DDU7F data 3 delay devices, inc. 10-TAP, TTL-INTERFACED FIXED DELAY LINE (SERIES DDU7F) FEATURES • • • • • • PACKAGES Ten equally spaced outputs Fits standard 14-pin DIP socket Low profile Auto-insertable Input & outputs fully TTL interfaced & buffered 10 T2L fan-out capability IN 1 14 VCC N/C 2 13 T1 T2 3 12 T3 T4 4 11 T5 T6 5 10 T7 T8 6 9 T9 GND 7 8 T10 DDU7F-xx DDU7F-xxA2 DDU7F-xxB2 DDU7F-xxM DIP Gull-Wing J-Lead Military DIP FUNCTIONAL DESCRIPTION IN T2 T4 T6 T8 T10 N/C GND 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC T1 T3 T5 T7 T9 N/C N/C Military SMD DDU7F-xxMC3 PIN DESCRIPTIONS The DDU7F-series device is a 10-tap digitally buffered delay line. The IN Signal Input signal input (IN) is reproduced at the outputs (T1-T10), shifted in time by an T1-T10 Tap Outputs amount determined by the device dash number. The nominal tap-to-tap VCC +5 Volts delay increment is given by 1/10 of the dash number. For dash numbers GND Ground less than 50, the total delay of the line is measured from T1 to T10, with the nominal value given by 9 times the increment. The inherent delay from IN to T1 is nominally 3.5ns. For dash numbers greater than or equal to 50, the total delay of the line is measured from IN to T10, with the nominal value given by the dash number. DASH NUMBER SPEC.’S SERIES SPECIFICATIONS • • • • • • Minimum input pulse width: 20% of total delay Output rise time: 2ns typical Supply voltage: 5VDC ± 5% Supply current: ICCL = 50ma typical ICCH = 15ma typical Operating temperature: 0° to 70° C Temp. coefficient of total delay: 100 PPM/°C 3.5ns VCC IN 10% T1 10% T2 10% T3 10% T4 10% T5 10% T6 10% T7 10% T8 10% T9 T10 GND Functional diagram for dash numbers < 50 10% VCC IN 10% T1 10% T2 10% T3 10% T4 10% T5 10% T6 10% T7 10% T8 Part Number DDU7F-10 DDU7F-20 DDU7F-25 DDU7F-50 DDU7F-100 DDU7F-150 DDU7F-200 DDU7F-250 DDU7F-300 DDU7F-400 DDU7F-500 Total Delay (ns) 9 ± 2.0 * 18 ± 2.0 * 22.5 ± 2.0 * 50 ± 2.5 100 ± 5.0 150 ± 7.5 200 ± 10.0 250 ± 12.5 300 ± 15.0 400 ± 20.0 500 ± 25.0 Delay Per Tap (ns) 1.0 ± 0.5 2.0 ± 1.0 2.5 ± 1.0 5.0 ± 2.0 10.0 ± 3.0 15.0 ± 3.0 20.0 ± 3.0 25.0 ± 3.0 30.0 ± 3.0 40.0 ± 4.0 50.0 ± 5.0 * Total delay is referenced to first tap Input to first tap = 3.5ns ± 1ns NOTE: Any dash number between 10 and 500 not shown is also available. 10% T9 T10 GND Functional diagram for dash numbers >= 50 1997 Data Delay Devices Doc #97016 1/29/97 DATA DELAY DEVICES, INC. 3 Mt. Prospect Ave. Clifton, NJ 07013 1 DDU7F APPLICATION NOTES Delay Devices if your application requires device testing at a specific input condition. HIGH FREQUENCY RESPONSE The DDU7F tolerances are guaranteed for input pulse widths and periods greater than those specified in the test conditions. Although the device will function properly for pulse widths as small as 20% of the total delay and periods as small as 40% of the total delay (for a symmetric input), the delays may deviate from their values at low frequency. However, for a given input condition, the deviation will be repeatable from pulse to pulse. Contact technical support at Data POWER SUPPLY BYPASSING The DDU7F relies on a stable power supply to produce repeatable delays within the stated tolerances. A 0.1uf capacitor from VCC to GND, located as close as possible to the VCC pin, is recommended. A wide VCC trace and a clean ground plane should be used. DEVICE SPECIFICATIONS TABLE 1: ABSOLUTE MAXIMUM RATINGS PARAMETER DC Supply Voltage Input Pin Voltage Storage Temperature Lead Temperature SYMBOL VCC VIN TSTRG TLEAD MIN -0.3 -0.3 -55 MAX 7.0 VCC+0.3 150 300 UNITS V V C C NOTES 10 sec TABLE 2: DC ELECTRICAL CHARACTERISTICS (0C to 70C, 4.75V to 5.25V) PARAMETER High Level Output Voltage SYMBOL VOH Low Level Output Voltage VOL High Level Output Current Low Level Output Current High Level Input Voltage Low Level Input Voltage Input Clamp Voltage Input Current at Maximum Input Voltage High Level Input Current Low Level Input Current Short-circuit Output Current Output High Fan-out Output Low Fan-out IOH IOL VIH VIL VIK IIHH Doc #97016 1/29/97 IIH IIL IOS MIN 2.5 TYP 3.4 MAX UNITS V 0.35 0.5 V -1.0 20.0 0.8 -1.2 0.1 mA mA V V V mA 20 -0.6 -150 25 12.5 µA mA mA Unit Load 2.0 -60 NOTES VCC = MIN, IOH = MAX VIH = MIN, VIL = MAX VCC = MIN, IOL = MAX VIH = MIN, VIL = MAX VCC = MIN, II = IIK VCC = MAX, VI = 7.0V VCC = MAX, VI = 2.7V VCC = MAX, VI = 0.5V VCC = MAX DATA DELAY DEVICES, INC. Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com 2 DDU7F PACKAGE DIMENSIONS 14 13 12 11 10 9 8 Lead Material: Nickel-Iron alloy 42 TIN PLATE 14 13 12 11 10 1 2 3 4 5 6 9 8 .440 MAX. 7 .280 MAX. .780 MAX. 1 2 3 4 5 6 7 .830 MAX. .290 MAX. .030 .290 ±.005 MAX. .015 TYP. .010±.002 .018 TYP. .070 MAX. .195 ±.010 .350 MAX. .600±.010 6 Equal spaces each .100±.010 Non-Accumulative .600 TYP. .040 TYP. 14 13 12 11 10 9 .010 TYP. 2 .090 3 4 5 6 .040 TYP. .020 TYP. 8 14 13 12 11 10 9 .270 TYP. 1 1 2 .110 .050 TYP. DDU7F-xxA2 (Commercial Gull-Wing) 3 4 5 2 3 4 .040 TYP. 5 .090 6 7 .100 .700 .880±.020 7 .100 .600 .790 MAX. .350 MAX. .110 TYP. .010±.002 9 .882 ±.005 .710 .590 ±.005 MAX. 1 6 DDU7F-xxB2 (Commercial J-Lead) .020 TYP. 16 15 14 13 12 11 10 .320 TYP. .270 TYP. 7 .300 MAX. .050 TYP. 8 .430 TYP. .100 .600 .790 MAX. .300 TYP. DDU7F-xxM (Military DIP) DDU7F-xx (Commercial DIP) .020 TYP. .010 TYP. .020 TYP. .007 ±.005 8 .280 MAX. .050 ±.010 DDU7F-xxMC3 (Military Gull-Wing) Doc #97016 1/29/97 DATA DELAY DEVICES, INC. 3 Mt. Prospect Ave. Clifton, NJ 07013 3 DDU7F DELAY LINE AUTOMATED TESTING TEST CONDITIONS INPUT: Ambient Temperature: 25oC ± 3oC Supply Voltage (Vcc): 5.0V ± 0.1V Input Pulse: High = 3.0V ± 0.1V Low = 0.0V ± 0.1V Source Impedance: 50Ω Max. Rise/Fall Time: 3.0 ns Max. (measured between 0.6V and 2.4V ) Pulse Width: PWIN = 1.5 x Total Delay Period: PERIN = 10 x Total Delay OUTPUT: Load: Cload: Threshold: 1 FAST-TTL Gate 5pf ± 10% 1.5V (Rising & Falling) NOTE: The above conditions are for test only and do not in any way restrict the operation of the device. PRINTER COMPUTER SYSTEM PULSE GENERATOR OUT IN TRIG DEVICE UNDER TEST (DUT) T1 REF T2 IN T3 TRIG TIME INTERVAL COUNTER T4 T5 T6 T7 T8 T9 T10 Test Setup PERIN PWIN TRISE INPUT SIGNAL TFALL VIH 2.4V 1.5V 0.6V 2.4V 1.5V 0.6V TRISE OUTPUT SIGNAL VIL TFALL VOH 1.5V 1.5V VOL Timing Diagram For Testing Doc #97016 1/29/97 DATA DELAY DEVICES, INC. Tel: 973-773-2299 Fax: 973-773-9672 http://www.datadelay.com 4