840xx 24-280 600 10 500 24-280 600 10 500 48-530 1200 10 500 48-530 1200 10 500 25 0.15 239/250 1.6 1.02 285/259 0.5 40 0.15 597/625 1.6 0.63 1779/1621 0.5 25 0.15 239/250 1.6 1.02 285/259 0.5 40 0.15 597/625 1.6 0.63 1779/1621 0.5 INPUT SPECIFICATIONS (1) Description Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Typical Input Current @ 5 VDC (@ 24 VDC for E-Suffix) Nominal Input Impedance Maximum Turn-On Time [msec] (4) Maximum Turn-Off Time [msec] D24XXD H12D48XXD E-SUFFIX 4-15 VDC 4.0 VDC 1.0 VDC 13 mA 300 Ohm 1/2 cycle 1/2 cycle 4-15 VDC 4.0 VDC 1.0 VDC 13 mA 240 Ohm 1/2 cycle 1/2 cycle 15-32 VDC 15.0 VDC 1.0 VDC 15 mA 1500 Ohm 1/2 cycle 1/2 cycle GENERAL SPECIFICATIONS Description Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 V DC) Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation Terminals GENERAL NOTES 1) All parameters at 25°C and per section unless otherwise specified. 3) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Heat sinking required, for derating curves see next page. 4) Turn-on time for random turn-on (-10) versions is 0.1 msec MECHANICAL SPECIFICATIONS Parameters 4000 Vrms 109 Ohm 10 pF -40 to 80°C -40 to 125 °C 3.0 oz (86.5g) Thermally conductive Epoxy .25" Fastons, .025" Square Pins WIRING DIAGRAM THERMAL DERATE INFORMATION AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 E116949 (except 15-32VDC control) LR81689 (240 V, 4-15VDC control only) 5902 UG Rev. 121211 ANNEX - ENVIROMENTAL INFORMATION