DS5001FP 128k Soft Microprocessor Chip www.maxim-ic.com § § § PIN CONFIGURATIONS 8051-Compatible Microprocessor Adapts to Its Task - Accesses up to 128kB of nonvolatile SRAM - In-system programming through on-chip serial port - Can modify its own program or data memory - Accesses memory on a separate byte-wide bus - Performs CRC-16 check of NV RAM memory - Decodes memory and peripheral chip enables High-Reliability Operation – Maintains all nonvolatile resources for over 10 years – Power-fail reset – Early warning power-fail interrupt – Watchdog timer – Lithium backs user SRAM for program/data storage – Precision bandgap reference for power monitor Fully 8051 Compatible – 128kB scratchpad RAM – Two timer/counters – On-chip serial port – 32 parallel I/O port pins Software Security Available with DS5002FP Secure Microprocessor TOP VIEW 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 P0.4AD4 CE2 PE2 BA9 P0.3/AD3 BA8 P0.2/AD2 BA13 P0.1/AD1 R/W P0.0/AD0 VCC0 VCC MSEL P1.0 BA14 P1.1 BA12 P1.2 BA7 P1.3 PE3 PE4 BA6 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DS5001FP 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 P2.6/A14 CE3 CE4 BD3 P2.5/A13 BD2 P2.4/A12 BD1 P2.3/A11 BD0 VLI BA15 GND P2.2/A10 P2.1/A9 P2.0/A8 XTAL1 XTAL2 P3.7/RD P3.6/WR P3.5/TI PF VRST P3.4/T0 P1.4 BA5 P1.5 BA4 P1.6 BA3 P1.7 PROG BA2 RST BA1 P3.0/RXD BA0 P3.1/TXD P3.2/INT0 P3.3/INT1 § BA11 P0.5/AD5 PE1 P0.6/AD6 BA10 P0.7/AD7 CE1 N.C. CE1N BD7 ALE BD6 PSEN BD5 P2.7/A15 BD4 FEATURES MQFP This data sheet must be used in conjunction with the Secure Microcontroller User’s Guide, available on our website at www.maxim-ic.com/microcontrollers. The user’s guide contains operating information, whereas the data sheet contains ordering information, pinout, and electrical specifications MQFP Note: Some revisions of this device may incorporate deviations from published specifications known as errata. Multiple revisions of any device may be simultaneously available through various sales channels. For information about device errata, click here: www.maxim-ic.com/errata. 1 of 27 REV: 070605 DS5001FP ORDERING INFORMATION PART TEMP RANGE DS5001FP-16 DS5001FP-16+ DS5001FP-16N DS5001FP-16N+ DS5001FP-12-44 DS5001FP-12-44+ 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C 0°C to +70°C 0°C to +70°C MAX CLOCK SPEED (MHz) 16 16 16 16 12 12 PINPACKAGE 80 MQFP 80 MQFP 80 MQFP 80 MQFP 44MQFP 44 MQFP + Denotes a Pb-free/RoHS-compliant device. DESCRIPTION The DS5001FP 128k soft microprocessor chip is an 8051-compatible microprocessor based on NV RAM technology and designed for systems that need large quantities of nonvolatile memory. It provides full compatibility with the 8051 instruction set, timers, serial port, and parallel I/O ports. By using NV RAM instead of ROM, the user can program and then reprogram the microprocessor while in-system. The application software can even change its own operation, which allows frequent software upgrades, adaptive programs, customized systems, etc. In addition, by using NV SRAM, the DS5001FP is ideal for data logging applications. It also connects easily to a Dallas real-time clock. The DS5001FP provides the benefits of NV RAM without using I/O resources. It uses a nonmultiplexed byte-wide address and data bus for memory access. This bus performs all memory access and provides decoded chip enables for SRAM, which leaves the 32 I/O port pins free for application use. The DS5001FP uses ordinary SRAM and battery-backs the memory contents for over 10 years at room temperature with a small external battery. A DS5001FP also provides high-reliability operation in harsh environments. These features include the ability to save the operating state, power-fail reset, power-fail interrupt, and watchdog timer. A user programs the DS5001FP through its on-chip serial bootstrap loader. The bootstrap loader supervises the loading of software into NV RAM, validates it, and then becomes transparent to the user. Software can be stored in multiple 32kB or one 128kB CMOS SRAM(s). Using its internal partitioning, the DS5001FP can divide a common RAM into user-selectable program and data segments. This partition can be selected at program loading time, but can then be modified later at any time. The microprocessor decodes memory access to the SRAM and addresses memory through its byte-wide bus. Memory portions designated code or ROM are automatically write-protected by the microprocessor. Combining program and data storage in one device saves board space and cost. The DS5001FP offers several bank switches for access to even more memory. In addition to the primary data area of 64kB, a peripheral selector creates a second 64kB data space with four accompanying chip enables. This area can be used for memory-mapped peripherals or more data storage. The DS5001FP can also use its expanded bus on ports 0 and 2 (like an 8051) to access an additional 64kB of data space. Lastly, the DS5001FP provides one additional bank switch that changes up to 60kB of the NV RAM program space into data memory. Thus, with a small amount of logic, the DS5001 accesses up to 252kB of data memory. The DS2251T is available (Refer to the data sheet at www.maxim-ic.com/microcontrollers.) for users who want a preconstructed module using the DS5001FP, RAM, lithium cell, and a real-time clock. For more details, refer to the Secure Microcontroller User’s Guide. For users desiring software security, the DS5002FP is functionally identical to the DS5001FP but provides superior firmware security. The 44-pin version of the device is functionally identical to the 80-pin version but sports a reduced pin count and footprint. 2 of 27 DS5001FP Figure 1. BLOCK DIAGRAM 3 of 27 DS5001FP PIN DESCRIPTION PIN 80 PIN 44 PIN 11, 9, 7, 31 5, 1, 79, (P0.5) 77, 75 15, 17, 19, 21, 44 25, 27, (P1.3) 29, 31 49, 50, 51, 56, — 58, 60, 64, 66 NAME FUNCTION P0.0– P0.7 General-Purpose I/O Port 0. This port is open-drain and cannot drive a logic 1. It requires external pullups. Port 0 is also the multiplexed expanded address/data bus. When used in this mode, it does not require pullups. P1.0– P1.7 General-Purpose I/O Port 1 P2.0– P2.7 General-Purpose I/O Port 2. Also serves as the MSB of the address in expanded memory accesses, and as pins of the RPC mode when used. P3.0/RX D General-Purpose I/O Port Pin 3.0. Also serves as the receive signal for the on board UART. This pin should not be connected directly to a PC COM port. P3.1/TX D P3.2/ General-Purpose I/O Port Pin 3.1. Also serves as the transmit signal for the on board UART. This pin should not be connected directly to a PC COM port. 36 8 38 10 39 — 40 11 41 — P3.4/T0 44 12 P3.5/T1 45 13 P3.6/ WR 46 — P3.7/ RD 68 25 PSEN 34 6 RST 70 27 ALE 47, 48 14, 15 52 16 XTAL2, XTAL1 GND 13 39 VCC Power Supply, +5V INT0 P3.3/ INT1 General-Purpose I/O Port Pin 3.2. Also serves as the active-low external interrupt 0. General-Purpose I/O Port Pin 3.3. Also serves as the active-low external interrupt 1. General-Purpose I/O Port Pin 3.4. Also serves as the timer 0 input. General-Purpose I/O Port Pin 3.5. Also serves as the timer 1 input. General-Purpose I/O Port Pin. Also serves as the write strobe for expanded bus operation. General-Purpose I/O Port Pin. Also serves as the read strobe for expanded bus operation. Program Store Enable. This active-low signal is used to enable an external program memory when using the expanded bus. It is normally an output and should be unconnected if not used. PSEN also is used to invoke the bootstrap loader. At this time, PSEN is pulled down externally. This should only be done once the DS5001FP is already in a reset state. The device that pulls down should be open drain since it must not interfere with PSEN under normal operation. Active-High Reset Input. A logic 1 applied to this pin will activate a reset state. This pin is pulled down internally so this pin can be left unconnected if not used. An RC power-on reset circuit is not needed and is not recommended. Address Latch Enable. Used to demultiplex the multiplexed expanded address/data bus on port 0. This pin is normally connected to the clock input on a ’373 type transparent latch. Crystal Connections. Used to connect an external crystal to the internal oscillator. XTAL1 is the input to an inverting amplifier and XTAL2 is the output. Logic Ground 12 38 VCCO VCC Output. This is switched between VCC and VLI by internal circuits based on the level of VCC. When power is above the lithium input, power will be drawn from VCC. The lithium cell remains isolated from a load. When VCC is below VLI, the VCCO switches to the VLI source. VCCO should be connected to the VCC pin of an SRAM. 54 17 VLI Lithium Voltage Input. Connect to a lithium cell greater than VLIMIN and no greater than VLImax as shown in the electrical specifications. Nominal value is +3V. 4 of 27 DS5001FP PIN DESCRIPTION (continued) PIN 80 PIN 44 PIN 53, 16, 41, 36, 8, 18, 42, 32, 80, 76, 30, 34, 4, 6, 20, 35, 43, 24, 26, 1, 2, 3, 28, 30, 4, 5, 7, 33, 35, 9 37 71, 69, 28, 26, 67, 65, 24, 23, 61, 59, 21, 20, 57, 55 19, 18 NAME FUNCTION BA14– BA0 Byte-Wide Address Bus Bits 14–0. This bus is combined with the nonmultiplexed data bus (BD7–0) to access NV SRAM. Decoding is performed using CE1 through CE4 . Therefore, BA15 is not actually needed. Read/write access is controlled by R/ W . BA14–0 connect directly to an 8k, 32k, or 128k SRAM. If an 8k RAM is used, BA13 and BA14 are unconnected. If a 128k SRAM is used, the micro converts CE2 and CE3 to serve as A16 and A15 respectively. BD7–0 10 37 R/ W 74 29 CE1 72 — CE1N 2 33 CE2 63 22 CE3 62 — CE4 78 — PE1 3 — PE2 22 — PE3 23 — PE4 32 — PROG Byte-Wide Data Bus Bits 7–0. This 8-bit, bidirectional bus is combined with the nonmultiplexed address bus (BA14–0) to access NV SRAM. Decoding is performed on CE1 and CE2 . Read/write access is controlled by R/ W . BD7–0 connect directly to an SRAM, and optionally to a real-time clock or other peripheral. Read/Write. This signal provides the write enable to the SRAMs on the byte-wide bus. It is controlled by the memory map and partition. The blocks selected as program (ROM) are write-protected. Chip Enable 1. This is the primary decoded chip enable for memory access on the byte-wide bus. It connects to the chip enable input of one SRAM. CE1 is lithiumbacked. It remains in a logic high inactive state when VCC falls below VLI. Non-Battery-Backed Version of Chip Enable 1. This can be used with a 32kB EPROM. It should not be used with a battery-backed chip. Chip Enable 2. This chip enable is provided to access a second 32k block of memory. It connects to the chip enable input of one SRAM. When MSEL = 0, the micro converts CE2 into A16 for a 128k x 8 SRAM. CE2 is lithium-backed and remains at a logic high when VCC falls below VLI. Chip Enable 3. This chip enable is provided to access a third 32k block of memory. It connects to the chip enable input of one SRAM. When MSEL = 0, the micro converts CE3 into A15 for a 128k x 8 SRAM. CE3 is lithium-backed and remains at a logic high when VCC falls below VLI. Chip Enable 4. This chip enable is provided to access a fourth 32k block of memory. It connects to the chip-enable input of one SRAM. When MSEL = 0, this signal is unused. CE4 is lithium-backed and remains at a logic high when VCC < VLI. Peripheral Enable 1. Accesses data memory between addresses 0000h and 3FFFh when the PES bit is set to a logic 1. Commonly used to chip enable a byte-wide realtime clock such as the DS1283. PE1 is lithium-backed and remains at a logic high when VCC falls below VLI. Connect PE1 to battery-backed functions only. Peripheral Enable 2. Accesses data memory between addresses 4000h and 7FFFh when the PES bit is set to a logic 1. PE2 is lithium-backed and remains at a logic high when VCC falls below VLI. Connect PE2 to battery-backed functions only. Peripheral Enable 3. Accesses data memory between addresses 8000h and BFFFh when the PES bit is set to a logic 1. PE3 is not lithium-backed and can be connected to any type of peripheral function. If connected to a battery-backed chip, it needs additional circuitry to maintain the chip enable in an inactive state when VCC < VLI. Peripheral Enable 4. Accesses data memory between addresses C000h and FFFFh when the PES bit is set to a logic 1. PE4 is not lithium-backed and can be connected to any type of peripheral function. If connected to a battery-backed chip, it needs additional circuitry to maintain the chip enable in an inactive state when VCC < VLI. Invokes the bootstrap loader on a falling edge. This signal should be debounced so that only one edge is detected. If connected to ground, the micro enters bootstrap loading on power-up. This signal is pulled up internally. 5 of 27 DS5001FP PIN DESCRIPTION (continued) PIN 80 PIN 44 PIN NAME 42 — VRST 43 — PF 14 40 MSEL 73 — N.C. FUNCTION This I/O pin (open drain with internal pullup) indicates that the power supply (VCC) has fallen below the VCCmin level and the micro is in a reset state. When this occurs, the DS5001FP drives this pin to a logic 0. Because the micro is lithiumbacked, this signal is guaranteed even when VCC = 0V. Because it is an I/O pin, it also forces a reset if pulled low externally. This allows multiple parts to synchronize their power-down resets. This output goes to a logic 0 to indicate that VCC < VLI and the micro has switched to lithium backup. Because the micro is lithium-backed, this signal is guaranteed even when VCC = 0V. The normal application of this signal is to control lithium-powered current to isolate battery-backed functions from non-battery-backed functions. Memory Select. This signal controls the memory size selection. When MSEL = +5V, the DS5001FP expects to use 32k x 8 SRAMs. When MSEL = 0V, the DS5001FP expects to use a 128k x 8 SRAM. MSEL must be connected regardless of partition, mode, etc. No Connection INSTRUCTION SET The DS5001FP executes an instruction set that is object code-compatible with the industry standard 8051 microcontroller. As a result, software development packages such as assemblers and compilers that have been written for the 8051 are compatible with the DS5001FP. A complete description of the instruction set and operation are provided in the Secure Microcontroller User’s Guide. Also note that the DS5001FP is embodied in the DS2251T module. The DS2251T combines the DS5001FP with between 32k and 128k of SRAM, a lithium cell, and a real-time clock. This is packaged in a 72-pin SIMM module. MEMORY ORGANIZATION Figure 2 illustrates the memory map accessed by the DS5001FP. The entire 64k of program and 64k of data are potentially available to the byte-wide bus. This preserves the I/O ports for application use. The user controls the portion of memory that is actually mapped to the byte-wide bus by selecting the program range and data range. Any area not mapped into the NV RAM is reached by the expanded bus on ports 0 and 2. An alternate configuration allows dynamic partitioning of a 64k space as shown in Figure 3. Selecting PES=1 provides another 64k of potential data storage or memory-mapped peripheral space as shown in Figure 4. These selections are made using special function registers. The memory map and its controls are covered in detail in the Secure Microcontroller User’s Guide. 6 of 27 DS5001FP Figure 2. MEMORY MAP IN NONPARTITIONABLE MODE (PM = 1) 7 of 27 DS5001FP Figure 3. MEMORY MAP IN PARTITIONABLE MODE (PM = 0) NOTE: PARTITIONABLE MODE IS NOT SUPPORTED WHEN MSEL PIN = 0 (128kB MODE). 8 of 27 DS5001FP Figure 4. MEMORY MAP WITH PES = 1 9 of 27 DS5001FP Figure 5 illustrates a typical memory connection for a system using a 128kB SRAM. Note that in this configuration, both program and data are stored in a common RAM chip Figure 6 shows a similar system with using two 32kB SRAMs. The byte-wide address bus connects to the SRAM address lines. The bidirectional byte-wide data bus connects the data I/O lines of the SRAM. Figure 5. CONNECTION TO 128k x 8 SRAM 10 of 27 DS5001FP Figure 6. DS5001FP CONNECTION TO 64k x 8 SRAM POWER MANAGEMENT The DS5001FP monitors VCC to provide power-fail reset, early warning power-fail interrupt, and switch over to lithium backup. It uses an internal bandgap reference in determining the switch points. These are called VPFW, VCCMIN, and VLI, respectively. When VCC drops below VPFW, the DS5001FP performs an interrupt vector to location 2Bh if the power-fail warning was enabled. Full processor operation continues regardless. When power falls further to VCCMIN, the DS5001FP invokes a reset state. No further code execution is performed unless power rises back above VCCMIN. All decoded chip enables and the R/ W signal go to an inactive (logic 1) state. VCC is still the power source at this time. When VCC drops further to below VLI, internal circuitry switches to the lithium cell for power. The majority of internal circuits are disabled and the remaining nonvolatile states are retained. Any devices connected VCCO are powered by the lithium cell at this time. VCCO is at the lithium battery voltage minus approximately 0.45V. This drop varies depending on the load. Low power SRAMs should be used for this reason. When using the DS5001FP, the user must select the appropriate battery to match the RAM data retention current and the desired backup lifetime. Note that the lithium cell is only loaded when VCC < VLI. The User’s Guide has more information on this topic. The trip points VCCMIN and VPFW are listed in the Electrical Specifications section. 11 of 27 DS5001FP ABSOLUTE MAXIMUM RATINGS Voltage Range on Any Pin Relative to Ground…………………………..…………………….-0.3V to (VCC + 0.5V) Voltage Range on VCC Related to Ground………………………………………………………………-0.3V to 6.0V Operating Temperature Range………………………………………………………………………...-40°C to +85°C Storage Temperature Range (Note 1)………………………………………………………………..-55°C to +125°C Soldering Temperature…………………………………………………….See IPC/JEDEC J-STD-020 Specification This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. Note 1: Storage temperature is defined as the temperature of the device when VCC = 0V and VLI = 0V. In this state, the contents of SRAM are not battery-backed and are undefined. DC CHARACTERISTICS (VCC = 5V ±10%, TA = 0°C to +70°C.) PARAMETER Input Low Voltage Input High Voltage Input High Voltage (RST, XTAL1, PROG ) Output Low Voltage at IOL = 1.6mA (Ports 1, 2, 3, PF ) Output Low Voltage at IOL = 3.2mA (Ports 0, ALE, PSEN , BA15–0, BD7–0, R/ W , CE1N , CE 1–4, PE 1–4, VRST) Output High Voltage at IOH = -80µA (Ports 1, 2, 3) Output High Voltage at IOH = -400µA (Ports 0, ALE, PSEN , PF , BA15–0, BD7–0, R/ W , CE1N , CE 1–4, PE 1–4, VRST) Input Low Current VIN = 0.45V (Ports 1, 2, 3) Transition Current; 1 to 0 VIN = 2.0V (Ports 1, 2, 3) (0°C to +70°C) Transition Current; 1 to 0 VIN = 2.0V (Ports 1, 2, 3) (-40°C to +85°C) SYMBOL VIL VIH1 MIN -0.3 2.0 VIH2 3.5 TYP MAX +0.8 VCC + 0.3 UNITS V V NOTES 1 1 VCC + 0.3 V 1 VOL1 0.15 0.45 V 1, 11 VOL2 0.15 0.45 V 1 VOH1 2.4 4.8 V 1 VOH2 2.4 4.8 V 1 IIL -50 µA ITL -500 µA ITL -600 µA 12 of 27 10 DS5001FP DC CHARACTERISTICS (continued) (VCC = 5V ±10%, TA = 0°C to +70°C.) PARAMETER Input Leakage Current 0.45 < VIN < VCC (Port 0, MSEL) RST Pulldown Resistor (0°C to +70°C) RST Pulldown Resistor (-40°C to +85°C) VRST Pullup Resistor PROG Pullup Resistor Power-Fail Warning Voltage (0°C to +70°C) Power-Fail Warning Voltage (-40°C to +85°C) Minimum Operating Voltage (0°C to +70°C) Minimum Operating Voltage (-40°C to +85°C) Operating Voltage Lithium Supply Voltage Operating Current at 16MHz Idle Mode Current at 12MHz (0°C to +70°C) Idle Mode Current at 12MHz (-40°C to +85°C) Stop Mode Current Pin Capacitance Output Supply Voltage (VCCO) Output Supply Battery-Backed Mode (VCCO, CE 1-4, PE 1-2) (0°C to +70°C) Output Supply Battery-Backed Mode (VCCO, CE 1-4, PE 1-2) (-40°C to +85°C) Output Supply Current at VCCO = VCC - 0.45V Lithium-Backed Quiescent Current (0°C to +70°C) Lithium-Backed Quiescent Current (-40°C to +85°C) With BAT = 3.0V (0°C to +70°C) Reset Trip Point With BAT = 3.0V in Stop Mode (-40°C to +85°C) With BAT = 3.0V (0°C to +70°C) SYMBOL MIN TYP IIL MAX UNITS +10 µA RRE 40 150 kW RRE 30 180 kW RVR RPR 4.7 40 NOTES 10 kW kW VPFW 4.25 4.37 4.50 V 1 VPFW 4.1 4.37 4.6 V 1, 10 VCCMIN 4.00 4.12 4.25 V 1 VCCMIN 3.85 4.09 4.25 V 1, 10 VCC VLI ICC VCCMIN 2.5 5.5 4.0 36 V V mA 1 1 2 IIDLE 7.0 mA 3 IIDLE 8.0 mA 3, 10 ISTOP CIN 80 10 µA pF 4 5 VCCO1 VCC -0.45 V 1, 2 VCCO2 VLI -0.65 V 1, 8 VCCO2 VLI -0.9 V 1, 8, 10 75 mA 6 ICCO1 ILI 5 75 nA 7 ILI 75 500 nA 7 13 of 27 4.0 4.25 1 3.85 4.25 1, 10 4.4 4.65 1 DS5001FP AC CHARACTERISTICS: EXPANDED BUS MODE TIMING SPECIFICATIONS (VCC = 5V ±10%, TA = 0°C to +70°C.) # 1 2 3 4 5 PARAMETER Oscillator Frequency ALE Pulse Width Address Valid to ALE Low Address Hold After ALE Low ALE Low to Valid Instruction In SYMBOL 1/ tCLK tALPW tAVALL tAVAAV at 12MHz at 16MHz tALLPSL tPSPW 13 14 15 PSEN Low to Address Float tPSLAZ tRDPW tWRPW 16 RD Low to Valid Data In 17 18 Data Hold After RD High Data Float After RD High 19 ALE Low to Valid Data In 20 Valid Address to Valid Data In 21 22 23 ALE Low to RD or WR Low Address Valid to RD or WR Low Data Valid to WR Going Low at 12MHz Data Valid to WR High at 16MHz tALLRDL tAVRDL tDVWRL Data Valid After WR High RD Low to Address Float RD or WR High to ALE High tWRHDV tRDLAZ tRDHALH 8 9 10 11 12 24 25 26 27 RD Pulse Width WR Pulse Width at 12MHz at 16MHz tCLK - 25 3tCLK - 35 0 tCLK - 20 tCLK - 8 0 6tCLK - 100 6tCLK - 100 tRDHDV tRDHDZ at 12MHz at 16MHz at 12MHz at 16MHz 0 tALLVD tAVDV tDVWRH 14 of 27 3tCLK - 50 4tCLK - 130 tCLK - 60 7tCLK - 150 7tCLK - 90 tCLK - 50 tCLK - 40 ns ns ns ns ns ns ns 5tCLK - 165 5tCLK - 105 tRDLDV ns ns 5tCLK - 150 5tCLK - 90 tAVVI UNITS MHz ns ns ns ns ns 3tCLK - 150 3tCLK - 90 tPSLVI tPSIV tPSIX tPSAV MAX 16 4tCLK - 150 4tCLK - 90 tALLVI ALE Low to PSEN Low PSEN Pulse Width at 12MHz PSEN Low to Valid Instruction at 16MHz In Input Instruction Hold After PSEN Going High Input Instruction Float After PSEN Going High Address Hold After PSEN Going High at 12MHz Address Valid to Valid Instruction In at 16MHz 6 7 MIN 1.0 2tCLK - 40 tCLK - 40 tCLK - 35 2tCLK - 70 8tCLK - 150 8tCLK - 90 9tCLK - 165 9tCLK - 105 3tCLK + 50 ns ns ns ns ns ns ns ns ns 0 tCLK + 50 ns ns ns DS5001FP EXPANDED PROGRAM-MEMORY READ CYCLE EXPANDED DATA-MEMORY READ CYCLE 15 of 27 DS5001FP EXPANDED DATA-MEMORY WRITE CYCLE 16 of 27 DS5001FP AC CHARACTERISTICS: EXTERNAL CLOCK DRIVE (VCC = 5V ±10%, TA = 0°C to +70°C.) # PARAMETER 28 External Clock-High Time 29 External Clock-Low Time 30 External Clock-Rise Time 31 External Clock-Fall Time SYMBOL at 12MHz at 16MHz at 12MHz at 16MHz at 12MHz at 16MHz at 12MHz at 16MHz EXTERNAL CLOCK TIMING 17 of 27 tCLKHPW tCLKLPW tCLKR tCLKF MIN 20 MAX UNITS ns 15 20 ns 15 20 15 20 15 ns ns DS5001FP AC CHARACTERISTICS: POWER CYCLE TIME (VCC = 5V ±10%, TA = 0°C to +70°C.) # 32 33 34 PARAMETER Slew Rate from VCCMIN to VLI Crystal Startup Time Power-On Reset Delay SYMBOL tF tCSU tPOR POWER CYCLE TIMING 18 of 27 MIN 130 MAX (Note 9) 21,504 UNITS µs tCLK DS5001FP AC CHARACTERISTICS: SERIAL PORT TIMING—MODE 0 (VCC = 5V ±10%, TA = 0°C to +70°C.) # 35 PARAMETER Serial-Port Clock-Cycle Time SYMBOL tSPCLK MIN 12tCLK 36 Output-Data Setup to Rising-Clock Edge tDOCH 10tCLK - 133 ns 37 Output-Data Hold After Rising-Clock Edge tCHDO 2tCLK - 117 ns 38 Clock-Rising Edge to Input-Data Valid tCHDV 39 Input-Data Hold After Rising-Clock Edge tCHDIV SERIAL PORT TIMING—MODE 0 19 of 27 MAX 10tCLK - 133 0 UNITS µs ns ns DS5001FP AC CHARACTERISTICS: BYTE-WIDE ADDRESS/DATA BUS TIMING (VCC = 5V ±10%, TA = 0°C to +70°C.) # 40 41 42 43 44 45 46 47 48 49 50 51 PARAMETER Delay to Byte-Wide Address Valid from CE1 , CE2 , or CE1N Low During Op Code Fetch Pulse Width of CE 1-4, PE 1-4 or CE1N Byte-Wide Address Hold After CE1 , CE2 , or CE1N High During Op Code Fetch Byte-Wide Data Setup to CE1 , CE2 , or CE1N High During Op Code Fetch Byte-Wide Data Hold After CE1 , CE2 or CE1N High During Op Code Fetch Byte-Wide Address Hold After CE 1-4, PE 1-4, or CE1N High During MOVX Delay from Byte-Wide Address Valid CE 1-4, PE 1-4, or CE1N Low During MOVX Byte-Wide Data Setup to CE 1-4, PE 1-4, or CE1N High During MOVX (read) Byte-Wide Data Hold After CE 1-4, PE 1-4, or CE1N High During MOVX (read) Byte-Wide Address Valid to R/ W Active During MOVX (write) Delay from R/ W Low to Valid Data Out During MOVX (write) Valid Data-Out Hold Time from CE 1-4, PE 1-4, or CE1N High SYMBOL MIN tCE1LPA MAX UNITS 30 ns tCEPW 4tCLK - 35 ns tCE1HPA 2tCLK - 20 ns tOVCE1H 1tCLK + 40 ns tCE1HOV 0 ns tCEHDA 4tCLK - 30 ns tCELDA 4tCLK - 35 ns tDACEH 1tCLK + 40 ns tCEHDV 0 ns tAVRWL 3tCLK - 35 ns tRWLDV 20 ns tCEHDV 1tCLK - 15 ns 52 Valid Data-Out Hold Time from R/ W High tRWHDV 0 ns 53 Write Pulse Width (R/ W Low Time) tRWLPW 6tCLK - 20 ns 20 of 27 DS5001FP BYTE-WIDE BUS TIMING RPC AC CHARACTERISTICS: DBB READ (VCC = 5V ±10%, TA = 0°C to +70°C.) # 54 55 56 57 58 59 PARAMETER CS , A0 Setup to RD CS , A0 Hold After RD RD Pulse Width CS , A0 to Data-Out Delay RD to Data-Out Delay RD to Data-Float Delay SYMBOL tAR tRA tRR tAD tRD tRDZ MIN 0 0 160 0 MAX 130 130 85 UNITS ns ns ns ns ns ns RPC AC CHARACTERISTICS: DBB WRITE (VCC = 5V ±10%, TA = 0°C to +70°C.) # 60 61A 61B 62 63 64 PARAMETER CS , A0 Setup to WR CS , Hold After WR A0, Hold After WR SYMBOL tAW tWA tWA MIN 0 0 20 tWW tDW 160 130 ns ns tWD 20 ns WR Pulse Width Data Setup to WR Data Hold After WR 21 of 27 MAX UNITS ns ns ns DS5001FP AC CHARACTERISTICS: DMA (VCC = 5V ±10%, TA = 0°C to +70°C.) # 65 66 PARAMETER DACK to WR or RD RD or WR to DACK 67 68 DACK to Data Valid SYMBOL tACC tCAC MIN 0 0 MAX UNITS ns ns tACD tCRQ 0 130 110 ns ns SYMBOL tPRA tPRI MIN 48 48 MAX UNITS CLKS CLKS RD or WR to DRQ Cleared AC CHARACTERISTICS: PROG (VCC = 5V ±10%, TA = 0°C to +70°C.) # 69 70 PARAMETER PROG Low to Active PROG High to Inactive 22 of 27 DS5001FP RPC TIMING MODE 23 of 27 DS5001FP NOTES: All parameters apply to both commercial and industrial temperature operation unless otherwise noted. 1) All voltages are referenced to ground. 2) Maximum operating ICC is measured with all output pins disconnected; XTAL1 driven with tCLKR, tCLKF = 10ns, VIL = 0.5V; XTAL2 disconnected; RST = PORT0 = VCC, MSEL = VSS. 3) Idle mode, IIDLE, is measured with all output pins disconnected; XTAL1 driven with tCLKR, tCLKF = 10ns, VIL = 0.5V; XTAL2 disconnected; PORT0 = VCC, RST = MSEL = VSS. 4) Stop mode, ISTOP, is measured with all output pins disconnected; PORT0 = VCC; XTAL2 not connected; RST = MSEL = XTAL1 = VSS. 5) Pin capacitance is measured with a test frequency: 1MHz, TA = +25°C. 6) ICCO1 is the maximum average operating current that can be drawn from VCCO in normal operation. 7) ILI is the current drawn from VLI input when VCC = 0V and VCCO is disconnected. 8) VCCO2 is measured with VCC < VLI, and a maximum load of 10µA on VCCO. 9) Crystal startup time is the time required to get the mass of the crystal into vibrational motion from the time that power is first applied to the circuit until the first clock pulse is produced by the on-chip oscillator. The user should check with the crystal vendor for a worst-case specification on this time. 10) This parameter applies to industrial temperature operation. 11) PF pin operation is specified with VBAT ³ 3.0V. 24 of 27 DS5001FP PACKAGE INFORMATION (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/DallasPackInfo.) 80-PIN MQFP DIM A A1 A2 B C D D1 E E1 e L MM MIN MAX 3.40 0.25 2.55 2.87 0.30 0.50 0.13 0.23 23.70 24.10 19.90 20.10 17.70 18.10 13.90 14.10 0.80 BSC 0.65 0.95 56-G4005-001 25 of 27 DS5001FP 44-PIN MQFP 26 of 27 DS5001FP REVISION HISTORY The following represent the key differences between the 112795 and 073096 version of the DS5001FP data sheet. Please review this summary carefully. 1) Change VCC02 specification from VLI - 0.5 to VLI - 0.65 (PCN F62501). 2) Update mechanical specifications. The following represent the key differences between the 073096 and 111996 version of the DS5001FP data sheet. Please review this summary carefully. 1) Change VCC01 from VCC - 0.3 to VCC - 0.35. The following represent the key differences between the 111996 and 061297 version of the DS5001FP data sheet. Please review this summary carefully. 1) PF signal moved from VOL2 test specification to VOL1. PCN No. (D72502) 2) AC characteristics for battery-backed SDI pulse specification added. The following represent the key differences between the 061297 and 051099 version of the DS5001FP data sheet. Please review this summary carefully. 1) Reduced absolute maximum voltage to VCC + 0.5V. 2) Added note clarifying storage temperature specification is for non-battery-backed state. 3) Changed RRE min (industrial temp range) from 40kW to 30kW. 4) Changed VPFW max (industrial temp range) from 4.5V to 4.6V. 5) Added industrial specification for ILI. 6) Reduced tCE1HOV and tCEHDV from 10ns to 0ns. The following represent the key differences between the 051099 and 052499 version of the DS5001FP data sheet. Please review this summary carefully. 1) Minor markups and ready for approval. The following represent the key differences between the 052499 and 052302 version of the DS5001FP data sheet. Please review this summary carefully. 1) Added information relating to 44-pin package. 2) Updated VCCO1 and ICCO1 specifications to reflect 0.45V internal voltage drop instead of 0.35V. The following represent the key differences between the 052302 and 070605 version of the DS5001FP data sheet. Please review this summary carefully. 1) Added Pb-free part to Ordering Information table. 2) Added operating voltage specification. (This is not a new specification because operating voltage is implied in the testing limits, but rather a clarification.) 3) Updated Absolute Maximum Ratings soldering temperature to reference JEDEC standard. 27 of 27 Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product. No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products · Printed USA The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.