ELM ELM328SM

ELM328
OBD Device Identifier Test IC
Description
The ELM327 “OBD to RS232 Interpreter” IC
introduced a new feature with v1.3 - the ability for a
user to store a unique 12 character identifier code.
This identifier can be read at any time, but it can not
be changed once it has been set.
Software developers will have difficulty proving
their code with this “write once, read many” feature,
so we have introduced the ELM328 integrated circuit
as a development tool for them.
The ELM328 is a special version of the ELM327
- it is identical electrically, but the firmware has one
new command (AT @0) that resets the @2 identifier
lock.
Features
• Based on the latest version of the ELM327
• Allows testing of the @2 and @3 functions
Applications
Connection Diagram
PDIP and SOIC
(top view)
MCLR
OBD Tx LED
Vmeasure
OBD Rx LED
J1850 Volts
RS232 Tx LED
J1850 Bus+
RS232 Rx LED
Memory
CAN Rx
Baud Rate
CAN Tx
LFmode
ISO L
VSS
ISO K
XT1
VDD
XT2
VSS
VPW In
RS232 Rx
ISO In
RS232 Tx
PWM In
PwrCtrl / Busy
J1850 Bus-
IgnMon / RTS
• ELM327 code development only
(not suitable for OBD scan tools)
Usage Notes
1. The ELM328 electrical connections and characteristics are identical to the ELM327 integrated circuit,
so that it can be directly substituted into an ELM327 circuit.
2. The ID string sent at power up, or in response to AT I is “ELM328 v1.4” and not “ELM327 v1.4”.
3. The ELM328 offers one new AT command - the @0 command, which unlocks the @2 identifier,
restoring it to the factory new condition. ELM327 software developers may repeatedly experiment with
the @2 and @3 commands, using AT @0 to reset the identifier as required.
4. The ability to send OBD commands has been removed from the ELM328. If you try to send an OBD
command, the ELM328 will always act as if no ECU is connected, and no data will be transmitted.
Ordering Information
These integrated circuits are 28 pin devices, available in either a 300 mil wide plastic (‘skinny’) DIP format
or in a 300 mil SOIC surface mount type of package. To order, add the appropriate suffix to the part number:
300 mil 28 pin Plastic DIP.............................ELM328P
ELM328DSB
300 mil 28 pin SOIC............................ ELM328SM
Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
1 of 2
ELM328
Absolute Maximum Ratings
Storage Temperature....................... -65°C to +150°C
Ambient Temperature with
Power Applied....................................-40°C to +85°C
Voltage on VDD with respect to VSS..... -0.3V to +7.5V
Note:
These values are given as a design guideline only.
The ability to operate to these levels is neither
inferred nor recommended, and stresses beyond
those listed here will likely damage the device.
Voltage on any other pin with
respect to VSS........................... -0.3V to (VDD + 0.3V)
Electrical Characteristics
All values are for operation at 25°C and a 5V supply, unless otherwise noted. The ELM328 is electrically identical to the
ELM327 in all respects. For further information, refer to the ELM327 data sheet, and to note 1 below.
Characteristic
Minimum
Typical
Supply voltage, VDD
4.5
5.0
VDD rate of rise
0.05
Average supply current, IDD
Brown-out reset voltage
Notes:
Maximum Units
5.5
12
4.11
4.33
4.55
Conditions
V
V/ms
see note 2
mA
see note 3
V
1. This integrated circuit is based on Microchip Technology Inc.’s PIC18F2480 device. For further device
specifications, and clarification of those given, please refer to the appropriate Microchip documentation
(available at http://www.microchip.com/).
2. This spec must be met in order to ensure that a correct power on reset occurs. It is quite easily achieved
using most common types of supplies, but may be violated if one uses a slowly varying supply voltage, as
may be obtained through direct connection to solar cells or some charge pump circuits.
3. Device only. Does not include any load currents.
All rights reserved. Copyright 2008, 2010 by Elm Electronics Inc.
Every effort is made to verify the accuracy of information provided in this document, but no representation or warranty can be
given and no liability assumed by Elm Electronics with respect to the accuracy and/or use of any products or information
described in this document. Elm Electronics will not be responsible for any patent infringements arising from the use of these
products or information, and does not authorize or warrant the use of any Elm Electronics product in life support devices and/or
systems. Elm Electronics reserves the right to make changes to the device(s) described in this document in order to improve
reliability, function, or design.
ELM328DSB
Elm Electronics – Circuits for the Hobbyist
www.elmelectronics.com
2 of 2