EVERLIGHT 15-21-B6C-ZQ1R1N-2T

Technical Data Sheet
1206 Package Chip LED (1.0 mm Height)
15-21/B6C-ZQ1R1N/2T
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain with in RoHS complaint version.
Descriptions
․The 15-21 SMD LED is much smaller than lead
frame type components, thus enable smaller
board size, higher packing density, reduced
storage space and finally smaller equipment to be
obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Part No.
15-21/B6C-ZQ1R1N/2T
Chip
Material
Emitted Color
Resin Color
Blue
Water Clear
InGaN
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 1 of 10
15-21/B6C-ZQ1R1N/2T
Package Outline Dimensions
1.2
0.8
1.5
1.2
1.5
1.6
1.4
0.8
Note: Tolerances Unless Dimension ±0.1mm , Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 2 of 10
15-21/B6C-ZQ1R1N/2T
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Rating
Unit
Reverse Voltage
VR
5
V
Forward Current
IF
25
mA
IFP
100
mA
Power Dissipation
Pd
95
mW
Electrostatic Discharge(HBM)
ESD
150
V
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40~ +90
℃
Soldering Temperature
Tsol
Peak Forward Current
(Duty 1/10 @1KHz)
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Luminous Intensity
Iv
72
-----
140
mcd
Viewing Angle
2θ1/2
-----
130
-----
deg
Peak Wavelength
λp
-----
468
-----
nm
λd
465
-----
475
nm
Spectrum Radiation
Bandwidth
△λ
-----
25
-----
nm
Forward Voltage
VF
2.70
-----
3.70
V
Reverse Current
IR
-----
-----
50
μA
Dominant Wavelength
Condition
IF=20mA
VR=5V
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 3 of 10
15-21/B6C-ZQ1R1N/2T
Bin Rang Of Dom. Wavelength
Group
Z
Bin
Min
Max
X
465
470
Y
470
475
Unit
Condition
nm
IF=20mA
Unit
Condition
mcd
IF=20mA
Unit
Condition
V
IF=20mA
Bin Rang Of Luminous Intensity
Bin
Min
Max
Q1
72.0
90.0
Q2
90.0
112.0
R1
112.0
140.0
Bin Rang Of Luminous Voltage
Group
N
Bin
Min
Max
10
2.70
2.90
11
2.90
3.10
12
3.10
3.30
13
3.30
3.50
14
3.50
3.70
Notes:
1.Tolerance of Luminous Intensity ±11%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 4 of 10
15-21/B6C-ZQ1R1N/2T
Typical Electro-Optical Characteristics Curves
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 5 of 10
15-21/B6C-ZQ1R1N/2T
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
Pb
EVERLIGHT
CPN :
P N : XXXXXXXXXXXXX
RoHS
XXXXXXXXXXXXX
CAT : XXX
HUE : XXX
REF : XXX
QTY : XXX
LOT NO : XXXXXXXXXX
Reference : XXXXXXXX
MADE IN TAIWAN
Reel Dimensions
Note: Tolerances Unless Dimension ±0.1mm , Unit = mm
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 6 of 10
15-21/B6C-ZQ1R1N/2T
Carrier Tape Dimensions: Loaded quantity 2000 PCS per reel
Note: Tolerances Unless Dimension ±0.1mm , Unit = mm
Moisture Resistant Packaging
Label
Aluminum moisture-proof bag
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Desiccant
Label
Rev .4
Prepared by:Paul
Page: 7 of 10
15-21/B6C-ZQ1R1N/2T
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
No.
Items
Test Condition
1
Reflow Soldering
Temp. : 260℃±5℃
Min
5 sec.
Test
Sample
Ac/Re
Hours/Cycles Size
22 Pcs.
0/1
Temperature Cycle
H : +100℃ 15min
∫ 5 min
L : -40℃ 15min
300 Cycles 22 PCS.
0/1
3
Thermal Shock
H : +100℃ 5min
∫ 10 sec
L : -10℃ 5min
300 Cycles 22 PCS.
0/1
4
High Temperature
Storage
Temp. : 100℃
1000 Hrs.
22 PCS.
0/1
5
Low Temperature
Storage
Temp. : -40℃
1000 Hrs.
22 PCS.
0/1
6
DC Operating Life
IF = 20 mA
1000 Hrs.
22 PCS.
0/1
7
High Temperature /
High Humidity
85℃/85% RH
1000 Hrs.
22 PCS.
0/1
2
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
6 Min.
Rev .4
Prepared by:Paul
Page: 8 of 10
15-21/B6C-ZQ1R1N/2T
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3 After opening the package: The LED's floor life is 1 year under 30℃ or less and 60% RH or less.
If unused LEDs remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 9 of 10
15-21/B6C-ZQ1R1N/2T
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
http://www.everlight.com
Device No: DSE-0001407
Prepared date:22-Sep -2009
Rev .4
Prepared by:Paul
Page: 10 of 10